VCB-9324 - cs.psn

VCB-9324 - cs.psn
L73E4/US GB 1998, 20, 15
INSTRUCTION MANUAL
B/W CCD Camera
About this manual
Before installing and using the camera, please read this manual
carefully. Be sure to keep it handy for later reference.
VCB-9324
L73E4/US GB 1998, 20, 15
INFORMATION TO USER
Safety Guard
THIS SYMBOL INDICATES THAT THERE ARE
IMPORTANT OPERATING AND MAINTENANCE
INSTRUCTIONS IN THE LITERATURE ACCOMPANYING
THIS UNIT.
WARNING:
TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK , DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
For the customers in Canada
This Class B digital apparatus complies with Canadian ICES-003.
Pour la clientèle canadienne
Cet appareil numerique de la Classe B est conforme a la norme
NMB-003 du Canada.
This installation should be made by a qualified service person and
should conform to all local codes.
English
1
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by Sanyo may
void the user’s authority to operate this camera.
L73E4/US GB 1998, 20, 15
CONTENTS
PRECAUTIONS........................................................................................ 3
PARTS NAMES AND FUNCTIONS ......................................................... 4
CONNECTIONS AND INSTALLATION ................................................... 6
SETTINGS AND ADJUSTMENTS ........................................................... 9
TROUBLESHOOTING ............................................................................. 9
SPECIFICATIONS.................................................................................... 10
Accessories
1 Vertical holder plate ................................................................ 1 pc.
1
FEATURES
• Built-in interline transfer method 1/3" CCD, approx. 270,000
picture elements
• Low smear, anti-blooming, low lag, no burning and no geometric
distortion using the CCD solid state image device
• Built-in fixed focal lens, F=2.0, f=3.8 mm
• 100% solid state components giving excellent immunity to shock
and vibration
• Not subject to interference from magnetic or electrostatic fields
• Built-in IR. LED by very required mininum illumination is approx.
0 lux at 4.5 m
• Horizontal resolution, more than 400 TV lines
• Power supply: 24 V AC operation
2 English
L73E4/US GB 1998, 20, 15
PRECAUTIONS
In case of problem
Do not use the camera if smoke or a strange odour comes from the
unit, or if it seems not to function correctly. Disconnect the power
cord immediately, and consult your dealer (or a Sanyo Authorized
Service Centre).
Do not open or modify
Do not open the cabinet, as it may be dangerous and cause damage
to the unit. For internal settings and repairs, consult your dealer (or a
Sanyo Authorized Service Centre).
Do not put objects inside the unit
Make sure that no metal objects or flammable substance get inside
the camera. If used with a foreign object inside, it could cause a fire,
short-circuits or damages.
If water or a liquid gets inside the camera, disconnect the power cord
immediately, and consult your dealer (or a Sanyo Authorized Service
Centre). Be careful to protect the camera from rain, sea water, etc.
Be careful when handling the unit
To prevent damages, do not drop the camera or subject it to strong
shock or vibration.
Install away from electric or magnetic fields
If installed close to a TV, radio transmitter, magnet, electric motor,
transformer, audio speakers the magnetic field they generate will
distort the image.
English
3
Protect from humidity and dust
To prevent damages to the camera, do not install it where there is
greasy smoke or steam, where the dampness may get too high, or
where there is a lot of dust.
Protect from high temperatures
Do not install close to stoves, or other heat generating devices, such
as spotlights, etc., or where it could be subject to direct sunlight, as
that could cause deformation, discoloration or other damages.
Be careful when installing close to the ceiling, in a kitchen or boiler
room, as the temperature may raise to high levels.
Install where the temperature range will stay between –10˚C and
50˚C. (no condensation)
Cleaning
• Dirt can be removed from the cabinet by wiping it with a soft
cloth. To remove stains, wipe with a soft cloth moistened with a
soft detergent solution and wrung dry, then wipe dry with dry soft
cloth.
• Do not use benzine, thinner or other chemical product on the
cabinet, as that may cause deformation and paint peeling. Before
using a chemical cloth, make sure to read all accompanying
instructions. Make sure that no plastic or rubber material comes in
contact with the cabinet for a long period of time, as that may
cause damage or paint peeling.
L73E4/US GB 1998, 20, 15
PARTS NAMES AND FUNCTIONS
8
1 Hood lens
2 Focus ring
9
The focus does not need adjustment for subjects 1 m and more
from the lens. If the subject is closer than 1 m, turn the focus ring
to adjust the focus as necessary. (See page 9.)
8
3 Lens
4 Lens cover
This cover will protect the lens from dust and damage.
5
6
5 24 V AC input terminal
(24 V AC, GND)
7
With this camera use only the 24 V AC
power adaptor model No. VPT-115
available from Sanyo.
1
2
4
Power supply connections
Use a 3 wire grounded cable (22 AWG
or more), and connect as shown by the
illustration.
F
3
GND
AC
AC
CAUTION:
• To prevent camera and/or AC adaptor
failure, pay close attention polarity
when making the connections.
• To prevent fire hazard any UL listed
wire rated VW-1, should be used for
the 24 V AC cable input terminal.
4 English
L73E4/US GB 1998, 20, 15
PARTS NAMES AND FUNCTIONS
6 Camera mounting screw hole (1/4"–20 UNC)
When mounting the camera to the mounting bracket, use this
installation hole.
7 Lens cover fixing screw
8 GND (ground) terminal screw
Loosen the GND terminal screw, insert the coaxial cable into the
clamp and tighten the GND terminal screw.
9 VIDEO OUT terminal screw
Align the centre wire of the coaxial cable with the VIDEO OUT
terminal, then first tighten the cable clamp and then the VIDEO
OUT terminal screw.
• Cable type RG-6U (5C-2V)
The view angle of this camera is as follows:
Horizontal:
71˚
Vertical:
53˚
Diagonal:
90˚
To adjust the camera angle, use the camera
mounting bracket (sold separately).
English
5
F Line phase volume
When using a camera switcher to connect 2 cameras or more to
one monitor, there may be a vertical roll of the images when
switched. In such a case, set as described below.
Switch the display on the monitor from camera 1 to camera 2.
Adjust the LINE PHASE volume on camera 2 until the vertical
roll of the image stops.
If more than two cameras are used, please repeat this procedure
for all the cameras.
CAUTION:
If the vertical roll cannot be corrected by setting the LINE PHASE
volume on camera 2, try setting the LINE PHASE volume on camera
1. If it still cannot be corrected, please check that the polarity of the
power cords of all connected devices is correct.
L73E4/US GB 1998, 20, 15
CONNECTIONS AND INSTALLATION
Connecting the coaxial cable horizontally
1
2
Cut and prepare the extremity of the coaxial cable (sold separately), as illustrated.
Attach the coaxial cable to the base.
Loosen the VIDEO OUT terminal screw (A) and the GND terminal screw (B), then insert the
center wire of the coaxial cable in the VIDEO OUT terminal and make sure the shielding
mesh part of the cable is located into the GND cable clamper, then tighten both screws (A
and B) to attach the cable.
1
1
Connecting the coaxial cable vertically (using the vertical holder
plate)
1 Cut and prepare the extremity of the coaxial cable (sold separately), as illustrated.
2 Loosen the VIDEO OUT terminal screw and remove the GND terminal screw.
3 Insert the coaxial cable into the GND terminal clamp (a), then attach the clamp to
the supplied vertical holder plate (b) using the screw (c) from the second GND
terminal.
(Return the shielding mesh here)
A
B
2
4 Attach the vertical holder plate to the GND terminal using the terminal screw, then
insert the centre wire of the coaxial cable into the VIDEO OUT terminal and tighten
the terminal screw.
c
a
b
6 English
L73E4/US GB 1998, 20, 15
CONNECTIONS AND INSTALLATION
Installing the BNC plug (sold separately)
To connect the camera to peripheral devices, use a coaxial cable with BNC plug.
1
Cut the extremity of the coaxial cable (sold separately), as illustrated.
• Cable type RG-6U (5C-2V), 500 m maximum.
If the type of peripheral devices connected, the type of cable used and/or the cable
length are not as specified, the image and synchronization signals may not be
transmitted correctly.
CAUTION:
Use CCTV/Video grade coaxial cable. Due to its construction, an RG-59U cable will not
transmit the signal properly when installed through conduits or through the air, and
therefore cannot be used.
2
3
Insert the cable through the adaptor, then turn the shielding mesh over.
4
Screw the adaptor onto the plug.
Loosen the center wire securing screw of the plug, then install the cable in the BNC
plug, so that the center wire is threaded through the plug center opening.
Before tightening the center wire securing screw, make sure the center wire comes out
through the plug center opening.
English
7
1
2
7mm 8mm
3
4
L73E4/US GB 1998, 20, 15
CONNECTIONS AND INSTALLATION
Basic connections for monitoring or recording
The peripheral devices (VCR, monitor, etc.) and cables are sold separately.
1
2
(Example of connection to a monitor)
Make the video signal connection between the camera and the monitor or time
lapse VCR.
Plug the AC adaptor to a wall outlet.
Adjust the picture on the monitor using the Brightness and Contrast controls.
Fig. 1
Fig. 2
: VIDEO IN
: VIDEO OUT
(sold separately)
VIDEO IN
Time lapse VCR
(sold separately)
VIDEO OUT
VIDEO IN
CAUTION:
• Make sure the AC adaptor is not
connected to the wall outlet before
connecting it to the 24 V AC input
terminals.
• When making the connections be careful
to respect the polarity and not to
shortcut the terminals.
Monitor
(sold separately)
Multiple cameras connection
You can use multiple cameras by connecting them a camera switcher or a quad unit (sold
separately), then conducting the surveillance from one location by splitting the monitor screen to
view the image from each camera, or by switching the image from each camera on the monitor
screen. For detailed information, please refer to the installed devices instruction manuals.
8 English
L73E4/US GB 1998, 20, 15
SETTINGS AND ADJUSTMENTS
Adjusting the focus
1
2
3
4
Loosen the lens cover fixing screw (A).
Turn the cover counterclockwise to align the tab (C) on the
lens cover with the tab (B) on the base and remove the
cover.
Remove the hood lens (D), then while watching the image
on the monitor turn the focus ring (E) to adjust the focus.
When finished, install the hood lens, then align the tab (C) on
the lens cover with the tab (B) on the base and turn the cover
clockwise until the tab (F) on the cover is aligned with the tab
(B) on the base. Tighten the lens cover fixing screw (A).
E
B
A
D
C
F
C
English
9
TROUBLESHOOTING
Before taking the camera for repairs, please check below to make
sure that the camera is used correctly. If it still does not perform
correctly, please consult your dealer or a Sanyo Authorized Service
Center.
No picture on the monitor screen
• Is the power turned on to all connected devices? Is the voltage
correct?
• Are all the signal connecting cables correctly connected?
• Is the lighting sufficient?
The picture is not clear
• Is the monitor correctly adjusted?
• Is the lens focus correctly adjusted?
• Are the lens surfaces clean?
If there is dust or finger prints on the lens, the image quality will
deteriorate. To clean the lens use a soft cloth or a commercially
available lens cleaning set.
SERVICE:
This camera is a precision instruments and, if treated with care, it
will provide years of satisfactory performance. However, in the
event of a problem, the owner is advised not to attempt to make
repairs or open the cabinet. Servicing should always be referred to
your dealer or Sanyo Authorized Service Center.
L73E4/US GB 1998, 20, 15
SPECIFICATIONS
TV system
EIA standard (525 TV lines, 30
frames/sec.)
Storage environmental
conditions
Temperature: –20˚C ∼ +60˚C
Humidity: less than 70% RH
Scanning system
525 TV lines, 60 field/sec.,
2:1 interlace
Power supply
24 V AC
Power consumption
2.1 W
Image device
Interline transfer method, 1/3 inch
solid state CCD
Weight
Approx. 160 g
537 (H) × 505 (V)
Effective picture elements
510 (H) × 492 (V)
Synchronization system
Line lock
Resolution
400 TV lines horizontally, 350 TV
lines vertically
Video output signal level
1.0 V(p-p)/75Ω (screw-on terminal)
S/N ratio
More than 50 dB
Minimum required
illumination
0 lux
Electronic iris range
1/60 to 1/80,000 sec.
Iris system
Electronic iris
Gain control
Automatic
Lens
Built-in, F2.0, f=3.8 mm, fixed focal
lens, focus adjustment
Angle of view
Horizontally: Approx. 71˚
Vertically: Approx. 53˚
Diagonal: Approx. 90˚
Operational environmental
conditions
Temperature: –10˚C ∼ +50˚C
Humidity: less than 90% RH
DIMENSIONS
51 mm
φ104 mm
Picture elements
Features and specifications are subject to change without prior notice
or obligations.
10 English
L73E4/US GB 1998, 20, 15
SANYO INDUSTRIAL VIDEO
B/W VIDEO CAMERA LIMITED WARRANTY
OBLIGATIONS
In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user’s expense, unless specifically stated otherwise in this warranty. The names and
addresses of Authorized Sanyo Service Centers may be obtained by writing to SFS Corporation, SFC’s warranty administrator, at any of the addresses listed below, or by calling (toll-free) 1-800-421-5013.
New Jersey Office
210 Riser Road
Little Ferry, NJ 07643
201-641-3000
California Office
1200 W. Artesia Blvd.
Compton, CA 90220
310-537-5830
Illinois Office
900 N. Arlington Heights Rd.
Itasca, IL 60143
708-775-1414
THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN THE UNITED STATES OF AMERICA, EXCLUDING HAWAII AND ALL U.S. TERRITORIES AND PROTECTORATES. THIS
WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL USER. THE ORIGINAL DATED BILL OF SALE, SALES SLIP OR RENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE CENTER
AT THE TIME WARRANTY SERVICE IS REQUESTED.
Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO FISHER (USA) CORPORATION warrants this SANYO product against defects in materials and workmanship for the periods specified below. SFC
will repair or replace (at its option) the product and any of its parts which fail to conform to this warranty. The warranty period commences on the date the product was first purchased or rented at retail.
LABOR
3 YEARS
PARTS
3 YEARS
IMAGE DEVICE
5 YEARS
EXCLUSIONS
This warranty does not cover (A) the adjustment of customer-operated controls as explained in the appropriate model’s instruction manual, or (B) the repair of any product whose serial number has been altered, defaced
or removed.
This warranty shall not apply to the cabinet or cosmetic parts, antenna, knobs, batteries or image burns to projection or picture tubes caused by electronic devices or games.
This warranty does not apply to uncrating, setup, installation, removal of the product for repair or reinstallation of the product after repair.
This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including, but not limited to, any malfunction, defect or failure caused by or resulting from unauthorized
service or parts, improper maintenance, operation contrary to furnished instructions, shipping or transit accidents, modification or repair by the user, abuse, misuse, neglect, accident, incorrect power line voltage, fire,
flood or other Acts of God, or normal wear and tear.
The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party to assume for it any other obligation or liability.
THE DURATION OF ANY WARRANTIES WHICH MAY BE IMPLIED BY LAW (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS) IS LIMITED TO THE TERM OF THIS WARRANTY. IN NO EVENT
SHALL SFC BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM OWNERSHIP OR USE OF THIS PRODUCT, OR FOR ANY DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS
UNDER THIS WARRANTY DUE TO CAUSES BEYOND ITS CONTROL.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND/OR DO NOT ALLOW THE EXCLUSION OR LIMITATION OF CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE.
ATTENTION
For your protection in the event of theft or loss of this product, please fill in the information below for you own personal records.
Model No._____________________________________________________________________
Serial No. _____________________________________________________________________
(Located on back or bottom side of unit.)
Date of Purchase _______________________________________________________________
Purchase Price _________________________________________________________________
Where Purchased _________________________________________________________________________________________________________________________________________________
1AC6P1P1829-L73E4/US (1098NI)
21605 Plummer Street,
Chatsworth, California 91311
Printed in Japan
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising