furniture laboratory furniture

furniture laboratory furniture
LABORATORY
FURNITURE
FURNITURE
WOOD CASEWORK
INTRODUCTION - CASEWORK CONSTRUCTION DETAILS AND SPECIFICATIONS
Overview
Doors and Drawers
Solid doors and drawers are 3/4” particle board.
Glazed doors are framed and made from the same
species as the face veneer. Drawer bodies are NAUF
1/2” 9-ply Baltic Birch dovetailed at all four corners.
Powder coated cold rolled steel or stainless steel are
other drawer body options available. Drawer bottoms
are 1/4” hardboard or veneered panel that are let into
routed slots on all four sides of the drawer body and
hot glued along the entire perimeter on the bottom.
Drawers Fronts and doors are edgebanded with
hardwood of the same species as the face veneer.
Cabinets
Mott casework can meet the most demanding
specification, whether it is AWI Premium or an
architect's 'signature' specification. We manufacture
using premium grade techniques using material as
outlined by the architect or lab planner in the
specifications of each project. A variety of veneer panels
and glues are available to meet just about any
environmental, appearance, or durability requirement.
Most of our cabinets are available in SEFA compliant
versions; contact Mott for details.
Each base cabinet has a 1” thick top front rail and
optional intermediate rail, 3/4” thick top and bottom back
rails and are joined together with concealed hardwood
dowels and NAUF glue. The front exposed edge is
hardwood edgebanded in the same species as the face
veneer. Wall and floor cabinets have 1” top panels and
wall cabinets also have 1” bottom panels. Toe spaces
are 3” deep by 4” high.
Hardware
Doors that are 48” high and higher have at least three
hinges and doors that are less than 48” high have two
hinges. Standard hinges include five knuckle
stainless steel hinge, three knuckle barrel hinge, and
concealed European style hinge. Standard drawer
suspension is 100 lbs full extension runners, optional
75lbs nylon tire or 200lbs full extension are available.
File drawers are always 100lbs full extension. Glazed
doors are 1/4” clear laminated safety glass, 3mm float
glass or tempered glass held in place with a
removable clear plastic retainer. Sliding doors shall
be set in an extruded aluminum track.
All base cabinets have a full height removable back
panel. Drawer cabinets have an optional split back
panel. Sink cabinets have a partial back panel to
facilitate plumbing. Open and glazed cabinets have
veneered back panels.
CABINET SIDE
BASE CABINET DETAIL
REMOVABLE BACK
REAR RAIL
DRAWER SUPPORTS -14 GA GALV.
OPTIONAL INTERMEDIATE RAIL
TOP RAIL
DRAWER BOTTOM
DRAWER WITH INTEGRAL
SIDES & BACK
DOOR FRONT
ROLLER
CATCHES
Shelves
All shelves are made from veneer core panel
product of the same species specified for the
face veneer. Shelves are 1” thick and are
adjustable on 1-1/4” increments and held in
place via single pin supports or seismic plastic
twin pin supports. The front is hardwood
edgebanded in the same species as the face
veneer.
Table Frames and Apron Panels
Frames are 3-3/4” high and 3/4” thick lumber.
Legs are 2-1/8” X 2-1/8” solid lumber with 4”
high flexible shoes. Frames are bracketed and
securely bolted together (unless otherwise
noted).
FSC certified sustainable materials and no
added urea-formaldehyde (NAUF) are
available options.
Mott Manufacturing wood casework division is
working towards registering to the ISO 90012008 standard.
HINGE (See Page H9)
DRAWER FRONT
BOTTOM
ADJUSTABLE SHELF
ENCLOSED TOE SPACE (UNFINISHED)
All dimensions and sizes shown are nominal.
Specifications and details are based on product information at the time of printing and may change at any time without notice.
Mott Manufacturing reserves the right to change dimensions, specifications and manufacturing details at any time without notice.
H1
V.8.0
FURNITURE
FURNITURE
LABORATORY
WOOD CASEWORK
INTRODUCTION - TYPICAL WORK AREAS
Details
The following details are provided to illustrate how base cabinets, filler panels and countertops combine to
construct a laboratory work area.
60"
1524mm
12”
18”
or
457mm
11-1/2"
292mm
60"
1524mm
1"
25.4mm
22"
559mm
1"
25.4mm
22"
559mm
14"
356mm
1"
25.4mm
22"
559mm
14"
356mm
22"
559mm
30", 33” & 36"
or
762mm, 838mm
& 914mm
30", 33” & 36"
or
762mm, 838mm
& 914mm
! Above is an island type configuration with 60” wide counter
top, (2) 22” deep cabinets, and a 14” removable filler panel.
! The area covered by the 14” removable filler panel
provides a large accessible space for required services.
! Both base cabinet side panels can also be extended to 29”
deep to eliminate the use of a 14” filler and provide a
continuous cabinet look, cabinet interior will remain 20-1/8”
deep.
! Above is an island type configuration with 60” wide counter
top, (2) 22” deep cabinets, a 14” removable filler panel and
12” reagent shelf.
! The area covered by the 14” removable filler panel
provides a large accessible space for required services.
! Both base cabinet side panels can also be extended to 29”
deep to eliminate the use of a 14” filler and provide a
continuous cabinet look, cabinet interior will remain 20-1/8”
deep.
30"
762mm
24"
609mm
1"
25.4mm
22"
559mm
1"
25.4mm
7"
1"
25.4mm
178mm
25.4mm
1"
30", 30” & 36"
or
762mm, 838mm
& 914mm
30", 33” & 36"
or
762mm, 838mm
& 914mm
! Above is a base cabinet configuration with 30” deep
counter top, 22” deep base cabinet and 7” removable filler
panel.
! The area covered by the 7” removable filler panel provides
accessible space for required services.
! Base cabinet side panels can also be extended to 29” deep
to eliminate the use of a 7” filler and provide a continuous
cabinet look, cabinet interior will remain 20-1/8” deep.
! Above is a standard base cabinet configuration with 24”
deep counter top, 22” deep base cabinet and 1” filler panel.
! Base cabinet side panels can also be extended to 23” deep
to eliminate the use of a 1” filler and provide a continuous
cabinet look, cabinet interior will remain 20-1/8” deep.
All dimensions and sizes shown are nominal.
Specifications and details are based on product information at the time of printing and may change at any time without notice.
Mott Manufacturing reserves the right to change dimensions, specifications and manufacturing details at any time without notice.
22"
559mm
H2
V.8.0
LABORATORY
FURNITURE
FURNITURE
WOOD CASEWORK
INTRODUCTION - OPTIONAL METRIC SIZES
B ase Cabinets
Mott base cabinets are also available in metric widths of 513mm or 1000mm. The information below indicates the
dimensions of metric base cabinets. To order metric base cabinets contact your nearest Mott dealer.
883mm
(standing height)
or
838mm
(ADA height)
or
730mm
(sitting height)
883mm
(standing height)
or
838mm
(ADA height)
or
730mm
(sitting height)
1000mm
513mm
559mm
or
457mm
Note: 457mm available on selected
specialty cabinets only.
Wall Cabinets
Mott wall cabinets are also available in metric widths of 513mm or 1000mm. The information below indicates the
dimensions of metric wall cabinets. To order metric wall cabinets contact your nearest Mott dealer.
1219mm
914mm
762mm
610mm
1219mm
914mm
762mm
610mm
513mm
356mm
457mm
1000mm
All dimensions and sizes shown are nominal.
Specifications and details are based on product information at the time of printing and may change at any time without notice.
Mott Manufacturing reserves the right to change dimensions, specifications and manufacturing details at any time without notice.
H3
V.8.0
LABORATORY
FURNITURE
FURNITURE
WOOD CASEWORK
INTRODUCTION - OPTIONAL METRIC SIZES
Floor Cabinets
Mott floor cabinets are also available in metric widths of 513mm or 1000mm. The information below indicates the
dimensions of metric floor cabinets. To order metric floor cabinets contact your nearest Mott dealer.
2133mm
2133mm
457mm
or
559mm
1000mm
513mm
A prons and Tables
Mott aprons and tables are also available in metric widths of 513mm, 1000mm and 1513mm. The information
below indicates the dimensions of metric aprons and tables. To order metric aprons and tables contact your
nearest Mott dealer.
883mm
838mm
(ADA height)
730mm
513mm
1000mm
1513mm
559mm
711mm
Miscellaneous Items
Mott miscellaneous items such as filler panels, service drops etc. are also available in metric widths. To order
these items contact your nearest Mott dealer.
All dimensions and sizes shown are nominal.
Specifications and details are based on product information at the time of printing and may change at any time without notice.
Mott Manufacturing reserves the right to change dimensions, specifications and manufacturing details at any time without notice.
H4
V.8.0
LABORATORY
FURNITURE
FURNITURE
WOOD CASEWORK
PRODUCT SIZES AND DIMENSIONS
B ase Cabinets
34-3/4”
31-3/4”
28-3/4”
22”
22”
STANDING HEIGHT
22”
22”
ADA HEIGHT
SITTING HEIGHT
Note: Lipped Overlay
cabinets with door and
drawer fronts are 3/8" less
than standard depths.
Wall Cabinets
48”
36”
30”
24”
Note: Lipped Overlay
cabinets with door and
drawer fronts are 3/8" less
than standard depths.
14” & 18”
14” & 18”
14” & 18”
14” & 18”
Floor Cabinets
84”
Note: Lipped Overlay
cabinets with door and
drawer fronts are 3/8" less
than standard depths.
14”, 18” & 22”
All dimensions and sizes shown are nominal.
Specifications and details are based on product information at the time of printing and may change at any time without notice.
Mott Manufacturing reserves the right to change dimensions, specifications and manufacturing details at any time without notice.
H5
V.8.0
FURNITURE
FURNITURE
LABORATORY
WOOD CASEWORK
OPTIONS
Standard Options
Standard Options
VENEER TYPE:
STAIN TYPE:
RED OAK - PLAIN SLICED
RED OAK - RIFT CUT
MAPLE - PLAIN SLICED
MAPLE - QUARTER SLICED
MAPLE - ROTARY SLICED
BAMBOO - NATURAL
BAMBOO - CARAMELIZED, EDGE CUT
BAMBOO - EDGE CUT
BEECH - QUARTER SLICED
BEECH - EUROPEAN STEAMED
BIRCH - ROTARY SLICED
CHERRY - PLAIN SLICED
RIBBON SAPELE - QUARTER SLICED
WHITE SAPELE - QUARTER SLICED
ANIGRE - QUARTERED W/ PLAIN FIGURE
GRAIN MATCH:
BOOK MATCHED
SLIP MATCHED
SEQUENCE MATCHED
SAME FLITCH BOOK MATCHED
SAME FLITCH RUNNING MATCHED
OTHER (SPECIFY)
NATURAL
CASHEW
GINGER
TOFFEE
CIDER
HAZELNUT
FINISHES:
OTHER
Meets SEFA 8 Standard
CABINET CONSTRUCTION:
OTHER
Meets SEFA 8
OVERLAY STYLE:
1/16”
1/8”
1/8”
22”
1/16”
1/8”
1/4”
1/8”
1/8”
1/4”
22”
1/8”
REVEAL OVERLAY
No notching on doors with balanced reveals
FULL FLUSH OVERLAY Standard
Flush Overlay cabinet fronts provide tight
reveals by notching around the hinge
1/8”
½”
½”
21-5/8”
3/4”
1/8”
LIPPED OVERLAY
Lipped Overlay cabinet fronts have a
combination grain direction
CABINET CORE:
VENEER CORE PLYWOOD Standard
On the sides and bottom
PARTICLEBOARD CORE PLYWOOD
On the sides and bottom
MDF CORE
On the sides and bottom
COMBINATION CORE
DOOR AND DRAWER CORE:
PARTICLEBOARD CORE PLYWOOD Standard
COMBINATION CORE
MDF CORE
All dimensions and sizes shown are nominal.
Specifications and details are based on product information at the time of printing and may change at any time without notice.
Mott Manufacturing reserves the right to change dimensions, specifications and manufacturing details at any time without notice.
H6
V.8.0
LABORATORY
FURNITURE
FURNITURE
WOOD CASEWORK
OPTIONS
Standard Options
CABINET TOP FRAME:
FRONT AND BACK RAILS Standard
Front horizontal and rear vertical rail
FULL TOP FRAME
Front, rear and side vertical rails
EDGEBANDING:
ROLL TYPE EDGE BAND Standard
100% hardwood, 1/8” thick
STICK EDGE BAND
1/8” thick
STICK EDGE BAND
1/4” thick
GRAIN DIRECTION:
VERTICAL MATCHED Standard
Both drawers and doors have a vertical
matched grain direction
COMBINATION
Drawer grain direction is horizontal and door
grain direction is vertical
B ASE - CONSTRUCTION:
INTEGRAL WITH END PANELS,
WITHOUT LEVELERS Standard
INTEGRAL WITH END PANELS,
WITH LEVELERS
SEPARATE
Factory attached or field furnished/ fabricated
REMOVABLE BASE CABINET BACK PANEL:
ONE PIECE TEMPERED HARDBOARD
Standard
One piece behind cupboard units
Open behind drawers
WHITE MELAMINE - 1 PIECE
VENEERED - 1 PIECE
TWO PIECE TEMPERED HARDBOARD
Allows for easy access to portions of the cabinet
WHITE MELAMINE - 2 PIECE
VENEERED - 2 PIECE
REMOVABLE BACK OTHER (SPECIFY)
FINISHED ENDS OPTION:
The Finished Ends Option is available for any unit you wish to have finished, that is exposed. Ends where this option is not selected will be manufactured from the same species of
material at a different grade level. All unfinished ends will have a sealer coat applied.
OPTION FEB
Finished Ends Both
OPTION FEL
Finished End Left
OPTION FER
Finished End Right
All dimensions and sizes shown are nominal.
Specifications and details are based on product information at the time of printing and may change at any time without notice.
Mott Manufacturing reserves the right to change dimensions, specifications and manufacturing details at any time without notice.
H7
V.8.0
FURNITURE
FURNITURE
LABORATORY
WOOD CASEWORK
OPTIONS
Standard Options
EXTENDED ENDS OPTION:
The Extended Ends Option is available in 1” increments from 1” to 9” on any unit you wish to have extended. When choosing this option change the last digit to the extended length
you require. Eg: XB1 = Extended End Both of 1”. This option comes standard as a finished end.
OPTION XB7
Extended Ends Both
OPTION XL7
Extended End Left
OPTION XR7
Extended End Right
FIXED BACK AT TALL CASE/WALL CASE/UPPER CASE ONLY (solid doors only):
TEMPERED HARDBOARD Standard
VENEER MDF CORE PLYWOOD
VENEERED BACK
DRAWER CONSTRUCTION:
DOVETAIL DRAWER BODIES Standard
All four wood sides connected by multiple dovetail
joints. Sides slotted for bottom panel
Solid Maple Drawer Body, Option DBM
POWDER COATED STEEL DRAWER
BODIES
One full piece of powder coated 20ga rolled
steel with reinforcing bend on all top edges
STAINLESS STEEL DRAWER BODIES
Drawer with integral sides and back,
constructed using 20ga 304 stainless steel
with a #4 finish
3/4 EXTENSION SLIDES
OPTION DR2 3/4 extension epoxy coated
nylon tire slides
FULL EXTENSION SLIDES
OPTION DR5 for 200lb
HALF DEPTH SHELF
Accommodates storage of tall apparatus in
front of shelf
SPLIT DEPTH SHELF
Capable being a Half Depth and a Full Depth
shelf
DRAWER SUSPENSION:
FULL EXTENSION SLIDES Standard
OPTION DR1 for full extension 100 lb, galvanized
steel slides
CABINET SHELF DEPTH:
FULL DEPTH SHELF Standard
Measures 3/4” shorter than the inside depth of
cabinet
All dimensions and sizes shown are nominal.
Specifications and details are based on product information at the time of printing and may change at any time without notice.
Mott Manufacturing reserves the right to change dimensions, specifications and manufacturing details at any time without notice.
H8
V.8.0
LABORATORY
FURNITURE
FURNITURE
WOOD CASEWORK
OPTIONS
Standard Options
DRAWER/DOOR PULL DIRECTION:
CONFIGURATION 1 Standard
Pulls are horizontal on all drawers, and vertical
on all doors
CONFIGURATION 2
Pulls are horizontal on all drawers and doors.
Floor cabinets have vertical pulls
DRAWER/DOOR PULLS:
OPTION 62 - Standard
4” Brushed Aluminum Pull
OPTION 61
4” Tubular Stainless Steel Pull
OPTION 68
4” Aluminum Wire Pull
OPTION 6B
4” Black Wire Pull
OPTION 60
4” Black Nylon Pull
OPTION 63
4” Chrome Pull
OPTION 65
4” Flush Aluminum Pull
DOOR HINGES:
OPTION 20 - Standard
Dull Chrome Overlay Hinge
OPTION 24
Stainless Steel Overlay Hinge
OPTION DH2
Black Overlay Hinge
OPTION 27
Three Knuckle Hinge
OPTION 28
165 Degree Euro Concealed Self-Closing Hinge
DOOR CATCHES:
ROLLER CATCH Standard
MAGNETIC CATCH
SHELF CLIPS:
PLASTIC TWIN-PIN Standard
Seismic suited
PLASTIC SINGLE-PIN
Seismic suited
PLATED PIN
Allows for easy adjustability
All dimensions and sizes shown are nominal.
Specifications and details are based on product information at the time of printing and may change at any time without notice.
Mott Manufacturing reserves the right to change dimensions, specifications and manufacturing details at any time without notice.
RECESSED MOUNTING PILASTER
AND CLIPS
H9
V.8.0
LABORATORY
FURNITURE
FURNITURE
WOOD CASEWORK
OPTIONS
Standard Options
L OCK TYPE:
OPTION 30 Standard
5-Disc Master with removable core
OPTION LK4
5-Pin Tumbler with removable core,
3 level keying
OPTION 37
Provisions for Hasp Lock
(lock not included)
SECURITY PANELS:
WITHOUT FRONT RAILS Standard
When no locks are selected
WITH FRONT RAILS
When cabinets are to be keyed alike
WITH FRONT RAILS & SECURITY PANEL
When cabinets are to be keyed different
L ABEL HOLDER:
NONE Standard
OPTION 02
Label holder - one per door, one per
drawer
OPTION LH2
Label holder - File drawers only
OPTION LH3
Label holder - all drawers only
GLASS:
FLOAT GLASS Standard
3mm glass
LAMINATED SAFETY GLASS
6mm
TEMPERED SAFETY GLASS
6mm
FLOAT GLASS with Flush Pull
6mm glass
All dimensions and sizes shown are nominal.
Specifications and details are based on product information at the time of printing and may change at any time without notice.
Mott Manufacturing reserves the right to change dimensions, specifications and manufacturing details at any time without notice.
H10
V.8.0
LABORATORY
FURNITURE
FURNITURE
WOOD CASEWORK
OPTIONS
Ordering Special Features
STEP TWO - OPTIONAL FEATURES
Select any of the following options as the application requires.
Option #
Description
Cabinet & Miscellaneous Options
00
Required cabinet has drawer and/or door configuration similar to basic part noted. A minor
configuration change is required with no changes in the cabinets outside dimensions from
the basic part number specified - see note 1
02
Label holders on all doors/drawers
03
Numeric or alpha identification disks on all doors/drawers - see note 2
04
Standard louver configuration on doors - see note 3
05
Non-standard louver configuration on doors - see note 1
07
Cut-outs for electrical and/or plumbing services - see note 1
08
Security panel installed
09
Stainless steel waste flap
10
One drawer divider per drawer - see note 12
11
Multiple drawer dividers per drawer - see note 1
12
Pull out writing board supplied with same veneer as cabinet exterior
13
Pull out writing board supplied with high pressure laminate writing surface
14
Ventilation grill in toe kick base - see note 1
15
Finished back on cabinet
17
Nylon levelers
19
Full width drawer on 5” high apron
37
Provisions for hasp locks (actual locks not included)
48
Keyboard tray (replace drawer)
82
FRP liner for acid cabinets - see note 4
83
Self closing doors for solvent cabinets
84
Galvanized bin insert
85
PVC bin insert for waste bin units
89
Lazy susan storage unit for corner cabinets
90
Sink supports - see note 6
AD
Add - a - drawer design - see note 15
BL
“Base” label (use this option code to replace standard label on Acid cabinets)
CL
“Corrosive” label
DL
Fluorescent light for specialty recessed drawer desk unit
F1
Finished top
F2
Finished top and back
FL
Fusible Link with self closer for Insulated Solvent Unit - see note 7
LA
Bilingual label (English/French)
LF
Longitudinal file
NB
No base on cabinet to sit on floor
NC
No base on cabinet to sit on curb
NF
Pump Cabinet Unit with no cabinet floor and toekick is integral with door
NFD
Pump Cabinet Unit with no cabinet floor and toe kick is integral with door, dolly included
PC
Foot pedal cutouts centered
PL
Foot pedal cutout left hand side
PR
Foot pedal cutout right hand side
RB
Removable back on drawer cabinet
RL
Remote LED light for narcotic cabinet
SK
Skid item
All dimensions and sizes shown are nominal.
Specifications and details are based on product information at the time of printing and may change at any time without notice.
Mott Manufacturing reserves the right to change dimensions, specifications and manufacturing details at any time without notice.
H11
V.8.0
LABORATORY
FURNITURE
FURNITURE
WOOD CASEWORK
OPTIONS
Ordering Special Features
STEP TWO - OPTIONAL FEATURES
Select any of the following options as the application requires.
Option #
Description
Cabinet & Miscellaneous Options
SP
Silk Screen Printing (to replace standard labels on Acid and/or Flammable cabinets)
VK
Corrugated polyolefin vent kit for acid cabinets
T1
One pull out tray on full extension runners with 1” high lip - see note 16
T2
Two pull out trays on full extension runners with 1” high lip - see note 16
T3
Three pull out trays on full extension runners with 1” high lip - see note 16
40
One extra cabinet shelf - see note 5
41
Two extra cabinet shelves - see note 5
42
One interior cabinet shelf on full extension runners - see note 13
43
Two interior cabinet shelves on full extension runners - see note 13
44
Three interior cabinet shelves on full extension runners - see note 13
Wall Cabinet Options
SL
DS
Seismic lip
Double sided wall cabinet
Floor Cabinet Options
80
Full height doors for floor cabinets
81
Coat rod for wardrobe for floor cabinets
Shelf Options - See page N8
Glass Options
45
46
47
4A
GL1
Base Cabinet Options
70
71
72
73
74
75
76
77
78
79
DuoLite safety glass - see note 11
Tempered glass - see note 11
Customer specified glass - see note 8
Glass Tint 44% (Grey Smoke)
3mm float glass
Front toe kick
Toe kick - front & left side - see note 14
Toe kick - front & right side - see note 14
Toe kick - front & 2 sides - see note 14
Toe kick - front & back - see note 14
Toe kick - front, back, & 2 sides - see note 14
Replace toe kick base with 4 legs
Replace cabinet toe kick base with casters and tip prevention counterweights
(casters & hardware shipped loose)
Replace cabinet toe kick base with customer specified casters - see note 8
Other customer specified base and/or toe kick - see note 1
All dimensions and sizes shown are nominal.
Specifications and details are based on product information at the time of printing and may change at any time without notice.
Mott Manufacturing reserves the right to change dimensions, specifications and manufacturing details at any time without notice.
H12
V.8.0
LABORATORY
FURNITURE
FURNITURE
WOOD CASEWORK
OPTIONS
Ordering Special Features
STEP TWO - OPTIONAL FEATURES
Select any of the following options as the application requires.
Option #
Table Options
06
48
49
87
88
91
92
93
94
95
Description
One fixed shelf on “O” frame tables
Keyboard tray (replaces drawer)
Wood leg with stainless steel adjustable height inserts. Legs are adjustable in 1”
increments, from 28-3/4” high to 34-3/4” high.
Mobile table complete with casters - see note 10
Mobile table complete with customer specified casters - see note 8
Table with no supports
“U” frame style table with rear & side supports
Left side leg table - no supports
Right side leg table - no supports
Front table legs - no supports
EXPLANATORY NOTES FOR OPTION CODES
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
Full dimensional and descriptive details (preferably including a sketch) must be included with
the order.
Full descriptive details must be included with the order.
Standard louver configuration is one block of 6 louvers located near the bottom center of
each door, each louver is approximately 3” wide by 5-1/2” long.
Use this option code to have cabinet lined with FRP instead of molded liner.
Standard number of removable shelves per base cabinet with door(s) or wall cabinet is noted
in the cabinet drawings of this catalog.
Sink support kit is required for under-counter mounted sinks used with Imperial Stone or
Epoxy counter tops. Sink support kit not normally required for self rimming or integrally
welded sinks.
Designed for use on solvent cabinets (-83). A fusible link holds doors open during use and
melts at 165°F to automatically close doors in the event of a fire.
Provide complete specification and source for all special option ordered.
Standard lock is a 5 pin disc lock. Every lock on every cabinet on order will be keyed alike
unless otherwise specified.
Standard 4” high casters are swivel with rolling brake.
Standard glass is as follows:
All framed glass and sliding glass Floor Cabinets
1/4” (6mm) float glass
Sliding glass door Wall Cabinets
1/4” (6mm) float glass
Framed glass door Wall Cabinets
1/8” (3mm) float glass
Drawer divider runs depth of drawer.
Pull out shelves replace standard removable shelf in base cabinets with door(s).
Cabinet left and right are determined when facing the cabinet front.
Removable top drawer unit is 6” high.
Pull out tray replaces standard removable shelf in base cabinets with door(s). Tray is not
removable.
All dimensions and sizes shown are nominal.
Specifications and details are based on product information at the time of printing and may change at any time without notice.
Mott Manufacturing reserves the right to change dimensions, specifications and manufacturing details at any time without notice.
H13
V.8.0
FURNITURE
FURNITURE
LABORATORY
WOOD CASEWORK
OPTIONS
Ordering Double Sided Wall Units
Mott laboratory furniture is available with a wide variety of features to meet specific application requirements. The
full range of our Mott wall cabinets are available in our double sided design. To specify double sided wall
cabinets, select the two digit part number suffix from below and add this suffix after the standard part number,
separated with a dash.
OVERVIEW EXAMPLE
To order double sided wall cabinets.
5410060W-DS
Double sided wall cabinet option
Wall cabinet - 30” high from page J3
Note
e: Steel cabinet drawings shown.
5410060W
5410060W-DS
Ordering Special Features
Mott laboratory furniture is available with a wide variety of features to meet specific application requirements. To
specify any feature, select the two or three digit option code suffix from the list below and add this suffix after the
standard part number, separated with a dash.
OVERVIEW EXAMPLE
To order chrome hinges, brushed aluminum pulls, and a pull-out shelf on a drawer/door cabinet.
1410022W-21-62-42
One interior cabinet shelf on pull out runners - page H12
Brushed aluminum pulls - page H8
Chrome hinges - page H8
Base cabinet - standing height from page I1
All dimensions and sizes shown are nominal.
Specifications and details are based on product information at the time of printing and may change at any time without notice.
Mott Manufacturing reserves the right to change dimensions, specifications and manufacturing details at any time without notice.
H14
V.8.0
LABORATORY
FURNITURE
FURNITURE
WOOD CASEWORK
OPTIONS
L ock and Key Options
All Locks Keyed Different Per Unit
Individual Locks
Locks are keyed different per unit from
other units.
Note: This is the standard key schedule
with disc tumbler lock supplied for option
code 30 unless otherwise specified.
Individual Keys
Lock Sets
Single Key/Set
A ll Locks Keyed Alike
Individual
Locks
All locks are keyed alike, each lock can be
opened with a single key.
Single Key
All Locks Keyed Different
Individual
Locks
Locks are keyed different from other locks.
Up to 229 key changes for disc are
available.
Individual
Keys
Locks Keyed Alike in Sets
Lock Sets
Locks are keyed alike in sets. Only one key
will open one set of locks within the set. Up
to 229 key changes for disc are available.
Single Key/Set
Master Keys
Master Keyed Locks
All locks are keyed different from all other
locks. Each set within a group can be
opened with a master key. Up to 229 key
changes for disc are available.
Individual
Locks
Individual
Keys
Grand Master Key
All Pin Locks Keyed Different Grand Master & Master Keyed
All locks are keyed different from all other
locks. Each set within a group can be
opened with a master key. All groups can
be opened with a grand master key.
Grand Master only available in pin style
locks.
Master Keys
Individual
Locks
Individual
Keys
All dimensions and sizes shown are nominal.
Specifications and details are based on product information at the time of printing and may change at any time without notice.
Mott Manufacturing reserves the right to change dimensions, specifications and manufacturing details at any time without notice.
H15
V.8.0
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising