Configuration of AIO GATEWAY V5 via ConfigTool NEO

Configuration of AIO GATEWAY V5 via ConfigTool NEO
Configuration of AIO GATEWAY V5 via ConfigTool NEO
If you want to use your AIO GATEWAY V5 in combination with AIO CREATOR NEO, it is necessary to
configure the gateway and connect it to your network. For this purpose you have to use the
ConfigTool NEO.
To download the current Version of the ConfigTool NEO go to this Link:
http://www.mediola.com/downloads.
Please install the program and launch it afterwards.
Note: You can't setup and configure AIO GATEWAYS Version 4 and below via ConfigTool
NEO. For this gateway versions the ConfigTool is required.
1. Setting Up WLAN / Wi-Fi
On the start screen of ConfigTool NEO all already configured gateways are displayed that are found
on the network (the list also contains AIO GATEWAYS versions 4 and below, although they can not be
configured with this program).
To initially configure a new AIO GATEWAY V5 with the ConfigTool NEO click on the button "Add a
Gateway" on the start screen.
© 2016 mediola – connected living AG | Version 06/2016
1
Connect the AIO GATEWAY to a power source. Then click on "Continue".
The RGB LED of the gateway should light in solid orange (access point mode). Now you can connect
your computer to the gateway's own WLAN/ Wifi (not your home WLAN). For this purpose go to the
WLAN/ Wifi settings of your computer and select the network named „AIOGATEWAY–XXXXXX“
(instead of XXXXXX you will see the last digits of the mac address of your gateway). Once your
computer has been connected to this WLAN/ WiFi, click on "Search Gateway".
© 2016 mediola – connected living AG | Version 06/2016
2
If your gateway has been detected, a confirmation will be displayed, containing the name of the
device, the mac address and the current firmware version. Click on "Continue".
In the next step you can select your home WLAN/ Wifi, to connect the gateway to. You also have to
enter the WLAN/ Wifi password. Then click on the "Connect Gateway" button.
The gateway now will try to connect to your home WLAN/ Wifi. During this process the LED flashes
orange until the gateway has connected to the WLAN/ Wifi successfully.
Note: If the LED does not stop flashing, the connection process has failed. In this
case you must reset the gateway (via the reset button on the back) and then
repeat the procedure from the beginning.
When the gateway stops flashing, the setup is finished and the gateway is ready to use.
© 2016 mediola – connected living AG | Version 06/2016
3
By clicking on the button „Open Settings“ you get to the settings page of your AIO GATEWAY.
Note: You always get to the settings page of a gateway, by clicking on the
gateway in the gateway list of the start screen of ConfigTool NEO.
© 2016 mediola – connected living AG | Version 06/2016
4
2. AIO GATEWAY V5 Settings
The following 5 setting categories are provided in the settings menu of your AIO GATEWAY V5:
•
•
•
•
•
General
Network
Cloud Access
Advanced
Debug
To change the gateway setting in one of the categories you previously have to click the "unlock
forms" button.
Note: If a user password has been set in the "Advanced" category, you have to enter the password to
unlock the forms.
© 2016 mediola – connected living AG | Version 06/2016
5
2.1 General
In this category you can set the name of the gateway, the time zone and the geo location. Setting the
right time zone and geo location is important for automations that are time-triggered or triggered by
an event such as sunrise or sunset.
Additionally you get the information about the current firmware version of the gateway, which can
be updated manually.
2.2 Network
In the category Network you can check and modify the network settings of your gateway.
This option should be used only by advanced users with network skills.
2.3 Cloud Access
In the category Cloud Access you can activate/ deactivate and test the option "cloud access" to
control devices via gateway from outside the home network over the Internet.
© 2016 mediola – connected living AG | Version 06/2016
6
Check the mark to activate the cloud access and click "Save" (Important: Don't change the server
settings) Finally click on "Setup". Now the cloud access will be activated.
2.4 Advanced
In the category Advanced you can set a user password for your gateway. If a user password has been
set, you can change settings only by unlocking the forms with the password.
Additionally you can select a sensor mode for your 868 MHz-Chip and the color of the top case RGB
LED.
© 2016 mediola – connected living AG | Version 06/2016
7
Sensor mode:
You can use all supported actuator brands of the 868 MHz band simultaneously, but due to the
modulation characteristics of the 868 MHz band, only sensors of one brand can be used as a trigger
for events or to display a status. Please select which sensor brand you want to use and confirm by
clicking the "save" button.
Note: If 868 MHz sensors from multiple vendors shall be used simultaneously as a trigger, you have
to use a second AIO GATEWAY.
Color of RGB LED:
You can also set the color of the top case LED by entering a hexadecimal color. To turm the LED off
enter 000000.
2.4 Debug
The category Debug shows status messages of your gateway (i.e. to analyze or debug the device).
© 2016 mediola – connected living AG | Version 06/2016
8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising