How to program a Switch2 to use a PROXIMITY KP Keypad

How to program a Switch2 to use a PROXIMITY KP Keypad
Switch2
AN1069
How to program a Switch2 to use a PROXIMITY KP
Keypad
What is a Switch2 system?
A Switch2 system is a step up in security and
versatility from the compact range. Still operating
as a standalone system it uses a control unit that is
separate from the user interface; a simple data cable
linking them together. This means that the control
unit can be mounted on the 'safe' side of the door
with only the keypad or reader outside.
A Switch2 control unit can be used with any of the
readers in the Paxton range. It has inputs for a door
contact and an exit button and has an output for an
alarm sounder. Lock control is via a volt free relay
which can be wired to operate fail closed and fail
open locks.
Initialising the keypad
When the system is powered up for the first time the keypad will beep 3 times a second. This indicates that
the keypad is waiting to be initialised. The red LED will be steady, the amber LED will flash slowly and the
green LED will flash quickly.
Enter your chosen 6 digit programming code and press the bell button (The green LED will flash faster still)
Confirm your programming code by entering the same 6 digit code and pressing the bell button (The green
LED goes out and the unit will acknowledge that the programming code has been accepted by beeping
twice after a short pause. All the LED's are now on)
NOTE: The programming code should NOT contain the sequence of numbers 1234, as this is the default user
code for unlocking the door.
The keypad has a default user code of 1234. The programming code you just entered will now let you into
the menu where additional alterations can be made.
1
Switch2
AN1069
Card plus Code
The KP reader must first be initialised as a TOUCHLOCK keypad. (as above)
Next, put the keypad into 'Card plus code' mode by keying in the following sequence.
Enter 6 digit Programming
Code
1
2
Hold down for 3 secs
Card plus Code
A PROXIMITY card pack must now be enrolled by simply presenting the PROXIMITY enrolment card to the
reader. All of the cards in the pack will now be valid.
4 digit user codes are entered using the TOUCHLOCK programming chart. If more than one user code is to
be used, activate 'Multiple codes' before programming the user codes.
Entry will now be granted with the presentation of any valid card followed by any valid user code.
Card or Code
Card or Code' mode is programmed in the same way as 'Card plus Code' except for using the following
program sequence to set up 'Card or Code'.
Enter 6 digit Programming
Code
1
3
Hold down for 3 secs
Card or Code
Entry now requires the presentation of a card or by entering a valid user code.
2
Switch2
AN1069
Card plus PIN
The KP reader must first be initialised as a TOUCHLOCK keypad.
Next, put the keypad into 'Card plus PIN' mode by keying in the following sequence.
1
1
Hold down for 3 secs
Card plus PIN
Enter 6 digit Programming
Code
A PROXIMITY card pack must now be enrolled by simply presenting the PROXIMITY enrolment card to the
reader.
Entry now requires the presentation of a valid card followed by its related user PIN.
4 digit PIN's are assigned as follows.
To assign a PIN to a card:
Present the enrolment card to the keypad; the reader will start to beep and the
amber LED will flash
Present the user card, the amber and green LED's will flash
Enter the PIN number to be associated with the user card (Maximum 4 digits)
Press the bell button, the LED's will flash faster
Enter the PIN again to confirm
Press the bell button
The user card and related PIN are now valid. When the user card is presented at the keypad the amber LED
will light indicating that the keypad is waiting for the PIN. When the correct PIN is entered the door will open.
A User card must have a PIN assigned to be active.
3
Switch2
AN1069
TOUCHLOCK programming guide
START - Enter the 6 digit Programming Code and hold down a function key for 3
seconds. - The unit beeps and the LED flashes faster.
Continue the key sequence to set the option - The keypad returns to operating mode.
Set a user
code
8
Combined Card and
Keypad modes
Re-enter user
code
Enter user code 4-8
digits
1
1
2
OR
Card
plus
PIN
OR
Card
or
Code
Card
plus
Code
= Normal
OR
6
= Toggle
OR
8
= Duress
OR
2
= Delete
Enter time in seconds (default =
07, max = 60)
Door open time
(seconds)
5
X
Single or multiple codes
2
2
One code only
Silent operation
3
2
20 wrong keystrokes
= 60 second lockout
4
Exit Button
X
3
4
OR
6
Multiple codes allowed
Beep on
OR
6
Silent
2
OFF
OR
6
ON
7
2
Open door for time
in option 5
OR
4
Change Programming
Code
6
Enter 6 digit
Programming
Code
Data Reset (except
Programming code)
9
Enter 6 digit
Programming Code
Toggle door open until
pressed again or toggle
code entered
Re-enter 6 digit
Programming Code
9
Function keys
= Hold down for 3 secs
For further information about programming user codes etc. please see: AN1004 - How to
program a Switch2 with TOUCHLOCK. < http://paxton.info/15 >
4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising