denver ipc-1020 denver ipc-1030

denver ipc-1020 denver ipc-1030
DENVER IPC-1020
DENVER IPC-1030
Packing list:
IP camera
Mounting bracket
Antenna
Power Adaptor
CD
Lan cable
Installation guide
Screws
Note: Some models don’t have a separate antenna.
Installation procedure:
Start
Connect the Hardware
Install the Search Tool
Login the IP Camera into LAN
Wireless Settings
Login the IP Camera to the PC
Client
Access by Mobile
End
Note: For the first time use of IP Camera, please refer to the procedures above.
IP Camera
Internet
PC
Router
LAN
WAN
Internet Cable
Power
IP Camera
Internet
PC
Router
WAN
LAN
Internet Cable
Power
Connect the camera with Internet cable to the router, and with the power cord to the mains,
like shown above.
1. Installation of the Search Tool
Next
Insert the CD and install the following software:
1. Open the File “IPC-1020 & IPC-1030”, click on “OCX setup” — “Next” — “Install” —
“Finish”
2. Open the File “Search Tool”, Copy the “Search Tool” to the desktop and launch it.
2. Login of the IP Camera into the LAN
After the hardware is connected properly, launch the search tool, and the IP address of the
camera will be displayed automatically.
Note: If the Search Tool issues the message "Subnet mask does not match, please click
Double click the camera IP address in the search tool.
In your default browser a login screen like shown below will be displayed:
Note: Both the username and password are “admin”
(Please change the account user name and password for safety later)
After entering the correct user name and password, the Login screen will be displayed.
(It supports 6 visitors watching online at the same time)
Note: If the OCX already has been installed you may login directly. If not, please install
OCX.
A. Click on “OCX” to download and Install it.
B. Refresh the webpage and login again, the camera video will be displayed as below
Live video
3. Wireless Setting
1. Click on the
button to access the “Wireless” settings.
2. Search for the WIFI signals and choose the desired SSID.
3. Make sure that all parameters are the same like in your router, enter the WIFI network
key.
4. After 30 seconds click on “Check”, the notification will show you if the WIFI settings are
successful.
5. If correct, just go back to select “Apply”, then disconnect the network cable.
Note: If the camera IP Address can not be found by the search tool, please connect the
internet cable again to check the WIFI settings.
Checking the WIFI signal connection status
4. Device information Setting
1) Click on the
icon to access the “ Device information” settings
2) You will see all information for the IP camera
5. Time Settings
1) Click on the
icon to access the “Time” settings
2) You may choose any NTP server, then click on “Apply”
3) Choose the desired time and click on “Apply” to activate it
6. Record settings
1) Click on the
icon to access the “Record” settings
2) Choose “on”
3) Choose between ”First stream” or ”Second stream”
4) Choose the time schedule for recording
5) Click on “Apply”
7. Alarm Settings & Motion Detection
Configuration
1) First, you should activate the “Motion detection” and choose the display detail that
should be monitored (you may alter the detail as require).
2) You may choose the “Alarm trigger ringtone” and time schedule, then click on ”Apply”,
If the motion detect detects a motion in the configured display detail the alarm bell will
ring (The model without audio function is not provided with this alarm ring tone
notification)
8. Alarm Notification Setting & Email, FTP
1) The email configuration screen serves for the preparation of the alarm function. If the
motion detect activates your camera is triggered, you will receive an email containing
photos. Precondition for this is the correct setup and test of the service. Here the
configuration of a Gmail account as example:
Note: This function only works if the IP camera is connected to the network. If you use Gmail,
you must configure the port as 465, SSL as TLS. But the most important is, that you check if
your email client has SMTP enabled.
2) FTP service is a precondition for the alarm function. If the motion detect activates your
camera an email with photos will be submitted to you. For this it is required that you
configure the email service correctly in check it for functionality. For example:
3) Alarm Service Settings, please enter the same settings like in the screenshot below:
9. System log & Net work setting
1). System log is intended for administrators to monitor the system operation
2). In "Network Settings" you may modify the IP address, gateway and port number
10. DDNS Setting
1)
Click on the
icon and the choose “DDNS Service Settings”.
2)
3)
Choose the DDNS server, enter the DDNS user name and password.
Submit, refresh, then the DDNS status will be shown as “DDNS Succeed”.
11. PTZ Setting & User Setting
1). Here you may configure some PTZ options
2). Modification of the user password
12. Multiple Settings
1) Refresh the device in the LAN search, then you will find other cameras connected to the
2)
3)
4)
5)
same LAN
Click on the “2nd device”
Click on the desired the camera to add it as the 2nd device , enter the correct user name and
password
Click on “Apply”
You may add up to 9 cameras to the multiple settings
13. Maintainance & ONVIF
1) With this option you may restore the camera to its factory settings, and perform
firmware updates.
2) ONVIF Support
14. Auto Snap & Video Mark
1) Capturing of images to the SD card and FTP upload
2) Select the screen detail (you can change the size of the window), click on "Apply" and an
obscured screen area appears
15. Image setting
1) Click on apply to modify the brightness, saturation, sharpness, exposure, contrast
2) Click on the application to modify the exposure mode, infrared lamp,
3) Click on applications to change the value of the IR-cut
4) If you click on “Default” all image settings will restored to the default value
FAQ:
A. Password forgotten
1) Reset your camera.
While the power is on, you must press the RESET button for 10
seconds. The button you will find at the bottom of the camera. With outdoor cameras
the white reset button is located at the end of the power cord.
2) After the reset is completed, the camera is reset to the factory settings, then the
username and the password is "admin".
B. No video, only a black screen, is displayed in the browser
Note: If there is still no live video after running OCX ActiveX, please try to enable the
ActiveX options in the IE security settings by performing the following steps:
1. Deactivate the firewall of your computer.
2. Change the ActiveX settings in “IE” browser > “Tool” > “Internet Options” > “Security” >
“Custom Level” > “ActiveX control and Plug-ins”, all ActiveX options should be
configured as “Enable”:
Especially:
Enable: Download unsigned ActiveX controls
Enable: Initialize and script ActiveX controls not marked as safe
Enable: Run ActiveX controls and plug-ins
a.
b.
ALL RIGHTS RESERVED, COPYRIGHT DENVER ELECTRONICS A/S
Electric and electronic equipment and included batteries contains materials, components
and substances that can be hazardous to your health and the environment, if the waste
material (discarded electric and electronic equipment and batteries) is not handled
correctly.
Electric and electronic equipment and batteries is marked with the crossed out trash can
symbol, seen below. This symbol signifies that electric and electronic equipment and
batteries should not be disposed of with other household waste, but should be disposed of
separately.
As the end user it is important that you submit your used batteries to the approriate and
designated facility. In this manner you make sure that the batteries are recycled in
accordance with legislature and will not harm the environment.
All cities have established collection points, where electric and electronic equipment and
batteries can either be submitted free of charge at recycling stations and other collection
sites, or be collected from the households. Additional information is available at the
technical department of your city.
Imported by:
DENVER ELECTRONICS A/S
Stavneagervej 22
DK-8250 Egaa
Denmark
www.facebook.com/denverelectronics
Hereby, Inter Sales A/S, declares that this tablet DENVER (DENVER IPC-1020 + DENVER
IPC-1030) is in compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC.
A copy of the Declaration of Conformity may be obtained at
Inter Sales A/S
Stavneagervej 22
DK-8250 Egaa
Denmark
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising