KP-32 User`s Manual - RTS Intercom Systems

KP-32 User`s Manual - RTS Intercom Systems
USER INSTRUCTIONS
KP-32 KEYPANEL
UP TO AND INCLUDING VERSION 2.4.0
EKP-32 EXPANSION PANEL
LCP-32 LEVEL CONTROL PANEL
F.01U.193.253
Rev. 21
JUNE/2015
2
KP-32 Classic
PROPRIETARY NOTICE
The product information and design disclosed herein were originated by and are the property of Bosch Security Systems, Inc.
Bosch reserves all patent, proprietary design, manufacturing, reproduction, use and sales rights thereto, and to any article disclosed
therein, except to the extent rights are expressly granted to others.
COPYRIGHT NOTICE
Copyright 2015 by Bosch Security Systems, Inc. All rights
reserved. Reproduction, in whole or in part, without prior written
permission from Bosch is prohibited.
*All other trademarks are property of their respective owners.
WARRANTY AND SERVICE INFORMATION
THE LIGHTNING
FLASH AND
ARROWHEAD
WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
“DANGEROUS
VOLTAGE” INSIDE
THE PRODUCT.
CAUTION: TO REDUCE
THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE
COVER. NO USERSERVICABLE PARTS
INSIDE. REFER
SERVICING TO
QUALIFIED SERVICE
PERSONNEL.
THE
EXCLAMATION
POINT WITHIN
THE TRIANGLE
IS A WARNING
SIGN ALERTING
YOU OF
IMPORTANT
INSTRUCTIONS
ACCOMPANYIN
G THE PRODUCT.
SEE MARKING ON BOTTOM/BACK OF PRODUCT.
For warranty and service information, refer to the appropriate web
site below:
RTS Intercoms .............................. www.rtsintercoms.com/warranty
RTS Digital
RTSTW
AudioCom
RadioCom
Intercom Headsets.....................................................www.telex.com
WARNING: APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR
SPLASHING AND NO OBJECTS FILLED WITH LIQUIDS, SUCH AS
VASES, SHALL BE PLACED ON THE APPARATUS.
WARNING: THE MAIN POWER PLUG MUST REMAIN READILY OPERABLE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, GROUNDING
OF THE CENTER PIN OF THIS PLUG MUST BE MAINTAINED.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS APPRATUS TO RAIN OR MOISTURE.
CUSTOMER SUPPORT
Technical questions should be directed to:
WARNING: TO PREVENT INJURY, THIS APPARATUS MUST BE
SECURELY ATTACHED TO THE FLOOR/WALL/RACK IN ACCORDANCE
WITH THE INSTALLATION INSTRUCTIONS.
Customer Service Department
Bosch Security Systems, Inc.
www.telex.com
This product is AC only.
TECHNICAL QUESTIONS EMEA
Bosch Security Systems Technical Support EMEA
http://www.rtsintercoms.com/contact_main.php
DISCLAIMER
The manufacturer of the equipment described herein makes
no expressed or implied warranty with respect to anything
contained in this manual and shall not be held liable for any
implied warranties of fitness for a particular application or
for any indirect, special, or consequential damages. The
information contained herein is subject to change without
prior notice and shall not be construed as an expressed or
implied commitment on the part of the manufacturer.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
3
Important Safety Instructions
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this apparatus near water.
6.
Clean only with dry cloth.
7.
Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8.
Do not install near any heat sources such as radiators, heat registers, stoves,
or other apparatus (including amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of the obsolete outlet.
10.
Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
11.
Only use attachments/accessories specified by the manufacturer.
12.
Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
13.
Unplug this apparatus during lightning storms or when unused for long
periods of time.
14.
Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
4
Bosch Security Systems, Inc.
KP-32 Classic
User Manual
F.01U.193.253
Rev. 21
Table
of
Contents
INTRODUCTION ....................................................................................................................... 13
Description .............................................................................................................................................13
Features ..................................................................................................................................................13
Options ...................................................................................................................................................14

Connector Module ............................................................................................................................................. 14
OKI Option Card ............................................................................................................................................... 15
RVON Option Card ........................................................................................................................................... 15
CSI-100 Coaxial System Interface Module ....................................................................................................... 15
EKP-32 Expansion Keypanel ............................................................................................................................ 16
LCP-32/16 Level Control Panels ....................................................................................................................... 16
INSTALLATION ........................................................................................................................ 17
Upgrade the KP-32 Boot Loader Version ..............................................................................................17
Upgrade the Keypanel Firmware ...........................................................................................................18
Upgrade the OKI Board Firmware .........................................................................................................22
Rack Mount Considerations ...................................................................................................................23
Option DIP Switch Settings ...................................................................................................................24
Switch 1: Latch Enable/Disable ........................................................................................................................ 24
Switch 2: Key Gain Enable/Disable .................................................................................................................. 24
Switch 3: Screen Saver Enable/Disable ............................................................................................................. 24
Switch 4: Call Flash Timeout ............................................................................................................................ 24
Switch 5: Footswitch Enable/Disable* .............................................................................................................. 25
Switch 6: Keypad Mode Selection .................................................................................................................... 25
Switch 7: Test/Debug ........................................................................................................................................ 25
Switch 8: Test/Debug ........................................................................................................................................ 25
Address Switch Setting ..........................................................................................................................26
General Information .......................................................................................................................................... 26
Address Setting for Zeus ................................................................................................................................... 26
Address Setting for ADAM CS ......................................................................................................................... 26
ADAM CS with RJ12 or DB-9 back panel: ...................................................................................................... 26
ADAM CS with 50-pin Telco back panel: ........................................................................................................ 28
Address Setting for ADAM ............................................................................................................................... 28
Connections ............................................................................................................................................29
EXP AND LCP Connectors .............................................................................................................................. 29
Frame Connector ............................................................................................................................................... 29
Power Supply Connector ................................................................................................................................... 30
Headset Connector ............................................................................................................................................. 30
Headset Microphone Gain Adjustment .............................................................................................................30
Panel Microphone Connector ............................................................................................................................30
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
6

KP-32 Classic
Panel Microphone Gain Adjustment ................................................................................................................. 30
BASIC OPERATION ..................................................................................................................31
Screen Saver Operation .........................................................................................................................31
Selecting Headset or Speaker ................................................................................................................31
Listen Volume Adjustments ..................................................................................................................31
Intercom Keys and Displays ..................................................................................................................32
Alphanumeric Display Indications for Intercom Keys ...................................................................................... 32
Talk LED Indications ........................................................................................................................................ 32
Intercom Key Operation ........................................................................................................................33
Basic Operation ................................................................................................................................................. 33
Operation of Intercom Keys with Options ........................................................................................................ 34
Operation of Intercom Talk Keys with the Speaker or Headset DIM Setting .................................................. 35
Operation of Intercom Keys assigned to TIF Ports ........................................................................................... 35

Muting the Microphone .........................................................................................................................35
Call Waiting Operation ..........................................................................................................................36
TELEPHONE OPERATION .....................................................................................................37
Receiving A Phone Call .........................................................................................................................37
Dialing And Hanging Up Using Keypanel Keypad Sequences .............................................................37
Keypanel Manual Dial Sequence ...................................................................................................................... 37
KP9X Redial Sequence ..................................................................................................................................... 38
Keypanel Keypad Hang-up Sequence ............................................................................................................... 38
KP9X Autodial Sequences ................................................................................................................................ 38
Storing an Autodial Number in the TIF ............................................................................................................ 39
Storing an Autodial Number in the KP-32 ........................................................................................................ 39
Dialing an Autodial Number Stored in the TIF ................................................................................................. 39
Dialing And Hanging Up Using The KP-32 Dialing Menu ..................................................................40
Manual Dialing .................................................................................................................................................. 40
Redial ................................................................................................................................................................. 40

Autodial .................................................................................................................................................41
KP9X SERIES KEYPAD PROGRAMMING ............................................................................43
Keypad Programming, Display Requests ..............................................................................................43
Display Requests Using Keypad Sequences ..................................................................................................... 43
Display Panel ID ............................................................................................................................................... 43
Display Level 2 Talk Key Assignments ............................................................................................................ 43
Display Listen Key Assignments ...................................................................................................................... 43
Display Setup Page Assignments ...................................................................................................................... 44
Test Keys and Displays ..................................................................................................................................... 44
Tone Generator Activation (FUNC-DISPLAY-7) ............................................................................................ 45
Display Requests Using Scrolling ..................................................................................................................... 45
Keypad Programming, Assigning Setup Pages .....................................................................................46
Keypad Programming, Assigning Intercom Keys .................................................................................46
General .............................................................................................................................................................. 46
Assigning Keys Using Keypad Numeric Entry ................................................................................................. 47
Programming Key Assignments Using Copy ........................................................................................48
Copying an assignment from the call waiting Window to a Key ...................................................................... 48
Copying One Key Assignment to Another Key ................................................................................................ 48
Programming Key Assignments Using Alpha Scrolling .......................................................................48
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic

7
Prefix Scrolling ................................................................................................................................................. 49
Clearing a Key Assignment ............................................................................................................................... 50
KP-32 MENU SYSTEM ............................................................................................................. 51
Menu System, Menu Access ..................................................................................................................51
Menu System, Display Menu .................................................................................................................52
Display Menu, Asgn Type ................................................................................................................................ 52
Display Menu, Chans On .................................................................................................................................. 52
Display Menu, Key Groups ............................................................................................................................... 52
Display Menu, Key List .................................................................................................................................... 52
Display Menu, Level 2 ...................................................................................................................................... 52
Display Menu, Listen ........................................................................................................................................ 52
Display Menu, Matrix (Trunked Systems Only) ............................................................................................... 52
Display Menu, Panel ID .................................................................................................................................... 53
Display Menu, Version ..................................................................................................................................... 53
Menu System, Key Assign Menu ..........................................................................................................53
General Procedure to use the Key Assign Menu ............................................................................................... 53
Key Assign Menu, Matrix ................................................................................................................................. 55
Key Assign Menu, Pt-to-Pt ............................................................................................................................... 55
Key Assign Menu, Party Line ........................................................................................................................... 55
Key Assign Menu, IFB ...................................................................................................................................... 55
Key Assign Menu, Spcl List ............................................................................................................................. 55
Key Assign Menu, Sys Relay ............................................................................................................................ 56
Key Assign Menu, Camera ISO ........................................................................................................................ 56
Key Assign Menu, UPL Resrc .......................................................................................................................... 56
Key Assign Menu, IFSL .................................................................................................................................... 56
Key Assign Menu, Auto Func ........................................................................................................................... 56
Key Assign Menu, Key Gain ............................................................................................................................ 57
Key Assign Menu, Reset Vols .......................................................................................................................... 57
Key Assign Menu, Setup Page .......................................................................................................................... 58
Key Option Menu ..................................................................................................................................59
Key Option Menu, Auto Dial ............................................................................................................................ 59
Key Option Menu, Chime ................................................................................................................................. 59
Key Option Menu, Key Groups ........................................................................................................................ 60
Clearing a Key Group ....................................................................................................................................... 60
Key Option Menu, Solo .................................................................................................................................... 61
OMNEO Conn Menu (Available only with OKI Option Card Installed) ..............................................61
RVON Conn Menu (Available only with RVON Option Card Installed) .............................................62
Service Menu .........................................................................................................................................62
Service Menu, Aux Inputs (GPI Option Only) ................................................................................................. 62
Service Menu, Baud Rate .................................................................................................................................. 62
Service Menu, Caller Vol. ................................................................................................................................. 63
Service Menu, DIM ........................................................................................................................................... 63
Service Menu, Disply DIM ............................................................................................................................... 63
Service Menu, DSP Func .................................................................................................................................. 64
Service Menu, Hdst Sel ..................................................................................................................................... 66
Service Menu, LCP-32 ...................................................................................................................................... 66
Service Menu, Local GPIO ............................................................................................................................... 67
Service Menu, Matrix Out ................................................................................................................................. 68
Service Menu, Mic Select ................................................................................................................................. 69
Service Menu, Min Volume .............................................................................................................................. 69
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
8

KP-32 Classic
Service Menu, Mod Assign ............................................................................................................................... 69
Service Menu, OMNEO Setup (OKI Option Card Only) ................................................................................. 70
Service Menu, Output Level ............................................................................................................................. 72
Service Menu, Preamp Out (GPI Option Only) ................................................................................................ 72
Service Menu, Reset Cfg ................................................................................................................................... 72
Service Menu, RVON Setup (RVON Option Card Only) ................................................................................ 72
Service Menu, Save Cfg .................................................................................................................................... 73
Service Menu, Scr Saver ................................................................................................................................... 73
Service Menu, Sidetone ..................................................................................................................................... 73
Service Menu, Snoop Tally ............................................................................................................................... 74
Service Menu, Test Panel .................................................................................................................................. 74
Service Menu, Tone Gen ................................................................................................................................... 74
SPECIFICATIONS ....................................................................................................................75
Microphone Preamplifier .......................................................................................................................75
Tone Generator ......................................................................................................................................75
Headphone Amplifier ............................................................................................................................75
Speaker Amplifier and Speaker .............................................................................................................75
Intercom Input/Output ...........................................................................................................................76
External Line Input: (Program Input) ....................................................................................................76
General ...................................................................................................................................................76
AC Supply: ........................................................................................................................................................ 76
Environmental: .................................................................................................................................................. 76
Approvals: ......................................................................................................................................................... 76
Connectors (Other connector options available) ...................................................................................76
Panel Microphone Connector ............................................................................................................................ 76
Headset Connector ............................................................................................................................................ 76
Power Input Connector ...................................................................................................................................... 77
Intercom Connectors: Parallel-wired DE9S and RJ12 Connectors ................................................................... 77
Expansion Connector ........................................................................................................................................ 77
LCP Connector .................................................................................................................................................. 77
GPI Module Connectors (Optional) .......................................................................................................78

Aux 1 In (Auxiliary program input 1) ............................................................................................................... 78
Aux 2 In (Auxiliary program input 2) ............................................................................................................... 78
Relay 1 & 2 Out ................................................................................................................................................. 78
Relay 3 & 4 Out ................................................................................................................................................. 79
Opto 1-4 In (Opto-isolated control inputs) ........................................................................................................ 79
OC 1 & 2 Out (J2) ............................................................................................................................................. 80
Headset (External headset connector) ............................................................................................................... 80
Foot Switch/Speaker .......................................................................................................................................... 80
MIC In (J7) Unbalanced Panel Microphone Input ............................................................................................ 81
MIC Out (J8) Balanced Microphone Output ..................................................................................................... 81
KP9X KEYPAD SEQUENCE QUICK REFERENCE .............................................................83
KP9X Display Sequences ......................................................................................................................83
KP9X Setup Page Assignment .......................................................................................................................... 84
Key Assignments Using Keypad Numeric Entry .............................................................................................. 84
KP9X Phone Operation .........................................................................................................................85
KP9X Hang-up Sequence .................................................................................................................................. 85
KP9X Dial Sequence ......................................................................................................................................... 85
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic

9
KP9X Redial Sequence ..................................................................................................................................... 85
KP9X Autodial Sequences ................................................................................................................................ 85
KP-32 MENU SYSTEM QUICK REFERENCE ...................................................................... 87

Menu Access ..........................................................................................................................................87
Menu List ...............................................................................................................................................88
MODE 2 OPERATION .............................................................................................................. 89
Section 2 ................................................................................................................................................89
Switch 4: Call Flash Timeout* .......................................................................................................................... 89
Section 3 ................................................................................................................................................89

LED Indications for Intercom Keys .................................................................................................................. 89
GLOSSARY ................................................................................................................................. 91

OKI Option Card Installation ....................................................................................................................95
Install the OKI Option Card ...................................................................................................................95

RVON-1.....................................................................................................................................................99
General Description of the RVON-1 Voice Over Network Card ..........................................................99
Features ..................................................................................................................................................99
Specifications .......................................................................................................................................100
Default Addresses for the RVON Product Line ..................................................................................101
Dip Switches ........................................................................................................................................101
Firmware Compatibility Requirements for the RVON-1 Card ...........................................................102
Flash Chip Replacement ......................................................................................................................102
Installation of the RVON-1 Card .........................................................................................................103
RVON-1 Relay ................................................................................................................................................ 104
Addresses and the RVON-1 .................................................................................................................104
Configure the RVON-1 from the KP-32 ..............................................................................................105
Top Level Menu, Service, RVON Setup ......................................................................................................... 105
Top Level Menu, RVON Conn. ...................................................................................................................... 106
Configure the RVON-8 via AZedit to contact the RVON-1 ...............................................................107
Download RVON-1 Firmware Through AZedit .................................................................................108

Basic Network Configuration ..................................................................................................................111
Basic Network Configuration ..............................................................................................................111
LAN vs. WAN ................................................................................................................................................. 111
Accessing The Wide Area Network (WAN) ................................................................................................... 113
Ports ................................................................................................................................................................. 113
IP Addresses .................................................................................................................................................... 115
Ping a Computer .............................................................................................................................................. 116
Possible Pitfall With Routers, Gateways, And Switches ................................................................................ 117
RVON Configuration ...........................................................................................................................118
Network Terminology ..........................................................................................................................119

Telnet & Serial Port Programming ..........................................................................................................121
RVON Serial and Telnet Commands ...................................................................................................121
Setup ................................................................................................................................................................ 121
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
10
KP-32 Classic
How to Configure the RVON-1 using Telnet ......................................................................................122

EKP-32 Expansion Panel.........................................................................................................................127
Installation Instructions ........................................................................................................................127
Specifications .......................................................................................................................................128
AC Supply ....................................................................................................................................................... 128
Power Consumption ....................................................................................................................................... 128
General ............................................................................................................................................................ 128
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
List
of
Figures
FIGURE 1.
FIGURE 2.
FIGURE 3.
FIGURE 4.
FIGURE 5.
FIGURE 6.
FIGURE 7.
FIGURE 8.
FIGURE 9.
FIGURE 10.
FIGURE 11.
FIGURE 12.
FIGURE 13.
FIGURE 14.
FIGURE 15.
KP-32 Keypanel Front View. ........................................................................................... 14
KP-32 GPI Connector Module .......................................................................................... 14
OKI Option Card ............................................................................................................... 15
RVON Option Card .......................................................................................................... 15
KP-32 CSI-100 Coaxial System Interface Board ............................................................. 15
EKP-32 Expansion Keypanel Front View ........................................................................ 16
LCP-32/16 Level Control Panel Front View .................................................................... 16
DE9S Intercom Cable Wiring ........................................................................................... 29
RJ12 Intercom Cable Wiring ............................................................................................ 29
Setup page usage for the KP-32 and the first EKP-32 ...................................................... 44
LCP-32 correspondence to KP-32 and EKP-32 ................................................................ 66
Flash Chip placement on the KP-32 motherboard .......................................................... 102
Local Area Network Diagram ......................................................................................... 112
Wide Area Network Diagram ......................................................................................... 112
Network Address Translation ......................................................................................... 113
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
12
Bosch Security Systems, Inc.
KP-32 Classic
User Manual
F.01U.193.253
Rev. 21
CHAPTER 1
Introduction
Description
The RTS Model KP-32 Keypanel fits in a standard 19 inch rack and is two (2) rack units high. It has 32 lever keys: 30 keys are
for intercom talk/listen assignment; one (1) key is for call waiting response; and one (1) key is for 
headset/microphone/program selection and volume setup. The KP-32 combines all of the programmable features of the KP9X
Series Keypanels and the KP-12 Keypanel. It adds significant new features such as DSP (Digital Signal Processing) and
binaural headset operation with left/right assignment of audio signals. The KP-32 also introduces large, super-bright, long-life
fluorescent displays with adjustable brightness control, making it suitable for all types of ambient lighting from direct sunlight
to darkness.
Features
Super-bright, fluorescent
displays
Provide much better visibility and usable life than LCD displays. A display saver mode
with programmable scrolling message extends display life and conserves power during
periods of inactivity.
32 lever keys, with 30 keys
available for full talk/listen
configuration
Doubles the number of channels over the KP9X series keypanels. Keys support both
latching (hands-free) and momentary (push-to-talk) operation.
Enhanced programming
keypad
Provides the complete KP9X keypad sequences, plus new keypad sequences, plus an
extensive scrollable menu system. Menus include helpful prompts to walk the user
through setup.
Only 90mm deep behind the
front panel (approximately
130mm with connectors)
Perfect for consoles, OB vans, etc.
Digital Signal Processing
Improves microphone voice activation and limiting. Adds new mixing, metering, and
filtering capabilities.
Binaural (5-pin) Headset
Connector
Works with the DSP mixing feature. Lets you independently assign intercom,
microphone, and program audio to left or right headphone.
NOTE: Monaural (4-pin) connector available as an option. For monaural operation, the mixer lets you select which
items are monitored in the headphones.
Easy upgrades
Bosch Security Systems, Inc.
Firmware updates can be received via the internet, for example, and then downloaded to
the KP-32 via the intercom connection.
User Manual
F.01U.193.253
Rev. 21
14 Introduction
FIGURE 1.
KP-32 Classic
KP-32 Keypanel Front View.
Options
Connector Module
FIGURE 2.
KP-32 GPI Connector Module
Provides connectors for two (2) line-level audio inputs (program 1 and 2), an unswitched, balanced microphone preamplifier
output, an external headset, an external speaker output, and a foot switch input (for remote switch activation of all armed talk
keys, or just one [1] key). Also includes General Purpose Input/Output (GPIO), with four (4) opto-isolated inputs, two (2)
open-collector outputs, and two (2) SPDT (Single Pole Double Throw) relay outputs. Inputs can activate single keys and
groups of keys. Outputs can activate external devices from keypanel keys or from GPI inputs. Available factory installed or as
an add-on kit.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
Introduction 15
OKI Option Card
FIGURE 3.
OKI Option Card
Provides two (2) Ethernet and one (1) LC Fiber connectors used to connect to the Matrix, adding up to two (2) additional 
full-duplex audio channels that can be mixed with audio in the keypanel.
RVON Option Card
FIGURE 4.
RVON Option Card
Provides up to two (2) additional full-duplex audio channels that can be mixed with audio in the keypanel.
CSI-100 Coaxial System Interface Module
FIGURE 5.
KP-32 CSI-100 Coaxial System Interface Board
Provides the ability to link the unit to the matrix using a single 75 coaxial cable. The interface converts all audio and data
streams to a single transmission path. Perfect for systems where there are existing, but unused 75 video cable. Requires a
CSI-200 interface unit at the intercom matrix end.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
16 Introduction
KP-32 Classic
EKP-32 Expansion Keypanel
FIGURE 6.
EKP-32 Expansion Keypanel Front View
Provides an additional 32 intercom keys for a total of up to 128 keys (up to three [3] EKPs to a KP-32 depending on the
intercom configuration).
LCP-32/16 Level Control Panels
FIGURE 7.
LCP-32/16 Level Control Panel Front View
Provides easy adjustment of point-to-point and party line listen levels for individual intercom keys. One (1) LCP-32/16 adjusts
one (1) row of keys.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
Installation 17
CHAPTER 2
Installation
Upgrade the KP-32 Boot Loader Version
IMPORTANT:
This upgrade must be done before upgrading the firmware of the KP-32 unit for OKI Option Card use.
To upgrade the KP-32 boot loader, do the following:
1.
Verify the KP-32 is powered Off.
2.
On the back panel of the KP-32, set DIP switch 8 to On.
For more information on dip switch settings, see “Option DIP Switch Settings” on page 24.
3.
Power On the unit.
A message indicating “This panel needs a firmware download” appears.
4.
In AZedit, from the Status menu, select Software Versions.
The Software Versions popup menu appears.
5.
From the Software Versions popup menu, select Keypanels.
The Keypanel Version Information window appears.
NOTE: Notice the Version column displays the message “NEEDS DOWNLOAD next to the version string.
6.
Right-click the KP-32 version you want to upgrade.
A popup menu appears.
7.
From the popup menu, select Download Firmware....
The Firmware Download navigation window appears.
8.
Navigate to and select your firmware file (for example, KP-32.hex).
9.
Click Open.
The Download Device Firmware window appears.
10.
Click Begin Download.
The download begins and a popup message appears.
11.
Click OK.
The KP-32 firmware download finishes.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
18 Installation
KP-32 Classic
NOTE: Use the Keypanel Version Information window to follow the progress of the download (the number and
percentage chunks completed). Also the download progress is displayed on the KP-32 display window until
the download is complete.
12.
On the back panel of the KP-32, set DIP switch 8 to Off.
IMPORTANT:
Do not power-cycle the keypanel until it has finished reprogramming the flash. Damage to the flash
chips may occur, rendering the unit inoperable and replacement of the flash chips necessary.
NOTE: Once the download is complete and the panel has reprogrammed the flash, the boot loader restarts.
13.
Power cycle the unit.
14.
Verify the version in AZedit.
The version displays as v0.1.0.
Upgrade the Keypanel Firmware
IMPORTANT:
The keypanel firmware must be updated before you install the OKI module into the keypanel.
To download firmware to the keypanel, do the following:
1.
Open AZedit.
2.
From the Status menu, select Port.
The Port Status window appears.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
Installation 19
3.
Find the port number where the KP-32 is assigned.
4.
Highlight the Port (keypanel) to be updated.
You may select more than one (1) at a time by holding CTRL key down while you select.
5.
Right-click the highlighted selections.
A popup menu appears.
6.
Select Download Firmware.
The Firmware Download window appears.
7.
Using the browse button, browse to the file to be downloaded.
8.
Click Open.
The Download Device Firmware window appears.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
20 Installation
KP-32 Classic
9.
Click Begin Download.
The download begins.
10.
Click OK.
The KP-32 firmware download finishes.
NOTE:
•
This can take up to 30 minutes to complete. Use the Keypanel Version Information window to follow
the progress of the download.
•
The KP-32 resets itself once the firmware download is complete.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
11.
Installation 21
Verify the version upgrade in the Keypanel Version Information window is correct.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
22 Installation
KP-32 Classic
Upgrade the OKI Board Firmware
NOTE:
If you have not installed the OKI-2 Option Board, see “OKI Option Card Installation” on page 95. The OKI-2
Option card must be installed in the keypanel to update the firmware.
To upgrade the OKI board firmware, do the following:
1.
From the Status menu, select Port.
The Port Status window appears.
2.
Right-click the port where the OKI KP-32 Classic keypanel is assigned.
A popup menu appears.
3.
From the popup menu, select Download OMNEO....
A User Access Control warning appears.
NOTE: If this is the first time running the Firmware Upload Tool, do the following:
a.
In the Browse for Folder window, navigate and select the Firmware Upload Tool folder.
b.
Click OK.
A select network interface message appears.
c.
From the Network adapter drop down menu, select the network interface you want to use.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
Installation 23
4.
Click OK.
The Firmware Upload Tool appears.
5.
Select the OKI Device you want to upload the new firmware to.
6.
Click Upload.
You can watch the progress of the upload in the Progress column.
Rack Mount Considerations
Elevated Operating Ambient -
If installed in a closed or multi-unit rack assembly, the operating ambient temperature of
the rack environment may be greater than room ambient. Therefore, consideration
should be given to installing the equipment in an environment compatible with the TMA
(Maximum Ambient Temperature) specified by the manufacturer.
Reduced Air Flow -
Installation of the equipment in a rack should be such that the amount of air flow
required for safe operation of the equipment is not compromised.
Mechanical Loading -
Mounting of the equipment in the rack should be such that a hazardous condition is not
achieved due to uneven mechanical loading.
Circuit Overloading -
Consideration should be given to the connection of the equipment to the supply circuit
and the effect that overloading of the circuits might have on over-current protection and
supply wiring. Appropriate consideration of equipment nameplate ratings should be
used when addressing this concern.
Reliable Earthing -
Reliable earthing of rack mounted equipment should be maintained. Particular attention
should be given to supply connections other than direct connections to the branch circuit
(e.g., use of power strips).
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
24 Installation
KP-32 Classic
Option DIP Switch Settings
NOTE:
When the switch is open, the physical switch is in the up position. When the switch is closed, the physical switch
is in the down position.
Switch 1: Latch Enable/Disable
Default setting = Open: enable
Description: An intercom key can always be turned on for momentary conversation by pressing and holding the key during the
conversation. There is also an electronic latching feature that lets you tap intercom keys to turn them on or off. This permits
convenient hands-free conversation. However, it can also result in a talk circuit being left on unintentionally. For example a
key that talks to a public address system could be accidentally left on. Or an IFB key (a type of key assignment often used by
a director or producer to give instructions to a listener, such as a news anchor during a television broadcast) could accidentally
be left on, causing confusion for the IFB listener. To prevent such accidents, the latching feature can be turned off.
NOTE:
DIP switch 1 disables latching for the entire keypanel. If you just need to disable latching for selected keys, leave
DIP switch 1 in the Open position. Then, disable latching for the desired keys using the D check boxes in the
Keypanels/Ports setup screen of AZedit.
Switch 2: Key Gain Enable/Disable
Default setting = Open: enable
Description: Enables or disables the Key Gain item in the Key Assign menu.
Switch 3: Screen Saver Enable/Disable
Default setting = Open: enable
With Screen Saver enabled, the KP-32 shuts off the display and enters a low power state after delay can be set between 30
minutes and 12 hours The display reactivates instantaneously on an incoming call or when the keypanel operator actuates any
control. As with all fluorescent and back-lit LCD displays, some dimming occurs after many years of operation. Using the
screen saver helps maximize the display life.
Switch 4: Call Flash Timeout
Default setting = Open: 15 second flash.
Description: Whenever there is an incoming call and there is a talk key assigned to the caller, the talk LED next to the key
flashes. The flash can be set for a 15 second timeout, or until the caller's talk key is released.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
Installation 25
Switch 5: Footswitch Enable/Disable*
Default = Open: disabled
Description: The optional Connector Module has a footswitch (GRP CALL) input. If the footswitch is enabled (DIP switch 5
set to the closed position), the keys latched on do not activate until the footswitch is closed. Latched keys are indicated by an
amber talk LED, and when the footswitch is activated, the LEDs provide the normal 
talk-on indication.
NOTE:
•
If the talk key is held down in Footswitch mode the channel is activated until the user releases the key.
The use of this function does not require the footswitch to be used.
•
•
If DIP switch 1 is set to the CLOSED position, nothing latches.
Individual keys can be set to non-latching via AZedit. If this is done, the footswitch has no effect on the
keys that have been set to non-latching.
Switch 6: Keypad Mode Selection
Settings: Open = Classic Keypad, Closed = Standard
Description: In Classic mode, the keypanel functions operate as called out in the main portion of this manual. If the switch is
closed, the functions operate as outlined in this manual with slight modifications. Any function that is affected by Standard
Mode operation has an asterisk (*) by it. The changes/modifications to the functionality is called out in “Mode 2 Operation” on
page 89.
Switch 7: Test/Debug
Default Setting: Open.
Switch 8: Test/Debug
Default Setting: Open.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
26 Installation
KP-32 Classic
Address Switch Setting
General Information
In Zeus, ADAM and ADAM-M Intercom Systems with AIO-8 and AIO-16 with SCSI breakouts, intercom ports are arranged
in groups of eight (8). All ports in a group share a common data port. Each KP-32 is uniquely identified on the data port by the
setting of its address switch. The method of determining the proper address switch setting varies for each intercom system.
Use the method for your intercom system as described below. Then set the white pointer on the Address switch to point to the
correct setting.
TABLE 1. Keypanel
Addressing
Manually Addressed
Automatically Addressed
You must manually address the keypanel when using the
following:
•
•
•
•
The keypanel is automatically addressed when using the
following:
AIO-8 on ADAM
•
•
•
•
AIO-16 SCSI on ADAM
Zeus I
Zeus II
•
•
AIO-16 MDR on ADAM
ADAM-M
Cronus
RVON Product Line – RVON-8, RVON-1,
RVON-C, RVON-16
OMNEO Product Line
Zeus III and Zeus III LE
Address Setting for Zeus
Intercom port connectors on the Zeus back panel are arranged in three (3) groups of eight (8) intercom ports. For each group,
intercom port connectors are labeled ID 1, ID 2, etc. When you connect a KP-32 to Zeus, set the Address switch to match the
corresponding ID number on the Zeus back panel.
NOTE:
Address switch settings 0, and 9 through F are not used.
Address Setting for ADAM CS
Each Audio I/O card contains one (1) group of eight (8) intercom ports. However, the method of breaking out the groups
depends on the type of connectors on the back panel.
ADAM CS with RJ12 or DB-9 back panel:
The intercom port connectors are arranged in groups of eight (8). The first connector at the left for each group is Address 1, the
next is Address 2, and so forth.
NOTE:
Address switch settings 0, and 9 through F are not used.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
Number vs. Intercom Port Numbers for 8-Port Audio I/O Cards (ADAM and ADAM CS Intercom Systems)
Address
User Manual
F.01U.193.253
1
1
2
3
4
5
6
7
8
2
9
10
11
12
13
14
15
16
3
17
18
19
20
21
22
23
24
4
25
26
27
28
29
30
31
32
5
33
34
35
36
37
38
39
40
6
41
42
43
44
45
46
47
48
7
49
50
51
52
53
54
55
56
8
57
58
59
60
61
62
63
64
1
2
3
4
5
6
7
8
26
201
202
203
204
205
206
207
208
27
209
210
211
212
213
214
215
216
28
217
218
219
220
221
222
223
224
29
225
226
227
228
229
230
231
232
30
233
234
235
236
237
238
239
340
31
241
242
243
244
245
246
247
248
32
249
250
251
252
253
254
255
256
33
257
258
259
260
261
262
263
264
1
2
3
4
5
6
7
8
51
401
402
403
404
405
406
407
408
52
409
410
411
412
413
414
415
416
53
417
418
419
420
421
422
423
424
54
425
426
427
428
429
430
431
432
55
433
434
435
436
437
438
439
440
56
441
442
443
444
445
446
447
448
57
449
450
451
452
453
454
455
456
58
457
458
459
460
461
462
463
464
1
2
3
4
5
6
7
8
76
601
602
603
604
605
606
607
608
77
609
610
611
612
613
614
615
616
78
617
618
619
620
621
622
623
624
79
625
626
627
628
629
630
631
632
80
633
634
635
636
637
638
639
640
81
641
642
643
644
645
646
647
648
82
649
650
651
652
653
654
655
656
83
657
658
659
660
661
662
663
664
18
137
138
139
140
141
142
143
144
19
145
146
147
148
149
150
151
152
20
153
154
155
156
157
158
159
160
21
161
162
163
164
165
166
167
168
22
169
170
171
172
173
174
175
176
23
177
178
179
180
181
182
183
184
24
185
186
187
188
189
190
191
192
25
193
194
195
196
197
198
199
200
43
337
338
339
340
341
342
343
344
44
345
346
347
348
349
350
351
352
45
353
354
355
356
357
358
359
360
46
361
362
363
364
365
366
367
368
47
369
370
371
372
373
374
375
376
48
377
378
379
380
381
382
383
384
49
385
386
387
388
389
390
391
392
50
393
394
395
396
397
398
399
400
68
537
538
539
540
541
542
543
544
69
545
546
547
549
550
551
552
553
70
553
554
555
556
557
558
559
560
71
561
562
563
564
565
566
567
568
72
569
570
571
572
573
574
575
576
73
577
578
579
580
581
582
583
584
74
585
586
587
588
589
590
591
592
75
593
594
595
596
597
598
599
600
93
737
738
739
740
741
742
743
744
94
745
746
747
748
749
750
751
752
95
753
754
755
756
757
758
759
760
96
761
762
763
764
765
766
767
768
97
769
770
771
772
773
774
775
776
98
777
778
779
780
781
782
783
784
99
785
786
787
788
789
790
791
792
100
793
794
795
796
797
798
799
800
Installation 27
Rev. 21
1
2
3
4
5
6
7
8
Card Numbers (bold headings) and Port Numbers
Cards 1-25
9
10
11
12
13
14
15
16
17
65
73
81
89
97
105 113 121 129
66
74
82
90
98
106 114 122 130
67
75
83
91
99
107 115 123 131
68
76
84
92
100 108 116 124 132
69
77
85
93
101 109 117 125 133
70
78
86
94
102 110 118 126 134
71
79
87
95
103 111 119 127 135
72
80
88
96
104 112 120 128 136
Cards 25-50
34
35
36
37
38
39
40
41
42
265 273 281 289 297 305 313 321 329
266 274 282 290 298 306 314 322 330
267 275 283 291 299 307 315 323 331
268 276 284 292 300 308 316 324 332
269 277 285 293 301 309 317 325 333
270 278 286 294 302 310 318 326 334
271 279 287 295 303 311 319 327 335
272 280 288 296 304 312 320 328 336
Cards 51-75
59
60
61
62
63
64
65
66
67
465 473 481 489 497 505 513 521 529
466 474 482 490 498 506 514 522 530
467 475 483 491 499 507 515 523 531
468 476 484 492 500 508 516 524 532
469 477 485 493 501 509 517 525 533
470 478 486 494 502 510 518 526 534
471 479 487 495 503 511 519 527 535
472 480 488 496 504 512 520 528 536
Cards 76-100
84
85
86
87
88
89
90
91
92
665 673 681 689 697 705 713 721 729
666 674 682 690 698 706 714 722 730
667 675 683 691 699 707 715 723 731
668 676 684 692 700 708 716 724 732
669 677 685 693 701 709 717 725 733
670 678 686 694 702 710 718 726 734
671 679 687 695 703 711 719 727 735
672 680 688 696 704 712 720 728 736
F.01U.193.253
Bosch Security Systems, Inc.
TABLE 2. Address
28 Installation
KP-32 Classic
ADAM CS with 50-pin Telco back panel:
Determine the address setting from Table 2. To use the table, locate the intercom port number to which the KP-32 is
connected. Then, read across to the Address column to find the Address number. Set the KP-32 Address switch to this number.
NOTE:
Address switch settings 0, and 9 through F are not used.
Address Setting for ADAM
Each Analog I/O card contains one (1) group of eight (8) intercom ports (except for AIO-16 cards). Determine the address
setting from Table 2 on page 27.
NOTE:
•
To use the table, locate the intercom port number to which the KP-32 is connected. Then, read across to the
Address column to find the Address number. Set the KP-32 Address switch to this number.
•
Address switch settings 0, and 9 through F are not used.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
Installation 29
Connections
EXP AND LCP Connectors
Connect from the EXP connector on the back of the KP-32 to the Expansion 1 connector of an optional EKP-32 Expansion
Panel. Use the interconnect cable supplied with the Expansion Panel. The Expansion 2 connector on the Expansion Panel can
connect to a second or third Expansion Panel, but no more than 128 intercom keys can be operated per intercom port.
Each LCP-32/16 adjusts the listen levels for 16 keypanel keys, and you can connect as many LCP-32 panels as required to
adjust all keys on the KP-32 and on an optional EKP-32 Expansion Panel. An interconnect cable is supplied with each
LCP-32. Connect the first LCP-32 to the LCP connector on the KP-32. Connect the second LCP-32 to the first LCP-32, and so
forth.
NOTE:
When arranging LCP-32 panels in an equipment rack, you should put them directly above or below the keys the
unit is used to adjust.
Frame Connector
Use the Frame connectors (one at time) to connect to an intercom port of the intercom system. The intercom port you connect
to should agree with the address that you set previously. Cable wiring diagrams are shown in Figure 8 and Figure 9.
FIGURE 8.
DE9S Intercom Cable Wiring
FIGURE 9.
RJ12 Intercom Cable Wiring
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
30 Installation
KP-32 Classic
Power Supply Connector
At power-up, the alphanumeric displays first show asterisks (****). After several seconds the intercom key assignments
display.
If the keypanel cannot establish communication with the intercom system, all alphanumeric displays continue to show
asterisks. Check the keypanel to matrix cable connection if this occurs. If the keypanel loses communications with the
intercom, it does not revert to ****’s for 30 seconds. If there is a short disruption in the data communications, the panel does
not show ****’s at all (although the panel my briefly display ----’s).
The power supply accepts 100-240 VAC, 50/60Hz.
To connect the keypanel to power, do the following:
1.
Align and insert the external power supply connector.
2.
Tighten the locking ring.
3.
Connect a power cord to the power supply and to an AC power source.
Headset Connector
A stereo headset may be connected for use along with or in place of the front panel speaker and a separate microphone.
Headphones may be connected for use with a separate microphone.
Headset Microphone Gain Adjustment
The gain of the headset microphone preamp can be adjusted via the recessed trim pot located on the back panel. Turn the pot
clockwise to increase gain and counter-clockwise to decrease gain. The limits are ±20dB from nominal.
Panel Microphone Connector
A panel microphone may be connected for talking with either the front panel speaker or headphones used for listening. The
connector accepts MCP5, MCP6, or MCP90 Panel Microphones. Insert the microphone and rotate the entire microphone body
several turns to lock in place.
Panel Microphone Gain Adjustment
The gain of the panel microphone preamp can be adjusted via the recessed trim pot located on the back panel. Turn the pot
clockwise to increase gain and counter-clockwise to decrease gain. The limits are ±20dB from nominal.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
CHAPTER 3
Basic Operation
Screen Saver Operation
If the KP-32 is set for screen saver operation, the alphanumeric display can be configured to automatically shut off after 30
minutes or 12 hours of inactivity. The display reactivates on incoming call or when the keypanel operator actuates any control.
DIP switch 3 enables/disables screen saver operation.
NOTE:
You can override the normal timeout period for screen saver operation and immediately place the keypanel in
screen saver mode. See “Service Menu, Disply DIM” on page 63.
Selecting Headset or Speaker
The Headset/Speaker display alternates between Hdst and Spkr with each key tap.
To alternate between Hdst and Spkr, do the following:
>
Tap the Headset/Vol. Sel. key upward. 
The headset LED lights when the headset is selected and is off when the speaker is selected.
Listen Volume Adjustments
By default, the Vol. control adjusts the listen volume for the speaker or headset, whichever appears in the Vol. Sel. display. The
level of auxiliary program inputs 1 & 2 (if GPI/O board is present and Aux inputs are enabled) and the level of incoming audio
from the intercom matrix (if enabled) can be adjusted.
To adjust the listen volume, do the following:
1.
Press the Vol. Sel. button until the desired source appears in the Vol. Sel. display (Aux1, Aux2, or Icom).
2.
Using the Vol. control, adjust the listen volume.
NOTE:
•
The Vol. control defaults back to the speaker or headset after about thirty seconds of inactivity of the
control. The minimum volume level for either the keypanel speaker or headset may be adjusted. See
“Service Menu, Min Volume” on page 69.
•
You can save the volume adjustments to be the power-up defaults using “Service Menu, Save Cfg” on
page 73.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
32 Basic Operation
KP-32 Classic
Intercom Keys and Displays
Alphanumeric Display Indications for Intercom Keys
Upper Case Letters:
Upper case letters indicate keys that have any kind of talk assignment, with or without a
corresponding listen assignment. Example: DIR1
NOTE: Keypanels operating in Unicode can display both upper and lower-case characters for talk assignments.
Lower Case Letters:
Lower case letters indicate keys that have only a listen assignment. Example: dir1.
Dashes ----:
Dashes indicate a key that has no talk or listen assignment.
Flashing Alphanumeric Display: This means the key is activated to talk to an IFB or ISO, the IFB, ISO, or PL is in use, a
call via a trunk line (depending on configuration) is active, or an incoming call from a
P-P or PL.
NOTE: The flashing alphanumeric display for TIF keys, remote IFB keys, and remote ISO keys can be disabled by
selecting the Don't generate tallies for TIF and trunk use check box in AZedit (Options menu|Intercom
Configuration|Options tab).
Talk LED Indications
The talk LED is the lower LED for each key. The LED indications are as follows:
LED
Description
Continuous
Green*
Talk is on and the keypanel operator can be heard at the destination.
Continuous Red
Talk LED &
Flashing Display
Alpha (In-use)*
The key is off, but someone is talking to the destination. This indication is provided for any local PL,
IFB, ISO, or TIF key. This indication is provided so keypanels operators know when critical director
communications are occurring. If you activate the key, either of two things happen:
• If you activate the key and the talk LED turns continuous green, this indicates that you and
the other keypanel operator are both talking to the destination.
• IFB keys only: If the talk LED flashes red when an IFB key is activated, this indicates that
the other keypanel has a higher IFB priority and you cannot talk at this time.
The red in-use indication for TIF keys can be disabled in AZedit on the Options tab of the Intercom
Configuration window. Select the Don't generate tallies for TIF and trunk use check box. This also
disables the flashing alpha display when talking to remote IFBs or ISOs as previously described. This
causes a first birthday.
Flashing Red
Talk LED &
Flashing Display
Alternating
Pattern of Alpha
& (-**-) (Busy)
You cannot talk at this time. This indication occurs when you activate a local IFB key that is already
in-use by a keypanel with a higher IFB priority. It also occurs when you activate any key assigned to
a remote destination, but there are currently no trunks available. As well as when a TIF phone line is
ringing.
Flashing Green
Talk LED &
Display Alpha
(on time equal to
off time)*
There is an incoming call from the destination assigned to the key. Activate the key to talk back.
The duration of incoming call flash is controlled by DIP switch 4 on the KP-32 back panel. See
“Option DIP Switch Settings” on page 24.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
Basic Operation 33
LED
Description
Blinking Amber
Talk LED (on
time less than off
time)*
Indicates a key is ready to talk (key is on), but requires external footswitch activation to talk.
Listen LED
Indication
The listen LED is the upper LED for each key. The listen LED is green when the listen key is on.
Intercom Key Operation
Basic Operation
The up position of an intercom key activates listen (if assigned). The down position activates talk (if assigned). If there is no
talk assignment for an intercom key, the talk position of the key does not activate. If there is no listen assignment, the listen
position does not activate.
To activate a key momentarily, do the following:
1.
Press and hold a key.
2.
Release the key when finished.
To latch a key, do the following:
1.
Tap a key.
The key turns on and remains on.
2.
Tap the key again to turn it off.
NOTE: Latching may be turned off for the entire keypanel by setting DIP switch 1 on the KP-32 back panel to the
Closed position. Latching may be disabled for individual keys on a keypanel using AZedit.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
34 Basic Operation
KP-32 Classic
Operation of Intercom Keys with Auto Functions
NOTE:
Assignment of keys with auto functions is described in the programming sections that follow. Descriptions of the
auto functions are also contained in the “Glossary” on page 91.
Operation of keys with auto functions is as follows:
Talk + auto follow
Talk and listen can be activated separately. The listen assignment listens to whatever is
assigned to the talk key.
Talk + auto listen
Both talk and listen activate when talk is activated.
Talk + auto mute
Listen turns off when talk is activated.
Talk + auto reciprocal
Listen is always on, and talk may be turned on or off.
Talk + auto table
If an IFB talk key has an auto-table listen assignment, talk and listen can be independently
activated. When the listen key is turned on, the IFB listen source is switched to the IFB listen
destination for the panel (which may be itself, or it may be defined as a separate output of the
intercom).
All Call Key
Activating the key also activates all keys to the left of it (up to, but not including another 
all-call key).
Talk + DIM
If a point-to-point key has the DIM function as a level 2 talk assignment, activating the talk
key causes the crosspoint levels to diminish for any other intercom ports currently listening to
the same destination and are in the same DIM table as the caller.
Operation of Intercom Keys with Options
Group Option Keys
Activating the master key in a key group activates all keys in that group according to each key's individual key assignment.
Activating a slave key does not affect any other keys in the group.
Solo Key
Activating a key with the solo option causes all other keys on the keypanel to turn off until the solo key is turned off.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
Basic Operation 35
Operation of Intercom Talk Keys with the Speaker or Headset DIM Setting
Activating any talk key causes the speaker or headphone volume at this keypanel to diminish by the amount specified in the
DIM menu item on the Service menu.
NOTE:
Do not confuse this with the Talk+DIM auto function previously described. Talk+DIM affects the speaker or
headphones on other keypanels when a particular talk key is activated on this keypanel. Speaker DIM affects the
speaker or headphone level on this keypanel when any talk key on this keypanel is activated.
Operation of Intercom Keys assigned to TIF Ports
If an intercom key is assigned to talk to an intercom port that is designated as a TIF port in AZedit, placing the key in the talk
position activates the KP-32 dialing menu. See “Telephone Operation” on page 37, for further information.
NOTE:
Designate an intercom port as a TIF port by selecting the Port is TIF check box in AZedit.
Muting the Microphone
To mute the microphone, do the following:
>
Tap the MUTE key up to turn microphone muting on or off. 
The Mute LED turns solid red and the Vol. Sel. display alternates between Hdst and Mute (or between Spkr and Mute)
while the microphone is muted.
NOTE: While muting is on, you cannot be heard on the intercom, by anyone on the telephone, or by any device
connected to the mic preamp output of the optional connector module.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
36 Basic Operation
KP-32 Classic
Call Waiting Operation
Occasionally, a keypanel may call, and there won't be a key assigned to talk back to the caller. In this case, the caller's name
appears in the call waiting window.
To answer a call in the call waiting window, do the following:
>
Press down and hold the call waiting key.
To clear the call waiting window, do the following:
>
Tap the call waiting key up.
If a second call is received in the call waiting window while a caller name is already displayed, the call waiting LED flashes
red.
To answer a second call, do the following:
1.
Tap up on the key to clear the first name.
2.
Hold the key down to talk to the second caller.
NOTE:
•
By default, only the names of callers who are not currently assigned to intercom keys appears in the call
waiting window. Alternatively, you can force all caller names to display in the call waiting window.
This is controlled by the AZedit check box titled Always Stack Callers In Call Waiting Window.
•
We recommend that you do not stack all callers in the call waiting window.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
CHAPTER 4
Telephone Operation
IMPORTANT:
Telephone operations require an optional TIF Telephone Interface. Also, you must first assign a 
talk/listen key on the keypanel with a TIF assignment. We recommend a talk+auto listen assignment.
Receiving A Phone Call
When there is an incoming telephone call, the talk LED flashes red next to the KP-32 key assigned to the TIF. Activate the key
to answer the call.
Alternatively, there is an audible indication generated by the TIF unit for incoming calls.
NOTE:
The red flash for incoming TIF call is the default operation. Alternatively, a continuous-red talk LED indication
can be provided. This is accomplished by selecting the check box Don't generate tallies for TIF or Don’t
Generate tallies for Trunk Use in AZedit (Options|Intercom Configuration|Options). This check box also affects
other tally indications.
Dialing And Hanging Up Using Keypanel Keypad Sequences
Keypanel Manual Dial Sequence
To manually dial the keypanel, do the following:
1.
Activate the TIF listen key. 
The listen LED should be on. Verify the TIF talk key is off.
2.
On the keypad, tap CLR + PHONE + PGM.
3.
Latch on the TIF talk key.
The talk LED turns green, the TIF goes off-hook, and a dial tone is heard at the KP-32 is heard.
4.
Using the keypad, dial the telephone number. 
Digits scroll in the display above the TIF key. When the far end answers, dial additional digits (to access a voicemail
system or automated response system, etc.).
5.
Momentarily turn the TIF key off to end dialing mode.
6.
Turn the TIF talk key back on for conversation.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
38 Telephone Operation
KP-32 Classic
To end the call, do the following:
1.
Turn the TIF talk key off.
2.
Tap PHONE + CLR.
3.
Tap the TIF talk key. 
The TIF key talk and listen indicators turns off and the TIF hangs up. The TIF is now ready for another call.
KP9X Redial Sequence
To redial a phone number, do the following:
IMPORTANT:
The last dialed phone number is always stored at the TIF and overwrites any previously dialed phone
number. If several people have access to the TIF, redial may not produce the results that you expect!
1.
Tap up on the TIF key to activate listen.
2.
Tap PHONE+PGM.
3.
Tap the TIF talk key
4.
Tap CLR + 0 + 0. 
The last phone number is re-dialed.
5.
After the number has dialed, tap the TIF talk key to end dialing mode.
6.
Tap down on the TIF key to activate talk.
Keypanel Keypad Hang-up Sequence
To disconnect the keypanel, do the following:
1.
Turn off the TIF talk key. 
Tap down to toggle talk off. The talk LED should be off.
2.
On the keypad, tap PHONE+CLR.
3.
Momentarily turn the TIF talk key on, then off. 
The TIF key talk and listen indicators turns off and the TIF hangs up.
NOTE: You can use the hang up sequence to hang up the TIF even if you did not place or answer the call.
KP9X Autodial Sequences
NOTE:
Unlike the autodial operations using the KP-32 menu system, which store telephone numbers locally within the
KP-32, the KP9X autodial operations work with telephone numbers that are stored at the TIF. The advantage to
saving at the TIF is that many users can access a common set of stored telephone numbers. A disadvantage is
users can easily over-write important telephone numbers.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
Telephone Operation 39
Storing an Autodial Number in the TIF
To store an autodial number in the TIF, do the following:
1.
Tap PHONE+PGM.
2.
Tap the TIF talk key to latch it on.
3.
Dial the phone number you want to store.
The entire phone number sequence can have up to 30 digits.
NOTE: To insert one (1) or more pauses anywhere in the dialing sequence, enter CLR + 9 + 9 for each pause. A
pause may be required, for example, if you need to enter a digit to get an outside line and your phone system
requires a pause before continuing to dial. If you are using credit card dialing, several pauses may also be
required between the phone number and your personal access code.
4.
After dialing the telephone number, click CLR + PGM, then enter a 2-digit number (01, 02, etc. up to 32, 24 for the
TIF-2000A) you want to use as the autodial number.
5.
After storing the autodial number, use the keypanel hang-up sequence to end the call.
Storing an Autodial Number in the KP-32
To store an autodial number in the KP-32, do the following:
1.
Press Menu.
Display appears in the call waiting window.
2.
Using the arrow keys, scroll to Key Option.
3.
Press PGM.
Auto Dial appears in the call waiting window.
4.
Press PGM.
Phone#? appears in the call waiting window.
5.
Dial the phone number, including the area code, and any additional dialing procedures.
6.
Press FWD.
7.
Using the arrow keys, scroll to the Auto Dial position to which you want to save the phone number (1 through 10).
8.
Press PGM.
#X saved appears (where X represents the auto dial position)
9.
From the Service menu, select Save Cfg to save the auto dial number.
Dialing an Autodial Number Stored in the TIF
To dial an autodial number, do the following:
1.
Tap the PHONE+PGM+TIF key to activate dialing mode.
2.
Tap down on the TIF talk key to latch it in the on position.
3.
Tap CLR followed by the autodial number (01, 02, etc.).
4.
When finished dialing, click the TIF talk key again to exit dialing mode.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
40 Telephone Operation
KP-32 Classic
Dialing And Hanging Up Using The KP-32 Dialing Menu
The dialing menu only activates when talking to an intercom port that has the Port is TIF check box activated in AZedit.
Manual Dialing
To manual dial, do the following:
1.
Turn on the TIF talk key. 
Manual Dial displays in the call waiting window. Icom ADial appears if displayed if the Intercom supports it.
2.
Tap the PGM key. 
Dial#? displays, and the dial tone should be audible in your speaker or headset.
NOTE:
•
•
3.
To hang up at any time after this point: tap the BACK key. Hang Up displays, then tap PGM.
While using the phone, any incoming intercom calls to the call waiting window go into the call waiting
stack. Incoming calls sent to the stack force the KP-32 to exit dial mode. The caller names are not be
displayed, but the call waiting LED flashes red. You may either hang up the phone and answer the
intercom call, or continue with the phone call and answer the intercom call afterward.
Dial the phone number.
Digits appear in the call waiting window as you dial. Dialing tones are audible in the speaker or headset. If the far
end answers, begin your conversation.
NOTE: After the far end answers, you may dial additional digits (to retrieve voice mail, log onto an automated
answering system, etc.).
4.
If there is no answer, or to hang up when finished talking, tap the BACK key. 
Hang Up displays.
5.
Tap PGM to hang up.
NOTE: Occasionally, you may receive intercom caller names in the call waiting window while you are talking on
the phone. In this case, the dialing menu options are cleared from the call waiting window, and the Hang Up
option won't be available. Instead of trying to reenter the menu system, use the “Keypanel Manual Dial
Sequence” on page 37.
Redial
1.
Turn TIF talk key on. 
Manual Dial displays in the call waiting window. Icom ADial appears if displayed if the Intercom supports it.
2.
Using the arrow keys, scroll to Redial.
3.
Tap PGM.
If the far end answers, begin your conversation. Hang Up displays.
NOTE: After the far end answers, you may dial additional digits (to retrieve voice mail, log onto an automated
answering system, etc.).
4.
Tap CLR to exit Hang Up Mode.
5.
Turn the TIF talk off, then on.
6.
Enter manual dial mode.
7.
Tap PGM to hang up.
NOTE: Occasionally, you may receive an intercom caller name in the call waiting window while you are talking on
the phone. In this case, the dialing menu options are cleared from the call waiting window, and the Hang Up
option won't be available. Instead of trying to reenter the menu system, use the “Keypanel Manual Dial
Sequence” on page 37.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
Telephone Operation 41
Autodial
NOTE:
Autodial is only available after you have saved autodial numbers.
To autodial a number, do the following:
1.
Turn the TIF talk key on. 
Manual Dial displays in the call waiting window.
2.
Using the arrow keys, scroll to Local ADial.
The Autodial menu only displays when a number has been programmed into the Autodial Key Option.
3.
Tap PGM.
4.
Using the arrow keys, select the desired autodial number.
5.
Tap PGM.
If the far end answers, begin your conversation.
NOTE: After the far end answers, you may dial additional digits (to retrieve voice mail, log onto an automated
answering system, etc.).
6.
Tap CLR to exit Hang Up Mode.
7.
Turn the TIF talk off, then on.
8.
Enter manual dial mode.
9.
Tap PGM to hang up.
NOTE: Occasionally, you may receive an intercom caller name in the call waiting window while you are talking on
the phone. In this case, the dialing menu options are cleared from the call waiting window, and the Hang Up
option won't be available. Instead of trying to reenter the menu system, use the “Keypanel Manual Dial
Sequence” on page 37.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
42 Telephone Operation
Bosch Security Systems, Inc.
KP-32 Classic
User Manual
F.01U.193.253
Rev. 21
CHAPTER 5
KP9X Series Keypad Programming
NOTE:
See “KP9X Keypad Sequence Quick Reference” on page 83.
Keypad Programming, Display Requests
Display requests let you view information about the keypanel configuration. You can display information by two (2) methods:
•
•
Entering sequences on the programming keypad.
Scrolling the names of display requests in the call waiting window. The scrolling method also gives you
access to additional features that are not available with the keypad sequences.
Display Requests Using Keypad Sequences
All display request sequences start with FUNC DISPLAY (0 8 ).
Display Panel ID
FUNC DISPLAY 1
This sequence displays the port number. If the Address switch is incorrectly set, the wrong Panel ID displays.
Display Level 2 Talk Key Assignments
FUNC DISPLAY 2
This sequence displays all level 2 talk key assignments for about 10 seconds. Lev2 displays in the call waiting window.
Display Listen Key Assignments
FUNC DISPLAY 3
This sequence displays all listen key assignments for about 10 seconds. Lstn displays in the call waiting window.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
44 KP9X Series Keypad Programming
KP-32 Classic
Display Setup Page Assignments
FUNC DISPLAY E-PNL
Currently, there are four (4) setup pages available for each keypanel, configurable up to 15 pages. Each setup page defines a
set of 16 talk and listen key assignments. One (1) setup page is typically assigned to the main keypanel, and is referred to as
the Main setup page. Additional setup pages are assigned to any connected expansion panels, and are referred to as Expansion
1, Expansion 2, etc.). Since the KP-32 requires two (2) setup pages, it uses the main page assignments and also one (1)
expansion page. The EKP-32 uses two (2) additional expansion pages.
FIGURE 10.
Setup page usage for the KP-32 and the first EKP-32
When you enter the sequence FUNC DISPLAY E-PNL, the call waiting window displays Mn-1 or Mn-2, etc. This indicates
which setup page is currently being used at the Main position. After a few moments X1-1, or X1-2, etc displays. This indicates
which setup page is currently being used by Expansion 1. Next, if there is an expansion panel connected, X2-1, or X2-2, etc
displays, followed by X3-1 or X3-2, etc to indicate the setup page usage for expansion 2 and expansion 3and any other
expansion panels.
NOTE:
To change the setup page assignments, see “Keypad Programming, Assigning Setup Pages” on page 46.
Test Keys and Displays
FUNC DISPLAY 0
When you enter this sequence, all alpha-numeric displays show a % symbol. Pressing down on any key
(except the Headset/Vol. Sel. key) cause OK to display. This verifies operation of the key. Tapping up or down on the 
Headset/Vol. Sel. key causes the display to cycle through the available selections.
If latching is enabled, tapping up or down on any intercom key, or the call waiting key, causes the corresponding red LED to
light. This verifies latching operation and also that the each red LED is OK.
Holding any key in the up or down position causes the corresponding green LED to light. This verifies operation of the green
LEDs.
NOTE:
This sequence is similar to “Service Menu, Test Panel” on page 74, except the service menu test also lets you
check the operation of the keypad buttons.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
KP9X Series Keypad Programming 45
Tone Generator Activation (FUNC-DISPLAY-7)
FUNC DISPLAY 7
This sequence activates the keypanel's internal tone generator. You can use the tone generator to check the audio send and
receive paths to and from the matrix. For example, you can assign a talk key on the keypanel to talk to itself. When you
activate the talk key, you should be able to hear the tone from the keypanel speaker or headset.
To turn off the tone generator, do the following:
>
Press the CLR key.
NOTE:
The microphone input is turned off when the tone generator is active.
Display Requests Using Scrolling
The display requests can be accessed using scrolling. Scrolling offers several additional features. To use scrolling, tap FUNC
DISPLAY followed by the up or down arrow keys to scroll through the list of display requests, and then tap PGM to select the
current item. The display request names appears in the call waiting window as follows:
ID:
Displays the port number.
Lev 2:
Displays level 2 talk assignments.
Lstn:
Displays listen assignments.
Name:
Displays a list of crosspoints closed to this keypanel.
Type:
Displays level 1 talk key assignment types.
Mtx:
Displays matrix ID for all level 1 talk assignments.
Tone:
Turns on tone generator. CLR to quit and turn off tone generator.
Epnl:
Displays setup page assignments. Mn=KP-32 bottom row keys, X1=KP-32 top row keys, X2=EKP-32
bottom row keys, X3=EKP-32 top row keys.
Gain:
After selecting this item, tap up on any listen key with a point-to-point or party line assignment. The
current listen gain from this keypanel to the intercom port or party line displays in the call waiting
window. Use the up or down arrow keys to change the gain. Tap another listen key to start adjusting the
listen volume. Tap the CLR key or turn off the current key to exit.Use VRst to reset all gains.
VRst:
Reset all port / party line gains to 0dB.
Asgn:
Displays a list of key assignments that are set up for this keypanel, but not currently accessible. This
includes talk level 1 assignments on setup pages that are not currently assigned, and any key assignment
that might be obscured by the call-waiting window. You can scroll through the list using the up or down
arrow keys. Then use the call waiting key to talk to the currently selected destinations.
Test:
Test keys and displays.
Vxxx:
Display keypanel firmware version.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
46 KP9X Series Keypad Programming
KP-32 Classic
Keypad Programming, Assigning Setup Pages
1.
Tap the E-PNL (8) key.
2.
Select a setup page number (tap 1, or 2, etc).
3.
Tap the PGM key.
4.
Tap any key in the row of keys where you want to assign the setup page.
NOTE: The same setup page cannot be assigned in more than one (1) place. If a setup page is already assigned
somewhere else, you must clear or change that assignment first. With the exception of the main row
assignment, you can clear any page assignment from a row of keys by entering E-PNL 0 PGM, then
pressing any key in the row.
•
If you cannot change the setup page assignments for a particular keypanel, this feature may be
restricted in AZedit.
•
To display setup page assignments at any time, see “Display Setup Page Assignments” on
page 44.
Keypad Programming, Assigning Intercom Keys
General
There are three (3) methods to assign intercom keys with keypad programming. These methods are summarized below and
explained on the following pages.
Key Assignment using Keypad Numeric Entry:
Using this method, you enter the panel number, party line number etc.
that you wish to assign to a key. This method requires you know the
number (not the name) of the port, party line etc. that you wish to
assign. Since most users do not have access to this information, this
method of key assignment is not recommended.
Key Assignment by Copying an Assignment:
Using this method, you can copy an assignment from one (1) key to
another. You can also use this method to transfer an incoming call to a
talk key and/or listen key.
Key Assignment using Alpha Scrolling:
Using this method, you scroll through lists of alpha names in the call
waiting window and select the name of the panel, party line etc. you
want to assign. Then you copy the name to a key. If descriptive names
have been assigned using the intercom system configuration software,
alpha scrolling is easiest to use.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
KP9X Series Keypad Programming 47
Assigning Keys Using Keypad Numeric Entry
NOTE:
Each programming step must be completed within 4-5 seconds. Otherwise, the programming sequence is
discarded.
General Procedure
1.
For talk level 2 assignment only: Tap 0 0. Otherwise, skip this step.
2.
Select the key assignment type:
3.
4.
NUM
Intercom port
PL
Party line
AUTO
Auto function
FUNC SLIST
Special list.
FUNC IFB
IFB
FUNC ISO
Camera ISO
FUNC RELAY
Relay or GPI output.
Auto function assignment only: Tap an additional number to select the desired auto function:
1
Auto listen (listen keys only)
2
Auto follow (listen keys only)
3
Auto mute (listen keys only)
4
Auto reciprocal (listen keys only)
5
All call (talk level 1 only)
6
DIM (talk level 2 only, for point-to-point key, must enter 00 first)
7
Auto table (listen only, when talk level 1 is an IFB assignment)
Trunked intercoms only: When assigning auto functions or local key assignments, skip this step. Select an intercom
matrix (tap 1, or 2, etc.).
NOTE: Intercom system numbers are the numbers that appear in the Icm column in Trunk Edit when you select
Status or Setup from the Intercoms menu.
5.
(Skip when assigning auto functions.) Tap one or more number keys to select the desired port number, party line
number, etc.
NOTE: If the destination is in a remote matrix, you must always enter exactly three (3) digits for a port number, or
exactly two (2) digits for anything else. For example, to assign port 1 you must enter 0 0 1; for party line 1
you must enter 0 1.
6.
Tap PGM.
7.
Tap down on a key change the talk assignment for that key. Tap up to change the listen assignment.
NOTE:
•
If a key does not accept an assignment, the destination you are trying to assign may not be scroll
enabled in AZedit, or, the key you are trying to assign may be restricted in AZedit.
•
Auto functions are always assigned in the local intercom system, even when used with keys assigned to
a remote intercom system. For example, you can program a talk key to talk to a remote party line, and
then program the listen key using auto-listen on the local intercom. Pressing the talk key automatically
activates listening for the remote party line.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
48 KP9X Series Keypad Programming
KP-32 Classic
Programming Key Assignments Using Copy
There are two (2) ways to copy key assignments:
•
•
Copy an assignment from the call waiting window to another key.
Copy a key's assignment to another key.
Copying an assignment from the call waiting Window to a Key
1.
While the caller's name is displayed in the call waiting window, tap the COPY CW key.
2.
Tap the key to which you want to copy. 
The name of the caller appears in the display below the key.
NOTE:
If a key does not accept an assignment, the assignment to assign may not be scroll enabled in
AZedit. Or, the key you are trying to assign may be restricted in AZedit.
Copying One Key Assignment to Another Key
1.
Tap the FUNC key.
2.
Tap the EX COPY key.
3.
Press the talk or listen key from which you wish to copy.
4.
Press the talk or listen key to which you wish to copy. 
The name of the key assignment appears in the display above the key.
NOTE:
If a key does not accept an assignment, the destination you are trying to assign may not be scroll
enabled in AZedit. Or, the key you are trying to assign may be restricted in AZedit.
Programming Key Assignments Using Alpha Scrolling
Alpha scrolling allows the user to scroll through a list of names of ports, party lines etc. in the call waiting window. Once the
desired name is displayed in the window, you can copy it to a key. There are four (4) scrolling modes:
•
•
•
•
EXAMPLE:
intercom
type
prefix
single-step
Assign a port to a key using the various scrolling modes.
To intercom scroll, do the following:
1.
If the port is located in a remote intercom system, tap FUNC  or FUNC to enter intercom scroll mode and
scroll up or down the list of intercoms in the call waiting window.
2.
Tap PGM to select the P-P list for that intercom.
OR
Tap FUNC TYPE to step through the list of function types.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
KP9X Series Keypad Programming 49
To type scroll, do the following:
1.
When the desired intercom system name is displayed, or when making an assignment in the local intercom system,
tap FUNC TYPE to activate type scroll mode.
2.
Using the arrow keys, scroll to the desired type of assignment (for example, P-P).
Abbreviations for types of key assignments:
•
•
•
•
•
•
•
•
3.
P-P:
PL:
IFB:
SPCL:
RLY:
ISO:
UR:
IFSL:
Point-to-Point
Party Line
IFB
Special List
Relay or GPI output
ISO
UPL Resource
IFB Special List
Press PGM to retrieve the requested list. 
Pressing PGM also exits type scroll mode and places the keypanel in single-step scroll mode. In some cases, WAIT
displays briefly while the requested list is being retrieved. N/A may display if the selected list is empty (or all the items
are restricted).
To scroll in single-step, do the following:
1.
Using the arrow keys, select the intercom port.
NOTE: If you cannot locate the destination you are looking for, it may not be scroll enabled in AZedit.
2.
Copy the selected port to a talk or listen key:
a.
Tap COPY.
b.
Tap down on an intercom key to assign talk.
OR
Tap up to assign listen.
Prefix Scrolling
When the keypanel is in single-step scroll mode, it may take a long time to scroll to the desired name (this is particularly true
of point-to-point lists). To speed up the process, you can use prefix scroll mode. Prefix scrolling mode scrolls through a list in
alpha-numeric order, but displays only the first occurrence of each 2-character prefix. For example, if your intercom system
had users CAM1, CAM2, CAM3, DIR1, DIR2; prefix scrolling would display CAM1 followed by DIR1. Once you locate a
desired 2-character prefix using prefix scroll, you can switch back to single-step scrolling to make your final selection.
To enter PREFIX mode, do the following:
1.
Tap PREFIX to enter prefix scroll mode.
2.
Using the arrow keys, scroll until you locate a name with the same first two (2) characters as the name for which
you are looking.
3.
Tap the PGM key to return to single-step scrolling mode.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
50 KP9X Series Keypad Programming
KP-32 Classic
Clearing a Key Assignment
There are two (2) ways to clear a key assignment:
Method 1: Clearing the Call Waiting Window and Copying it to a Key
1.
Clear the call waiting window, if necessary.
2.
Tap up on the call waiting key until it is empty.
3.
Tap the COPY CW key.
4.
Tap the key you want to clear. 
Tap up to clear listen, down to clear talk.
NOTE: If a key does not clear, it is probably restricted using the R check box in AZedit.
Method 2: Copying a Blank Key Assignment to the key you want to Clear
1.
Tap the FUNC key.
2.
Tap the EX COPY key.
3.
Tap an unassigned key.
4.
Tap the key you want to clear. 
Tap up to clear listen, down to clear talk.
NOTE: If a key does not clear, it is probably restricted using the R check box in AZedit.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
CHAPTER 6
KP-32 M ENU S YSTEM
NOTE:
A chart of the menu system is located at the back of the manual for quick reference.
Menu System, Menu Access
1.
Clear all names from the call waiting display (if not clear) by tapping up one (1) or more times on the call waiting
key.
2.
Tap MENU to activate the menu system.
3.
Press the page down arrow to scroll forward through the list of menus. Press the page up arrow to scroll back.
4.
Tap FWD or PGM to enter a menu. Tap BACK to exit a menu.
5.
Within a menu:
•
•
•
Press the up or down arrow keys to scroll.
Tap FWD or PGM to select an item.
Tap BACK to cancel a selection or to go back to the previous menu level.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
52 KP-32 Menu System
KP-32 Classic
Menu System, Display Menu
Use this menu to display information about the keypanel configuration.
Display Menu, Asgn Type
Asgn Type displays the talk level 1 assignment types for all keys. Abbreviations for the key assignment types appear in the
alphanumeric displays as follows:
•
•
•
•
•
•
•
•
•
NOTE:
P-P: Point-to-point talk key
PL: Party line talk key
IFB: IFB talk key
SPCL: Special list talk key
RLY (System relay): The key activates a GPI output at the intercom frame, or a relay output at a 
UIO-256 or FR9528 frame
ISO: Camera ISO talk key
IFSL: IFB Special List key
UPL: UPL resource key
AC: All-call key
For descriptions of the various key assignment types, see “Glossary” on page 91.
Display Menu, Chans On
Chans On displays an alpha list, in the call waiting window, of all intercom ports with talk crosspoints closed to this keypanel.
Chans On is typically used to locate an open mic or other open audio source. The most likely cause is typically a talk key left
on at some keypanel. In this case, use the up or down arrow keys to scroll through the list of names. You can then press the call
waiting key to ask the person at the other end to turn off their talk key.
Display Menu, Key Groups
Key Groups displays the master and slave keys associated with a configured key group.
To display key groups, do the following:
1.
Using the arrow keys, select group you want to see.
2.
Press FWD or PGM to display the group. 
The talk and listen LEDs of the master key is lit red and the talk and listen LEDs for the slave keys are lit green.
Display Menu, Key List
Key List displays and allows access to all the other assignments on the other keypanel pages that are not currently showing in
the keypanel display.
Display Menu, Level 2
Level 2 displays the talk level 2 assignments for all keys.
Display Menu, Listen
Listen displays the listen assignments for all keys.
Display Menu, Matrix (Trunked Systems Only)
Matrix displays the intercom system name for all talk level 1 key assignments. In non-trunked intercom systems, the intercom
system name can be LOCL (local), ZEUS, ZUS3, ADAM, or CRON. In trunked intercom systems, intercom system names are
created in TrunkEdit (Intercoms menu, Names.)
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
KP-32 Menu System 53
Display Menu, Panel ID
Panel ID displays the port number the keypanel is connected to. If the Address switch is incorrectly set, the wrong Panel ID
displays. Panel ID also displays the port alpha in brackets if the port is not scroll restricted.
Display Menu, Version
Version displays the firmware version of the keypanel.
NOTE:
For firmware upgrades, contact your intercom system dealer. For more information, see “Upgrade the Keypanel
Firmware” on page 18.
Menu System, Key Assign Menu
The Key Assign menu is used to assign intercom keys, adjust listen levels for point-to-point and party line keys, and to assign
setup pages.
General Procedure to use the Key Assign Menu
To use the key assign menu, do the following:
1.
Tap up on the call waiting key to clear the call waiting window.
2.
Tap MENU.
3.
Using the up and down arrow keys, scroll to Key Assign.
4.
Tap PGM.
NOTE: If you do not have a trunking intercom system, skip to step 6.
Remote key assignment only (trunking systems only): If your intercom system is configured for trunking,
Matrix displays in the call waiting window. You must select a remote intercom matrix before assigning
intercom keys to destinations in that matrix. You do not need to select an intercom matrix if you are
assigning keys in your own intercom system. Also, do not select an intercom matrix if you are assigning auto
functions or setup pages, or if you are changing listen gains for remote point-to-point keys or remote party
line keys. Select a matrix as follows:
a.
Press PGM to access the Matrix list.
b.
Using the arrow keys, locate the desired matrix.
c.
Press PGM to select a matrix. Wait may display while the scroll lists for that matrix are loading.
Pt-to-Pt appears in the call waiting window (both for local and remote key assignment). This is the list of available
point-to-point key assignments.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
54 KP-32 Menu System
5.
KP-32 Classic
Using the up or down arrow, select a different list as follows:
Pt-to-Pt
Assign a key to talk/listen to another intercom port.
Party Line
Assign a key to talk/listen to a party line.
IFB
Assign a key to talk/listen to an IFB.
Spcl List
Assign a key to talk/listen to a special list.
Sys Relay
Assign a key to activate a relay or GPI output.
Camera ISO Assign a key to talk/listen to an ISO.
UPL Resrc
Assign a key to activate a UPL resource.
IFSL
Assign a key to activate a IFB special list resource.
Auto Func
Assign an auto function to a key. (If you select this item, skip the rest of this procedure and go
to “Key Assign Menu, Auto Func” on page 56.)
Key Gain
Adjust the listen gain for a key that already has a point-to-point or party line assignment. (If
you select this item, skip the rest of this procedure and go to “Key Assign Menu, Key Gain” on
page 57.)
Reset Vols
Restore the default listen level for keys that have a point-to-point or party line assignment. (If
you select this item, skip the rest of this procedure and go to “Key Assign Menu, Reset Vols”
on page 57.)
Setup Page
Change the setup page assignments. (If you select this item, skip the rest of this procedure and
go to “Key Assign Menu, Setup Page” on page 58.)
6.
Tap PGM. 
In some cases, Wait appears while the requested list is uploaded from the intercom system.
7.
Using the arrow keys, locate the desired assignment.
8.
Tap PGM.
Talk Lvl 1 appears in the call waiting window.
9.
Using the up or down arrow key,if necessary, select a different option. Options are as follows:
•
•
•
•
•
•
•
Talk Lvl 1: Assigns only talk level 1. Leaves the listen assignment as is.
Listen: Assigns only listen. Leaves the talk assignment as is.
Talk + AF: Assigns talk level 1, with auto-follow listen.
Talk + AL: Assigns talk level 1, with auto-listen.
Talk + AM: Assigns talk level 1, with auto-mute listen.
Talk + AR: Assigns talk level 1, with auto-reciprocal listen.
Talk Lvl 2: Assigns talk level 2.
NOTE: If you attempt to assign talk level 2 to a key and there is no talk level 1 assignment, your assignment goes on
talk level 1. If you change the talk level 1 assignment for a key that also has a talk level 2 assignment, the
talk level 2 assignment is erased.
10.
Tap PGM.
Tap Key appears.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
11.
KP-32 Menu System 55
Tap any available intercom key.
Tap down for any kind of talk key assignment. Tap up for a listen-only key assignment.
IMPORTANT:
•
If you assign any type of talk key, the assignment name appears in the alphanumeric display above the
key.
•
If you add a listen assignment to an existing talk assignment, the listen assignment appears briefly in the
alphanumeric display to confirm the assignment, and then the talk assignment reappears.
•
If you assign a listen only key, the assignment name appears briefly in uppercase letters, and then
changes to lowercase letters.
When reassigning keys remember to remove any Chime, Solo, or Key Group options if they are not
needed for the new key assignment.
Key Assign Menu, Matrix
Matrix appears only for trunked intercom systems. A remote intercom matrix must be selected before assigning intercom keys
to destinations in that matrix.
You do not need to select matrix to assign keys to destinations in your own matrix. You also do not need to select a matrix
when assigning an auto function to a key.
Key Assign Menu, Pt-to-Pt
Pt-to-Pt assigns a talk or listen key to another intercom port. Some pt-to-pt destinations may be non-keypanel devices that
cannot activate talk and listen paths. Therefore, if you want full communication, you may need to assign both talk and listen on
the key.
Key Assign Menu, Party Line
Party Line assigns a key with talk and/or listen to a party line.
NOTE:
If you want full communication with the party line, you must assign both talk and listen on the key. If all
communications are 2-way, you may wish to assign the key as Talk + auto listen.
Key Assign Menu, IFB
By default, all IFBs are restricted and Not Avail displays when you attempt to select this item. To see IFBs you must check the
appropriate Scroll Enable check boxes in AZedit.
Key Assign Menu, Spcl List
Spcl List assigns a key with talks and/or listens to a special list. The key has no effect until members have been assigned to the
special list in AZedit.
NOTE:
Special list members may be non-keypanel devices that cannot themselves activate talk and listen paths.
Therefore, if you want full communication with all members of the special list, you may need to assign both talk
and listen on the key.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
56 KP-32 Menu System
KP-32 Classic
Key Assign Menu, Sys Relay
Sys Relay refers to any of several types of control devices existing in the intercom system, including:
•
•
•
•
The 8 GPI outputs from an ADAM Frame (J11 on the XCP-ADAM-MC Breakout Panel).
The 8 GPI outputs of an ADAM CS frame (J903 on the ADAM CS back panel).
The relay outputs of an FR9528 Relay Frame (RELAY OUTPUTS connector on the FR9528 back panel).
The 16 GPI outputs of a UIO-256 Universal Input/Output Frame (J5 on the UIO-256 back panel).
Key Assign Menu, Camera ISO
By default, all ISOs are restricted and Not Avail displays when you attempt to select this item. To see ISOs you must select the
appropriate Scroll Enable check boxes in AZedit. To see ISO resources you must check the appropriate Scroll Enable check
boxes in AZedit.
Key Assign Menu, UPL Resrc
By default, all UPL resources are restricted and Not Avail displays when you attempt to select this item. To see UPL resources
you must select the appropriate Scroll Enable check boxes in AZedit. (
Key Assign Menu, IFSL
By default, all IFSL resources are restricted and Not Avail displays when you attempt to select this item. To see IFSL resources
you must select the appropriate Scroll Enable check boxes in AZedit.
Key Assign Menu, Auto Func
Auto Func is used to assign a function that occurs when another function is performed.
To assign an Auto Func, do the following:
1.
Starting at the Key Assign menu item, use the up or down arrow keys to select Auto Func.
2.
Press PGM.
3.
Using the arrow keys, locate the desired auto function:
•
•
•
•
•
•
•
4.
AutoFollow (AF, for listen keys only)
Auto Listn (AL, for listen keys only)
Auto Mute (AM, for listen keys only)
Auto Recip (AR, for listen keys only)
Auto Table (AT, for listen keys only)
All Call (AC, for talk level 1 only)
DIM (DIM Table function, for talk level 2 on point-to-point keys only)
Press PGM.
Tap Key displays.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
5.
KP-32 Menu System 57
Tap an intercom key to assign the selected auto function.
Tap up to assign all auto functions except All Call or DIM. Tap down for All Call or DIM.
NOTE:
6.
•
If the assignment is successful, the abbreviation for the auto function appears in the alphanumeric
display for that key. However, if you try to assign the same function to a key that is already
programmed, the assignment is ignored. The assignment is ignored if the key you are trying to assign
has been restricted in AZedit.
•
Trunked intercom systems: Do not select a matrix before assigning auto functions. All auto functions
are assigned using the local matrix menus.
•
You do not need to run Save Cfg to store auto function assignments. These are stored in the intercom
system.
•
For descriptions of the auto functions, see the “Glossary” on page 91.
You can tap CLR to exit and return to normal operation.
OR
Tap BACK to return to the auto function menu and make more assignments.
Key Assign Menu, Key Gain
Key Gain is used to adjust the listen gains for point-to-point or party line keys. The key to adjust must already have a 
point-to-point or party line listen assignment.
To adjust key gain, do the following:
1.
Using the arrow keys, select Key Gain.
2.
Press PGM.
Tap Key displays.
3.
Tap up on the key you want to adjust.
The current listen level displays in the call waiting window.
4.
Using the arrow keys, change the listen level.
Tap additional point-to-point or party line keys to change their listen levels. 
OR
Tap CLR to quit.
NOTE: You do not need to run Save Cfg to store key gain changes. These are stored in the intercom system.
Key Assign Menu, Reset Vols
The Reset Vols menu item simultaneously resets gain levels for all point-to-point or party line keys.
To reset vols, do the following:
1.
Using the arrow keys, select Reset Vols.
2.
Press PGM.
Done displays. All key gains are now reset to the default level.
3.
Tap CLR to quit.
NOTE: You do not need to run Save Cfg after resetting key gains. These settings are stored in the intercom system.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
58 KP-32 Menu System
KP-32 Classic
Key Assign Menu, Setup Page
Setup Page is used to change the setup page assignments on the KP-32 or EKP-32. For example, one (1) setup page is used for
the top row of keys, and another setup page is used for the bottom row.
To change the setup page assignments, do the following:
1.
Using the arrow keys, select Setup Page.
2.
Press PGM.
Page 1 displays.
3.
Using the arrow keys, select any setup page action desired:
Page 1:
Assign setup page 1 to the KP-32 or EKP-32.
Page 2:
Assign setup page 2 to the KP-32 or EKP-32.
Page 3:
Assign setup page 3 to the KP-32 or EKP-32.
Page 4:
Assign setup page 4 to the KP-32 or EKP-32.
Clear Page:
Clear a page assignment from the KP-32 or EKP-32.
NOTE: The intercom can be configured for up to 15 setup pages.
4.
Tap PGM. 
Tap Key displays.
5.
Tap any key in the row where you want to assign the setup page.
The key assignments for that page should appear in the displays.
6.
Using the arrow keys, select and assign another setup page. 
OR
Tap CLR to exit.
NOTE: You do not need to run Save Cfg to store changes to setup pages. These are stored in the intercom system.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
KP-32 Menu System 59
Key Option Menu
Key Option Menu, Auto Dial
Auto Dial is used store auto dial numbers.
To set Auto Dial numbers, do the following:
1.
Using the up an down arrows, select Auto Dial.
2.
Tap PGM.
Phone#? displays.
3.
Tap the number keys.
The numbers scroll in the call waiting window.
NOTE: To insert a pause at any time, tap CLR 9 9. For example, you may have to insert a pause after dialing 9 to get
an outside line.
4.
Tap FWD (Do not tap PGM!).
A-Dial #1 displays (store auto dial number 1).
NOTE: To store a different auto dial number, using the up or down arrow keys, select the desired auto dial number.
5.
Tap PGM.
# <adial> saved displays .
6.
Select Save Cfg to store auto dial numbers.
Key Option Menu, Chime
Chime is used to add a chime tone to any key for incoming call announcement. The chime tone activates for approximately
five (5) seconds after a call is received.
To add the chime option to a key, do the following:
1.
Using the arrow keys, select Chime.
2.
Tap PGM.
3.
Tap the keys where you want to add a chime tone.
Both LEDs light red for the selected keys.
4.
Tap CLR to exit.
5.
Select Save Cfg to store Chime settings.
NOTE: The chime option continues on a key even if you change the key assignment.
To remove the chime option from a key, do the following:
1.
Using the arrow keys, select Chime.
2.
Tap PGM.
3.
Tap the keys where you want to remove a chime tone.
The red LEDs turn off for the selected keys.
4.
Tap CLR to exit.
5.
Select Save Cfg to store Chime settings.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
60 KP-32 Menu System
KP-32 Classic
Key Option Menu, Key Groups
Key Groups are used to assign one (1) key (the master key) to activate a group of keys simultaneously. Up to four (4) key
groups can be configured.
To configure a key group, do the following:
1.
Using the arrow keys, select Key Groups.
2.
Tap PGM.
Group 1 displays.
3.
Tap PGM.
Tap Master displays. The master key is the key you press to activate the group.
NOTE: You can tap PGM to bypass assigning a master key to the group, if you are planning to activate the group
with a local GPI input.
4.
Tap the intercom key dedicated as the master The master key must be a talk key. 
Both LEDs next to the key lights red. After you select the master key, Tap Slaves displays. Slave keys activate along
with the master key.
5.
Tap one (1) or more keys to select the slave keys.
You can make individual talk a listen keys slave by either tapping up or down on the key. You can tap a key again to
remove it from the key group.
6.
Tap CLR when finished.
Activating the master key causes it and all slave keys to activate. The LEDs for each key activate according to the
current key assignment for that key.
7.
Select Save Cfg to store Key Group settings.
NOTE: Key group settings continue on keys even if you change the key assignments.
Clearing a Key Group
To clear a key group, do the following:
1.
Using the arrow keys, select Key Groups.
2.
Tap PGM.
Group 1 displays.
3.
Tap PGM.
Tap Master displays.
4.
Tap the current master key.
The LEDs remain lit red. After you tap the master key, Tap Slaves displays.
5.
Tap all the keys where the LEDs are lit green.
This turns the LEDs off.
6.
Tap CLR when finished.
The key group is now cleared.
7.
Select Save Cfg to store the cleared key group setting.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
KP-32 Menu System 61
Key Option Menu, Solo
Solo is used to turn all other keys to turn off when activated. You can assign one (1) solo key.
To configure a solo key, do the following:
1.
Using the arrow keys, select Solo.
2.
Tap PGM.
Tap Key displays.
3.
Tap a key.
Both LEDs for the key lights red to confirm the assignment.
NOTE: Tap the key again if you made a mistake and want to remove the assignment.
4.
Tap CLR when finished.
Activating the solo key should now cause all other activated keys to turn off. The keys turn back on again when you
turn off the solo key.
5.
Select Save Cfg to store the Solo setting.
NOTE: The solo option continues on a key even if you change the key assignment.
To remove the solo key option, do the following:
1.
Using the arrow keys, select Solo.
1.
Tap PGM.
Tap Key displays. The LEDs for the solo key are lit red.
2.
Tap the solo key.
The LEDs turn off.
3.
Tap CLR to exit.
The solo key is now cleared.
4.
Select Save Cfg to save the change.
OMNEO Conn Menu (Available only with OKI Option Card Installed)
The OMNEO Conn menu is used to select an OMNEO connection to use with the keypanel.
To select an OMNEO connection, do the following:
1.
Using the arrow keys, select OMNEO Conn.
2.
Tap PGM.
A list of available OMNEO connections appears in a scrollable list.
3.
Using the arrow keys, scroll to the connection you want to use.
4.
Tap PGM.
5.
Tap CLR to exit.
The OMNEO Connection is set.
6.
Select Save Cfg to store the OMNEO Conn setting.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
62 KP-32 Menu System
KP-32 Classic
RVON Conn Menu (Available only with RVON Option Card Installed)
The RVON Conn. menu is used to select an RVON connection to use with the keypanel.
NOTE:
This menu item only appears when you have the RVON option installed and there are RVON devices available.
To select an RVON connection, do the following:
1.
Using the arrow keys, select RVON Conn.
2.
Tap PGM.
A list of available RVON connections appears in a scrollable list.
3.
Using the arrow keys, scroll to the connection you want to use.
4.
Tap PGM.
5.
Tap CLR to exit.
The RVON Connection is set.
6.
Select Save Cfg to store the RVON Conn. setting.
Service Menu
Service Menu, Aux Inputs (GPI Option Only)
Aux Inputs is enabled, the VOL SEL key can be used to select that source for volume adjustment. But even if a particular
AUX input is enabled, VOL SEL skips the input if it is not routed anywhere via the DSP mixing menu.
To enable or disable aux inputs, do the following:
1.
Select Aux Inputs, then tap PGM.
Aux In 1 displays.
2.
Using the arrow keys, select Aux In 1, Aux In 2, or Intercom.
3.
Tap PGM.
Enabled displays. The arrow  indicates that the input is enabled.
4.
Tap PGM.
5.
Tap CLR to exit.
The new Aux In assignment is now set.
6.
Select Save Cfg to store the Aux Inputs setting.
For more information, see “Mixing” on page 65.
Service Menu, Baud Rate
Baud Rate is used to select the baud rate at which the keypanel communicates with the intercom.
To set the baud rate, do the following:
1.
Select Baud Rate, then tap PGM.
Auto Baud displays.
2.
Using the arrow keys, select the baud rate you desire (Auto Baud, 9600 Baud, or 76.8K Baud).
The arrow  indicates that the option chosen.
3.
Tap PGM to select the baud rate.
4.
Tap CLR to exit.
The new baud rate is now set.
5.
Select Save Cfg to store the Baud Rate setting.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
KP-32 Menu System 63
Service Menu, Caller Vol.
Caller Vol. is used to enable or disable adjustments made to the crosspoint volume of the caller (rather than the overall
speaker/headset volume).
To disable/enable caller vol., do the following:
1.
Select Caller Vol.
Disable Adj appears. The arrow  indicates that caller vol. is disabled.
2.
Using the arrow keys, select Disable Adj or Enable Adj.
3.
Tap PGM.
Enable Adj or Disable Adj appears.
4.
Tap CLR to exit.
5.
Select Save Cfg to store the Caller Vol setting.
Service Menu, DIM
DIM is used to set the speaker or headphone level to diminish by a specified amount whenever a talk key is activated.
To set the DIM volume, do the following:
1.
Using the arrow keys, select DIM.
2.
Tap PGM.
Speaker displays.
3.
Using the arrow keys, select Headset.
4.
Tap PGM.
By default, -8dB displays for speaker, and 0 dB displays for headset. This is the default amount of dimming.
5.
Using the up arrow, increase the amount of dimming. 
OR
Using the down arrow decrease the amount of dimming.
6.
Tap CLR to exit.
The new dimming level is now set.
7.
Select Save Cfg to store the DIM setting.
Service Menu, Disply DIM
Disply DIM is used to adjust the alphanumeric display settings.
To adjust the display DIM, do the following:
1.
Using the arrow keys, select Display DIM.
2.
Tap PGM.
Disply Off displays.
3.
Using the arrow keys, select any of the following:
DIM:
Possibly a better choice when the ambient light level is low. Uses less power and increases display life.
Norm:
Default medium brightness setting.
Minimum:
Good when ambient light is bright.
Maximum: Recommended only for very bright ambient light, such as outdoors. Uses maximum power and
decreases display life.
NOTE: For settings which change the operating brightness, run “Service Menu, Save Cfg” on page 73, to store the
setting.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
64 KP-32 Menu System
KP-32 Classic
Service Menu, DSP Func
The DSP Func menu is used to access the digital signal processing features.
To access the DSP functions, do the following:
1.
Using the arrow keys, select DSP Func.
2.
Tap PGM.
Filters displays.
3.
Using the arrow keys, select the type of DSP function desired.
Filters
Gating
Metering
Mixing
Refer to one (1) of the following paragraphs for further information on the item that you select.
Filters
Filters allows you to add a 9.6kHz notch filter to one (1) or more audio sources. This can be useful in a few cases when the
keypanel data port signal is being heard in the audio line due to cable routing problems.
To adjust the filters, do the following:
1.
Select Filters.
2.
Tap PGM.
Mic displays.
3.
Using the arrow keys, select the audio source you want to modify.
Mic
Matrix
Aux 1
Aux 2
4.
Tap PGM.
None displays to indicate that no filters is selected.
5.
Tap the up arrow key.
Notch displays.
6.
Tap PGM.
Notch displays. The arrow indicates notch filter is now selected.
7.
Tap CLR to exit.
8.
Select Save Cfg to save the change.
Gating
Gating minimizes or eliminates background noise problems by shutting off an audio source when the sound level drops below
a certain threshold.
To select the audio source for gating, do the following:
1.
Select Gating.
2.
Tap PGM.
Mic displays.
3.
Using the arrow keys, select an audio source.
Mic
Matrix
Aux 1
Aux 2
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
KP-32 Menu System 65
4.
Tap PGM.
Gating displays.
5.
Tap PGM.
Gating displays. The arrow indicates that gating is now selected.
6.
Tap CLR to exit.
7.
Select Save Cfg to save the change.
Metering
Metering lets you use the Vol. display as an LED bar graph meter to monitor an audio source for about one (1) minute.
To select the audio source for metering, do the following:
1.
Select Metering.
2.
Tap PGM. 
Mic displays.
3.
Using the arrow keys, select an audio source.
Mic
Matrix
Aux 1
4.
Aux 2
Tap PGM.
The Vol. bar graph is now monitoring the selected audio source.
5.
Tap CLR to exit metering, or allow the metering function to timeout after about one (1) minute.
Mixing
Mixing lets you route selected audio signals to the intercom system, to the speaker, or to the left or right headphone when
using a headset. By default, the microphone signal is routed to the matrix. The matrix signal is routed to the speaker and to the
left and right headphones.
1.
Select Mixing.
2.
Tap PGM.
To Matrix displays.
3.
Using the arrow keys, select the audio mixing destination.
To Matrix
Speaker
Left Hdst
Right Hdst
4.
Tap PGM.
Mic or Mic displays. If an arrow displays, this indicates that the mic signal is currently being routed to the
destination that you selected in step 2. To toggle the selection, press PGM. You can also press or to display
and toggle any of the following items:
Mic
Matrix
Aux 1
Aux 2
5.
Tap CLR to exit.
6.
Select Save Cfg to store any mixing changes.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
66 KP-32 Menu System
KP-32 Classic
Service Menu, Hdst Sel
Hdst Sel is used to select either the front panel headset jack or the headset connector on the optional rear connector module.
By default, the front panel jack is selected.
To select the headset connection, do the following
1.
Using the arrow keys, select Hdst Sel.
2.
Tap PGM.
Default displays. The arrow indicates the default front panel jack is selected.
3.
Using the up or down arrow, select either Default or External.
4.
Tap PGM.
5.
Tap CLR to exit.
6.
Select Save Cfg to store the new Hdst Sel setting.
Service Menu, LCP-32
By default, each LCP-32 you connect to the KP-32 takes control of level adjustment for the first available group of 16 physical
keys found. The first LCP-32 adjusts keys 1-16, which corresponds to the bottom row of keys on the KP-32; the second
LCP-32 adjusts keys 17-32, and so forth. If you do not want to use an LCP-32 with certain keys, you must program the 
KP-32 to skip those keys.
FIGURE 11.
LCP-32 correspondence to KP-32 and EKP-32
For example, you may not want to use LCP-32s with the KP-32 but do want to use them with an EKP-32. In this case, you
must turn off LCP usage for keys 1-32 as follows:
To configure the LCP-32 setup, do the following:
1.
Using the arrow keys, select LCP-32.
2.
Tap PGM.
1-16: Yes displays. This indicates that the first connected LCP-32 attaches to keys 1-16.
3.
Tap PGM.
1-16: Skip displays. This indicates that the first connected LCP-32 skips keys 1-16 and attaches to the next available
row of keys.
4.
Using the arrow keys keys, select 17-32: Yes.
5.
Tap PGM.
17-32:Skip displays. This indicates that the first connected LCP-32 skips keys 17-32 and attaches to the next
available row of keys.
6.
Tap CLR to exit.
7.
Select Save Cfg to store the new LCP-32 settings.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
KP-32 Menu System 67
Service Menu, Local GPIO
If your KP-32 has an optional Connector Module, you can use this menu item to assign the GPIO inputs and outputs. Inputs
can be assigned to activate intercom keys (including group master keys and a solo key). Outputs can be activated by intercom
keys. Set up inputs and outputs as follows:
Assigning an Input to Activate a Key
To assign an input to activate a key, do the following:
1.
Using the arrow keys, select Local GPIO.
2.
Tap PGM.
Input displays.
3.
Tap PGM.
GPI Inp #1 displays.
4.
Using the arrow keys, select a different GPI input.
5.
Tap PGM.
6.
Use the up arrow key to select Talk Key.
7.
Tap PGM.
Tap Key displays.
8.
Tap the intercom key you want to assign.
This is the key activated when the GPI input activates.
9.
Tap CLR to exit.
OR
Tap BACK to back up and make more assignments.
10.
Select Save Cfg to store local GPIO settings.
Assigning an Input to Activate a Key Group
To assign an input to activate a key group, do the following:
1.
Using the arrow keys, select Local GPIO.
2.
Tap PGM.
Input displays.
3.
Tap PGM.
GPI Inp #1 displays.
4.
Using the arrow keys, select a different GPI input.
5.
Tap PGM.
6.
Use the up arrow key to select Group.
7.
Tap PGM.
By default, Group 1 displays. Use the up or down arrow keys to display a different group.
8.
Tap PGM.
An arrow appears to indicate that the group is now selected. For example, if you press PGM to select Group 1,
Group 1 displays.
9.
Tap CLR to exit.
OR
Tap BACK to back up and make more assignments.
10.
Select Save Cfg to store local GPIO settings.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
68 KP-32 Menu System
KP-32 Classic
Removing an Input Assignment
To remove an input assignment, do the following:
1.
Using the arrow keys, select GPIO.
2.
Tap PGM.
3.
Using the arrow keys, select Input.
4.
Tap PGM.
5.
Using the arrow keys, select the GPI input you want to remove.
6.
Tap PGM.
7.
Use the up arrow key to select Not Asgnd.
8.
Tap PGM.
 Not Asgnd displays. The arrow indicates that Not Assigned is the new selection.
9.
Tap CLR to exit.
10.
Select Save Cfg to store local GPIO settings.
Adding or Removing a GPI Output Key Assignment
To add or remove a GPI output key assignment, do the following:
1.
Select Local GPIO
2.
Tap PGM.
Input displays.
3.
Use the up arrow to select Output.
4.
Tap PGM.
GPI Out #1 displays.
5.
Using the arrow keys, select a different GPI output.
6.
Tap PGM.
Tap Key displays. Also, if there is a key currently assigned to activate the selected GPI output, both LEDs for that key
light red. If there is no assignment, no LEDs are lit red.
7.
Tap an intercom key to add or remove the GPI output assignment.
8.
Tap CLR to exit.
OR
Tap BACK to back up and make more assignments.
9.
Select Save Cfg to store local GPIO settings.
Service Menu, Matrix Out
This menu item allows the user to select between Normal or Hot Mic. In the Normal (default) setting audio from the Mic goes
out to the Matrix when the talk key is latched. In the Hot Mic setting audio from the Mic goes out to the Matrix without regard
to the talk key’s state.
To select where the audio is routed, do the following:
1.
Select Matrix Out.
2.
Tap PGM.
Normal displays.
3.
Use the up arrow keys, select either Normal or Hot Mic.
4.
Tap PGM.
5.
Tap CLR to exit.
6.
Select Save Cfg to store Matrix Out settings.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
KP-32 Menu System 69
Service Menu, Mic Select
This menu item allows the user to select between the Panel and Headset Mic. In the Normal (default) setting, audio from the
Panel Mic used. In the Hdst Only, setting audio from the Headset Mic is used.This is used to force the use of the headset
microphone even when the keypanel’s speaker is being used.
To select the mic you want to use, do the following:
1.
Using the arrow keys, select Mic Select.
2.
Tap PGM.
Normal displays.
3.
Use the up arrow key to select either Normal or Hdst Only.
4.
Tap PGM.
5.
Tap CLR to exit.
6.
Select Save Cfg to store Mic Select settings.
Service Menu, Min Volume
This menu item allows the user to set the minimum volume level for both the keypanel speaker and the headset speaker(s).
This is the minimum volume level available on the volume control located on the front panel of the KP-32.
To set the minimum volume for the speaker or headset, do the following:
1.
Select Min Volume.
2.
Tap PGM.
Speaker displays.
3.
Use the up arrow key to select either Speaker or Headset.
4.
Tap PGM
5.
Using the arrow keys, increase or decrease the minimum volume level.
The range is -1dB to -60dB or Full Mute.
6.
Tap PGM.
7.
Tap CLR to exit.
8.
Select Save Cfg to store Min Volume settings.
Service Menu, Mod Assign
NOTE:
Normally, this is a service adjustment that is required only when replacing a key and display module. It may also
be required if for some reason, the key assignments, as displayed in AZedit, appear to be in the wrong positions
on the keypanel or expansion panel.
The KP-32 and EKP-32 use module ID numbers (Mod ID numbers) to define the address of each key and display module.Mod
1 is always assigned to the right half of the KP-32 and this never changes, since this module has the keypad and is unique.
However, the rest of the modules are identical. When replacing any of these modules, you may have to reset the Mod ID
number as follows:
To assign modules for a system with EKP units, do the following:
1.
Select Mod Assign.
2.
Tap PGM.
Cancel? displays.
3.
Tap PGM to exit the procedure without making changes
All of the alphanumeric displays, except Mod 1 appear.
4.
Assign the Mod IDs as shown in the figure.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
70 KP-32 Menu System
5.
KP-32 Classic
Repeat the procedure for each module.
NOTE: You do not need to run Save Cfg after changing Mod assignments.
Service Menu, OMNEO Setup (OKI Option Card Only)
The OMNEO Setup menu is used to configure the OKI’s device name, enable DHCP, and address the OKI option card for the
KP-32.
IMPORTANT:
When making changes to the OKI device name and the IP Address at the keypanel, you must make the
same changes in AZedit or IPedit before the connection is made. For example, you configure all your
devices in AZedit or IPedit before putting the matrix on the network. Once the keypanels have been
configured and the matrix is put on the network, the connections are automatically made. Making
changes at the keypanel alone does not automatically update the configuration on the matrix.
To configure the OMNEO device name, do the following:
1.
Using the arrow keys, select OMNEO Setup.
2.
Tap PGM.
Device Name appears.
3.
Tap PGM.
The OMNEO device name appears with the first character blinking.
4.
Using the arrows, scroll to the to the first character of the device name desired.
5.
Tap PGM.
The focus moves to the next character in the device name.
NOTE: You can also use the volume control to move the cursor position to the left and right.
6.
Repeat steps 4 and 5 until the OMNEO Device is named.
7.
When finished entering the OMNEO device name, press FWD.
The OMNEO device is named.
NOTE:
CLR deletes the current character. 0 can be used to insert a character at the current position. Scroll up/scroll down
can also be used to move the current cursor position.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
KP-32 Menu System 71
To select the type of addressing for the OMNEO device, do the following:
1.
Using the arrow keys, select OMNEO Setup.
2.
Tap PGM.
Device Name appears.
3.
Using the arrow keys, scroll to DHCP.
4.
Tap PGM.
The type of addressing appears with an arrow denoting which is selected.
5.
Using the arrow keys, select either Use DHCP or Fixed IP.
6.
Tap PGM.
The addressing type is set.
To configure the IP Parameters for the OMNEO device, do the following:
IMPORTANT:
To make changes to the IP Address from the keypanel, you must set the type of addressing to Fixed IP.
1.
Using the arrow keys, select OMNEO Setup.
2.
Tap PGM.
Device Name appears.
3.
Using the arrow keys, scroll to IP Params.
4.
Tap PGM.
IP Address appears in the keypanel display.
5.
Tap PGM.
The IP Address octet appears in the keypanel display with the first octet blinking.
6.
Using the keypad, enter the IP Address.
Use the PGM key as the dots between octets.
7.
When finished entering the IP Address, tap PGM.
Netmask appears in the keypanel display.
8.
Tap PGM.
The Netmask octet appears in the keypanel display with the first octet blinking.
9.
Using the keypad, enter the Netmask, if necessary.
Use the PGM key as the dots between octets.
10.
When finished entering the Netmask, tap PGM.
Gateway appears in the keypanel display.
11.
Using the keypad, enter the Gateway, if necessary.
Use the PGM key as the dots between octets.
12.
When finished entering the Gateway, tap PGM.
The DNS Srv 1 appears in the keypanel display.
13.
Using the keypad, enter the DNS Svr 1 address, if necessary.
Use the PGM key as the dots between octets.
14.
When finished entering the DNS Svr 1 address, tap PGM.
DNS Srv 2 appears in the keypanel display.
15.
Tap PGM.
The DNS Server 2 address appears in the keypanel display with the first octet blinking.
16.
Using the keypad, enter the DNS Svr 2 address, if necessary.
17.
When finished entering the DNS Svr 2 address, tap PGM.
Domain Name appears in the keypanel display.
18.
Tap PGM.
The Domain name appears in the keypanel display with the first character blinking.
19.
Using the arrows, scroll to the to the first character of the device name desired.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
72 KP-32 Menu System
20.
KP-32 Classic
Tap PGM.
The focus moves to the next character in the device name.
NOTE: You can also use the volume control to move the cursor position to the left and right.
21.
Repeat steps 19 and 20 until the Domain Name is entered.
NOTE: CLR deletes the current character. 0 can be used to insert a character at the current position. Scroll up/scroll
down can also be used to move the current cursor position.
22.
Tap FWD to exit.
23.
Select Save Cfg to store the OMNEO Setup settings.
Service Menu, Output Level
Allows the adjustment of the nominal audio output level to the matrix from 0 dBu to +8dBu.
To configure the output level, do the following:
1.
Select Outp Level.
2.
Tap PGM.
+8dB displays. The down arrow decreases the level or the up arrow increases the level.
3.
Tap PGM.
4.
Tap CLR to exit.
5.
Select Save Cfg to store the Output Level settings.
Service Menu, Preamp Out (GPI Option Only)
Allows the user to choose how audio is routed to the Preamp Output connector. When Switched is chosen, keypanel audio is
routed to the preamp output connector when a talk key is latched. When Hot Mic is chosen, audio is always available at the
preamp output connector. When Disabled is chosen, keypanel audio is isolated from the preamp output connector.
To configure Preamp Out, do the following:
1.
Select Preamp Out.
2.
Tap PGM.
Switched displays or up arrows toggle between Switched, Hot Mic, and Disabled.
3.
Tap PGM.
4.
Tap CLR to exit.
5.
Select Save Cfg to store the Preamp Out settings.
Service Menu, Reset Cfg
Reset Cfg restores all custom settings to the defaults and erases all stored autodial numbers. Select Save Cfg to save the
settings.
Service Menu, RVON Setup (RVON Option Card Only)
RVON Setup is used to configure the IP Address, Netmask Address, and Gateway Address for the RVON device you want to
use.
To configure the RVON device, do the following:
1.
Select RVON Setup.
2.
Tap PGM.
IP Address appears.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
KP-32 Menu System 73
3.
Tap PGM.
The enter IP Address window appears.
4.
Using the keypad, enter the IP Address.
Use the PGM button as the dots between octets.
5.
When finished entering the IP Address, press PGM.
Netmask appears in the keypanel display.
6.
Using the keypad, enter the Netmask, if necessary.
Use the PGM button as the dots between octets.
7.
When finished entering the Netmask, press PGM.
Gateway appear in the keypanel display.
8.
Using the keypad, enter the Gateway, if necessary.
Use the PGM button as the dots between octets.
9.
When finished entering the Gateway, press PGM.
The RVON Setup menu appears in the keypanel display.
10.
Tap CLR to exit.
11.
Select Save Cfg to store the RVON Setup settings.
Service Menu, Save Cfg
Save Cfg saves custom settings that you have made in the Key Option or Service menus. After customizing settings in the Key
Option and Service menus, run Save Cfg to store your custom settings in non-volatile memory. This assures protection of you
settings when the keypanel is powered down. To erase all custom settings, run Service Menu, Reset Cfg.
Service Menu, Scr Saver
The Scr Saver menu item is used to configure the operation of the screen saver on the keypanel.
The following options are available to configure the screen saver:
Delay -
By default, a one (1) hour delay is programmed. You can choose 30 min and 1 to 12 hours (available in
one (1) hour increments).
Display Off -
Display Off turns the display off without displaying the screen saver. Press any key to activate the
display window.
Activate -
When selected, Activate enables the screen saver immediately. Press any key to activate the display
window.
Service Menu, Sidetone
Sidetone is used to adjust the level of your own voice heard in the headphones when using a headset. Most people prefer some
amount of sidetone to overcome the muffled sensation when talking, especially when wearing a full-muff headset. The
maximum level is 0dB.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
74 KP-32 Menu System
KP-32 Classic
Service Menu, Snoop Tally
Snoop Tallies provide an indication to keypanel users that someone is listening to them.
NOTE:
To use Snoop Tallies, the keypanel must be working in HOT MIC (USM) mode. This is available only on the 
KP-32 and the KP CLD panels. And, they must be enabled in the intercom (Options|Intercom
Configuration|Options|Generate Snoop Tallies).
To configure snoop tally, do the following:
1.
Select Snoop Tally.
2.
Tap PGM.
➔ No Chime (Default) appears in the display window. Up arrows toggle between No Chime and Chime.
3.
Tap PGM.
Snoop Tally is configured.
4.
Tap CLR to exit.
5.
Select Save Cfg to store the Snoop Tally settings.
Service Menu, Test Panel
Test Panel PGM lets you check the operation of all keys and displays.
All alpha-numeric displays show a % symbol. Pressing down on any key (except the Headset / Vol. Sel. key) causes OK to
display. This verifies operation of the key. Tapping up or down on the Headset / Vol. Sel. key causes the display to cycle
through the available selections.
If latching is enabled, tapping up or down on any intercom key, or the call waiting key, causes the corresponding red LED to
light. This verifies latching operation and also that the each red LED is OK.
Holding any key in the up or down position causes the corresponding green LED to light. This verifies operation of the green
LEDs.
Tapping any keypad button (except CLR) causes the keypad button name to appear in the call waiting window. This verifies
operation of the keypad buttons.
Service Menu, Tone Gen
Tone Generator PGM turns the KP-32 tone generator on or off. You can use the tone generator to check the audio path from
the keypanel to the matrix and back.
NOTE:
The microphone is muted when the tone generator is active.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
CHAPTER 7
Specifications
Microphone Preamplifier
Electret Mic Input Level @ 1kHz: .............................................................................................................................-42dB, 150
Dynamic Mic Input Level @ 1kHz:........................................................................................................................-50dBm, 150
Default Output Level (to matrix): ............................................................................................................................. 0dBu, +8dBu
Max Voltage Gain, Mic to Line: ................................................................................................................................ 70dB, ± 2dB
Frequency Response: ................................................................................................................................100Hz to 10kHz, ± 2dB
Limiter:.............................................................................................................................................................8dB above nominal
Tone Generator
Output Level (to matrix): ........................................................................................................................................ +8dBu ± 2dBu
Output Frequency:................................................................................................................................................................ 500Hz
Headphone Amplifier
Maximum Voltage Gain:...................................................................................................................................................... 200dB
Frequency Response: ................................................................................................................................100Hz to 10kHz, ± 2dB
Headphone Impedance: ...................................................................................................................................................8 to 600
Output Power: ............................................................................................................................................................1W into 50
Output Voltage Level:........................................................................................................................8 Volts peak-to-peak (max.)
Sidetone Range: ..................................................................................................................................................................... 25dB
Speaker Amplifier and Speaker
Frequency Response: ................................................................................................................................100Hz to 10kHz, ± 2dB
Output Power (per amplifier): ......................................................................................................................................4W into 4
Output Voltage Level:.......................................................................................................................12 Volts peak-to-peak (max)
Volume Control Range: ......................................................................................................................................................... 30dB
Speaker Rating: ...............................................................................................................................................................4W (max)
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
76 Specifications
KP-32 Classic
Intercom Input/Output
Input:
Default Nominal: +8dBu. Peak: ± 20dBu max.
Output:
+8dBu, ± 2dBu nominal
External Line Input: (Program Input)
Input Level:
+8dBu nominal
General
AC Supply:
External, switching type, 100-240VAC, 50/60Hz with locking DIN connector for attachment to the keypanel and universal
IEC connector for connection to various AC mains cords.
Environmental:
Storage:
-40°C (-40°F) to +60°C (140°F)
Operating:
-10°C (14°F) to +41°C (105.8°F)
Dimensions:
19" (48.26cm) wide x 2RU x 3.5" (8.89cm) deep
Approvals:
UL, CSA, VDE, CE
Connectors (Other connector options available)
Panel Microphone Connector
Type: 3-circuit, 1/4" phone jack w/threaded metal bushing, compatible with RTS MCP5/6
Pin-out:
Tip:
+Audio and DC bias
Ring:
Common
Sleeve:
Chassis ground
Headset Connector
Type:
XLR5 female
Pin-out:
Pin 1:
Mic low
Pin 2:
Mic high
Pin 3:
Common
Pin 4:
Headphone left high
Pin 5:
Headphone right high
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
Specifications 77
Power Input Connector
Type:
5-pin locking DIN
Pin-out:
Pin1:
Common
Pin2:
Common
Pin3:
+5VDC, 1.50A (max)
Pin4:
-15VDC, 0.150A (max)
Pin5:
+15VDC, 0.5A (max)
Intercom Connectors: Parallel-wired DE9S and RJ12 Connectors
Type:
DE9S
Pin-out:
Pin 1:
Data +
Pin 2:
Data -
Pin 3:
Audio in (from matrix) shield
Pin 4:
Audio out (to matrix) +
Pin 5:
Audio out (to matrix) -
Pin 6:
Data shield
Pin 7:
Audio in (from matrix) -
Pin 8:
Audio in (from matrix) +
Pin 9:
Audio out (to matrix) shield
Type:
RJ12
Pin-out:
Pin 1:
Data -
Pin 2:
Audio in (from matrix) +
Pin 3:
Audio out (to matrix) +
Pin 4:
Audio out (to matrix) -
Pin 5:
Audio in (from matrix) -
Pin 6:
Data +
Expansion Connector
Type:
RJ45
LCP Connector
Type:
RJ45
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
78 Specifications
KP-32 Classic
GPI Module Connectors (Optional)
Aux 1 In (Auxiliary program input 1)
Type:
3-pin female XLR
Pin-out:
Pin 1:
Ground
Pin 2:
Input +
Pin 3:
Input -
NOTE:
Balanced input, +8dBu nominal.
Aux 2 In (Auxiliary program input 2)
Type:
3-pin female XLR
Pin-out:
Pin 1:
Ground
Pin 2:
Input +
Pin 3:
Input -
NOTE:
Balanced input, +8dBu nominal.
Relay 1 & 2 Out
Type:
9-pin male D-Sub
Pin-out:
Pin 1:
NC contact 1
Pin 2:
COM contact 1
Pin 3:
NO contact 1
Pin 4:
NC contact 2
Pin 5:
COM contact 2
Pin 6:
NO contact 2
Pin 7:
+5VDC
Pin 8:
Ground
Pin 9:
+5VDC
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
Specifications 79
Relay 3 & 4 Out
Type:
9-pin male D-Sub
Pin-out:
Pin 1:
NC contact 3
Pin 2:
COM contact 3
Pin 3:
NO contact 3
Pin 4:
NC contact 4
Pin 5:
COM contact 4
Pin 6:
NO contact 4
Pin 7:
+5VDC
Pin 8:
Ground
Pin 9:
+5VDC
NOTE:
The relay 1 and 2 contacts are electrically separate, but operate in unison. The relay 3 and 4 contacts are
electrically separate, but operate in unison. The +5VDC pins are connected internally through 1K resistors to
+5VDC and can source 5mA. This voltage can be used with the relay contacts to create an active high output for
some devices that require a +5VDC signal to activate. For example, connecting pin 7 to pin 3 of the Relay 1 and
2 connector results in +5VDC on pin 2 when the relay is activated.
Opto 1-4 In (Opto-isolated control inputs)
Type:
9-pin male D-Sub
Pin-out:
Pin 1:
Input 1 Gnd
Pin 2:
Input 2 Gnd
Pin 3:
Input 3 Gnd
Pin 4:
Input 4 Gnd
Pin 5:
Gnd
Pin 6:
Switch contact input 1
Pin 7:
Switch contact input 2
Pin 8:
Switch contact input 3
Pin 9:
Switch contact input 4
NOTE:
A contact closure between any switch input and ground activates that input. The switch contact inputs are also
connected internally through 1K resistors to internal +5VDC and can source 5mA for use with an external
transistor switch circuit.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
80 Specifications
KP-32 Classic
OC 1 & 2 Out (J2)
Type:
9-pin male D-Sub
Pin-out:
Pin 1:
Gnd OC1
Pin 2:
Emitter OC1
Pin 3:
Collector OC1
Pin 4:
Gnd OC2
Pin 5:
Emitter OC2
Pin 6:
Collector OC2
Pin 7:
5VDC
Pin 8:
No connection
Pin 9:
5VDC
Headset (External headset connector)
Type:
9-pin male D-Sub
Pin-out:
Pin 1:
Gnd
Pin 2:
N/A leave unconnected
Pin 3:
N/A leave unconnected
Pin 4:
N/A leave unconnected
Pin 5:
Balanced dynamic mic input +
Pin 6:
Gnd
Pin 7:
Headset Listen Out Left
Pin 8:
Headset Listen Out Right
Pin 9:
Balanced dynamic mic input -
NOTE:
Mic input -50dBu nominal. Headset out 0.325W into 8
Foot Switch/Speaker
Type:
9-pin male D-Sub
Pin-out:
Pin 1:
Gnd
Pin 2:
Speaker Minus (-)
Pin 3:
Gnd
Pin 4:
No connection
Pin 5:
Foot Switch
Pin 6:
Speaker Plus (+)
Pin 7:
No connection
Pin 8:
No connection
Pin 9:
Gnd
NOTE:
A switch contact closure from the footswitch input to ground activates the footswitch input.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
Specifications 81
MIC In (J7) Unbalanced Panel Microphone Input
Type:
3-pin female XLR
Pin-Out:
Pin 1:
Shield (circuit common)
Pin 2:
DC bias and Audio Plus (+)
Pin 3:
GND
NOTE:
Input level -42.5dBu nominal.
MIC Out (J8) Balanced Microphone Output
Type:
3-pin male XLR
Pin-out:
Pin 1:
Shield (circuit common)
Pin 2:
Audio output +
Pin 3:
Audio output -
NOTE:
Output level +8dBu nominal (balanced).
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
82 Specifications
Bosch Security Systems, Inc.
KP-32 Classic
User Manual
F.01U.193.253
Rev. 21
CHAPTER 8
KP9X Keypad Sequence Quick Reference
KP9X Display Sequences
FUNC DISPLAY 0
Diagnostics mode.
FUNC DISPLAY 1
Display port number.
FUNC DISPLAY 2
Display level 2 talk assignments.
FUNC DISPLAY 3
Display listen assignments.
FUNC DISPLAY 8
Display setup page assignments.
FUNC DISPLAY
Up and down arrows select items as follows:
ID:
Display the calculated port number.
Lev2:
Display level 2 talk assignments.
Lstn:
Display listen assignments.
Name:
Display crosspoints closed to this keypanel.
Type:
Display level 1 talk key assignment types.
Mtx:
Display matrix ID for all level 1 talk assignments.
Tone:
Turn on tone generator.
Epnl:
Display setup page assignments. Mn=KP-32 bottom row keys. X1=KP-32 top row key.
X2=EKP-32 bottom row keys. X3=EKP-32 top row keys.
Gain:
Port / party line listen gain. Turn on listen key. Arrow keys to change gain.
VRst:
Reset all port / party line gains to 0 dB.
Asgn:
Display key assignments that are not currently accessible.
Test:
Test keys and displays.
Vxxx:
Display keypanel firmware version.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
84 KP9X Keypad Sequence Quick Reference
KP-32 Classic
KP9X Setup Page Assignment
1.
Tap E-PNL.
2.
Select a setup page: tap 1, or 2, etc.
3.
Tap PGM.
4.
Tap any key in the row to assign the selected setup page to that row of keys.
Key Assignments Using Keypad Numeric Entry
1.
For talk level 2 assignment only: Tap 0 0.
2.
Select the key assignment type:
NUM Intercom port.
PL Party line.
AUTO Auto function.
FUNC SLIST Special list.
FUNC IFB IFB.
FUNC ISO Camera ISO.
FUNC RELAY Relay or GPI output.
3.
Auto function assignment only: Tap an additional number to select the desired auto function:
1 Auto listen
2 Auto follow
3 Auto mute
4 Auto reciprocal
5 All call
6 DIM (talk level 2 only, for point-to-point key)
7 Auto table (use only with IFB)
4.
Trunked intercoms only: Select an intercom matrix (tap 1, or 2 etc.).
5.
Tap one (1) or more number keys to select the desired port number, party line number, etc.:
6.
If the destination is in a remote matrix, you must always enter three (3) digits for port numbers and two (2) digits
for the function number.
7.
Tap PGM.
8.
Tap down on a key to assign talk.
OR
Tap up to assign listen.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
KP9X Keypad Sequence Quick Reference 85
KP9X Phone Operation
KP9X Hang-up Sequence
1.
Turn off the TIF talk key.
2.
On the keypad, tap PHONE-CLR.
3.
Turn the TIF talk key on, then off. 
The TIF key talk and listen indicators turn off and the TIF hangs up.
KP9X Dial Sequence
1.
Activate the TIF listen key (listen LED green).
Make sure the TIF talk key is off (Talk LED off).
2.
On the keypad, tap CLR-PHONE-PGM.
3.
Activate the TIF talk key (talk LED turns green). 
The on LED at the TIF activates, and you should hear dial tone at the KP-32.
4.
Dial the telephone number.
Digits scroll in the display above the TIF talk key. When the far end answers, you can dial additional digits (to access
a mail system or automated response system, etc.). When finished dialing, momentarily turn off the TIF talk key to
end dialing mode (talk LED turns red).
5.
Turn the TIF talk key on for conversation.
KP9X Redial Sequence
1.
Tap the PHONE key to activate dialing mode.
2.
Tap up on the TIF key to activate listen.
3.
Tap CLR 0 0. 
The last phone number is redialed.
4.
After the number has dialed, click the PHONE key to end dialing mode.
If the far end answers, tap down on the TIF key to activate talk.
5.
Use the KP9X hang-up sequence to hang up.
KP9X Autodial Sequences
Storing an Autodial Number in the TIF
1.
Tap the PHONE key.
2.
Tap the TIF talk key to latch it on.
3.
Using the keypad, dial the phone number you want to store.
The entire phone number sequence can have up to 30 digits.
NOTE: To insert one (1) or more pauses anywhere in the dialing sequence, enter CLR CLR 9 9 for each pause.
4.
After dialing the telephone number, click CLR PGM, then enter a 2-digit number (01, 02, etc. up to 32) you want to
use as the autodial number.
5.
After storing the autodial number, hang up using the KP9X hang-up sequence.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
86 KP9X Keypad Sequence Quick Reference
KP-32 Classic
Dialing an Autodial Number Stored in the TIF
1.
Tap the PHONE key to activate dialing mode.
2.
Tap down on the TIF talk key to latch it in the on position.
3.
Tap CLR followed by the autodial number (01, 02, etc.).
4.
When finished dialing, click the PHONE key again to exit dialing mode.
5.
Hang up using the KP9X hang-up sequence.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
CHAPTER 9
KP-32 Menu System Quick Reference
Menu Access
1.
Clear all entries from the call waiting display (if not clear) by tapping up one (1) or more times on the call waiting
key.
2.
Tap MENU to activate the menu system.
3.
Press the down arrow key to scroll forward through the list of menus. Press the up arrow key to scroll back.
4.
Tap FWD or PGM to enter a menu. Tap BACK to exit a menu.
5.
Within a menu:
•
•
•
Press the arrow keys to scroll.
Tap FWD or PGM to select an item.
Tap BACK to cancel a selection or to go back to the previous menu level.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
88 KP-32 Menu System Quick Reference
KP-32 Classic
Menu List
Display Menu
Asgn Type
Chans On
Key Groups
Key List
Level 2
Listen
Matrix
Panel ID
Version
Key Assign Menu
Matrix
Pt-to-Pt
Party Line
IFB
Spcl List
Sys Relay
Camera ISO
UPL
IFSL
Auto Func
Key Gain
Reset Vols
Setup Page
Key Options
Menu
Auto Diala
Chimea
Key Groupsa
Soloa
RVON Conn.
list of RVON Offersa
Or
list of OMNEO Connections
Save Cfg.
Service Menu
Alphas
Aux Inputsa
Baud Ratea
Caller Vol.a
DIMa
Displ DIMa
DSP Funca
Hdst Seta
LCP-32a
Local GPIOa
Matrix Outa
Mic Selecta
Min Volumea
Mod Assigna
Outp Levela
Preamp Outa
Reset Cfga
RVON or OMNEO Setupa
Save Cfg
Scr Savera
Sidetonea
Snoop Tallya
Test Panel
Tone Gen
a. Run Save Cfg (see “Service Menu, Save Cfg” on page 73) to save these settings.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
CHAPTER 10
Mode 2 Operation
Section 2
Switch 4: Call Flash Timeout*
When the switch is closed the menu and indefinite talking is disabled.
NOTE:
The * represents the default position.
Section 3
LED Indications for Intercom Keys
Talk LED Indications
The talk LED is the lower LED for each key. The talk LED indications are as follows:
Continuous Red*
Talk is on and the keypanel operator can be heard at the destination.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
90 Mode 2 Operation
KP-32 Classic
Flashing Display Alpha (In-use)*
The key is off, but someone is talking to the destination. This indication is provided for any local PL, IFB, ISO, or TIF key. If
you activate the key, either of two (2) things happen:
•
If you activate the key and the talk LED turns continuous red, this indicates that you and the other
keypanel operator are both talking to the destination.
•
IFB keys only: If the alpha alternates between the normal display and ** when an IFB key is activated,
this indicates that the other keypanel has a higher IFB priority and you cannot talk at this time.
•
The slow tally alpha display in-use indication for TIF keys can be disabled in AZedit:
Solid Red Talk LED & Flashing Display Alternating Pattern of Alpha & (**) (Busy)
You cannot talk at this time. This indication occurs when you activate a local or remote IFB key that is already in-use by a
keypanel with a higher IFB priority. It also occurs when you activate any key assigned to a remote destination, but there are
currently no trunks available.
Flashing Display Alpha (on time equal to off time)
There is an incoming call from the destination assigned to the key. Activate the key to talk back.
NOTE:
The duration of incoming call flash is controlled by DIP switch 4 on the KP-32 back panel. See “Telephone
Operation” on page 37, for further information.
Amber Talk LED
This indicates that a key is ready to talk (key is on), but requires external footswitch activation to talk.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
CHAPTER 11
Glossary
All Call. For talk key assignment only. Activating an All Call key also activates all talk keys to the left of the All Call key (up
to, but not including another All Call key).
Alpha. Alphas are the user-configurable names which identify destinations (intercom ports, party lines, etc.). Change Alpha
names for intercom ports using the Port Alpha button in AZedit. Change Alpha names for everything else using the Other
Alpha button. When you assign a destination to a talk key, the alpha name appears in the alphanumeric display for that key.
Auto Follow (AF). A key assignment for listen keys only. Auto follow causes a key's listen assignment to track the talk
assignment. Thus, if you change the talk assignment, you do not also have to change the listen assignment. You can manually
activate an auto-follow listen key independently of the talk key. If you want auto-activation (or deactivation) of listen during
talk, use one of the other auto key assignments, such as auto listen or auto mute.
Auto Listen (AL). A key assignment for listen keys only. This assignment works like auto follow, except that listen
automatically activates during talk. Auto listen is a good assignment for use with party lines, TIFs, or other non-keypanel
devices that do not have talk-back control of matrix crosspoints.
Auto Mute (AM). A key assignment for listen keys only. This assignment works like auto follow, except that listen
automatically mutes during talk. Auto mute can help prevent feedback or echo when talking to certain destinations. In some
cases, you may find it works better to disable talk latching for this type of key, because if you accidentally leave talk latched on
you are not able to hear the destination.
Auto Reciprocal (AR)
A key assignment for listen keys only. This assignment forces you to continuously listen to whatever is assigned to the talk
key. It is also useful to force listening when it is desirable to have an operator continuously hearing a particular source.
Auto Table (AT). A key assignment for listen keys only, when the corresponding talk key is assigned to an IFB. Auto Table
causes a listen key's assignment to always be the same as the Listen Source for whatever IFB is currently assigned to the talk
key. (You define the Listen Source in AZedit during IFB setup.) Auto Table is convenient in a broadcast environment when a
director needs 2-way communication with the IFB talent, AND the IFB keys are frequently reassigned during the course of a
program to talk to new talent locations. Using AZedit, several IFBs can be set up in advance, and their Listen Sources can also
be defined during setup. Then every time an IFB talk key is reassigned on a keypanel, the Listen Source for each new IFB
automatically becomes the listen key assignment for that key.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
92 Glossary
KP-32 Classic
Crosspoint. The term Crosspoint, like the term Matrix is inherited from intercom systems, such as the RTS CS9500,
CS9600, and CS9700, that use a switching matrix to route intercom audio. In those systems, the crosspoints are the actual
switches that close or open to connect or disconnect talk and listen paths. RTS ADAM, Cronus, and Zeus Intercom Systems do
not actually use crosspoint switches, but use a technique called time division multiplexing (TDM), in which communications
are routed as digital packets. However, use of the term crosspoint persists since packet routing basically accomplishes the
same thing as conventional crosspoints: namely, connecting distinct talkers and listeners. In this sense, a crosspoint can be
thought of simply as a communication link between any two (2) points in the intercom system.
Destination. A destination is anything that a talk key talks to. A assignment can therefore be any port, party line, IFB, etc.
DIM. DIM occurs in two (2) contexts in RTS Digital Matrix Intercom Systems.First, there is the DIM Table feature. DIM
tables are used to correct a feedback problem that can occur between two (2) keypanels operating in close proximity that have
keys assigned to talk/listen to a common destination. DIM tables are set up in AZedit. Once a dim table is set up, it can be
assigned as a level 2 talk assignment for those keys that are causing the feedback problem. For information, see “Service
Menu, DIM” on page 63. There is also an adjustable speaker dim feature available on the KP-32. This causes the speaker or
headphone volume to diminish by a preset amount whenever a talk key is activated. This can help to prevent occasional
feedback between the speaker and microphone due to volume settings, microphone placement, etc.
GPIO. General Purpose Input / Output. (You may also see this referred to simply as GPI.) GPIO is a means of controlling
devices using switch contact closures, DC voltages, or similar methods. For example, you can control a lighting system from
keypanel keys, or key a transmitter from a talk key during transmit. Or, simply operate a light or buzzer for cueing. In ADAM
and 
Zeus III intercom systems, you can also control intercom events from external switches. You can activate key assignments,
close or open crosspoints, activate GPI outputs, etc. ADAM and Zeus III intercom systems all have a dedicated GPIO
connector (J27 on a Zeus Frame, J903 on an ADAM CS Frame, and J11 on the XCP-ADAM-MC Master Controller Breakout
Panel in an ADAM Intercom System). This connector supports eight (8) control inputs and eight (8) control outputs.
Additionally, one (1) or more UIO-256 Universal Input/Output frames may be connected to the intercom system. Each GPIO16 provides another 16 control inputs and 16 control outputs. Control outputs may be assigned to intercom keys using the
Relay key assignment type, and the intercom keys can then control external devices. Control inputs can be assigned to activate
virtual key assignments. (A virtual key assignment is a key assignment at an intercom port where there is no keypanel
connected. Basically, you use an external switch to act like a talk or listen key.) The control inputs and outputs can also be used
as conditions for UPL statements in AZedit. Finally, there is a GPIO option available for the KP-12 and CLD keypanels, and a
connector module option for the KP-32, which includes GPIO. These are referred to as Local GPIO, since they are assigned
and used locally at the keypanel. Each local GPIO includes four (4) control inputs and four (4) control outputs.
IFB. IFB (Interrupt Foldback) is a special type of communication in which a listener at a particular intercom output port
normally hears an audio program source connected to a particular intercom input port. A keypanel operator can activate a key
to interrupt the audio program source and then talk to the listener. Normal operation resumes when the keypanel operator
releases the key. IFB is typically used to cue on-the-air talent. For example, the news anchor during a news broadcast typically
listens to the broadcast audio mix in an ear set (with the news anchor's own voice audio removed from the mix). A director at
a keypanel can interrupt the broadcast audio to the news anchor's ear set and provide new information to the news anchor. IFB
could also be used with a PA (public address) system that normally broadcasts background music. The background music can
be interrupted while someone is talking over the PA. IFB's are set up by defining the IFB inputs and outputs using the AZedit.
The intercom output port is called the IFB output and the program input port is called the IFB input. IFBs can also be given
names which are meaningful to keypanel operators. Once an IFB has been set up and named, it can be assigned to any
keypanel key.
ISO (Camera ISO). ISO is a means for a keypanel operator to isolate a particular intercom port for private communication.
While the intercom port is isolated, it can only talk to and hear the keypanel operator. ISO is frequently used in television
broadcasting to temporarily isolate a member of a camera party line. The isolated camera operator can then receive directions
without interference from other audio traffic on the party line. ISOs are setup using AZedit. Each ISO can also be given a
name which is meaningful to keypanel operators. Once an ISO has been set up and named, it can be assigned to any keypanel
key
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
Glossary 93
Matrix. Matrix is a term inherited from earlier point-to-point intercom systems, where all point-to-point communication was
accomplished by closing specific switches in a switching matrix. Matrix is used interchangeably with Intercom System. See
Crosspoint.
Party Line (PL). A party line (also called a conference) is a group of intercom ports which can always talk and/or listen to
each other. Party lines have default names PL01, PL02 etc. These names can be changed to more meaningful names using
Other Alpha setup in AZedit. Ports are made permanent talkers and/or permanent listeners of a party line. Party lines can also
be assigned to a keypanel key either from the configuration software or at a programmable keypanel. This allows the keypanel
operator to talk and/or listen to the party line without being a member.
IMPORTANT:
Do not confuse special lists and party lines. A special list is used when a keypanel operator needs to
occasionally talk or listen to a fixed group of intercom ports that are otherwise unrelated. A party line is
typically used when several users of non-keypanel devices (such as belt packs or camera intercoms) are
engaged in a specific common activity and they need to talk and/or listen to each other all the time.
Keypanels are almost never members of party lines (although they can be). However, a keypanel key
can be assigned to occasionally talk or listen to a party line if desired.
Port. The ports are the individual channels that devices are connected to. Devices include:
•
•
•
2-way communication devices, such as keypanels, belt packs etc.
Audio sources, such as broadcast feeds or background music.
Miscellaneous audio output devices, such as powered loudspeakers, PA systems etc.
Communication between Ports (Point-to-Point, or P-P): The audio signal from any input port can be routed to any output port.
During keypanel setup, you assign keypanel keys so that keypanel operators can talk and listen to other intercom ports.
You can also route signals between intercom ports without keypanels. To do this is to force crosspoints in the Crosspoint Status
screen of AZedit. Another way to do it is with a GPI input.
Port ID Numbers and Alphas Intercom ports have identification numbers 001, 002 etc. These numbers cannot be changed, but
may not be commonly known to intercom system users. Each intercom port also has a default name, called an alpha, because
this name appears in the alphanumeric displays on keypanels when you assign the ports to keys for talking and listening. The
default alpha names are N001, N002 etc. These default alpha names can be changed to ones that are meaningful to keypanel
operators using Port Alpha setup
To assure signal level compatibility between the various types of audio devices connected to the intercom system, there are
separate analog input and output gain adjustments for each intercom port. It is also possible to adjust the listen gain for any
specific intercom port when listening to any other specific intercom port. This is called the point-to-point listen gain, or
crosspoint gain. Analog gain adjustment is only available using AZedit. Crosspoint gains can be adjusted either within AZedit
or from a programmable keypanel.
Relay. Relay is used interchangeable with GPI output. The relay feature works with the 16 GPI outputs of an optional UIO256 Universal Input / Output Frame. The relay feature also works with the eight (8) GPI outputs of an ADAM, ADAM CS, or
Zeus intercom system (J27 on a Zeus Frame, J903 on an ADAM CS Frame, and J11 on the XCP-ADAM-MC Master
Controller Breakout Panel in an ADAM Intercom System). You can assign a keypanel key to control a GPI output from any of
these devices, and then use that key and output to control an external device.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
94 Glossary
KP-32 Classic
Special List. A special list is a means for a keypanel operator to talk and/or listen to several unrelated destinations using a
single key. Special lists are useful for group call or zone paging. A special list is a group of intercom ports that a keypanel
operator can talk or listen to by activating a single key. Special lists are typically used for paging, all call, group call etc.
Special lists have default names SL01, SL02 etc. These names can be changed using Other Alpha setup. You define the
members of the special list using Special List setup. Once a special list has been set up, you typically assign it to a keypanel
key using Keypanel setup. The keypanel operator can then activate the special list key to talk or listen to all members of the
special list.
IMPORTANT:
Do not confuse special lists and party lines. A special list is used when a keypanel operator needs to
occasionally talk or listen to a group of intercom ports that are otherwise unrelated. A party line is
typically used when several users of non-keypanel devices (such as belt packs or camera intercoms) are
engaged in a specific common activity and they need to talk and/or listen to each other all the time.
Keypanels are almost never members of party lines (although they can be). However, a keypanel key
can be assigned to occasionally talk or listen to a party line if desired. Just remember: party lines are
primarily set up for party line members, with occasional access by keypanel operators, while special
lists are set up exclusively for keypanel operators to talk or listen to several unrelated intercom ports.
Stacked Key. See the descriptions for talk level 1 and talk level 2.
Talk Level 1. Talk level 1 is the normal talk key assignment. This is the assignment that normally appears in the
alphanumeric display. You may add a talk level 2 assignment to activate a second P-P or a PL, along with talk level 1.
Talk Level 2. Talk level 2 is used with stacked talk keys. A stacked talk key activates two types of communication at once.
For example, a stacked talk key could simultaneously activate audio output to a transmitter and key the transmitter using a
relay.
NOTE:
You can configure the intercom for up to four (4) talk levels.
Trunking. Trunking is a method of interconnecting two (2) or more independent intercom systems. The connection is
accomplished by reserving one (1) or more audio ports in each of the intercom systems for use as audio links between the
systems. A special device, called a Trunk Master, is required to control access and usage for the trunked intercom ports. A
configuration utility, called TrunkEdit, is used to set up the Trunk Master.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
APPENDIX A
OKI Option Card Installation
Install the OKI Option Card
IMPORTANT:
Verify you have updated the boot loader and keypanel firmware on the KP-32 Classic keypanel before
installing the OKI option card. For more information, see “Upgrade the KP-32 Boot Loader Version” on
page 17.
To install the OKI board set for the KP-32 Classic, do the following:
1.
Power off the KP-32 Classic keypanel.
2.
Using a Phillips screwdriver, remove the four (4) corner screws from the back panel.
NOTE: Steps 3 and 4 are only necessary if you have an RC option installed.
3.
Using a hex nut driver, remove the 14 hex screws from the back panel.
4.
Remove the eight (8) pan head screws from the back panel.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
96
KP-32 Classic
5.
Using a Phillips screwdriver, remove the flat head screws from top, bottom and back panel.
6.
Carefully attach the OKI board set J1 to the KP-32 Classic main board J4, as shown.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
97
7.
Carefully replace the back panel on the KP-32 Classic.
8.
Replace the four (4) corner pan head screws that attach the back panel.
9.
Taking care to ensure the Ethernet connectors are flush to the chassis, use the two (2) pan head screws provided to
secure the OKI board to the chassis.
NOTE: Steps 10 and 11 are only necessary if you have an RC option installed.
10.
Replace the 14 hex screws.
11.
Replace the eight (8) pan head screws.
12.
Replace the top cover.
13.
Replace the flat head screws.
14.
Power on the KP-32 Classic keypanel.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
98
Bosch Security Systems, Inc.
KP-32 Classic
User Manual
F.01U.193.253
Rev. 21
APPENDIX B
RVON-1
General Description of the RVON-1 Voice Over Network Card
Installed directly into KP-32 keypanels, the RVON-1 provides VoIP (Voice over Internet Protocol) communications, for the
RTS ADAM Intercom family. In general, voice over IP means sending voice information in digital form using discrete packets
rather than the traditional hard-wire connection. The RVON-1 delivers an integrated solution for connecting keypanels to the
Intercom matrix over standard IP networks.
The RVON-1 is compatible with any RTS Matrix Intercom System equipped with a suitable RVON interface. In conjunction
with any new or existing KP-32 or KP-812 keypanel, the RVON-1 brings a new level of enterprise-wide and remote access
functionality to your RTS Matrix Intercom.
The RVON-1 card is configurable through the keypanel service menu and RTS’s IPedit configuration software. It is also fully
compatible with internationally recognized standards and supports the following protocols: G.711, G.729 A, and G.723 (2-Bit
rates).
The RVON-1 reaffirms RTS’s history of providing support for the latest technology in a fully supported backward compatible
manner to all its RTS products.
Features
Installation
The RVON-1 provides a single RJ-45 Ethernet connection for use with a 10 BASE-T or 
100 BASE-TX network.
1 Channel of Audio
in and out
The RVON-1 card supports one (1) channel in and out and has configurable network and
bandwidth parameters that can be tailored to individual network functions.
Ethernet
Compatible
The RVON-1 card uses standard Ethernet protocols.
IPedit
Configurations
Users have the ability to adjust the audio parameters of the RVON-1 channel to optimize the
available bandwidth.
Swappable Between
Ethernet and AIO
Connection
When connected to an Ethernet LAN, audio comes from the RVON-1 card; and, when an Ethernet
link is not present, the audio comes from the AIO connection. Note, the user does not need to
remove the RVON-1 card to switch to AIO mode.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
100
KP-32 Classic
Specifications
Digital
Compression
Audio Bit Rate
Coding Delay
Playout Delay
IP Bandwidth
G.711
64k
125s
20-60ms
160-224 kbps
G.729AB
8k
10ms
20-120ms
32-112kbps
G.723
5.3k/6.3k
30ms
60-120ms
29-45kbps
NOTE: The Playout Delay and Bandwidth depend on the configured amount of audio per packet.
Connections
• RJ-45 Ethernet via backcard
• 14-pin KP Compatible Expansion Connector
Pin 1............................................................................................................................... 5 Volt Analog
Pin 2........................................................................................................................................ -12 Volt
Pin 3........................................................................................................................................+12 Volt
Pin 4................................................................................................................................5 Volt Digital
Pin 5................................................................................................................................ Analog GND
Pin 6.................................................................................................................................Digital GND
Pin 7.......................................................................................................................To Matrix Audio L
Pin 8................................................................................................................................................NC
Pin 9.................................................................................................................. From Matrix Audio L
Pin 10...................................................................................................................................... RS485L
Pin 11................................................................................................................ From Matrix Audio H
Pin 12..............................................................................................................................................NC
Pin 13.................................................................................................................... To Matrix Audio H
Pin 14......................................................................................................................................RS485H
Power............................................................................................................... Powered internally from keypanel
motherboard
Physical ........................................................................................................... 2.5”W x 5.75”L (63.5mmW X
146.05mmL)
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
101
Default Addresses for the RVON Product Line
TABLE 3. Default
Address for the RVON Product Line
Product
Default IP Address
Default Subnet Mask
RVON-I/O
192.168.0.1
255.255.0.0
RVON-8
192.168.0.2
255.255.0.0
RVON-1
192.168.0.3
255.255.0.0
RVON-C
192.168.0.4
255.255.0.0
RVON-16
192.168.0.5
255.255.0.0
GPIO-16
192.168.0.6
255.255.0.0
MCII-e
192.168.0.7
255.255.0.0
Cronus
192.168.0.8
255.255.0.0
Zeus III
192.168.0.9
255.255.0.0
Dip Switches
Switch
1
Reserved
Switch
2
Disable Telnet Shell
Switch
3
Switch
4
Default
Setting
Off (Telnet Enabled)
Description
The Telnet shell allows you to access configuration options through the use of Telnet. When
DIP switch 2 is off, you can use Telnet to access configuration options on the RVON-1 card.
Turn DIP switch 2 on to disable the Telnet shell.
Enable Boot Loader
Default
Setting
Off (Boot Loader Disabled)
Description
The purpose of the boot loader is to allow you to recover from having your main application
image corrupted (either by bad flash programming or by downloading an invalid image). Turn
DIP switch 3 on to enable the boot loader.
Debug Only!
Default
Setting
Off
Description
DIP switch 4 should always be left in the off position. It is reserved for debugging and can
have unintended consequences.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
102
KP-32 Classic
Firmware Compatibility Requirements for the RVON-1 Card
TABLE 4. Compatibility
Requirements for the RVON-1 card.
Description
Version
Master Controller
9.19.0 or later
Peripheral Controller
10.10.0 or later
DBX
1.10.1 or later
IPedit
2.06.06 or later
RVON-16
1.1.0 or later
KP-32
2.0.0 or later
Flash Chip Replacement
TABLE 5. Flash
Chip replacement part numbers.
Keypanel
KP-32 Standard
KP-32 (Japan)
Flash Chip Replacement
9015-7656-002 (U2)
9015-7656-003 (U3)
9015-7656-042 (U2)
9015-7656-043 (U3)
9015-7656-202 (U2)
KP-632
9015-7656-203 (U3)
9015-7656-302 (U2)
KP-832
9015-7656-303 (U3)
Flash Chips
U2 U3
FIGURE 12.
Flash Chip placement on the KP-32 motherboard
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
103
Installation of the RVON-1 Card
Before using the RVON-1 card with the KP-32, a few modifications need to be made to the keypanel. If the serial number on
your KP-32 is 61170 or earlier, you must update your back panel with the Ethernet RJ-45 connection knockout present. Also,
the KP-32 flash chips need to be replaced with larger flash chips (4MB), see Table 5 on page 102.
To install the RVON-1 card, do the following:
1.
Remove the cover from the KP-32.
2.
If present, remove the GPI/O board.
The GPI/O board contains the general purpose input and output connections located on the back cover.
3.
Using a chip extractor, carefully remove and replace the flash chips located at U2 and U3 on the KP-32 motherboard.
4.
Using a hammer and screwdriver, remove the knockout pieces.
5.
Mount the supplied spacer on the RVON-1 card on the corner of the card near the DIP switch. Securely connect the
RVON-1 card to the KP-32 motherboard.
Screw Hole - for RVON-1 stability purposes
CSI Connection
RVON-1 Ethernet Connection
AUX 1 IN
AUX 2 IN
RELAY 1 & 2
OUT
OPTO 1-4
IN
HEADSET
MIC IN
MIC OUT
Frame
RELAY 3 & 4
OUT
FOOT SW
/SPEAKER
O.C. 1 & 2
OUT
Open
Options
Power
HEADSET
Closed
PANEL
R
TELEX COMMUNICATIONS, INC.
Address
MADE IN U.S.A.
Exp.
LCP
Frame
MIC GAIN
6.
Replace the GPI/O board.
7.
Re-attach the back plate to the KP-32. Be sure to secure the spacer with a screw in the back plate.
8.
Replace the cover on the KP-32.
NOTE:
•
In the KP-32, the RVON-1 card connects to the KP-32 by way of the J2 connector on the RVON-1,
attached to J4 on the KP-32 header.
•
In the KP-812, the RVON-1 card connects to the KP-812 by way of the J2 connector on the RVON,
attached to J37 on the KP-812 header.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
104
KP-32 Classic
9.
Gently secure the board in place.
NOTE:
Be sure the orientation of the board is correct, otherwise undesirable effects may occur. Make sure the RJ-45
connection is positioned so it fits through the specified knockout on the back cover. When installing the RVON-1
card in an existing KP-32 or KP-812, each keypanel needs to be upgraded to include the following:
KP-32
•
A back plate that allows for the RJ-45 connection (Ethernet).
RVON-1 Relay
When connected to an Ethernet LAN, audio comes from the RVON-1 card; and, when Ethernet is not plugged in, the audio
comes from the AIO connection. Note, the user does not need to remove the RVON-1 to switch to AIO mode.
WARNING:
You cannot have both an Ethernet connection and an AIO connection simultaneously. If the Ethernet and
AIO are connected simultaneously, no audio communication occurs.
Addresses and the RVON-1
Because the RVON-1 has an Ethernet interface, it is required to have a MAC (Media Access Control) Address. This is a low
level address that contains 48 bits. Do NOT confuse this address with an IP (Internet Protocol) Address. In order to be IP
compliant, all cards must have a unique MAC ID when shipped from the manufacturer. Typically, the MAC ID of a piece of
hardware, such as the RVON-1 card, has a fixed or static address, whereas the RVON-1 card’s IP Address can change over
time.
The MAC Address uniquely identifies each node of a network and interfaces directly with the network media. The RVON-1
card has a small 8-pin serial device on the board that the processor can read the unique MAC Address from. For more
information on MAC IDs, contact technical support.
NOTE:
Each RVON-1 card needs to be programmed with its own IP Address.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
105
Configure the RVON-1 from the KP-32
To use the RVON-1 with the KP-32, the KP-32 firmware must be at version 2.0.0 or higher. In turn, the firmware requires that
larger flash chips be used as well (see “Flash Chip Replacement” on page 102).
Top Level Menu, Service, RVON Setup
Set the IP Address from the Service Level Menu
The RVON-1 card, when shipped has a default IP Address already configured. This must be changed in order for the RVON-1
card to function properly because the pre-configured IP Address may not work with your network.
To set the IP Address, do the following:
1.
On the KP-32, press Menu.
The top level menu appears.
2.
Using the down arrow keys, scroll to Service.
3.
Press PGM.
The Service menu appears.
4.
Using the down arrow keys, scroll to RVON Setup.
5.
Press PGM.
The IP Address menu item appears.
6.
Press PGM.
The actual IP Address appears.
NOTE: If you don’t need to modify the entire address, press PGM to skip over any octet that does not need
modifications.
7.
Enter the first number in the IP Address.
This enters the first octet of the IP Address and clears the rest of the IP Address.
8.
Press PGM.
This confirms the first octet in the IP Address and moves you to the second octet.
9.
Repeat steps 7 and 8 until the entire IP Address is entered.
10.
Press PGM.
The Netmask menu item appears.
NOTE: Once you have entered the IP Address, then enter the Netmask. The Netmask is a string of numbers similar
to an IP Address, except that it masks or screens out the network part of an IP Address so that only the host
computer part of the address remains (for example, 255.255.255.0).
11.
Press PGM.
The actual Netmask appears.
12.
Enter the Netmask in the same manner as the IP address.
13.
Press PGM.
The Gateway IP Address menu item appears.
NOTE: Once you have entered the Netmask, you may need to enter the Gateway IP Address. A Gateway is a node
(for example, a computer) on a network that forwards packets to another network.
14.
Press PGM.
The actual Gateway IP Address appears.
15.
Enter the gateway IP Address in the same manner as the IP Address. If there is no gateway IP Address, set the
address to 0.0.0.0.
16.
Press PGM.
17.
Press CLR to exit.
The changes are now enabled.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
106
KP-32 Classic
Top Level Menu, RVON Conn.
Select an RVON Connection from the Top Level Menu
The RVON Conn menu contains a list of connection offers from intercoms. This menu allows the keypanel to dynamically
select an intercom and port to which it connects.
To select a connection offer, do the following:
1.
On the KP-32, press Menu.
The top level menu appears in the CWW window.
2.
Using the down arrow keys, scroll to RVON Conn.
3.
Press PGM.
The currently selected intercom port appears in the CWW window. If you have not previously selected a connection,
you see <none>.
4.
Using the down arrow keys, scroll to the connection offer that you want to accept.
5.
Press PGM.
<connection offer> appears. The arrow to the left of the offer designates which connection offer was chosen.
6.
Press CLR to exit.
The keypanel is now connected to the selected intercom port.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
107
Configure the RVON-8 via AZedit to contact the RVON-1
To configure the RVON-1 card, do the following in AZedit:
1.
From the Status menu, select I/O Cards.
The I/O Card Status window appears showing the types of installed.
2.
Right click on an RVON card and select RVON Configuration.
The RVON Configuration window appears.
NOTE: The RVON-8 you use should be already configured. If it is not configured, refer to your RVON-8 Card User
Manual. Remember, the RVON-1 has only one (1) channel that can be configured.
3.
In the RVON-8 Channel drop down list, select the channel to be used to connect to the RVON-1 card across the
network.
4.
In the Device IP field, enter the IP Address for the RVON-1 card.
5.
From the Device Type drop down list, select RVON-1/Keypanel.
6.
From the Device Channel drop down list, select Channel 1.
There may be two (2) channels listed, but the connection can only be made through channel 1.
7.
From the CODEC Type drop down list, select the Codec type.
8.
From the Packet Sized drop down list, select the size of each audio packet.
NOTE: A CODEC is an algorithm used to compress audio. Codecs dictate the quality of audio you hear and the
network bandwidth used. The packet size determines how much audio data is carried across the network in
each transmitted packet. The Codec type and packet size chosen require different amounts of bandwidth
from the network. As with the CODEC type, the packet size you choose for the audio transfer affects the
audio you hear and the bandwidth you use over the network. The larger the audio packet you choose to use,
the lower the bandwidth used. However, the larger packet size can result in a higher delay and longer gaps if
the packet is lost. On the other hand, smaller packet sizes result in larger bandwidth use, but lower delays
and smaller gaps if a packet is lost. The Intercom System Engineer and the Network Designer may want to
work together in choosing the Codec type and packet size suitable for the size of the network, so degradation
of network resources does not occur.
9.
Select Enable VAD (Voice Activation Detection), if you want to conserve bandwidth when the audio level is below
a given threshold.
NOTE: VAD saves network bandwidth by stopping the flow of audio packets when silence is detected. VAD is
similar to VOX.
10.
Once you are completely finished, click Apply.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
108
KP-32 Classic
Download RVON-1 Firmware Through AZedit
NOTE:
AZedit sends firmware directly to the RVON-1 card over Ethernet. This is different from other I/O cards (except
the RVON-8) that receive the firmware from the Master Controller. For this reason, verify the PC running AZedit
is able to contact the RVON-1 card via the network. If it is not, AZedit is not able to connect to the RVON-8 card.
To test the connection, ping the RVON card from a command line prompt. For more information on how to test
for a connection, see “Basic Network Configuration” on page 111.
To download the RVON-1 Firmware, do the following:
1.
Open AZedit.
2.
From the Status menu, select Software Versions and then Keypanels.
The Keypanel Version window appears.
3.
On the Keypanel Version window, select the Show RVON/OMNEO Versions check box.
4.
Select and right click the keypanel which has the RVON-1 installed, and then select Download RVON.
The Download Device Firmware window appears.
5.
Using the Browse feature, browse to the file to be downloaded.
6.
Click Open.
The Download Device Firmware window appears.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
109
7.
Click Begin Download.
The download begins.
8.
Click OK.
The RVON-1 firmware download is complete. This takes a minute or two (2) to occur.
WARNING:
9.
Do NOT power down the keypanel until you have verified the new version information from AZedit. If the
card loses power while reprogramming the onboard flash memory, the card may become unbootable and
may need to have its flash chips reprogrammed at the factory.
Verify the correct version is shown on the Keypanel Version window.
NOTE: You can also download the RVON-1 firmware through Status > Ports. You are not able to check the version
once the download is completed from the Port Status window.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
110
Bosch Security Systems, Inc.
KP-32 Classic
User Manual
F.01U.193.253
Rev. 21
APPENDIX C
Basic Network Configuration
Basic Network Configuration
This section covers basic network configuration set-up and testing. Also covered are basic concepts and operations, including
the difference between LAN and WAN networks and how IP Addressing is used.
In a networked environment, such as a company, typically there are many computers connected together using a router or a
switch. In larger companies, there may be several different routers distributed in buildings and plant locations. A router allows
any LAN-side computer to communicate with other computers and devices outside the LAN (local area network). Routers
send data packets from one (1) place to another place on a network. Routers use network addresses to route packets to the
correct destination. For example, in a TCP/IP network, the IP (internet protocol) address of the network interface is used to
direct router traffic.
Because routers allow computers inside the LAN to communicate with computers outside of the LAN, the security of a
company’s LAN may be compromised by open ports in the router. Security measures may have been instituted to compensate
for these vulnerabilities. Consult your network administrator to learn about the security measures taken to protect your
network. VPN, or virtual private network, is one (1) such security measure to protect the intelligence of the LAN. A computer
outside the LAN must have a key known by the VPN to allow access to the LAN. Many companies use a VPN to connect 
two (2) different LANs, thus allowing the transfer of data between two (2) networks.
LAN vs. WAN
Local Area Network
Simply put, a LAN (Local Area Network) is a computer network that connects a relatively small area (a single building or
group of buildings). Most LANs connect workstations and computers to each other. Each computer (also known as a “node”),
has its own processing unit and executes its own programs; however, it can also access data and devices anywhere on the LAN.
This means many users can access and share the same information and devices. A good example of a LAN device is a network
printer. Most companies cannot afford the budgetary or hardware expense of providing printers for each of its users; therefore,
one printer (or device) is placed on the LAN where every user can access the same printer.
The LAN uses IP Addresses to route data to different destinations on the network. An IP Address is a 32-Bit numeric address
consisting of four (4) numbers separated by periods (for example, 1.160.10.240).
NOTE:
For more information on IP Addresses, see you local network administrator.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
112
KP-32 Classic
FIGURE 13.
Local Area Network Diagram
Wide Area Network
A WAN (Wide Area Network) connects two (2) or more LANs and can span a relatively large geographical area. For example,
Bosch Security Systems Headquarters in Burnsville, MN is connected to several branch offices in Nebraska and Hermosillo
over a WAN. The largest WAN in existence is the Internet.
FIGURE 14.
Wide Area Network Diagram
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
113
Accessing The Wide Area Network (WAN)
Figure 15 shows LAN IP Addresses using a common IP Address, 10.2.100.X (192.168.X.X is another common address). Most
devices are shipped with these addresses as its default. It is recommended to use these addresses for LANs.
FIGURE 15.
Network Address Translation
Ports
In general, a network port is an endpoint to a logical connection. The port number identifies what type of port it is. For
example, TCP port 80 is used for HTTP traffic. When you type an address into the address bar of a web browser, your
computer goes to find an IP Address for the URL you are requesting (http://www.telex.com). To obtain this address, the
computer contacts a DNS server (Domain Name Server). Once the IP Address is found, it tries to connect to the http port of the
network device (port 80). See Table 8 on page 114 for a list of the more well-known port numbers.
Each network device can be set-up to respond or not respond to the various ports. The function of responding or “hosting a
service” is called “serving”.
TABLE 6. Packet
Translation
Packet before Translation
Source
Packet after Translation
Destination
Source
Destination
IP Address
Port
Number
IP Address
Port
Number
IP Address
Port
IP Address
Number
Port
Number
To
Internet
10.2.100.2
1031
192.156.136.22
80
99.5.1.30
1031
192.156.136.22
80
From
Internet
192.156.136.22
80
99.5.1.30
1031
192.156.136.22
80
10.2.100.2
1031
If a second workstation on the LAN wants to communicate to the same server, and happens to use the same source port
number, then the LAN Modem translates the source port number as well as the source IP address. In Table 6, a second LAN
computer wants to access a web page. The NAT device now uses port 1032 for this connection where it used port 1031 in
Table 7.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
114
KP-32 Classic
TABLE 7. Packet
Translation
Packet before Translation
Source
Packet After Translation
Destination
Source
Destination
IP Address
Port
Number
IP Address
Port
Number
IP Address
Port
Number
IP Address
Port
Number
To
Internet
10.2.100.1
1031
192.156.136.22
80
99.5.1.30
1032
192.156.136.22
80
From
Internet
192.156.136.22
80
99.5.1.30
1032
192.156.136.22
80
10.2.100.1
1031
Amazingly, all the address translation that occurs takes place
automatically in order to make web browsing and other
functions easier. This is also a way for large web hosting
services to speed up the network by having different devices
perform different functions.
TABLE 8. Well-known
TABLE 8. Well-known
TCP Port Numbers
Port Number
Description
TCP Port Numbers
Port Number
Description
119
Newsgroup (NNTP)
137
NetBIOS Name Service
139
NetBIOS Datagram Service
143
Interim Mail Access Protocol (IMAP)
150
NetBIOS Session Service
156
SQL Server
1
TCP Port Service Multiplexer
(TCPMUX)
5
Remote Job Entry (RJE)
161
SNMP
7
ECHO
179
Border Gateway Protocol (BGP)
18
Message Send Protocol (MSP)
190
20
FTP-Data
Gateway Access Control Protocol
(GACP)
21
FTP- Control
194
Internet Relay Chat (IRC)
23
Telnet
197
Directory Location Services (DLS)
25
Simple Mail Transfer Protocol (SMTP)
389
Lightweight Directory Access Protocol
(LDAP)
29
MSG ICP
396
Novell Netware over IP
37
Time
443
HTTPS
42
Host Name Server (Nameserv)
43
Whols
444
Simple Network Paging Protocol
(SNPP)
49
Login Host Protocol (Login)
445
Microsoft-DS
53
Domain Name Server (DNS)
458
Apple Quick Time
69
Trivial File Transfer Protocol (TFTP)
546
DHCP Client
70
Gopher Service
547
DHCP Server
79
Finger
563
SNEWS
80
HTTP
569
MSN
103
X.400 Standard
1080
Socks
108
SNA Gateway Access Server
109
POP2
110
POP3
115
Simple File Transfer Protocol
118
SQL Services
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
115
IP Addresses
If you do not know your IP Address, an MS-DOS command window and run the ipconfig command.
To find your IP Address using ipconfig, do the following:
1.
From the Start Menu, open a Command Prompt window.
2.
At the command prompt, type ipconfig, then press Enter.
The IP configurations appear for your machine, such as the DNS suffix, IP Address, Subnet Mask, and Default
Gateway.
3.
At the command prompt, type Exit to close the window.
NOTE: If you want more detailed parameters for your machine, type ipconfig/All. This displays the computer’s
network configuration settings.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
116
KP-32 Classic
Ping a Computer
Pinging a computer on the network makes sure it is able to be “seen” and receive messages on the network.
NOTE:
You can also ping your RVON-8 card to verify that it is responding over the network by putting the card’s IP
Address in place of the computer IP Address.
To Ping a computer on the network, do the following:
1.
From the Start menu in the Run field, type CMD to open a Command Prompt window.
2.
At the command prompt, type the IP Address of the computer you wish to ping (for example, 10.2.100.130).
3.
Press Enter.
NOTE: If the computer you are pinging is not responding to the ping, you receive a time-out message in the
Command Prompt window.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
117
Possible Pitfall With Routers, Gateways, And Switches
Any time computers communicate through routers, gateways, and switches, they may be allowed or denied the connection.
Network interface devices can be configured to block specific outgoing requests, as well as incoming requests, based on the IP
Address and/or port. This is one (1) of the security mechanisms of a router.
To view the path an IP Address takes to retrieve information, do the following:
1.
From the Start Menu, open a Command Prompt window.
2.
At the command prompt, type tracer-d and type the URL or IP Address you want to trace.
3.
Press Enter.
The details of the tracer route are displayed.
NOTE: You see the message “request timed out” if the IP Address/port IN or OUT is denied to the incoming or
outgoing message.
4.
When you are finished, type exit to close the Command Prompt window.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
118
KP-32 Classic
RVON Configuration
RVON cards use ports for communication of audio and control packets. Because routers can be configured to block certain
incoming and outgoing requests, you must open the following ports in your network to allow WAN connections to and from a
Network Interface Device. See Table 9 on page 118 for the ports that need to be opened for the RVON cards to operate
properly.
TABLE 9. Ports
necessary for RVON card functionality.
Port
Port Description
2076
UDP Call Control Signalling
2077
UDP Audio Packets
2079
UDP Telex Proprietary Signalling
2080
TCP Telex Keypanel Protocol
2081
UDP Pass Through Serial
2082
TCP Firmware Download
2100
Remote Administration
2102
Authentication Server
Below, is an example of a router configuration screen. Not all routers are configured the same way and may not look exactly
like this window.
Figure 10. Forwarding
NOTE:
Window
Linksys supports up to 253 nodes on a router. This is why it is called a Router/Switch because there are WAN
functions like a router as well as having a 4-port LAN switch.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
119
Network Terminology
Bridge
A bridge is a device that connects two (2) LANs, or two (2) segments of the same LAN that
use the same protocol. Sometimes called “transparent bridges” they work at the OSI model
layer 2. Simply put, they are not concerned with protocols. Their main job is to pass data to a
destination address that is predetermined in the data packet.
With a bridge, all of your computers are on the same network subnet (see Subnet). This means
your computers can communicate with each other an have their own internet connection. If
you assign your own IP addresses be sure to use the same first three (3) octets of the IP
Address.
Domain Name Server
(DNS)
A DNS Server is an internet service that translates domain names (for example, in the URL
http//www.telex.com, the domain name is telex.com) into IP addresses. The internet is based
on IP addresses which are numeric, and since domain names are alphabetic, they are easier to
remember. Every time a domain name is used it must go through the DNS server to be
translated.
Gateway
A gateway is a node on a network that serves as an entrance to another network. The gateway
routes traffic from a computer to an outside network that is serving the web pages. For
example, the gateway for a home computer is the ISP provider that connects the user to the
Internet.
In a corporate environment, the gateway often acts as a proxy server and a firewall. Gateways
are similar to routers and switches, in that they forward data to the destination and provide the
path for which the data travels to the destination.
Hub
A hub is a common connection point for devices in a network. A hub has multiple ports.
When a data packet arrives at a hub, it is copied and distributed to all of its ports so that all
nodes on the LAN can see the packets.
There are two (2) types of hubs:
Bosch Security Systems, Inc.
•
passive hub - this hub serves as a conduit for the data, enabling it to go
from one device to another.
•
intelligent hub - (also known as manageable hubs) this hub includes
additional features that enable administrators to monitor traffic through
the hub.
User Manual
F.01U.193.253
Rev. 21
120
KP-32 Classic
IP Address
(Internet Protocol
Address)
An IP Address is an identifier or numerical name for a computer or device on a network. Data
between computers are routed over the network using these addresses to identify the
computer the message being sent to and the computer the message is being set from.
The format of an IP Address is a 32-Bit numeric address written as four numbers separated by
periods. For example, an IP Address looks like 10.100.1.1.
IMPORTANT:
When working within an isolated network (meaning there is no
Internet access), IP Addresses can be assigned at random just as long
as they are unique to each computer and device. When the isolated
network is connected to the Internet, registered Internet Addresses
must be obtained. This is to prevent duplication of addresses.
The four numbers in an IP Address are used in different ways to identify a particular network
and host on the network.
LAN
A LAN is a computer network that connects a relatively small area (a single building or group
of buildings). Most LANs connect work stations and computers to each other. Each computer
(also known as a “node”) has its own processing unit and executes its own programs;
however, it can also access data and devices anywhere on the LAN. This means that many
users can access and share the same information and devices. A good example of a LAN
device is a network printer. Most companies cannot afford the budgetary or hardware expense
of providing printers for each of its users; therefore, one printer, (i.e., device) is placed on the
LAN where every user can access the same printer.
The LAN uses IP addresses to route data to different destinations on the network.
Port
A port, when referring to TCP and UDP network, is an endpoint in a logical connection. The
port number identifies the type of port it is. For example, TCP port 80 is used for HTTP
traffic.
Routers
A router is a device that forwards data packets over networks. Most commonly, a router is
connected to at least two (2) networks (normally LANs or WANs). Routers are the place
where two networks are connected. Routers do little data filtering, they mainly deliver the
data.
Subnet
A subnet is a portion of a network that shares a common address component. On a TCP/IP
network, a subnet is described as all computers or devices whose IP Address have the same
prefix.
Subnetting a network is useful because it provides security for the network, as well as
increasing performance of the network. IP networks are divided using subnet masks.
Switches
A switch is a device that filters and forwards data packets between networks. Switches
operate at the data layer, and sometimes at the network layer.
WAN
A wide area network connects two or more LANs and can span a relatively large geographical
area. For example, Bosch Security Systems Headquarters in Burnsville, MN is connected to
several branch offices in Nebraska and Hermosillo over the wide are a network. The largest
WAN is the Internet.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
APPENDIX D
Telnet & Serial Port Programming
RVON Serial and Telnet Commands
RVON card programming can be done via direct serial or telnet connection. There are several physical connections to an
RVON board:
•
•
•
Direct serial through custom debug cable (J20 6-pin connector)
Backcard DB-9 J2
RJ-45 J7 (Telnet Only)
Setup
Serial Port
Telnet
38,4000 baud, no flow control
IP Address, port 23
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
122
KP-32 Classic
How to Configure the RVON-1 using Telnet
Without access to the physical KP-32 with RVON-1 installed on it, you can still configure the card through the use of Telnet.
The following instructions shows you how to access the Telnet screen and show you some of the information you can see and
edit.
NOTE:
These instructions are to help you get to the Telnet screens and give you an overview of what can be done. This is
NOT an all inclusive document. Not every action that can be performed are contained within the document.
To display the settings for the RVON-1 card, do the following:
1.
Open a Command Prompt window.
2.
At the command prompt, type Telnet <IP ADDRESS> (The IP Address is the IP Address assigned to the RVON-1
card).
3.
Press Enter.
The RVON logon window appears.
4.
In the logon field, type the RVON logon (default = telex).
Press Enter.
In the password field, type the RVON password (default = password).
Press Enter.
A command prompt appears.
5.
6.
7.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
8.
123
Type dbgcmd to access the debug command windows.
Press Enter.
An MXP prompt appears.
10. At the prompt, type Show.
11. Press Enter.
The show commands window and MXP prompt appears.
9.
12.
13.
At the MXP prompt, type the show command you want to see (for example, “show rvon”).
Press Enter.
The values for the RVON-1 card appear.
To edit the RVON-1 configuration, do the following:
1.
Repeat steps 1 through 9 from above.
2.
At the MXP prompt, type either set RVON or set EMAC (see window descriptions below).
3.
Press Enter.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
124
KP-32 Classic
set rvon ip_addr
Allows you to edit the IP Address
set rvon netmask
Allows you to edit the netmask
set rvon gateway
Allows you to edit the gateway
set rvon serial_ip
Allows you to edit the serial IP Address
set rvon serial_baud
Allows you to set the baud rate (50-38400)
set rvon user
Allows you to set the username for the RVON-1 card. By default the user name is “telex”
set rvon password
Allows you to set the password for the RVON-1 card. By default, the password is “password”
Lets you set the VAD threshold
set rvon vad_threshold
Bosch Security Systems, Inc.
NOTE:
In AZedit, you can enable and disable VAD, however, through Telnet you able to
set the amount. You are able to set the VAD threshold in IPedit.
User Manual
F.01U.193.253
Rev. 21
KP-32 Classic
125
set channel dest_ip
Allows you edit the destination IP Address the RVON-1 card communicates with
set channel dest_type
Allows you to edit the destination type for the device the RVON-1 card talks with
set channel dest_channel
Allows you to edit the destination channel of the device the RVON-1 talks with
set channel channel_codec
Allows you to edit the CODEC to be used for transferring the data between the two devices
set channel input_gain
Allows you to edit the input gain for the RVON-1 card
set channel output_gain
Allows you to edit the output gain for the RVON-1 card
set channel onhook
onhook = hang up
If the channel was already connected, going offhook has no effect (it is already offhook if
connected). Going onhook hangs up the call, and it should then try to reconnect.
If the channel was not already connected, going offhook causes it to try and establish a
connection. Going onhook in this state has no effect (it is already onhook if idle).
set channel offhook
offhook = connected
If the channel was already connected, going offhook has no effect (it is already offhook if
connected). Going onhook hangs up the call, and it should then try to reconnect.
If the channel was not already connected, going offhook causes it to try and establish a
connection. Going onhook in this state has no effect (it is already onhook).
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
126
Bosch Security Systems, Inc.
KP-32 Classic
User Manual
F.01U.193.253
Rev. 21
APPENDIX E
EKP-32 Expansion Panel
Installation Instructions
To connect the EKP-32 Expansion Panel to the KP-32, do the following:
1.
Insert one end of the provided RJ-45 cable into the EXP port on the back panel of the KP-32.
2.
Insert the other end of the provided RJ-45 cable into the EXP 1 port on the back panel of the EKP-32.
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
128
KP-32 Classic
Specifications
AC Supply
AC Input:
100-240 VAC, 50/60 Hz
Power Consumption
Nominal:
0.08 A
Maximum:
0.10 A
Maximum Volt Amp:
18 VA
General
Color:
Grey or Black
Depth:
5” (127 mm)
Height:
3.5” (88.9 mm)
Weight:
5.6 lb (2.54 kg)
Width:
19” (482.6 mm)
Bosch Security Systems, Inc.
User Manual
F.01U.193.253
Rev. 21
Bosch Security Systems, Inc.
12000 Portland Avenue South
Burnsville, MN 55337 U.S.A.
www.boschcommunications.com
130
Bosch Security Systems, Inc.
KP-32 Classic
User Manual
F.01U.193.253
Rev. 21
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising