CPU 1515SP PC (F)

CPU 1515SP PC (F)
___________________
Preface
1
___________________
Documentation guide
SIMATIC
ET 200SP Open Controller
CPU 1515SP PC (F)
Manual
2
___________________
Safety notes
3
___________________
Product overview
4
___________________
Installing
5
___________________
Connection
Diagnostics, error and
6
___________________
system alarm
___________________
7
Commissioning
___________________
8
Functions
___________________
9
Maintenance
___________________
10
Technical data
___________________
A
Accessories/spare parts
___________________
B
Abbreviations
___________________
C
Troubleshooting
05/2017
A5E32701806-AC
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Division Digital Factory
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E32701806-AC
Ⓟ 04/2017 Subject to change
Copyright © Siemens AG 2014 - 2017.
All rights reserved
Preface
Purpose of the documentation
This manual supplements the system manual for the ET 200SP distributed I/O system.
Functions that generally relate to the system are described in this manual.
The information contained in this product manual and the system / function manuals enable
you put the CPU 1515SP PC (F) into operation.
Basic knowledge required
The system must be operated and used by qualified staff only.
The following knowledge is required:
● Installation guideline for SIMATIC ET 200SP
● Programming with STEP 7
● PC based automation with an S7-1500 software controller and with
WinCC Runtime Advanced
● Basic knowledge of PC technology
● Windows Embedded Standard 7 operating system
Scope of validity of the documentation
This documentation is valid for the following devices:
ET 200SP Open Controller
Article number
System version
WES7 E 32Bit 4GB RAM
System version
WES7 P 64Bit 4GB RAM
6ES7677-2AA31-0EB0
6ES7677-2AA41-0FB0
CPU 1515SP PC + HMI 128PT
--
6ES7677-2AA41-0FK0
CPU 1515SP PC + HMI 512PT
--
6ES7677-2AA41-0FL0
CPU 1515SP PC + HMI 2048PT
--
6ES7677-2AA41-0FM0
CPU 1515SP PC
CPU 1515SP PC F
6ES7677-2FA31-0EB0
6ES7677-2FA41-0FB0
CPU 1515SP PC F + HMI 128PT
--
6ES7677-2FA41-0FK0
CPU 1515SP PC F + HMI 512PT
--
6ES7677-2FA41-0FL0
CPU 1515SP PC F + HMI 2048PT
--
6ES7677-2FA41-0FM0
CPU 1515SP PC,
spare part, without CFast card, without software
6ES7677-2AA40-0AA0
CPU 1515SP PC (F)
4
Manual, 05/2017, A5E32701806-AC
Preface
Conventions
Conventions STEP 7: In this documentation, "STEP 7" is used as a synonym for all versions
of the configuration and programming software "STEP 7 (TIA Portal)".
Please also observe notes marked as follows:
Note
A note contains important information on the product described in the documentation, on the
handling of the product or on the section of the documentation to which particular attention
should be paid.
Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions only form one element of such a concept.
Customer is responsible to prevent unauthorized access to its plants, systems, machines
and networks. Systems, machines and components should only be connected to the
enterprise network or the internet if and to the extent necessary and with appropriate security
measures (e.g. use of firewalls and network segmentation) in place.
Additionally, Siemens’ guidance on appropriate security measures should be taken into
account. For more information about industrial security, please visit
(http://www.siemens.com/industrialsecurity).
Siemens’ products and solutions undergo continuous development to make them more
secure. Siemens strongly recommends to apply product updates as soon as available and to
always use the latest product versions. Use of product versions that are no longer supported,
and failure to apply latest updates may increase customer’s exposure to cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed under (http://www.siemens.com/industrialsecurity).
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
5
Preface
Siemens Industry Online Support
You can find current information on the following topics quickly and easily here:
● Product support
All the information and extensive know-how on your product, technical specifications,
FAQs, certificates, downloads, and manuals.
● Application examples
Tools and examples to solve your automation tasks – as well as function blocks,
performance information and videos.
● Services
Information about Industry Services, Field Services, Technical Support, spare parts and
training offers.
● Forums
For answers and solutions concerning automation technology.
● mySupport
Your personal working area in Industry Online Support for messages, support queries,
and configurable documents.
This information is provided by the Siemens Industry Online Support in the Internet
(http://www.siemens.com/automation/service&support).
Industry Mall
The Industry Mall is the catalog and order system of Siemens AG for automation and drive
solutions on the basis of Totally Integrated Automation (TIA) and Totally Integrated Power
(TIP).
Catalogs for all the products in automation and drives are available on the Internet
(https://mall.industry.siemens.com).
Information about third-party software updates
This product contains third-party software. Siemens accepts liability with respect to
updates/patches for the third-party software only when these are distributed by Siemens in
the context of a Software Update Service contract or officially approved by Siemens.
Otherwise, updates/patches are installed at the user's own risk. You can find more
information about our software update service offer under
(http://w3.siemens.com/mcms/topics/en/simatic/licenses/software-updateservice/Pages/Default.aspx).
Notes on protecting administrator accounts
A user with administrator rights has extensive access and manipulation possibilities.
Therefore, make sure that the administrator account is adequately protected to prevent
unauthorized changes. To do this, set secure passwords and use a standard user account
for regular operation. Other measures, such as the use of security policies, should be
applied as required.
CPU 1515SP PC (F)
6
Manual, 05/2017, A5E32701806-AC
Preface
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
7
Table of contents
Preface ................................................................................................................................................... 4
1
Documentation guide ............................................................................................................................ 11
1.1
2
Safety notes .......................................................................................................................................... 15
2.1
3
4
5
6
Documentation on CPU 1515SP PC (F) ................................................................................ 14
Notes on use .......................................................................................................................... 17
Product overview .................................................................................................................................. 18
3.1
Fail-safe option....................................................................................................................... 18
3.2
Properties ............................................................................................................................... 19
3.3
Sample configuration ............................................................................................................. 21
3.4
Components ........................................................................................................................... 23
3.5
Configuration of the devices .................................................................................................. 24
3.6
Operator controls and display elements ................................................................................ 25
3.7
3.7.1
3.7.2
3.7.3
Scope of delivery.................................................................................................................... 28
Unpacking the device ............................................................................................................. 28
Scope of delivery - System version WES7 E 32Bit 4GB RAM .............................................. 30
Scope of delivery - System version WES7 P 64Bit 4GB RAM .............................................. 32
Installing ............................................................................................................................................... 34
4.1
Basics ..................................................................................................................................... 34
4.2
Hardware configuration .......................................................................................................... 37
4.3
Installing CPU 1515SP PC (F) ............................................................................................... 38
Connection ........................................................................................................................................... 40
5.1
Notes on connection .............................................................................................................. 40
5.2
Terminal and block diagram................................................................................................... 41
5.3
Electrical configuration ........................................................................................................... 42
5.4
Connecting devices to networks ............................................................................................ 44
5.5
Securing cables...................................................................................................................... 44
Diagnostics, error and system alarm ..................................................................................................... 46
6.1
Status and error display ......................................................................................................... 46
CPU 1515SP PC (F)
8
Manual, 05/2017, A5E32701806-AC
Table of contents
7
8
9
Commissioning ..................................................................................................................................... 49
7.1
Notes on commissioning .........................................................................................................49
7.2
Initial commissioning ...............................................................................................................50
7.3
Initial configuration of an Open Controller ..............................................................................53
7.4
Installing license keys .............................................................................................................55
7.5
Windows Security Center .......................................................................................................57
7.6
Switching CPU 1515SP PC (F) on/off ....................................................................................58
Functions .............................................................................................................................................. 59
8.1
Monitoring functions ................................................................................................................59
8.2
Retentive memory NVRAM .....................................................................................................60
8.3
8.3.1
8.3.2
8.3.3
8.3.3.1
8.3.3.2
8.3.3.3
8.3.3.4
8.3.3.5
8.3.3.6
8.3.3.7
8.3.4
8.3.5
BIOS description .....................................................................................................................61
Introduction .............................................................................................................................61
Starting BIOS setup ................................................................................................................62
BIOS setup menus ..................................................................................................................63
Information menu ....................................................................................................................65
Main menu ..............................................................................................................................66
Advanced menu ......................................................................................................................67
Security menu .........................................................................................................................69
Power menu ............................................................................................................................70
Boot menu ...............................................................................................................................71
Exit menu ................................................................................................................................73
BIOS setup default settings ....................................................................................................74
BIOS update ...........................................................................................................................75
8.4
Power options .........................................................................................................................76
8.5
8.5.1
8.5.2
Protective functions for data carriers ......................................................................................77
Enhanced Write Filter (EWF) ..................................................................................................78
File-Based Write Filter (FBWF) ...............................................................................................82
Maintenance ......................................................................................................................................... 84
9.1
Backing up and restoring data ................................................................................................84
9.2
9.2.1
9.2.2
Change partitioning .................................................................................................................85
Partitions in the delivery state .................................................................................................85
Change partitioning .................................................................................................................86
9.3
Restoring the delivery state ....................................................................................................92
9.4
Restoring delivery state using USB stick ................................................................................95
9.5
Updating software ...................................................................................................................97
9.6
Windows Embedded Standard 7 ............................................................................................98
9.7
Sending the device to customer service .................................................................................99
9.8
Removing and inserting the CFast card ...............................................................................100
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
9
Table of contents
10
Technical data .....................................................................................................................................101
10.1
Standards and approvals ..................................................................................................... 101
10.2
Electromagnetic compatibility .............................................................................................. 105
10.3
Shipping and storage conditions .......................................................................................... 108
10.4
Mechanical and climatic ambient conditions ........................................................................ 108
10.5
Information on insulation, protection class, degree of protection and rated voltage ........... 110
10.6
Use of the ET 200SP in zone 2 potentially explosive atmospheres .................................... 111
10.7
10.7.1
10.7.2
10.7.3
10.7.4
10.7.5
10.7.6
10.7.7
10.7.8
Module data ......................................................................................................................... 112
CPU 1515SP PC, system version WES7 E 32Bit 4GB RAM .............................................. 112
CPU 1515SP PC F, system version WES7 E 32Bit 4GB RAM ........................................... 115
CPU 1515SP PC, system version WES7 E 32Bit 4GB RAM - spare part ........................... 118
CPU 1515SP PC, system version WES7 P 64Bit 4GB RAM .............................................. 121
CPU 1515SP PC F, system version WES7 P 64Bit 4GB RAM ........................................... 124
CPU 1515SP PC, system version WES7 E 64Bit 4GB RAM - spare part ........................... 127
CPU 1515SP PC (F) + HMI ................................................................................................. 130
S7-1500 Software Controller CPU 1505SP (F) ................................................................... 130
10.8
10.8.1
Dimension drawings ............................................................................................................. 131
CPU 1515SP PC (F) ............................................................................................................ 131
A
Accessories/spare parts .......................................................................................................................133
B
Abbreviations .......................................................................................................................................135
C
Troubleshooting ...................................................................................................................................137
Glossary ..............................................................................................................................................138
CPU 1515SP PC (F)
10
Manual, 05/2017, A5E32701806-AC
Documentation guide
1
The documentation for the SIMATIC ET 200SP distributed I/O system is arranged into three
areas.
This arrangement enables you to access the specific content you require.
Basic information
The system manual describes in detail the configuration, installation, wiring and
commissioning of the SIMATIC ET 200SP. distributed I/O system. The STEP 7 online help
supports you in the configuration and programming.
Device information
Product manuals contain a compact description of the module-specific information, such as
properties, wiring diagrams, characteristics and technical specifications.
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
11
Documentation guide
1.1 Documentation on CPU 1515SP PC (F)
General information
The function manuals contain detailed descriptions on general topics regarding the SIMATIC
ET 200SP distributed I/O system, e.g. diagnostics, communication, Web server, motion
control and OPC UA.
You can download the documentation free of charge from the Internet
(http://w3.siemens.com/mcms/industrial-automation-systems-simatic/en/manualoverview/tech-doc-et200/Pages/Default.aspx).
Changes and supplements to the manuals are documented in a Product Information.
You can download the product information free of charge from the Internet
(https://support.industry.siemens.com/cs/us/en/view/73021864).
Manual Collection ET 200SP
The Manual Collection contains the complete documentation on the SIMATIC ET 200SP
distributed I/O system gathered together in one file.
You can find the Manual Collection on the Internet
(http://support.automation.siemens.com/WW/view/en/84133942).
"mySupport"
With "mySupport", your personal workspace, you make the most of your Industry Online
Support.
In "mySupport" you can store filters, favorites and tags, request CAx data and put together
your personal library in the Documentation area. Furthermore, your data is automatically
filled into support requests and you always have an overview of your current requests.
You need to register once to use the full functionality of "mySupport".
You can find "mySupport" in the Internet (https://support.industry.siemens.com/My/ww/en).
"mySupport" - Documentation
In the Documentation area of "mySupport", you have the possibility to combine complete
manuals or parts of them to make your own manual.
You can export the manual in PDF format or in an editable format.
You can find "mySupport" - Documentation in the Internet
(http://support.industry.siemens.com/My/ww/en/documentation).
"mySupport" - CAx Data
In the CAx Data area of "mySupport", you can have access the latest product data for your
CAx or CAe system.
You configure your own download package with a few clicks.
CPU 1515SP PC (F)
12
Manual, 05/2017, A5E32701806-AC
Documentation guide
1.1 Documentation on CPU 1515SP PC (F)
In doing so you can select:
● Product images, 2D dimension drawings, 3D models, internal circuit diagrams, EPLAN
macro files
● Manuals, characteristics, operating manuals, certificates
● Product master data
You can find "mySupport" - CAx Data in the Internet
(http://support.industry.siemens.com/my/ww/en/CAxOnline).
Application examples
The application examples support you with various tools and examples for solving your
automation tasks. Solutions are shown in interplay with multiple components in the system separated from the focus in individual products.
You can find the application examples on the Internet
(https://support.industry.siemens.com/sc/ww/en/sc/2054).
TIA Selection Tool
With the TIA Selection Tool, you can select, configure and order devices for Totally
Integrated Automation (TIA).
This tool is the successor of the SIMATIC Selection Tool and combines the known
configurators for automation technology into one tool.
With the TIA Selection Tool, you can generate a complete order list from your product
selection or product configuration.
You can find the TIA Selection Tool on the Internet
(http://w3.siemens.com/mcms/topics/en/simatic/tia-selection-tool).
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
13
Documentation guide
1.1 Documentation on CPU 1515SP PC (F)
SIMATIC Automation Tool
You can use the SIMATIC Automation Tool to run commissioning and maintenance activities
simultaneously on various SIMATIC S7 stations as a bulk operation independently of the TIA
Portal.
The SIMATIC Automation Tool provides a multitude of functions:
● Scanning of a PROFINET/Ethernet network and identification of all connected CPUs
● Address assignment (IP, subnet, gateway) and station name (PROFINET device) to a
CPU
● Transfer of the data and the programming device/PC time converted to UTC time to the
module
● Program download to CPU
● Operating mode switchover RUN/STOP
● Localization of the CPU by means of LED flashing
● Reading out CPU error information
● Reading the CPU diagnostic buffer
● Reset to factory settings
● Updating the firmware of the CPU and connected modules
You can find the SIMATIC Automation Tool on the Internet
(https://support.industry.siemens.com/cs/ww/en/view/98161300).
PRONETA
With SIEMENS PRONETA (PROFINET network analysis), you analyze the plant network
during commissioning. PRONETA features two core functions:
● The topology overview independently scans PROFINET and all connected components.
● The IO check is a fast test of the wiring and the module configuration of a system.
You can find SIEMENS PRONETA on the Internet
(https://support.industry.siemens.com/cs/ww/en/view/67460624).
1.1
Documentation on CPU 1515SP PC (F)
The following additional documentation is required for using the CPU 1515SP PC (F):
● Operating manual S7-1500 software controller
(http://support.automation.siemens.com/WW/view/en/109249299)
● System manual WinCC Advanced V14
(http://support.automation.siemens.com/WW/view/en/109742297)
● System manual ET 200SP distributed I/O system
(http://support.automation.siemens.com/WW/view/en/58649293)
● Manual Server module (http://support.automation.siemens.com/WW/view/en/63257531)
CPU 1515SP PC (F)
14
Manual, 05/2017, A5E32701806-AC
2
Safety notes
WARNING
Life-endangering voltage when control cabinet is open
If the device is installed in a control cabinet, areas or components can be under lifeendangering voltage when the control cabinet is open.
Contact with these areas or components may lead to death through electric shock.
Switch off the power before opening the control cabinet.
If the device is operated in a machine in accordance with the machinery directive, the
provisions of the guideline 2006/42/EC apply.
Safe operation of a plant
WARNING
Risk of fire
The device is classified for use in the area of Industrial Control Equipment as "Open Type"
according to UL508. If overheating occurs, burning material may leak and cause a fire.
For this reason, observe the following information:
• For approval and operation in accordance with UL508, the device must be installed in a
housing complying with UL508.
• Install the device in an enclosure that meets the requirements of sections 4.6 and 4.7.3
of the standards EN 60950-1:2006 and IEC/UL/EN/DIN-EN 60950-1.
If you have questions about the validity of installation in the planned environment, please
contact our service representatives.
NOTICE
Protective measures
To ensure safe operation of a plant, you have to take suitable IT security measures, for
example, network segmentation.
Seal the cover with lead to protect the CFast card with the operating system of the
CPU 1515SP PC (F) against unauthorized access.
For more information on Industrial Security, refer to the Internet
(http://www.siemens.com/industrialsecurity).
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
15
Safety notes
Repairs
WARNING
Damage caused by opening the device
Unauthorized opening of and improper repairs to the device may result in substantial
damage to equipment or endanger the user.
Only authorized personnel are permitted to repair the device.
For additional information on repairs, see section Sending the device to customer service
(Page 99).
ESD guidelines
Modules containing electrostatic sensitive devices (ESDs) can be identified by the following
label:
Strictly follow the guidelines mentioned below when handling modules which are sensitive to
ESD:
● Before working with modules with ESD, you need to ensure that you are free of
electrostatic charge (e.g. by touching a grounded object).
● All devices and tools must be free of static charge.
● Always pull the mains connector and disconnect the battery before installing or removing
modules which are sensitive to ESD.
● Handle modules fitted with ESDs only by their edges.
● Do not touch any connector pins or conductors on modules containing ESDs.
See also
Electromagnetic compatibility (Page 105)
CPU 1515SP PC (F)
16
Manual, 05/2017, A5E32701806-AC
Safety notes
2.1 Notes on use
2.1
Notes on use
WARNING
Hazards at an unprotected machine or plant
According to the results of a risk analysis, hazards can occur at an unprotected machine.
The hazards may lead to personal injury.
According to the risk analysis, the risk of injury to persons can be countered with the
following measures:
• Additional protective equipment at the machine or plant. In this case, the programming,
parameter assignment and wiring of the I/O used, in particular, must be performed in
accordance with the safety criteria (SIL, PL or Cat.) ascertained by means of an
appropriate risk analysis.
• Use of the device for its intended purpose, which can be established by performing a
functional test on the plant. This allows errors in programming, parameter assignment
and wiring to be detected.
• Documentation of the test results which can be entered, if required, into the relevant
safety certificates.
NOTICE
Ambient conditions
Ambient conditions for which the device is not suitable can lead to faults or damage the
device.
Note the following:
• Only operate the device in enclosed areas. If you do not comply with this instruction, the
warranty becomes void.
• Only operate the device in accordance with the ambient conditions given in the technical
specifications.
• Protect the device from dust, moisture and heat.
• Do not expose the device to direct sunlight or other strong sources of light.
• The device must not be used in places with more difficult operating conditions through
corrosive vapors or gases without taking additional protective measures, for example,
supply of clean air.
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
17
3
Product overview
3.1
Fail-safe option
Areas of application
F-CPUs are mainly designed for personal and machine protection. In addition to the safety
program, you can also program standard applications. You can operate the F-CPUs in safety
mode or in standard mode.
Reference
Information on the use of F-CPUs in safety mode is available in the programming and
operating manual SIMATIC Safety - Configuring and Programming
(http://support.automation.siemens.com/WW/view/en/54110126).
You can find information on using the CPU 1505SP (F) software controller in the
corresponding product manual
(https://support.industry.siemens.com/cs/ww/en/view/109740725) and in the F product
information (https://support.industry.siemens.com/cs/ww/en/view/109478599).
CPU 1515SP PC (F)
18
Manual, 05/2017, A5E32701806-AC
Product overview
3.2 Properties
3.2
Properties
Article number
6ES7677-2xAxx-0xx0
The complete article number depends on the system version and the ordering option.
View of the module
The figure below shows the CPU 1515SP PC.
Figure 3-1
CPU 1515SP PC with supplied accessories
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
19
Product overview
3.2 Properties
Properties
CPU 1515SP PC (F) is a PC based automation device in the design of the ET 200SP. It is
used for control and visualization purposes. The supplied IPC DiagBase software provides
basic diagnostics functions and supports you in handling the BIOS.
CPU 1515SP PC (F) has the following technical properties:
● A removable CFast card with the following pre-installations is used as storage medium:
– Windows Embedded Standard 7 operating system
– S7-1500 Software Controller CPU 1505SP (F)
– Optionally with HMI: WinCC Runtime Advanced as of V14 SP1
● Interfaces
– An interface for the exchangeable ET 200SP BusAdapters for connection of
PROFINET IO (2 ports)
– An interface for connecting devices using Industrial Ethernet (Gigabit Ethernet)
– 3 interfaces for USB devices
– One DVI-I interface for a monitor
– A sealable slot for the CFast card
– A slot for an SD/MMC card as additional optional drive
● Supply voltage 1L+ 24 V DC (SELV/PELV). The connection plug is included in the scope
of delivery.
● CPU 1515SP PC (F) is designed for use in industrial environment:
– Compact design
– Fan-less operation
– High robustness
● The CPU 1515SP PC (F) is approved for the degree of protection IP20 and for the
installation in a control cabinet.
CPU 1515SP PC (F)
20
Manual, 05/2017, A5E32701806-AC
Product overview
3.3 Sample configuration
System versions and ordering options
System version
SIMATIC software
CFast card
Article number
WES7 E 32Bit
CPU 1505SP V2.1
30 GB
6ES7677-2AA31-0EB0
WES7 P 64Bit
(multitouch functionality)
CPU 1505SP V2.1
30 GB
6ES7677-2AA41-0FB0
CPU 1505SP V2.1 & WinCC Runtime
Adv. V14 SP1 128PT
30 GB
6ES7677-2AA41-0FK0
CPU 1505SP V2.1 & WinCC Runtime
Adv. V14 SP1 512PT
30 GB
6ES7677-2AA41-0FL0
CPU 1505SP V2.1 & WinCC Runtime
Adv. V14 SP1 2048PT
30 GB
6ES7677-2AA41-0FM0
WES7 E 32Bit
CPU 1505SP F V2.1
30 GB
6ES7677-2FA31-0EB0
WES7 P 64Bit
(multitouch functionality)
CPU 1505SP F V2.1
30 GB
6ES7677-2FA41-0FB0
CPU 1505SP F V2.1 & WinCC
Runtime Adv. V14 SP1 128PT
30 GB
6ES7677-2FA41-0FK0
CPU 1505SP F V2.1 & WinCC
Runtime Adv. V14 SP1 512PT
30 GB
6ES7677-2FA41-0FL0
CPU 1505SP F V2.1 & WinCC
Runtime Adv. V14 SP1 2048PT
30 GB
6ES7677-2FA41-0FM0
CPU 1515SP PC, spare part, without CFast card, without software
3.3
6ES7677-2AA40-0AA0
Sample configuration
Configuration
CPU 1515SP PC (F) is mounted on the mounting rail according to EN 60715. A modular
system is formed with ET 200SP modules in the central rack.
You can use the CPU 1515SP PC (F) as PROFINET IO controller. The PROFINET IO
devices are connected with the SIMATIC BusAdapter BA 2xRJ45 via the ports of the
interface X1 PN (LAN).
Devices can be connected via Industrial Ethernet using the integrated interface
X2 PN/IE (LAN).
The connection to PROFIBUS can be made using the DP master module.
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
21
Product overview
3.3 Sample configuration
Sample configuration
The figure below shows an example configuration with CPU 1515SP PC (F).
Figure 3-2
Example configuration with the CPU 1515SP PC (F)
①
②
③
④
⑤
⑥
⑦
⑧
⑨
⑩
CPU 1515SP PC (F), I/O module, server module
Mounting rail
Flat Panel - Wide Screen Display
USB devices: Keyboard, mouse, printer ...
PROFINET IO device
Camera
Industrial Thin Client ITC
SCALANCE W786
Field programming device
PC/Programming device
CPU 1515SP PC (F)
22
Manual, 05/2017, A5E32701806-AC
Product overview
3.4 Components
3.4
Components
Components of the CPU 1515SP PC (F)
The table below contains an overview of the components of the CPU 1515SP PC (F):
Table 3- 1
Components of the CPU 1515SP PC
Component
Function
Figure
Mounting rail in accordance The mounting rail is the module carriwith EN 60715
er for the CPU 1515SP PC (F).
CPU 1515SP PC (F)
CPU with strain relief and white reference labels
BusAdapter
The BusAdapter allows free selection
of the connection technology for
PROFINET IO. The following versions
are available for CPU 1515SP PC (F):
Server module
•
For standard RJ45 plug
(BA 2×RJ45) ①
•
For direct connection of the bus
cable (BA 2×FC) ②
The server module completes the
configuration of the
CPU 1515SP PC (F) with I/O modules.
The server module is included in the
CPU's scope of delivery.
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
23
Product overview
3.5 Configuration of the devices
3.5
Configuration of the devices
Front view
Figure 3-3
Front view CPU 1515SP PC (F)
① Mounting rail release mechanism
② Labeling strips
③ Server module
④ Cooling fins
⑤ Strain relief
⑥ Reference labels
CPU 1515SP PC (F)
24
Manual, 05/2017, A5E32701806-AC
Product overview
3.6 Operator controls and display elements
3.6
Operator controls and display elements
Front view of the module
The figure below shows the operator control and connection elements of the
CPU 1515SP PC (F).
Figure 3-4
①
②
③
④
⑤
⑥
⑦
View of the CPU 1515SP PC (F)
LED displays for the current operating mode and diagnostic status of the CPU
Power LED
X50:
Slot for the CFast card (flash memory), sealable
Mode selector
X51:
Slot for an optional SD/MMC card
X80:
Connector for 24 V DC supply voltage
X1 PROFINET Slot for BusAdapter for connection of PROFINET IO;
(LAN):
status display for PROFINET
X2 PN/IE (LAN): GbE Ethernet connection with integrated display
⑧
⑨ X60, X61, X62: 3 USB connections
Connection for monitor
⑩ X70 DVI-I:
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
25
Product overview
3.6 Operator controls and display elements
Slot for CFast card
The operating system, Runtime software and project are installed on the supplied SIMATIC
CFast card. The CFast card is the only mass storage device of the CPU 1515SP PC (F).
Note
Unauthorized access
Seal the cover of the shaft with lead to protect the CFast card with the operating system of
the CPU 1515SP PC (F) against unauthorized access and manipulation.
Slot for SD/MMC card
You can use a SIMATIC SD or MMC card as additional storage drive. This drive can be used
to store data via Windows, for example a backup, but not the operating system, the Runtime
software or the project.
Permitted SD cards: SDHC up to 32 GB, SDXC up to 2 TB.
USB connections
Two USB high-current (500 mA) interfaces and one low-current (100 mA) interface can be
used at the same time.
MAC addresses
The MAC address consists of a 3-byte manufacturer ID and a 3-byte device ID (consecutive
number).
Each device is already assigned four MAC addresses in the factory. The front of the CPU
1515SP PC (F) is lasered with the MAC addresses 1 and 4. With the MAC addresses 2 and
3, the consecutive numbers are incremented. If, for example, the first MAC address is
08-00-06-6B-80-C0, the second MAC address is 08-00-06-6B-80-C1.
Table 3- 2
Assignment of the MAC addresses
Assignment
MAC address 1
MAC address 2
X2 PN/IE (LAN)
•
Visible in STEP 7 for accessible devices
•
Lasered on the front of the CPU (start of the number range)
X1 PROFINET (LAN)
•
Visible in STEP 7 for accessible devices
MAC address 3
Port X1 P1 (required for LLDP, for example)
MAC address 4
Port X1 P2 R (required for LLDP, for example)
•
Lasered on the front of the CPU (end of the number range)
CPU 1515SP PC (F)
26
Manual, 05/2017, A5E32701806-AC
Product overview
3.6 Operator controls and display elements
Connector for supply voltage
CPU 1515SP PC (F) has a 2-pole terminal for the power supply.
The connection plug for the supply voltage is plugged in when the CPU is shipped from the
factory.
Mode selector
Use the mode selector to set the CPU operating mode.
Table 3- 3
Mode selector positions
Position
Meaning
Description
RUN1
RUN
Operating mode
STOP
Operating mode STOP1
The CPU is not processing the user program.
The outputs are set to a "safe" state.
The CPU is processing the user program.
MRES
Memory reset
For active S7-1500 software controller2 only:
CPU memory reset
1
RUN and STOP indicate the selected operating state. The LED displays RUN and STOP display the actual operating
state of the CPU 1515SP PC (F).
2
See the S7-1500 software controller manual
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
27
Product overview
3.7 Scope of delivery
3.7
Scope of delivery
3.7.1
Unpacking the device
When unpacking
When unpacking, make sure to check the following:
● Check packaging and contents for visible damage from transport.
● Check the delivery for completeness.
Please inform your Siemens contact partner should you determine damages from
transport or any irregularities.
● Keep the supplied documentation and licenses. They belong to the device and are the
proof that you have purchased the software preinstalled on the CFast card.
Documentation and licenses are required for initial commissioning and for any questions
that arise.
● Keep the original packaging in case the device needs to be transported again.
NOTICE
Damage to the device during transport and storage
If a device is transported or stored without packaging, it is unprotected from shocks,
vibrations, pressure and moisture. Damaged packaging indicates that environmental
conditions have already had a significant impact on the device.
The device might be damaged.
Do not dispose of the original packaging. Pack the device for transport and storage.
NOTICE
Damage to the device caused by condensation
If the device was exposed to low temperatures or extreme variations in temperature during
transport, this may cause moisture to build up on or in the device (condensation).
Moisture can cause short-circuits in the electrical circuits and damage the device.
Proceed as follows to avoid damage:
• Store the device in dry conditions.
• Make sure it adapts to room temperature before commissioning.
• Do not expose the device to direct heat radiation from a heater.
• If condensation has developed, wait for approximately 12 hours or until the device is
completely dry before you switch it on.
CPU 1515SP PC (F)
28
Manual, 05/2017, A5E32701806-AC
Product overview
3.7 Scope of delivery
WARNING
Electric shock and fire hazard from damaged device
A damaged device can carry dangerous voltage and trigger a fire in the machine or plant. A
damaged device has unpredictable properties and states.
Death or severe injury could occur.
Make sure that the damaged device is not installed and commissioned accidentally. Label
the damaged device correspondingly and keep it locked up. Have the device repaired
without delay.
Identification data
The identification data can be used to clearly identify the device when a repair is necessary.
Make a note of the following data for your devices:
● The article number of the CPU 1515SP PC (F) is located on the order form.
● Depending on the scope of delivery, the "Certificate-of-License" is included in the license
verification for the S7-1500 software controller and for WinCC Runtime Advanced V14
SP1.
● The "Microsoft Windows Product Key" can be found on the "Certificate of Authenticity"
label.
● The first and the last MAC addresses are located on the device.
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
29
Product overview
3.7 Scope of delivery
3.7.2
Scope of delivery - System version WES7 E 32Bit 4GB RAM
Note
The designation CPU 1515SP PC with the article number 6ES7677-2AA40-0AA0 is always
on the device regardless of the order option.
The following components are included in the scope of delivery of the CPU 1515SP PC:
Order option
CPU 1515SP PC
Article number 6ES7677-2AA31-0EB0
CPU 1515SP PC
(spare part)
6ES7677-2AA40-0AA0
CPU
X
X
Strain relief with fixing screws
X
X
Server module
X
X
30 GB CFast card with the following
pre-installations:
•
Windows Embedded Standard 7 E
operating system
X
–
•
S7-1500 Software Controller
CPU 1505SP
X
–
•
WinCC RT Advanced as of V14
SP1
–
–
Restore DVD for image restore
X
–
"Documentation and Drivers" DVD
X
–
Windows-Certificate of Authenticity
(CoA)
X
–
Certificate of License (COL)
X
–
USB stick with SIMATIC license keys
X
–
Product information
X
–
CPU 1515SP PC (F)
30
Manual, 05/2017, A5E32701806-AC
Product overview
3.7 Scope of delivery
The following components are contained in the scope of delivery of the CPU 1515SP PC F:
Order option
CPU 1515SP PC F
Article number 6ES7677-2FA31-0EB0
CPU
X
Strain relief with fixing screws
X
Server module
X
30 GB CFast card with the following pre-installations:
•
Windows Embedded Standard 7 E operating system
X
•
S7-1500 Software Controller CPU 1505SP F
X
•
WinCC RT Advanced as of V14 SP1
–
Restore DVD for image restore
X
"Documentation and Drivers" DVD
X
Windows-Certificate of Authenticity (CoA)
X
Certificate of License (COL)
X
USB stick with SIMATIC license keys
X
Product information
X
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
31
Product overview
3.7 Scope of delivery
3.7.3
Scope of delivery - System version WES7 P 64Bit 4GB RAM
Note
The designation CPU 1515SP PC with the article number 6ES7677-2AA40-0AA0 is always
on the device regardless of the order option.
The following components are included in the scope of delivery of the CPU 1515SP PC:
Order option
CPU 1515SP PC
Article number 6ES7677-2AA41-0FB0
CPU 1515SP PC + HMI
CPU 1515SP PC
(spare part)
6ES7677-2AA41-0FK0 HMI
128PT
6ES7677-2AA40-0AA0
6ES7677-2AA41-0FL0 HMI
512PT
6ES7677-2AA41-0FM0 HMI
2048PT
CPU
X
X
X
Strain relief with fixing
screws
X
X
X
Server module
X
X
X
•
X
Windows Embedded Standar
d 7 P operating system
X
–
•
S7-1500 Software Controller CPU 1505SP
X
X
–
•
WinCC RT Advanced as
of V14 SP1
–
X
–
X
X
–
"Documentation and Drivers" X
DVD
X
–
Windows Certificate of Authenticity (CoA)
X
X
–
Certificate of License (CoL)
X
X
–
USB stick with SIMATIC
license keys
X
X
–
Product information
X
X
–
30 GB CFast card with the
following pre-installations:
Restore DVD for image restore
CPU 1515SP PC (F)
32
Manual, 05/2017, A5E32701806-AC
Product overview
3.7 Scope of delivery
The following components are contained in the scope of delivery of the CPU 1515SP PC F:
Order option
CPU 1515SP PC F
Article number 6ES7677-2FA41-0FB0
CPU 1515SP PC F + HMI
6ES7677-2FA41•
0FK0 HMI 128PT
•
0FL0 HMI 512PT
•
0FM0 HMI 2048PT
CPU
X
X
Strain relief with fixing screws
X
X
Server module
X
X
30 GB CFast card with the following
pre-installations:
•
Windows Embedded Standard 7 P
operating system
X
X
•
S7-1500 Software Controller CPU
1505SP F
X
X
•
WinCC RT Advanced as of V14
SP1
–
X
Restore DVD for image restore
X
X
"Documentation and Drivers" DVD
X
X
Windows Certificate of Authenticity
(CoA)
X
X
Certificate of License (CoL)
X
X
USB stick with SIMATIC license keys
X
X
Product Information
X
X
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
33
4
Installing
4.1
Basics
Introduction
The CPU 1515SP PC (F) is an open operation resource. This means that you may only
install it in enclosures, cabinets or electrical operating areas. These housings, cabinets or
electrical operating areas must only be accessible with a key or tool. Access may only be
possible for instructed or authorized personnel.
Installation location
CPU 1515SP PC (F) must be installed in a suitable enclosure or suitable control cabinet with
at least IP54 degree of protection according to EN 60529 and the ambient conditions for the
operation of the equipment must be taken into consideration.
Installation position
You can install the ET 200SP distributed I/O system in any position. The preferred mounting
position is horizontal mounting on a vertical wall.
The restrictions regarding ambient temperature and maximum configuration apply to the
CPU 1515SP PC (F) depending on the mounting position.
NOTICE
Damage to the modules
Modules can be damaged if exposed to ambient temperatures higher than permitted.
The following ambient temperatures must not be exceeded during operation:
• Horizontal mounting
– 60 °C for an installation with up to 32 I/O modules.
– 55 °C for an installation with up to 64 I/O modules.
• Vertical mounting
– 50 °C for an installation with up to 32 I/O modules.
For more detailed information, refer to section Mechanical and climatic ambient conditions
(Page 108)
CPU 1515SP PC (F)
34
Manual, 05/2017, A5E32701806-AC
Installing
4.1 Basics
Mounting rail
CPU 1515SP PC (F) is mounted on a mounting rail according to EN 60715 (35 × 7.5 mm
and/or 35 × 15 mm).
You must ground the mounting rail separately in the control cabinet. Exception: If you install
the rail on grounded, zinc-plated mounting plates, there is no need to ground the rail
separately.
Note
If the ET 200SP distributed I/O system is exposed to vibration and shock loads, both ends of
the ET 200SP system assembly must be mechanically fixed to the mounting rail (e.g using
8WA1010-1PH01 ground terminals). This measure prevents the ET 200SP from shifting to
the side.
Note
If the ET 200SP distributed I/O system is exposed to high vibration and shock load, we
recommend that you screw the mounting rail to the mounting surface at intervals of approx.
200 mm.
Suitable surface finishes are:
● Steel strip in accordance with Appendix A of EN 60715 or
● Tinned steel strip. We recommend the use of the mounting rails in section
Accessories/spare parts (Page 133).
Note
Mounting rails of other manufacturers
If you use mounting rails from other manufacturers, ensure that they have the properties
required for your climatic and mechanical ambient conditions.
Check whether the mounting rails meet the requirements for a protective conductor.
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
35
Installing
4.1 Basics
Minimum clearances
Maintain the following minimum clearances when installing or dismantling the
CPU 1515SP PC (F).
Figure 4-1
Minimum clearances
Installation rules
● After the CPU 1515SP PC (F) there is a BaseUnit BU..D with incoming supply voltage L+
(light terminal box).
● This is followed by BaseUnits BU..B (with dark-colored terminal box).
● The respective corresponding I/O modules can be connected to the BaseUnits.
Suitable combinations of BaseUnits and I/O modules can be found in the ET 200SP
System Manual (http://support.automation.siemens.com/WW/view/en/84133942).
● The server module completes the installation.
Note
Only install the CPU 1515SP PC (F) when the power supply is switched off.
CPU 1515SP PC (F)
36
Manual, 05/2017, A5E32701806-AC
Installing
4.2 Hardware configuration
4.2
Hardware configuration
Maximum mechanical configuration
As soon as one of the following rules applies, the maximum configuration has been reached:
Table 4- 1
Maximum mechanical configuration
Properties
Rule
Number of modules
•
•
Horizontal mounting
–
0 to 60 °C ambient temperature:
a maximum of 32 I/O modules and USB load
–
0 to 55 °C ambient temperature:
a maximum of 64 I/O modules and USB load
Vertical mounting
–
Backplane bus length
0 to 50 °C ambient temperature:
a maximum of 32 I/O modules and USB load
Maximum 1 m mounting width (without CPU 1515SP PC (F), including
server module)
Electrical maximum configuration
The number of operable I/O modules of a potential group is limited by the
● Power consumption of the I/O modules
● Power consumption of the components supplied via these I/O modules
The maximum current-carrying capability of the terminals on the BaseUnit L+/ground is 10 A.
USB load
In case of maximum configuration with the CPU 1515SP PC (F), the USB load must also be
taken into consideration:
● Horizontal mounting
– Ambient temperature of 0 to 60 °C with maximum 32 I/O modules and 3 x 100 mA
USB load
– Ambient temperature of 0 to 55 °C with maximum 64 I/O modules and 2 x 500 mA +
1 x 100 mA USB load
● Vertical mounting
– Ambient temperature of 0 to 50 °C with maximum 32 I/O modules and 3 x 100 mA
USB load
Address space
The address space is predefined. However, you can adjust the address space in the user
program.
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
37
Installing
4.3 Installing CPU 1515SP PC (F)
4.3
Installing CPU 1515SP PC (F)
Requirements
The mounting rail is fitted.
Required tools
3 to 3.5 mm screwdriver (only to fix the strain relief and dismantle the BusAdapter)
Fixing strain relief
Fasten the strain relief at the upper and lower left side of the CPU 1515SP PC (F) with the
supplied screws.
Installing CPU 1515SP PC (F)
1. Install the CPU on the mounting rail.
2. Swivel the CPU back until you hear the mounting rail release click into place
3. To check that the CPU has correctly clicked into place, pull on the underside of the
enclosure.
Figure 4-2
Installing CPU 1515SP PC (F)
CPU 1515SP PC (F)
38
Manual, 05/2017, A5E32701806-AC
Installing
4.3 Installing CPU 1515SP PC (F)
Disassemble CPU 1515SP PC (F)
The BaseUnits with the I/O modules are located to the left of the CPU 1515SP PC (F):
1. Switch off the supply voltage on the CPU.
2. Press the mounting rail release button on the first BaseUnit and, at the same time, move
the CPU in parallel to the left until it comes off the remaining the module group.
Note: The mounting rail release button is located above the CPU.
3. While pressing the mounting rail release button on the CPU, swivel the CPU out of the
mounting rail.
Note
It is not necessary to remove the BusAdapter from the CPU 1515SP PC (F).
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
39
5
Connection
5.1
Notes on connection
Note
Rules and regulations for operation
Observe the information contained in the Wiring section in the system manual ET 200SP
distributed I/O system (http://support.automation.siemens.com/WW/view/en/58649293) and
in the function manual Designing interference-free controllers
(http://support.automation.siemens.com/WW/view/en/59193566).
NOTICE
Fault caused by I/O devices
The connection of I/O devices can lead to faults on the device.
Injury to persons and damage to the machine or plant could result.
Note the following when connecting I/O devices:
• Read the documentation related to the I/O devices. Follow all instructions given in the
documentation.
• Only connect I/O devices which are suitable for use in industrial environments according
to EN 61000-6-2/EC 61000-6-2.
• You may only connect hot-plug capable I/O devices when the power supply is switched
off.
Note
Feedback through USB devices
If USB devices are connected which - contrary to the USB 2.0 specification - feed voltage
back to the host interface, the startup of the CPU 1515SP PC (F) is not ensured upon powerup.
Regenerative feedback is generally not permitted.
CPU 1515SP PC (F)
40
Manual, 05/2017, A5E32701806-AC
Connection
5.2 Terminal and block diagram
5.2
Terminal and block diagram
Block diagram
The figure below shows the block diagram of the CPU 1515SP PC (F).
①
②
③
④
⑤
Switch
X1 PN (LAN)
PROFINET interface X1
Electronics
P1
PROFINET interface X1 Port 1
Backplane bus interface
P2
PROFINET interface X1 Port 2
Internal supply voltage
L+
24 V DC supply voltage
Mode selector
M
Ground
X50
CFast card
LK1, LK2
LED Link TX/RX
X51
SD/MMC card
LK3
LED Link
X60
USB interface 2.0, 0.5 A
R/S
RUN/STOP LED (yellow/green)
X61, X62
USB interface 2.0, 0.5 A
ER
ERROR LED (red)
X70
DVI-I interface
MT
MAINT LED (yellow)
X80 24 V DC
Infeed of supply voltage
PWR
POWER LED (yellow/green)
X2 PN/IE (LAN)
Ethernet interface X2
Figure 5-1
Block diagram for CPU 1515SP PC (F)
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
41
Connection
5.3 Electrical configuration
5.3
Electrical configuration
Non-isolated configuration
Note
Unlike the distribution I/O system ET 200SP, only a non-isolated configuration is possible the
CPU 1515SP PC (F).
CPU 1515SP PC (F)
42
Manual, 05/2017, A5E32701806-AC
Connection
5.3 Electrical configuration
The figure below shows a CPU 1515SP PC (F) in the overall configuration with infeed from a
TN-S system. The power supply supplies the CPU 1515SP PC (F) and the load circuits for
the 24 V DC modules.
With the CPU 1515SP PC (F) there is a fixed connection between the ground infeed terminal
and the contact springs to the mounting rail. You must ground the mounting rail separately in
the control cabinet.
①
②
③
④
Master switch
Short-circuit and overload protection
Load current supply (galvanic isolation)
In the CPU 1515SP PC (F), this connection is automatically established.
The represented layout of the power connections does not correspond to the actual layout; it
was chosen for demonstration purposes only.
Figure 5-2
Connecting the load voltage reference potential
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
43
Connection
5.4 Connecting devices to networks
5.4
Connecting devices to networks
The following options are available for integrating devices into existing or planned system
environments and networks.
Ethernet
You can use the integrated Ethernet interface X2 PN/IE (LAN) (10/100/1000 Mbps) for
communication and data exchange with automation devices, for example, SIMATIC S7.
Only ASCII characters are permitted in the name of the interface X2 PN/IE (LAN) in the
TIA Portal, e.g. PROFINET_2.
You need suitable software to do this: STEP 7, WinCC, SIMATIC NET.
Note
Use a Category 5e Ethernet cable (Cat-5e cable) for operation with 1000 Mbps.
PROFINET
PROFINET operation is possible via the X1 PN (LAN) interface and the approved
BusAdapter.
PROFIBUS
The connection to PROFIBUS can be made using the DP master module.
5.5
Securing cables
The strain relief for connection lines prevents the USB and the PROFINET connector coming
loose from the CPU 1515SP PC (F). The strain relief is included in the scope of delivery.
WARNING
Flying sparks due to loose cables
Risk of explosion in hazardous areas.
USB cables and PROFINET connectors may detach from the device in the case of strong
oscillation and high vibrating loads.
Attach these cables to the strain relief of the device using cable ties.
CPU 1515SP PC (F)
44
Manual, 05/2017, A5E32701806-AC
Connection
5.5 Securing cables
Requirements
● The strain relief is fixed to the CPU.
● The CPU is installed.
Procedure
Secure the USB and PROFINET cables to the strain relief using cable ties.
Figure 5-3
Secured cables
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
45
6
Diagnostics, error and system alarm
6.1
Status and error display
LED display
The figure below shows the LED displays of the CPU 1515SP PC (F).
①
②
③
④
RUN/STOP LED (yellow/green LED)
ERROR LED (red LED)
MAINT LED (yellow LED)
POWER LED (yellow/green LED)
Figure 6-1
LED displays of the CPU 1515SP PC (F).
CPU 1515SP PC (F)
46
Manual, 05/2017, A5E32701806-AC
Diagnostics, error and system alarm
6.1 Status and error display
Meaning of the LED displays with active software controller
CPU 1515SP PC (F) has a display of the current operating state and of the diagnostics
status (three LEDs).
The following table shows the meaning of the color combinations of the LED displays in
connection with the software controller.
Table 6- 1
Meaning of the LED displays
RUN/STOP LED
ERROR LED
MAINT LED
Meaning
POWER OFF
LED off
LED off
LED off
Starting of the CPU 1515SP PC (F) in
the "Windows only" mode
No power supply.
The software controller of the
CPU 1515SP PC (F) has not been downloaded or the
software controller of the
CPU 1515SP PC (F) is in the operating
state Power OFF.
An error has occurred.
LED off
LED green
LED flashes red
LED off
LED off
LED off
Software controller of the
CPU 1515SP PC (F) is in RUN mode.
A diagnostics event is pending.
LED green
LED flashes red
LED off
LED green
LED off
LED lights up
yellow
LED green
LED off
Maintenance demanded for the plant.
The affected hardware must be exchanged within a short period.
Maintenance required for the plant.
LED lights up
yellow
LED off
LED flashes yellow
You must exchange the affected hardware within a foreseeable period.
LED off
Software controller of the CPU is in the
operating state STOP.
Firmware update successfully completed
The user program is causing an error.
LED lights up
yellow
LED flashes red
LED flashes yellow
LED flashes yellow
LED off
LED off
CPU defective
CPU is performing internal activities
during STOP, e.g. ramp-up after STOP.
Loading the user program
Startup (transition from RUN → STOP)
LED flashes
yellow/green
LED off
LED off
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
47
Diagnostics, error and system alarm
6.1 Status and error display
RUN/STOP LED
ERROR LED
MAINT LED
Meaning
Startup (CPU booting)
LED flashes
yellow/green
LED flashes red
LED flashes yellow
Test of LEDs during startup, inserting a
module.
LED flashing test
POWER LED
Table 6- 2
POWER LED
POWER LED
Meaning
No supply voltage or supply voltage too low
LED off
Supply voltage present;
LED lights up yellow
running through BIOS phase;
operating system is shut down
Supply voltage present;
LED green
Booting or operation of the operating system
CPU 1515SP PC (F)
48
Manual, 05/2017, A5E32701806-AC
Commissioning
7.1
7
Notes on commissioning
WARNING
Improper commissioning in hazardous areas
Device failure or risk of explosion in hazardous areas.
• Do not commission the device unless it is fully mounted and connected according to the
specifications in the section Enhanced Write Filter (EWF) (Page 78).
• Before commissioning, please consider the effects on other devices in the plant.
CAUTION
Hot surfaces
Risk of burns due to hot surfaces.
During operation, only touch the device with appropriate protective gloves.
NOTICE
Condensation in the device
Damage to the device due to condensation if the temperature between transport or storage
and the installation site differs by more than 20 °C (36 °F).
Before commissioning the device, leave it to stand for several hours in the new
environment.
NOTICE
Data loss
Data loss may occur if write filters are used incorrectly.
Therefore, note the information on write filters.
Two write filters are available for configuration under Windows Embedded:
• Enhanced Write Filter (Page 78)
• File Based Write Filter (Page 82)
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
49
Commissioning
7.2 Initial commissioning
7.2
Initial commissioning
Requirements
The following conditions must be met before you commission the open controller for the first
time.
● CPU 1515SP PC (F) is mounted.
● The CFast card is inserted.
● No data carriers are connected via USB.
● The following hardware is available: A monitor, a USB keyboard, a USB mouse
Procedure
1. Connect a monitor via a DVI-I cable.
2. Connect a keyboard and a mouse to the CPU via USB.
3. Connect the power supply.
→ The PWR LED lights up yellow first, then green.
→ The device carries out the hardware initialization.
4. Wait until the Siemens logo disappears from the screen.
5. Follow the instructions on the screen to configure the device
NOTICE
Faulty installation
If you change the default values in the BIOS Setup or switch off the device during the
installation, the installation will be disrupted and the operating system will not be installed
correctly. The operational reliability of the device and the plant is endangered.
Do not switch of the device during the entire installation process. Do not change the default
values in the BIOS Setup.
Result
● The WES7 operating system is installed.
● WES7 P: The Multitouch functions are available.
● The operating system's start screen is displayed after each startup.
● A login window appears if a password was entered during the initial commissioning.
CPU 1515SP PC (F)
50
Manual, 05/2017, A5E32701806-AC
Commissioning
7.2 Initial commissioning
Initial commissioning an open controller
The basic settings, user name, administrator password and IP address are prompted for
during initial power-up of your CPU 1515SP PC (F). The device is then automatically set up
for the operating system that is installed on the CFast card. Restart the device after the
operating system has been set up.
Note
The initial commissioning is not possible with a Multitouch panel, as the Multitouch driver is
only available after the installation of the operating system.
User name, computer name, password
When you enter a "User name", this is suffixed with "-PC" under "Computer name". The
computer name must not exceed 15 characters.
Note
This user has administrator rights!
For security reasons, enter a password for this user (administrator).
IP address
The IP address (192.168.1.1) and the subnet mask (255.255.255.0) for the X2 interface are
pre-set in the logon dialog.
You use the buttons to make your changes or to retain the pre-set values.
Note
The initial TIA Portal download must be performed using set IP address via the GB Ethernet
interface X2 in order that the PROFINET interface X1 and the hardware configuration are
correctly assigned.
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
51
Commissioning
7.2 Initial commissioning
User "Operator"
A user "Operator" with standard user rights is already created on the Windows system.
The user is in a user group "SIEMENS TIA Engineer". This grants the user the rights to use
the installed SIMATIC software products.
To be able to use the CPU 1515SP PC (F) directly, the Windows "Autologon" is activated for
the user "Operator". No password is preset.
Note
When you assign a password, change the entry for the Windows "Autologon" function
accordingly in order that the function remains activated.
Administrator rights
You need administrator rights for the following actions:
● Back up the data in the root directory of the C partition.
● Installing the language pack
Screen resolution
In Windows Embedded Standard 7, the values that are determined for the monitor via the
DVI-I interface are set for the screen resolution.
CPU 1515SP PC (F)
52
Manual, 05/2017, A5E32701806-AC
Commissioning
7.3 Initial configuration of an Open Controller
7.3
Initial configuration of an Open Controller
Creating the configuration
You have created a new project in the TIA Portal.
To create the configuration in the TIA Portal, follow these steps:
1. Double-click "Add new device" in the project tree.
2. In "PC-Systeme > SIMATIC S7 Open Controller > ET 200SP Open Controller >", select
the "CPU 1515SP PC (F) (+HMI)".
3. Select the appropriate version.
The configured Open Controller is displayed in the device view.
4. The following components can be seen in the Open Controller:
– Onboard interface X2 (GB Ethernet Windows interface) that is assigned directly to the
PC station (1 port)
– Replaceable BusAdapter X1, which is directly assigned to the software controller (2
ports)
– On the right side (behind the plugged modules in the rack): the configured software
controller CPU 1505SP (F) and WinCC Runtime Advanced.
5. Insert the server module.
The server module at the right end of the configuration forms the termination of the CPU
with the I/O modules.
Setting the IP addresses:
In the Inspector window under "Properties":
● Onboard interface X2: the configured, specified IP address is identical with the Windows
IP address that is set during the first commissioning on the open controller.
● BusAdapter X1: the configured, specified IP address is identical with the IP address that
is set during the first commissioning in the panel of the software controller (display
application).
Important properties of the Software Controller
Change the properties in the Inspector window under "Properties" if required:
● Selecting startup type
● System diagnostics
● Setting the storage location for retentive data
● Setting up copy protection
● Using the LEDs of the hardware
● Configuring the Web server
● Assigning interfaces for the communication
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
53
Commissioning
7.3 Initial configuration of an Open Controller
Establish HMI connection
1. Right-click the WinCC RT Advanced in the device view.
2. Start the HMI device wizard.
3. Apply all default settings.
The wizard creates system images for you with the corresponding navigation.
4. Switch to the connection view in the network view.
5. Click on WinCC RT Advanced.
6. Drag (with mouse button pressed) from the WinCC RT Advanced software to the S7-1500
software controller (for example, CPU 1505SP).
A network connection is established between the two devices.
Downloading the project to the target system
The complete PC station is downloaded the first time you download the configuration.
1. Select the complete PC system in the device view.
2. Click the "Download to device" button.
3. Make the following settings:
– Type of connection
– Specify the interface of the programming device
– Specify the X2 interface on the Open Controller
Note
The first TIA Portal download must be via the "X2" interface.
Only ASCII characters are permitted in the name of the interface X2 PN/IE (LAN) in the
TIA Portal, e.g. PROFINET_2.
Download and compile the project. The hardware configuration and the first download are
now completed.
WinCC RT Advanced
WinCC Runtime Advanced contains all the essential functions for operator control and
monitoring of machinery or plants.
Reference
For more information on WinCC RT Advanced, refer to the WinCC Advanced V14
(http://support.automation.siemens.com/WW/view/en/109742297) system manual.
CPU 1515SP PC (F)
54
Manual, 05/2017, A5E32701806-AC
Commissioning
7.4 Installing license keys
7.4
Installing license keys
Licensing the software
A license key is not required to operate the S7-1500 software controller CPU 1505SP (F)
V2.x. The software controller is permanently coupled to your CPU 1515SP PC (F). It is not
necessary to input the key via the Automation License Manager!
WinCC RT Advanced requires a product-specific license key. This is located on the supplied
USB stick.
Prior to commissioning, you must install the license key for the HMI powertags using the
Automation License Manager (ALM).
Perform the licensing directly via the CPU 1515SP PC (F).
Requirements
● Initial commissioning was successfully completed.
● Windows Embedded Standard 7 has started.
● The enhanced write filter EWF must be disabled on the CPU 1515SP PC (F).
Installing License keys with local configuration
The Automation License Manager is preinstalled on the CPU 1515SP PC (F).
Open the software using the icon on the desktop or a menu command.
1. In the Windows start bar, select Start > All Programms > Siemens Automation >
Automation License Manager.
2. Follow the instructions of the Automation License Manager.
Using a programming device/PC to install the license keys
The Automation License Manager is pre-installed on a programming device / PC with
STEP 7 and the CPU 1515SP PC (F).
1. Connect the CPU 1515SP PC (F) to a programming device / PC.
2. Connect the supplied USB stick to the programming device/PC.
3. Select the menu command Start >SIMATIC >License Management > Automation
License Manager.
4. Select the menu command Bearbeiten > Rechner verbinden and enter the IP address of
the CPU 1515SP PC (F) (default 192.168.1.1).
5. Drag the license keys from the USB stick to the system partition C: of the
CPU 1515SP PC (F).
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
55
Commissioning
7.4 Installing license keys
Saving and securing license keys in the case of restore and repair
Note
Loss of license keys
A SIMATIC license key cannot be copied or duplicated. If you drag the license keys from
your USB-Stick to your CPU 1515SP PC (F), no copies are then left on the USB stick.
Secure your purchased license keys before restoring the delivery state (Restore) or in the
case of repair. To do this, move the license keys to a USB stick and keep this stick in a safe
place.
If a fault occurs with your license keys on the CPU 1515SP PC (F), contact your local
Siemens representative. Make sure to have the "Certificate of License" (CoL) to hand.
Note
The EWF (Page 78) write filter serves to protect your license keys and your configuration.
Reference
For additional information on licenses, refer to the Automation License Manager manual.
You can find the manual for the CPU 1515SP PC (F) under Start > All Programs > Siemens
Automation > Documentation and in the Internet
(http://support.automation.siemens.com/WW/view/en/56956174).
CPU 1515SP PC (F)
56
Manual, 05/2017, A5E32701806-AC
Commissioning
7.5 Windows Security Center
7.5
Windows Security Center
Warning from the Windows Security Center
A warning from the Windows Security Center appears when you first switch on your device.
The Security Center check the status of the device with regard to the main security aspects
listed below. If the Security Center finds a problem during this check, it gives
recommendations on how to better protect the device.
● Firewall: The Windows firewall contributes to protecting the device by preventing the
access of unauthorized users via a network or the Internet. Windows checks whether the
device is protected by a software firewall.
As delivered, the firewall is enabled.
● Antivirus software: Antivirus programs contribute to protecting the device against viruses
and other security threats. Windows checks whether a comprehensive up-to-date
program is used on the device.
No antivirus software is installed as delivered.
● Automatic updates: With the help of automatic updates, Windows can routinely check for
the latest major updates for the device and install these automatically. In the delivery
state, this option is disabled.
Note
To keep Windows up-to-date, enable either the automatic update function of Windows or
install updates manually. Before the installation, check the size of the package to be
installed and decide if you need the update and if there is sufficient storage space
available.
Some updates may make it necessary to use a larger CFast card or to change the
partitioning. You can find information on changing the partition size in the Change
partitioning (Page 85) chapter.
Configure the Security Center to suit your requirements.
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
57
Commissioning
7.6 Switching CPU 1515SP PC (F) on/off
7.6
Switching CPU 1515SP PC (F) on/off
Requirements
Initial commissioning was successfully completed.
Switching on the CPU 1515SP PC
1. Switch on the power supply of the CPU.
The Boot Manager GRUB4DOS opens.
2. Select the mode in which the CPU 1515SP PC (F) should start:
– Only with the Windows operating system.
– With the Windows operating system and the S7-1500 software controller (default).
Figure 7-1
Boot Manager GRUB4DOS
Switch off CPU 1515SP PC (F)
1. To switch off the Windows function, use StartShut down.
The PWR LED changes from green to yellow.
The Windows function shuts down the Windows operating system and the S7-1500
software controller.
If the device will not be used for a longer period after the shutdown, de-energize the device.
CPU 1515SP PC (F)
58
Manual, 05/2017, A5E32701806-AC
8
Functions
8.1
Monitoring functions
Introduction
CPU 1515SP PC (F) has monitoring functions that you can use with the corresponding
software. The following display, monitoring and control functions are available.
● Temperature monitoring
● Monitoring of drives with SMART functionality
● Operating hours counter (information on the total runtime)
SIMATIC IPC DiagBase
The SIMATIC IPC DiagBase software is contained in the scope of delivery of the
CPU 1515SP PC (F).
With the SIMATIC IPC DiagBase software, you use the functions for local monitoring. Use
the DiagBase Management Explorer application to obtain a clearer overview for monitoring.
The DiagBase Alarm Manager notifies you of individual alarms.
Note
For additional information, refer to the online help for the SIMATIC IPC DiagBase software.
SIMATIC IPC DiagMonitor
The SIMATIC IPC DiagMonitor software is provided on a CD.
Potential system failures are detected and reported in good time with the diagnostics and
alerting software. The software is also used for remote diagnostics.
The software contains:
● The software for the stations to be monitored
● A library for creating your own applications
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
59
Functions
8.2 Retentive memory NVRAM
Temperature monitoring
Three thermistors monitor the temperature at multiple locations of the CPU 1515SP PC (F):
● Processor temperature
● Temperature in the vicinity of the RAM ICs/blocks
● Temperature of the basic module
If one of the temperature values exceeds the set temperature threshold, the temperature
monitoring triggers a temperature error. The temperature error activates the IPC DiagBase
and/or IPC DiagMonitor software.
The temperature error remains stored until the temperatures fall below the temperature
threshold again and it is reset using one of the following measures:
● Acknowledgment of the error message by the monitoring software
● Restart of the device
8.2
Retentive memory NVRAM
Retentive memory is non-volatile memory for saving a limited quantity of data in the event of
power failure.
The data defined as retentive is stored in retentive memory. This data is retained beyond a
power-off or power failure.
A corresponding function is implemented in the S7-1500 software controller to allow NVRAM
to be used there. Up to 410 KB of data is backed up to non-volatile data memeory by this in
the event of power failure. This function can be set on the engineering station in the TIA
Portal.
CPU 1515SP PC (F)
60
Manual, 05/2017, A5E32701806-AC
Functions
8.3 BIOS description
8.3
BIOS description
8.3.1
Introduction
BIOS setup
The BIOS setup is located in the BIOS ROM. The information is stored to the memory of the
CPU 1515SP PC (F) via the system configuration.
You can set the following using the Setup:
● The hardware configuration, for example, drive type
● The system properties
● time and date
Note
The American keyboard layout applies in the BIOS.
Changing the device configuration
The device configuration is preset for working with the supplied software.
Only change the set values if you have made technical changes to your device.
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
61
Functions
8.3 BIOS description
8.3.2
Starting BIOS setup
Start the setup program as follows:
1. Disconnect the device from the power supply and switch it on again (cold restart).
The following screen appears in the default setting of the CPU 1515SP PC (F) after it is
switched on:
Figure 8-1
BIOS setup
After completion of the startup test, you have the option of starting the SETUP program.
The following BIOS message appears:
Press F2 go to Setup Utility
Press F12 go to Boot Manager
2. Press the <F2> button while the message is on the screen.
CPU 1515SP PC (F)
62
Manual, 05/2017, A5E32701806-AC
Functions
8.3 BIOS description
8.3.3
BIOS setup menus
Overview of BIOS setup
The menus and submenus are shown on the following pages.
①
②
③
④
Menu bar
Selectable submenu
Help window
Operating line
Figure 8-2
Structure of the BIOS setup menus
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
63
Functions
8.3 BIOS description
Menu structure
In the menu bar ①, you can select between the following menu forms:
[Information] [Main] [Advanced] [Security] [Power] [Boot] [Exit].
In the main window ②, various settings are displayed or submenus selected.
In the Help window ③ of the respective menu, you can find information on the selected
setup entry.
The operating line ④ contains notes on operation.
You can use the cursor keys [←] left and [→] right to switch between the menu forms.
Menu
Meaning
Information
Device-specific information, for example, product version
Main
Setting system functions
Advanced
Advanced system configuration
Security
Safety functions, for example, setting a password
Power
Determining the switch-on behavior of the device
Boot
Determining boot options, such as boot priority
Exit
Exiting and saving
CPU 1515SP PC (F)
64
Manual, 05/2017, A5E32701806-AC
Functions
8.3 BIOS description
8.3.3.1
Information menu
This menu shows the versions of the device-specific functions.
Keep this information at hand for Customer Support when you have technical questions
regarding your system.
Example
Figure 8-3
Information menu
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
65
Functions
8.3 BIOS description
8.3.3.2
Main menu
Settings in the Main menu
Figure 8-4
Main menu
In the Main menu, you can use the [↑] up and [↓] down arrow keys to select between the
following system setting fields:
Array
Meaning
System Time
Displaying and setting the current time
System Date
Displaying and setting the current calendar date
System Time and System Date
System Time and System Date show the current values. After you have selected the
corresponding field, you can change the following settings, one after the other, using the [+]
and [–] keys:
● For the time of day: Hour: Minute: Second
● For the date: Month/day/year.
You can use the <ENTER> key to switch between the entries within the Date and Time fields
(e.g., from hour to minute).
CPU 1515SP PC (F)
66
Manual, 05/2017, A5E32701806-AC
Functions
8.3 BIOS description
8.3.3.3
Advanced menu
Settings in the Advanced menu
Figure 8-5
Advanced menu
Entry
Meaning
Boot Configuration
Configuring the boot settings
IDE Configuration
Configuring the devices
Video Configuration
Configuring the graphics parameters
CPU Related setting
Configuring CPU parameters
AMD PBS Option
Configuring interfaces
"IDE Configuration" submenu
Entry
Meaning
SATA configure as
Setting the SATA configuration type:
IDE, LEGACY IDE, AHCI
Serial ATA Port 0
Serial ATA Port 0 device configuration
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
67
Functions
8.3 BIOS description
"Video Configuration" submenu
Entry
Meaning
UMA Sharing Memory Size
(256 MB)
Setting the size of the work memory for the graphics processor.
(Unified Memory Architecture; also Shared Memory)
"CPU Related setting" submenu
Entry
Meaning
SVM support
Enabling (Enabled) or disabling (Disabled) Secure Virtual Machine
functionality .
"AMD PBS Option" submenu
Entry
Meaning
Internal LAN Controller
Integrated Ethernet interface (10/100/1000 Mbps)
X2 PN/IE (LAN)
PXE Boot to INT_LAN
Enabling (Enabled) or disabling (Disabled) internal Southbridge
Network Controller.
CPU 1515SP PC (F)
68
Manual, 05/2017, A5E32701806-AC
Functions
8.3 BIOS description
8.3.3.4
Security menu
Settings in the Security menu
Figure 8-6
Security menu
To protect the CPU 1515SP PC (F) against unauthorized access, assign a password.
Supervisor Password
Set Supervisor
Password
Installed
Specific setup fields, including the Supervisor password,
can be modified by the user.
Not installed
Password is disabled.
This field opens a dialog for assigning or changing the password.
Note
Overwriting of the Supervisor password during a BIOS update
A BIOS update overwrites the password.
After a BIOS update, set up the password again.
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
69
Functions
8.3 BIOS description
8.3.3.5
Power menu
Settings in the Power menu
Figure 8-7
Power menu
In the Power menu, you specify the device reaction to a power failure and a Wake Event.
Entry
Meaning
Wake on PME
When activated (Enabled), the device switches itself on when a
Power Management Event occurs. Otherwise, the device remains
switched off.
Auto Wake on S5
When activated (Enabled), the device switches itself on when a
Wake Event occurs. Otherwise, the device remains switched off.
CPU 1515SP PC (F)
70
Manual, 05/2017, A5E32701806-AC
Functions
8.3 BIOS description
8.3.3.6
Boot menu
Entries in the Boot menu
Figure 8-8
Boot menu
In this menu, you define the boot behavior of the device.
Entry
Meaning
Quick Boot
Enabling (Enabled) or disabling (Disabled).
The device starts up faster when this option is enabled, because various hardware function tests are skipped.
Quiet Boot
When this option is disabled, the device boots in text mode.
When it is enabled, a start screen with logo appears.
USB Boot
Booting from connected USB devices permitted/not permitted.
Boot menu > submenu "Boot Device Priority"
In this menu, you define the sequence of the boot media.
Entry
Meaning
Normal Boot Menu
Normal = boot sequence by component type
Advance = individual boot sequence of all components
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
71
Functions
8.3 BIOS description
Boot Device Priority > submenu "Boot Type Order"
Entry
Meaning
Hard Disk Drive
Setting the boot sequence of the group of drives
USB
Setting the boot sequence of the group of USB drives
Others
Setting the boot sequence of the group Others,, e.g. Remote Boot
Device
All connected boot-capable components and their boot position are displayed in this menu.
The boot position of the components can be moved freely.
The component at the top (highest boot priority) is used for booting. If the component is not
available, the system boots from the next component in the list.
You change the boot sequence as follows:
● Select the boot components using the keys <↑>, <↓>
● Move to the required position using the keys <+>, <–>
Note
You can start the Boot Manager by pressing the <F12> key during the boot process.
The Boot Manager shows all available boot components and boots from the device selected
by the user.
"Normal Boot Menu > Advance" setting
Boot capable components which were disconnected and reconnected to the
CPU 1515SP PC (F) during the boot processes, appear in first place in the BIOS in the
"Advance" setting.
Boot Device Priority > submenu "Hard Disk Drive"
The size of the CFast card is displayed in this menu.
CPU 1515SP PC (F)
72
Manual, 05/2017, A5E32701806-AC
Functions
8.3 BIOS description
8.3.3.7
Exit menu
Settings in the Exit menu
Figure 8-9
Exit menu
The setup program is always terminated via the Exit menu.
The menu is used to save or discard the changes made.
Entry
Meaning
Exit Saving Changes
Saves all changes and then starts the system with the new parameters.
Save Change Without Exit
Saves all changes
Exit Discarding Changes
Discards all changes and then restarts the system with the old parameters.
Load Optimal Defaults
Loads the optimum default values
Load Custom Defaults
Loads the default values
Safe Custom Defaults
Saves the default values
Discard Changes
Discards all changes
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
73
Functions
8.3 BIOS description
8.3.4
BIOS setup default settings
Documenting the device configuration
If you change the default setting of the BIOS Setup, then enter this in the following table.
This will ensure that values you set will be readily available if hardware changes are made
later.
We recommend that you print out the table below and keep it in a safe place after you have
made your entries.
Note
The default settings in the BIOS setup depend on the ordered device configuration.
BIOS setup default settings
Menu
System parameters
Default settings
Main
System Time
hh:mm:ss
System Date
MM/TT/JJJJ
Advanced > IDE Configuration
SATA configure as
LEGACY IDE
Serial ATA Port 0
SIMATIC IPC CFast 30
Advanced > Video Configuration
UMA Sharing Memory Size
256 MB
Advanced > CPU Related
setting
SVM Support
Enabled
Advanced > AMD PBS Option
Internal LAN Controller
Auto
PXE Boot to INT_LAN
Disabled
Security
Supervisor Password
Not installed
Set Supervisor Password
Inactive (no password assigned)
Wake on PME
Enabled
Power
Boot
Auto Wake on S5
Disabled
Quick Boot
Enabled
Quiet Boot
Disabled
USB Boot
Disabled
Boot > Boot Device Priority > Normal
Normal Boot Menu
Advance
Normal
Boot > Boot Device Priority
Hard Disk Drive
Boot Type Order
User settings
USB
Others
Hard Disk Drive
SIMATIC IPC CFast 8/16/30
GByte
CPU 1515SP PC (F)
74
Manual, 05/2017, A5E32701806-AC
Functions
8.3 BIOS description
Menu
System parameters
Default settings
Exit
Exit Saving Change
Standard
User settings
Save Change Without Exit
Exit Discarding Changes
Load Optimal Defaults
Load Custom Defaults
Safe Custom Defaults
Discard Changes
8.3.5
BIOS update
With the SIMATIC IPC DiagBase software (included in scope of delivery), you can perform
the following actions:
● Perform a BIOS update.
● Saving and updating the current BIOS version.
● Saving the BIOS settings or loading them from another backup.
For additional information, refer to the online help for the SIMATIC IPC DiagBase software.
Requirements
● The S7-1500 software controller CPU 1505SP (F) must be in STOP mode.
● CPU 1515SP PC (F) must be started in Windows mode.
NOTICE
Malfunctions in the software controllers due to critical actions
If you perform a BIOS update during the operation of the S7-1500 software controller
CPU 1505SP (F), software controller malfunctions can occur that lead to interruptions in
communications and downtimes.
Do not perform BIOS updates or other actions that strongly utilize the hardware resources
during the operation of the CPU 1505SP (F).
Prior to a BIOS update, switch the CPU 1505SP (F) to STOP.
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
75
Functions
8.4 Power options
Performing a BIOS update
1. Start the CPU 1515SP PC (F) in the GRUB menu in Windows mode (see figure
(Page 58)).
→ The PWR LED lights up yellow first, then green.
→ The device carries out the hardware initialization.
2. Follow the BIOS update steps described in the help for SIMATIC IPC DiagBase.
→ The update is performed.
→ You are prompted to restart the device.
3. Us thee Windows function Start > Shut down to shut down the CPU 1515SP PC (F).
→ The PWR LED lights up green first, then yellow.
→ The Windows function closes the Windows operating system and the software
controller.
4. Switch off the power supply at the CPU 1515SP PC (F).
5. Connect the power supply.
6. Wait until the Siemens logo disappears.
→ The CPU 1515SP PC (F) restarts.
NOTICE
Overwriting of the Supervisor password during a BIOS update
A BIOS update overwrites the password.
After a BIOS update, set up the password again in the Security menu under "Set
Supervisor Password".
8.4
Power options
An energy diagram with the name SIMATIC on the CPU 1515SP PC (F). This ensures that
the CPU does not deviate from its maximum clock rate in order not to endanger the real-time
capability of the software controller.
CPU 1515SP PC (F)
76
Manual, 05/2017, A5E32701806-AC
Functions
8.5 Protective functions for data carriers
8.5
Protective functions for data carriers
NOTICE
Data loss
The number of write cycles on CFast cards is limited due to technical reasons.
To prevent data loss, the CFast card must therefore be provided with special protection.
Use a write filter to lengthen of service life of the CFast card and avoid the
CPU 1515SP PC (F).
Write filters
Two write filters are available for Windows Embedded:
● To protect an entire partition of the CFast card, use the Enhanced Write Filter EWF
(Page 78).
Unlike FBWF, you can also use EWF with compressed NTFS data systems.
● Use the File-Based Write Filter FBWF (Page 82), to update specific files dynamically.
The FBWF can be configured more flexibly and enables direct write access without
restart.
NOTICE
Data loss
If both write filters are activated, the EWF blocks direct write access of the FBWF.
Data get lost after a restart of CPU 1515SP PC (F).
Activate only one of the two write filters per partition.
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
77
Functions
8.5 Protective functions for data carriers
8.5.1
Enhanced Write Filter (EWF)
Purpose and function
The Enhanced Write Filter (EWF) allows you to write-protect individual partitions.
EWF is disabled by default on the CPU 1515SP PC (F).
The EWF is activated by means of the pre-installed SIMATIC IPC EWF Manager or the
Windows console application ewfmgr.exe.
SIMATIC IPC EWF Manager
Start the software via Start > All Programs > Siemens Automation > SIMATIC >
EWF Manager.
In the status bar, you can use the SIMATIC IPC EWF Manager icon to check whether the
EWF is active.
Table 8- 1
Icons
Meaning of the icons
Meaning
The partition is protected by the EWF.
EWF is disabled for this partition.
The EWF is currently switched off, but is activated after the restart.
The EWF is currently active, but will be deactivated after the restart.
The filter is active. A Commit command is executed before the next reboot.
The filter is currently active, but is deactivated after the restart.
A Commit command will also be executed before the next reboot.
The operating instructions for the SIMATIC Industrial PC: IPC EWF Manager
(http://support.automation.siemens.com/WW/view/en/50867677) is available on the
CPU 1515SP PC (F) under Start > All Programs > Siemens Automation > Documents >
Manuals.
CPU 1515SP PC (F)
78
Manual, 05/2017, A5E32701806-AC
Functions
8.5 Protective functions for data carriers
Console application ewfmgr.exe
The application is called via the Windows command line (Command Prompt).
The following functions are available, among others, for setting, switching on and switching
off the EWF:
Table 8- 2
Enhanced Write Filter functions
Function
Write-protect drive C: Switching on
Command
ewfmgr c: -enable
Write-protect drive C: disable
(modified data is accepted)
ewfmgr c: -commitanddisable
Modified files on drive C: Accept
ewfmgr c: -commit
Display information about the EWF drive
ewfmgr c:
Display help
ewfmgr /h
Note
The EWF commands for write protection become effective only after a restart.
Note
The EWF command ewfmgr c: -commitanddisable must not be used with the option -Live.
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
79
Functions
8.5 Protective functions for data carriers
Special features when using the EWF
NOTICE
Data loss upon power failure and upon shutdown/restart
If the EWF is active, all changes made on the C drive are lost after power failure and on
shutdown/restart.
Use an UPS to prevent data losses after power failure.
Back up the data in the EWF-RAM overlay to the CFast card before shutting down the
CPU 1515SP PC (F). In the command line, enter the following commands:
ewfmgr c: -commit
Restart the device
Or
ewfmgr c: -commitanddisable
Restart the device
ewfmgr c: -enable
Restart the device
Note
Data loss
If EWF is active and you decline a restart after having set the -commitanddisable or -commit
option, your data is lost after a power failure!
CPU 1515SP PC (F)
80
Manual, 05/2017, A5E32701806-AC
Functions
8.5 Protective functions for data carriers
Note
Disabling automatic daylight saving changes
In systems without central time management and with activated EWF, the time is advanced
or set back by one hour in the daylight saving time or standard time period each time the
system performs a cold or warm restart, due to the system-specific function for automatic
daylight saving changes.
Reason for this behavior: Windows Embedded Standard 7 sets a flag in a registry entry that
indicates completion of the conversion to daylight saving time. Since this file is also
protected against modification by the EWF, the marker is lost during the boot sequence and
the adjustment is made again.
We therefore recommend that you deactivate the automatic adjustment and change the
clock manually.
Proceed as follows:
1. Disable the EWF filter (ewfmgr c: -commitanddisable) and reboot the system.
2. Deactivate the automatic switchover in the Control Panel:
Start > Control Panel > Date and Time > in the tab "Time Zone" clear the check mark for
"Automatically adjust clock for daylight saving changes".
3. Save the change (ewfmgr c: -commit).
4. Switch on the EWF again (ewfmgr c: -commitanddisable) and reboot the system.
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
81
Functions
8.5 Protective functions for data carriers
8.5.2
File-Based Write Filter (FBWF)
Purpose and function
The FBWF allows you to write-protect specific files and folders of a partition.
FBWF is enabled by default on the CPU 1515SP PC (F).
The FBWF is activated by means of the Windows console application fbwfmgr.exe.
NOTICE
Data loss
If both write filters are activated, the EWF blocks direct write access of the FBWF.
Data get lost after a restart of CPU 1515SP PC (F).
Activate only one of the two write filters.
Console application fbwfmgr.exe
The application is called via the Windows command line (Command Prompt).
The following functions, among others, are available for setting, switching on and switching
off the FBWF:
Table 8- 3
File-Based Write Filter
Function
Command
Show FBWF status
fbwfmgr /displayconfig
Activate FBWF after the next restart
fbwfmgr /enable
Write to protected files
fbwfmgr /commit c: \<Path>\<File Name>
Display help
fbwfmgr /?
Defining exclusions:
fbwfmgr /addexclusion c:
\<Path>\<FileName.ext>
•
Add file
•
Add folder
fbwfmgr /addexclusion c: \<Path>
•
Remove file
fbwfmgr /removeexclusion c:
\<Path>\<FileName.ext>
•
Remove folder
fbwfmgr /removeexclusion c: \<Path>
Note
Note:
• The correct notation is as follows:
Drive letter: space character "\" relative file path
• The write protection commands become effective only after a restart.
CPU 1515SP PC (F)
82
Manual, 05/2017, A5E32701806-AC
Functions
8.5 Protective functions for data carriers
Rule for exclusion list
The following sequence applies if you define exclusions for files and folders that do not yet
exist:
● Defining exclusions
● Restart CPU 1515SP PC (F)
● Create file/folder
Display of the partition size with activated FBWF
The partition size displayed in the Explorer does not correspond with the actual size when
the FBWF is active. The size displayed is derived from the amount of memory occupied on
the partition and from memory released by the FBWF. After the maximum size of the overlay
was reached, a message is output warning of insufficient space on the partition.
Reference
Additional information on FBWF is available on the Internet (http://msdn.microsoft.com/enus/library/ff794219(v=winembedded.60).aspx).
Additional information on the topic of partitions is available in the Change partitioning
(Page 85) chapter.
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
83
9
Maintenance
9.1
Backing up and restoring data
Introduction
The operating system and the Runtime software are located on the supplied Restore DVD.
You can use this to restore the original software of the CPU 1515SP PC (F).
If you use functions from the Restore menu, you must acknowledge a security message. For
the functions, 72 hours are available in each case. If the functions are no completed within
this period, the CPU 1515SP PC (F) is automatically restarted.
Save your project to partition D: of the CFast card.
SIMATIC IPC Image & Partition Creator
You can also create your own image of your CFast card. This contains the operating system,
the Runtime software and the complete project loaded from the TIA Portal.
To back up data in Windows Embedded Standard 7, we recommend the software tool
SIMATIC IPC Image & Partition Creator (V3.3 or later). It provides for easy backup and fast
restore of the contents of the CFAST card and of individual partitions (images).
Note
The SIMATIC Image & Partition Creator supports the X2 PN/IE (LAN) interface.
You can procure the SIMATIC IPC Image & Partition Creator:
● via the Siemens online ordering system (http://www.siemens.com/automation/mall).
● Pre-installed on the SIMATIC IPC Service USB flash drives.
For additional information, please refer to the corresponding product documentation.
SIMATIC IPC Service USB flash drive
You can use the SIMATIC IPC Service USB flash drives for data backup and restore.
You obtain these through the Siemens online ordering system
(http://www.siemens.com/automation/mall).
CPU 1515SP PC (F)
84
Manual, 05/2017, A5E32701806-AC
Maintenance
9.2 Change partitioning
9.2
Change partitioning
9.2.1
Partitions in the delivery state
Partitioning the CFast card
The following partitions are set up on the CFast card by default:
Partition
Name
30 GB CFast card
(WES7 E 32Bit/WES7 P 64Bit)
File system
C:
SYSTEM
19.5 GB
NTFS
D:
DATA
8 GB
NTFS
-
-
0.4 GB
RAW
-
WinCCMB
0.04 GB
NTFS
Note
Partitions in Windows Embedded Standard 7
The partitions need to be set again if they are faulty or if the partitioning is to be changed.
NOTICE
CPU volume for software controller (0.4 GB RAW)
Do not change the CPU volume for software controllers.
This is the only way to ensure that the software controller continues to operate without
error.
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
85
Maintenance
9.2 Change partitioning
9.2.2
Change partitioning
If the capacities of the partitions are insufficient, you have the option with Windows 7 to
change the size of the partitions (for example, drive C: extend and drive D: reduce).
Free space must be available in order to extend the partition. You can recognize free space
by the designation "Unallocated". You may have the reduce or delete other partitions to
create space.
Note
Deleting partitions
When partitions are deleted on the data on them are destroyed.
Possible reasons for an expansion of the partition size to drive C:
● Loading security updates for Windows drive C:
● Option of installing large software packages on C, if their size exceeds the available
storage space.
Expand/shrink partition
To expand, for example, Partition C: at the cost of Partition D: follow these steps:
In the Windows start bar, select Start > Control Panel > System and Security >
Administrative Tools > Computer Management > Disk Management. The "Computer
Management" window opens.
Figure 9-1
Computer Management
CPU 1515SP PC (F)
86
Manual, 05/2017, A5E32701806-AC
Maintenance
9.2 Change partitioning
To expand Partition C: you must delete Partition D: first. Right-click on Partition D: and select
"Delete Volume..."
Figure 9-2
Partition D: Delete
The space which was occupied by Partition D: is now available for Partition C: .
Figure 9-3
Partition D: cleared
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
87
Maintenance
9.2 Change partitioning
Now right-click on Partition C: and select "Extend Volume...".
Figure 9-4
Partition C: expand
After selecting the option "Extend Volume...", the "Extend Volume Wizard" appears.
Figure 9-5
Extend Volume Wizard
CPU 1515SP PC (F)
88
Manual, 05/2017, A5E32701806-AC
Maintenance
9.2 Change partitioning
In the following window you have the option to expand Partition C: by all or part of the
available memory. In our example we expand Partition C: by 500 MB.
Figure 9-6
Select memory size
When you have completed the steps of the wizard, the Computer Management window
shows you the new division of the partition sizes.
Figure 9-7
Result of the repartitioning
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
89
Maintenance
9.2 Change partitioning
To reassign the unassigned memory to Partition D: right-click on the unassigned memory
and select "New Simple Volume..."
Figure 9-8
Recreate partition
After selecting the option "New Simple Volume...", the "New Simple Volume Wizard"
appears. Set the required memory size there.
Figure 9-9
Select memory size
CPU 1515SP PC (F)
90
Manual, 05/2017, A5E32701806-AC
Maintenance
9.2 Change partitioning
In the following window, select Drive D:
Figure 9-10
Assign drive letter
Specify the formatting for storing data on the partition.
Figure 9-11
Specify formatting
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
91
Maintenance
9.3 Restoring the delivery state
Once you have defined the formatting, an overview of your selected settings appears. Then
click "Finish" to complete the process.
The "Computer Management" window now shows the new partition sizes.
9.3
Restoring the delivery state
Introduction
The entire image of your operating system and your Runtime software are located on the
supplied Restore DVD. You can use the SIMATIC Restore menu to restore the original
CPU 1515SP PC (F) software.
Alternatively, you can use the Restore menu to create a boot-capable USB stick to restore
the original software without a DVD-ROM drive (see chapter Restoring delivery state using
USB stick (Page 95)).
Note
Restoring existing system partition
If your projects are stored on partition D: you can then use the option "Restore existing
system partition" to restore Partition C: with the operating system and the Runtime software,
without your project data being affected.
Note
Using Multitouch panels
The restoration of the original software is not possible with a Multitouch panel, because the
Multitouch driver is not available until after the installation of the operating system.
CPU 1515SP PC (F)
92
Manual, 05/2017, A5E32701806-AC
Maintenance
9.3 Restoring the delivery state
Requirements
To restore the original software of the CPU 1515SP PC (F), the following is required:
● A CFast card. Minimum size of the CFast card for the CPU 1515SP PC (F):
– WES7 E 32Bit 4GB RAM: 8 GB
– WES7 P 64Bit 4GB RAM: 16 GB
● A DVD drive with external power supply
● The supplied Restore DVD. Alternatively, a bootable USB stick
● A data backup
NOTICE
Data loss
During restoration of the system to delivery state, the CFast card is completely erased and
re-formatted, and is then loaded with the original software. All subsequently modified or
added data, programs, license keys and partitions on the CFast card will be lost.
Back up the data of the CPU 1515SP PC (F), after you have assigned parameters to the
module and if you have made changes to the configuration.
NOTICE
Loss of license keys
Back up the license keys before the restore by dragging these to your USB stick via
Automation License Manager.
After the restart of the CPU 1515SP PC (F), re-install the license keys on the device via the
Automation License Manager.
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
93
Maintenance
9.3 Restoring the delivery state
Restore delivery state of the CPU 1515SP PC (F) with the Restore DVD
Before the restore
1. Switch off the power supply of the CPU.
2. Remove all USB devices from the CPU.
3. Connect a DVD drive with restore DVD to a USB interface of the CPU.
4. Switch on the power supply of the CPU.
→ The CPU is started.
5. Press <F12> to start the Boot Manager.
6. Select the list entry for the DVD drive in the Boot Manager.
7. After the prompt, confirm the start by pressing any key.
→ The loading process is displayed (Windows logo).
→ The SIMATIC Restore menu opens.
– Select a language.
– Select "CPU1515SP PC (F)" or "CPU1515SP PC (F) + HMI".
– Select the option "Completely restore system drive".
→ The original software is restored on Partition C:, Partition D: is deleted.
After the restore
1. Exit the Restore menu.
2. Remove all USB devices.
3. Proceed as described in Initial commissioning (Page 50).
Further procedure
● Reconnect the USB devices.
● Install the license keys.
CPU 1515SP PC (F)
94
Manual, 05/2017, A5E32701806-AC
Maintenance
9.4 Restoring delivery state using USB stick
9.4
Restoring delivery state using USB stick
Introduction
You can use the Restore menu to create a bootable USB stick in order to restore the original
software of the CPU 1515SP PC (F).
Use the SIMATIC IPC Service USB FlashDrive (6AV7672-8JD02-0AA0) for the creation.
Preparing bootable USB stick using PC
NOTICE
Data loss
If you transfer the data from the Restore-DVD to the USB stick, all existing data on the USB
stick is deleted.
You should back up the data on the USB stick before you create the Restore USB stick.
Transferring Restore DVD data to the USB stick
1. Place the Restore DVD into the DVD drive of a PC.
2. Double-click the CD_Menu.exe file in the root directory of the DVD.
3. Select the option " Create USB flash drive".
4. When all the data has been transferred, remove the Restore USB stick safely from the
PC.
Note
If you disturb the User-Interface window during the process (for example, by a mouse click in
the window), the process continues unchanged even if no reaction is recognizable within the
tool interface.
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
95
Maintenance
9.4 Restoring delivery state using USB stick
Restoring delivery state using USB stick
Before the restore
1. Switch off the power supply of the CPU.
2. Remove all USB devices from the CPU.
3. Connect the Restore USB stick directly to the CPU.
4. Switch on the power supply of the CPU.
The CPU is started.
The restore process starts.
5. Press <F12> to start the Boot Manager.
6. Select the list entry for the USB stick as boot medium in the Boot Manager.
7. After the prompt, confirm the start by pressing any key.
The loading process is displayed (Windows logo).
The SIMATIC Restore menu opens.
8. Select a language.
9. Select "CPU 1515SP PC (F)" or "CPU 1515SP PC (F) + HMI".
10.Select the option "Restore delivery state".
The original software is restored.
After the restore
1. Exit the Restore menu.
2. Remove all USB devices.
3. Proceed as described in Initial commissioning.
CPU 1515SP PC (F)
96
Manual, 05/2017, A5E32701806-AC
Maintenance
9.5 Updating software
9.5
Updating software
Note
If you update the software, then always start the CPU 1515SP PC (F) in the GRUB menu in
Windows mode (see Figure (Page 58)).
Information on updating software can be found on the Internet
(https://support.industry.siemens.com/cs/ww/en).
HMI devices
During the installation, make sure that you always use the latest drivers for the HMI devices
used (SIMATIC Flat Panels).
Before you install a new driver version, you must uninstall the old driver version in order to
ensure proper operation.
You can download the current driver software from SIMATIC Product Support.
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
97
Maintenance
9.6 Windows Embedded Standard 7
9.6
Windows Embedded Standard 7
The Windows Embedded Standard 7 operating system is pre-installed on the
CPU 1515SP PC (F). WES7 E 32Bit or WES7 P 64Bit are available depending on the order
option.
The WES7 P version supports multi-touch functionality (gesture control).
Windows language packs
English is available as the basic language for the installation of the Windows operating
system.
With the system version WES7 P 64Bit 4GB RAM of the CPU 1515SP PC (F), other
operating system languages can be installed after the first commissioning. Note that you
need administrator rights to install language packages.
The following language packages are contained on the Restore DVD in
\Packages\x64\LanguagePack:
● Traditional Chinese
● Simplified Chinese
● German
● English
● French
● Italian
● Japanese
● Korean
● Russian
● Spanish
Installing languages
Use the Windows function "Start > Control Panel > Region and Language" to install a
language pack. The installation takes around 45 minutes.
Updates
You can install additional updates at a later time. You can find current information on the
operating system at Widows (http://www.windows.com).
CPU 1515SP PC (F)
98
Manual, 05/2017, A5E32701806-AC
Maintenance
9.7 Sending the device to customer service
9.7
Sending the device to customer service
Before sending
Note
Back up data and remove memory cards
Before you send in the CPU 1515SP PC (F) for repair:
• Create a backup of your data.
• Back up your SIMATIC license keys on a USB stick.
• Remove your SD/MMC cards.
• Remove your CFast card.
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
99
Maintenance
9.8 Removing and inserting the CFast card
9.8
Removing and inserting the CFast card
Introduction
CPU 1515SP PC (F) has one slot for a CFast card. On this card, you will find the operating
system, your Runtime software and, after configuration, the project.
Seal the cover for the CFast card to protect the system against unauthorized access.
You must remove the CFast card before you send in the CPU, for example, for repair.
Requirements
● CPU 1515SP PC (F) is de-energized.
Procedure – Removing the CFast card
1. Remove the seal.
2. Open the cover, using a screwdriver if necessary.
3. Press onto the CFast card.
The card is pressed out of the slot.
4. Pull the card out of the slot.
To do this, grip the rib on the underside of the memory card.
Procedure – Inserting the CFast card
1. Open the cover of the slot, using a screwdriver if necessary.
2. Insert the CFast card into the slot.
3. Press the CFast card into the slot.
The CFast card is properly inserted if the cover can be closed without any resistance.
4. Close the cover.
NOTICE
Unauthorized access
Seal the cover with lead to protect the CFast card with the operating system of the
CPU 1515SP PC (F) against unauthorized access.
CPU 1515SP PC (F)
100
Manual, 05/2017, A5E32701806-AC
Technical data
10.1
10
Standards and approvals
Introduction
The general technical specifications cover the following:
● The standards and test values which the CPU 1515SP PC (F) complies with and fulfils.
● The test criteria according to which the CPU 1515SP PC (F) was tested.
Currently valid markings and approvals
Note
The currently valid markings and approvals are printed on the CPU 1515SP PC (F).
Safety information
WARNING
Risk of personal injury and damage to property.
In potentially explosive atmospheres, injury to persons and material damage may occur if
you disconnect plug-in connections during operation of an ET 200SP.
Always switch off the power to the ET 200SP when disconnecting plug-in connections in
potentially explosive atmospheres.
WARNING
Flying sparks due to loose cables
Risk of explosion in hazardous areas.
USB cables and PROFINET connectors may detach from the device in the case of strong
oscillation and high vibrating loads.
Attach these cables to the strain relief of the device using cable ties.
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
101
Technical data
10.1 Standards and approvals
WARNING
Explosion hazard
If you replace components, compliance with Class I, DIV. 2 can become invalid.
WARNING
Area of application
This device is only suitable for use in Class I, Div. 2, Group A, B, C, D, or in non-hazardous
areas.
CE marking
The CPU 1515SP PC (F) meets the requirements and protection targets of the following EC
guidelines and complies with the harmonized European standards (EN) for programmable
logic controllers published in the official gazettes of the European Community:
● 2006/95/EC "Electrical equipment designed for use within certain voltage limits" (LowVoltage Directive)
● 2004/108/EC "Electromagnetic Compatibility" (EMC Directive)
● 94/9/EC "Equipment and protective systems intended for use in potentially explosive
atmospheres" (Explosion Protection Directive)
The EC declarations of conformity are available for the responsible authorities at:
Siemens AG
Digital Factory
Factory Automation
DF FA AS DH AMB
Postfach 1963
D-92209 Amberg
These are also available for download on the Customer Support Internet pages, keyword
"Declaration of Conformity".
cULus approval
Underwriters Laboratories Inc., complying with
● UL 508 (Industrial Control Equipment)
● CSA C22.2 No. 142 (Process Control Equipment)
OR
CPU 1515SP PC (F)
102
Manual, 05/2017, A5E32701806-AC
Technical data
10.1 Standards and approvals
cULus HAZ. LOC. approval
Underwriters Laboratories Inc., complying with
● UL 508 (Industrial Control Equipment)
● CSA C22.2 No. 142 (Process Control Equipment)
● ANSI/ISA 12.12.01
● CSA C22.2 No. 213 (Hazardous Location)
APPROVED for use in
Class I, Division 2, Group A, B, C, D Tx;
Class I, Zone 2, Group IIC Tx
Installation Instructions for cULus haz.loc.
● WARNING - Explosion Hazard - Do not disconnect while circuit is live unless area is
known to be non-hazardous.
● WARNING - Explosion Hazard - Substitution of components may impair suitability for
Class I, Division 2 or Zone 2.
● This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D; Class I,
Zone 2, Group IIC; or non-hazardous locations.
WARNING: EXPOSURE TO SOME CHEMICALS MAY DEGRADE THE SEALING
PROPERTIES OF MATERIALS USED IN THE RELAYS.
FM approval
Factory Mutual Research (FM) according to
Approval Standard Class Number 3611, 3600, 3810 (ANSI/ISA 82.02.01)
CSA C22.2 No. 213
CSA C22.2 No. 61010-1
APPROVED for use in Class I, Division 2, Group A, B, C, D Tx;
Class I, Zone 2, Group IIC Tx
ATEX approval
in accordance with EN 60079-15 (Electrical apparatus for potentially explosive atmospheres;
Type of protection "n") and EN 60079-0 (Electrical apparatus for potentially explosive gas
atmospheres - Part 0: General Requirements)
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
103
Technical data
10.1 Standards and approvals
IECEx approval
According to IEC 60079-15 (Explosive atmospheres - Part 15: Equipment protection by type
of protection "n") and IEC 60079-0 (Explosive atmospheres - Part 0: Equipment - General
requirements)
Marking for Australia and New Zealand
The ET 200SP distributed I/O system meets the requirements of the standard
AS/NZS CISPR 16.
Korea Certificate KCC-REM-S49-ET200SP
Note that this device corresponds to limit class A in terms of the emission of radio frequency
interference. This device can be used in all areas, except residential areas.
이 기기는 업무용(A급) 전자파 적합기기로서 판매자 또는 사용자는 이 점을 주의하시기
바라며 가정 외의 지역에서 사용하는 것을 목적으로 합니다.
IEC 61131
The CPU 1515SP PC (F) with the S7-1500 software controller CPU 1505SP (F) meets the
requirements and criteria of the standard IEC 61131-2 (programmable logic controllers, part
2: Equipment requirements and tests).
PROFINET standard
The ET 200SP distributed I/O system is based on the standard IEC 61158 Type 10.
PROFIBUS standard
The ET 200SP distributed I/O system is based on the standard IEC 61158 Type 3.
IO-Link standard
The ET 200SP distributed I/O system is based on the standard IEC 61131-9.
CPU 1515SP PC (F)
104
Manual, 05/2017, A5E32701806-AC
Technical data
10.2 Electromagnetic compatibility
Use in industrial environments
SIMATIC products are designed for use in industry.
Table 10- 1
Use in industrial environments
Area of applica- Interference emission requirements
tion
Interference immunity requirements
Industry
EN 61000-6-2: 2005
EN 61000-6-4: 2011
Use in residential areas
Note
The ET 200SP is intended for use in industrial areas; use in residential areas may have an
impact on radio/TV reception.
If you want to use the ET 200SP in residential areas, you must ensure that its radio
frequency interference emission complies with limit class B in accordance with EN 55011.
Suitable measures for achieving RF interference level Class B include, for example:
● Installation of the CPU 1515SP PC (F). in grounded control/switch cabinets
● Use of filters in the supply lines
Reference
The certificates for the markings and approvals can be found on the Internet under
Service&Support (http://www.siemens.com/automation/service&support).
10.2
Electromagnetic compatibility
Definition
Electromagnetic compatibility (EMC) is the ability of an electrical installation to function
satisfactorily in its electromagnetic environment without interfering with that environment.
Among other things, CPU 1515SP PC (F) also meets the requirements of the EMC
legislation for the European single market. The prerequisite for this is that the
CPU 1515SP PC (F) complies with the requirements and guidelines relating to electrical
equipment.
EMC according to NE 21
The CPU 1515SP PC does not meet the EMC specifications of the NAMUR guideline NE21.
The CPU 1515SP PC meets the EMC specifications according to IEC 61131-2 and
IEC 61000-6-2.
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
105
Technical data
10.2 Electromagnetic compatibility
Pulse-shaped disturbance
The following table shows the electromagnetic compatibility of the CPU 1515SP PC (F) with
regard to pulse-shaped interference.
Table 10- 2
Pulse-shaped disturbance
Pulse-shaped disturbance
Test voltage
corresponds to
degree of severity
Electrostatic discharge according
to IEC 61000-4-2.
Air discharge: ±8 kV
3
Contact discharge ± 4 kV
3
Burst pulses (high-speed transient
disturbance) according to
IEC 61000-4-4.
2 kV (power supply cable)
2 kV (signal cable > 30 m)
1 kV (signal cable < 30 m)
3
3
High-energy single pulse (surge) according to IEC 61000-4-5
External protective circuit required (see function manual
Designing interference-free controllers
(http://support.automation.siemens.com/WW/view/en/59193566))
•
asymmetric coupling
2 kV (power supply cable)
DC with protective elements
3
2 kV (signal cable/data cable only > 30 m),
possibly with protective elements
•
symmetric coupling
1 kV (power supply cables) DC with protective
elements
1 kV (signal cable/data cable only > 30 m),
possibly with protective elements
CPU 1515SP PC (F)
106
Manual, 05/2017, A5E32701806-AC
Technical data
10.2 Electromagnetic compatibility
Sinusoidal disturbance
The following table shows the electromagnetic compatibility of the CPU 1515SP PC (F) with
regard to sinusoidal interference.
● RF radiation
Table 10- 3
Sinusoidal disturbance variables with RF radiation
RF radiation according to IEC 61000-4-3/NAMUR 21
Electromagnetic RF field, amplitude-modulated
80 to 1000 MHz; 1.0 to 2.0 GHz
2.0 GHz to 2.7 GHz
10 V/m
3 V/m
corresponds to degree of
severity
3
80% AM (1 kHz)
● RF coupling
Table 10- 4
Sinusoidal disturbance variables with RF coupling
RF coupling according to IEC 61000-4-6
corresponds to degree of
severity
(10 kHz) 150 kHz to 80 MHz
3
10 Vrms unmodulated
80% AM (1 kHz)
150 Ω source impedance
Emission of radio interference
Interference emission of electromagnetic fields according to EN 55016: Limit class A, group
1 (measured at a distance of 10 m).
Table 10- 5
Interference emission of electromagnetic fields according to EN 55016
Frequency
Emitted interference
30 MHz to 230 MHz
< 40 dB (µV/m)Q
230 MHz to 1000 MHz
< 47 dB (µV/m)Q
Interference emission via the AC power supply according to EN 55016: Limit value class A,
Group 1.
Table 10- 6
Interference emission via the AC power supply according to EN 55016
Frequency
Emitted interference
0.15 to 0.5 MHz
<79 dB (µV) Q
<66 dB (µV) M
0.5 to 30 MHz
<73 dB (µV) Q
<60 dB (µV) M
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
107
Technical data
10.3 Shipping and storage conditions
10.3
Shipping and storage conditions
Introduction
The CPU 1515SP PC (F) exceeds requirements in terms of shipping and storage conditions
according to IEC 61131-2. The following information applies to modules that are shipped
and/or stored in their original packaging.
Table 10- 7
Shipping and storage conditions for modules
Type of condition
Permissible range
Free fall (in shipping package)
≤1 m
Temperature
From -40 °C to +70 °C
Barometric pressure
1080 hPa to 660 hPa (corresponds to an altitude of -1000 m
to 3500 m)
Relative humidity
5% to 95%, without condensation
Sinusoidal vibrations according to
IEC 60068-2-6
5 - 8.4 Hz: 3.5 mm
8.4 - 500 Hz: 9.8 m/s2
Shock according to IEC 60068-2-27
250 m/s2, 6 ms, 1000 shocks
10.4
Mechanical and climatic ambient conditions
Note
Restrictions
Deviating from the ambient conditions for the ET 200SP distributed I/O system, the following
restrictions apply to the CPU 1515SP PC (F):
• Mechanical ambient conditions:
– 2 g constant acceleration when using the BusAdapter BA 2×FC
• Ambient temperature:
– 0 to 60 °C for horizontal installation with maximum 32 I/O modules
– 0 to 55 °C for horizontal installation with maximum 64 I/O modules
– 0 to 50 °C for vertical installation with maximum 32 I/O modules
Operating conditions
CPU 1515SP PC (F) is designed for stationary use in weather-proof locations. The operating
conditions exceed the requirements according to DIN IEC 60721-3-3:
● Class 3M3 (mechanical requirements)
● Class 3K3 (climatic requirements)
CPU 1515SP PC (F)
108
Manual, 05/2017, A5E32701806-AC
Technical data
10.4 Mechanical and climatic ambient conditions
Mechanical ambient conditions
The table below shows the mechanical ambient conditions in the form of sinusoidal
oscillations.
Table 10- 8
Mechanical ambient conditions
Frequency band
CPU 1515SP PC (F)
5 ≤ f ≤ 8.4 Hz
3.5 mm amplitude
8.4 ≤ f ≤ 150 Hz
1 g constant acceleration
10 ≤ f ≤ 60 Hz
0.35 mm amplitude
60 ≤ f ≤ 1000 Hz
•
1 g constant acceleration (with BusAdapter BA 2×RJ45)
•
2 g constant acceleration (with BusAdapter BA 2×FC)
Test of mechanical ambient conditions
The table below provides important information with respect to the type and scope of the test
of ambient mechanical conditions.
Table 10- 9
Test of mechanical ambient conditions
Condition tested
Test Standard
Comment
Vibration
Vibration test according to IEC 60068-2-6
(sine)
Type of oscillation: Frequency sweeps with a rate of change of 1 octave/minute.
BA 2×RJ45
•
5 Hz ≤ f ≤ 8.4 Hz, 3.5 mm constant amplitude
• 8.4 Hz ≤ f ≤ 150 Hz, 1 g constant acceleration
BA 2×FC
•
10 Hz ≤ f ≤ 60 Hz, 0.35 mm constant amplitude
• 60 Hz ≤ f ≤ 1000 Hz, 2 g constant acceleration
Duration of vibration: 10 frequency sweeps per axis in each of 3 vertically
aligned axes
Shock
Shock, tested according to IEC 60068-2-27
Type of shock: Half-sine
Shock intensity: 150 m/s2 peak value, 11 ms duration
Direction of shock: 3 shocks in each direction (+/-) at each of 3 vertically
aligned axes
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
109
Technical data
10.5 Information on insulation, protection class, degree of protection and rated voltage
Climatic ambient conditions
You may use the CPU 1515SP PC (F) under the following climatic, ambient conditions.
Table 10- 10 Climatic ambient conditions
Ambient conditions
Permissible range
Temperature:
Horizontal mounting position:
•
from 0 to 60 °C
For configuration with 32 I/O modules and 3 x
100 mA USB load
•
from 0 to 55 °C
For configuration with 64 I/O modules and 2 x
500 mA + 1 x 100 mA USB load
•
0 to 50 °C
For configuration with 32 I/O modules and 3 x
100 mA USB load
Vertical installation:
Comments
Permitted temperature change
10 K/h
-
Relative humidity
from 10 to 95%
Without condensation, corresponds to relative humidity (RH) class 2 according to IEC
61131 part 2
Barometric pressure
1080 hPa to 795 hPa
Corresponds to an altitude of -1000 m
to 2000 m
Concentration of pollutants
SO2: <0.5 ppm;
RH <60 %, no condensation
H2S: <0.1 ppm;
RH <60 %, no condensation
-
ISA-S71.04 severity level G1; G2; G3
-
10.5
Information on insulation, protection class, degree of protection and
rated voltage
Insulation
The insulation is designed according to the requirements of EN 61131-2: 2007.
Note
For modules with 24 V DC supply voltage, the electrical isolation is designed for max. 60 V
AC / 75 V DC and basic insulation is designed according to EN 61131-2: 2007.
Pollution degree/overvoltage category according to IEC 61131
● Pollution degree 2
● Overvoltage category: II
CPU 1515SP PC (F)
110
Manual, 05/2017, A5E32701806-AC
Technical data
10.6 Use of the ET 200SP in zone 2 potentially explosive atmospheres
Protection class according to IEC 61131-2:2007
CPU 1515SP PC (F) fulfils the protection class I and contains parts of protection class II and
III.
The grounding of the mounting rail must meet the requirements for functional earth FE.
The installation location (e.g. enclosure, control cabinet) must have a protective conductor
connection that meets the standard to maintain protection class I.
Degree of protection IP20
Degree of protection IP20 according to IEC 60529, i.e.:
● Protection against contact with standard probe
● Protection against foreign objects with diameters in excess of 12.5 mm
● No protection against water
Rated voltage for operation
CPU 1515SP PC (F) works with the rated voltage and corresponding tolerances listed in the
following table.
Table 10- 11 Rated voltage for operation
Rated voltage
Tolerance range
24 V
19.2 to 28.8 V DC 1
18.5 to 30.2 V DC 2
10.6
1
Static value: Creation as functional extra-low voltage with safe electrical isolation in accordance
with IEC 60364-4-41
2
Dynamic value: including ripple, for example, with three-phase bridge rectification
Use of the ET 200SP in zone 2 potentially explosive atmospheres
See product information Use of subassemblies/modules in a Zone 2 Hazardous Area
(http://support.automation.siemens.com/WW/view/en/19692172).
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
111
Technical data
10.7 Module data
10.7
Module data
10.7.1
CPU 1515SP PC, system version WES7 E 32Bit 4GB RAM
CPU 1515SP PC, system version WES7 E 32Bit 4GB RAM
6ES7677-2AA31-0EB0
General information
Product type designation
CPU 1515SP PC
HW release number
FS06
Firmware version
V2.1
Engineering with
STEP 7 TIA Portal can be configured/integrated as of version V14 SP1
PC configuration
Processor
Dual-Core 1 GHz, AMD G Series APU T40E
Main memory
4 GB RAM
Flash disk
30 GB
Operating systems
Windows Embedded Standard 7 E 32 bit
Installed SW
Visualization
No
Controller
S7-1500 Software Controller CPU 1505SP V2.1
Operator controls
Mode selector
1
Supply voltage
Type of supply voltage
24 V DC
Low limit of permitted range (DC)
19.2 V
High limit of permitted range (DC)
28.8 V
Reverse polarity protection
Yes
Power and voltage failure backup
Power/voltage failure backup time
5 ms
Input current
Current consumption (rated value)
1.5 A; full processor load, incl. ET 200SP modules and USB
use
Current consumption (in no-load operation), typ.
0.6 A
Inrush current, max.
4.7 A; rated value
Power
Power consumption, max.
36 W; incl. ET 200SP modules and USB use
Incoming power to the backplane bus
8.75 W
Power loss
Power loss, typ.
15 W; without ET 200SP modules and without USB use
CPU 1515SP PC (F)
112
Manual, 05/2017, A5E32701806-AC
Technical data
10.7 Module data
6ES7677-2AA31-0EB0
Memory
Type of memory
DDR3-SDRAM
CFast memory card
Yes; 30 GB flash memory
SIMATIC memory card required
No
Work memory
Integrated (for program)
1 MB
Integrated (for data)
5 MB
Integrated (for ODK application)
10 MB
Load memory
Integrated (on PC mass storage medium)
320 MB
Buffering
with UPS
Yes; all retentive declared memory areas
with non-volatile memory
Yes
Hardware configuration
integrated power supply
Yes
Number of DP masters
Via CM
1
Racks
Modules per rack, max.
64; CPU 1515SP PC + 64 module + server module
Number of rows, max.
1
Time-of-day
Clock
Type
Hardware clock
Buffering time
6 wk; at 40 °C ambient temperature, typ.
Deviation per day, max.
10 s; typ.: 2 s
Interfaces
Number of Industrial Ethernet interfaces
2
Number of PROFINET interfaces
1
Number of PROFIBUS interfaces
1
Number of interfaces RS 485
1; via CM DP module
Number of USB interfaces
3; 3x USB 2.0 front, 500 mA each – of which 2 x 500 mA
and 1 x 100 mA simultaneously
Number of SD card slots
1
Video interfaces
Graphic interface
1x DVI-I
1st interface
Interface hardware
Number of ports
2
Integrated switch
Yes
RJ 45 (Ethernet)
Yes; via BusAdapter BA 2x RJ45
•
Transmission rate, max.
100 Mbps
•
Industrial Ethernet status LED
Yes
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
113
Technical data
10.7 Module data
6ES7677-2AA31-0EB0
2nd interface
Interface hardware
Number of ports
1
RJ 45 (Ethernet)
Yes; integrated
•
Transmission rate, max.
1000 Mbps
•
Industrial Ethernet status LED
No
3rd interface
Interface hardware
RS 485
Yes
Interface hardware
RJ 45 (Ethernet)
100 Mbps
Yes; for 1st Interface X1
1000 Mbps
Yes; for 2nd Interface X2
Autonegotiation
Yes
Autocrossing
Yes
RS 485
Transmission rate, max.
12 Mbps
Interrupts/diagnostics/status information
LED diagnostics display
RUN/STOP LED
Yes
ERROR LED
Yes
MAINT LED
Yes
Ambient conditions
Ambient temperature in operation
Min.
0 °C
Max.
Up to 60 °C with max. 32 ET 200SP modules and
3x 100 mA USB load; up to 55 °C with max 64 ET 200SP
modules and 2x max. 500 mA and 1x max. 100 mA USB
load
Horizontal installation, min.
0 °C
Horizontal installation, max.
60 °C
Vertical installation, min.
0 °C
Vertical installation, max.
50 °C; with max. 32 ET 200SP modules and 3x 100 mA
USB load
Ambient temperature during storage / transport
Min.
-40 °C
Max.
70 °C
I/O / Options
I/O
•
SD card
Optional for additional mass storage
CPU 1515SP PC (F)
114
Manual, 05/2017, A5E32701806-AC
Technical data
10.7 Module data
6ES7677-2AA31-0EB0
Dimensions
Width
160 mm
Height
117 mm
Depth
75 mm
Weights
Weight, approx.
10.7.2
0.83 kg
CPU 1515SP PC F, system version WES7 E 32Bit 4GB RAM
CPU 1515SP PC F, system version WES7 E 32Bit 4GB RAM
6ES7677-2FA31-0EB0
General information
Product type designation
CPU 1515SP PC F
Firmware version
V2.1
Engineering with
STEP 7 TIA Portal can be configured/integrated as of version V14 SP1
PC configuration
Processor
Dual-Core 1 GHz, AMD G Series APU T40E
Main memory
4 GB RAM
Flash disk
30 GB
Operating systems
Windows Embedded Standard 7 E 32 bit
Installed SW
Visualization
No
Controller
S7-1500 Software Controller CPU 1505SP F
Operator controls
Mode selector
1
Supply voltage
Type of supply voltage
24 V DC
Low limit of permitted range (DC)
19.2 V
High limit of permitted range (DC)
28.8 V
Reverse polarity protection
Yes
Power and voltage failure backup
Power/voltage failure backup time
5 ms
Input current
Current consumption (rated value)
1.5 A; full processor load, incl. ET 200SP modules and USB
use
Current consumption (in no-load operation), typ.
0.6 A
Inrush current, max.
4.7 A; rated value
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
115
Technical data
10.7 Module data
6ES7677-2FA31-0EB0
Power
Power consumption, max.
36 W; incl. ET 200SP modules and USB use
Incoming power to the backplane bus
8.75 W
Power loss
Power loss, typ.
15 W; without ET 200SP modules and without USB use
Memory
Type of memory
DDR3-SDRAM
CFast memory card
Yes; 30 GB flash memory
SIMATIC memory card required
No
Work memory
Integrated (for program)
1.5 MB
Integrated (for data)
5 MB
Integrated (for ODK application)
10 MB
Load memory
Integrated (on PC mass storage medium)
320 MB
Buffering
with UPS
Yes; all retentive declared memory areas
with non-volatile memory
Yes
Hardware configuration
integrated power supply
Yes
Number of DP masters
Via CM
1
Racks
Modules per rack, max.
64; CPU 1515SP PC + 64 module + server module
Number of rows, max.
1
Time-of-day
Clock
Type
Hardware clock
Buffering time
6 wk; at 40 °C ambient temperature, typ.
Deviation per day, max.
10 s; typ.: 2 s
Interfaces
Number of Industrial Ethernet interfaces
2
Number of PROFINET interfaces
1
Number of PROFIBUS interfaces
1
Number of interfaces RS 485
1; via CM DP module
Number of USB interfaces
3; 3x USB 2.0 front, 500 mA each – of which 2 x 500 mA
and 1 x 100 mA simultaneously
Number of SD card slots
1
Video interfaces
Graphics interface
1x DVI-I
CPU 1515SP PC (F)
116
Manual, 05/2017, A5E32701806-AC
Technical data
10.7 Module data
6ES7677-2FA31-0EB0
1st interface
Interface hardware
Number of ports
2
integrated switch
Yes
RJ 45 (Ethernet)
Yes; via BusAdapter BA 2x RJ45
•
Transmission rate, max.
100 Mbps
•
Industrial Ethernet status LED
Yes
2nd interface
Interface hardware
Number of ports
1
RJ 45 (Ethernet)
Yes; integrated
•
Transmission rate, max.
1000 Mbps
•
Industrial Ethernet status LED
No
3rd interface
Interface hardware
RS 485
Yes
Interface hardware
RJ 45 (Ethernet)
100 Mbps
Yes; for 1st Interface X1
1000 Mbps
Yes; for 2nd Interface X2
Autonegotiation
Yes
Autocrossing
Yes
RS 485
Transmission rate, max.
12 Mbps
Interrupts/diagnostics/status information
LED diagnostics display
RUN/STOP LED
Yes
ERROR LED
Yes
MAINT LED
Yes
Ambient conditions
Ambient temperature in operation
Min.
0 °C
Max.
Up to 60 °C with max. 32 ET 200SP modules and
3x 100 mA USB load; up to 55 °C with max 64 ET 200SP
modules and 2x max. 500 mA and 1x max. 100 mA USB
load
Horizontal installation, min.
0 °C
Horizontal installation, max.
60 °C
Vertical installation, min.
0 °C
Vertical installation, max.
50 °C; with max. 32 ET 200SP modules and 3x 100 mA
USB load
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
117
Technical data
10.7 Module data
6ES7677-2FA31-0EB0
Ambient temperature during storage / transport
Min.
-40 °C
Max.
70 °C
I/O / Options
I/O
•
optional for additional mass storage
SD card
Dimensions
Width
160 mm
Height
117 mm
Depth
75 mm
Weights
Weight, approx.
10.7.3
0.83 kg
CPU 1515SP PC, system version WES7 E 32Bit 4GB RAM - spare part
CPU 1515SP PC, system version WES7 E 32Bit 4GB RAM - spare part
6ES7677-2AA40-0AA0
General information
Product type designation
CPU 1515SP PC
Engineering with
STEP 7 TIA Portal can be configured/integrated as of version as of STEP 7 V14
PC configuration
Processor
Dual-Core 1 GHz, AMD G Series APU T40E
Main memory
4 GB RAM
Installed SW
Visualization
No
Controller
No
Operator controls
Mode selector
1
Supply voltage
Type of supply voltage
24 V DC
Low limit of permitted range (DC)
19.2 V
High limit of permitted range (DC)
28.8 V
Reverse polarity protection
Yes
Power and voltage failure backup
Power/voltage failure backup time
5 ms
CPU 1515SP PC (F)
118
Manual, 05/2017, A5E32701806-AC
Technical data
10.7 Module data
6ES7677-2AA40-0AA0
Input current
Current consumption (rated value)
1.5 A; full processor load, incl. ET 200SP modules and USB
use
Current consumption (in no-load operation), typ.
0.6 A
Inrush current, max.
4.7 A; rated value
Power
Power consumption, max.
36 W; incl. ET 200SP modules and USB use
Incoming power to the backplane bus
8.75 W
Power loss
Power loss, typ.
15 W; without ET 200SP modules and without USB use
Memory
Type of memory
DDR3-SDRAM
CFast memory card
No
Work memory
Integrated
4 GB
Hardware configuration
integrated power supply
Yes
Number of DP masters
Via CM
1
Racks
Modules per rack, max.
64; CPU + 64 Module + server module (mounting width
max. 1 m)
Number of rows, max.
1
Time-of-day
Clock
Type
Hardware clock
Buffering time
6 wk; at 40 °C ambient temperature, typ.
Deviation per day, max.
10 s; typ.: 2 s
Interfaces
Number of Industrial Ethernet interfaces
2
Number of PROFINET interfaces
1
Number of PROFIBUS interfaces
1; via CM DP module
Number of interfaces RS 485
1; via CM DP module
Number of USB interfaces
3; 3x USB 2.0 front, 500 mA each – of which 2 x 500 mA
and 1 x 100 mA simultaneously
Number of SD card slots
1
Video interfaces
Graphics interface
1x DVI-I
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
119
Technical data
10.7 Module data
6ES7677-2AA40-0AA0
1st interface
Interface hardware
Number of ports
2
integrated switch
Yes
RJ 45 (Ethernet)
Yes; via BusAdapter BA 2x RJ45
•
Transmission rate, max.
100 Mbps
•
Industrial Ethernet status LED
Yes
2nd interface
Interface hardware
Number of ports
1
RJ 45 (Ethernet)
Yes; integrated
•
Transmission rate, max.
1000 Mbps
•
Industrial Ethernet status LED
No
3rd interface
Interface hardware
RS 485
Yes; via CM DP module
Interface hardware
RJ 45 (Ethernet)
100 Mbps
Yes; for 1st Interface X1
1000 Mbps
Yes; for 2nd Interface X2
Autonegotiation
Yes
Autocrossing
Yes
RS 485
Transmission rate, max.
12 Mbps
Ambient conditions
Ambient temperature in operation
Min.
0 °C
Max.
Up to 60 °C with max. 32 ET 200SP modules and
3x 100 mA USB load; up to 55 °C with max 64 ET 200SP
modules and 2x max. 500 mA and 1x max. 100 mA USB
load
Horizontal installation, min.
0 °C
Horizontal installation, max.
60 °C
Vertical installation, min.
0 °C
Vertical installation, max.
50 °C; with max. 32 ET 200SP modules and 3x 100 mA
USB load
Ambient temperature during storage / transport
Min.
-40 °C
Max.
70 °C
CPU 1515SP PC (F)
120
Manual, 05/2017, A5E32701806-AC
Technical data
10.7 Module data
6ES7677-2AA40-0AA0
I/O / Options
I/O
•
optional for additional mass storage
SD card
Dimensions
Width
160 mm
Height
117 mm
Depth
75 mm
Weights
Weight, approx.
10.7.4
0.83 kg
CPU 1515SP PC, system version WES7 P 64Bit 4GB RAM
CPU 1515SP PC, system version WES7 P 64Bit 4GB RAM
6ES7677-2AA41-0FB0
General information
Product type designation
CPU 1515SP PC
HW release number
FS05
Firmware version
V2.1
Engineering with
STEP 7 TIA Portal can be configured/integrated as of version V14 SP1
PC configuration
Processor
Dual-Core 1 GHz, AMD G Series APU T40E
Main memory
4 GB RAM
Flash disk
30 GB
Operating systems
Windows Embedded Standard 7 P 64 bit
Installed SW
Visualization
No
Controller
S7-1500 Software Controller CPU 1505SP V2.1
Operator controls
Mode selector
1
Supply voltage
Type of supply voltage
24 V DC
Low limit of permitted range (DC)
19.2 V
High limit of permitted range (DC)
28.8 V
Reverse polarity protection
Yes
Power and voltage failure backup
Power/voltage failure backup time
5 ms
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
121
Technical data
10.7 Module data
6ES7677-2AA41-0FB0
Input current
Current consumption (rated value)
1.5 A; full processor load, incl. ET 200SP modules and USB
use
Current consumption (in no-load operation), typ.
0.6 A
Inrush current, max.
4.7 A; rated value
Power
Power consumption, max.
36 W; incl. ET 200SP modules and USB use
Incoming power to the backplane bus
8.75 W
Power loss
Power loss, typ.
15 W; without ET 200SP modules and without USB use
Memory
Type of memory
DDR3-SDRAM
CFast memory card
Yes; 30 GB flash memory
SIMATIC memory card required
No
Work memory
Integrated (for program)
1 MB
Integrated (for data)
5 MB
Integrated (for ODK application)
10 MB
Load memory
Integrated (on PC mass storage medium)
320 MB
Buffering
with UPS
Yes; all retentive declared memory areas
with non-volatile memory
Yes
Hardware configuration
integrated power supply
Yes
Number of DP masters
Via CM
1
Racks
Modules per rack, max.
64; CPU 1515SP PC + 64 module + server module
Number of rows, max.
1
Time-of-day
Clock
Type
Hardware clock
Buffering time
6 wk; at 40 °C ambient temperature, typ.
Deviation per day, max.
10 s; typ.: 2 s
Interfaces
Number of Industrial Ethernet interfaces
2
Number of PROFINET interfaces
1
Number of PROFIBUS interfaces
1
Number of interfaces RS 485
1; via CM DP module
Number of USB interfaces
3; 3x USB 2.0 front, 500 mA each – of which 2 x 500 mA
and 1 x 100 mA simultaneously
Number of SD card slots
1
CPU 1515SP PC (F)
122
Manual, 05/2017, A5E32701806-AC
Technical data
10.7 Module data
6ES7677-2AA41-0FB0
Video interfaces
Graphics interface
1x DVI-I
1st interface
Interface hardware
Number of ports
2
integrated switch
Yes
RJ 45 (Ethernet)
Yes; via BusAdapter BA 2x RJ45
•
Transmission rate, max.
100 Mbps
•
Industrial Ethernet status LED
Yes
2nd interface
Interface hardware
Number of ports
1
RJ 45 (Ethernet)
Yes; integrated
•
Transmission rate, max.
1000 Mbps
•
Industrial Ethernet status LED
No
3rd interface
Interface hardware
RS 485
Yes
Interface hardware
RJ 45 (Ethernet)
100 Mbps
Yes; for 1st Interface X1
1000 Mbps
Yes; for 2nd Interface X2
Autonegotiation
Yes
Autocrossing
Yes
RS 485
Transmission rate, max.
12 Mbps
Interrupts/diagnostics/status information
LED diagnostics display
RUN/STOP LED
Yes
ERROR LED
Yes
MAINT LED
Yes
Ambient conditions
Ambient temperature in operation
Min.
0 °C
Max.
Up to 60 °C with max. 32 ET 200SP modules and
3x 100 mA USB load; up to 55 °C with max 64 ET 200SP
modules and 2x max. 500 mA and 1x max. 100 mA USB
load
Horizontal installation, min.
0 °C
Horizontal installation, max.
60 °C
Vertical installation, min.
0 °C
Vertical installation, max.
50 °C; with max. 32 ET 200SP modules and 3x 100 mA
USB load
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
123
Technical data
10.7 Module data
6ES7677-2AA41-0FB0
Ambient temperature during storage / transport
Min.
-40 °C
Max.
70 °C
I/O / Options
I/O
•
optional for additional mass storage
SD card
Dimensions
Width
160 mm
Height
117 mm
Depth
75 mm
Weights
Weight, approx.
10.7.5
0.83 kg
CPU 1515SP PC F, system version WES7 P 64Bit 4GB RAM
CPU 1515SP PC F, system version WES7 P 64Bit 4GB RAM
6ES7677-2FA41-0FB0
General information
Product type designation
CPU 1515SP PC
HW release number
FS02
Firmware version
V2.1
Engineering with
STEP 7 TIA Portal can be configured/integrated as of version V14 SP1
PC configuration
Processor
Dual-Core 1 GHz, AMD G Series APU T40E
Main memory
4 GB RAM
Flash disk
30 GB
Operating systems
Windows Embedded Standard 7 P 64 bit
Installed SW
Visualization
No
Controller
S7-1500 Software Controller CPU 1505SP F
Operator controls
Mode selector
1
Supply voltage
Type of supply voltage
24 V DC
Low limit of permitted range (DC)
19.2 V
High limit of permitted range (DC)
28.8 V
Reverse polarity protection
Yes
CPU 1515SP PC (F)
124
Manual, 05/2017, A5E32701806-AC
Technical data
10.7 Module data
6ES7677-2FA41-0FB0
Power and voltage failure backup
Power/voltage failure backup time
5 ms
Input current
Current consumption (rated value)
1.5 A; full processor load, incl. ET 200SP modules and USB
use
Current consumption (in no-load operation), typ.
0.6 A
Inrush current, max.
4.7 A; rated value
Power
Power consumption, max.
36 W; incl. ET 200SP modules and USB use
Incoming power to the backplane bus
8.75 W
Power loss
Power loss, typ.
15 W; without ET 200SP modules and without USB use
Memory
Type of memory
DDR3-SDRAM
CFast memory card
Yes; 30 GB flash memory
SIMATIC memory card required
No
Work memory
Integrated (for program)
1.5 MB
Integrated (for data)
5 MB
Integrated (for ODK application)
10 MB
Load memory
Integrated (on PC mass storage medium)
320 MB
Buffering
with UPS
Yes; all retentive declared memory areas
with non-volatile memory
Yes
Hardware configuration
integrated power supply
Yes
Number of DP masters
Via CM
1
Racks
Modules per rack, max.
64; CPU 1515SP PC + 64 module + server module
Number of rows, max.
1
Time-of-day
Clock
Type
Hardware clock
Buffering time
6 wk; at 40 °C ambient temperature, typ.
Deviation per day, max.
10 s; typ.: 2 s
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
125
Technical data
10.7 Module data
6ES7677-2FA41-0FB0
Interfaces
Number of Industrial Ethernet interfaces
2
Number of PROFINET interfaces
1
Number of PROFIBUS interfaces
1
Number of interfaces RS 485
1; via CM DP module
Number of USB interfaces
3; 3x USB 2.0 front, 500 mA each – of which 2 x 500 mA
and 1 x 100 mA simultaneously
Number of SD card slots
1
Video interfaces
Graphics interface
1x DVI-I
1st interface
Interface hardware
Number of ports
2
integrated switch
Yes
RJ 45 (Ethernet)
Yes; via BusAdapter BA 2x RJ45
•
Transmission rate, max.
100 Mbps
•
Industrial Ethernet status LED
Yes
2nd interface
Interface hardware
Number of ports
1
RJ 45 (Ethernet)
Yes; integrated
•
Transmission rate, max.
1000 Mbps
•
Industrial Ethernet status LED
No
3rd interface
Interface hardware
RS 485
Yes
Interface hardware
RJ 45 (Ethernet)
100 Mbps
Yes; for 1st Interface X1
1000 Mbps
Yes; for 2nd Interface X2
Autonegotiation
Yes
Autocrossing
Yes
RS 485
Transmission rate, max.
12 Mbps
Interrupts/diagnostics/status information
LED diagnostics display
RUN/STOP LED
Yes
ERROR LED
Yes
MAINT LED
Yes
CPU 1515SP PC (F)
126
Manual, 05/2017, A5E32701806-AC
Technical data
10.7 Module data
6ES7677-2FA41-0FB0
Ambient conditions
Ambient temperature in operation
Min.
0 °C
Max.
Up to 60 °C with max. 32 ET 200SP modules and
3x 100 mA USB load; up to 55 °C with max 64 ET 200SP
modules and 2x max. 500 mA and 1x max. 100 mA USB
load
Horizontal installation, min.
0 °C
Horizontal installation, max.
60 °C
Vertical installation, min.
0 °C
Vertical installation, max.
50 °C; with max. 32 ET 200SP modules and 3x 100 mA
USB load
Ambient temperature during storage / transport
Min.
-40 °C
Max.
70 °C
I/O / Options
I/O
•
optional for additional mass storage
SD card
Dimensions
Width
160 mm
Height
117 mm
Depth
75 mm
Weights
Weight, approx.
10.7.6
0.83 kg
CPU 1515SP PC, system version WES7 E 64Bit 4GB RAM - spare part
CPU 1515SP PC, system version WES7 E 64Bit 4GB RAM - spare part
6ES7677-2AA40-0AA0
General information
Product type designation
CPU 1515SP PC
Engineering with
STEP 7 TIA Portal can be configured/integrated as of version as of STEP 7 V14
PC configuration
Processor
Dual-Core 1 GHz, AMD G Series APU T40E
Main memory
4 GB RAM
Installed SW
Visualization
No
Controller
No
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
127
Technical data
10.7 Module data
6ES7677-2AA40-0AA0
Operator controls
Mode selector
1
Supply voltage
Type of supply voltage
24 V DC
Low limit of permitted range (DC)
19.2 V
High limit of permitted range (DC)
28.8 V
Reverse polarity protection
Yes
Power and voltage failure backup
Power/voltage failure backup time
5 ms
Input current
Current consumption (rated value)
1.5 A; full processor load, incl. ET 200SP modules and USB
use
Current consumption (in no-load operation), typ.
0.6 A
Inrush current, max.
4.7 A; rated value
Power
Power consumption, max.
36 W; incl. ET 200SP modules and USB use
Incoming power to the backplane bus
8.75 W
Power loss
Power loss, typ.
15 W; without ET 200SP modules and without USB use
Memory
Type of memory
DDR3-SDRAM
CFast memory card
No
Work memory
Integrated
4 GB
Hardware configuration
integrated power supply
Yes
Number of DP masters
Via CM
1
Racks
Modules per rack, max.
64; CPU + 64 Module + server module (mounting width
max. 1 m)
Number of rows, max.
1
Time-of-day
Clock
Type
Hardware clock
Buffering time
6 wk; at 40 °C ambient temperature, typ.
Deviation per day, max.
10 s; typ.: 2 s
Interfaces
Number of Industrial Ethernet interfaces
2
Number of PROFINET interfaces
1
Number of PROFIBUS interfaces
1; via CM DP module
Number of interfaces RS 485
1; via CM DP module
Number of USB interfaces
3; 3x USB 2.0 front, 500 mA each – of which 2 x 500 mA
and 1 x 100 mA simultaneously
CPU 1515SP PC (F)
128
Manual, 05/2017, A5E32701806-AC
Technical data
10.7 Module data
6ES7677-2AA40-0AA0
Number of SD card slots
1
Video interfaces
Graphics interface
1x DVI-I
1st interface
Interface hardware
Number of ports
2
integrated switch
Yes
RJ 45 (Ethernet)
Yes; via BusAdapter BA 2x RJ45
•
Transmission rate, max.
100 Mbps
•
Industrial Ethernet status LED
Yes
2nd interface
Interface hardware
Number of ports
1
RJ 45 (Ethernet)
Yes; integrated
•
Transmission rate, max.
1000 Mbps
•
Industrial Ethernet status LED
No
3rd interface
Interface hardware
RS 485
Yes; via CM DP module
Interface hardware
RJ 45 (Ethernet)
100 Mbps
Yes; for 1st Interface X1
1000 Mbps
Yes; for 2nd Interface X2
Autonegotiation
Yes
Autocrossing
Yes
RS 485
Transmission rate, max.
12 Mbps
Ambient conditions
Ambient temperature in operation
Min.
0 °C
Max.
Up to 60 °C with max. 32 ET 200SP modules and
3x 100 mA USB load; up to 55 °C with max 64 ET 200SP
modules and 2x max. 500 mA and 1x max. 100 mA USB
load
Horizontal installation, min.
0 °C
Horizontal installation, max.
60 °C
Vertical installation, min.
0 °C
Vertical installation, max.
50 °C; with max. 32 ET 200SP modules and 3x 100 mA
USB load
Ambient temperature during storage / transport
Min.
-40 °C
Max.
70 °C
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
129
Technical data
10.7 Module data
6ES7677-2AA40-0AA0
I/O / Options
I/O
•
optional for additional mass storage
SD card
Dimensions
Width
160 mm
Height
117 mm
Depth
75 mm
Weights
Weight, approx.
10.7.7
0.83 kg
CPU 1515SP PC (F) + HMI
The technical specifications of the following devices modules can be found in the product
information under (http://support.automation.siemens.com/WW/view/en/104117388).
ET 200SP Open Controller
Article number
System version WES7 P 64Bit 4GB RAM
CPU 1515SP PC
CPU 1515SP PC + HMI 128PT
6ES7677-2AA41-0FK0
CPU 1515SP PC + HMI 512PT
6ES7677-2AA41-0FL0
CPU 1515SP PC + HMI 2048PT
6ES7677-2AA41-0FM0
CPU 1515SP PC F
CPU 1515SP PC F + HMI 128PT
6ES7677-2FA41-0FK0
CPU 1515SP PC F + HMI 512PT
6ES7677-2FA41-0FL0
CPU 1515SP PC F + HMI 2048PT
6ES7677-2FA41-0FM0
10.7.8
S7-1500 Software Controller CPU 1505SP (F)
CPU 1505SP (F) is a PC-based controller of the SIMATIC S7-1500 Software Controller
family. For more information about the CPU 1505SP (F), refer to the corresponding manual
at (https://support.industry.siemens.com/cs/ww/en/view/109740725). For the
CPU 1505SP F, also note the information in the F product information at
(https://support.industry.siemens.com/cs/ww/en/view/109478599).
Technical specifications
You can find all technical specifications on CPU 1505SP with the article number
6ES7672-5DC01-0YA0 under (https://support.industry.siemens.com/cs/ww/en/pv/6ES76725DC01-0YA0/td). You can find all technical specifications on CPU 1505SP F with the article
number 6ES7672-5SC01-0YA0 under
(https://support.industry.siemens.com/cs/ww/en/pv/6ES7672-5SC01-0YA0/td).
CPU 1515SP PC (F)
130
Manual, 05/2017, A5E32701806-AC
Technical data
10.8 Dimension drawings
10.8
Dimension drawings
10.8.1
CPU 1515SP PC (F)
This section contains a dimension drawing of the module mounted on a mounting rail.
Always observe the specified dimensions for installation in cabinets.
Dimension drawings of the CPU 1515SP PC (F).
Figure 10-1
Dimension drawing of CPU 1515SP PC, front view
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
131
Technical data
10.8 Dimension drawings
Figure 10-2
Dimension drawing of CPU 1515SP PC, side view
CPU 1515SP PC (F)
132
Manual, 05/2017, A5E32701806-AC
A
Accessories/spare parts
Ordering options and accessories for CPU 1515SP PC (F)
Table A- 1
Order options for CPU 1515SP PC
Description
Article number
System version
WES7 E 32Bit 4GB RAM 1
CPU 1515SP PC, 30 GB CFast card with pre-installed S7-1500 Software
Controller CPU 1505SP
6ES7677-2AA31-0EB0
CPU 1515SP PC, 30 GB CFast card with pre-installed S7-1500 Software
Controller CPU 1505SP F
6ES7677-2FA31-0EB0
CPU 1515SP PC 4 GB, spare part (without CFast card, without software)
6ES7677-2AA40-0AA0
System version
WES7 P 64Bit 4GB RAM 1
CPU 1515SP PC, 30 GB CFast card with pre-installed S7-1500 Software
Controller CPU 1505SP
6ES7677-2AA41-0FB0
CPU 1515SP PC, 30 GB CFast card with pre-installed S7-1500 Software
Controller CPU 1505SP and WinCC Runtime Advanced as of V14
•
CPU 1515SP PC + HMI 128PT
6ES7677-2AA41-0FK0
•
CPU 1515SP PC + HMI 512PT
6ES7677-2AA41-0FL0
•
CPU 1515SP PC + HMI 2048PT
6ES7677-2AA41-0FM0
CPU 1515SP PC F, 30 GB CFast card with pre-installed S7-1500 Software
Controller CPU 1505SP
6ES7677-2FA41-0FB0
CPU 1515SP PC, 30 GB CFast card with pre-installed S7-1500 Software
Controller CPU 1505SP F and WinCC Runtime Advanced as of V14
1
•
CPU 1515SP PC F + HMI 128PT
6ES7677-2FA41-0FK0
•
CPU 1515SP PC F + HMI 512PT
6ES7677-2FA41-0FL0
•
CPU 1515SP PC F + HMI 2048PT
6ES7677-2FA41-0FM0
Windows Embedded Standard 7
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
133
Accessories/spare parts
Table A- 2
Accessories for CPU 1515SP PC (F)
Description
Article number
BusAdapter, 1 unit
•
BA 2×RJ45 (PROFINET BusAdapter with standard Ethernet socket)
6ES7193-6AR00-0AA0
•
BA 2×FC (PROFINET BusAdapter with Fast Connect Ethernet connection)
6ES7193-6AF00-0AA0
Server module; 1 unit
6ES7193-6PA00-0AA0
Strain relief for CPU 1515SP PC (F)
A5E32291462
SIMATIC IPC Service USB flash drive 8 GB (SLC), pre-installed BIOSMANAGER V3.3, Image/Partition Creator V3.3 and installation CD
6AV7672-8JD01-0AA0
SIMATIC IPC Service USB Flashdrive 16 GB, USB3.0, pre-installed BIOSMANAGER V3.3, Image/Partition Creator V3.4 and installation CD
6AV7672-8JD02-0AA0
SIMATIC IPC DiagMonitor Software V4.4
6ES7648-6CA04-4YX0
SIMATIC PC, adapter cable, DVI-I compliant with VGA, 250 mm long
6ES7648-3AB00-0XA0
Reference identification label, sheet with 16 labels, 10 units
6ES7193-6LF30-0AW0
Mounting rails, tin-plated steel strip
•
Length: 483 mm
6ES5710-8MA11
•
Length: 430 mm
6ES5710-8MA21
•
Length: 830 mm
6ES5710-8MA31
•
Length: 2000 mm
6ES5710-8MA41
SIMATIC IPC CFast cards
•
CFast 4 GB Industrial Grade
6ES7648-2BF10-0XG10
•
CFast 8 GB Industrial Grade
6ES7648-2BF10-0XH10
•
CFast 16 GB Industrial Grade
6ES7648-2BF10-0XJ10
•
CFast 30 GB Industrial Grade
6ES7648-2BF10-0XK10
Online catalog
Additional article numbers can be found on the Internet in the online catalog and online
ordering system (http://www.siemens.com/automation/mall).
CPU 1515SP PC (F)
134
Manual, 05/2017, A5E32701806-AC
B
Abbreviations
Abbreviation
Term
Meaning
AC
Alternating current
Alternating current
ALM
Automation License Manager
Tool for managing license keys in STEP 7
BIOS
Basic Input Output System
Basic Input Output System. A set of important software routines used after the startup of the CPU to load the operating
system and to provide the routines for data exchange between
hardware components.
CE
Communauté Européenne
CE label
CFast
CompactFlash ATA Serial Transfer Memory card
CoA
Certificate of Authenticity
Certificate of Authenticity, label with Microsoft Windows
"Product Key"
CoL
Certificate of License
Certificate of License for the SIMATIC software loaded
DC
Direct Current
DC current
DVD
Digital Versatile Disc
Digital storage medium with high memory capacity.
DVI-I
Digital Visual Interface
Interface for transfer of image and video data for DVI-I monitors.
ESD
Components sensitive to electrostatic charge
EN
European standard
EWF
Enhanced Write Filter
Enhanced write filter
FBWF
File Based Write Filter
File based write filter
GbE
Gigabit Ethernet
GRUB / GRUB4DOS GRand Unified Bootloader
Boot Manager
HMI
Human Machine Interface
User interface
IEC
International Electronical Commission
IM
Interface module
The interface module connects the ET 200SP distributed I/O
system with the IO controller and exchanges data with the I/O
modules via the backplane bus.
LAN
Local Area Network
Computer network that is limited to a local area.
LED
Light Emitting Diode
Light emitting diode
LLDP
Link Layer Discovery Protocol
Protocol that enables the exchange of information between
adjacent devices.
MMC
Multi Media Card
Memory card
NTFS
New Technology File System
File system that offers targeted access protection at the file
level.
NVRAM
Non-Volatile Random-Access
Memory
Non-volatile data memory that is RAM-based, the data content
of which is retained without external power supply.
PC
Personal Computer
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
135
Abbreviations
Abbreviation
Term
Meaning
PELV
Protective Extra Low Voltage
PELV, previously called "extra low voltage with safe isolation",
is a protective measure against electrical shock. See EN
50178.
PN
PROFINET
PG
Programming device
Compact programming device which meets the special requirements of industry. The PG is fully equipped for programming SIMATIC PLCs.
PS
Power supply
Power supply
PT
Power Tags
Process tags; tags enable data exchange between the components of an automation process, for example, between the
HMI device and the controller.
RAM
Random Access Memory
Main or work memory of a computer with direct access, allowing read access to data and editing.
RT
Runtime
SD
Secure Digital card
Memory card
SELV
Safety Extra Low Voltage
Safety extra-low voltage; protective measure in which circuits
with a rated voltage of up to 50 V AC or 120 V DC are operated ungrounded and feeds from circuits with a higher voltage
are separated from these by, for example, a safety transformer.
UL
Underwriters Laboratories Inc.
USB
Universal Serial Bus
Serial bus system for connecting a computer to external devices.
CPU 1515SP PC (F)
136
Manual, 05/2017, A5E32701806-AC
C
Troubleshooting
Problem
Possible cause
Remedy
CPU 1515SP PC (F) is not working.
CPU 1515SP PC (F) is not supplied Check the power supply.
with current.
CPU 1515SP PC (F) does not start.
Feedback through USB devices.
Use USB devices that comply with the
USB 2.0 specification.
Windows no longer boots.
Settings in the BIOS setup are not
correct.
Check the settings in the BIOS setup
menu Boot.
Windows clock is set incorrectly.
Time and/or date of the
CPU 1515SP PC (F) do not match.
CPU 1515SP PC (F) was not connected for more than 6 weeks.
Correct the settings in the BIOS setup
menu Main or in Windows.
USB device is not working.
USB power supply is overloaded.
Use an external power supply for the
USB device (see section Application
planning (Page 37).
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
137
Glossary
Cold restart
A startup procedure commencing when the CPU is switched on. Upon a cold restart, the
system typically performs some basic hardware checks and then loads the operating system
from the hard disk into the work memory.
Controller
Integrated hardware and software controlling the operation of a specific internal or I/O device
(e.g. keyboard controller).
Device configuration
The device configuration of a PC/programming device includes information on the features
and options of the PC/programming device such as memory configuration, drive types,
monitor, network address etc. The data is stored in a configuration file and is used by the
operating system to load the corresponding device drivers or assign device parameters.
Drivers
Program sections of the operating system. They convert data from the user programs to the
specific formats required by the I/O devices (e.g. hard disks, monitors, printers).
Enhanced Write Filter (EWF)
Configurable write filter making it possible to boot Windows Embedded Standard from writeprotected media (e.g. from CD-ROM), to write-protect individual partitions and to adapt file
system performance to the user's requirements (e.g. when using CFast cards).
Ethernet
Local network (bus structure for text and data communication with a data transmission rate
of 10/100/1000 Mbps.
File-Based Write Filter (FBWF)
Configurable write filter making it possible to write-protect individual files.
Image
An image is a copy of hard-disk partitions, for example, which is stored as backup in a file so
that it can be restored if necessary.
CPU 1515SP PC (F)
138
Manual, 05/2017, A5E32701806-AC
Glossary
Interface
● Connection between individual hardware elements such as PCs, programming device,
printer or screen by means of physical plug-in connections (cables).
● Connection between different programs to allow them to be used together.
LAN
Local Area Network: LAN refers to a local network consisting of a group of computers and
other devices which are distributed over a relatively restricted area and connected through
communication lines. The devices connected to a LAN are referred to as nodes. The
purpose of networks is the shared use of files, printers or other resources.
License key
The license key is the electronic license stamp of a license. Siemens AG provides a license
key for software that is protected by licensing laws.
Operating system
Generic term which describes all functions for controlling and monitoring user program
execution and distribution of system resources to the user programs as well as maintenance
of the operating mode in cooperation with the hardware.
Power options
The power options can be used to reduce the power consumption of the computer while still
keeping it ready for immediate use. In Windows via Start > Control Panel > Hardware and
Sound > Power Options.
Restart
The restart of the company that is already in operation using, for example, the
<Ctrl+Alt+Del> shortcut without switching off the power supply.
Restore DVD
You use the Restore DVD to reset your system partition or the entire hard disk to the delivery
state in the event of an error. The DVD contains all the image files required and is bootable.
ROM
Read Only Memory. ROM refers to a read-only memory where each memory location can be
addressed individually. The stored programs or data are hard-coded and are preserved even
in the event of a power failure.
CPU 1515SP PC (F)
Manual, 05/2017, A5E32701806-AC
139
Glossary
S.M.A.R.T
Self-Monitoring, Analysis and Reporting Technology (SMART or S.M.A.R.T.) is an industry
standard for storage media. It provides for permanent monitoring of relevant parameters and
thus early recognition of pending defects.
SATA
Serial ATA. An interface for hard disk drives and optical drives with serial data transfer.
SETUP (BIOS setup)
A program used to determine information on the device configuration. The device
configuration of the CPU 1515SP PC (F) is pre-set. Changes must be made whenever a
memory expansion, new modules or drives are to be activated.
CPU 1515SP PC (F)
140
Manual, 05/2017, A5E32701806-AC
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising