GAT SLA 300 SlimLine RFID Antenna for Entry Control

GAT SLA 300 SlimLine RFID Antenna for Entry Control
GAT SLA 300
SlimLine RFID Antenna for Entry Control
Application
The RFID antenna GAT SLA 300 is used for identification of persons
within entry control systems. The identification is made using RFID (Radio
Frequency Identification) data carriers. The evaluation and authorisation is
performed by the connected entry control terminal.
The slime shape of the GANTNER SlimLine design allows for installation
e.g. on tubular frame doors or slime structure elements.
Functional description
Oderinformation
Persons identify themselves with their own data carriers at the GAT SLA 300.
Description
The information is read and transferred via the HF interface to a control
unit in a secured area, which then makes the authorisation check and
controls the unlocking device accordingly. An entry control terminal from
GANTNER (GAT Access 6200, GAT Terminal 2500, GAT ST 210 or GAT
PartNo.
GAT SLA 300
909586
SlimLine RFID antenna, 13.56 MHz, in housing for
surface mounting
ST 260) is used as control unit.
A 2 coloured background lighting of the reader point serves as signalling
Accessories
to users. The 4-segment LED-display at the top of the housing serves as
Description
PartNo.
user guidance as well as for display of various status information. A beeper
is also integrated in the GAT SLA 300 for acoustic signal feedback.
GAT Access 6200 B
826786
Entry control terminal with LEGIC ® reader
Highlights
•Ergonomic design in GANTNER look&feel
•Slim shape excellent for mounting on door frames
•Reading and writing of 13.56 MHz RFID data carriers (depending on type
of connected terminal LEGIC® Prime, LEGIC® Advant, MIFARE® Standard,
GAT Access 6200 F
826887
Entry control terminal with MIFARE reader
®
GAT Access 6200 ISO
826988
Entry control terminal with ISO 15693 reader
HID I-Class, ISO 14443A and ISO 15693
•Clear signalling with LED bar and illuminated, round scan field
•Easy electrical installation and mounting
GAT Terminal 2500 AB
•Plug&Play installation
•Smooth and rounded design for ease of access e.g. at turnstiles to prevent
GAT Terminal 2500 AF
427581
Access control terminal with LEGIC reader
®
509481
Access control terminal with MIFARE reader
®
baggage etc. getting caught or damaged
•Mounting on metal surfaces is possible
•Suitable for outdoor use
GAT ST 210
434377
Offline access control terminal with LEGIC® reader
GAT ST 260
499590
Online access control terminal with LEGIC® reader
www.gantner.com
Valid as from April 26 th 2010 • Technical data subject to modifications without notic!
DB_GAT-SLA300_ EN _11.indd • PartNo.: 989089
1
Technical data
Nominal voltage:
12 - 24 VDC, from control unit
Frequency reader field:
13.56 MHz
Supported RFID technologies:
(depending on type of conn. terminal)
- LEGIC ® Prime/LEGIC ® Advant
- MIFARE ® Standard
- HID I-Class
- ISO 14443A
- ISO 15693
Reading distance:
Display elements/signalling
- Reader:
- Bar display:
- Akustischer Signalgeber:
Interface to control unit:
- Data (HF coaxial)
- Signal line (power supply, LEDs,
beeper)
Housing material:
Plastic
Dimensions:
44 x 139.9 x 22.2 mm
Permitted ambient temperature: -20 to +70°C
Permitted storage temperature:
-20 to +70°C
2 - 8 cm (depending on data carrier)
Protection type:
IP 54
Protection class:
III
Background lighting,
2 different colours
4 LED-segments in 3 different
colours
Beeper
Weight:
0.5 kg
Environment class
based on VDS 2110:
III (conditions in outdoor areas)
Dimensions
1
3
81,9 mm
139,9 mm
1. LED status display
2. Illuminated round scan field
3. Fastening screws (2 x)
4. Potentiometer for antenna calibration
4
2
39,0 mm
3
22,2 mm
44,0 mm
Typical application
GAT Access 6200
GAT Terminal 2500
Power supply
Network
GAT SLA 300
Door strike
2
Valid as from April 26 th 2010 • Technical data subject to modifications without notic!
DB_GAT-SLA300_ EN _11.indd • PartNo.: 989089
www.gantner.com
Mounting and installation instructions
The device back part is mounted to a flat background (e.g. concrete wall).
Mounting is also permitted on a metallic background, in which case the
internal antenna must be calibrated to adjust the reading field.
Recommended mounting height: bottom edge of device 1.3 m.
1
Mounting
3
139,9 mm
81,9 mm
8
First connect the cables according to the electrical connection scheme
7
on page 4. Connection must be made in power-less state. The cables are
flush-mounted (6). Please ensure that the cable outlet in the wall isn‘t
9
visible after mounting the GAT SLA 300. After connecting the cables press
5
5
the connection terminal cover (8) tightly onto the terminal (for protection
against dirt and humidity).
6
The device back part is fixed to the background with two screws (3). Use
proper screws and dowels according to the type of background, in order
39,0 mm
3
2
to guarantee that the GAT SLA 300 is attached securely.
4
If the GAT SLA 300 is mounted in outside area, the sealing cap (9) must
be cut-off from the terminal cover and plugged into the opening of the
potentiometer (4) for protection against dirt and humidity. If necessary first
calibrate the internal antenna with the potentiometer.
22,2 mm
44,0 mm
1. LED status display
Calibration of internal antenna
2. Illuminated round scan field
For correct adjustment of the RFID reading field the internal antenna
3. Fastening screws (2 x)
can be calibrated using the calibration potentiometer (4). Therefore first
4. Potentiometer for antenna calibration
connect the GAT SLA 300 to the terminal (see page 4). Use a non-
5. Device back part
metallic screw driver to turn the potentiometer and simultaneously use
6. Flush-mounted cable
a GAT Power Meter 1000 (PartNo.: 370010) or a data carrier to test the
7. Connection terminals
strength of the RFID reading field. Use one of the data carriers that will
8. Connection terminal cover
also be used in the entry control system later.
9. Sealing cap
Attachment of the device upper part
Removing the device upper part
After mounting and electrical connection the device upper part is clipped
If the GAT SLA 300 must be dismounted, e.g. in case of maintenance
onto the device back part as shown by the following figures.
work, the device upper part must be removed. Therefore use a flat tool
(e.g. a screw driver) to push into the slot on the bottom of the housing in
order to loosen the upper part and to carefully swing it forward.
1.
2.
1.
www.gantner.com
2.
Valid as from April 26 th 2010 • Technical data subject to modifications without notic!
DB_GAT-SLA300_ EN _11.indd • PartNo.: 989089
3
Electrical connections
Connection to GAT Access 6200
ANT -
ANT +
GAT Access 6200
BEEPER
LED GREEN
LED RED
+5 VDC
GAT SLA 300
2
1
Connection to GAT Terminal 2500
Data
HSI
HSO
Ant 2 +
GND
Ant 1 +
Beeper
LED red
GND
B
A
Sabo
Sabo
LED gr.
VOut +
B
GND
A
Lock -
Lock +
GND
ext. Reader
Host
Ethernet
Peripherie
N.O.
Shutdon VIn +
ANT -
GAT Terminal 2500
ANT +
BEEPER
LED RED
LED GREEN
+5 VDC
GAT SLA 300
SD-Card
2
1
Power supply
Connectable to the following control units
DC power supply (see technical data) from the connected control unit.
GAT Access 6200 B/F/ISO, GAT Terminal 2500 AB/AF, GAT ST 210,
GAT ST 260
Recommended cable / cable length
Signal cable (1):
shielded data line (recommendation e.g. CAT5)
Antenna cable (2): 50 Ω coax cable (recommendation RG 58 or RG 316)
Cable length depends on the control unit, max. 40 m.
Safety instructions
- This device must be installed by qualified personnel only.
- The applicable safety and accident prevention regulations
must be observed.
- Safety devices must not be removed.
- Please observe the technical data of the device specified
on the data sheet.
- The device must be disconnected from the power supply
prior to installation, assembly or dismantling.
4
Valid as from April 26 th 2010 • Technical data subject to modifications without notic!
DB_GAT-SLA300_ EN _11.indd • PartNo.: 989089
www.gantner.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising