Indendørs betjeningstastatur - KP-15/23WF

Indendørs betjeningstastatur - KP-15/23WF
Indendørs betjeningstastatur - KP-15/23WF
Et tastatur er en meget nem betjeningsløsning til dit alarmsystem, hvor du ved brug af
pinkode nemt kan til- og frakoble alarmen.
Sensor oversigt
1. Active LED
2. Status LED
3. Fault Display LED
4.
Arm Key
5.
Home Key
6. ⨿ Key
- Check Control Panel Status
7.
Disarm Key
- to move back one step
8. # Key
9. Ý Key
- Enter KP Pin Code + Ý Key to enter Test Mode
10. Emergency Alarm (if enabled)
- press both 7 and 9 to trigger emergency alarm
11. Fire Alarm (if enabled)
- press both 4 and 6 to trigger fire alarm
12. Panic Alarm (if enabled)
-press both 1 and 3 to trigger panic alarm
13. Battery Insulator
14. Mounting Hole
15. Tamper Swtich
<NOTE>
C
C
C
A short beep will sound along with key pressing to indicate that the button pressed is valid.
4 continuous beeps will sound indicating mistake and the user should repeat the process again.
Forskellen mellem 15 & 23, er at 23 er indendørs og 15 er udendørs.
l
LED Indicator
Active LED (Blue/Orange):
l
l
l
l
Blue LED on: the system is in Test Mode.
Blue LED flash: low battery in Test Mode.
Orange LED on 5 seconds: the system is in Normal Operation Mode.
l
Orange LED flashes for 5 seconds: low battery in Normal Operation Mode.
<NOTE>
C
When idle, all LED’s are off. After any key press, the Active Orange LED goes on for 5 seconds indicating that
Remote keypad is active.
Active Orange LED will turn off after successful completion of a valid keystroke sequence, or when the pause
in between key stokes is longer than 5 seconds.
When the Active Orange LED turns off before a valid keystroke sequence is completed, the previous entered
keys are ignored.
C
C
Status LED (Blue/Red):
l
Red LED on: the system is in Away Mode
Red LED flash: the system is in Home Mode.
Blue LED on: activation of Disarm Mode.
Blue LED flash: failure due to the following reasons:
Ø
No response sent by the control panel within 4 seconds.
Ø
PIN code was incorrect.
Ø
Request for Home mode during Arm mode.
Ø
Request for Force arm.
l
l
l
l
Fault LED (Orange):
l
l
l
Orange flash: system failure (panel tamper, AC fault, sensor temper, sensor out of order, open door)
l
Orange LED on: Alarm Memory(depend on Control Panel.
Programmerings mode
l
Remote keypad can be put into Test mode by entering the PIN code (default: 0000) followed by * key. The
Active Blue LED goes on along with a long beep sounding.
l
To exit Test mode, press
key twice, Remote keypad will sound a long beep and the Active LED will turn
from Blue to Orange, then Remote keypad returns to Normal Operation mode. Otherwise, Remote keypad will
automatically exit Test mode after 5 minutes and return to Normal Operation mode.
<NOTE>
C
C
The Test Mode is helpful to bypass Remote keypad Tamper alarm when installing, replacing low batteries or
removing to different mount site.
When Remote keypad is in Test mode, it operates as wake-up condition thus will NOT disconnect after 5
seconds.
Under the Test mode, the following functions can be enabled:
n
Press * key and then 7 key — to transmit Remote keypad learn signal
n
Press *key and then 2 key — to enable Dual-key Panic Alarm function
n
Press * key and then 3 key — to enable Dual-key Fire Alarm function
n
Press * key and then 4 key — to enable Dual-key Medical Alarm function
n
Press * key and then 6 key — to change the Pin Code
Enter Old Pin Code and then press ⨿ key
n
Enter New 4-digit Pin Code and then press # key.
Press * key and then 5 key — to disable all Dual Key function
n
n
Press
key twice — to leave the Test Mode.
Press * key and then 8 key — to enable Arm/ Home without PIN Code function
n
Press * key and then 9 key — to enable Arm/ Home with PIN Code function(Code checked by panel)
(Default)
Press * key and then 0 key — to enable Arm/ Home/ Disarm with KP PIN Code function (Code checked
by KP)
n
l
Installation Procedures
Step 1.
Put remote keypad in Test mode by entering KP PIN code (default: 0000), then press * key. The Active
Blue LED will turn on alone with a long beep sounding.
Step 2.
Adding remote keypad into the Control Panel:
I. Put the Control panel into Device +/- menu and select the Add Devices sub menu.
II. Press * key then 7 key when requested. Remote keypad will sound a long beep.
<NOTE>
C
If remote keypad does not sound a long beep, it means the Control Panel does not receive the
signal from remote keypad, please press * key then 7 key again.
III. Refer to the operation manual of your control Panel under the section of Device +/- to complete the
learn-in process.
IV. After Control Panel receives the signal from remote keypad, it will send an acknowledgement back to
remote keypad. The remote keypad will then beep 3 times to confirm the acknowledgement has been
received.
<IMPORTANT NOTE>
C
If remote keypad does not perform 3 beeps, please restart the learning procdeure from Step 1.
Step 3.
Step 5.
After the Remote keypad is learnt-in, put the Control Panel into Walk Test mode, hold the Remote
keypad in the desired location, and press the * key then 7 key to confirm this location is within signal
range of the Control Panel.
When you are satisfied that the Remote keypad works in the chosen location, you can proceed with
mounting the Remote keypad following the steps described below (see Mounting Remote keypad).
Setting the KP Pin Code:
I. When the keypad is under Test mode, press * key then 6 key, a long beep will be sound.
II. Enter 0000 (default PIN code)
III. Press ⨿ key, remote keypad sounds a long beep.
IV. Enter your new 4-digit code.
V. Press # key, remote keypad sounds a long beep. The new PIN code is enabled.
Step 6.
Press
Step 4.
l
key twice to leave Test mode and the installation is completed.
How to Set System Mode
You may choose to arm/home arm with or with out a Pin Code:
Arm/Home with Pin Code - In the Test mode, Pressing * key and then 9 key can enable Arm/ Home with
PIN Code function
Ø
Enter Arm Mode: Enter any one of Control Panel user code and press
Status Red LED will turn ON alone with a long beep.
key. At normal operation, the
Ø
Enter Home Mode: Enter any one of Control Panel user cods and
Status Red LED will flash 4 times alone with 3 beeps.
key. At normal operation, the
Ø
Return to Disarm Mode: Enter any one of Control Panel user code and
key. The Status Blue LED will
turn ON along with 2 beeps.
Arm/Home without PIN Code - In the Test mode, Pressing * key and then 8 key can enable Arm/ Home
without PIN Code function
Ø
Enter Arm Mode: Press
key. The Status Red LED will turn ON alone with one long beep.
Ø
Enter Home Mode: Press
Ø
Return to Disarm Mode: Enter any one of Control Panel user code and
will turn ON along with 2 beeps.
key. The Status Red LED will flash 4 times alone with 3 beeps.
Key. The Status Blue LED
Arm/Home with KP Pin Code - In the Test mode, Pressing * key and then 0 key can enable Arm/ Home with
KP PIN Code function
Ø
Enter Arm Mode: Enter KP Pin code+
with a
long beep.
key. At normal operation, the Status Red LED will turn ON alone
Ø
Enter Home Mode: Enter KP Pin code+
key. At normal operation, the Status Red LED will flash 4
times alone with 3 beeps.
Ø
Return to Disarm Mode: Enter KP Pin code+
beeps.
key. The Status Blue LED will turn ON along with 2
Få meget mere ud af din TrueGuard alarm.
FACEBOOK : Her kan du følge os og få løbende tips og tricks på facebook :
https://www.facebook.com/TrueGuardAlarm/
YOUTUBE : Se også installations videoer og andre videoer på YouTube. Klik her:
https://www.youtube.com/channel/UCpHlY29gQAxOTsEeGAFHQew
NYHEDSBREV : Hold dig opdateret med nyheder og nyt tilbehør til din alarm. Tilmeld dig
nyhedsbrevet på www.TrueGuard.dk
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising