EasyAccess – 2 Door Card Reading Access Control

EasyAccess – 2 Door Card Reading Access Control
www.securefast.co.uk
PRODUCT DATA SHEET DS14-020
EasyAccess – 2 Door Card Reading Access Control System
The EasyAccess door entry system
with its internal power supply
allows a cost effective self contained
Access Control System to be quickly
installed with the minimum number
of boxes on the wall.
Because the card readers used are all remote
from the control unit and the lock control
circuits, a high degree of security is assured as
tampering with the card reader connections
will not affect the door locks.
Features & Benefits
•
•
•
•
•
•
•
•
•
•
•
•
•
1968 Card Capacity
Non-volatile Card Storage
Programmed via Panel Mounted Keypad
Easy to Programme
Two Door Control
Log-On Penalty Timer
1968 Card Storage Capacity
Integral Door Power Supply
Magstripe, Prox or Wiegand Cards
Tamper Alarm Output
Block Add and Delete Cards
Forced Door And Door Held Alarm Output
Non-Volatile System Memory
The Key Pad with a Yes/No programming
interface is equipped with LED and audio
feedback so minimal familiarity is required to
set up the system. Adding or removing cards
may be done singly or on a block basis using
the keypad. Cards may also be controlled by
means of the Learn/Forget cards function.
Programming Information
Via panel mounted keypad protected by a 6 digit
log-on code and 30 second penalty timer. An
LED function status indicator and audio sounder
are also provided.
Maintenance and installation are assisted by
use of pluggable barrier strip connections.
Doors can be unlocked from the keypad or via
the request to exit push button inputs for
momentary operation.
Product Code
AEZYACC1
EasyAccess 2 Door Controller
with 1.2Ah Battery
AEZYACC7
EasyAccess 2 Door Controller
with 7Ah Battery
Issue 1 – 19/04/2017
www.securefast.co.uk
PRODUCT DATA SHEET DS14-020
EasyAccess – 2 Door Card Reading Access Control System
Technical Information
Card Capacity
Dimensions (WxHxD)
Weight
Power Requirements
Internal Battery Backup
Lock Power Output
Overload Protection
Cable Entry
Data Storage
Current Protection
Power Status Indication
Mounting Position
Tamper Alarm
Card Formats
1968 Cards
202mm x 190mm x 75mm
AEZYACC1 (Including Battery) 2.83kg
AEZYACC7 (Including Battery) 4.9kg
Input: 210-250V ac, 40-70Hz @30VA from an unswitched Spur
Internal: 12V current consumption = 10ma, quiescent, 45ma. Maximum
EZAC-1 Includes 1.2Ah 12V Battery for use with ‘Fail Secure’ Lock Types
EZAC-7 Includes 7Ah 12V Battery for use with ‘Fail Secure’ Lock Types
1.8A at 13.8V ac
1 x 1A Mains Fuse, 1 x 1A Low Voltage AC Fuse, 1 x 2A Battery Fuse
2 Top, 2 Bottom & 1 in the Base (Via 20mm Knockouts)
Non-Volatile
Charger Protected by Electronics Shut Down & Battery Protected By Fuse
Via Two Front Panel LED’s (Green & Red)
Using any of the three internal, 4mm fixing holes
A Magnetic Tamper Sensor is Fitted to the Lid and an Open Collector Output
Provided for Driving a Remote 12V Sounder (0.3A Max)
Mag Stripe: Tower (Standard ISO), Tower (Bank ISO)
WIEGAND/PROX: 26 Bit, Tower (34 Bit)
For further information contact:
Securefast plc
Unit 6 & 7
The Cedars Business Centre
Avon Road, Cannock
Staffordshire
WS11 1QJ
Call> +44 (0) 1704 502801
Email > sales@securefast.co.uk
Visit > www.securefast.co.uk
Issue 1 – 19/04/2017
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising