SN2410 User Manual

SN2410 User Manual
Mellanox 1U Switch Systems Hardware User
Manual
Models: SN2700 and SN2410
Rev 1.2
www.mellanox.com
NOTE:
THIS HARDWARE, SOFTWARE OR TEST SUITE PRODUCT (“PRODUCT(S)”) AND ITS RELATED
DOCUMENTATION ARE PROVIDED BY MELLANOX TECHNOLOGIES “AS-IS” WITH ALL FAULTS OF ANY
KIND AND SOLELY FOR THE PURPOSE OF AIDING THE CUSTOMER IN TESTING APPLICATIONS THAT USE
THE PRODUCTS IN DESIGNATED SOLUTIONS. THE CUSTOMER'S MANUFACTURING TEST ENVIRONMENT
HAS NOT MET THE STANDARDS SET BY MELLANOX TECHNOLOGIES TO FULLY QUALIFY THE PRODUCT(S)
AND/OR THE SYSTEM USING IT. THEREFORE, MELLANOX TECHNOLOGIES CANNOT AND DOES NOT
GUARANTEE OR WARRANT THAT THE PRODUCTS WILL OPERATE WITH THE HIGHEST QUALITY. ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT ARE DISCLAIMED.
IN NO EVENT SHALL MELLANOX BE LIABLE TO CUSTOMER OR ANY THIRD PARTIES FOR ANY DIRECT,
INDIRECT, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES OF ANY KIND (INCLUDING, BUT NOT
LIMITED TO, PAYMENT FOR PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY FROM THE USE OF THE PRODUCT(S) AND RELATED DOCUMENTATION EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Mellanox Technologies
350 Oakmead Parkway Suite 100
Sunnyvale, CA 94085
U.S.A.
www.mellanox.com
Tel: (408) 970-3400
Fax: (408) 970-3403
© Copyright 2016. Mellanox Technologies LTD. All Rights Reserved.
Mellanox®, Mellanox logo, BridgeX®, CloudX logo, Connect-IB®, ConnectX®, CoolBox®, CORE-Direct®, EZchip®,
EZchip logo, EZappliance®, EZdesign®, EZdriver®, EZsystem®, GPUDirect®, InfiniHost®, InfiniScale®, Kotura®, Kotura
logo, Mellanox Federal Systems®, Mellanox Open Ethernet®, Mellanox ScalableHPC®, Mellanox Connect Accelerate
Outperform logo, Mellanox Virtual Modular Switch®, MetroDX®, MetroX®, MLNX-OS®, NP-1c®, NP-2®, NP-3®, Open
Ethernet logo, PhyX®, SwitchX®, Tilera®, Tilera logo, TestX®, The Generation of Open Ethernet logo, UFM®, Virtual
Protocol Interconnect®, Voltaire® and Voltaire logo are registered trademarks of Mellanox Technologies, Ltd.
All other trademarks are property of their respective owners.
For the most updated list of Mellanox trademraks, visit http://www.mellanox.com/page/trademarks
2
Mellanox Technologies
Document Number: MLNX-15-5439
Rev 1.2
Table of Contents
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Chapter 1 Introduction to Mellanox SN2XXX Spectrum™
Ethernet Switch Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.1
1.2
1.3
1.4
1.5
1.6
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speed and Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Management Interfaces and FRUs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ordering Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
12
12
13
13
13
Chapter 2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.1
2.2
2.3
2.4
Safety Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air Flow. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
16
17
18
2.4.1 19” Systems Mounting - Static Rail-Kit for SN2700 . . . . . . . . . . . . . . . . . . . . . . 18
2.4.2 19” Systems Mounting- Telescopic Rail-Kit for SN2700 . . . . . . . . . . . . . . . . . . 23
2.4.3 19” Systems Mounting - Static Rail-Kit for SN2410 . . . . . . . . . . . . . . . . . . . . . . 28
2.5
Cable Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
2.5.1 Breakout Cables and Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
2.6
2.7
Initial Power On. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
System Bring-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
2.7.1 Configuring Network Attributes Using MLNX-OS . . . . . . . . . . . . . . . . . . . . . . . 35
2.7.2 Configuring Network Attributes Using Cumulus Linux. . . . . . . . . . . . . . . . . . . . 40
2.8
FRU Replacements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
2.8.1 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
2.8.2 Fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Chapter 3 Software Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3.1
Upgrading Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3.1.1 MLNX-OS Software Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3.1.2 Cumulus Linux Software Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Chapter 4 Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
4.1
Supported Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
4.1.1
4.1.2
4.1.3
4.1.4
4.1.5
4.1.6
4.2
Data Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RS232 (Console) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
44
44
44
44
45
45
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Mellanox Technologies
3
4.2.1 LED Notifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4.3
Inventory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Chapter 5 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
5.1
Troubleshooting Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Chapter 6 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
6.1
6.2
SN2700 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
SN2410 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Appendix A Accessory and Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Appendix B Thermal Threshold Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Appendix C Interface Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
C.1
C.2
C.3
QSFP Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
SFP+ Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
RJ45 to DB9 Harness Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Appendix D Disassembly and Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
D.1
D.2
Disassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Appendix E Safety Warnings (Multiple Languages) . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
E.1
E.2
E.3
E.4
E.5
E.6
E.7
E.8
E.9
E.10
E.11
E.12
E.13
4
Nordic Countries Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Installation Safety Warnings (English) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
‫( אזהרות בטיחות בהתקנה‬Hebrew) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
安裝安全性警告 (Chinese) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Avertissements de sécurité pour l'installation (French) . . . . . . . . . . . . . . . . . 79
Installation Sicherheitshinweise(German) . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Advertencias de seguridad de instalación (Spanish) . . . . . . . . . . . . . . . . . . . 86
Предупреждения по технике безопасности при установке (Russian) . . . 90
Avertismente privind siguranţa la instalare (Romanian) . . . . . . . . . . . . . . . . 93
Sigurnosna upozorenja za instaliranje (Croatian). . . . . . . . . . . . . . . . . . . . . . 97
Avvertenze di sicurezza per l’installazione (Italian) . . . . . . . . . . . . . . . . . . 101
Montaj Güvenlik Uyarıları (Turkish) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Japan VCCI Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Mellanox Technologies
Rev 1.2
List of Figures
Figure 1:
SN2700 Front Side View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Figure 2:
SN2410 Front Side View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Figure 3:
SN2700 and SN2410 Rear Side View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Figure 4:
Air Flow Direction Marking - Power Side Inlet to Connector Side Outlet . . . . . . . . . . . 17
Figure 5:
Air Flow Direction Marking - Connector Side Inlet to Power Side Outlet . . . . . . . . . . . 17
Figure 6:
Rack Rail Kit Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 7:
Installation Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 8:
Attaching the Rails to the Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 9:
Attaching the Brackets to the Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 10: Installing the Cage Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 11: Attaching the Brackets to the Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 12: Sliding the Blades in the Rails . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 13: Rack Rail Kit Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 14: Rails Separation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 15: Installing the Cage Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Figure 16: Mounting the Outer Rails into the Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Figure 17: Attaching the Inner Rails to the Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 18: Securing the Chassis in the Inner Rails . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 19: Sliding the Switch into the Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 20: Pulling the Unit Outwards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 21: Locking Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Figure 22: Rack Rail Kit Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 23: Installation Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 24: Attaching the Rails to the Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 25: Installing the Cage Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 26: Attaching the Rails to the Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 27: Sliding the Blades in the Rails . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 28: Cable Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 29: Breakout or Fanout Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 30: SN2700 Splitting Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 31: SN2410 Splitting Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Figure 32: System Status LEDs 5 Minutes After Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Figure 33: Two Power Inlets - Electric Caution Notifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Figure 34: PS Unit Pulled Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Figure 35: Fan Module Latches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Mellanox Technologies
5
Figure 36: System Status LEDs - Front and Rear Sides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Figure 37: Fan Status LED - Front and Rear Sides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Figure 38: Power Status LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Figure 39: Rear Side Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Figure 40: SN2700 Port LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Figure 41: SN2410 SFP28 Port LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Figure 42: SN2410 QSFP28 Port LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Figure 43: SN2700 Pull-out Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Figure 44: SN2410 Inventory Information Illustration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Figure 45: QSFP Connector Male and Female Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Figure 46: Rear View of Module With Pin Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Figure 47: RJ45 to DB9 Harness Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
6
Mellanox Technologies
Rev 1.2
List of Tables
Table 1:
Revision History Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Table 2:
References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Table 3:
Speed and Switching Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Table 4:
Management Interfaces and FRUs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Table 5:
Ordering Part Numbers (OPNs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Table 6:
Air Flow Color Legend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Table 7:
Installation Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Table 8:
Installation Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Table 9:
Installation Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table 10:
Serial Terminal Program Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Table 11:
Configuration Wizard Session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Table 12:
Configuration Wizard Session - Static IP Configuration . . . . . . . . . . . . . . . . . . . . . . . . . 38
Table 13:
LEDs Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Table 14:
System Status LED Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Table 15:
Fan Status Front LED Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Table 16:
Fan Status Rear LED Assignments (One LED per Fan) . . . . . . . . . . . . . . . . . . . . . . . . . 48
Table 17:
Power Supply Unit Status Front LED Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Table 18:
Power Supply Unit Status Rear LED Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Table 19:
Bad Port LED Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Table 20:
Port LEDs in Ethernet System Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Table 21:
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Table 22:
SN2700 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Table 23:
SN2410 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Table 24:
OPNs for Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Mellanox Technologies
7
Rev 1.2
Revision History
Table 1 - Revision History Table
Date
Revision
Description
March 2016
1.2
Updated:
•
•
•
•
•
“Introduction to Mellanox SN2XXX Spectrum™ Ethernet Switch Systems”
“Software Management”
“Troubleshooting Instructions”
“Specifications”
“Accessory and Replacement Parts”
Added:
•
8
Taiwan BSMI Class A Statement in “Safety Warnings (Multiple Languages)”
December 2015
1.1
Added SN2410
August 2015
1.0
Initial revision
Mellanox Technologies
Rev 1.2
About this Manual
This manual describes the installation and basic use of the Mellanox Ethernet systems.
Intended Audience
This manual is intended for IT managers and system administrators.
References
Table 2 - References
Document
Description
MLNX-OS® User Manual This document contains information regarding the configuration and management of the MLNX-OS software. See http://www.mellanox.com/page/
mlnx_os.
Cumulus Linux User Guide This document contains information regarding the configuration and management of the Cumulus® Linux® software. See https://docs.cumulusnetworks.com/display/DOCS.
Open Network Install Envi- See https://github.com/opencomputeproject/onie/wiki/Quick-Start-Guide/.
ronment (ONIE) Quick
Start Guide
Conventions
The following icons are used throughout this document to indicate information that is important
to the user.
This icon makes recommendations to the user.
This icon indicates information that is helpful to the user.
Mellanox Technologies
9
Rev 1.2
This icon indicates a situation that can potentially cause damage to hardware or
software.
This icon indicates a situation that can potentially cause personal injury.
10
Mellanox Technologies
Introduction to Mellanox SN2XXX Spectrum™ Ethernet Switch Systems
Rev 1.2
1
Introduction to Mellanox SN2XXX Spectrum™
Ethernet Switch Systems
1.1
Overview
Mellanox Spectrum™ based 1U switch systems are an ideal spine and Top of Rack (ToR) solution, allowing maximum flexibility, with port speeds spanning from 10Gb/s to 100Gb/s per port,
and port density that enables full rack connectivity to any server at any speed. The uplink ports
allow a variety of blocking ratios that suit any application requirement. Powered by the Spectrum
ASIC, the systems carry whopping switching and processing capacities in a compact 1U form
factor.
Keeping with the Mellanox tradition of setting performance record switch systems, the Spectrum
based systems introduce the world’s lowest latency for 100GbE switching and routing elements,
and do so while having the lowest power consumption in the market. They enable the use of 10,
25, 40, 50 and 100GbE in a large scale without changing power infrastructure facilities.
The Spectrum™ based 1U switch systems are a part of Mellanox’s complete end-to-end solution,
which provides 10GbE through 100GbE interconnectivity within the data center. Other devices
in this solution include ConnectX-4 based network interface cards, and LinkX copper or fiber
cabling. This end-to-end solution is topped with NEO, a management application that relieves
some of the major obstacles standing in the way when deploying a network. NEO enables a fully
certified and interoperable design, speeds up time to service and RoI. The systems introduce
hardware capabilities for multiple tunneling protocols that enable increased reachability and scalability for today’s data centers. Implementing MPLS, NVGRE and VXLAN tunneling encapsulations in the network layer of the data center allows more flexibility for terminating a tunnel by
the network, in addition to termination on the server endpoint.
While Spectrum provides the thrust and acceleration that powers the switch systems, they get yet
another angle of capabilities, running with a powerful x86-based processor, which allows them to
not only be the highest performing switch fabric elements, but also grants them the ability to
incorporate a Linux running server into the same device. This opens up multiple application
aspects of utilizing the high CPU processing power and the best switching fabric, to create a
powerful machine with unique appliance capabilities that can improve numerous network implementation paradigms.
The Spectrum™ based 1U switch systems support the Open Network Install Environment
(ONIE) for zero touch installations of network operating systems. While all Ethernet systems can
be purchased preloaded with Mellanox-OS, the SN2700 and SN2410 switches (in both the
100GbE and the 40GbE versions) are offered, in addition, with Cumulus Linux support, as an
alternative operating system. For a full list of all available ordering options, see “Ordering Information”.
Mellanox Technologies
11
Rev 1.2
Introduction to Mellanox SN2XXX Spectrum™ Ethernet Switch Systems
Figure 1: SN2700 Front Side View
Figure 2: SN2410 Front Side View
Figure 3: SN2700 and SN2410 Rear Side View
1.2
Speed and Switching
Table 3 describes maximum throughput and interface speed per system model.
Table 3 - Speed and Switching Capabilities
System Model
40/50/56/100GbE
QSFP28 Interfaces*
10/25GbE SFP28 Interfaces*
Max Throughput
SN2700
64 (using QSFP to SFP breakout
cables)
32
6.4Tb/s
SN2410
Total 64, 48zSFP+ 16 (using
QSFP to SFP breakout cables)
8
4Tb/s
*The system can support different interfaces and speed rates using QSFP to SFP adapters or hybrid cables. For further information,
see “Breakout Cables and Adapters”.
1.3
Management Interfaces and FRUs
Table 4 lists the various management interfaces and available replacement parts per system
model.
Table 4 - Management Interfaces and FRUs
System Model
12
USB
MGT
Console
Replaceable
PSU
Replaceable
Fan
SN2700
Rear
Rear (2 ports)
Rear
2 units
4 units
SN2410
Rear
Rear (2 ports)
Rear
2 units
4 units
Mellanox Technologies
Introduction to Mellanox SN2XXX Spectrum™ Ethernet Switch Systems
1.4
Rev 1.2
Features
For a full feature list, please refer to the system’s product brief. Go to http://www.mellanox.com.
In the main menu, click on Products--> Ethernet Switch Systems, and select the desired product
page.
1.5
Certifications
The list of certifications (such as EMC, Safety and others) per system for different regions of the
world is located on the Mellanox website at:
http://www.mellanox.com/page/environmental_compliance.
1.6
Ordering Information
The following table lists ordering information for the available systems. Please pay attention to
the airflow direction when ordering your system. For more details, see “Air Flow”.
Table 5 - Ordering Part Numbers (OPNs)
System
Model
SN2700
OPN
Description
MSN2700-CS2F
Spectrum™ based 100GbE 1U Open Ethernet Switch with MLNXOS, 32 QSFP28 ports, 2 Power Supplies (AC), Standard depth, x86
CPU, P2C airflow, Rail Kit, RoHS6
MSN2700-CS2R
Spectrum™ based 100GbE 1U Open Ethernet Switch with MLNXOS, 32 QSFP28 ports, 2 Power Supplies (AC), Standard depth, x86
CPU, C2P airflow, Rail Kit, RoHS6
MSN2700-CS2FO
Spectrum™ based 100GbE 1U Open Switch with ONIE, 32
QSFP28 ports, 2 Power Supplies (AC), Standard depth, x86 CPU,
P2C airflow, Rail Kit, RoHS6
MSN2700-BS2F
Spectrum™ based 40GbE, 1U Open Ethernet Switch with MLNXOS, 32 QSFP28 ports, 2 Power Supplies (AC), x86 CPU, Standard
depth, P2C airflow, Rail Kit, RoHS6
MSN2700-BS2FC
Spectrum™ based 40GbE, 1U Open Ethernet Switch with Cumulus
Linux, 32 QSFP28 ports, 2 Power Supplies (AC), Standard depth,
x86 CPU, P2C airflow, Rail Kit, RoHS6
MSN2700-BS2RC
Spectrum™ based 40GbE, 1U Open Ethernet Switch with Cumulus
Linux, 32 QSFP28 ports, 2 Power Supplies (AC), Standard depth,
x86 CPU, C2P airflow, Rail Kit, RoHS6
MSN2700-CS2FC
Spectrum™ based 100GbE 1U Open Ethernet Switch with Cumulus Linux, 32 QSFP28 ports, 2 Power Supplies (AC), Standard
depth, x86 CPU, P2C airflow, Rail Kit, RoHS6
MSN2700-CS2RC
Spectrum™ based 100GbE 1U Open Ethernet Switch with Cumulus Linux, 32 QSFP28 ports, 2 Power Supplies (AC), Standard
depth, x86 CPU, C2P airflow, Rail Kit, RoHS6
Mellanox Technologies
13
Rev 1.2
Introduction to Mellanox SN2XXX Spectrum™ Ethernet Switch Systems
Table 5 - Ordering Part Numbers (OPNs)
System
Model
SN2410
14
OPN
Description
MSN2410-CB2F
Spectrum™ based 25GbE/100GbE 1U Open Ethernet switch with
MLNX-OS, 48 SFP28 ports, 8 QSFP28 ports, 2 power supplies
(AC), x86 dual core, Short depth, P2C airflow, Rail Kit, RoHS6
MSN2410-BB2F
Spectrum™ based 10GbE/100GbE 1U Open Ethernet switch with
MLNX-OS, 48 SFP28 ports, 8 QSFP28 ports, 2 power supplies
(AC), x86 dual core, Short depth, P2C airflow, Rail Kit, RoHS6
MSN2410-BB2FC
Spectrum™ based 10GbE/100GbE 1U Open Ethernet switch with
Cumulus Linux, 48 SFP28 ports, 8 QSFP28 ports, 2 power supplies
(AC), x86 dual core, Short depth, P2C airflow, Rail Kit, RoHS6
MSN2410-BB2RC
Spectrum™ based 10GbE/100GbE 1U Open Ethernet switch with
Cumulus Linux, 48 SFP28 ports, 8 QSFP28 ports, 2 power supplies
(AC), x86 dual core, Short depth, C2P airflow, Rail Kit, RoHS6
MSN2410-CB2FC
Spectrum™ based 25GbE/100GbE 1U Open Ethernet switch with
Cumulus Linux, 48 SFP28 ports, 8 QSFP28 ports, 2 power supplies
(AC), x86 dual core, Short depth, P2C airflow, Rail Kit, RoHS6
MSN2410-CB2RC
Spectrum™ based 25GbE/100GbE 1U Open Ethernet switch with
Cumulus Linux, 48 SFP28 ports, 8 QSFP28 ports, 2 power supplies
(AC), x86 dual core, Short depth, C2P airflow, Rail Kit, RoHS6
Mellanox Technologies
Installation
2
Rev 1.2
Installation
Installation and initialization of the system require attention to the normal mechanical, power,
and thermal precautions for rack-mounted equipment.
The rack mounting holes conform to the EIA-310 standard for 19-inch racks. Take
precautions to guarantee proper ventilation in order to maintain good airflow at ambient temperature.
 The installation procedure for the system involves the following phases:
1. Follow the safety warnings in Section 2.1.
2. Pay attention to the air flow consideration within the system and rack - refer to “Air Flow” on
page 16.
3. Make sure that none of the package contents is missing or damaged - see “Package Contents”
on page 17.
4. Mount the system into a rack enclosure - see “Mounting Options” on page 18.
5. Power on the system - refer to “Initial Power On” on page 34.
6. Perform system bring-up - see “System Bring-Up” on page 35.
FRU replacements are described in Section 2.8 on page 40.
2.1
Safety Warnings
Prior to the installation, please review the safety warnings as follows:
•
For Nordic Countries Notices, see Section E.1, “Nordic Countries Notices,” on page 67.
•
For Safety Warnings in English, see Section E.2, “Installation Safety Warnings
(English),” on page 67.
•
For Safety Warnings in Hebrew, see Section E.3, “‫( אזהרות בטיחות בהתקנה‬Hebrew),” on
page 70.
•
For Safety Warnings in Chinese, see Section 1 on page 74.
•
For Safety Warnings in French, see Section E.5, “Avertissements de sécurité pour
l'installation (French),” on page 79.
•
For Safety Warnings in German, Section E.6, “Installation Sicherheitshinweise(German),” on page 82.
•
For Safety Warnings in Spanish, see Section E.7, “Advertencias de seguridad de instalación (Spanish),” on page 86.
•
For Safety Warnings in Russian, see Section E.8, “Предупреждения по технике
безопасности при установке (Russian),” on page 90.
•
For Safety Warnings in Romanian, see Section E.9, “Avertismente privind siguranţa la
instalare (Romanian),” on page 93.
•
For Safety Warnings in Croatian, see Section E.10, “Sigurnosna upozorenja za instaliranje (Croatian),” on page 97.
Mellanox Technologies
15
Rev 1.2
2.2
Installation
•
For Safety Warnings in Italian, see Section E.11, “Avvertenze di sicurezza per
l’installazione (Italian),” on page 101.
•
For Safety Warnings in Turkish see Section E.12, “Montaj Güvenlik Uyarıları (Turkish),” on page 105.
Air Flow
Mellanox systems are offered with two air flow patterns:
•
Power (rear) side inlet to connector side outlet - marked with blue power supplies/fansFRUs’ handles, as shown in Figure 4.
•
Connector (front) side inlet to power side outlet - marked with red power supplies/fans
FRUs’ handles, as shown in figure Figure 5.
All servers and systems in the same rack should be planned with the same airflow
direction.
All FRU components need to have the same air flow direction. A mismatch in the air
flow will affect the heat dissipation.
Table 6 provides an air flow color legend and respective OPN designations.
Table 6 - Air Flow Color Legend
Direction
16
Mellanox Technologies
OPN
Designation
Description
Ending with
“-R”
Connector side inlet to power side outlet.
Red latches are placed on the power inlet
side.
Ending with
“-F”
Power side inlet to connector side outlet.
Blue latches are placed on the power inlet
side.
Installation
Rev 1.2
Figure 4: Air Flow Direction Marking - Power Side Inlet to Connector Side Outlet
Figure 5: Air Flow Direction Marking - Connector Side Inlet to Power Side Outlet
2.3
Package Contents
Before installing your new system, unpack it and check against the parts list below that all the
parts have been sent. Check the parts for visible damage that may have occurred during shipping.
The SN2700 and SN2410 package content is as follows:
•
1 – System
•
1 – Rail kit
•
1 – Power cable for each power supply unit – Type C13-C14
•
1 – Cable retainer for each power supply unit
•
1 – DB9 to RJ-451 2m harness
Mellanox Technologies
17
Rev 1.2
2.4
Installation
Mounting Options
If anything is damaged or missing, contact your sales representative at support@mellanox.com.
By default, the SN2700 system is sold with the Static Rail-kit described in Section 2.4.1. The
SN2410 system is sold with the Static Rail-kit described in Section 2.4.3. For the Telescopic
Rail-kit installation instructions, (can be used with SN2700 only) see Section 2.4.2.
2.4.1
19” Systems Mounting - Static Rail-Kit for SN2700
At least two people are required to safely mount the system in the rack.
The following parts are included in the Static Rail kit (see Figure 6):
Table 7 - Installation Kit
Kit OPN
Rack Size and Rack Depth Range
MTEF-KIT-A
Short (17”-24”) or Standard (24”-34”)
•
2x Rack mount rails (A)
•
2x Rack mount brackets (B)
•
2x Rack mount blades (C)
•
8x M6 Standard cage nuts¹ ² and 8x M6 Standard pan-head Phillips screws¹ (D)
•
4x Phillips100 DEG F.H TYPE-I ST.ST 6-32 X 1/4 screw with around patch (E)
¹ Other threads are available by special order: M5, 10-32, 12-24
² G-type cage-nut is available by special order.
18
Mellanox Technologies
Installation
Rev 1.2
Figure 6: Rack Rail Kit Parts
 To mount the system into the rack:
Before mounting the system to the rack, select the way you wish to place the system. Pay attention to the airflow within the rack cooling, connector and cabling options.
While planning how to place the system, consider the two installation options shown in Figure 7,
and review the following points:
•
Make sure the system air flow is compatible with your installation selection. It is
important to keep the airflow within the rack in the same direction.
•
Note that the part of the system to which you choose to attach the rails (the front panel
direction, as demonstrated in Option 1 or the FRUs direction, as demonstrated in Option
2) will determine the system’s adjustable side. The system’s part to which the brackets
are attached will be adjacent to the cabinet.
•
The FRU side is extractable. Mounting the rack brackets inverted to the FRU side
(Option 2) will allow you to slide the FRUs, in and out.
Mellanox Technologies
19
Rev 1.2
Installation
Figure 7: Installation Options
Step 1.
Attach the left and right rack mount rails (A) to the switch, by gently pushing the switch chassis’ pins through the slider key holes, until locking occurs.
Step 2.
Secure the chassis in the rails by screwing 2 flat head Phillips screws (E) in the designated
points with a torque of 1.5±0.2 Nm. See Figure 8.
Figure 8: Attaching the Rails to the Chassis
Step 3.
20
Attach the left and right rack mount brackets (B) to the switch, by gently pushing the switch
chassis’ pins through the slider key holes, until locking occurs. Secure the system in the brackets by screwing the remaining 2 flat head Phillips screws (E) in the designated points with a
torque of 1.5±0.2 Nm. See Figure 9.
Mellanox Technologies
Installation
Rev 1.2
Figure 9: Attaching the Brackets to the Chassis
Step 4.
Install 8 cage nuts in the desired 1U slots of the rack: 4 cage nuts in the non-extractable side (in
the top and bottom holes only) and 4 cage nuts in the extractable side.
Figure 10: Installing the Cage Nuts
While each rack U (unit) consists of three holes, the cage nut should be installed vertically with its ears engaging the top and bottom holes only.
While your installation partner is supporting the system’s weight, perform the following steps:
Step 5.
Mount the system into the rack enclosure, and attach the brackets installed on the system to the
rack’s posts. Secure the brackets to the rack’s posts by inserting four M6 screws in the designated cage nuts, as described in Figure 11. Do not tighten the screws yet.
Mellanox Technologies
21
Rev 1.2
Installation
Figure 11: Attaching the Brackets to the Rack
Step 6.
Slide the two blades into the left and right rails, and adjust them to fit your rack's depth. Use
four M6 screws (D) to fix the blades into the rack. Do not tighten the screws yet.
Figure 12: Sliding the Blades in the Rails
Step 7.
Secure the system in the rack by tightening the 8 screws inserted in Step 5 and Step 6 with a
torque of 4.5±0.5 Nm.
2.4.1.1 Removing the System from the Rack
 To remove a unit from the rack:
Step 1.
Turn off the system and disconnect it from peripherals and from the electrical outlet.
While your installation partner is supporting the system’s weight:
22
Step 2.
Loosen the screws attaching the brackets to the rack. Do not remove them yet.
Step 3.
Loosen the screws attaching the blades to the rack, and pull the blades towards you, while your
partner is holding the system.
Step 4.
Extract the loosened screws from Step 2 and dismount the system from the rack.
Step 5.
Remove the rails and brackets from the chassis by unscrewing 8 screws.
Mellanox Technologies
Installation
2.4.2
Rev 1.2
19” Systems Mounting- Telescopic Rail-Kit for SN2700
Note: the Telescopic Rail-Kit is not included in the system’s package, and can be purchased separately.
There are two installation kit options:
•
Standard depth systems should be mounted using the standard rail kit.
•
Short depth systems can be mounted using either of the rail kits.
The following parts are included in the rail kit package (see Figure 13):
Table 8 - Installation Kit
Kit OPN
Rack Size and Rack Depth Range
MTEF-KIT-B
Short (17"-24" \ 43.1 to 61 cm)
MTEF-KIT-S
Standard (24"-34" \ 61 to 86.3 cm)
•
1x Right inner rail (A)
•
1x Left inner rail (B)
•
2x Outer rails (C)
•
2x Outer rails (D)
•
10x M6 Standard cage nuts¹ ² and 10x M6 Standard pan-head Phillips screws¹ (E)
•
2x Phillips100 DEG F.H TYPE-I ST.ST 6-32 X 1/4 screw with around patch (F)
¹ Other threads are available by special order: M5, 10-32, 12-24
² G-type cage-nut is available by special order.
The rails must be separated prior to the installation procedure. See Figure 14.
Mellanox Technologies
23
Rev 1.2
Installation
Figure 13: Rack Rail Kit Parts
Figure 14: Rails Separation
To separate the rails:
1. Extend the rail assembly by pulling the extension outwards (D).
2. Extract rail A from rail C by pushing it outside from the rear part of the assembly. To allow complete separation of rail A from rail C, press the quick-release latch.
24
Mellanox Technologies
Installation
Rev 1.2
Before mounting the system to the rack, select the way you wish to place the system. Pay attention to the airflow within the rack cooling, connector and cabling options.
While planning how to place the system, review the following points:
•
Make sure the system air flow is compatible with your installation selection. It is
important to keep the airflow within the rack in the same direction.
•
In case there are cables that cannot bend within the rack, or in case more space is
needed for cable bending radius, it is possible to recess the connector side or the FRU
side by 3” or 4” (7.62 or 10.16cm) by optional placement of the system’s rails.
•
The FRU side is extractable. Mounting the sliding rail inverted to the system will allow
you to slide the FRU side of the system, in and out.
Step 1.
Install 10 cage nuts into the desired 1U slots of the rack: 4 cage nuts in the non-extractable side
and 6 cage nuts in the extractable side.
Figure 15: Installing the Cage Nuts
Step 2.
Mount both of the outer rails (C+D) into the rack (as illustrated in Figure 16), and use 8 standard pan-head screws (E) to fix them to the rack. Do not tighten the screws yet.
Figure 16: Mounting the Outer Rails into the Rack
Step 3.
If cable accommodation is required, route the power cable and/or Eth cable through either of
the outer rails.
Step 4.
Attach the switch to the left and right inner rails (A+B), by gently pushing the switch chassis’
pins through the slider key holes, until locking occurs.
Mellanox Technologies
25
Rev 1.2
Installation
Figure 17: Attaching the Inner Rails to the Chassis
Step 5.
Secure the chassis in the inner rails by screwing the 2 flat head Phillips screws (F) in the designated points with a torque of 1.5±0.2 Nm.
Figure 18: Securing the Chassis in the Inner Rails
Step 6.
26
Slide the switch into the rack by carefully pushing the inner rails into the outer rails installed on
the rack.
Mellanox Technologies
Installation
Rev 1.2
Figure 19: Sliding the Switch into the Rack
Step 7.
When fully inserted, fix the switch by closing the remaining 2 screws in the middle and tightening the 8 screws inserted in Step 2 with a torque of 4.5±0.5 Nm.
2.4.2.1 Removing the System from the Rack
 To remove a unit from the rack:
Step 1.
Turn off the system and disconnect it from peripherals and from the electrical outlet.
Step 2.
Unscrew the two M6 screws securing the front of the inner rails’ ears to the outer rails and to
the rack.
Step 3.
Pull the unit out until braking is felt. For safety purposes, the locking mechanism will not allow
a complete removal of the unit at this stage.
Figure 20: Pulling the Unit Outwards
Mellanox Technologies
27
Rev 1.2
Installation
Step 4.
Press on the locking spring (appears in red in Figure 21) on both sides simultaneously, and continue pulling the unit towards you until it is fully removed.
Figure 21: Locking Mechanism
2.4.3
19” Systems Mounting - Static Rail-Kit for SN2410
At least two people are required to safely mount the system in the rack.
Note: By default, the system is sold with the Standard-depth Rail Kit. The Shortdepth Rail Kit can be supplied upon request.
The following parts are included in the Static Rail kit (see Figure 6):
Table 9 - Installation Kit
28
Kit OPN
Rack Size and Rack Depth Range
MTEF-KIT-BP
Short (15.7"-23.6" \ 40 to 60 cm)
MTEF-KIT-SP
Standard (23.6"-31.5" \ 60 to 80 cm)
•
2x Rack mount rails (A)
•
2x Rack mount blades (B)
•
8x M6 Standard cage nuts¹ ² and 8x M6 Standard pan-head Phillips screws¹ (C)
Mellanox Technologies
Installation
Rev 1.2
•
4x Phillips100 DEG F.H TYPE-I ST.ST 6-32 X 1/4 screw with around patch (D).
¹ Other threads are available by special order: M5, 10-32, 12-24
² G-type cage-nut is available by special order.
Figure 22: Rack Rail Kit Parts
Before mounting the system to the rack, select the way you wish to place the system. Pay attention to the airflow within the rack cooling, connector and cabling options.
While planning how to place the system, consider the two installation options shown in
Figure 23, and review the following points:
•
Make sure the system air flow is compatible with your installation selection. It is
important to keep the airflow within the rack in the same direction.
•
Note that the part of the system to which you choose to attach the rails (the front panel
direction, as demonstrated in Option 1 or the FRUs direction, as demonstrated in Option
2) will determine the system’s adjustable side. The system’s part to which the blades are
attached, will be adjacent to the cabinet.
•
In case there are cables that cannot bend within the rack, or in case more space is
needed for cable bending radius, it is possible to recess the connector side or the FRU
side by 3.5" (8.9 cm), by optional placement of the system’s rails.
•
The FRU side is extractable. Mounting the rack blades inverted to the FRU side (Option
2) will allow you to slide the FRUs, in and out.
Mellanox Technologies
29
Rev 1.2
Installation
Figure 23: Installation Options
Step 1.
Attach the left and right rack mount rails (A) to the switch, and secure the chassis in the rails by
screwing 2 flat head Phillips screws (D) in the designated points on each side (a total of 4
screws). See Figure 24. To tighten the screws, use a torque of 1.5±0.2 Nm.
Figure 24: Attaching the Rails to the Chassis
Step 2.
30
Install 8 cage nuts (C) in the desired 1U slots of the rack: 4 cage nuts in the non-extractable side
and 4 cage nuts in the extractable side. Note that while each rack U (unit) consists of three
holes, the cage nut should be installed vertically with its ears engaging the top and bottom holes
only. See Figure 25.
Mellanox Technologies
Installation
Rev 1.2
Figure 25: Installing the Cage Nuts
While your installation partner is supporting the system’s weight, perform steps 3, 4 and 5:
Step 3.
On the rear side of the cabinet, install the two blades (B) in the selected rack unit, using four
M6 screws (C). Do not tighten the screws yet. See Figure 26.
Figure 26: Attaching the Rails to the Rack
Step 4.
Slide the two blades into the left and right rails, and adjust them to fit your rack's depth. Use
four M6 screws (D) to fix the blades into the rack. Do not tighten the screws yet. See Figure 27.
Figure 27: Sliding the Blades in the Rails
Step 5.
Secure the system in the rack by tightening the 8 screws inserted in Step 3 and Step 4 with a
torque of 4.5±0.5 Nm.
Mellanox Technologies
31
Rev 1.2
2.5
Installation
Cable Installation
All cables can be inserted or removed with the unit powered on.
To insert a cable, press the connector into the port receptacle until the connector is firmly seated.
The LED indicator, corresponding to each data port, will light when the physical connection is
established. When a logical connection is made, the relevant port LED will turn on.
To remove a cable, disengage the locks and slowly pull the connector away from the port receptacle. The LED indicator for that port will turn off when the cable is unseated.
For full cabling guidelines, ask your Mellanox representative for a copy of Mellanox Cable Management Guidelines and FAQ.
For more information about port LEDs, refer to “Port LEDs”.
Do not force the cable into the cage with more than 40 newtons / 9.0 pounds / 4kg
force. Greater insertion force may cause damage to the cable or to the cage.
Figure 28: Cable Orientation
2.5.1
Breakout Cables and Adapters
A 100GbE port can be split to two 50GbE ports, or to four (or less) 25GbE ports, using a Mellanox breakout cable.
Splitting a 100GbE QSFP28 port to 4 separate 25GbE ports (using a breakout cable) disables
(unmaps) the 100GbE port below it. See Figure 30,“SN2700 Splitting Options”.
2.5.1.1 Using Breakout Cables with MLNX-OS
When using this feature, you should log into the MLNX-OS® CLI and configure the individual
ports to be ‘split-2’ or ‘split-4’. For further information on Mellanox’s cable, visit http://
www.mellanox.com/page/interconnect_overview.
32
Mellanox Technologies
Installation
Rev 1.2
2.5.1.2 Using Breakout Cables with Cumulus Linux
If you are using 4x10G direct attach copper cables or active optical cables, edit the /etc/cumulus/ports.conf to enable support for these cables, then restart the switchd service using the
sudo systemctl restart switchd command. For more details, see Layer 1 and Switch
Port Attributes in the Cumulus Linux User Guide.
Figure 29: Breakout or Fanout Cables
2.5.1.3 SN2700 Splitting Options
Figure 30: SN2700 Splitting Options
The top QSFP ports marked in green are splittable to 4 SFP ports, each. The bottom QSFP ports
(gray) are blocked when the upper ports are in split mode. All QSFP ports marked in yellow can
be split to 2 SFP ports.
Mellanox Technologies
33
Rev 1.2
Installation
2.5.1.4 SN2410 Splitting Options
Figure 31: SN2410 Splitting Options
The top QSFP28 ports - 49,51,53,55 (green) are splittable to 4 SFP28 ports each.
All QSFP28 ports can be split into two SFP28 ports.
The bottom QSFP28 ports - 50,52,54,56 (gray) are blocked when the upper ports are in split
mode.
2.6
Initial Power On
Each system’s input voltage is specified in the “Specifications” chapter. The power cords should
be standard 3-wire AC power cords including a safety ground and rated for 15A or higher.
The system platform will automatically power on when AC power is applied. There is
no power system. Check all boards, power supplies, and fan tray modules for proper
insertion before plugging in a power cable.
Step 1.
Plug in the first power cable.
Step 2.
Plug in the second power cable.
Step 3.
Wait for the system upload process.
It may take up to five minutes to turn on the system. If the System Status LED shows
red after five minutes, unplug the system and call your Mellanox representative for
assistance.
Step 4.
34
Check the System Status LEDs and confirm that all of the LEDs show status lights consistent
with normal operation (initially flashing, and then moving to a steady color) as shown in
Figure 32 below. For more information, refer to “LEDs”.
Mellanox Technologies
Installation
Rev 1.2
Figure 32: System Status LEDs 5 Minutes After Power On
After inserting a power cable and confirming the green System Status LED light is
on, make sure that the Fan Status LED shows green.
If the Fan Status LED is not green, unplug the power connection and check that the
fan module is inserted properly and that the mating connector of the fan unit is free of
any dirt and/or obstacles. If no obstacles were found and the problem persists, call
your Mellanox representative for assistance.
Figure 33: Two Power Inlets - Electric Caution Notifications
CAUTION
Risk of electric shock and energy
hazard. The two power supply
units are independent.
Disconnect all power supplies to
ensure a powered down state
inside of the switch platform.
2.7
ACHTUNG
Gafahr des elektrischen
Schocks. Entferrnen des
Netzsteckers elnes Netzteils spannungsfrei. Um
alle Einhieten spannungsfrei zu machen sind die
Netzstecker aller Netzteile
zu entfernen
ATTENTION
Risque de choc et de danger
e’lectriques. Le de’branchment d’une seule alimentation
stabilise’e ne de’branch
uniquement qu’un module
“Alimentation Stabilise’e”.
Pour isoler completement le
module en cause, Il faut
de’brancher toutes les alimentations stabilise’es.
System Bring-Up
Section 2.7.1 describes bring-up of a switch system with the MLNX-OS operating system
installed.
Section 2.7.2 describes bring-up of a switch system with the Cumulus Linux operating system
installed.
2.7.1
Configuring Network Attributes Using MLNX-OS
The procedures described in this chapter assume that you have already installed and powered-on
the system according to the instructions in this document. Since the system comes with a preconfigured DHCP, you may find the explanation in Section 2.7.1.1 sufficient. In case a manual
configuration is required, please refer to the instructions in Section 2.7.1.2.
Mellanox Technologies
35
Rev 1.2
Installation
2.7.1.1 Disable Dynamic Host Configuration Protocol (DHCP)
DHCP is used for automatic retrieval of management IP addresses.
If a user connects through SSH, runs the wizard and turns off DHCP, the connection is
immediately terminated, as the management interface loses its IP address.
<localhost># ssh admin@<ip-address>
Mellanox MLNX-OS Switch Management
Password:
Mellanox Switch
Mellanox configuration wizard
Do you want to use the wizard for initial configuration?
yes
Step 1: Hostname? [my-switch]
Step 2: Use DHCP on mgmt0 interface? [yes] no
<localhost>#
In such case the serial connection should be used.
2.7.1.2 Manual Host Configuration
 To perform initial configuration of the system:
Step 1.
Connect a host PC to the Console RJ45 (
) port of the system, using the supplied harness
cable (DB9 to RJ45). Make sure to connect to the Console RJ45 port and not to the (Ethernet)
MGT port.
Step 2.
Configure a serial terminal program (for example, HyperTerminal, minicom, or Tera Term) on
your host PC with the settings described in Table 10. Once you perform that, you should get the
CLI prompt of the system.
Table 10 - Serial Terminal Program Configuration
Setting
Parameter
36
Baud Rate
115200
Data bits
8
Stop bits
1
Parity
None
Flow Control
None
Step 3.
Login as admin and use admin as password. On the first login, the MLNX-OS configuration
wizard will start.
Step 4.
To configure network attributes and other initial parameters to the system, follow the configuration wizard as shown in Table 11.
Mellanox Technologies
Installation
Rev 1.2
Table 11 - Configuration Wizard Session
Wizard Session Display
Comments
Mellanox configuration wizard
Do you want to use the wizard
for initial configuration? yes
You must perform this configuration the first time you operate the
system or after resetting the system. Type ‘y’ and then press
<Enter>.
Step 1: Hostname? [switch-1]
If you wish to accept the default hostname, press <Enter>. Otherwise, type a different hostname and press <Enter>.
Step 2: Use DHCP on mgmt0
interface? [no] yes
Perform this step to obtain an IP address for the system. (mgmt0 is
the management port of the system).
If you wish the DHCP server to assign the IP address, type ‘yes’
and press <Enter>.
If you type ‘no’ (no DHCP), then you will be asked whether you
wish to use the ‘zeroconf’ configuration or not.
If you enter ‘no’ (no Zeroconf), you must enter a static IP, and the
session will continue.
Step 3: Enable IPv6? [yes]
The management interface will be able to use IPv6 addresses.
If you enter "no" (no IPv6), you will automatically be referred to
Step 6.
Step 4: Enable IPv6 auto-config This turns on auto-configuration of the IPv6 addresses. This is
(SLAAC) on mgmt0 interface? unsuitable for DHCPv6.
[no]
Step 5: Enable DHCPv6 on
mgmt0 interface? [no]
To enable DHCPv6 on the MGMT0 interface.
Step 6: Admin password (Press
<Enter> to leave unchanged)?
<new_password>
Step 6: Confirm admin password? <new_password>
To avoid illegal access to the machine, please type a password and
then press <Enter>. Then confirm the password by re-entering it.
You have entered the following
information:
The wizard displays a summary of your choices and then asks you
to confirm the choices or to re-edit them.
<A summary of the configuration is now displayed.>
To change an answer, enter the
step number to return to or hit
<enter> to save changes and exit.
Choice: <Enter>
Configuration changes saved.
Either press <Enter> to save changes and exit, or enter the configuration step number that you wish to return to.
Note that password characters are not printed.
Note:
To re-run the configuration wizard, run the command “configuration jump-start” in Config mode.
Mellanox Technologies
37
Rev 1.2
Installation
The table below shows an example of static IP configuration for mgmt0 interface.
Table 12 - Configuration Wizard Session - Static IP Configuration
Wizard Session Display - Static IP Configuration (Example)
Mellanox configuration wizard
Do you want to use the wizard for initial configuration? yes
Step 1: Hostname? []
Step 2: Use DHCP on mgmt0 interface? [yes] no
Step 3: Use zeroconf on mgmt0 interface? [no]
Step 4: Primary IP address? [for example 192.168.10.4] 10.10.10.10
Mask length may not be zero if address is not zero (interface eth0)
Step 5: Netmask? [0.0.0.0] 255.255.255.0
Step 6: Default gateway? [for example 192.168.10.1] 10.10.10.255
Step 7: Primary DNS server?
Step 8: Domain name?
Step 9: Enable IPv6? [yes]
Step 10: Enable IPv6 autoconfig (SLAAC) on mgmt0 interface? [no]
Step 11: Admin password (Enter to leave unchanged)?
To change an answer, enter the step number to return to.
Otherwise hit <enter> to save changes and exit.
Choice:
Configuration changes saved.
To return to the wizard from the CLI, enter the “configuration jump-start”
command from configure mode. Launching CLI...
>
38
Mellanox Technologies
Installation
Rev 1.2
Step 5.
Before attempting a remote (for example, SSH) connection to the system, check the mgmt0
interface configuration. Specifically, verify the existence of an IP address. To check the current
mgmt0 configuration, enter the following command:
r-qa-sit-switch01 (config) # show interfaces mgmt0
Interface mgmt0 status:
Comment:
Admin up:
yes
Link up:
yes
DHCP running:
yes
IP address:
192.168.1.100
Netmask:
255.255.255.0
IPv6 enabled:
yes
Autoconf enabled: no
Autoconf route:
yes
Autoconf privacy: no
DHCPv6 running:
no
IPv6 addresses:
1
IPv6 address:
fe80::202:c9ff:fe63:b55a/64
Speed:
1000Mb/s (auto)
Duplex:
full (auto)
Interface type:
ethernet
Interface source: physical
MTU:
1500
HW address:
00:02:C9:63:B5:5A
RX
RX
RX
RX
RX
RX
RX
bytes:
packets:
mcast packets:
discards:
errors:
overruns:
frame:
968810197
10982099
0
0
0
0
0
TX
TX
TX
TX
TX
TX
TX
TX
bytes:
packets:
discards:
errors:
overruns:
carrier:
collisions:
queue len:
1172590194
10921755
0
0
0
0
0
1000
r-qa-sit-switch01 (config) #
Step 6.
You are advised to check the software version embedded in your system, using the command
‘show version’. you can continue and compare this version to the latest version that can be
retrieved from Mellanox support site. To upgrade software, simply refer to MLNX-OS user
manual.
2.7.1.3 Remote Connection with MLNX-OS
Once the network attributes are set, you can access the CLI via SSH or the WebUI via HTTP/
HTTPs.
 To access the CLI, perform the following steps:
Step 1.
Set up an Ethernet connection between the system and a local network machine using a standard RJ45 connector.
Step 2.
Start a remote secured shell (SSH) using the command: “ssh -l <username> <IP_address>”,
# ssh -l <username> <ip_address>
Mellanox Technologies
39
Rev 1.2
Installation
Mellanox MLNX-OS Switch Management
Password:
Step 3.
Login as admin (default username is admin, password admin).
Step 4.
Once you get the CLI prompt, you are ready to use the system.
For additional information about MLNX-OS, refer to MLNX-OS User Manual located on Mellanox support web.
2.7.2
Configuring Network Attributes Using Cumulus Linux
For Cumulus Linux initial configuration instructions, see Configuring Cumulus Linux on the
Cumulus Linux Quick Start Guide.
2.7.2.1 Remote Connection with Cumulus Linux
Cumulus Linux uses the openSSH package to provide SSH functionality. To securely access a
Cumulus Linux switch remotely, please follow the instructions on the SSH for Remote Access
page in the Cumulus Linux User Guide.
2.8
FRU Replacements
2.8.1
Power Supply
Mellanox systems that are equipped with two replaceable power supply units work in a redundant configuration. Either unit may be extracted without bringing down the system.
Make sure that the power supply unit that you are NOT replacing is showing all green,
for both the power supply unit and System Status LEDs.
Power supply units have directional air flows similar to the fan module. The fan module airflow must coincide with the airflow of all of the power supply units. If the power
supply unit airflow direction is different from the fan module airflow direction, the
system’s internal temperature will be affected.
For power supply unit air flow direction, refer to Section 2.2 on page 16.
 To extract a power supply unit:
40
Step 1.
Remove the power cord from the power supply unit.
Step 2.
Grasping the handle with your hand, push the latch release with your thumb while pulling the
handle outward. As the power supply unit unseats, the power supply unit status LEDs will turn
off.
Step 3.
Remove the power supply unit.
Mellanox Technologies
Installation
Rev 1.2
Figure 34: PS Unit Pulled Out
 To insert a power supply unit:
Step 1.
Make sure the mating connector of the new unit is free of any dirt and/or obstacles.
Do not attempt to insert a power supply unit with a power cord connected to it.
Step 2.
Insert the power supply unit by sliding it into the opening, until a slight resistance is felt.
Step 3.
Continue pressing the power supply unit until it seats completely. The latch will snap into
place, confirming the proper installation.
Step 4.
Insert the power cord into the supply connector.
Step 5.
Insert the other end of the power cord into an outlet of the correct voltage.
The green power supply unit indicator should light. If it does not, repeat the whole procedure to extract the power supply unit and re-insert it.
2.8.2
Fans
The system can fully operate if one fan FRU is dysfunctional or missing. Failure of more than
one fan is not supported.
Make sure that the fans have the air flow that matches the model number. An air flow
opposite to the system design will cause the system to operate at a higher (less than
optimal) temperature.
For power supply unit air flow direction, refer to Section 2.2 on page 16.
Mellanox Technologies
41
Rev 1.2
Installation
 To remove a fan unit:
Step 1.
Grasping the handle with your right hand, push the latch release with your thumb while pulling
the handle outward. As the fan unit unseats, the fan unit status LEDs will turn off.
Step 2.
Remove the fan unit.
 To insert a fan unit:
Step 1.
Make sure the mating connector of the new unit is free of any dirt and/or obstacles.
Step 2.
Insert the fan unit by sliding it into the opening until slight resistance is felt. Continue pressing
the fan unit until it seats completely.
The green Fan Status LED should light. If not, extract the fan unit and reinsert it. After
two unsuccessful attempts to install the fan unit, power off the system before attempting any system debug.
Figure 35: Fan Module Latches
42
Mellanox Technologies
Software Management
3
Rev 1.2
Software Management
The systems include an embedded management CPU card that runs a management software.
•
For MLNX-OS systems management package and related documentation, visit the
product page:
http://www.mellanox.com/page/mlnx_os.
•
For Cumulus® Linux® software management instructions, refer to the Cumulus Linux
User Guide.
3.1
Upgrading Software
3.1.1
MLNX-OS Software Upgrade
Software and firmware updates are available from the Mellanox Support website. Check that
your current revision is the same one that is on the Mellanox website. If not upgrade your software. Copy the update to a known location on a Remote server within the user’s LAN.
Use the CLI or the GUI in order to perform software upgrades. For further information please
refer to the MLNX-OS Software User Manual section Upgrading MLNX-OS® Software.
Be sure to read and follow all of the instructions regarding the updating of the software on your
system.
The systems do not require Firmware updating. Firmware updating is done through the MLNXOS management software. The system comes standard with a management software module for
system management called Mellanox Operating System (MLNX-OS). MLNX-OS® includes a
CLI, WebUI, SNMP, system management software, Ethernet protocols and IB management software (OpenSM).
The Ethernet ports for remote management connect to Ethernet systems. These systems must be configured to 100Mb/1Gb auto-negotiation.
3.1.2
Cumulus Linux Software Upgrade
For Cumulus Linux software upgrade instructions, see Upgrading Cumulus Linux in the Cumulus Linux User Guide.
Mellanox Technologies
43
Rev 1.2
Interfaces
4
Interfaces
4.1
Supported Interfaces
The systems support the following interfaces:
•
Data interfaces - Ethernet
•
100/1000 MbE RJ45 management interface(s)
•
USB port
•
RS232 Console port
•
Reset button
•
Status and Port LEDs
In order to review the full configuration options matrix, refer to Table 4, “Management Interfaces
and FRUs”.
4.1.1
Data Interfaces
The data interfaces use QSFP28 connectors. The full list of interfaces per system is provided in
Table 3, “Speed and Switching Capabilities”.
Each QSFP28 port can be connected with a QSFP28 cable or connector for 25/40/50/56/100GbE,
or 1/10/25GbE when connecting through Mellanox QSFP28 to SFP28 (QSA) adapters, hybrid or
split cables.
The system offers High Power/LR4 transceivers support in all ports.
4.1.2
Speed
Ethernet speed must be set manually. The system’s ports can be manually configured to run at
speeds ranging from 1GbE to 100GbE (for more details, see “Specifications”). To change the
port speed configuration, use the command “speed” under interface configuration mode. Refer to
the MLNX-OS user manual for instructions on port speed re-configuration.
4.1.3
RS232 (Console)
The port labeled “Console”
is an RS232 serial port on the back side of the chassis that is
used for initial configuration and debugging. Upon first installation of the system, you need to
connect a PC to this interface and configure network parameters for remote connections. Refer to
Section 2.7.1 to view the full procedure.
4.1.4
Management
The two RJ45 Ethernet ports labeled “MGT”
provide access for remote management. The
management ports are configured with auto-negotiation capabilities by default (100MbE to
1000GbE). The management ports’ network attributes (such as IP address) need to be pre-config-
44
Mellanox Technologies
Interfaces
Rev 1.2
ured via the RS232 serial console port or by DHCP before use. Refer to Section 2.7.1 to view the
full procedure.
Make sure you use only FCC compliant Ethernet cables.
4.1.5
USB
The USB interface is USB 2.0 compliant and can be used by MLNX-OS software to connect to
an external disk for software upgrade or file management. The connector comes in a standard
USB shape.
To view the full matrix of the USB configuration options, refer to Table 4, “Management Interfaces and FRUs”.
USB 1.0 is not supported.
Do not use excessive force when inserting or extracting the USB disk from the connector.
4.1.6
Reset Button
The reset button is located on the rear side of the system next to the fan status LEDs. This reset
button requires a tool to be pressed.
Do not use a sharp pointed object such as a needle or a push pin for pressing the reset
button. Use a flat object to push the reset button.
To reset the system and the CPU of its management board, push the reset button and keep it
pressed for up to 15 seconds.
To reset the system, the CPU of its management board and the “admin” password, push the reset
button and keep it pressed for at least 15 seconds. You will then be able to enter without a password and set a new password for the user “admin”.
Mellanox Technologies
45
Rev 1.2
Interfaces
4.2
LEDs
4.2.1
LED Notifications
The system’s LEDs are an important tool for hardware event notification and troubleshooting.
Table 13 - LEDs Symbols
Symbol
Name
*
Description
Normal Conditions
System Status LED Shows the health of the system.
Green/Flashing
green when booting
Fan Status LED
Shows the health of the fans.
Green
Power supply units
LEDs
Shows the health of the power supply units.
Green
Bad Port LED
Lights up when a symbol error is detected on one Off
of the ports.
*Unit Identifier LED
Lights up on command through the CLI.
Off or blue when
identifying a port
*This function is currently disabled.
4.2.1.1 System Status LED
Figure 36: System Status LEDs - Front and Rear Sides
Both of these LEDs in
the red ovals show the
system’s status.
The right figure reflects
the system status LEDs
in SN2700. For
SN2410, see Figure 37.
In SN2410, the system status LEDs in the front panel are located above the LEDs of the SFP
ports.
46
Mellanox Technologies
Interfaces
Rev 1.2
Figure 37: System Status LEDs in SN2410 - Front Side
Both of the System Status LEDs (front and back) supply identical information.
It may take up to five minutes to turn on the system. If the System Status LED shows
red after five minutes, unplug the system and call your Mellanox representative for
assistance.
Table 14 - System Status LED Assignments
LED Behavior
Description
Action Required
Solid Green
The system is up and running normally.
N/A
Flashing Green
The system is booting up.
Wait up to five minutes for the end of the
booting process.
Solid Red
Major error has occurred. For exam- If the System Status LED shows red five
minutes after starting the system, unplug the
ple, corrupted firmware, system is
system and call your Mellanox representaoverheated etc.
tive for assistance.
4.2.1.2 Fan Status LED
Figure 38: Fan Status LED - Front and Rear Sides
Both of these LEDs in the red
ovals show the fans’ status.
Mellanox Technologies
47
Rev 1.2
Interfaces
Table 15 - Fan Status Front LED Assignments
LED
Behavior
Description
Action Required
Solid Green All fans are up and running.
N/A
Solid Red
Error, one or more fans are not operating properly.
The faulty FRUs should be replaced.
Off
System boot
N/A
Table 16 - Fan Status Rear LED Assignments (One LED per Fan)
LED
Behavior
Description
Action Required
Solid Green A specific fan unit is operating.
N/A
Solid Red
A specific fan unit is missing or not
operating properly.
The fan unit should be replaced.
Off
System boot
N/A
Risk of Electric Shock!
With the fan module removed, power pins are accessible within the module cavity.
Do not insert tools or body parts into the fan module cavity.
4.2.1.3 Power Supply Status LEDs
Figure 39: Power Status LED
There are two power supply inlets in the system (for redundancy). The system can operate with
only one power supply connected. In case the power supply is an FRU, a second power supply
unit can be added to support hot-swap ability. Each power supply unit has a single 2 color LED
on the right side of the unit, that indicates the status of the unit.
48
Mellanox Technologies
Interfaces
Rev 1.2
Figure 40: Rear Side Panel
The primary power supply (PS) unit is located on the left side and the secondary unit is located
on the right side.
Table 17 - Power Supply Unit Status Front LED Assignments
LED Behavior
Description
Action Required
Solid Green
All plugged (one or two) power supplies are
running normally.
N/A
Solid Red
One or both of the power supplies are not
Make sure the AC cable is plugged in
operational or not powered up/ the AC power and active. If the problem resumes, the
cable is disconnected.
FRUs might be faulty, and should then
be replaced.
Off
N/A
N/A
The power supply status LEDs on the rear side of the system are located on the PSUs themselves.
Each PSU has one LED of its own.
Table 18 - Power Supply Unit Status Rear LED Assignments
LED Behavior
Description
Action Required
Solid Green
The PSU is running normally.
N/A
Flashing Green 1Hz
AC present / Only 12VSB on (PSU off) or
PSU in Smart-on state.
Call your Mellanox representative for
assistance.
Amber
AC cord unplugged or AC power lost while
the second power supply still has AC input
power.
Plug in the AC cord of the faulty PSU.
PS failure (including voltage out of range and Check voltage. If OK, call your Mellapower cord disconnected).
nox representative for assistance.
Flashing Amber
Power supply warning events where the power Call your Mellanox representative for
supply continues to operate; high temp, high assistance.
power, high current, slow fan.
Off
No AC power to all power supplies.
Call your Mellanox representative for
assistance.
Mellanox Technologies
49
Rev 1.2
Interfaces
4.2.1.4 UID LED
The UID LED is a feature that can be used to find a particular system within a cluster. The specific system is signified by the blue UID LED.
4.2.1.5 Bad Port LED
The Bad Port LED indicator is used to indicate symbol errors in one or more system ports.
Table 19 shows the bad port status LED assignment.
Table 19 - Bad Port LED Assignments
LED Configuration
50
Description
Action Required
Off
No symbol errors have been received in last
few seconds (normal condition).
Flashing Amber
Error, one or more ports have received symbol Check symbol error counters on the syserrors.
tem UI to identify the ports.
Possible causes are:
Replace the cable on these ports.
• Bad cable
• Bad connection
• Bad connector
Mellanox Technologies
N/A
Interfaces
Rev 1.2
4.2.1.6 Port LEDs
Figure 41: SN2700 Port LEDs
Figure 42: SN2410 SFP28 Port LEDs
Figure 43: SN2410 QSFP28 Port LEDs
The status of each pair of adjacent QSFP28 ports is indicated by four LEDs, as shown in the picture above:
•
If the ports run at a 100GbE speed each, the two lower LEDs (2 and 4) will light green.
•
If the ports run at a 50GbE speed each, the left LEDs (1 and 2) will light green for the
upper port, and the right LEDs (3 and 4) will light green for the lower port.
•
If the ports run at a 25GbE speed each, all LEDs may light green, according to the
selected lane.
Table 20 - Port LEDs in Ethernet System Mode
LED Behavior
Description
Action Required
Off
Link is down.
Check the cable
Solid Green
Link is up with no traffic.
N/A
Flashing Green
Link is up with traffic.
N/A
Flashing Amber
A problem with the link.
Check the cable, and replace it if
needed.
Mellanox Technologies
51
Rev 1.2
4.3
Interfaces
Inventory Information
The system’s inventory parameters (such as serial number, part number, GUID and MAC
address) can be extracted from the inventory pull-out tab on the lower right side of the front
panel. In some systems, there is no pull-out tab, and the information is provided on labels in several locations.
Figure 44: SN2700 Pull-out Tab
52
Mellanox Technologies
Interfaces
Rev 1.2
Figure 45: SN2410 Inventory Information Illustration
Mellanox Technologies
53
Rev 1.2
Troubleshooting
5
Troubleshooting
5.1
Troubleshooting Instructions
Table 21 - Troubleshooting
Problem Indicator
LEDs
Symptoms
Corrective Measures
System Status LED is
blinking for more than
5 minutes
This state means that the MLNX-OS software did not
boot properly and only firmware is running.
To overcome it, connect to the system via the console
port, and check the software status. You might need to
contact an FAE if the MLNX-OS software did not load
properly
System Status LED is
red
This state can indicate a number of problems:
•
•
Critical system fault (CPU error, bad firmware)
Over Temperature
To overcome it:
•
Fan Status LED is red
This state is indicative of a problem with the FAN.
•
•
PSU Status LED is red
Mellanox Technologies
Check that the FAN is fully inserted and nothing blocks
the airflow.
Replace the FAN FRU if needed.
This state is indicative of a problem with the PSU.
•
•
54
Check Environmental conditions (room temperature)
Check/replace the power cable.
Replace the PSU if needed.
Troubleshooting
Rev 1.2
Table 21 - Troubleshooting
Problem Indicator
System boot failure
while using
MLNX-OS
Symptoms
The last software
upgrade failed on x86
based systems
Corrective Measures
•
•
•
Connect the RS232 connector (CONSOLE) to a laptop.
Push the system’s reset button.
Press the ArrowUp or ArrowDown key during the system
boot. GRUB menu will appear. For example:
Default image: 'SX_X86_64 SX_3.4.0008
2014-11-10 20:07:51 x86_64'
Press enter to boot this image, or
any other key for boot menu
Booting default image in 3 seconds.
Boot Menu
-----------------------------------------------------------------0: SX_X86_64 SX_3.4.0008 2014-11-10
20:07:51 x86_64
1: SX_X86_64 SX_3.4.0007 2014-10-23
17:27:34 x86_64
-----------------------------------------------------------------Use the ArrowUp and Arrowdown keys to
select which entry is highlighted.
Press enter to boot the selected
image or 'p' to enter a password to
unlock the next set of features.
Highlighted entry is 0:
"
•
System boot failure
while using Cumulus Linux
Select previous image to boot by pressing an arrow key
and choosing the appropriate image.
See Monitoring and Troubleshooting in Cumulus Linux
User Guide.
Mellanox Technologies
55
Rev 1.2
Specifications
6
Specifications
6.1
SN2700 Series
Table 22 - SN2700 Specifications
Feature
Mechanical
Value
Size:
Standard - 1.7” (H) x 16.85” (W) x27” (D),
43.6mm (H) x 428mm (W) x 685.8mm (D)
Mounting: 19” Rack mount
Mounting: 19” Rack mount
Weight:
1 PSU: 10.23kg
2 PSUs: 11.1kg
Speed: 10/25/40/50/56/100GbE per port
Connector cage: 32 QSFP28
Air flow:
Forward 65 CFM
Backward 57 CFM
Environmental
Temperature:
Operational: 0° to 45°C
Non-Operational: -40° to 70°C
Humidity:
Operational: 10% - 85% non-condensing
Non-Operational: 10% - 90% non-condensing
Altitude:
3050m
Regulatory
Safety: CS, cTUVus, CE, CU
EMC: CE, FCC, VCCI, ICES, RCM
RoHS6
Power
Input Voltage: 100-127VAC; 50/60Hz 3.5A; 200-240 50/60Hz 2.9A/ 192-288VDC (not cer-
tified)
Global Power Consumption:
40GbE Models -
Max power with optical cables (assuming 2W per port): 308.5W
100GbE Models -
Typical power with passive cables (ATIS): 150W
Max power with optical cables (assuming 3.5W per port): 398W
Main Devices
CPU: Intel Celeron 1047UE (x86)
Switch: Mellanox Spectrum™
Memory:
8GB DDR3 RAM
32GB SSD
56
Mellanox Technologies
Specifications
Rev 1.2
Table 22 - SN2700 Specifications
Feature
Switching
Value
Capacity: 6.4Tb/s
Mellanox Technologies
57
Rev 1.2
6.2
Specifications
SN2410 Series
Table 23 - SN2410 Specifications
Feature
Mechanical
Value
Size:
46.5mm (H) x 438mm (W) x 436mm (D)
Mounting: 19” Rack mount
Weight:
2 PSUs: 8.52kg
Speed: 10/25GbE per port (ports 1-48), 10/25/40/50/56/100GbE per port (ports 49-56)
Connector cage: 48xSFP28 and 8xQSFP28
Air flow:
Forward 60 CFM
Backward 45 CFM
Environmental
Temperature:
Operational: 0° to 45°C
Non-Operational: -40° to 70°C
Humidity:
Operational: 10% - 85% non-condensing
Non-Operational: 10% - 90% non-condensing
Altitude:
3050m
Regulatory
Safety: CS, cTUVus, CE, CU
EMC: CE, FCC, VCCI, ICES, RCM
RoHS6
Power
Input Voltage: 100-127Vac 50/60Hz 4.5A; 200-240 50/60Hz 2.9A/ 192-288VDC (not certified)
Global Power Consumption:
40GbE Models:
Max power with optical cables (assuming 2W per each QSFP port, and 1W per each SFP
port): 295.1
100GbE Models:
Typical power with passive cables (ATIS): 165W
Max power with optical cables (assuming 3.5W per each QSFP port, and 1.5W per each
SFP port): 362W
Main Devices
CPU: Intel Celeron 1047UE (x86)
Switch: Mellanox Spectrum™
Memory:
8GB DDR3 RAM
32GB SSD
Switching
58
Capacity: 4Tb/s
Mellanox Technologies
Rev 1.2
Appendix A: Accessory and Replacement Parts
Table 24 - OPNs for Replacement Parts
OPN
Part Description
MTEF-KIT-S
Rack installation kit for standard depth 1U systems to be mounted into standard depth racks
MTEF-KIT-BP
Rack installation kit for 1U wide systems to be mounted into short depth racks
MTEF-KIT-SP
Rack installation kit for 1U wide systems to be mounted into standard depth
racks
MTEF-PSF-AC-A
460W AC Power Supply w/ rear to front air flow
MTEF-PSR-AC-A
460W AC Power Supply w/ front to rear air flow
HAR000028
Harness RS232 2M cable – DB9 to RJ-45
ACC000501
Power cord Type C13-C14
MTEF-FANF-A
Fan module w/rear to front airflow
MTEF-FANR-A
Fan module w/front to rear airflow fan for SX67X0/SX1710 switch systems
Mellanox Technologies
59
Rev 1.2
Appendix B: Thermal Threshold Definitions
There are three thermal threshold definitions for the switch device which impact the overall
switch system operation state:
•
Warning – 105°C: On managed systems only: When the device crosses the 100°C
threshold, a Warning Threshold message will be issued by the management SW, indicating to system administration that the switch has crossed the Warning threshold. Note
that this temperature threshold does not require nor lead to any action by hardware
(such as switch shutdown).
•
Critical – 120°C: When the device crosses this temperature, the firmware will automatically shut down the device.
•
Emergency – 130°C: In case the firmware fails to shut down the device upon crossing
the Critical threshold, the device will auto-shutdown upon crossing the Emergency
(130°C) threshold.
For thermal threshold definitions in Cumulus Linux, see Configuring Net-SNMP
Event Notification Traps in the Cumulus Networks Help Center.
60
Mellanox Technologies
Rev 1.2
Appendix C: Interface Specifications
C.1
QSFP Interface
21
22
23
24
25
26
27
28
29
30
31
32
GND
GND
Ground
2
Tx2n
Transmitter Inverted Data Input
Tx2p
Transmitter Non-Inverted Data Input
4
GND
Ground
5
Tx4n
Transmitter Inverted Data Input
19
6
Tx4p
Transmitter Non-Inverted Data Input
Ground
Rx1n
7
GND
Rx2p
Rx1p
17
8
ModSelL
Module Select
GND
GND
16
9
ResetL
Module Reset
Rx4n
Rx3n
10
Vcc Rx
+3.3 V Power supply receiver
Rx4p
Rx3p
GND
GND
ModPrsL
SDA
IntL
SCL
VccTx
Vcc1
LPMode
GND
Vcc Rx
ResetL
ModSelL
GND
Tx3p
Tx4p
Tx3n
35
GND
Tx4n
GND
38
GND
Rx2n
34
37
1
Signal Description
18
33
36
Connector
Pin Name
3
J3 and J6
20
Connector
Pin Number
Tx1p
Tx1n
GND
15
14
13
11
SCL
2-wire serial interface clock
12
12
SDA
2-wire serial interface data
11
13
GND
Ground
10
14
Rx3p
Receiver Non-Inverted Data Output
9
15
Rx3n
Receiver Inverted Data Output
8
16
GND
Ground
7
17
Rx1p
Receiver Non-Inverted Data Output
6
18
Rx1n
Receiver Inverted Data Output
5
4
19
GND
Ground
Tx2p
3
20
GND
Ground
Tx2n
2
1
21
Rx2n
Receiver Inverted Data Output 3
22
Rx2p
Receiver Non-Inverted Data Output 3
23
GND
Ground
24
Rx4n
Receiver Inverted Data Output 3
25
Rx4p
Receiver Non-Inverted Data Output 3
26
GND
Ground
27
ModPrsL
28
IntL
29
Vcc Tx
+3.3 V Power supply transmitter
30
Vcc 1
+3.3 V Power Supply
31
LPMode
32
GND
Ground
33
Tx3p
Transmitter Non-Inverted Data Input
34
Tx3n
Transmitter Inverted Data Input
35
GND
Ground
36
Tx1p
Transmitter Non-Inverted Data Input
37
Tx1n
Transmitter Inverted Data Input
GND
Module Present
Interrupt
Low Power Mode
Mellanox Technologies
61
8
10
9
11
12
13
14
15
16
17
18
19
ModSelL
ResetL
SCL
SDA
GND
RX3p
RX3n
GND
RX1p
RX1n
GND
VccRx
7
GND
20 GND
21 RX2n
22 RX2p
23 GND
24 RX4n
25 RX4p
26 GND
27 ModPrsL
28 IntL
29 VccTx
30 Vcc1
31 LPMode
32 GND
14
13
12
11
10
9
8
7
6
5
4
3
2
1
15
TX2n
33 TX3p
TX2p
6
TX4p
16
GND
34 TX3n
TX4n
5
TX4n
TX4p
18
17
GND
35 GND
ModSelL
4
GND
ResetL
36 TX1p
VccRx
3
TX2p
SCL
2
TX2n
SDA
GND
GND
19
GND 3 8
TX1n 3 7
TX1p 3 6
GND 3 5
TX3n 3 4
TX3p 3 3
GND 3 2
RX3p
Top 18.35
LPMode 3 1
RX3n
37 TX1n
Top
Vcc1 30
GND
RX1p
RX1n
38 GND
18.35
View into Rear of
Connector
VccTx 29
IntL 28
ModPrsL 27
GND 26
RX4p 25
RX4n 24
GND 23
RX2p 22
RX2n 21
GND 20
1
Mellanox Technologies
62
GND
GND
Rev 1.2
Figure 46: QSFP Connector Male and Female Views
8.50
View into Front of Cage
8.50
Rev 1.2
C.2
SFP+ Interface
56.50
13.90
14.80
Mellanox Technologies
MTSFPP-SR Module
13.60
11.85
13.70
1.55
0.50
8.50
1.80
2.55
0.60
44.95
Figure 47: Rear View of Module With Pin Placement
Top
13.70
8.50
VeeR
RD-
RD+
VeeR
VccR
VccT
11
12
13
15
16
14
VeeT 17
19
18
TD-
20
TD+
VeeT
7
MOD_ABS
RS0
VeeR
6
SCL
10
5
SDA
RS1
4
TX_Disable
9
3
TX_Fault
RX_LOS
2
VeeT
8
1
Mellanox Technologies
63
Rev 1.2
Pin
Symbol Name
Description
1
VeeT
Transmitter Ground (Common with Receiver Ground) a
2
TX_Fault
Transmitter Fault.b
3
TX_Disable
Transmitter Disable. Laser output disabled on high or open. c
4
SDA
2-wire Serial Interface Data Line d
5
SCL
2-wire Serial Interface Clock Line d
6
MOD_ABS
Module Absent. Grounded within the module d
7
RS0
No connection required
8
RX_LOS
Loss of Signal indication. Logic 0 indicates normal operation. e
9
RS1
No connection required
10
VeeR
Receiver Ground (Common with Transmitter Ground) a
11
VeeR
Receiver Ground (Common with Transmitter Ground)a
12
RD-
Receiver Inverted DATA out. AC Coupled
13
RD+
Receiver Non-inverted DATA out. AC Coupled
14
VeeR
Receiver Ground (Common with Transmitter Ground) a
15
VccR
Receiver Power Supply
16
VccT
Transmitter Power Supply
17
VeeT
Transmitter Ground (Common with Receiver Ground) a
18
TD+
Transmitter Non-Inverted DATA in. AC Coupled.
19
TD-
Transmitter Inverted DATA in. AC Coupled.
20
VeeT
Transmitter Ground (Common with Receiver Ground)a
a. Circuit ground is internally isolated from chassis ground.
b. TFAULT is an open collector/drain output, which should be pulled up with a 4.7k – 10k Ohms
resistor on the host board if intended for use. Pull up voltage should be between 2.0V to Vcc +
0.3V. A high output indicates a transmitter fault caused by either the TX bias current or the TX
output power exceeding the preset alarm thresholds. A low output indicates normal operation.
In the low state, the output is pulled to <0.8V.
c. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V
d. Should be pulled up with 4.7kΩ – 10kΩ on host board to a voltage between 2.0V and 3.6V.
MOD_ABS pulls line low to indicate module is plugged in.
e. LOS is open collector output. Should be pulled up with 4.7kΩ – 10kΩ on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
64
Mellanox Technologies
Rev 1.2
C.3
RJ45 to DB9 Harness Pinout
In order to connect a host PC to the Console RJ45 port of the system, a RS232 harness cable
(DB9 to RJ45) is supplied.
Figure 48: RJ45 to DB9 Harness Pinout
Mellanox Technologies
65
Rev 1.2
Appendix D: Disassembly and Disposal
D.1
Disassembly Procedure
 To disassemble the system from the rack:
1. Unplug and remove all connectors.
2. Unplug all power cords.
3. Remove the ground wire.
4. Unscrew the center bolts from the side of the system with the bracket.
Support the weight of the system when you remove the screws so that the system does
not fall.
5. Slide the system from the rack.
6. Remove the rail slides from the rack.
7. Remove the caged nuts.
D.2
Disposal
According to the WEEE Directive 2002/96/EC, all waste electrical and electronic
equipment (EEE) should be collected separately and not disposed of with regular
household waste.
Dispose of this product and all of its parts in a responsible and environmentally
friendly way.
Follow the instructions found at http://www.mellanox.com/page/dismantling_procedures for
proper disassembly and disposal of the switch, according to the WEEE directive.
66
Mellanox Technologies
Rev 1.2
Appendix E: Safety Warnings (Multiple Languages)
E.1
Nordic Countries Notices
In Finland: "Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan"
In Norway: "Apparatet må tilkoples jordet stikkontakt"
In Sweden: "Apparaten skall anslutas till jordat uttag"
E.2
Installation Safety Warnings (English)
1. Installation Instructions
Read all installation instructions before connecting the equipment to the power source.
2. Bodily Injury Due to Weight
Use enough people to safely lift this product.
<40 lbs
<18 kgs
40 - 70 lbs
18 - 32 kgs
70 - 121 lbs
32 - 55 kgs
>121 lbs
>55 kgs
3. Heavy Equipment
This equipment is heavy and should be moved using a mechanical lift to avoid injuries.
4. Risk of Electric Shock!
Risk of Electric Shock!
With the fan module removed power pins are accessible within the module cavity.
Do not insert tools or body parts into the fan module cavity.
5. Over-temperature
This equipment should not be operated in an area with an ambient temperature exceeding the maximum recommended: 45°C (113°F). Moreover, to guarantee proper , allow
at least 8cm (3 inches) of clearance around the ventilation openings.
Mellanox Technologies
67
6. Stacking the Chassis
The chassis should not be stacked on any other equipment. If the chassis falls, it can
cause bodily injury and equipment damage.
7. Redundant Power Supply Connection - Electrical Hazard
This product includes a redundant power or a blank in its place. In case of a blank
power supply, do not operate the product with the blank cover removed or not securely
fastened.
8. Double Pole/Neutral Fusing
This system has double pole/neutral fusing. Remove all power cords before opening
the cover of this product or touching any internal parts.
9. Multiple Power Inlets
Risk of electric shock and energy hazard.
The PSUs are all independent.
Disconnect all power supplies to ensure a powered down state inside of the switch
platform.
10. During Lightning - Electrical Hazard
During periods of lightning activity, do not work on the equipment or connect or disconnect cables.
11. CopperCable Connecting/Disconnecting
Copper cables are heavy and not flexible, as such they should be carefully attached to
or detached from the connectors. Refer to the cable manufacturer for special warnings/
instructions.
12. Rack Mounting and Servicing
When this product is mounted or serviced in a rack, special precautions must be taken
to ensure that the system remains stable. In general you should fill the rack with equipment starting from the bottom to the top.
68
Mellanox Technologies
Rev 1.2
13. Equipment Installation
This equipment should be installed, replaced, and/or serviced only by trained and qualified personnel.
14. Equipment Disposal
Disposal of this equipment should be in accordance to all national laws and regulations.
15. Local and National Electrical Codes
This equipment should be installed in compliance with local and national electrical
codes.
16. Installation Codes
This device must be installed according to the latest version of the country
national electrical codes. For North America, equipment must be installed in
accordance to the applicable requirements in the US National Electrical Code
and the Canadian Electrical Code.
17. Battery Replacement
Warning: Replace only with UL Recognized battery, certified for maximum
abnormal charging current not less than 4mA
There is a risk of explosion should the battery be replaced with a battery of an
incorrect type.
Dispose of used batteries according to the instructions.
18. UL Listed and CSA Certified Power Supply Cord
For North American power connection, select a power supply cord that is UL Listed
and CSA Certified, 3 - conductor, [16 AWG], terminated with a molded plug rated at
125 V, [13 A], with a minimum length of 1.5m [six feet] but no longer than 4.5m.
For European connection, select a power supply cord that is internationally
harmonized and marked “<HAR>”, 3 - conductor, minimum 1.0 mm2 wire,
rated at 300 V, with a PVC insulated jacket. The cord must have a molded plug
rated at 250 V, 10 A.
19. Installation codes
This device must be installed according to the latest version of the country national
electrical codes. For North America, equipment must be installed in accordance to the
applicable requirements in the US National Electrical Code and the Canadian Electrical Code.
Mellanox Technologies
69
20. Interconnection Of Units
Cables for connecting to the unit RS232 and Ethernet Interfaces must be UL
certified type DP-1 or DP-2. (Note- when residing in non LPS circuit)
21. Overcurrent Protection
A readily accessible Listed branch circuit overcurrent protective device rated
20 A must be incorporated in the building wiring.
22. Do Not Use the Switch as a Shelf or Work Space
Caution: Slide/rail mounted equipment is not to be used as a shelf or a work space. The
rails are not intended for sliding the unit away from the rack. It is for permanent installation at final resting place only, not used for service and maintenance
23. WEEE Directive
According to the WEEE Directive 2002/96/EC, all waste electrical and electronic
equipment (EEE) should be collected separately and not disposed of with regular
household waste.
Dispose of this product and all of its parts in a responsible and environmentally
friendly way.
24. Country of Norway Power Restrictions
This unit is intended for connection to a TN power system and an IT power system of
Norway only.
E.3
‫( אזהרות בטיחות בהתקנה‬Hebrew)
1. ‫הוראות התקנה‬
70
Mellanox Technologies
‫‪Rev 1.2‬‬
‫‪>121 lbs‬‬
‫‪>55 kgs‬‬
‫‪70 - 121 lbs‬‬
‫‪32 - 55 kgs‬‬
‫תקן ישראלי‬
‫‪2.‬‬
‫חבלת גוף כתוצאה מנשיאת משקל יתר‬
‫‪3.‬‬
‫‪40 - 70 lbs‬‬
‫‪18 - 32 kgs‬‬
‫‪<40 lbs‬‬
‫‪<18 kgs‬‬
‫ציוד כבד‬
‫‪4.‬‬
‫סכנת התחשמלות!‬
‫‪5.‬‬
‫התחממות יתר ‪6.‬‬
‫ערימת המערכת‬
‫‪71‬‬
‫‪Mellanox Technologies‬‬
‫‪7.‬‬
‫חיבור ספק כוח נוסף ‪-‬סכנת חשמל‬
‫‪8.‬‬
‫‪.‬‬
‫מספר שקעים חשמליים‬
‫‪9.‬‬
‫בעת סופות ברקים ‪ -‬סכנת חשמל ‪10.‬‬
‫חיבור או ניתוק של כבלי נחושת ‪11.‬‬
‫הרכבה על גבי מדף בארון ‪12.‬‬
‫התקנת המוצר ‪13.‬‬
‫‪Mellanox Technologies‬‬
‫‪72‬‬
‫‪Rev 1.2‬‬
‫השלכת פסולת ‪14.‬‬
‫תקנות חשמל מקומיות ולאומיות ‪15.‬‬
‫כבל אספקת חשמל ‪16.‬‬
‫תקנות התקנה ‪17.‬‬
‫חיבור בין מערכות‬
‫‪18.‬‬
‫הגנה מפני מתח גבוה ‪19.‬‬
‫‪73‬‬
‫‪Mellanox Technologies‬‬
20. ‫אין להשתמש במערכת כמדף או שטח עבודה‬
21. WEEE ‫תקנת‬
22. ‫מגבלות חשמליות בנורבגיה‬
E.4
安裝安全性警告 (Chinese)
1. 安裝指示
本設備附有備援電源供應器或在適當位置配有空白蓋板。
2. 因重量導致的人身受傷
為了安全起見,請安排足夠的人員以合力抬起本產品。
<40 lbs
<18 kgs
74
Mellanox Technologies
40 - 70 lbs
18 - 32 kgs
70 - 121 lbs
32 - 55 kgs
>121 lbs
>55 kgs
Rev 1.2
3. 重設備
本設備極重,應使用機械式起重機來搬移,以避免人員受傷。
4. 有觸電的危險
有觸電的危險!
拆除風扇模組後,即可接觸到模組空腔內的電源針腳。
請勿將工具或機身零件插入到風扇模組空腔內。
5. 溫度過高
本設備不應在超過所建議的最高環境溫度的區域中運作:45°C (113°F)。此外,
為了保證氣流的流通正常,請在通風口旁保留至少 8 公分 (3 英吋 ) 的間距。
6. 堆疊機箱
機箱不應堆疊在任何其他設備上。如果機箱掉落,可能造成人員受傷與設備損
壞。
7. 複式電源連接時的電擊危險
本設備附有備援電源供應器或在適當位置配有空白蓋板。如果是電源供應器空
白蓋板,在空白蓋板已取下或未牢牢固訂的情況下,請勿操作本產品。
8. 雙極 / 中性保險絲
本系統具有雙極 / 中性保險絲。請拔掉所有電源線後,再打開本產品的蓋板或
碰觸任何內部零件。
9. 多電源輸入座
電擊與能源危害的危險。
所有 PSU 均各自獨立。
將所有電源供應器斷電,確保交換器平台內部在電源關閉狀態。
Mellanox Technologies
75
10. 閃電時的電擊危險
在閃電期間,不要使用本設備或連接或拔下纜線。
11.
機架安裝與維修
此產品已安裝在機架中或在機架中維修時,必須採取特定預防措施以確保系統
維持穩定。一般您應該將設備從底部到頂端放滿機架。
12. 設備安裝
本設備僅限由經過訓練與 / 或合格的人員安裝、更換或維修。
13. 設備棄置
棄置本設備應遵照所有國內法規。
14. 當地與國家電氣法規
請遵照當地與國家電氣法規安裝本設備。
15. 安裝法規
請務必遵循最新版的國家電氣法規,安裝本設備。在北美地區,請務必遵循美
國國家電工法規和加拿大電工法規中的適用規定,安裝本設備。
16. 更換電池
警告:只能以 UL 認可電池,且取得最大異常充電電流低於 4mA 認證的電池進
行更換。
若更換錯誤類型的電池,會有爆炸的危險。
請依據指示棄置廢電池。
76
Mellanox Technologies
Rev 1.2
17. UL 列名和 CSA 認證電源線
北美地區在接上電源時,請選用獲得 UL 列名和 CSA 認證、三個導體、[16
AWG] 附成型插頭,額定值為 125 V、[13 A],長度至少 1.5 公尺 [ 六英尺 ],但
不超過 4.5 公尺的電源線。
歐洲地區在接上電源時,請選用國際協調式且標示有 <HAR> 字樣、三個導體、
標稱截面至少 1.0 平方公厘,額定值為 300 V,採用 PVC 絕緣的電源線。電源
線需有成型插頭,額定值為 250 V, 10 A。
18. 高漏電流
警告: 高漏電流;必須執行地線連接,然後再連接電源供應器。
19. 安裝法規
請務必遵循最新版的國家電氣法規,安裝本設備。在北美地區,請務必遵循美
國國家電工法規和加拿大電工法規中的適用規定,安裝本設備。
20. 互連設備
連接至 RS232 設備和乙太網路介面的纜線必須是 UL 認證類型 DP-1 或 DP-2。
( 請注意位於非 LPS 電路時 )
過電流保護:準備好使用的列名分支電路過電流保護裝置最大額定值 20 A 必須
整合在配線中。
21. 切換開關不可用作機架或工作空間
小心:滑軌 / 導軌安裝設備不可用作機架或工作空間。導軌不適用於將設備滑
出機架使用。僅限永久安裝在最後安置區域時使用,不可用於維修和保養。
22. WEEE 指令
根據 WEEE 指令 2002/96/EC,所有廢棄的電氣與電子設備 (EEE),應分開集
中,而且不應與一般家庭廢棄物一起棄置。
請以負責和環保的方式棄置本產品及其所有零件。
Mellanox Technologies
77
23. 挪威國家電源限制
本設備僅限連接至挪威的 TN 電源系統和 IT 電源系統。
24. China CCC Warning Statement
78
Mellanox Technologies
Rev 1.2
25. Taiwan BSMI Class A Statement - Warning to the User!
E.5
Avertissements de sécurité pour l'installation (French)
1. Instructions d'installation
Veuillez lire la totalité des instructions d'installation avant de relier l'équipement au
secteur.
2. Blessures à cause du poids
Prévoyez assez de personnel pour soulever ce produit en toute sécurité.
<40 lbs
<18 kgs
3.
40 - 70 lbs
18 - 32 kgs
70 - 121 lbs
32 - 55 kgs
>121 lbs
>55 kgs
Équipement lourd
Cet équipement est lourd et doit être déplacé avec un système de levage mécanique
pour éviter les blessures.
4. Danger d'électrocution
Danger d'électrocution !
Lorsque le module de ventilation est retiré, les broches d'alimentation sont exposées
dans l'emplacement du module.
NE PAS insérer d'outils ou la main dans l'emplacement du module.
5.
Surchauffe
Cet équipement ne doit pas être en service dans un local dont la température dépasse le
maximum recommandé de 45°C (113°F). En outre et pour garantir une circulation
d'air correcte, laisser un espace d'au moins 8 cm (3") autour des orifices de ventilation.
Mellanox Technologies
79
6. Châssis empilé sur d'autres équipements
Le châssis ne doit pas être empilé sur d'autres équipements. S'il tombe, il peut endommager l'équipement ou entraîner des blessures.
7. Connexion de l'alimentation redondante : danger d'électrocution
Ce produit est équipé d'une alimentation redondante ou d'un cache si elle est absente.
Dans ce dernier cas, ne pas faire fonctionner le produit si le cache est retiré ou mal
fixé.
8. Fusibles phase/neutre
Ce système dispose de fusibles phase/neutre. Débranchez tous les cordons d'alimentation avant d'ouvrir le capot ou de toucher tout élément à l'intérieur.
9. Plusieurs prises d'alimentation
Risque et danger d'électrocution.
Les alimentations sont toutes indépendantes.
Pour s'assurer que le commutateur est bien hors tension, débranchez toutes les alimentations.
10. En cas d'orage, danger d'électrocution
Pendant un orage, ne pas travailler sur l'équipement ni brancher ou débrancher des
câbles.
11. Connexion et déconnexion du câble en cuivre
Les câbles en cuivre sont lourds et peu flexibles. Par conséquent, il faut procéder avec
soin pour les brancher ou les débrancher des connecteurs. Consulter le fabricant du
câble pour obtenir des instructions ou des avertissements spécifiques.
12. Montage en rack et maintenance
Lors du montage ou de la maintenance de ce produit dans un rack, il faut faire spécialement attention pour s'assurer que l'ensemble reste stable. En règle générale, le rack doit
être rempli en commençant par le bas.
80
Mellanox Technologies
Rev 1.2
13. Installation de l'équipement
Cet équipement ne doit être installé, remplacé et maintenu que par un personnel formé
et qualifié.
14. Mise au rebut de l'équipement
La mise au rebut de cet équipement doit se faire conformément à toutes les lois et
réglementations nationales.
15. Codes électriques locaux et nationaux
Cet équipement doit être installé conformément aux codes électriques locaux et nationaux.
16. Codes d'installation
Cet appareil doit être installé conformément à la version la plus récente des codes électrique nationaux. En Amérique du Nord, l'équipement doit être installé en respectant
les exigences de l'US National Electrical Code et du Code canadien de l'électricité.
17. Remplacement de la batterie
Avertissement : ne remplacer qu'avec une batterie UL, certifiée pour accepter un courant de charge anormal maximal supérieur ou égal à 4 mA.
Si la batterie n'est pas remplacée par un type correct, il y a un risque d'explosion.
Les batteries usagées doivent être mises au rebut conformément aux instructions.
18. Cordon d'alimentation UL Listed et certifié CSA
Pour le branchement électrique en Amérique du Nord, utiliser un cordon d'alimentation UL Listed et CSA Certified, à 3 conducteurs [calibre 16 AWG], avec une prise
moulée 125 V [13 A], faisant au moins 1,5 m de long [six pieds] et au plus 4,5 m.
Pour le branchement électrique en Europe, utiliser un cordon d'alimentation au format
international harmonisé (marqué <HAR>), à 3 conducteurs d'au moins 1 mm2 de section, 300 V, avec une gaine isolante en PVC. Le cordon doit avoir une prise moulée
250 V 10 A.
19. Courant de fuite élevé
Avertissement : courant de fuite élevé, une connexion à la terre est indispensable
avant de brancher l'alimentation.
Mellanox Technologies
81
20. Codes d'installation
Cet appareil doit être installé conformément à la version la plus récente des codes électrique nationaux. En Amérique du Nord, l'équipement doit être installé en respectant
les exigences de l'US National Electrical Code et du Code canadien de l'électricité.
21. Interconnexion des unités
Les câbles de connexion aux interfaces RS232 et Ethernet de l'appareil doivent être
certifié UL de type DP-1 ou DP-2. (Note : en cas d'installation sur un circuit dont la
puissance n'est pas limitée)
Protection contre les surintensités : le câblage de l'immeuble doit intégrer un dispositif
certifié de protection contre les surintensités, calibré à 20 A et aisément accessible.
22. Ne pas utiliser comme étagère ou plan de travail
Attention : un équipement coulissant ou monté sur rail ne doit pas servir d'étagère ni de
plan de travail. Les rails ne sont pas destinés à faire coulisser l'unité hors du rack. Ils
sont destinés à une installation permanente à l'emplacement final, pas pour l'entretien
ni la maintenance.
23. Directive DEEE
Selon la Directive 2002/96/CE (DEEE), tous les déchets d'équipements électriques et
électroniques (EEE) doivent être collectés séparément et ne pas être mis au rebut avec
les déchets ménagers habituels.
Ce produit et toutes ses pièces doivent être mis au rebut d'une manière responsable,
respectant l'environnement.
24. Restrictions concernant l'alimentation pour la Norvège
Cet appareil est prévu pour être relié à un système d'alimentation TN et un système
d'alimentation informatique de Norvège uniquement.
E.6
Installation Sicherheitshinweise(German)
1. Installationsanleitungen
Lesen Sie alle Installationsanleitungen, bevor Sie das Gerät an die Stromversorgung
anschließen.
82
Mellanox Technologies
Rev 1.2
2. Verletzungsgefahr wegen des Gewichts
Um das Produkt sicher anzuheben, genügend Personen einsetzen.
<40 lbs
<18 kgs
40 - 70 lbs
18 - 32 kgs
70 - 121 lbs
32 - 55 kgs
>121 lbs
>55 kgs
3. Schweres Gerät
Dieses Gerät ist schwer und muss mit einem mechanischen Hebegerät verschoben
werden, um Verletzungen zu vermeiden.
4. Stromschlagrisiko
Stromschlagrisiko!
Bei abgenommenem Ventilatormodul sind die Stromkontakte in der Modulvertiefung
zugänglich.
Es dürfen KEINE Werkzeuge oder Körperteile in die Vertiefung des Ventilatormoduls
gelangen.
5. Übertemperatur
Dieses Gerät sollte nicht in einem Bereich mit einer Umgebungstemperatur über der
maximal empfohlenen Temperatur von 45°C (113°F) betrieben werden. Es ist ein Luftstrom von 200 LFM bei maximaler Umgebungstemperatur erforderlich. Außerdem
sollten mindestens 8 cm (3 in.) Freiraum um die Belüftungsöffnungen sein, um einen
einwandfreien Luftstrom zu gewährleisten.
6. Stapeln des Chassis
Das Chassis sollte nicht auf andere Geräte gestapelt werden. Wenn das Chassis herunterfällt, kann es zu Verletzungen und Beschädigungen an Geräten führen.
7. Zweipolig/Neutrale Sicherung
Achtung:
Zweipolige bzw. Neutralleiter-Sicherung im Netzteil. Netzstecker ziehen, um sicherzustellen, daß keine Spannung am Gerät anliegt. Entfernen Sie alle Netzkabel vor dem
Öffnen der Abdeckung dieses Produkts oder dem Berühren der Innenteile.
Mellanox Technologies
83
8. Mehrere Stromeingänge
Risiko eines Stromschlags und Stomgefahr.
Alle Stromversorgungseinheiten sind unabhängig.
Trennen Sie alle Stomversorgungen, um einen abgeschalteten Zustand im Inneren der
Switch-Plattform sicherzustellen.
9. Bei Gewitter - Elektrische Gefahr
Arbeiten Sie während eines Gewitters und Blitzschlag nicht am Gerät, schließen Sie
keine Kabel an oder ab.
10. Anschließen/Trennen von Kupferkabel
Kupferkabel sind schwer und nicht flexible. Deshalb müssen sie vorsichtig an die
Anschlüsse angebracht bzw. davon getrennt werden. Lesen Sie die speziellen Warnungen und Anleitungen des Kabelherstellers.
11. Rack-Montage und Wartung
Wenn dieses Produkt in einem Rack montiert oder gewartet wird, sind besondere Vorsichtsmaßnahmen zu ergreifen, um die Stabilität des Systems zu gewährleisten. Im
Allgemeinen sollten Sie das Gestell von unten nach oben mit Geräten füllen.
12. Geräteinstallation
Diese Gerät sollte nur von geschultem und qualifiziertem Personal installiert, ausgetauscht oder gewartet werden.
13. Geräteentsorgung
Die Entsorgung dieses Geräts sollte unter Beachtung aller nationalen Gesetze Bestimmungen erfolgen.
14. Regionale und nationale elektrische Bestimmungen
Dieses Gerät sollte unter Beachtung der regionalen und nationalen elektrischen Bestimmungen installiert werden.
84
Mellanox Technologies
Rev 1.2
15. Installationscodes
Dieses Gerät muss entsprechend der aktuellsten Version des National Electrical Code
installiert weden. In Nodamerika muss das Gerät gemäß den geltenden Anforderungen
des US National Electrical Code und des Canadian Electrical Code installiert werden.
16. Akkuaustausch
Warnung: Nur durch von UL anerkannten Akkus ersetzen, die für maximalen anormalen Ladestrom von nicht weniger als 4mA zertifiziert sind.
Es besteht Explosiionsgefahr, wenn der Akku durch einen Akku eines falschen Typs
ersetzt wird.
Akkus gemäß den Anweisungen entsorgen.
17. UL- und CSA-zertifiziertes Netzkabel
Für Nordamerika Stromanschluss, wählen Sie ein Netzkabel, das UL-und CSA Certified
3 - Leiter, [18 AWG], mit einem angespritztem Stecker bewertet bei 125 V, [15], mit
einer Mindestlänge von 1,5 m [Six Feet] aber nicht mehr als 4,5 m.
Für die europäischen Zusammenhang, wählen Sie ein Netzkabel, das international
harmonisiert und der Aufschrift "<HAR>",
3 - Leiter, mindestens 0,75 mm2 Draht, bewertet mit 300 V, mit einem PVC-Mantel
isoliert. Das Kabel muss eine angespritztem Stecker bewertet bei 250 V, 10 A. "
18. Hoher Ableitstrom
WARNUNG: Hohe Ableitstrom; Earth Verbindung, bevor Sie die Verbindung von
wesentlicher Bedeutung werden.
19. Installationscodes
Dieses Gerät muss installiert sein, entsprechend auf die neueste Version des Landes
National Electrical Code. Für Nordamerika, müssen in Übereinstimmung mit den geltenden Vorschriften in der US-amerikanischen National Electrical Code und dem
Canadian Electrical Code.
20. Verbindung der Geräte untereinander
Kabel für den Anschluss an das Gerät RS232-und Ethernet-Schnittstellen müssen UL
zertifiziert Typ DP-1 oder DP-2. (Hinweis-, wenn nicht mit Wohnsitz in LPS-Schaltung)
Überstromschutz: Eine leicht zugängliche Auflistung Abzweigleitung ÜberstromSchutzeinrichtung 20 A bewertet werden müssen in dem Gebäude Verkabelung.
Mellanox Technologies
85
21. Switch nicht als Regal oder Arbeitsplatz nutzen
Achtung: Auf Schieber/Schienen montiertes Gerät ist nicht als Regal oder Arbeitsbereich zu nutzen. Die Schienen sind nicht dafür bestimmt, die Einheit aus dem Gestell
weg zu ziehen. Sie sind nur für die permanente Installation an einem endgültigen Standort gedacht, nicht für Instandhaltung und Wartung.
22. WEEE-Direktive
Gemäß WEEE Directive 2002/96/EC müssen alle elektrischen und elektronischen
Abfallgeräte (EEE) separat gesammelt und nichit mit normalem Haushaltsmüll ensorgt
werden.
Dieses Produkt und alle seine Teile in verantwortungsvoller und umweltfreundlicher
Art und Weise entsorgen.
E.7
Advertencias de seguridad de instalación (Spanish)
1. Instrucciones de instalación
Antes de conectar el equipo a la fuente de alimentación, leer todas las instrucciones de
instalación.
2. Lesión corporal a causa de peso
Recurra a suficientes personas para levantar este producto sin
<40 lbs
<18 kgs
40 - 70 lbs
18 - 32 kgs
70 - 121 lbs
32 - 55 kgs
>121 lbs
>55 kgs
3. Equipos pesados
Dado que el equipo es pesado, se debe mover únicamente mediante un elevador
mecánico, para evitar lesiones.
86
Mellanox Technologies
Rev 1.2
4. Riesgo de descarga eléctrica
¡Riesgo de descarga eléctrica!
Con el módulo del ventilador quitado, se obtiene acceso a las clavijas de alimentación
desde dentro de la cavidad del módulo.
NO introducir herramientas ni partes del cuerpo en la cavidad del módulo del ventilador.
5. Sobretemperatura
No se debe utilizar el equipo en un área con una temperatura ambiente superior a la
máxima recomendada: 45°C. Además, para garantizar una circulación de aire adecuada, se debe dejar como mínimo un espacio de 8 cm (3 pulgadas) alrededor de las
aberturas de ventilación.
6. Apilamiento del chasis
Los chasis no se deben apilar sobre otros equipos. La caída del chasis podría causar
lesiones corporales, así como daños al equipo.
7. Conexión redundante de fuente de alimentación: peligro de descarga
Este producto incluye una fuente de alimentación redundante o, en su lugar, una vacía.
Si se dispone de una fuente de alimentación vacía, no utilizar el producto si su tapa
está quitada o no está bien cerrada.
8. Fusible neutro o de polo doble
Dos fusibles, uno en el polo y otro en el neutro. Quitar los cables de corriente antes de
abrir la tapa de este producto o tocar cualquier componente interno.
9. Tomas de alimentación múltiples
Riesgo de descarga eléctrica y peligro de corriente.
Todas las fuentes de alimentación son independientes.
Desconecte todas las fuentes de alimentación, para asegurar que no haya corriente
alguna dentro de la plataforma de conmutación.
10. Al haber rayos: peligro de descarga
No utilizar el equipo ni conectar o desconectar cables durante períodos de actividad de
rayos.
Mellanox Technologies
87
11. La conexión y desconexión de cables de cobre
Dado que los cables de cobre son pesados y no son flexibles, su conexión a los conectores y su desconexión se deben efectuar con mucho cuidado. Para ver advertencias o
instrucciones especiales, consultar al fabricante del cable.
12. Montaje y mantenimiento del bastidor
Al instalar o realizar el mantenimiento de este aparato en un bastidor, es preciso
adoptar precauciones especiales para garantizar que el sistema se mantenga estable. En
general, en un bastidor, los equipos se deben instalar comenzando desde abajo hacia
arriba.
13. Instalación del equipo
La instalación, el reemplazo y el mantenimiento de este equipo estarán a cargo únicamente de personal capacitado y competente.
14. Eliminación del equipo
La eliminación definitiva de este equipo se debe efectuar conforme a todas las leyes y
reglamentaciones nacionales.
15. Códigos eléctricos locales y nacionales
Este equipo se debe instalar conforme a los códigos eléctricos locales y nacionales.
16. Códigos de instalación
Este dispositivo se debe instalar conforme a la versión más reciente de los códigos
eléctricos nacionales del país en cuestión. En América del Norte, el equipo se debe
instalar de acuerdo con las disposiciones vigentes del Código Eléctrico Nacional de los
EE.UU. y del Código Eléctrico de Canadá.
17. Cambio de batería
II y a danger d’explosion s’il y a remplacement incorrect de la batterie. Remplacer
uniquement avec une batterie du même type ou d’un type équivalent recommandé par
le constructeur.
Mettre au rebut les batteries usagées conformément aux instructions du fabricant.
88
Mellanox Technologies
Rev 1.2
18. Cable de alimentación homologado por UL y con certificación CSA
En conexiones de América del Norte, seleccionar un cable de alimentación
homologado por UL y con certificación CSA de tres conductores, [16 AWG], terminado en un enchufe moldeado con capuchón de 125 voltios nominal, [13 A], con una
longitud mínima de 1,5 metros, pero no más de 4,5 metros.
En conexiones europeas, seleccionar un cable de alimentación armonizado
internacionalmente y marcado "<HAR>", de tres conductores, hilo de 1,0 mm2 como
mínimo, 300 voltios nominal, con cobertura protectora aislante de PVC. El cable debe
tener un enchufe moldeado con capuchón de 250 voltios nominal, 10 A.
19. Alta corriente de fuga
ADVERTENCIA: Alta corriente de fuga. Es esencial efectuar la conexión a tierra
antes de conectar la alimentación.
20. Códigos de instalación
Este dispositivo se debe instalar conforme a la versión más reciente de los códigos
eléctricos nacionales del país en cuestión. En América del Norte, el equipo se debe
instalar de acuerdo con las disposiciones vigentes del Código Eléctrico Nacional de los
EE.UU. y del Código Eléctrico de Canadá.
21. Interconexión de unidades
Los cables para la conexión con las interfaces RS232 y Ethernet de la unidad deben
estar homologados por UL tipo DP-1 o DP-2. (Nota: cuando residen en circuito no de
tipo LPS)
Protección contra sobrecargas: Al cableado del edificio se debe incorporar un dispositivo de protección contra sobrecargas de circuito derivado, de fácil acceso, con una
corriente nominal de 20 A.
22. No utilizar el conmutador como estante ni como espacio de trabajo
Cuidado: Equipos montados en deslizadores o rieles no se deben utilizar como estantes
ni como espacio de trabajo. La finalidad de los rieles no es deslizar la unidad hacia
afuera del bastidor. Sirven solo para la instalación permanente en el lugar de destino
final, no para fines de servicio o mantenimiento
23. Directiva WEEE
Conforme a la Directiva 2002/96/CE sobre RAEE, todos los residuos de equipos eléctricos y electrónicos (EEE) se deben recolectar por separado y no se deben eliminar
junto con residuos domésticos.
Al deshacerse de este producto y de todas sus partes, hágalo de una manera responsable y respetuosa con el medio ambiente.
Mellanox Technologies
89
E.8
Предупреждения по технике безопасности при установке (Russian)
1. Инструкция по установке
Перед подключением оборудования к источнику питания следует ознакомиться с
инструкцией по установке.
2. Травмы при переносе тяжелых предметов
Для поднятия этого изделия следует задействовать достаточное количество
людей.
<40 lbs
<18 kgs
40 - 70 lbs
18 - 32 kgs
70 - 121 lbs
32 - 55 kgs
>121 lbs
>55 kgs
3. Тяжелое оборудование
Это тяжелое оборудование, поэтому его следует перемещать с помощью
механического подъемника во избежание травм.
4. Опасность поражения электрическим током
Опасность поражения электрическим током!
Когда снят вентиляторный модуль, существует возможность повреждения
контактов питания в его углублении.
НЕ вставлять инструменты или части тела в углубление вентиляторного модуля.
5. Перегрев
Не эксплуатировать это оборудование в помещении с температурой окружающей
среды, превышающей максимально рекомендуемое значение: 45 °C (113 °F).
Более того, для надлежащей вентиляции следует обеспечить зазор вокруг
вентиляционных отверстий не менее 8 см (3 дюйма).
6. Установка шасси поверх другого оборудования
Не устанавливать шасси поверх другого оборудования. Падение шасси может
привести к травмам и повреждению оборудования.
90
Mellanox Technologies
Rev 1.2
7. Опасность поражения электрическим током резервного источника питания
В этом изделии установлен резервный источник питания или модуль-заглушка.
Если установлен модуль-заглушка, не эксплуатировать изделие со снятой или
ненадежно закрепленной крышкой модуля-заглушки.
8.
Двухполюсный предохранитель на фазном и нейтральном проводах
В этой системе установлен двухполюсный предохранитель на фазном и
нейтральном проводах. Открывать кожух этого изделия или касаться внутренних
деталей можно только после отсоединения всех шнуров питания.
9. Несколько источников питания
Опасность поражения электрическим током и опасные энергетические
воздействия.
Блоки питания независимы друг от друга.
Чтобы обесточить все компоненты внутри платформы коммутации, следует
отсоединить все блоки питания.
10. Опасность поражения электрическим током во время грозы
Во время грозы запрещается использовать оборудование и подключать или
отключать кабели.
11. Подсоединение и отсоединение медных кабелей
Медные кабели тяжелые и негибкие, поэтому следует осторожно их
подсоединять и отсоединять. За особыми предупреждениями и указаниями
следует обратиться к производителю кабеля.
12. Установка или обслуживание в стойке
При установке или обслуживании этого изделия в стойке следует обеспечить
устойчивость системы. Как правило, стойка заполняется оборудованием снизу
вверх.
13. Установка оборудования
Устанавливать, заменять и/или обслуживать это оборудование должен только
подготовленный и квалифицированный персонал.
Mellanox Technologies
91
14. Утилизация оборудования
Это оборудование утилизируется в соответствии с национальными законами и
постановлениями.
15. Местные и национальные правила установки электрооборудования
Это оборудование устанавливается в соответствии с местными и национальными
правилами установки электрооборудования.
16. Правила установки электрооборудования
Это устройство устанавливается в соответствии с последним изданием
национальных правил установки электрооборудования. В Северной Америке
оборудование устанавливается в соответствии с действующими требованиями
Национальных правил эксплуатации и обслуживания электрических установок
США и Канады.
17. Замена аккумулятора
Осторожно! Заменять только аккумулятором, одобренным организацией UL и
рассчитанным на максимальный аномальный зарядный ток не менее 4 мА.
Существует риск взрыва при замене аккумулятора другим аккумулятором
неправильного типа.
Отработавшие аккумуляторы утилизируются в соответствии с указаниями.
18. Шнур питания, включенный в номенклатуру UL и сертифицированный Канадской
ассоциацией стандартизации (CSA)
Подключение к электропитанию в Северной Америке выполняется с помощью
шнура питания, включенного в номенклатуру UL и сертифицированного
Канадской ассоциацией стандартизации (CSA), 3-жильного, [16 AWG], длиной
от 1,5 м [6 футов] до 4,5 м, с литой вилкой, рассчитанной на 125 В [13 А].
Подключение к электропитанию в Европе выполняется с помощью
гармонизированного шнура питания с маркировкой <HAR>, 3-жильного, с
сечением жилы не менее 1,0 мм², рассчитанного на номинальное напряжение 300
В, с ПВХ оболочкой. Шнур должен иметь литую вилку, рассчитанную на 250 В,
10 А.
19. Высокий ток утечки
Осторожно! Высокий ток утечки. Заземлить перед подключением к
электропитанию.
92
Mellanox Technologies
Rev 1.2
20. Правила установки электрооборудования
Это устройство устанавливается в соответствии с последним изданием
национальных правил установки электрооборудования. В Северной Америке
оборудование устанавливается в соответствии с действующими требованиями
Национальных правил эксплуатации и обслуживания электрических установок
США и Канады.
21. Подсоединение устройств
Для подключения к разъемам RS232 и Ethernet используются кабели типа DP-1
или DP-2, сертифицированные организацией UL. (Примечание. При
подключении к сети без ограниченного источника электропитания)
Максимальная токовая защита. В проводку здания в легкодоступном месте
следует включить устройство защиты от перегрузки по току номиналом 20 А.
22. Не использовать коммутатор как полку или рабочую
Внимание! Оборудование, установленное на направляющих, не должно
использоваться как полка или рабочая поверхность. Направляющие не
предназначены для удерживания устройства, выдвинутого из стойки. Они
предназначены для стационарной установки только в конечном положении и не
используются для обслуживания устройства.
23. Директива WEEE
В соответствии с Директивой 2002/96/EC (WEEE) отходы электрического и
электронного оборудования должны собираться и утилизироваться отдельно от
обычных бытовых отходов.
Следует утилизировать это изделие и все его части ответственным и
экологически безопасным способом.
E.9
Avertismente privind siguranţa la instalare (Romanian)
1. Instrucţiuni de instalare
Citiţi toate instrucţiunile de instalare înainte de a conecta.
Mellanox Technologies
93
2. Accidentare cauzată de greutate
Apelaţi la un număr suficient de persoane pentru a ridica în siguranţă acest produs.
<40 lbs
<18 kgs
3.
40 - 70 lbs
18 - 32 kgs
70 - 121 lbs
32 - 55 kgs
>121 lbs
>55 kgs
Echipament greu
Acest echipament este greu şi trebuie să fie mutat folosind un dispozitiv mecanic de
ridicare pentru a evita producerea de leziuni.
4.
Risc de şoc electric
Risc de şoc electric!
Odată ce modulul ventilator este îndepărtat, pinii electrici sunt accesibili în cavitatea
modulului.
NU introduceţi instrumente sau părţi din corp în cavitatea modulului ventilator.
5.
Temperatură în exces
Acest echipament nu trebuie să fie acţionat într-o zonă unde temperatura ambiantă
depăşeşte valoarea maximă recomandată: 45°C (113°F). În plus, pentru a asigura un
flux de aer adecvat, lăsaţi un spaţiu liber de cel puţin 8 cm (3 inchi) în jurul fantelor de
ventilare.
6. Suprapunerea cadrului
Cadrul nu trebuie să fie suprapus peste niciun alt echipament. În cazul în care cadrul
cade, poate cauza leziuni corporale şi deteriorări ale echipamentului.
7. Conexiunea la o sursă de alimentare electrică suplimentară - pericol electric
Acest produs include o sursă de alimentare suplimentară sau un spaţiu gol în locul
acesteia. În cazul în care spaţiul pentru sursa de alimentare este gol, nu operaţi produsul când capacul orb este îndepărtat sau nu este fixat în mod sigur.
94
Mellanox Technologies
Rev 1.2
8.
Siguranţă fuzibilă bipolară/neutră
Acest sistem este prevăzut cu siguranţă fuzibilă bipolară/neutră. Îndepărtaţi toate cordoanele de alimentare înainte de a deschide capacul acestui produs sau înainte de a
atinge orice componente interne.
9. Multiple mufe electrice
Risc de şoc electric şi pericol electric.
Toate aparatele cu alimentare de la reţea sunt independente.
Deconectaţi toate sursele de alimentare cu energie pentru a asigura decuplarea în interiorul platformei de comutare.
10. În timpul descărcărilor electrice - pericol electric
În timpul perioadelor cu descărcări electrice luminoase, nu lucraţi cu echipamentul sau
nu conectaţi sau deconectaţi cablurile.
11. Conectarea/deconectarea cablului din cupru
Cablurile din cupru sunt grele şi inflexibile, de aceea trebuie să fie ataşate sau detaşate
de conectori cu grijă. Consultaţi producătorul de cabluri pentru avertismente/instrucţiuni speciale.
12. Montarea sau depanarea într-un rack
Când acest produs este montat sau depanat într-un rack, trebuie să fie luate măsuri de
precauţie speciale pentru a se asigura că sistemul rămâne stabil. În general, trebuie să
umpleţi rack-ul cu echipamente începând de jos în sus.
13. Instalarea echipamentului
Acest echipament trebuie să fie instalat, înlocuit şi/sau depanat numai de către personal
instruit şi calificat.
14. Eliminarea echipamentului
Eliminarea acestui echipament trebuie să se realizeze în conformitate cu toate legile şi
regulamentele naţionale.
Mellanox Technologies
95
15. Codurile electrice locale şi naţionale
Acest echipament trebuie să fie instalat conform codurilor electrice locale şi naţionale.
16. Codurile ed instalare
Acest dispozitiv trebuie să fie instalat în conformitate cu ultima versiune a codurilor
electrice naţionale ale ţării în cauză. Pentru America de Nord, echipamentul trebuie să
fie instalat conform cerințelor aplicabile din Codul electric naţional al SUA şi Codul
electric canadian.
17. Înlocuirea bateriei
Avertisment: Înlocuiţi numai cu o baterie recunoscută UL, certificată pentru curent de
încărcare anormal maxim de minimum 4 mA
Există risc de explozie în cazul în care bateria este înlocuită cu o baterie necorespunzătoare.
Eliminaţi bateriile folosite în conformitate cu instrucţiunile.
18. Cordon de alimentare electrică înregistrat UL şi certificat CSA
Pentru conectarea la o sursă de alimentare pentru America de Nord, selectaţi un cordon
de alimentare care este înregistrat UL şi certificat CSA, cu 3 conductoare, [16 AWG],
terminat cu o fişă turnată, cu putere nominală egală cu 125 V, [13 A], cu o lungime de
minimum 1,5 m [şase picioare], dar nu mai lung de 4,5 m.
Pentru conectarea la o sursă de alimentare în Europa, selectaţi un cordon de alimentare
care este armonizat la nivel internaţional şi marcat „<HAR>”, cu 3 conductoare, cu
minimum 2 fire de 1,0 mm, cu putere nominală egală cu 300 V şi cu o manta izolantă
din PVC. Cordonul de alimentare trebuie să fie prevăzut cu o fişă turnată cu putere
nominală egală cu 250 V, 10 A.
19. Curent de scurgere de înaltă frecvenţă
Avertisment: Curent de scurgere de înaltă frecvenţă; Împământarea este esenţială
înainte de a conecta sursa de alimentare.
20. Codurile de instalare
Acest dispozitiv trebuie să fie instalat în conformitate cu ultima versiune a codurilor
electrice naţionale ale ţării în cauză. Pentru America de Nord, echipamentul trebuie să
fie instalat conform cerințelor aplicabile din Codul electric naţional al SUA şi Codul
electric canadian.
96
Mellanox Technologies
Rev 1.2
21. Interconectarea unităţilor
Cablurile pentru conectarea la unitatea RS232 şi la interfeţele Ethernet trebuie să fie de
tipul DP-1 sau DP-2 certificate UL. (Notă- când se regăsesc într-un circuit non-LPS)
Protecţie la supracurent: Un dispozitiv de protecţie la supracurent, înregistrat în circuitul de ramificare, uşor accesibil şi cu o putere nominală egală cu 20 A trebuie să fie
integrat în cablajul clădirii.
22. Nu utilizaţi comutatorul ca raft sau spaţiu de lucru
Atenţie: Echipamentul montat pe o linie de alunecare/şină nu va fi utilizat ca raft sau
spaţiu de lucru. Scopul şinelor nu este de a glisa unitatea de pe rack. Acestea sunt destinate instalării permanente numai la punctul final de oprire şi nu vor fi folosite pentru
depanare şi întreţinere
23. Directiva DEEE
În conformitate cu Directiva DEEE 2002/96/CE, toate deşeurile de echipamente electrice şi electronice (EEE) trebuie colectate separat şi nu trebuie eliminate împreună cu
deşeurile menajere obişnuite.
Eliminaţi acest produs şi toate componentele sale în mod responsabil şi ecologic.
24. RestrictionsRestricţii electrice pentru Norvegia
This unit is intended for connection to a TN power system and an IT power system of
Norway only.
E.10 Sigurnosna upozorenja za instaliranje (Croatian)
1. Upute za instaliranje
Pažljivo pročitajte upute za instaliranje prije spajanja opreme na izvor električne
energije.
Mellanox Technologies
97
2. Tjelesne ozljede uslijed težine
Kako biste sigurno podignuli ovaj proizvod, koristite dovoljan broj ljudi.
<40 lbs
<18 kgs
3.
40 - 70 lbs
18 - 32 kgs
70 - 121 lbs
32 - 55 kgs
>121 lbs
>55 kgs
Teška oprema
Ova oprema je vrlo teška i treba se premještati pomoću mehaničkog dizala kako bi se
izbjegle ozljede.
4. Rizik od strujnog udara!
Rizik od strujnog udara!
S uklonjenim modulom ventilatora, perima napajanja se može pristupiti u otvoru modula.
NEMOJTE umetati alat ili dijelove tijela u otvor modula ventilatora.
5. Pregrijavanje
Ovom se opremom ne bi trebalo rukovati u područjima s temperaturom okoline koja
premašuje najviše preporučene vrijednosti: 45°C (113°F). Osim toga, kako bi se osigurao odgovarajući protok zraka, omogućite najmanje 8 cm (3 inča) razmaka oko otvora
ventilatora.
6. Slaganje kućišta
Kućište se ne bi trebalo slagati na drugu opremu. Ako kućište padne, može izazvati tjelesne ozljede i oštećenje opreme.
7. Redundantno napajanje - Opasnost od električne energije
Ovaj proizvod uključuje redundantno napajanje ili prazan prostor na njegovu mjestu.
U slučaju praznog prostora za napajanje, nemojte rukovati proizvodom ako je poklopac uklonjen ili ako nije dobro pričvršćen.
98
Mellanox Technologies
Rev 1.2
8. Dvopolni/neutralni osigurači
Ovaj sustav raspolaže dvopolnim/neutralnim osiguračima. Uklonite sve kabele napajanja prije otvaranja poklopca proizvoda ili dodirivanja unutarnjih dijelova.
9. Višestruki ulazi za napajanje
Rizik od strujnog udara i opasnost od električne energije.
PSU jedinice su neovisne.
Odspojite sva napajanja kako biste osigurali stanje bez napajanja unutar platforme
preklopnika.
10. Tijekom udara munje - Opasnost od električne energije
Tijekom djelovanja munja, nemojte raditi na opremi ili spajati ili odspajati kabele.
11. Spajanje/Odspajanje bakrenog kabela
Bakreni kabeli su teški i nesavitljivi i kao takvi se moraju pažljivo priključiti na ili isključiti iz konektora. Obratite se proizvođaču kabela za posebna upozorenja/upute.
12. Montaža ormarića i servisiranje
Kad se proizvod montira ili se servisira u ormariću, moraju se poduzeti posebne mjere
opreza kako bi se osiguralo da sustav ostane stabilan. Općenito, trebali biste ispunjavati ormarić s opremom počevši od dna prema vrhu.
13. Instaliranje opreme
Ovu bi opremu trebalo instalirati, zamjenjivati i/ili servisirati samo obučeno i kvalificirano osoblje.
14. Odlaganje opreme
Odlaganje opreme trebalo bi se vršiti sukladno nacionalnim zakonima i propisima.
Mellanox Technologies
99
15. Lokalni i nacionalni električni kodovi
Ova oprema trebala bi se instalirati u skladu s lokalnim i nacionalnim električnim
kodovima.
16. Instalacijski kodovi
Ovaj se uređaj mora instalirati sukladno najnovijoj verziji nacionalnih električnih kodova države. U Sjevernoj Americi oprema se mora instalirati sukladno važećim zahtjevima navedenim u US National Electrical Code i
Canadian Electrical Code.
17. Zamjena baterije
Upozorenje: Bateriju zamijenite samo baterijom iz serije UL koja je certificirana za maksimalnu nepravilnu struju punjenja ne manju od 4 mA
Postoji rizik od eksplozije ako se baterija zamijeni neodgovarajućom vrstom.
Odložite prazne baterije sukladno uputama.
18. UL CSA kabel napajanja
Za sjevernoameričku mrežu odaberite kabel napajanja koji je na UL listi i sa
CSA certifikatom, 3 - žilni, [16 AWG] (16 AWG) koji završava lijevanim utikačem nazivnog napona od 125 V, [13 A], minimalne duljine od 1,5 m [six
feet] (šest stopa), ali ne dulji od 4,5 m.
Za europsku mrežu odaberite kabel napajanja koji je međunarodno usklađen i
označen “<HAR>”, 3 - žilni, s najmanje 1,0 mm2 žice, nazivnog napona od
300 V, s PVC izolacijom. Kabel mora imati lijevani utikač nazivnog napona od
250 V, nazivne struje od 10 A.
19. Veliko curenje struje
Upozorenje: Veliko curenje struje; Prije spajanja napajanja nužno je spojiti uzemljenje.
20. Instalacijski kodovi
Ovaj se uređaj mora instalirati sukladno najnovijoj verziji nacionalnih električnih
kodova države. U Sjevernoj Americi oprema se mora instalirati sukladno važećim
zahtjevima navedenim u US National Electrical Code i Canadian Electrical Code.
100
Mellanox Technologies
Rev 1.2
21. Interkonekcija uređaja
Kabeli za spajanje na jedinicu RS232 i Ethernet sučelja moraju biti s UL certifikatom vrste DP-1 ili DP-2. (Napomena - kad se nalazi u krugu bez LPS
vodiča)
Zaštita od strujnog preopterećenja: Uvijek dostupni odobreni zaštitni uređaji
od strujnog preopterećenja nazivne struje od 20 A moraju se ugraditi u
ožičenje zgrade.
22. Nemojte koristiti preklopnik kao policu ili radnu površinu
Pozor: Oprema montirana na klizače/vodilice ne bi se trebala koristiti kao polica ili
radna površina. Vodilice nisu namijenjene za povlačenje uređaja iz ormarića. Služe
samo za trajnu instalaciju na konačnom položaju, a ne za servisiranje i održavanje.
23. WEEE direktiva
Sukladno WEEE direktivi 2002/96/EZ, sav električni i elektronički otpad (EEE) trebao
bi se prikupljati zasebno i ne bi se trebao odlagati kao običan kućanski otpad.
Odlaganje ovog proizvoda i svih njegovih dijelova vršite na odgovoran i ekološki
način.
24. Električna ograničenja države Norveške
Ovaj je uređaj namijenjen samo za spajanje na električni sustav s TN uzemljenjem i na
električni sustav s IT uzemljenjem države Norveške.
E.11
Avvertenze di sicurezza per l’installazione (Italian)
1. Istruzioni di installazione
Leggere tutte le istruzioni di installazione prima di collegare l’apparecchiatura
all’alimentazione.
Mellanox Technologies
101
2. Lesioni a causa del peso
Usare un numero di persone sufficiente per sollevare in sicurezza questo prodotto.
<40 lbs
<18 kgs
3.
40 - 70 lbs
18 - 32 kgs
70 - 121 lbs
32 - 55 kgs
>121 lbs
>55 kgs
Apparecchiatura pesante
Questa apparecchiatura è molto pesante e va spostata mediante un sollevatore
meccanico, per evitare lesioni.
4. Rischio di scosse elettriche!
Rischio di scosse elettriche!
Con il modulo ventola rimosso, i pin di alimentazione sono accessibili all’interno della
cavità del modulo.
NON inserire strumenti o parti del corpo nella cavità del modulo della ventola.
5. Temperatura eccessiva
Questa apparecchiatura non va utilizzata in un’area con una temperatura ambiente
superiore a quella massima consigliata: 45 °C (113 °F). Inoltre, per assicurare un
flusso d’aria adeguato, lasciare almeno 8 cm (3 pollici) di spazio attorno alle aperture
di ventilazione.
6. Impilare lo chassis
Kućište se ne bi trebalo slagati na drugu opremu. Ako kućište padne, može izazvati tjelesne ozljede i oštećenje opreme.
7. Collegamento di alimentazione ridondante - Pericoli elettrici
Questo prodotto è dotato di un alimentatore ridondante o, qualora esso non sia
installato, di uno spazio vuoto. Qualora l’alimentatore non sia installato, non utilizzare
il prodotto con il coperchio rimosso o non fissato correttamente.
102
Mellanox Technologies
Rev 1.2
8. Fusibili fase/neutro
Questo sistema dispone di fusibili fase/neutro. Rimuovere tutti i cavi di alimentazione
prima di aprire il coperchio di questo prodotto o di toccare parti interne.
9. Prese di alimentazione multiple
Rischio e pericolo di scosse elettriche.
Gli alimentatori sono tutti indipendenti.
Scollegare tutti gli alimentatori per assicurarsi che il commutatore non sia sotto
tensione
10. Durante i temporali, pericolo di scosse elettriche
Durante i temporali, non effettuare interventi sull’apparecchiatura e non collegare o
scollegare i cavi.
11. Collegamento/scollegamento del cavo di rame
I cavi di rame sono pesanti e non flessibili. Di conseguenza, vanno
collegati o scollegati con cura dai connettori. Per avvertenze/istruzioni speciali,
rivolgersi al produttore di cavi.
12. Montaggio su rack e manutenzione
Quando questo prodotto viene montato o sottoposto a manutenzione su un rack, è
necessario adottare delle precauzioni speciali per assicurarsi che il sistema resti stabile.
In generale, il rack va riempito con apparecchiature, procedendo dal basso verso l’alto.
13. Installazione dell’apparecchiatura
Questa apparecchiatura va installata, sostituita e/o sottoposta a manutenzione solo da
personale addestrato e qualificato.
14. Smaltimento dell’apparecchiatura
Lo smaltimento di questa apparecchiatura va effettuato in conformità con tutte le leggi
e le normative nazionali.
Mellanox Technologies
103
15. Codici elettrici locali e nazionali
Questa apparecchiatura va installata in conformità con le norme elettriche locali e
nazionali.
16. Codici di installazione
Questo dispositivo va installato in conformità con l’ultima versione dei codici elettrici
nazionali del Paese. Per il Nord America, l’apparecchiatura va installata in conformità
con i requisiti applicabili del “codice elettrico nazionale USA” e del “codice elettrico
canadese”.
17. Sostituzione della batteria
Avvertenza: Sostituire solo con una batteria UL, certificata per accettare una
corrente di ricarica anomala massima non inferiore a 4 mA.
Se la batteria non viene sostituita con una batteria di tipo corretto, vi è il rischio
di esplosione.
Smaltire le batterie usate in conformità con le istruzioni.
18. Cavo di alimentazione UL e munito di certificazione CSA
Per una connessione di alimentazione nordamericana, selezionare un cavo di
alimentazione di tipo UL e munito di certificazione CSA, a 3 conduttori, [16 AWG],
terminato con una spina stampata con tensione nominale pari a 125 V, [13 A], di
lunghezza minima pari a 1,5 m [sei piedi] ma non più lunga di 4,5 m.
Per una connessione europea, selezionare un cavo di alimentazione armonizzato a
livello internazionale e contrassegnato da “<HAR>”, a 3 conduttori, minimo 1,0 mm2
fili, con guaina isolante in PVC. Il cavo deve disporre di una spina stampata di potenza
nominale pari a 250 V, 10 A.
19. Corrente di dispersione elevata
Avvertenza: corrente di dispersione elevata; il collegamento a terra è essenziale prima
di collegare l’alimentazione.
20. Codici di installazionei
Questo dispositivo va installato in conformità con l’ultima versione dei codici elettrici
nazionali del Paese. Per il Nord America, l’apparecchiatura va installata in conformità
con i requisiti applicabili del “codice elettrico nazionale USA” e del “codice elettrico
canadese”.
104
Mellanox Technologies
Rev 1.2
21. Interconnessione delle unità
I cavi per il collegamento all’unità RS232 e alle interfacce Ethernet devono
disporre della certificazione UL ed essere del tipo DP-1 o DP-2. (Nota: in caso
di installazione su un circuito la cui potenza non è limitata)
Protezione contro le sovracorrenti: la cablatura dell’edificio deve integrare un
dispositivo di protezione contro le sovracorrenti di potenza nominale pari a 20.
22. Non utilizzare lo switch come scaffale o piano di lavorol
Attenzione: un’apparecchiatura scorrevole o montata su binari non va utilizzata come
scaffale o piano di lavoro. I binari non sono progettati per far scorrere e allontanare
l’unità dal rack. Essi sono destinati all’installazione permanente solo nel luogo di
lavoro e non vengono utilizzati per assistenza e manutenzione
23. Direttiva RAEE
Secondo la direttiva RAEE 2002/96/EC, tutti i rifiuti da apparecchiature elettriche ed
elettroniche (RAEE) vanno raccolti separatamente e non smaltiti nei normali rifiuti
domestici.
Smaltire questo prodotto e tutte le sue parti in modo responsabile e rispettoso
dell’ambiente
24. Limitazioni relative all’alimentazione per la Norvegia
Questa apparecchiatura è progettata esclusivamente per il collegamento a un sistema di
alimentazione TN e a un sistema di alimentazione IT.
E.12 Montaj Güvenlik Uyarıları (Turkish)
1. Montaj Talimatları
Ekipmanı güç kaynağına bağlamadan önce tüm montaj talimatlarını okuyun.
Mellanox Technologies
105
2. Ağırlık Nedeniyle Fiziksel Yaralanma
Bu ürünü güvenli bir şekilde kaldırabilmek için yeterli sayıda insandan yardım alın.
<40 lbs
<18 kgs
40 - 70 lbs
18 - 32 kgs
70 - 121 lbs
32 - 55 kgs
>121 lbs
>55 kgs
3. Ağır Ekipman
Bu ekipman çok ağırdır ve yaralanmaları önlemek için ekipmanın mekanik asansör
kullanılarak taşınması gerekir.
4. Elektrik Çarpması Riski!
Bu ekipman, önerilen maksimum ortam sıcaklığını aşan alanlarda çalıştırılmamalıdır:
45 °C (113 °F). Ayrıca, düzgün hava akışı sağlamak için havalandırma deliklerinin
etrafında en az 8 cm (3 inç) açıklık bırakılmalıdır.
5. Aşırı ısınma
Bu ekipman, önerilen maksimum ortam sıcaklığını aşan alanlarda çalıştırılmamalıdır:
45 °C (113 °F). Ayrıca, düzgün hava akışı sağlamak için havalandırma deliklerinin
etrafında en az 8 cm (3 inç) açıklık bırakılmalıdır.
6. Şasi İstif
Şasinin diğer herhangi bir ekipmanın üzerine istiflenmemesi gerekir. Şasi düşerse,
fiziksel yaralanmalara ve ekipmanda hasara neden olabilir.
7. Yedekli Güç Kaynaðý Baðlantýsý -Elektrik Çarpma Tehlikesi
Bu ürün, yedekli güç kaynağı veya onun yerine boş elektrik kutusu içerir. Güç kaynağı
için boş elektrik kutusu varsa, kutunun kapağı açıkken veya tam olarak
kapatılmamışken ürünü çalıştırmayın.
106
Mellanox Technologies
Rev 1.2
8. Çift Kutuplu/Nötr Kesmeli Sigorta
Bu sistemde çift kutuplu/nötr kesmeli sigorta kullanılmaktadır. Ürünün kapağını
açmadan veya herhangi bir iç parçaya dokunmadan önce bütün güç kablolarını
çıkartın.
9. Çoklu Güç Girişleri
Elektrik çarpması riski ve enerji tehlikesi.
Bütün PSU'lar (Güç Kaynağı Üniteleri) ayrıdır.
Anahtar platformundaki gücü kapatmak için tüm güç kaynaklarının bağlantılarını
kesin.
10. Şimşek - Elektrik Çarpma Tehlikesi
Gökyüzünde şimşek çaktığı zamanlarda, ekipman üzerinde çalışmayın veya kablo
bağlamayın ya da kablo bağlantısı kesmeyin.
11. İskele Montajı ve Bakım
Bu ürün bir iskelede monte edildiyse veya bir iskele ile sunulduysa, sistemin sabit
kalması için özel önlemler alınmalıdır. Genelde, ekipmanları iskeleye aşağıdan yukarı
doğru doldurmanız gerekir.
12. Ekipman Montajı
Ekipmanın yalnızca eğitimli ve nitelikli personel tarafından monte edilmesi,
değiştirilmesi ve/veya bakımının yapılması gerekir.
13. Ekipmanın Atılması
Bu ekipmanın imhasında tüm ulusal yasalara ve düzenlemelere uyulması gerekir.
14. Yerel ve Ulusal Elektrik Kodları
Bu ekipmanın montajında yerel ve ulusal elektrik kodlarına uyulması gerekir.
Mellanox Technologies
107
15. Montaj Kodları
Bu cihazın, ülke ulusal elektrik kodlarının son sürümüne göre monte edilmesi
gerekir. Kuzey Amerika için, ekipmanın ABD Ulusal Elektrik Kodu ve
Kanada Elektrik Kodu'nun uygulama koşullarına göre monte edilmesi gerekir.
16. Pilin Değiştirilmesi
Uyarı: Yalnızca, maksimum düzgüsüz şarj akımı 4mA'dan az olmayan, UL
Onaylı pillerle değiştirin.
Yanlış pil türü ile değiştirildiğinde patlama tehlikesi bulunmaktadır.
Kullanılmış pillerden talimatlara uygun bir şekilde kurtulun.
17. UL Kayıtlı ve CSA Onaylı Güç Kaynağı Kablosu
Kuzey Amerika'da güç bağlantısı için, UL Kayıtlı ve CSA Onaylı bir güç kaynağı
kablosu seçin, 3 - iletken, [16 AWG], 125 V değerinde, kalıplanmış bir fişle biten,
[13 A], en az 1,5 m (altı fit) uzunluğunda fakat 4,5 m'den uzun olmayan bir kablo.
Avrupa'da güç bağlantısı için, uluslararası uyumlu ve “<HAR>” işaretli,
3 - iletken, en az 1,0 mm2 tel, 300 V değerinde ve PVC yalıtımlı bir güç
kaynağı kablosu seçin. Kablonun 250 V, 10 A değerinde bir kalıplanmış fişi
olması gerekmektedir.
18. Yüksek Kaçak Akım
Yüksek kaçak akım varsa; güç kaynağına bağlanmadan önce mutlaka topraklama
bağlantısı yapılmalıdır.
19. Montaj Kodlarıi
Bu cihazın, ülke ulusal elektrik kodlarının son sürümüne göre monte edilmesi gerekir.
Kuzey Amerika için, ekipmanın ABD Ulusal Elektrik Kodu ve Kanada Elektrik
Kodu'nun uygulama koşullarına göre monte edilmesi gerekir.
20. Ünitelerin Ara Bağlantısı
RS232 ünitesini ve Ethernet Arabirimlerini bağlayacak olan kabloların UL
onaylı DP-1 veya DP-2 tipi olması gerekir. (Not- LPS olmayan devreye aitse)
Aşırı Akım Koruması: Kolayca erişilebilecek 20 V Kayıtlı devre parçası aşırı
akım koruma cihazının bina elektrik şebekesinde kurulu olması gerekir.
21. Anahtarı Raf veya Çalışma Alanı olarak kullanmayınl
Dikkat: Sürgülü/raylı ekipman raf veya çalışma alanı olarak kullanılamaz. Raylar
üniteyi iskeleden uzağa kaydırmak için yapılmamıştır. Sadece, ekipmanın son olarak
duracağı yerdeki kalıcı montaj içindir, servis veya bakım için kullanılamaz.
108
Mellanox Technologies
Rev 1.2
22. WEEE Yönergesi
WEEE Yönergesi 2002/96/EC uyarınca, tüm elektrikli ve elektronik ekipman atıkları
(EEE) ayrı olarak toplanmalı ve evsel atıklarla birlikte çöpe atılmamalıdır.
Bu ürün ve tüm parçaları çevreye dost ve sorumlu bir şekilde imha edilmelidir.
23. Norveç Güç Kısıtlamaları
Bu ünite, bir TN güç sistemine ve sadece Norveç'in IT güç sistemine bağlanmak
içindir.
E.13 Japan VCCI Statement
Mellanox Technologies
109
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising