view product Specification in format - COP

view product Specification in  format - COP
8 Ports PoE Ethernet Switch
User Manual
8 ports PoE Ethernet Switch is a security surveillance Ethernet Switch which aims at Ethernet
high definitio surveillance and Ethernet project security system .The product fully combines
the characteristics of security surveillance, provides fast packet forwarding ability and
abundant backplane bandwidth, which ensures clear image and fuent transmission.
The product supports one key Extend model, can achieve VLAN, control the Net storm,
protect the information security, prevent the viral transmission and Ethernet attack, fully
satisfy the Ethernet video security surveillance system and Ethernet project needs.
8 Ports PoE Ethernet Switch
Board Diagram
Front board
Link/Active
PWR
Function
Function Ethernet PoE Switch
POE Ethernet Port
Up-link Ethernet Port
Application
8P
o rts
PoE
Back board
E
het r
n
et
Sw
it c h
p ower
Mo
nit
or
C
ON / OFF
a
t5
N
e
/5
DC48V
R
V
/6
C
ab
PoE IP Camera
le
PoE Dome C amera
Swtich on,it will support Vlan and
200meter with 10mbps transmssion
Power input port
PoE IP Camera
PoE PTZ Camera
Notice
Pls re-start device before turn on function
Feature
Support for Vlan :1-8 POE port will not communicate with each other, POE port only
communicate with uplink port.It will control the Net storm, protect the information security.
Transmission :1-8 port can be 100meters with 100mbps or 200meters with
10mbps. Uplink port will be 100meters with 100mbps.
Conforms to IEEE802.3, IEEE 802.3u, IEEE802.3af, IEEE802.3at
Provides 9 10/100Base-TX ports
Provides 8 PoE injector and 130W power adapter
High back-plane bandwidth 1.8Gbps
IEEE802.3x Flow control
Surge protection for power port and data ports
Notice
The transmission distance is related to the connected cable. We suggest standard
Cat5e, 6 network cable and quality of camera! so the transmission distance can up tofurthest/
1
Installation steps
Please check the following items before installation, if t is missing , please contact the
dealer.
8 ports PoE Ethernet Switch
1pcs
Power adaptor
1pcs
AC power cable
1pcs
Accessory
1pcs
User manual
1pcs
Please follow the below installation steps
1 Please turn off the signal power and display device power before installation, installation
with power will damage the transmission equipment;
2 Use network cable connect PoE IP camera and 1~8 downlink ports of product respectively
3 Use a network cable connect equipment up link port and NVR or computer
;
;
4 Connect power adapter
5 Check if the installation is correct equipment is in good condition the connection is stable
then provide power for system
;
6 Ensure the Ethernet equipment with power and work properly
2
8 Ports PoE Ethernet Switch
8 Ports PoE Ethernet Switch
Trouble Shooting
Specificatio
Item
Power
Description
Power Supply
External Power Adaptor
Voltage Range
DC48V~52V
Consumption
<6W
Speed
1-8 Port:10/100Mbps
Uplink:100Mbps
Ethernet
1-8port 100Meters with 100Mpbs
Transmission Distance
200Meters with 10Mbps
Uplink:100Meter with 100Mpbs
Network Switch
Ethenet Standard
IEEE 802.3 802.3u 802.3af at
Switching capacity
1.8G
14,880 pps for 10Mbps
Transfer Rate
148,800 pps for 100Mbps
MACAddress
Function
LINK/ACT
On
Green
On
Green
Blinks
Off
PoE
(12.36)
Working
Environment
1K MAC address table
Instruments to be used, wire crimper. network tester: Wire sequence of RJ45 plug should
conform with EIA/TIA568A or 568B.
1 Please remove 2cm long the insulating layer and bare 8 pairs UTP cable
2 Separate the 8 pairs UTP cable and straighten them
3 Line up the 8 pieces of cables per EIA TIA 568A or 568B
4 Cut off the cables to leave 1 5cm bare wire
5 Plug 8 cables into RJ45 plug make sure each cable is in each pin
6 Use the wire crimper to crimp it
7 Repeat above 9 steps to make the another end
8 Use network tester to test the cable if t works
-
Pin
-
The port is not linked successfully with the device
.
1
PD is connected
Color
1
8
Pin
Color
1
White/Green
1
White/Orange
2
Green
2
Orange
3
White/Orange
3
White/Green
No PD is connected or power forwarding fails
4
Blue
4
Blue
Working Temperature
0℃~40 ℃
5
White/Blue
5
White/Blue
Storage Temperature
-40℃~ 70℃
6
Orange
6
Green
0~85 %
7
White/Brown
7
White/Brown
8
Brown
8
Brown
Off
-
Humidity-Non
) condesing
(
Dimension L W H
Mechanical
The port is connecting
.
Plug Producing Method
The port is receiving or transmitting data.
Orange
On
The vlan and 200meters is start to work
Please follow the steps if the equipment has trouble
.
Make sure the equipment is installed according to the manufactures installation
. guide
Confir RJ45 cable order meets EIA TIA568A
/
or 568B standard .
Every PoE port can provide PoE equipment maximum power less than 30W, please do not
connect the PoE equipment with power over .30W
Replace the equipment with a proper functioning 8 ports PoE Ethernet Switch to check if
the equipment is damaged
.
Please contact your vendor if trouble still exists
.
218mm×107x29mm
Out Shell
Galvanized Sheet
Color
Gray
EIA/TIA 568A
8
EIA/TIA 568B
Notice
When choose RJ45 make sure if one end is EIA/TIA568A,the other end should also be EIA/TIA568A.
When choose RJ45 make sure if one end is EIA/TIA568B,the other end should also be EIA/TIA568B.
Specificatio change will not be noticed
3
4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising