Sem título-1 - TuningHiFiShop
LEDS INDICATORS (TOP OF THE AMPLIFIER)
- BLUE LED (POWER)
lights when the power
is on.
- RED LED (PROT) illuminates only when
there is a problem in the functioning of
the device.
- RED LED (CLIP) flashes when
the amplifier output begin to
distort the sound.
SYSTEM TROUBLESHOOTING
If some problem occurs, the amplifier will shut down and the RED LED will flash alternately with the BLUE LED. As
the problem occurred, the BLUE LED will blink a certain number of times. So we have a diagnosis according to the
table below:
DIGITAL LINE
USER’S GUIDE
Note: If only the RED LED blinks (BLUE LED OFF), turn on the device with the volume of CD/MP3-player down. If
the problem persists, please contact us.
WHAT TO DO IN CASE OF PROBLEMS
NOT TURN ON:
- The cables are not properly connected (terminals +BATT, GND and REM). Make sure that all
connections are mechanical and electrical contact.
- Fuses / breakers (external) are defective or burned. Pay attention to the correct value of the new fuse!
NO SOUND:
- The cables of the speakers or RCA plugs are not connected correctly.
- Check that the LEVEL control is not in the minimum.
NO SOUND/PROTECTION RED LED FLASHING:
- See diagnosis UP (SYSTEM TROUBLESHOOTING).
- The speakers or cables defectives thus check the speakers, cables and connections.
POOR SOUND QUALITY (DISTORTION):
- The speakers are overloaded, therefore decrease the level and redo the gain setting (See item 2 /
OVERVIEW).
WEAK BASS:
- Cables speakers (+) and (-) are reversed, speaker out of phase (see Section 7 / overview).
MOTOR NOISE, HORN, SIGNAL LIGHT, ETC:
- Use suppressive cables in ignition candles.
- Use capacitors in the alternator, horn and ignition.
- Pass the RCA cable away from any other cable, because it is more sensitive to interference.
- Connect to power (+12 V) to separate the sound system. Use a fuse to 30 cm from the battery for
protection.
- Make a good grounding of the amplifier. To do this removes the paint from the chassis of the vehicle at
the desired point. Screw the cable using a ground terminal. To protect from oxidation, insulate with
paint.
- Do not loop the ground wire. Avoid using several ground wires. Prefer a star connection, with all the
ground wires aside from a single point.
www.stetsom.com.br - export@stetsom.com
HALF
BRIDGE
SPECIFICATIONS
MODEL:
Channels:
Power @ 13.8V Mono 1 Ohm:
Power @ 13.8V Mono 2 Ohms:
Power @ 13.8V Mono 4 Ohms:
Power @ 12.6V Mono 1 Ohm:
Power @ 12.6V Mono 2 Ohms:
Power @ 12.6V Mono 4 Ohms:
Minimum Work Impedance:
Minimum Input Sensitivity:
Total Harmonic Distortion:
Signal to Noise:
Freq. Response (-3dB) @ 8 Ohms:
Crossover LOW PASS:
Subsonic Filter:
Bass Boost:
Work Voltage:
Consumption Music Signal (12,6 V):
Consumption BASS Signal (12,6 V):
Dimentions mm (A x L x C):
Weight:
1K6 ES – 2 OHMS
1
1780 Watts RMS
1030 Watts RMS
1600 Watts RMS
830 Watts RMS
2 Ohms
0,2V
< 0,9 % THD
> 90 dB
10 Hz to 10 KHz
50 Hz to 10 KHz
10 Hz to 80 Hz
0 to +12dB @ 45 Hz
9,5 to 15 V
1,7A to 77 A
1,7A to 155 A
75 x 310 x 170
2,2
1K6 ES – 1 OHM
1
1720 Watts RMS
1035 Watts RMS
1600 Watts RMS
820 Watts RMS
1 Ohm
0,2V
< 0,9 % THD
> 90 dB
10 Hz to 10 Khz
50 Hz to 10 Khz
10 Hz to 80 Hz
0 to +12dB @ 45Hz
9,5 to 15 V
1,7A to 77 A
1,7A to 154 A
75 x 310 x 170
2,2
MAR/10
OVERVIEW
INSTALLATION OF POWER (BATTERY)
AUDIO INPUT, CONTROLS AND OUTPUT AUDIO AMPLIFIED.
R
L
BASS
BOOST
10Hz / 80Hz 50Hz/10KHz 0dB/+12dB
4
5
6
For the installation of power, choose cables with
21mm ². The positive cable should come straight from
the battery with a fuse or circuit breaker protection
located 30cm from the battery. The negative cable
should have the same circumference of the positive,
and screwed into the chassis of the vehicle, taking
care to avoid paint and rust that may prevent the
passage of electric current, causing power loss and
noise in the sound.
7
INPUT VENTILATION AND POWER.
REMOTE TURN ON
* FUSE BREAKER
MÁX
30 cm
*FUSE BREAKER
70 A
ATTENTION: USE OF EXTERNAL FUSE OR BREAKER
AMPLIFIER HAS NO INTERNAL FUSE.
10
1)
11
INPUT - INPUT RCA L and R: This entry should receive the signal by RCA cable that must be
connected to the output RCA of CD/MP3-Player.
2) LEVEL - GAIN CONTROL: Controls the level of the input signal, allowing a proper adjustment to any
CD/MP3-Player of the market. For practical purposes may be adjusted as follows:
a) CD/MP3-Player, put a musical signal and adjust the volume in 80% of maximum. For example, if the
maximum volume of CD/MP3-player is 45 (100%), adjusting for 36 (80%).
b) In the amplifier, from the LEVEL at least, increase gradually until the clipping LED flashes.
c) Return the LEVEL slowly until the LED delete completely.
3) SUB SONIC FILTER: Provides a cut in the low frequency sound (subsonic). This filter is very useful
when using speakers model woofers. In these cases, the woofers are not able to reproduce the subsonic
and may even damage depending on the power and music used. Its adjustment varies from 10Hz to
80Hz.
4) LOW PASS FILTER: This control varies frequency cut filter 50 Hz to 10KHz. This filter allows passing
only the sounds below the cut off frequency.
5) BASS BOOST: Reinforces the level of bass at low frequencies 25Hz to 110Hz. From 0 to +12 dB
centered at 45Hz.
6) VENTILATION OUTPUT: allows the output of heated air from the amplifier.
7) SPEAKERS OUTPUT: This output is MONO. Beware of the polarity of the connections with the speakers
and check the minimum impedance allowed in this output. Use cables of at least 8 mm2.
8) COOLER: Cools the internal components of the amplifier. The air enter in the cooler and exits through
the exhaust ventilation (item 6).
9) + BATT: Connect the terminal (+ BATT) to the positive pole of the battery (+12 V) with a cable of at
least 21.0 mm². It is extremely important that you use a fuse or circuit breaker to protect this cable to a
maximum distance of 30 cm from the battery.
10) REM - DRIVE REMOTE: Connect the REM terminal to output for remote / antenna electric of CD/MP3Player. So when you turn on your CD/MP3-Player, the amplifier automatically turns on. A cable of 0.5
mm² is sufficient.
11) GND - GROUND CONNECTION: Use cable with 21.0 mm². Plug the cable into the chassis of the
vehicle.
NOTE: Always connect the cable GND (-) of CD-Player, or other devices at the same point.
Battery
12V
BECAUSE THE
INSTALLATION OF OUTPUT SPEAKER
The cables of the speakers should be polarized (marked) to facilitate the identification of positive and
negative. The circumference should be at least 8mm². Keep the cables from the speakers properly
insulated. Beware of metal parts that can damage the insulation of cables.
INSTALLATION WITH 2 SPEAKERS
INSTALLATION WITH 1 SPEAKER DUAL COIL
INSTALATION WITH 2 WOOFERS AND 2 DRIVERS
AMPLIFIER IS FOR A SUBWOOFER, WOOFER, DRIVER
AND ALL SPEAKER THAT RESPONSE UNTIL 10KHZ.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising