Metasys CCT Bluetooth Technology Communication

Metasys CCT Bluetooth Technology Communication
Metasys® CCT Bluetooth® Technology Communication
Commissioning Guide
MS-BTCVT-1 (Wireless Commissioning Converter)
Code No. LIT-12011038
Software Release 10.1
Issued December 5, 2014
Refer to the QuickLIT website for the most up-to-date version of this document.
Document Introduction.............................................................................................................2
Concepts.....................................................................................................................................2
Bluetooth Wireless Technology Modules and Adapters.................................................................2
Bluetooth Quick Start Guide.....................................................................................................3
Troubleshooting.........................................................................................................................9
Detailed Procedures................................................................................................................11
Verifying the Connection between the Laptop and the Wireless Commissioning Converter....11
Installing the Bluetooth Wireless USB Adapter.............................................................................13
Related Documentation...........................................................................................................14
Metasys® CCT Bluetooth® Technology Communication Commissioning Guide
1
Document Introduction
This document describes how to install the supported Bluetooth® wireless adapters and commission your Controller
Configuration Tool (CCT) laptop or desktop computer to communicate with the Bluetooth Wireless Commissioning
Converter (BTCVT).
Note: In other documentation, the Wireless Commissioning Converter may be referred to as the Bluetooth
Commissioning Converter.
This document assumes that you have already installed the CCT software on your computer.
Metasys® CCT supports the Windows 8.1, Windows 8, and Windows 7 operating systems. Windows XP® is no
longer supported for CCT software at Release 10.1.
Note: You cannot commission your CCT laptop or desktop for Bluetooth communication if it is running a server-class
operating system, such as Windows Server® 2008 or Windows Server 2012.
To complete all of the procedures in this document, you must also have a Wireless Commissioning Converter
connected to a powered-on field controller (refer to the Wireless Commissioning Converter Installation Instructions
[Part No. 24-10108-2]).
Note: The Wireless Commissioning Converter can be used in conjunction with the ZFR1800 Series Wireless Field
Bus System; however, the wireless technologies of the Wireless Commissioning Converter and the ZFR1800
Series System do not directly interact. When the Wireless Commissioning Converter is connected on the
hard-wired portion of a Field Controller (FC) Bus, it can be used to commission and communicate with any
field controller, whether it is hardwired to the FC Bus or wirelessly enabled through the ZFR1800 Series
Wireless Field Bus System. When the Wireless Commissioning Converter is connected directly to a wirelessly
enabled field controller, it commissions and communicates with only that controller.
Concepts
Bluetooth Wireless Technology Modules and Adapters
Bluetooth allows the CCT software to connect the Wireless Commissioning Converter for uploading and downloading
field controller applications.
The computer that is running CCT must have Bluetooth wireless capabilities to communicate with the Wireless
Commissioning Converter. We recommend that you do not install an external Bluetooth wireless adapter if Bluetooth
technology is already built in.
You can commission the following types of laptop computers to communicate with the Wireless Commissioning
Converter:
•
•
a laptop computer with an internal Bluetooth wireless module
a laptop or desktop computer with a Bluetooth wireless USB adapter
If you do not have Bluetooth technology built in to your computer and you must install a Bluetooth wireless USB
adapter, see Installing the Bluetooth Wireless USB Adapter for directions. After the Bluetooth wireless adapter is
installed and configured, you do not need to configure it again until software or hardware configurations change.
For the latest list of laptop computers with internal Bluetooth wireless modules and USB adapters, Johnson Controls®
employees should refer to the Computer Price List available on the Johnson Controls Portal intranet site by Information
Technology - Acquisition Services (ITAS). Otherwise, please contact your Johnson Controls representative if you
need assistance.
Metasys® CCT Bluetooth® Technology Communication Commissioning Guide
2
Bluetooth Quick Start Guide
This quick start guide leads you through the Bluetooth device setup for Windows 7. Your steps may vary depending
on the vendor of the Bluetooth wireless device and your operating system.
You must repeat steps 1–12 for each Bluetooth converter you set up, because each device is assigned its own COM
port.
Note: The BTCVT Wireless Commissioning Converter used during this procedure should be the one that you intend
to use when uploading and downloading controllers. This procedure allows your computer to pair with the
Wireless Commissioning Converter. You can pair with more than one Wireless Commissioning Converter,
but you can only connect to one converter at a time.
Locate your BTCVT Wireless Commissioning Converter.
Plug your BTCVT Wireless Commissioning Converter into the SA BUS port or the FC BUS port on
your field controller.
Metasys® CCT Bluetooth® Technology Communication Commissioning Guide
3
On the BTCVT, verify that the Power LED is green, and that the Fault LED is off.
Verify that your computer's wireless is turned on. Typically, the internal wireless on/off button is on
the side of the laptop or above the keyboard.
Note:
Usually, a wireless button or icon lights up when the internal wireless is on. The following
images are examples of typical wireless icons.
Right-click the Bluetooth icon ( ) in your system tray, and then select Add a Device from the
pop-up menu. The Add a device wizard appears, and Windows searches for devices within range.
Note:
If you do not see the icon in the system tray, click the Show hidden icons arrow in the tray,
click Customize, and then set the Bluetooth item to Show icons and notifications. Click
OK to close the window. The Bluetooth icon is added to your system tray.
Metasys® CCT Bluetooth® Technology Communication Commissioning Guide
4
Select your Bluetooth device and click Next. The Add a device wizard starts.
Note:
Your device's 12 digit MAC address is printed on the case of the device. To identify your
device in the Add a Device wizard, match the address on your BTCVT hardware to the
address listed in the wizard.
When you are prompted to enter the pairing code for the device, enter BTCVT. Click Next.
Metasys® CCT Bluetooth® Technology Communication Commissioning Guide
5
A confirmation screen appears and says that the device was successfully added to the computer.
Click Close.
Note your device's COM port number. To do this, click the Windows start button, select Control
Panel > Devices and Printers, right-click the device, and then click Properties. Select the Hardware
tab to find the COM port number.
Note:
Your COM port may be different from this example.
Metasys® CCT Bluetooth® Technology Communication Commissioning Guide
6
Launch the CCT, and select Load to test the Bluetooth device connection. The Load Device wizard
appears.
Metasys® CCT Bluetooth® Technology Communication Commissioning Guide
7
Select Bluetooth for the connection type, and enter the Bluetooth COM port number that you
discovered in step 9 in the Bluetooth COM Port field.
Note:
No other parameters are needed to test the Bluetooth device connection.
Note:
The CCT remembers the most recent COM port entry for future uses.
Click Next. The wizard displays the text Connecting, and then changes to Connected.
Note:
When Connected appears, the blue LED on the BTCVT device turns on and remains solid
(not flashing), indicating a successful connection to the CCT.
Note:
The SA/FC LED on the BTCVT turns on and flashes, indicating that communications to the
Field controller are established.
Metasys® CCT Bluetooth® Technology Communication Commissioning Guide
8
Troubleshooting
Table 1: Troubleshooting
Problem
You cannot communicate with the Wireless
Commissioning Converter from the CCT.
You receive a Connection failed! alert.
Solution
Use the following procedure to verify the computer's wireless state, verify the
COM port, and test the connection between your computer and wireless
device.
1. Locate the wireless icon on your laptop keyboard. If the wireless light is
off, press the laptop’s wireless button to turn it on.
2. Locate the Bluetooth icon ( ) in your system tray. Click Show hidden
icons to make all icons visible. If your Bluetooth icon is red ( ), right-click
the icon and select Turn Adapter On. If you do not see a Bluetooth icon,
work with your IT support to order and install the correct Bluetooth wireless
module and drivers.
3. Verify the COM port. In Devices and Printers, right-click the device, and
then click Properties. Select the Hardware tab to find the COM port
number.
4. Test the connection and signal quality between your computer and the
Wireless Commissioning Converter. See Verifying the Connection between
the Laptop and the Wireless Commissioning Converter.
The computer does not communicate properly If you plug in the Bluetooth wireless adapter before the installation software
with the Bluetooth wireless USB adapter.
prompts you to do so, the computer may install its own drivers and may not
communicate properly with the Bluetooth wireless USB adapter. If this occurs,
use the following recovery procedure:
1. Unplug the Bluetooth wireless USB adapter.
2. On the Start menu, click Run, and then type %windir%\inf.
3. Rename the BTH.inf file to BTH.bak.
4. Uninstall the Bluetooth software by using the Add/Remove Programs
feature in Control Panel.
5. Restart the computer.
6. Reinstall the Bluetooth wireless USB adapter. See Installing the Bluetooth
Wireless USB Adapter.
On a computer already configured to use the
USB Bluetooth adapter, the Found New
Hardware Wizard appears when you plug the
USB Bluetooth adapter into the USB port.
The Found New Hardware Wizard appears if you unplug an already configured
USB Bluetooth wireless adapter from your computer and then plug it into a
different USB port on the same computer (for example, if you move the adapter
from your laptop to your docking station).
When the Found New Hardware Wizard appears:
1. Click Install the software automatically (Recommended), and click
Next. The wizard reconfigures the computer to use the adapter on the
new USB port.
2. Click Finish.
Metasys® CCT Bluetooth® Technology Communication Commissioning Guide
9
Table 1: Troubleshooting
Problem
Solution
When you try to connect to the BTCVT device The Bluetooth driver for the laptop is not fully compatible with the BTCVT
with your laptop, this error message appears: device. Contact your network help desk for assistance or go to the
manufacturer’s website to download a compatible driver. Remove the old
The COM1 connection failed. Could not
drivers before you install the new drivers.
connect to remote device.
You are unable to pair or maintain pairing with
your BTCVT device.
A paired Wireless Commissioning Converter The Wireless Commissioning Converter holds 20 paired device addresses in
prompts you for the passcode.
internal memory. At this time, there is no way to clear the paired device
addresses, and there is no workaround. However, once you enter the
passcode, as prompted, the laptop computer communicates with the Wireless
Commissioning Converter. To prevent this problem, limit the number of laptops
that pair with any single converter.
Metasys® CCT Bluetooth® Technology Communication Commissioning Guide
10
Detailed Procedures
Verifying the Connection between the Laptop and the Wireless Commissioning
Converter
To test the connection and see the signal quality between your laptop and the Wireless Commissioning Converter
before using CCT to upload or download a controller, follow these steps:
1. Click the Windows start button, and then click All Programs > Johnson Controls > Metasys > Bluetooth
Wireless Utility.
2. On the Configuration tab, enter the COM port number assigned to your Bluetooth device, and then click Connect.
When the connection is made, Connected appears in the lower-left corner of the BTCVT Wireless Utility window.
Note: To find your COM port number, click the Windows start button and select Control Panel > Devices and
Printers, right-click the device, then click Properties. Click the Hardware tab to find the COM port number.
Note: Each device is assigned a different COM port.
Note: If the Wireless Commissioning Converter determines that no valid Metasys application is using the
connection after 60 seconds, the Converter ends the connection.
Metasys® CCT Bluetooth® Technology Communication Commissioning Guide
11
3. Click the Status tab to view the signal quality. Note your Wireless Link color and status, then compare your
results to Table 2.
Table 2: Wireless Link Status
1
Color (Percent)
Status
Green
Good
Description and Corrective Action
Wireless link is good and optimal for use with CCT. No corrective action
required.
Note:
Yellow
Fair
Wireless link is fair and sufficient for use with CCT. No corrective action
required.
Note:
Red
Poor
1
Disconnected
To improve your Wireless Link status, keep your computer as close
to the Wireless Commissioning Converter as possible.
Wireless link is poor and insufficient for use with Wireless Commissioning
Converter. Try moving the laptop closer to the Wireless Commissioning
Converter or look for sources of interference.
Note:
No Bar
To maintain a strong Wireless Link status, keep your computer as
close to the Wireless Commissioning Converter as possible.
Poor Wireless Link status indicates that the distance between your
computer and the Wireless Commissioning Converter is too great or
that outside wireless interference is too great.
Wireless link is not established or the connection is broken. Verify settings
and try to connect to the Wireless Commissioning Converter again.
The Wireless Link Status is a measure of the signal strength and does not relate to the transmission speed of wireless
communication.
Note: To maintain good Wireless Link status, keep your computer as close to the Wireless Commissioning
Converter as possible.
4. Close the BTCVT Wireless Utility before you use the CCT to upload or download a controller. We do not
recommend using the BTCVT Wireless Utility while uploading or downloading.
Metasys® CCT Bluetooth® Technology Communication Commissioning Guide
12
Installing the Bluetooth Wireless USB Adapter
Note: We recommend that you do not install an external Bluetooth wireless adapter if Bluetooth is built in to your
computer. See Bluetooth Quick Start Guide if Bluetooth is built in.
Note: The instructions to install the USB adapter may vary depending on the vendor of the USB Adapter. Before
installing the USB adapter, familiarize yourself with the vendor’s installation instructions.
Important: Do not plug in the USB adapter until prompted to do so. If you plug in the USB adapter before prompted,
see the Troubleshooting section.
1.
2.
3.
4.
Close all programs and insert the USB adapter installation media. The installation program appears.
Note: If the installation does not start automatically, on the Start menu, click Run. In the field that appears,
enter the vendor setup program, for example D:\setup.exe (where D is the letter of your CD-ROM or
DVD drive).
Click Install Bluetooth Driver. The installation begins and the welcome screen appears.
Click Next. The License Agreement screen appears.
To accept the terms of the license agreement, click I accept the terms in the license agreement and click
Next. The Destination Folder screen appears.
5.
6.
Click Next. The Ready to Install the Program screen appears.
Click Install. The program installs.
7.
Note: During the installation process, you may see a Driver Signature Notice dialog box saying no certification
program is in place for Bluetooth devices. If this appears, click OK.
When the Bluetooth device not found dialog box appears, click Cancel.
Note: You may also be prompted to plug in your USB hardware, which starts the Found New Hardware Wizard.
Wait until the Windows Found New Hardware Wizard is complete before clicking OK. If you are not
prompted to plug in the USB hardware, wait until the driver installation is complete before you plug in
the USB hardware.
8.
9.
Note: Depending on the adapter you install, you may be prompted to enter a security code. If so, click No and
follow the directions on the screen to enter the code manually. The code is labeled SK and is printed on
the back of the Bluetooth wireless adapter.
After the software has been successfully installed, click Finish to close the final window. A red Bluetooth icon
appears on the system tray.
Plug in the USB adapter. The Found New Hardware Wizard appears.
Note: Your computer may install the driver automatically without the Found New Hardware Wizard. If it does,
restart the computer (if prompted) and go to Bluetooth Quick Start Guide.
10. Click Install from a list or a specific location and click Next. The Please choose your search and installation
options screen appears.
11. Click Search for the best driver in these locations and click Next. The Completing the New Found Hardware
Wizard screen appears.
12. Click Finish, and look for the white Bluetooth icon on the system tray. (
).
13. Ensure that your Bluetooth device is connected to your computer (plug it in if not already prompted) and restart
your computer.
14. After restarting your computer, wait until you see the blue and white Bluetooth icon (
) on your system tray.
15. See Bluetooth Quick Start Guide to set up your device.
Metasys® CCT Bluetooth® Technology Communication Commissioning Guide
13
Related Documentation
Table 3 provides a list of documents related to the CCT and the Wireless Commissioning Converter.
Table 3: CCT and Wireless Commissioning Converter Documentation
For Information On
See Document
LIT or Part Number
Installing the CCT Software
CCT Installation Instructions
LIT-12011529
Connecting the Wireless Commissioning
Converter to Hardware; Wireless
Commissioning Converter Specifications
Wireless Commissioning Converter Installation Part No. 24-10108-2
Instructions
Using or Configuring Controller Applications Controller Tool Help
in the CCT
1
1
LIT-12011147
This LIT number represents a printer-friendly version of the Help.
Building Efficiency
507 E. Michigan Street, Milwaukee, WI 53202
Metasys® and Johnson Controls® are registered trademarks of Johnson Controls, Inc.
All other marks herein are the marks of their respective owners.© 2014 Johnson Controls, Inc.
Published in U.S.A.
Metasys® CCT Bluetooth® Technology Communication Commissioning Guide
www.johnsoncontrols.com
14
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising