Installation of Bluetooth devices in custo

Installation of Bluetooth devices in custo
Quick Guide
Installation of Bluetooth devices in custo diagnostic 4.0
custo med devices with Bluetooth interface
12-channel PC ECG:
Holter ECG recorder:
custo cardio 100/110, custo cardio 200
custo flash 110/220, custo cor
Overview: 5 steps for Bluetooth connection
Precondition:
custo diagnostic is installed on your PC and ready for operation.
The custo med devices and components may only be connected to the PC after
custo diagnostic has been installed. The required device drivers are installed
using the custo diagnostic standard setup or via targeted selection during the custo
diagnostic setup.
Note on Bluetooth USB stick
The supplied Bluetooth USB stick is supported by Windows XP and Windows 7, but
not by Windows 2000 and Windows Vista.
To ensure the smooth installation of the supplied Bluetooth USB stick in
WINDOWS XP, the full installation of the current custo diagnostic version (not
the update) must be carried out from the CD, even if another version of custo diagnostic is already installed. Otherwise, the operating system will need to be accessed
manually. The custo diagnostic installation must be completed before connecting
the Bluetooth USB stick to the PC.
For WINDOWS 7, no subsequent installation of custo diagnostic or additional
access is required as the Bluetooth USB stick is already known in the operating
system.
1.
Connecting the Bluetooth USB stick to the PC
2.
Installing the Bluetooth USB stick driver
3.
Checking the driver installation
4.
Configuring the interface in custo diagnostic
5.
Allocating the device to the examination
www.customed.de | KAZ 0054 – DK 1213 | Version 001 – 01/25/2012
Page 01
Quick Guide
Installation of Bluetooth devices in custo diagnostic 4.0
Step 1
Connect Bluetooth-USB-Stick to the PC
Connect the Bluetooth USB stick to the PC. The driver installation for the new hardware ist started automatically.
Step 2
Installing the Bluetooth USB stick driver
WINDOWS XP:
Make sure that the option Install software automatically is selected in the first window of the driver installation. You can navigate through the installation procedure
using the buttons Next and Finish.
When the driver installation is completed the following message is displayed: “The
new hardware has been installed and is ready to use”.
WINDOWS 7:
The driver is installed automatically. Wait until the installation is complete (Message: “The device is ready to use”).
www.customed.de | KAZ 0054 – DK 1213 | Version 001 – 01/25/2012
Page 02
Quick Guide
Installation of Bluetooth devices in custo diagnostic 4.0
Step 3
Checking the driver installation
Check in the device manager if the Bluetooth driver has been installed correctly.
Proceed as follows:
Right-click on the My Computer icon on your desktop. Select the tab Manage in
the context menu.
Click on Device Manager in the left half of the window.
Open the item Bluetooth Radios in the right half of the window.
Here, the items Generic Blueooth Radio (CSR Bluetooth Radio) and Microsoft Bluetooth Enumerator should be displayed.
www.customed.de | KAZ 0054 – DK 1213 | Version 001 – 01/25/2012
Page 03
Quick Guide
Installation of Bluetooth devices in custo diagnostic 4.0
Step 4
Configuring the interface in custo diagnostic
Start custo diagnostic.
Open the page Examination, Settings, Connection, Device
.
Select the device you wish to connect via Bluetooth from the selection list: ECG,
cardio 100 / cardio 200 or Bluetooth, i.s. medical band-flash . The item i.s. medical
band-flash represents the holter ECG recorders (custo flash 110, custo flash 220,
custo cor). Select the device by clicking on the device name.
Select Autom. BT-COM search
in the selection list Interface.
Click Save to apply your entries.
Then, open the page:
Examination, Settings, Connection, i.s. medical band
Enable the item Microsoft Stack
open .
.
, click Save (bottom left of the monitor) and then
Besides to the right the message “Interface is enabled!”
is displayed.
Switch on the Bluetooth device (not necessary for custo cardio 200).
Click on the Search button . The dialogue “i.s. medical band Search” appears. Restart the search (New Search ) if the device has not been found. Select the desired
device from the list by double-clicking or select the device using the cursor and
click on the Confirm button .
The selected device is displayed in the table on the page i.s. medical band
Save your entries.
.
To establish the Bluetooth connection double-click on the device name in the table
. Change to the tab Connection in the open dialogue and click Connect .
After the connection has been established the message “Serial connection is enabled! End” is displayed. Click End to close the dialogue.
Save your entries and close the page i.s. medical band by clicking the End button.
Restart the programme to apply the changed parameters in the configuration
database.
www.customed.de | KAZ 0054 – DK 1213 | Version 001 – 01/25/2012
Page 04
Quick Guide
Installation of Bluetooth devices in custo diagnostic 4.0
www.customed.de | KAZ 0054 – DK 1213 | Version 001 – 01/25/2012
Page 05
Quick Guide
Installation of Bluetooth devices in custo diagnostic 4.0
Step 5
Allocating the device to the examination
ECG devices
custo cardio 100/110 and custo cardio 200
Open the page
Examination, Resting ECG, Settings, Connection, Device
Examination, Stress ECG, Settings, Connection, Device
Select your ECG device,
e.g. cardio 100 or cardio 200
Click Save
or
.
to apply your entries.
Start a recording to test the function of the connection.
Holter ECG recorder
custo flash 110, custo flash 220, custo cor
Open the page
Examination, Holter, Settings, Connection, Device
Note: custo flash 110 is displayed on this page only if the medical practice
is connected (holter online) and custo diagnostic is configured accordingly.
Activate your recorder under “Holter Recorder” by clicking
the respective checkbox . Select the item i.s. medical band - flash
in the respective selection list “Interface”.
Note: In addition to the Bluetooth connection the connection to the card reader
(USB device) can be enabled for holter ECG recorders, see next page.
Click Save
to apply your entries.
Start a recording to test the function of the connection.
www.customed.de | KAZ 0054 – DK 1213 | Version 001 – 01/25/2012
Page 06
Quick Guide
Installation of Bluetooth devices in custo diagnostic 4.0
www.customed.de | KAZ 0054 – DK 1213 | Version 001 – 01/25/2012
Page 07
Quick Guide
Installation of Bluetooth devices in custo diagnostic 4.0
Addition for holter ECG recorders
Enabling connection to USB card reader
Connect the supplied USB card reader to the PC. The driver is installed automatically.
Wait until the installation is complete.
Configuring the USB card reader in custo diagnostic
Start custo diagnostic and open the page:
Examination, Holter ECG, Settings, Connection, Device
custo flash 110, custo flash 220, custo cor:
Activate flash card
Select the drive of the USB card reader. To do this, click on the ... button at the
end of the line “Directory”. Select the corresponding drive in the directory structure
and confirm by clicking OK.
Click Save to apply your entries.
The USB card reader is ready for operation.
www.customed.de | KAZ 0054 – DK 1213 | Version 001 – 01/25/2012
Page 08
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising