ASK[EM] Format Proximity Card Reader

ASK[EM] Format Proximity Card Reader
User’s Manual
ASK[EM] Format
Proximity Card Reader
Table of Contents
1. Important Safety Instructions..............................................................3
2. General ..................................................................................................3
3. Features.................................................................................................4
4. Identifying Supplied Parts ...................................................................4
5. Specification .........................................................................................4
6. Check Points and Tip ...........................................................................5
7. Installation.............................................................................................6
8. Wire Color Table of the Reader ...........................................................7
9. Wire Connection to Controller ............................................................7
10. Operation.............................................................................................8
11. FCC Registration Information............................................................9
12. Warranty and Service.......................................................................10
2
1. Important Safety Instructions
When using your Single Door Controller, basic safety precautions should always be followed to
reduce the risk of fire, electrical shock, and injury to persons. In addition, the following should also
be followed:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. If necessary,
use mild soap.
4. Do not use this product near water, such as bath-tub, wash bowl, kitchen sink, laundry tub, in a
wet basement, or swimming pool.
5. This product should be operated only from the type of power source indicated on the marking
label. If you are not sure of the type of power supplied to your installation site, consult your
dealer or local power company.
6. Never push objects of any kind into this product or through the cabinet slots as they may touch
voltage points or short out parts that could result in fire or electric shock. Never spill liquid of
any kind on the product.
7. To reduce the risk of electric shock, do not disassemble this product by yourself, but take it to
qualified service whenever service or repair is required. Opening or removing the covers may
expose you to dangerous voltages or other risks. Also, incorrect reassembly can cause electric
shock when the unit is subsequently used.
8. Unplug this product from the Direct Current (DC) power source and refer to qualified service
personnel under these conditions:
a. When the power supply cord or plug is damaged or frayed.
b. If liquid has been spilled on the product.
c. If the product does not operate normally after following the operating instructions in this
manual. Adjust only those controls that are covered by the operating instructions in this
manual. Improper adjustment of other controls that are not covered by this manual may
damage the unit and will often require extensive work by a qualified technician to restore
normal operation.
d. If the product exhibits a distinct change in performance.
2. General
The iPASS IP10/20 Reader is an elegant looking reader which can be mounted to metal door
frame (mullion) or any flat wall surface. The iPASS IP10/20 Reader uses an electronic module in
epoxy potting that ensures successful operation even in harsh environments.
Two-color LED (green and red) and built-in beeper sound provides accurate and reliable system
operations. There are two output formats of 26bit Wiegand output and ABA Track II Magstripe
output available and the user can select the output format as they want.
3
3. Features
- 125KHz Proximity Card Reader
- ASK [EM] Format
- Read Range: Up to 4inch (10cm)
- User Format Available
- 26bit Wiegand (Default), ABA Track II and RS232 (Optional) Output Format
- Dual Reading Technology Reader (Active and Passive Cards)
- Easy to Install on Metal Door Frame or Mullion (IP10) and Wall Mount (IP20) Suitable
- External LED Control and External Buzzer Control
- Solid Epoxy Potted
- Waterproof (IP65 / IP66)
- Reverse Polarity Protection
- Options:
Supervisory Signal
4. Identifying Supplied Parts
Please unpack and check the contents of the box.
Reader Module
(1ea)
iPASS IP10 / IP20 Bezel
(1ea)
User’s Manual
(1copy)
5. Specification
Model
Read Range
Reading Time (Card)
Power / Current
Input Port
Output Format
LED Indicator
Beeper
Operating
Temperature
Operating Humidity
Color / Material
Dimension
IP10
IP20
IPK50: Up to 2 inch (5cm)
IPC170 / IPC180: Up to 4 inch (10cm)
30ms
DC 12V / Max.150mA
2ea (External LED Control, External Buzzer Control)
26bit Wiegand (Default), RS232 and ABA Track II (Optional)
2 Color LED (Red and Green)
Piezo Buzzer
-35° to +65°C ( -31° to +149°F )
10% to 90% relative humidity non-condensing
Dark Pearl Gray / Polycarbonate
46mm x 122mm x 23mm
76mm x 124mm x 23.5mm
4
(W x H x T)
Weight
Warranty
Index of Protection
Certification
(1.82” x 4.81” x 0.87”)
160g (0.35lbs)
(3” x 4.89” x 0.87”)
185g (0.41lbs)
Life time
IP65 / IP66
UL, FCC, CE, MIC
6. Check Points and Tip
z Recommended cable type and permissible length of cable
Description
Cable Specification
Maximum
Distance
Reader (Power and Data)
Reader -> ACU
Belden #9512, 22 AWG
4 conductor, shielded
Belden #9514, 22 AWG
8 conductor, shielded
150m
* Need thicker wire if you connect the reader with high current consumption.
z Reader connection
If you install the reader in a long distance between the ACU and the reader, you have to
remind that there will be a voltage drop between both ends of GND wire. For example, if
you connect a reader with 100mA current consumption at 100m distance (assume to using
DC resistance of cable of 100Ω/100m) and the reader power is supplied from the ACU, the
voltage drop of the GND wire will be 1V. In this case, the Wiegand data signal can not be
measured lower than 1V.
The most of ACU is capturing the signal by the voltage level of data input and 1V is the
critical point whether the ACU read the data logic “1” or logic “0” therefore the reader
output can not be read correctly from the ACU.
You have to think about how you reduce the voltage drop between both ends of GND wire.
There will be two methods to reduce the voltage drop and ACU can read data correctly.
„ Reduce the DC resistance of GND wire; Using thick cable or add more wires to GND
wire in parallel. If you connect 4 wires in parallel for GND, the DC resistance of GND
wire will be reduced to 1/4 of single wire.
„ Use separate power for the reader; Disconnect +12V wire from the ACU and
connect external power supply to the reader nearby then there will be no current flow
through the GND wire and no voltage drop between both ends of GND wire.
Shield
< Reader connection using additional wires >
5
Shield
< Reader connection using external power supply >
7. Installation
7-1. Mullion/Wall Mount
Drill two 6-32 or M3 holes 3.3"(8.38cm) apart in vertical and drill one 1/2" hole for the reader
cable 1.7"(4.31cm) apart from the top hole.
(Skip this step, if you have installed an electric gang box.)
7-2. Put reader cable into the center hole and install the reader module by using two 6-32 or M3
screws (Not included).
7-3. Put bezel on to the reader module. Then push bezel until you hear the locking sound.
7-4. To detach the bezel, hold both sides of the bezel, push the bezel to the bottom, and pull the
bezel forward.
6
8. Wire Color Table of the Reader
SIGNAL
COLOR
Main Power (+12V)
Red
Power Ground (GND)
Black
Wiegand/ABA Track II Out Select In
Brown
ABA Track II CP Out
Orange
Wiegand Data 0 Out /
Green
ABA Track II Data Out
Wiegand Data 1 Out /
White
ABA Track II Clock Out
Buzzer Control In
Blue
LED Control In
Yellow
* Please cut out tail connector before installation.
9. Wire Connection to Controller
Access Controller
Main Power (+12V)
Power Ground (GND)
Wiegand / ABA Track II Out Select In
ABA Track II CP Out
Wiegand Data 0 Out /
ABA Track II Data Out
Wiegand Data1 Out /
ABA Track II Clock Out
Buzzer Control In
LED Control In
Red
Black
Brown
Orange
Green
White
Blue
Yellow
7
10. Operation
10-1. Once the power is applied, three beeping sounds can be heard and the LED toggles
the color to red-green-red indicating that the reader is in standby mode after a successful
initialization and diagnostics
10-2. Present proximity card to the reader until you hear a beep sound. The LED is
changing the color to Green simultaneously and sends the RF card data to the controller.
Afterwards the LED changes the color to red again for the next reading.
10-3. LED Control:
To change the LED colors, you may connect the LED Control Input (Yellow wire)
to power ground. The green LED is indicating that the reader is in standby mode.
Present proximity card. The LED changes the color to red simultaneously, then to green again
for the next reading.
10-4. Buzzer Control:
When the reader reads the proximity card, one beep sound generates in normal
operation mode, but you can generate more beep sounds to distinguish whether the access is
granted or denied.
To generate more beeps, you may control the Buzzer Control Input (Blue wire) to power
ground.
Afterwards you can turn the beeper on, while holding the Buzzer Control Input to power
ground.
10-5. Wiegand/ABA Track II Output Format Select:
When you remain open circuit of Wiegand/ABA select input (Brown wire) then the reader will
generate 26bit Wiegand output. When you want ABA Track II Magstripe output then connect
Wiegand/ABA select input (Brown wire) to system ground level (connect this wire to Black
wire) then the reader will generate ABA Track II output. After you select output format,
preferred output format will be selected after the power on reset. Both 26bit Wiegand and ABA
Track II Magstripe outputs are all pulled up to +5V DC by 1K ohm pull-up resistors.
8
11. FCC Registration Information
FCC REQUIREMENTS PART 15
Caution: Any changes or modifications in construction of this device which are not expressly
approved by the responsible for compliance could void the user's authority to operate
the equipment.
NOTE: This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;
1. This device may not cause harmful interface, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class A Digital
Device, pursuant to Part 15 of the FCC Rules. These limits are designed to this equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the radio or television off and on, the user is encouraged to try to correct
interference by one or more of the following measures.
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on another circuit.
4. Consult the dealer or an experienced radio/TV technician for help.
9
12. Warranty and Service
The following warranty and service information applies only to the United States of America and
Republic of Korea. For the information in other countries, please contact your local distributor.
To obtain in or out of warranty service, please prepay shipment and return the unit to the
service
facility listed below.
Headquarters: IDTECK Co., Ltd.
5F Ace Techno Tower B/D,
684-1 Deungchon-Dong, Gangseo-Gu,
SEOUL, KOREA 157-030
Tel:
+82-2-2659-0055
Fax:
+82-2-2659-0086
E-mail: webmaster@idteck.com
Website: www.idteck.com
U.S Branch: RF Logics Inc.
370 Amapola Ave, #106
Torrance, CA 90501
Tel: 310-782-8383
Fax: 310-782-8298
E-mail: rflogics@rflogics.com
Website: www.rflogics.com
Hong Kong Branch: IDTECK Hong Kong
12/F, B2B Centre, No.36 Connaught Road West, Hong Kong
Tel: 852-2581-9580
Fax: 852-2234-5150
E-mail: alchu@qala.com.hk
Website: www.ristarhk.com
Please use the original container, or pack the unit(s) in a sturdy carton with sufficient packing to
prevent damage and include the following information:
1. A proof-of-purchase indicating model number and date of purchase.
2. Bill-to Address.
3. Ship-to Address.
4. Number and description of units shipped.
5. Name and telephone number of person to be contacted.
6. Reason for return and description of the problem (Should be as detailed as possible!)
NOTE: Damage occurring during shipment is deemed the responsibility of the carrier, and
claims should be made directly to the carrier.
10
MEMO
11
The specification contained in this manual are subject to change without notice at any time.
5F, Ace Techno Tower B/D, 684-1, Deungchon-Dong,
Gangseo-Gu, Seoul, 157-030, Korea
Tel : +82-2-2659-0055
Fax : +82-2-2659-0086
E-mail : webmaster@idteck.com
MARIPASHE2X
May. 2006 Copyright ©2006 IDTECK Co., Ltd.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising