Cube EVID S44 - AV-iQ
EVID Compact Sound Speaker System
EVID-S44, EVID-S44W, EVID-2.1, EVID-2.1W, EVID-40S, and EVID-40SW
en | Installation Manual
en
3
Table of contents
1
Safety
4
2
Welcome
5
2.1
System features
5
3
System overview
6
3.1
Packing lists
6
3.2
Product information
8
3.3
Dimensions
9
4
Installation
10
4.1
Surface mount satellite speaker installation
10
4.2
Wall bracket range of motion
11
4.3
Surface mount subwoofer installation
11
4.4
Removing subwoofer from the wall
13
5
Wiring
14
5.1
Wattage tap
14
5.2
70v/100v/4 ohm Mono
15
5.3
8 ohm Stereo
16
6
Troubleshooting
17
7
Technical data
18
7.1
Frequency response
18
Electro-Voice
Installation Manual
2015.02 | 03 | F.01U.310.295
EVID Compact Sound Speaker System
1
Safety
Warning!
Suspending any object is potentially dangerous and should only be attempted by individuals
who have a thorough knowledge of the techniques and regulations of suspending objects
overhead. Electro-Voice strongly recommends all loudspeakers be suspended taking into
account all current national, federal, state, and local laws and regulations. It is the
!
responsibility of the installer to ensure all loudspeakers are safely installed in accordance
with all such requirements. When loudspeakers are suspended, Electro-Voice strongly
recommends the system be inspected at least once per year or as laws and regulations
require. If any sign of weakness or damage is detected, remedial action should be taken
immediately. The user is responsible for making sure the wall, ceiling, or structure is capable
of supporting all objects suspended overhead. Any hardware used to suspend a loudspeaker
not associated with Electro-Voice is the responsibility of others.
Safety Agency Compliance
The EVID 2.1 and EVID 40S bracket systems have successfully passed EIA-636 at a safety
factor of 8:1. The bracket systems are intended to support only the EVID 2.1 and EVID 40S
respectively. Do not use either bracket system for any other purpose. Never set anything on or
hang anything from the EVID 2.1 or EVID 40S enclosures when using the brackets.
As an added safety measure, it is suggested the user install an extra suspension point back to
the building structural supports. This redundant safety point should have as little slack as
possible (less than one (1) inch is preferable).
Figure 1.1: Surface mount satellite speaker (left) and surface mount subwoofer (right) with safety cable
2015.02 | 03 | F.01U.310.295
Installation Manual
Electro-Voice
en
2
5
Welcome
Thank you for purchasing the EVID Compact Sound Speaker System. Read through this manual
to familiarize yourself with the features, applications, and precautions before you use these
products.
The EVID Compact Sound Speaker System is a very compact full-range loudspeaker ideal for
applications requiring high-quality sound. Its shape flexibility and size make it nearly invisible
for use in background/foreground music systems for restaurants, bars, patios, retail, and other
applications. The system consists of a high performance surface mount 8-inch subwoofer
module with a crossover network to support the included four (4) surface mount 2-inch
satellite speakers. The system provides for easy signal connections at the subwoofer and can
support either 4/8 ohm or 70/100v signal connections. Its high power handling allows the
system to be used in a wide variety of environments and spaces to provide high quality
background or foreground music.
2.1
System features
▪
A complete matched background/foreground music speaker solution.
▪
High power handling – system supports up to 200 watts with 8 ohm and 100 watts with
70v/100v input connections.
▪
Large 8-inch woofer for increased low frequency output.
▪
Direct connection of satellites to subwoofer — simplifies installation wiring.
▪
Convenient detachable phoenix style signal connections speed up installation time.
▪
Large high quality rigid wood subwoofer cabinet supports extended bass response.
▪
Mounting system for surface mount satellites provides secure mounting but allows for
wide-range of motion to adapt to any placement.
Electro-Voice
▪
Easily detachable wall bracket for wall mounting of subwoofer is included.
▪
Attractive subwoofer design with full face grille.
Installation Manual
2015.02 | 03 | F.01U.310.295
EVID Compact Sound Speaker System
3
System overview
3.1
Packing lists
The EVID Compact Sound Speaker System contains four (4) satellite speakers and one (1)
subwoofer. When you open the box for the full system you will find three (3) main boxes
inside; two (2) boxes for the satellite speakers and one (1) box for the subwoofer.
The major components included in one (1) box for the EVID 2.1 surface mount satellite
speaker.
Item
Qty
Description
A
2
EVID 2.1 surface mount satellite speakers
B
2
Wall brackets
C
2
Speaker brackets
D
1
EVID S44 Engineering Data Sheet
E
2
M6 hex drive pan-head screws
F
4
M5 pan-head screws
G
2
Screw sockets
H
1
Hex wrench
Table 3.1: Surface Mount Satellite Speaker (1 box)
2015.02 | 03 | F.01U.310.295
Installation Manual
Electro-Voice
en
7
The major components included in the box for the EVID 40S surface mount subwoofer:
Item
Qty
Description
A
1
Surface Mount Subwoofer
B
1
Wall bracket, assembled in box
C
1
EVID Compact Sound Speaker System manual
D
4
M6 hex drive pan-head screw
E
4
Rubber feet
F
1
Hex wrench
Table 3.2: Surface Mount Subwoofer
Electro-Voice
Installation Manual
2015.02 | 03 | F.01U.310.295
EVID Compact Sound Speaker System
3.2
Product information
Figure 3.1: EVID 2.1 Product Information
Figure 3.2: EVID 40C Product Information
2015.02 | 03 | F.01U.310.295
Installation Manual
Electro-Voice
en
3.3
9
Dimensions
Figure 3.3: Dimensions EVID 2.1 and mounting bracket
Figure 3.4: Dimensions EVID 40S and mounting bracket
Notice!
The mounting bracket dimension drawings are not to scale. Drawing sizes increased for
readability.
Electro-Voice
Installation Manual
2015.02 | 03 | F.01U.310.295
EVID Compact Sound Speaker System
4
Installation
4.1
Surface mount satellite speaker installation
For safety, ensure the mounting surface supports more than the weight of the speaker. Use
only industry-accepted fasteners and mounting methods when mounting the wall bracket.
Consult an expert if you are unsure.
To install the surface mount satellite speaker, do the following:
1.
Using a Phillips head screwdriver (not supplied), tighten two (2) M5 pan-head screws
(not supplied) to attach the wall bracket to a secure mounting surface.
2.
Using a Philips screwdriver, tighten two (2) M5 pan-head screws (supplied) to attach the
speaker bracket to the rear of the cabinet.
3.
4.
Place the speaker bracket onto the wall bracket.
Using the hex wrench (supplied), tighten the M6 hex drive pan-head screw to secure the
speaker bracket to the wall bracket.
For more information, see Safety, page 4.
2015.02 | 03 | F.01U.310.295
Installation Manual
Electro-Voice
en
4.2
11
Wall bracket range of motion
The speaker can be adjusted from side to side or up and down.
Figure 4.1: Horizontal range is 160° and the vertical range is 60°.
4.3
Surface mount subwoofer installation
For safety, ensure the mounting surface supports more than the weight of the speaker. Use
only industry-accepted fasteners and mounting methods when mounting the wall bracket.
Consult an expert if you are unsure.
Caution!
!
Only mount the wall bracket in the vertical V-shape position.
Do not mount the V-bracket or wall bracket side ways or upside down.
Figure 4.2: Wall bracket correct and incorrect mounting positions
Electro-Voice
Installation Manual
2015.02 | 03 | F.01U.310.295
EVID Compact Sound Speaker System
To install the surface mount subwoofer, do the following:
1.
Using a Phillips head screwdriver (not supplied), tighten six (6) M5 pan-head screws
(not supplied) to attach the wall bracket to a secure mounting surface.
2.
Using the hex wrench (supplied), tighten the three (3) M6 hex drive pan head screws to
attach the V-bracket.
3.
Slide the V-bracket into the wall bracket.
The locking detents engage.
For more information, see Safety, page 4.
2015.02 | 03 | F.01U.310.295
Installation Manual
Electro-Voice
en
4.4
13
Removing subwoofer from the wall
To remove the subwoofer from the wall, do the following:
1.
2.
Pull the subwoofer slightly out from the wall.
Lift the subwoofer up.
The locking detents disengage.
Electro-Voice
Installation Manual
2015.02 | 03 | F.01U.310.295
EVID Compact Sound Speaker System
5
Wiring
5.1
Wattage tap
Prior to wiring your system, select the mode of operation (100V/70V/4 ohm or 8 ohm stereo)
by setting the slider switch to the appropriate setting. Select taps using the rotary switch on
the subwoofer input panel. The power taps are 100 W, 50 W, 25 W, and 12.5 W at 70.7V and
100V, as well as a 4 ohm transformer bypass setting. A guide on the input panel shows which
switch positions to use for the power settings at 70V and 100V.
Figure 5.1: Wattage tap
2015.02 | 03 | F.01U.310.295
Installation Manual
Electro-Voice
en
5.2
15
70v/100v/4 ohm Mono
The amplifier and EVID Compact Sound Speaker System is wired for MONO mode. It is highly
advisable to support the unit while these connections are being made. Connect all wires to
the speaker at the back terminal plate observing proper polarity of the connections. After all
connections are made test the complete system operation.
Notice!
The system is designed for operation with four (4) satellite speakers. Operation with less
than four (4) satellite speakers is not recommended.
Electro-Voice
Installation Manual
2015.02 | 03 | F.01U.310.295
EVID Compact Sound Speaker System
5.3
8 ohm Stereo
The amplifier and EVID Compact Sound Speaker System is wired for STEREO mode. It is highly
advisable to support the unit while these connections are being made. Connect all wires to
the speaker at the back terminal plate observing proper polarity of the connections After all
connections are made test the complete system operation.
Notice!
The system is designed for operation with four (4) satellite speakers. Operation with less
than four (4) satellite speakers is not recommended.
Notice!
A standard low impedance (4/8 ohm) amplifier source is required when operating the unit in
STEREO mode.
100/70v operation is not supported in STEREO mode.
2015.02 | 03 | F.01U.310.295
Installation Manual
Electro-Voice
en
6
17
Troubleshooting
Problem
Possible Causes
Action
No Sound
Amplifier
Connect a known working test speaker to the amplifier outputs. If
there is no sound, check all electronics are on, the signal routing is
correct, the source is active; the volume is turned up, and so on.
Correct/Repair/Replace as necessary. If there is sound, the problem is
in the wiring.
Wiring
Verify you have connected the correct wire pairs to the amplifier. Play
something at low level through the amplifier (for example, from a CD
player or tuner). Connect the test speaker in parallel with the
malfunctioning line. If the sound has gone or is very weak, the line has
a short in it (possibly a severe scrape, pinch, or staple puncture). If
the sound level is normal the wire is open (possibly a cut wire or
missed connection). Using the test speaker, move down the line and
test each connection/junction until you find the problem and correct
it. Observe proper polarity.
Verify you have the inputs and outputs connected to the correct wires.
If the subwoofer input panel is not correctly wired, there will be little
or no sound. Observe proper polarity.
Poor Low-
Speakers Wired Out- When two (2) speakers are connected out of polarity (out of phase),
Frequency
of-Polarity
Response
the low frequencies will cancel each other acoustically. Carefully
observe the wire markings or tracers on your speaker wires. Verify the
amplifier (+) terminal is connected to the red speaker terminals and
the amplifier (-) terminal is connected to the black speaker terminals.
Improperly Wired
Using a test speaker as described above, verify all amplifier and
Subwoofer Panel
speaker wires are connected to their proper terminals with the correct
polarity. Reversing just one (1) set of amplifier wires can cut out all
bass output from the subwoofer.
Intermittent
Faulty Connection
Check all connections at amplifier and speakers to ensure they are
Output such as,
clean and tight. If the problem persists, it may be in the amplifier or
Crackling or
wiring. See other actions above.
Distortion
Constant Noise
Defective Amplifier
If the noise is present but no program material is playing, the likely
such as Buzzing,
or other Electronic
cause is the signal chain in the electronics. Evaluate each component
Hissing, Humming
Device
as necessary to isolate the problem.
Poor System
Check and correct the system grounding, as required.
Grounding or
Ground Loop
If these suggestions do not solve your problem, contact your nearest Electro-Voice dealer or
Electro-Voice distributor.
Electro-Voice
Installation Manual
2015.02 | 03 | F.01U.310.295
EVID Compact Sound Speaker System
7
Technical data
EVID 2.1
Frequency Response (-10 dB): 180 Hz - 20 kHz1
Power Handling: 30 W2
EVID 40S
42 Hz - 300 Hz1
200 W2
Sensitivity: 84 dB1
88 dB1
Impedance: 16 ohms
Dual 8 ohm / mono 4 ohm
Maximum SPL: 100 dB1
114 db1
Voice Coverage (H x V): 150° x 150°3
Omnidirectional
Music Program Coverage (H x V): 100° x 100°4
Omnidirectional
Transducer: 50 mm (1.97 in)
Bracket Adjustment Range (H x V): 160° x 60°
200 mm (7.87 in)
Fixed
Connectors: Phoenix (2-pin)
Enclosure: ABS (fire rated)
Transformer Taps: NA
Phoenix (2-pin)
Wood (MDF)
100 W, 50 W, 25 W, 12.5 W
Dimensions (H x W x D): 115 mm x 85 mm x 95 mm
400 mm x 400 mm x 230 mm
(4.53 in x 3.35 in x 3.75 in)
(15.75 in x 15.75 in x 9.06 in)
Net Weight: (each) 0.5 kg (1.1 lb)
Shipping Weight:
12.05 kg (26.55 lb)
1 sub and 4 satellites: 18.26 kg (40.25 lb)
Included Accessories: Wall bracket; hex wrench
Wall bracket; hex wrench
1. Half space (wall mounting).
2. Long Term Program Rating, 3 dB greater than continuous noise pink noise rating.
3. Average 1 kHz – 4 kHz.
4. Average 1 kHz – 8 kHz.
7.1
Frequency response
Figure 7.1: EVID-2.1 with EVID-40S frequency response
2015.02 | 03 | F.01U.310.295
Installation Manual
Electro-Voice
en
Electro-Voice
Installation Manual
19
2015.02 | 03 | F.01U.310.295
Bosch Security Systems, Inc
12000 Portland Avenue South
Burnsville MN 55337
USA
www.electrovoice.com
© Bosch Security Systems, Inc, 2015
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising