ve8022a/ve8022ar dual enhanced network trunk port

ve8022a/ve8022ar dual enhanced network trunk port
Issue 2
VE8022A/VE8022AR
DUAL ENHANCED NETWORK TRUNK PORT
INTRODUCTION
The VE8022A/VE8022AR Dual Enhanced Network
Trunk Port allows most loop start station ports to
be connected to a managed IP-based LAN/WAN.
SIP connectivity allows the VE8022A/VE8022AR to
act as a gateway device between a SIP telephone
system and the loop start Valcom paging systems.
The VE8022A is designed for wall or table
placement. The VE8022AR is designed for 19”
rack mounting (1U).
VE8022A
SPECIFICATIONS
VE8022AR
Access Methods
 PBX, FXS Port
 SIP
Nominal Power Requirements
Features








RJ-45 for network connection
2 RJ-11 FXO connections
2 RJ-11 failover telephone connections
Decode Caller ID signals
Front panel activity LED
Network activity LEDs
2.5mm jack for optional DC power
Power over Ethernet (PoE) 802.3af compatible
Dimensions/Weight (VE8022A)
 1.38 H x 6.13" W x 5.25" D
(3.50cm H x 15.6cm W x 13.33cm D)
 Weight: 1.25 lbs. (0.57 kg)
Dimensions/Weight (VE8022AR)



1 Standard 19” Rack Unit
1.75 H x 16.50" W x 5.25" D
(4.45cm H x 41.91cm W x 13.33cm D)
Weight: 5.10 lbs. (2.32 kg)
Nominal Specifications
Input Impedance:
Input Level:
Output Impedance:
Output Level:
600 Ohms
-10dBm
600 Ohms
- 10dBm nominal
1
Via back panel barrel connector:
Voltage:
Current:
Via 802.3af PoE Ethernet Switch:
802.3af:
24VDC
325mA
Class 3
Environment
Temperature:
Humidity:
0 to +40° C
0 to 85% non-precipitating
INSTALLATION
NOTE: The telephone system referred to in this
manual is the customer premise equipment
such as an electronic key system, a PBX or a
dedicated single line telephone sets. The
VE8022A/VE8022AR is not intended for direct
or indirect connection to the public telephone
network. When used with a customer premise
telephone system such as a key system or PBX
system, these units are interfaced to the
system via a fully protected page port or
system central office port, which is a fully
protected interface device. Also, the host
system must be configured to disallow central
office trunk conferencing in order to prevent
indirect connection to the public network.
947497
Precautionary Designations
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
`
CAUTION: To reduce the risk of electric shock,
Do not remove cover.
No user serviceable parts inside.
Refer servicing to qualified service personnel.
This symbol indicates that dangerous
voltage constituting a risk of electric
shock is present within this unit.
This symbol indicates that there are
important operating and maintenance
instructions in the literature accompanying
this unit.
Figure 1. Mounting
FCC Information
Power Connections
This equipment has been tested and found to
comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference when the equipment is operated in
a commercial environment. This equipment
generates, uses and can radiate radio
frequency energy and if not installed and used
in accordance with the instruction manual, may
cause harmful interference to radio
communications. Operation of this equipment
in a residential area may cause harmful
interference in which case the user will be
required to correct the interference at his own
expense.
The preferred method of powering a
VE8022A/VE8022AR is via a Power over Ethernet
(PoE) switch meeting the 802.3af specification.
Mounting
The VE8022A is designed for wall or table
mounting. The VE8022AR is designed for 19” rack
mounting (1U).
Table: Provided with the VE8022A are four rubber
pads. Peel pads off their carrier backing and place
at the four corners of the bottom of the unit.
Wall: Secure mounting brackets to the VE8022A,
then secure the VE8022A to the wall.
If the rear panel barrel connector is used for power,
the preferred power supply is a Valcom VIP-324D.
Make all required signal connections before
applying power to the unit. If powering via 802.3af,
make sure all signal connections via the back
panel are made then connect the
VE8022A/VE8022AR to the Ethernet switch.
If power is supplied via the barrel connector, make
sure all signal connections are secure. Attach the
unit to the network via the front panel RJ-45
Ethernet connector. Apply power by plugging the
power supply into the VE8022A/VE8022AR 2 via
the barrel connector on the rear of the
VE8022A/VE8022AR.
Network Connection
The VE8022A/VE8022AR has one RJ-45 network
connector on the front panel.
Use the supplied patch cable to connect the
VE8022A/VE8022AR to an Ethernet switch.
Rack: Secure mounting brackets to the
VE8022AR. See Figure 1. Place the VE8022AR
into a standard 19” rack and secure with proper
hardware (not included).
2
947497
Signal Connections
Status Indicator Lights
FXS Connection: Connect standard analog FXS
circuits, capable of providing calling party
disconnect, to the VE8022A/VE8022AR via the
rear panel RJ-11 jacks labeled Port 1 Line or Port
2 Line. Tip and Ring appear on pins 3 and 4 of
these jacks.
The VE8022A/VE8022AR has 3 status indication
lights on the front panel:
Failover Telephone Connections:
Connect standard analog telephones to the
VE8022A/VE8022AR via the rear panel RJ-11
jacks labeled Port 1 Phone or Port 2 Phone. Tip
and Ring appear on pins 3 and 4 of these jacks.
STATUS: Flashes during normal operation and
solid during system startup.
LINK: Indicates 100 Mbit Ethernet connection
when illuminated. No activity indicates 10 Mbit
connection.
ACT: Indicator flashes to indicate network activity.
TECHNICAL ASSISTANCE
When trouble is reported, verify power is being
supplied to the unit and there are no broken
connections. Check voltages for proper polarity to
the one-way amplified speakers. If a spare unit is
available, substitute a spare unit for the suspected
defective unit.
Rear View: VE8022A
Assistance in troubleshooting is available from the
factory. Call (877) 427-2166 and ask for Valcom
Engineered Solutions Technical Support, or visit
our website at www.ValcomES.com.
Rear View: VE8022AR
Setup
Information specific to your application will need to
be programmed into the VE8022A/VE8022AR
using a computer. The PC used for programming
should be connected to the same subnet as the
VE8022A/VE8022AR. Setup will be done using
the IP Solutions Setup Tool. Download the latest
version of the free IP Solution Setup Tool from
Valcom website at www.valcom.com/vipsetuptool.
Valcom equipment is not field repairable. Valcom,
Inc. maintains service facilities in Roanoke, VA.
Should repairs be necessary, attach a tag to the
unit clearly stating your company name, address,
phone number, contact person and the nature of
the problem. Send the unit to:
Valcom, Inc.
Repair & Return Dept.
5614 Hollins Road
Roanoke, Va. 24019-5056
VALCOM LIMITED WARRANTY
Valcom, Inc. warrants its products only to the original purchaser, for its own use, to be free from defects in materials and workmanship under conditions of
normal use and service for a period of one year from the date of shipment. This Limited Warranty obligation shall be limited to the replacement, repair or refund
of any such defective device within the warranty period, provided that:
1. inspection by Valcom, Inc. indicates the validity of the claim;
2. the defect is not the result of damage, misuse or negligence after the original shipment;
3. the product has not been altered in any way or repaired by others and that factory sealed units are unopened (a service charge plus parts
and labor will be applied to units defaced or physically damaged);
4. freight charges for the return of products to Valcom are prepaid;
5. all units 'out of warranty' are subject to a service charge. The service charge will cover minor repairs (major repairs will be subject to
additional charges for parts and labor).
This Limited Warranty is in lieu of and excludes all other warranties, expressed or implied and in no event shall Valcom, Inc. be liable for any
anticipated profits, consequential damages, loss of time or other losses incurred by the buyer in connection with the purchase, operation,
maintenance, installation, removal or use of the product. The maximum liability of Valcom under this warranty is limited to the purchase price of the
specific Product covered by the warranty.
Disclaimer. Except for the Limited Warranty provided herein, the product is provided “as-is” without any warranty of any kind whatsoever including, without
limitation, any WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT.
This warranty specifically excludes damage incurred in shipment. In the event a product is received in damaged condition, the carrier should be notified
immediately. Claims for such damage should be filed with the carrier involved in accordance with the F.O.B. point.
Headquarters:
Valcom, Inc.
5614 Hollins Road Roanoke, VA 24019-5056
Phone: (540) 563-2000 FAX: (540) 362-9800
3
947497
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising