SMG1002-2S VOIP Gateway Installation Manual VER 1.5

SMG1002-2S VOIP Gateway Installation Manual VER 1.5
SMG1002-2S VOIP Gateway
Installation Manual
VER 1.5
Sywnay Information Engineering Co.,Ltd
www.synway.net
CONTENT
1.Appearance Description ................................................................................................................. 2
1.1 Front Panel ....................................................................................................................... 2
1.2 Rear Panel ........................................................................................................................ 2
2.Hardware Connection .................................................................................................................... 3
3.Basic WEB Settings .......................................................................................................................3
3.1 Network Setting ................................................................................................................. 4
3.2 Protocol And Number Setting ............................................................................................. 5
3.2.1 SIP Protocol And Number Setting ....................................................................................... 5
3.2.2 MGCP Protocol And Number Setting.................................................................................... 6
3.3 Call Route Setting .............................................................................................................. 6
4.Operation Test ............................................................................................................................. 7
SMG1002-2S VOIP Gateway (SIP) Installation Manual VER 1.0
Appearance Description
1.1 Front Panel
Image 1-1 Front Panel
Indicator
Power
Active
Port 1-2
Description
Power indicator, turn the lights connected to the power supply for the long
bright state.
Status indicators, the normal operation of the lamp is flashing
Port work light, off-hook, ringing, the lights are flashing during a call, the standby is
off.
Table 1-1 Front panel connectors and LEDs
1.2 Rear Panel
Image 2-2 Rear Panel
The rear
panel
Description
connectors
and LEDs
DC 12V
Power cord interface, connect the power cord.
Equipment upstream interface, when in the 10M Ethernet port rate, the green light, orange light
WAN
off; When working in the 100M Ethernet port speed, green and orange lights are on, when the
flow of data out of date, the green light, orange lights flashing.
2
SMG1002-2S VOIP Gateway (SIP) Installation Manual VER 1.0
Device configuration interface, when in the 10M Ethernet port rate, the green light, orange light
LAN
off; When working in the 100M Ethernet port speed, green and orange lights are on, when the
flow of data out of date, the green light, orange lights flashing.
1-2
FXS connected to a telephone or PBX trunk interfaces.
Table 1-2 Rear panel connectors and LEDs
Hardware Connection
Firstly, using the power supplied in the package box to connect SMG1002-2S to power on it. And WAN port
SMG1002-2S Series integrated access devices connected to the hub or switch, as shown in Figure 2-1.Making
SMG1002-2S to connect with the service network, and then connecting the PC to the LAN port of SMG1002-2S,
making data configuration for SMG1002-2S and Port1-2 connected to the phone.
Figure 2-1 SMG1002-2S Series Integrated Access Device as a proxy server connection
Basic WEB Settings
Entering the Web interface to configure the SMG1002-2S . The default of LAN port address is 192.168.11.1.
3
SMG1002-2S VOIP Gateway (SIP) Installation Manual VER 1.0
Set the IP address of PC which is connected with LAN port to the same network segment. And then, open the IE
browser, enter the LAN port IP in the address bar to login the WEB network management device for business
configuration. WEB default user name and password are: admin.
Figure2-6 WEB Login Interface
3.1 Network Setting
The WAN port of SMG1002-2S supports 3 different operating modes which are DHCP, PPPoE, and Static. Users
can set “the WAN configuration” in the Web, such as IP address, mask, IP address, DSN and so on. Make
SMG1002-2S accessing to business network normally.
4
SMG1002-2S VOIP Gateway (SIP) Installation Manual VER 1.0
Figure3-2 WAN Setting Interface
3.2 Protocol And Number Setting
SMG1002-2S supports both SIP and MGCP protocols. Before the configuration of protocol and number,
SMG1002-2S needs to determine the type of VOIP protocol that the softswitch communicates with SMG1002-2S
and obtain information such as softswitch address and account number.
Usually, SMG1002-2S will not support the different VOIP protocols at same time, so when setting the protocol
and number, users only need to set the parameters consistent with the softswitch’s protocol. The following two
VOIP protocol are supported by SMG1002-2S, registration of the specific configuration of the softswitch
instructions depend on the actual situation to configure:
3.2.1 SIP Protocol And Number Setting
Fill sip server's domain, under normal circumstances, and fill the same SIP server IP address for the domain;
butt IMS, IMS platform to fill in the domain name.
When registering softswitch with SIP protocol, Users should set the “active server” and “domain” as softswitch
IP addresses in“SIP configuration” in WEB, and set the “active server port” as same as “softswitch registered
Port” .This equipment SIP signaling port, the default value is 5060.
Click Sip Settings to modify in the interface below
Figure3-3 SIP Setting Interface
After the above settings, in the "Number Configuration" -> "Number Batch Edit", assign a number to the service
port of the device, set the uplink protocol of the port to "SIP", set the "Phone number ”and “Authentication
Name" as assigned user account name of softswitch, "registered password" set to the corresponding user
5
SMG1002-2S VOIP Gateway (SIP) Installation Manual VER 1.0
account password, and open the port registration.
3.2.2
MGCP Protocol And Number Setting
Setting the “MGCP address ” as “softswitch’s IP address”, and “MGCP port ” should be set as same as “MGCP
protocol port”,When SMG1002-2S registers softswitch with MGCP protocol, the default port of MGCP protocol is
2727.The Local Domain Name is set to the device domain name specified by the Softswitch, and the End Node
Prefix is set to the softswitch prefix of the endpoint name assigned to the device.
For example, the softswitch assigns 32 user nodes to the device "weych". The node ID of each user is "aaln /
01-aaln / 2". The MGCP configuration of the SMG1002-2S is shown in the following figure. The local domain
name is set to "weych" The node prefix sets "aaln /" with the same 32 user nodes.
After making the above settings, assign the number to the device port in the "Number Configuration" ->
"Number Batch Edit", set the port upstream protocol to "MGCP", and set the phone number to the suffix of the
name specified by the softswitch Section, while opening port registration. For example, the softswitch assigns
32 user nodes to the device "weych". The node ID of each user is "aaln / 01-aaln / 2". Set the telephone number
of the port as 01,02 as shown in the figure below.
3.3 Call Route Setting
When using the SIP protocol, SMG1002-2S supports adding different call rules to define the number conversion
and routing IP in routing table. In WEB setting interface, Select” Call Path”, users can see a default
“DigitMap-Default”, besides this default Call Path, user can manually add his own. When the call path is set,
users can go to “Port Settings””Basic Settings” to choose the one to activate, as shown below:
Figure3-7 Call Path Setting Interface
By Clicking “Edit”, User can check the detailed rules, call rules are consisted by “0-9, .,*,#,X”(represents
number 0-9,)and []” For example, [1,3,4-6,9]=13,4,5,6,9.
When Routing IP is 0.0.0.0, then the call will be sent to the server address edited in “SIP Settings; If the routing
IP is a specified IP then the calls will be forwarded accordingly(p2p), as below.
6
SMG1002-2S VOIP Gateway (SIP) Installation Manual VER 1.0
Figure3-8 Edit call path interface
Operation Test
After the completion of configuring the operational data, reboot the device and log in to the WEB configuration
interface. And then check the registration status of each port in “Number Configuration”, the status of the port
is "registered" as soon as the registration succeeds. And connect The SMG1002-2S Port1-2 to telephone for dial
test, test SMG1002-2S the caller and the called and other business conditions.
Figure 3-11 phone number setting interface
Synway Information Engineering Co., Ltd.
HQ Add: Synway R&D Building,NO.3756,Nanhuan Rd.Hangzhou,P.R.China
Tel: +86 571 88861158 Fax: +86 571 88850923 Email: marketing@synway.cn
7
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising