57832 Iss 2 B5 FP730 English
FP730 series
ti pr
Important – UK only
before using your Kenwood appliance
Read these instructions carefully and retain for future reference.
Remove all packaging and any labels.
The blades and discs are very sharp, handle
with care. Always hold the knife blade
by the finger grip
at the top, away
from the cutting edge, both when
handling and cleaning.
Do not lift or carry the processor by the handle - or the handle
may break resulting in injury.
Always remove the knife blade before pouring contents from the
Keep hands and utensils out of the processor bowl and liquidiser
jug whilst connected to the power supply.
Switch off and unplug:
● before fitting or removing parts
● after use
● before cleaning
Never use your fingers to push food down the feed tube. Always
use the pusher/s supplied.
Before removing the lid from the bowl or liquidiser/mill from the
power unit:● switch off;
● wait until the attachment/blades have completely stopped;
● be careful not to unscrew the liquidiser jug or mill from the
blade unit.
Liquids should be allowed to cool to room temperature before
Do not use the lid to operate the processor, always use the on/off
speed control.
This machine will be damaged and may cause injury
if the interlock mechanism is subjected to excessive
Never use an unauthorised attachment.
Never leave the machine on unattended.
Never use a damaged machine. Get it checked or repaired: see
Never let the power unit, cord or plug get wet.
Don’t let excess cord hang over the edge of a table or worktop
or touch hot surfaces.
Do not exceed the maximum capacities stated in the
recommended speed chart.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do not play
with the appliance.
Only use the appliance for its intended domestic use. Kenwood
will not accept any liability if the appliance is subject to improper
use, or failure to comply with these instructions.
Misuse of your processor/liquidiser can result in injury.
For non-rewireable plugs the fuse cover MUST be refitted when
replacing the fuse. If the fuse cover is lost then the plug must not
be used until a replacement can be obtained. The correct fuse
cover is identified by colour and a replacement may be obtained
from your Kenwood Authorised Repairer (see Service).
If a non-rewireable plug is cut off it must be DESTROYED
IMMEDIATELY. An electric shock hazard may arise if an
unwanted non-rewireable pug is inadvertently inserted into a 13A
socket outlet.
This appliance conforms to EC directive 2004/108/EC on
Electromagnetic Compatibility and EC regulation no. 1935/2004
of 27/10/2004 on materials intended for contact with food.
before using for the first time
1 Remove all packaging including the plastic blade covers from the
knife blade. Take care the blades are very sharp. These
covers should be discarded as they are to protect the blade
during manufacture and transit only.
2 Wash the parts see ‘cleaning’
3 Push excess cord into the back of the machine.
power unit
detachable drive shaft
feed tube
safety interlocks
cord storage
speed control
Refer to the relevant section under “using the attachments” for
additional safety warnings for each individual attachment.
The wires in the cord are coloured as follows:
Blue = Neutral,
Brown = Live.
The appliance must be protected by a 13A approved (BS1362)
before plugging in
Make sure your electricity supply is the same as the one shown
on the underside of your machine.
filler cap
sealing ring
blade unit
additional attachments
Not all of the attachments listed below may be included with
your food processor. Attachments are dependent upon the
model variant.
knife blade
dough tool
twin beater geared metal whisk
maxi-blend canopy
thick slicing/coarse shredding disc
thin slicing/fine shredding disc
fine (Julienne style) chipper disc
geared citrus press
mini processor bowl
centrifugal juicer
KENSTORE™ attachments carousel
recipe book
choosing a speed for all functions
Maximum Capacities
Knife Blade
One Stage Cake Mix
Pastry - rubbing fat into flour
Adding water to combine pastry ingredients
1.5Kg/3lb 5oz Total Wt
340g/12oz Flour Wt
600g/1lb 6oz Meat
Knife Blade with maxi-blend canopy
Soups – start at a low speed and move up to 8
1.5 litres/2pts 12fl. oz
Egg Whites
Egg & sugar for fatless sponges
6 Egg Whites
500 mls
Dough tool
Yeasted mixes
500g/1lb 2oz
Discs – slicing/shredding/chipping
Firm food items such as carrots, hard cheese.
Softer items such as cucumbers, tomatoes
Citrus Press
Citrus fruits
Mini Bowl & knife
All processing
All processing
1.5 litres/2pts 12fl.oz
All processing
Centrifugal juicer
Fruit & Vegetables
to use your food processor
using the attachments
1 Fit the detachable shaft onto the power unit .
2 Then fit the bowl. Place the handle towards the back and turn
clockwise until it locks .
3 Fit an attachment over the drive shaft.
● Always fit the bowl and attachment onto the machine before
adding ingredients.
4 Fit the lid - ensuring the top of the drive shaft locates into the
centre of the lid.
● Do not use the lid to operate the processor, always
use the on/off control.
5 Switch on and select a speed.
● The processor won’t work if the bowl and lid are fitted
● Use the pulse (P) for short bursts. The pulse will operate for as
long as the control is held in position.
6 Reverse the above procedure to remove the lid, attachments and
● Always switch off before removing the lid.
knife blade/ dough tool
The knife blade is the most versatile of all
the attachments. The length of the
processing time will determine the texture
achieved. For coarser textures use the
pulse control.
Use the knife blade for cake and pastry
making, chopping raw and cooked meat,
vegetables, nuts, pate, dips, pureeing
soups and to also make crumbs from
biscuits and bread. It can also be used for
yeasted dough mixes if the dough tool is
not supplied.
Your processor is not suitable for crushing or grinding coffee
beans, or converting granulated sugar to caster sugar.
When adding almond essence or flavouring to mixtures avoid
contact with the plastic as this may result in permanent marking.
1 Fit the sealing ring into the blade unit - ensuring the seal is
located correctly. Leaking will occur if the seal is
damaged or not fitted correctly.
2 Screw the jug onto the blade unit.
3 Put your ingredients into the jug.
4 Put the filler cap in the lid, then turn.
5 Turn the lid in a clockwise direction to lock onto the jug.
6 Place the liquidiser onto the power unit and turn to lock .
7 Select a speed or use the pulse control.
● Allow all liquids to cool to room temperature before
placing them in the liquidiser.
Use the dough tool for yeasted mixes.
to use your liquidiser
knife blade
Cut food such as meat, bread, vegetables
into cubes approximately 2cm/3⁄4in before
Biscuits should be broken into pieces and added down the feed
tube whilst the machine is running.
When making pastry use fat straight from the fridge cut into
Take care not to over-process.
dough tool
Place the dry ingredients in the bowl and add the liquid down the
feed tube whilst the machine is running. Process until a smooth
elastic ball of dough is formed this will take 60 - 90 secs.
Re-knead by hand only. Re-kneading in the bowl is not
recommended as it may cause the processor to become unstable.
twin beater geared whisk
Use for light mixtures only eg egg whites, cream, evaporated milk
and for whisking eggs and sugar for fatless sponges. Heavier
mixtures such as fat and flour will damage it.
using the whisk
When making mayonnaise, put all the ingredients, except the oil into
the liquidiser. Then with the machine running, pour the oil into the
filler cap and let it run through.
Thick mixtures, eg pates and dips, may need scraping down. If it’s
difficult to process, add more liquid.
When crushing ice use the pulse in short bursts.
To ensure the long life of your liquidiser, never run it for longer than
60 seconds. Switch off as soon as you’ve got the right consistency.
Don’t process spices - they may damage the plastic.
The machine won’t work if the liquidiser is fitted incorrectly.
Don’t put dry ingredients into the liquidiser before switching on. If
necessary, cut them into pieces; remove the filler cap; then with
the machine running, drop them through one by one.
Don’t use the liquidiser as a storage container. Keep it empty
before and after use.
Never blend more than 11⁄2 litres (2pts 12floz) - less for frothy
liquids like milkshakes.
1 Fit the drive shaft and bowl onto the power unit.
2 Push each beater securely into the drive
3 Fit the whisk by carefully turning until it
drops over the drive shaft.
4 Add the ingredients.
5 Fit the lid - ensuring the end of the shaft
locates into the centre of the lid.
6 Switch on.
● The whisk is not suitable for making onestage cakes or creaming fat and sugar as
these mixes will damage it. Always use the
knife blade for cake making.
Best results are obtained when the eggs are at room temperature.
Ensure the bowl and whisks are clean and free from grease before
maxi-blend canopy
When blending liquids, use the maxi-blend
canopy with the knife blade. It allows you
to increase the liquid processing capacity
from 1 litre to 1.5 litres, prevents leaking
and improves the chopping performance
of the blade.
1 Fit the drive shaft and bowl onto the
power unit.
2 Fit the knife blade.
3 Add ingredients to be processed.
4 Fit the canopy over the top of the blade
ensuring it sits on the ledge inside the bowl
. Do not push down on the
canopy, hold by the centre grip.
5 Fit the lid and switch on.
Use fresh ingredients
Don’t cut food too small. Fill the width of the large feed tube
fairly full. This prevents the food from slipping sideways during
processing. Alternatively use the small feed tube.
When using the chipper disc, place ingredients horizontally.
When slicing or shredding: food placed upright
comes out
shorter than food placed horizontally
There will always be a small amount of waste on the plate or in
the bowl after processing.
slicing/shredding discs
reversible slicing/shredding
discs - thick , thin Use the shredding side for cheese,
carrots, potatoes and foods of a similar
Use the slicing side for cheese, carrots,
potatoes, cabbage, cucumber,
courgette, beetroot and onions.
fine (Julienne style) chipper disc
ti pr
Use to cut: potatoes for Julienne style
French fries; firm ingredients for salads,
garnishes, casseroles and stir fries (eg
carrot, swede, courgette, cucumber).
citrus press
Use the citrus press to squeeze
the juice from citrus fruits (eg
oranges, lemons, limes and
ti pr
Never remove the lid until the cutting disc has
completely stopped.
Handle the cutting discs with care - they are
extremely sharp
to use the citrus
to use the cutting discs
1 Fit the drive shaft and bowl
onto the power unit.
2 Fit the sieve into the bowl ensuring the sieve handle is
locked into position directly over
the bowl handle
3 Place the cone over the drive
shaft turning until it drops all the way down
4 Cut the fruit in half. Then switch on and press the fruit onto the
● The citrus press will not operate if the sieve is not
locked correctly.
1 Fit the drive shaft and bowl onto the
power unit.
2 Holding by the centre grip
, place
the disc onto the drive shaft with the
appropriate side uppermost
3 Fit the lid.
4 Choose which size feed tube you
want to use. The pusher contains a
smaller feed tube for processing
individual items or thin ingredients.
To use the small feed tube - first put
the large pusher inside the feed tube.
To use the large feed tube - use both
pushers together.
5 Put the food in the feed tube.
6 Switch on and push down evenly with the pusher - never put
your fingers in the feed tube.
Use the mill for milling herbs, nuts and
coffee beans.
blade unit
sealing ring
sprinkler lid
mini processor bowl
Use the mini processor bowl to
chop herbs and process small
quantities of ingredients e.g.
meat, onion, nuts, mayonnaise,
vegetables, purées, sauces
and baby food.
mini processor knife blade
mini processor bowl
Never fit the blade unit to your machine
without the jar fitted.
Never unscrew the jar while the mill is fitted to
your machine.
Don’t touch the sharp blades. Keep the
blade unit away from children.
Never remove the mill until the blades have
completely stopped.
To ensure long life of your mill, never run for
longer than 30 seconds. Switch off as soon as
you’ve got the right consistency.
Don’t process spices - they may damage the
The machine won’t work if the mill is fitted
Use for dry ingredients only.
to use the mini
processor bowl
1 Fit the drive shaft and bowl
onto the power unit.
2 Fit the mini processor bowl ensuring the ribs on the inside
of the mini bowl chimney align
with the slots in the main bowl
3 Place the knife blade over the
drive shaft
4 Add the ingredients to be
5 Fit the lid and switch on.
to use your mill
1 Put your ingredients into the jar. Fill it
no more than half full.
2 Fit the sealing ring into the blade unit.
3 Turn the blade unit upside down.
Lower it into the jar, blades down.
4 Screw the blade unit onto the jar until
it is finger tight.
5 Place the mill onto the power unit
and turn to lock
6 Switch on to maximum speed or use
the pulse control.
7 After milling, you can replace the
blade unit with the sprinkler lid and
shake out your food.
● The sprinkler lid is not airtight.
ti pr
Herbs are best milled when clean and dry.
ti pr
Never remove the lid until the knife blade has completely
The knife blade is very sharp - always handle with care.
Don’t process spices – they may damage the plastic.
Don’t process hard food such as coffee beans, ice cubes or
chocolate – they may damage the blade.
Herbs are best chopped when clean and dry.
Always add a little liquid when blending cooked ingredients to
make baby food.
Cut foods such as meat, bread, vegetables into cubes
approximately 1-2 cm (1⁄2 – 3⁄4 in) before processing.
When making mayonnaise add the oil down the feed tube.
centrifugal juicer
KENSTORE™ attachments carousel
Use the centrifugal juice for making
juice from firm fruit and vegetables.
inner bowl
Your food processor is supplied with an attachment storage
carousel that fits inside the bowl.
to use the storage carousel
1 Fit the knife blade to the bowl.
2 Then fit the whisk, discs and canopy into the carousel .
3 Fit the carousel over the knife blade and place the processor lid
on top .
to use the centrifugal
1 Fit the drive shaft and bowl onto the
power unit.
2 Lock the strainer into the inner bowl
3 Fit the inner bowl into the processor
4 Place the attachment lid onto the bowl,
turn until it locks and the feed tube sits
over the handle
5 Cut the food into small pieces to fit the
feed tube.
6 Switch on and push down evenly with
the pusher - never put your
fingers in the feed tube. Process
fully before adding more.
7 After adding the last piece, let the
machine run for a further 20 seconds
to extract all the juice from the strainer.
ti pr
If the processor vibrates, switch off and empty the strainer (The
processor vibrates if the pulp becomes unevenly distributed).
Process small amounts at a time (450g maximum) and empty
the strainer and inner bowl regularly.
Before processing remove stones and pips (eg pepper, melon,
plum) and tough skins (eg melon, pineapple). You don’t need to
peel or core apples and pears.
care & cleaning
Use firm, fresh fruit and vegetables.
Citrus juice will be bitter and frothy because its peel and pith get
processed too. Use the citrus juicer instead.
Always switch off and unplug before cleaning.
Handle the blades and cutting discs with care - they are
extremely sharp.
Some foods may discolour the plastic. This is perfectly normal
and won’t harm the plastic or affect the flavour of your food. Rub
with a cloth dipped in vegetable oil to remove the discolouration.
power unit
Wipe with a damp cloth, then dry.
Ensure that the interlock area is
clear of food debris.
Store excess cord in the storage
area at the back of the
Empty the jug/jar before unscrewing it from the blade unit.
Wash the jug/jar by hand.
Remove and wash the seals.
Don’t touch the sharp blades – brush them clean using hot
soapy water, then rinse thoroughly under the tap. Don’t
immerse the blade unit in water.
5 Leave to dry upside down.
At the end of its working life, the product must not be disposed of as
urban waste.
It must be taken to a special local authority differentiated waste
collection centre or to a dealer providing this service.
Disposing of a household appliance separately avoids possible
negative consequences for the environment and health deriving
from inappropriate disposal and enables the constituent materials
to be recovered to obtain significant savings in energy and
resources. As a reminder of the need to dispose of household
appliances separately, the product is marked with a crossed-out
wheeled dustbin.
twin beater geared whisk
Detach the beaters from the drive head by gently pulling them
free. Wash in warm soapy water.
Wipe the drive head with a damp cloth, then dry.
Do not immerse the drive head in water.
all other parts
Wash by hand, then dry.
Alternatively they can be washed on the top rack of your
dishwasher. A short low temperature programme is
service & customer care
If the cord is damaged it must, for safety reasons, be replaced
by Kenwood or an authorised Kenwood repairer.
If you need help with:
● Using your machine
● Servicing or repairs (in or out of guarantee)
call Kenwood on 023 92392333 and ask for customer care.
Have your model number ready - it’s on the underside of
the processor.
● spares and attachments
call 0870 2413653.
other countries
Contact the shop where you brought the food processor.
Designed and engineered by Kenwood in the UK
Made in China
guarantee UK only
If your food processor goes wrong within one year from the date
you bought it, we will repair or replace it free of charge provided:
you have not misused, neglected, or damaged it;
it has not been modified (unless by Kenwood);
it is not second hand;
it has not been used commercially;
you have not fitted a plug incorrectly; and
you supply your receipt to show when you bought it.
This guarantee does not affect your statutory rights.
shortcrust pastry
victoria sandwich
150g (6oz) Soft margarine
150g (6oz) caster sugar
150g (6oz) self raising flour
5mls (1tsp) baking powder
3 eggs
15mls (1tbsp) warm water
filling & decoration
3tbsp strawberry jam
150mls (1⁄4pt) double cream whipped (optional)
1tbsp icing sugar or caster sugar
300g (12oz) plain flour
150g (6oz) mixture of lard and margarine cut into small pieces
2.5 mls (1⁄2 tsp) salt
45mls (3tbsp) cold water
1 Fit the knife blade and add the flour, salt and fat. Process for
approximately 10 seconds or until the mixture looks like coarse
2 Then add the water down the feed tube until the mixture looks
like it is about to stick together.
3 Turn out the mixture onto a worksurface and shape by hand.
Use as required.
● For best results allow the pastry to rest before use. Place in a
plastic bag or wrap in clingfilm and chill in the fridge for 20
1 Pre-heat the oven to 180°C/350°F/Gas mark 4 and grease two
18cm(7”) shallow cake tins.
2 Fit the knife blade. Place all the ingredients for the sponge in the
bowl and process for 5 seconds. Using a spatula, scrape the
mixture into the centre of the bowl and process for a further 5
3 Pour the mixture into the prepared tins and bake for 20-25
minutes or until firm to a light touch and coming away from the
edges slightly. If you are unsure whether the cake is cooked
insert a thin skewer in the centre and it should come out clean.
Turn out onto a wire cooling rack.
4 When cool spread the jam and cream over one of the cakes,
top with the other cake and sprinkle with the sugar.
4 egg whites
200g (8oz) caster sugar
1 Whisk the egg whites until stiff.
2 Add half the sugar and continue to whisk until the mixture is
3 Remove the whisk and carefully fold in the remaining sugar with
a metal spoon.
4 Pipe the mixture onto trays lined with non-stick baking paper.
5 Bake in a pre-heated oven at 110°C/225°F/Gas mark 1⁄4 for
about 4 - 5hours until firm and crisp. If they start to brown, leave
the door slightly ajar.
fruit cake
125g (5oz) block margarine (cut into cubes)
125g (5oz) caster sugar
2 eggs
80 - 100mls (5-6tbsp) milk
275g (11oz) mixed fruit
200g (8oz) self raising flour
5mls (1tsp) mixed spice
300g (12oz) braising steak, cubed.
400g can of tomatoes
30mls (2tbsp) tomato puree
1 onion
5mls (1tsp) basil
100g (4oz) lasagne
200g (8oz) mozzarella cheese
15mls (1tbsp) oil
salt and pepper
1 Fit the knife blade and place the cubed margarine and sugar in
the bowl.
2 Mix until smooth, light and fluffy, scraping down as necessary.
3 Add the eggs one at a time.
4 Add the flour, spices and milk. Pulse until ingredients combined.
5 Add the fruit using the pulse.
6 Pour the mixture into a greased and lined 7”/18cm round cake
tin. Bake in a preheated oven 150°C/300°F/Gas Mark 2 for
approximately 2 hours or until cooked. Turn out of the tin when
1 Grate the cheese using the shredding disc.
2 Then separately chop the meat and onions with the knife blade.
3 Pre-heat the oil and fry the onions until softened, add the meat
and fry until brown.
4 Then add the tomatoes, tomato puree and seasonings.
5 Stir well, cover and simmer gently for about 40minutes.
6 Cook the lasagne in plenty of salted boiling water until tender.
Then drain well.
7 Place layers of meat, lasagne and cheese in a 1litre/2pint oven
proof dish. Finish with a layer of cheese.
8 Bake at 190°C/375°F/Gas Mark 5 for 30minutes or until golden
and bubbling.
whisked sponge
3 eggs
75g/3oz caster sugar
75g/3oz plain flour (sieved twice)
1 Fit the twin beater geared whisk and add the sugar and eggs
into the bowl.
2 Whisk until the mixture is thick and leaves a trail.
3 Fold the flour in carefully by hand using a metal spoon.
4 Pour the mixture into a deep lined and greased 7”/18cm cake
tin. Bake in a preheated oven at 190°C/375°F/Gas Mark 5 for
approximately 25minutes or until the cake springs back when
5 Remove from the tin and cool on a wire rack.
white bread
500g(1lb 2oz) strong white bread flour
5mls (1tsp) salt
15g(1⁄2oz) lard
15g (1⁄2oz) fresh yeast or 10mls(2tsp) dried yeast + 5mls (1tsp)
caster sugar.
300mls (11fl oz) warm water, 100mls (31⁄2 fl oz) boiling water to
200mls (71⁄2 fl oz) cold water
1 Dried yeast (the type that needs reconstituting): Add
the yeast and sugar to the warm water. Leave to stand for 5 - 10
minutes until frothy.
Fresh yeast: crumble into the flour
Other types of yeast: follow the manufacturer’s instructions.
2 Fit the dough tool or knife blade and add the flour (with fresh
yeast if used), salt and lard. Process for a few seconds to evenly
distribute the ingredients.
3 Then with the motor running quickly pour the liquid in a steady
stream down the feed tube until the mixture forms an elastic soft
dough. This will take about 60 - 90 seconds.
4 Remove the dough, place in a bowl, cover with an oiled piece of
clingfilm or a plastic bag, and leave in a warm place for 45 - 60
minutes or until doubled in size.
5 Re-knead by hand for 2 - 3 minute. Re-kneading in the
bowl is not recommended as it may cause the
processor to become unstable. Shape into a loaf or 15
rolls and place on greased baking trays and leave until double in
6 Then bake in a pre-heated oven at 230°C/450°F/Gas mark 8 for
20 - 25 minutes for the loaf or 10 - 15 minutes for bread rolls.
When ready they should sound hollow when tapped on the
carrot and coriander soup
25g (1oz) butter
1 onion chopped
1 clove garlic crushed
700g (1lb 10oz) carrot cut into 1 cm cubes
cold chicken stock
10-15ml (2-3tsp) ground coriander
salt and pepper
1 Melt the butter in a pan, add the onion and garlic and fry until
2 Place the carrot into the liquidiser, add the onion and garlic. Add
sufficient stock to reach the 1.5L level marked on the goblet. Fit
the lid and filler cap.
3 Blend on maximum speed for 5 seconds for a coarse soup or
longer for a finer result.
4 Transfer the mixture to a saucepan, add the coriander and
seasoning and simmer the soup for 30 to 35 minutes or until
5 Adjust the seasoning as necessary and add extra liquid if
Head Office Address: Kenwood Limited, New Lane, Havant, Hampshire PO9 2NH, UK
Designed and engineered by Kenwood in the UK
Made in China
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF