Ethernet Extender
Ethernet Extender
Feature
Ethernet Extender
Use coaxial cable to transmit Ethernet signal and power, maximum distance up to 2km;
Network delay less than 1ms;
This Ethernet extender is consisted of SV-Unit and IPC-Unit which can use in pair or one-to-many. It
Optional transmission medium, coaxial cable, power line, telephone cable or UTP cable;
uses coaxial cable or other kind cable to transfer Ethernet signal and power, and power for cameras and
Meet single mode, link mode and star mode network at the same time;
other devices. This product is very suitable for long distance transmission of Ethernet signal and power. It
Loop circuit mode, if there is one breakdown in the circuit, the system still can work normally;
Meet Standard: IEEE802.3 10BASE-T, IEEE802.3u 100BASE-TX;
can be used in security network video surveillance.
Appearance and structure : Solid and delicate, meet MIT rack installation standard;
Application (Point-to-Point)
Protection: Excellent circuit isolation protection, effectively improve product's lightning protection,
ESD and anti-interference ability .
LC
D
Notice
1)Transmission distance is related to the connecting cable. To get better transmitting image, please
C
use standard coaxial cable or Cat5/5e/6 cable.
a
/5
VR
t5
N
e
2) The network rate decreases with increasing of transmission distance;
/6
3) When point-to-multi point, the maximum speed rate is 100Mbps, pleas don't connect with too many
IPC Units.
DC
48
V
o
SV
C
xi
Un
a
w
lC
it
a
o
V u
2 p
1 t
C u
D rO
P
a
e
Board diagram
b
le
IP
t
C
IPC Unit
a
Un
C
it
t5
SV Unit
/5
e
IP
/6
Ca
m
er
a
1
1
2
Application (Point-to-Multi Point)
Power
Ethernet
Ethernet
EOC
EPOC
EOC
EPOC
LC
DC12V
Ethernet Port
L
D
2
Power
Coaxial Cable Port
Signal Indicator
o
POWER OUT
Ethernet Port Coaxial Cable Port
Signal Indicator
o
p
POWER IN
C
ir
cu
it
a
/5
48-57V DC
e
/6
e
Ca
/5
IP
t5
it
VR
t5
N
Un
a
V
C
12
C
C
IP
DC
12V DC
/6
m
er
Grounding Terminal
a
Power Output DC12V
Ground EPOC Power Input
DC48~57V
Terminal
DC
48
V
SV
o
Un
C
a
Pow
e
D C 1r O u t p u
t
2V
it
xi
a
lC
a
b
le
IP
C
Un
C
t5
it
a
e
Ca
/5
IP
/6
m
er
a
1
2
Ethernet Extender
Ethernet Extender
Trouble Shooting
Installation steps
Please check the following items before installation. If any missing, please contact the dealer.
Please find the following solution when the device doesn't work
Ethernet Extender-IPC Unit/Ethernet Extender-SV Unit
1pc
Please confirm if the installation is correct;
Power Adapter
1pc
Please confirm if the RJ45 cable order in accordance with the EIA/TIA568A or 568B industry
Hanger
2pcs
standards;
BNC Connector
2pcs
The maximum transmission distance is depend on the signal source and cable quality, please do not
User Manual
1pc
over the maximum transmission distance;
Please follow the following steps
Please replace a normal device with a failure one to check if the device is broken;
1) Please turn off the signal source and the device's power, installation with power on may damage the
If the problem still exist, please contact the factory.
device;
RJ 45 Making Method
2) Use network cable to connect IP camera with IPC's RJ45 port;
3) Use network cable to connect SV's RJ 45 port and NVR;
Instruments to be used: wire crimper, network tester. Wire sequence of RJ45 plug should conform with
4) Use telephone cable or UTP cable/Coaxial cable to connect with IPC and SV's transmission port;
EIA/TIA568A or 568B.
5) Check if the installation is correct and device is good, make sure all the connection is reliable and
power for the system;
6) Make sure every network device has power supply and work normally.
3) Line up the 8 pieces of cables per EIA/TIA 568A or 568B;
Specification
连接接口
4) Cut out 1.5 cm cable wrap and leave the bare wire;
Item
Description
Power Supply
Voltage Range
Power
Consumption
EPOC Power Voltage
IPC Unit Output Voltage
Ethernet Port
SV: Power adapter;
IPC: Powered by SV Unit through Coaxial Cable
DC48V-57V
output
48V-57V (IPC Unit without this input)
DC12V
EPOC Port: Use coaxial cable to transmit Ethernet signal and
power
Ethernet Port
Ethernet Port: 10/100Mbps
EPOC Port ues Coaxial Cable: Maximum 2km, transmission
rate decreases with increasing of transmission distance;
Transmission Distance
Ethernet port use Cat5\5e\6: 100m
LED Status
Indicator
1 (Red)
EPOC Ethernet
1 (Green)
RJ45 Ethernet
Protection
ESD
Working Temperature
1 (Green), 1 (Yellow) Indicat Link/act
1a Contact Discharge 3 Level
1b Air Discharge 3 Level
Per: IEC61000-4-2
-40℃~70℃
Storage Temperature
-40℃~70℃
Mechanical
Humidity (Noncondensing)
0~95%
Dimension (L×W×H)
82mm×100mm×25mm
Material
Aluminum
Color
Weight
Stability
MTBF
5) Plug 8 cables into RJ45 plug, make sure each cable is in each pin;
6) Then use wire crimper to crimp it;
7) Follow the 5 steps above to make the another end, following the same sequence of the first plug;
8) Using network tester to test the cable whether is working.
Whole machine<10W, other consumption for EPOC power
Power
Environmental
1) Shuck off about 2cm long the insulating layer, and bar the 4 pairs UTP cable;
2) Depart the 4 pairs UTP cable and straighten them;
pin color
pin
color
1
white/green
1
white/orange
2
green
2
orange
3
white/orange
3
white/green
4
blue
4
blue
5
white/blue
5
white/blue
6
orange
6
green
7
white/brown
7
white/brown
8
brown
8
brown
EIA/TIA 568A
EIA/TIA 568B
Notice
When choose RJ-45 make sure if one end is EIA/TIA568A,the other end should also be EIA/TIA568A.
When choose RJ-45 make sure if one end is EIA/TIA568B,the other end should also be EIA/TIA568B.
Black
IPC:180g;
SV:180g
>30000h
Product are subject to change without prior notice
3
4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising