42898 Card Reader UK Stock compressed
USB 2.0 7 in 1
Card Reader Panel
User Manual
English
LINDY No. 42898
www.LINDY.com
© LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - SECOND EDITION (Dec 2004)
Driver Installation
Users of Windows XP/ME/2000(SP3) DO NOT need to install drivers. Windows will automatically provide a USB
2.0 device driver for the 7-in-1 card reader.
Win 98SE/2000 users need to install the driver using the supplied CD. Insert the CD and follow the on screen
instructions.
Hardware Installation
Step 1
Connect the supplied cables to the connectors in the card
reader assembly. The mini-USB connector plugs into the
connector on the card reader circuit board and the FireWire
and Type A USB extension cables install onto the connector
pins on the USB/FireWire Extension circuit board.
The USB cables attach to the motherboard and card reader
using the coloured wires identified in the table below –
Colour
Signal
Red
VCC
White
DATA -
Green
DATA +
Black
GND
The diagram to the right, illustrates the pin layout of the
USB and FireWire connectors on the USB/FireWire
Extension Port circuit board.
CAUTION: To avoid damaging the card reader you
must ensure the VCC, DATA+, DATA- and GND wires
connect to the correct pins.
Step 2
Install the card reader assembly into a spare 5¼“ bay
in your computer.
Step 3
Secure the card reader using the supplied screws.
Step 4
Connect the USB cables from the Card Reader/USB Extension port to the motherboard and/or add-on card.
The four pin connectors from the card reader and USB
extension ports install onto the motherboard using the wires
identified in the table –
Colour
Signal
Red
VCC
White
DATA -
Green
DATA +
Black
GND
CAUTION: Be sure to attach the VCC, DATA+, DATA- and GND wires to the correct pins on your
motherboard, otherwise damage may occur! (Check your motherboard or system manual to identify the
correct connections)
Step 5
Connect the Type A USB Male connector from the USB
Extension port to a spare USB Female socket on your
motherboard or add-on card.
If no internal connection is available you can route the USB cable
through the back of the computer to an external port.
Step 6
Connect the FireWire connector to a port on your motherboard or
add-on card
If no internal connection is available you can route the FireWire
cable through the back of the computer to an external port.
Installation is now complete!
Radio Frequency Energy
Shielded cables must be used with this equipment to maintain compliance
with radio frequency energy emission regulations and ensure a suitably
high level of immunity to electromagnetic disturbances.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B Digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
 Reorient or relocate the receiving antenna
 Increase the separation between the equipment and receiver
 Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
 Consult the dealer or an experienced radio/TV technician for help
You are cautioned that changes or modifications not expressly approved by the party
responsible for compliance could void your authority to operate the equipment.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired
operation
For Home and Office Use
Tested to comply
with FCC Standards
LINDY No. 42898
© LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - SECOND EDITION (Dec 2004)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising