Installation and Technical Information Small scale floodlight with

Installation and Technical Information Small scale floodlight with
BEGA
Installation and Technical Information
Small scale floodlight with mounting canopy
7601LED.538
Tools Required:
Dimensions
3mm hex key
Flat head screw driver medium
Phillips head screw driver medium
A:
4-1/8 ”
B:
5-7/8 ”
C:
4-3/8 ”
D:
3-1/2 ”
Protection Class: IP65
Weight: 2.0 lbs.
Notice to Installer for 7601LED.538:
Figure 1
1. See page 2 for specific product safety warnings.
2. Mounts directly to 538 small opening wiring box (provided). IMPORTANT: DO NOT MAKE WALL CUTOUT FOR STANDARD WIRING BOX. OPENING MUST BE MADE FOR BEGA 538 WIRING BOX OR CUTOUT WILL BE VISIBLE.
3. In conformance with UL Standard 1598, a silicone based sealant must be used between luminaire and supporting wall.
4. See installation sheet 99068, supplied, for detailed instructions on 538 small wiring box installation.
5. Integral LED driver supplied by BEGA.
7601LED.538 - installation:
1. Remove luminaire mounting plate by loosening 3mm set screw on rear canopy of fixture.
2. Feed luminaire wires through back of luminaire mounting plate.
3. Make supply wiring and luminaire wiring connections inside 538 wiring box:
MAIN VOLTAGE SUPPLY WIRE TO BLACK LUMINAIRE WIRE
NEUTRAL (COMMON) SUPPLY WIRE TO WHITE LUMINAIRE WIRE
GREEN GROUND WIRE TO GREEN LUMINAIRE WIRE
Dimming (if applicable):
DIMMING CONTROL WIRE (+) TO POSITIVE DRIVER DIM CONTROL WIRE
DIMMING CONTROL WIRE (-) TO NEGATIVE DRIVER DIM CONTROL WIRE
4. Attach mounting strap to wiring box using (2) 3/8” screws.
5. Attach mounting plate to mounting strap and wiring box by using (2) 8-32 x 1” mounting screws.
6. Place a small bead of silicone around the back side of the luminaire base that will come in contact with the finished surface.
7. Mount luminaire to mounting plate. Tighten 3mm set screw to secure.
Relamping/Maintenance
Remove trim and lens by loosening screws. Clean
luminaire and lens using only solvent-free cleansers.
Replace trim and lens. Tighten screws.
Lamp: 6.5W LED Module
Figure 2
Accessories
Please refer to the appropriate
accessory installation sheet for
further instruction when applicable.
Small opening wiring box
Floodlight shield
Flatbeam lens
538
755
050
Replacement Parts
Description
Part No
Lens
Lens gasket
140850
831261
LED Gear Tray 3000K
LED Gear Tray 4000K
BP7602K3
BP7602K4
In the interest of product improvement, BEGA reserves the right to make technical changes without notice.
BEGA 1000 Bega Way, Carpinteria, CA 93013 (805)684-0533 Fax (805)566-9474 www.bega-us.com © Copyright BEGA-US 2015
7601LED.538
2/17/2015
Page 1 of 2
BEGA
Installation and Technical Information
Small scale floodlight with mounting canopy
7601LED.538
Product Safety Warnings:
CAUTION - RISK OF FIRE. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND
THE HAZARDS INVOLVED. SUITABLE FOR WET LOCATIONS.
MIN 90°C SUPPLY CONDUCTORS.
ATTENTION - RISQUE D’INCENDIE. CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D’INSTALLATION PERTINENT,
PAR UNE PERSONNE QUI CONNAÎT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES
INHÉRENTS. CONVIENT AUX EMPLACEMENTS MOUILLÉS.
LES FILS D’ALIMENTATION 90°C MIN.
In the interest of product improvement, BEGA reserves the right to make technical changes without notice.
BEGA 1000 Bega Way, Carpinteria, CA 93013 (805)684-0533 Fax (805)566-9474 www.bega-us.com © Copyright BEGA-US 2015
7601LED.538
2/17/2015
Page 2 of 2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising