Mounting of the CENTRALIS receiver RTS 2

Mounting of the CENTRALIS receiver RTS 2
Ref.5003509
INSTALLATIONguide
inteo
CENTRALIS receiver RTS 2
The CENTRALIS receiver RTS is a radio receiver for awnings compatible with all the
RTS controls and the INIS RT.
Commands are transmitted by radio (frequency 433.42 MHz).
With an INIS RT, the functioning of the CENTRALIS receiver RTS is a trip switch type :
▲, stop, ▼, stop,…
1
Installation:
2
Characteristics:
❏ Mains supply : 220-240 V~ 50/60 Hz
❏ Protection index: IP 44
❏ Operating temperature: -20°C to +50°C
❏ Class II product once installed
❏ Normally polluted environment
LED
Programming
button
▲▼
Built-in manual
security control
N N L
Hereby, SOMFY, declares that this equipment is in
compliance with the essential requirements and
other relevant provisions of Directive 1999/5/EC.
A Declaration of Conformity is available at the web
address www.somfy.com Heading CE
133 mm
Before connecting the unit, you must read the instructions carefully.
Mounting of the CENTRALIS receiver RTS 2 :
Recommendations :
150 mm
A
150 mm
40 mm
❏ Install the CENTRALIS receiver RTS with the cables entry pointing downwards to avoid water infiltration.
❏ Do no install the CENTRALIS receiver RTS against a metallic part
(it could affect the radio transmission).
❏ minimum distance between the receiver and the floor : 1,5 m.
❏ minimum distance between the receiver and the roof : 30 cm.
❏ minimum distance between the receiver and the transmitter : 30 cm.
❏ minimum distance between two receivers : 20 cm.
®
B Cabling of the CENTRALIS receiver RTS 2 :
The CENTRALIS receiver RTS is compatible with all standard SOMFY motors. Cabling arrangements are
shown in the diagram below. Respect the electrical standards in force as well as the following points:
- disconnect the mains before carrying out any work.
- be careful to avoid static electricity which could damage some electronic components.
- use flexible cables
- ensure that no longitudinal forces act on the cable carriers after installation
- do not forget to connect the earth wires.
Wiring principle
L = Main phase
N = Main neutral
N = Motor neutral
▲▼
▲ = Motor up
▼ = Motor down
N N L
MAIN
SUPPLY
Phase
Neutral
3 wires x 1,5 mm2
4 wires x 0,75 mm2
WARNING : if the awning moves DOWN when pressing the UP button of the RTS controls, invert the brown and black motor wires.
Centralis receiver RTS 2
Mains
CENTRALIS RTS / TELIS
▲▼
N N L
OR
Mains
INIS RT
LT motor
MAIN
SUPPLY
Earth
Phase
Neutral
N
Earth
C Programming :
1 INITIAL INSTALLATION
with an RTS control (Centralis RTS ; TELIS).
Set the CENTRALIS receiver
RTS in its programming
mode by pressing the
PROG button until the LED
lights.
S
E
IS S
MM
33VV IU
IU
HH AATTAA 00
LLITIT EENN 4433
RR RR 22
W CC
MAD
▲▼
N N L
This indicates that the CENTRALIS
receiver RTS is ready to receive the address of a control for
one minute (After this time limit, the LED will go out).
Press shortly the programming
button on the RTS control.
MULTIPLE CONTROL
• Assign several RTS controls to the CENTRALIS receiver RTS following
the same procedure as described above.
You can assign up to 16 controls to one receiver. If you try to enter a
17th, your instruction will be ignored, the led of the receiver will go out.
The LED of the CENTRALIS receiver RTS
blinks indicating that
the address of the RTS
control is memorized
in the receiver which
automatically quits its programming
mode.
GENERAL OR GROUP CONTROL
• Set all the CENTRALIS receiver RTS you wish to control by one RTS
control in their programming mode.
• Press shortly the programming button of the RTS control.
➭ The LEDs of all the CENTRALIS receiver RTS blink indicating that the address of the RTS
control is memorized in all these receivers.
with an INIS RT.
you can only program one INIS RT in the memory of a receiver (single control).
you cannot program INIS RT and RTS controls together in the memory of a receiver.
Set the CENTRALIS receiver RTS in
its programming
mode by pressing
the PROG button
until the LED
lights.
▲▼
N N L
This indicates that the CENTRALIS receiver RTS is
ready to receive the address of a control for one
minute (After this time limit, the LED will go out).
1. remove
the battery
2. press shortly
the push button
3. replace 4. press shortly
the battery the push button
The LED of the
CENTRALIS
receiver RTS
blinks indicating that the
address of the
INIS RT is
memorized in the receiver which automatically quits its programming mode.
2 ADD A NEW CONTROL IN THE MEMORY OF A RECEIVER
(ONLY WITH RTS CONTROL)
S
E
IS S
MM
33VV IU
IU
HH AATTAA 00
LLITIT EENN 4433
RR RR 22
W CC
Press more than 2 seconds on the
programming button of a RTS
control which is already memorized
in the CENTRALIS receiver RTS in
order to “wake up” the receiver.
MAD
➭
➭ the LED of the RTS control lights on, indicating that all the CENTRALIS receivers RTS which
have the adress of this control are in their programming mode for one minute.
Press shortly the
programming button
of the new RTS
control you wish to
assign.
➭ The address of the new
control is memorized in all the CENTRALIS receivers RTS
which automatically quit their programming mode.
3 REMOVE A RTS CONTROL FROM THE MEMORY OF THE RECEIVER
(ON AN EXISTING INSTALLATION)
To remove a RTS control from the memory of a RTS receiver, set the CENTRALIS receiver RTS in its programming mode, then press shortly the
prog button of the RTS control you wish to remove.
It is also possible to “wake up” the CENTRALIS receiver RTS with another RTS control (see § C/2), then press shortly the prog button
of the RTS control you wish to remove.
4 REMOVE ALL THE CONTROLS FROM THE MEMORY OF THE RECEIVER
(RESET OF THE CENTRALIS RECEIVER RTS)
To remove the adresses of all the controls from the memory of a CENTRALIS receiver RTS, press the programming button of the CENTRALIS
receiver RTS until the LED blinks .
➭ The memory of the receiver is erased.
D Intermediate position
(WITH A RTS CONTROL ONLY)
With the CENTRALIS receiver RTS and a RTS control, it is possible to set one or two intermediate positions (IP) : one accessible from the top of the awning (IP1) and one from the bottom (IP2).
To record these positions, the CENTRALIS receiver RTS has to record the time for the awning to go from
its top to the IP and also the time from its bottom one to the IP.
RECORD THE INTERMEDIATE POSITION FROM THE TOP OF THE AWNING
STOP
IP 1
2s
Push the IP
button of the
RTS control
during two seconds.
➭ The CENTRALIS receiver RTS
has memorized the 1st intermediate position.
RECORD THE INTERMEDIATE POSITION FROM THE BOTTOM OF THE AWNING
STOP
IP 2
2s
Set the awning
at its DOWN limit
with the RTS
control.
Push simultaneoustly on the
UP and IP button of the RTS
control until the awning
begins to move (about
three seconds).
REACH THE INTERMEDIATE POSITIONS
IP1 or IP2
To reach one of
the intermediate positions, set
the awning is at
its UP (for IP1) or DOWN (for IP2)
limit, then press briefly the IP button
of the RTS control.
Stop the
awning at the
intermediate
position you
wish with the RTS control
(if necessary, adjust this
position with ▲ and ▼
push buttons).
Push the IP
button of the
RTS control
during two seconds.
➭ The CENTRALIS receiver RTS
has memorized the 2nd intermediate position.
DELETE AN INTERMEDIATE POSITION
To delete an intermediate position,
press briefly the IP button of the RTS
control to reach the intermediate
position you wish to delete, then
press continuoustly the IP button of
the control until the led stops blinking (approx. 8 sec.).
➭ The concerned IP is deleted.
➭ The awning will move and stop at the dedicated intermediate position.
Diagnosis
The LED on the RTS control does not light.
Check the battery of the RTS control.
The led of the RTS control lights, but the motor
does not operate.
1- Press the built-in manual security control of the Centralis receiver RTS.
2- Check the programming.
3- Check the good wiring of the motor and the Centralis receiver RTS.
Non-binding document. Products and references in this document are subject to change without prior notice. Please consult SOMFY before using such references. © SOMFY 12/99
Set the awning at
its UP limit with
the RTS control.
Stop the
awning at the
intermediate
position you
wish with the RTS control
(if necessary, adjust this
position with ▲ and ▼
push buttons).
Push simultaneoustly on the
DOWN and IP
button of the
RTS control until the
awning begins to move
(about three seconds).
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising