rack mount - Silver Peak
Quick Start Guide
NOTES:
•
Begin installing the rails in the alotted space that is closest to the
bottom of the rack enclosure.
•
The illustrations in this document do not represent a specific system.
A
Identifying the rail kit contents
• Supplement •
Installing and removing tool-less rails
B (square
hole or round hole racks)
C
Installing and removing tooled rails
(threaded hole racks)
3
RACK MOUNT
INSTRUCTIONS
• 1-RU WITH RAILS •
NX-2700
Locate the components for installing the rail kit assembly:
•
Two A7 ReadyRails II sliding rail assemblies (1)
•
Two hook and loop straps (2)
2
2
NX-3700
1
4
NX-5700
NX-6700
1
1
NX-7700
4
3
Before You Begin
‰‰ Check your packing slip to
verify that you have all the
necessary items.
1. Position the left and right rail end pieces labeled FRONT facing
inward and orient each end piece to seat in the holes on the front
side of the vertical rack flanges (1).
‰‰ Make sure you have a standard
Phillips screwdriver.You may
also need a flat-tipped screwdriver.
2. Align each end piece in the bottom and top holes of the desired U
spaces (2).
2
4. Repeat these steps to position and seat the front end piece on the
vertical rack flange (3).
PN 200715-001 Rev E
© 2014 Silver Peak Systems, Inc.
3. Engage the back end of the rail until it fully seats on the vertical rack
flange and the latch clicks into place.
1. Remove the pins from the front and rear mounting brackets using a
flat-tipped screwdriver (1).
2. Pull and rotate the rail latch subassemblies to remove them from the
mounting brackets (2).
3. Attach the left and right mounting rails to the front vertical rack
flanges using two pairs of screws (3).
4. Slide the left and right back brackets forward against the rear vertical
rack flanges and attach them using two pairs of screws (4).
5. To remove the rails, pull the latch release button on the end piece
midpoint and unseat each rail (4).
Silver Peak Systems, Inc.
2860 De La Cruz Boulevard
Suite 100
Santa Clara, CA 95050
1.877.210.7325 (toll-free in USA)
+1.408.935.1850
www.silver-peak.com/support
Page 1 of 3
Quick Start Guide
D
E
Installing the system in a rack
• Supplement •
2
3
F
Removing the system from the rack
Engaging and releasing the slam latch
3
1
RACK MOUNT
1
INSTRUCTIONS
• 1-RU WITH RAILS •
4
2
NX-2700
NX-3700
NX-5700
2
NX-6700
3
NX-7700
1
1
1. Pull the inner slide rails out of the rack until they lock into place (1).
1. Locate the lock levers on the sides of the inner rails (1).
2. Locate the rear rail standoff on each side of the system and lower
them into the rear J-slots on the slide assemblies (2).
2. Unlock each lever by rotating it up to its release position (2).
3. Rotate the system downward until all the rail standoffs are seated in
the J-slots (3).
4. Push the system inward until the lock levers click into place.
3. Grasp the sides of the system firmly and pull it forward until the rail
standoffs are at the front of the J-slots.
4. Lift the system up and away from the rack and place it on a level
surface (3).
1. Facing the front, locate the slam latch on either side of the system
(1).
2. The latches engage automatically as the system is pushed into the
rack and are released by pulling up on the latches (2).
3. To secure the system for shipment in the rack or for other unstable
environments, locate the hard-mount screw under each latch and
tighten each screw with a #2 Phillips screwdriver (3).
5. Press the slide-release lock buttons on both rails and slide the
system into the rack (4).
PN 200715-001 Rev E
© 2014 Silver Peak Systems, Inc.
2
Silver Peak Systems, Inc.
2860 De La Cruz Boulevard
Suite 100
Santa Clara, CA 95050
1.877.210.7325 (toll-free in USA)
+1.408.935.1850
www.silver-peak.com/support
Page 2 of 3
Quick Start Guide
G
Routing the cables
• Supplement •
1
RACK MOUNT
INSTRUCTIONS
• 1-RU WITH RAILS •
3
NX-2700
NX-3700
NX-5700
NX-6700
NX-7700
2
NOTE: Use the two hook and loop straps provided in the rail kit to
route the cables at the back of your system.
1. Locate the outer CMA brackets on the interior sides of both rack
flanges (1).
2. Bundle the cables gently, pulling them clear of the system connectors
to the left and right sides (2).
© 2014 Silver Peak Systems, Inc.
PN 200715-001 Rev E
3. Thread the hook and loop straps through the tooled slots on the
outer CMA brackets on each side of the system to secure the cable
bundles (3).
Silver Peak Systems, Inc.
2860 De La Cruz Boulevard
Suite 100
Santa Clara, CA 95050
1.877.210.7325 (toll-free in USA)
+1.408.935.1850
www.silver-peak.com/support
Page 3 of 3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising