Gigabit Ethernet-SX PCI-X Adapter Installation and Using

Gigabit Ethernet-SX PCI-X Adapter Installation and Using
Installation and Using Guide
REFERENCE
86 A1 18EG 00
ESCALA
Gigabit
Ethernet-SX PCI-X
Adapter
ESCALA
Gigabit Ethernet-SX
PCI-X Adapter
Installation and Using Guide
Hardware
November 2002
BULL CEDOC
357 AVENUE PATTON
B.P.20845
49008 ANGERS CEDEX 01
FRANCE
REFERENCE
86 A1 18EG 00
The following copyright notice protects this book under Copyright laws which prohibit such actions as, but not
limited to, copying, distributing, modifying, and making derivative works.
Copyright
Bull SAS 1992, 2002
Printed in France
Suggestions and criticisms concerning the form, content, and presentation of this
book are invited. A form is provided at the end of this book for this purpose.
To order additional copies of this book or other Bull Technical Publications, you
are invited to use the Ordering Form also provided at the end of this book.
Trademarks and Acknowledgements
We acknowledge the right of proprietors of trademarks mentioned in this book.
AIX® is a registered trademark of International Business Machines Corporation, and is being used under licence.
UNIX® is a registered trademark in the United States of America and other countries licensed exclusively through
the Open Group.
Linux® is the registered trademark of Linus Torvalds in the U.S. and other countries
The information in this document is subject to change without notice. Bull will not be liable for errors contained
herein, or for incidental or consequential damages in connection with the use of this material.
Contents
Safety Information.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. v
Handling Static-Sensitive Devices . . . . . . . . . . . . . . . . . vii
Electrostatic Discharge Protection. . . . . . . . . . . . . . . . . . vii
About This Book .
ISO 9000 . . . .
Related Publications
Trademarks . . .
. . . . . . . . . . . . . . . . . . . . . . ix
. . . . . . . . . . . . . . . . . . . . . . ix
. . . . . . . . . . . . . . . . . . . . . . ix
. . . . . . . . . . . . . . . . . . . . . . ix
Chapter 1. Overview .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 1
Chapter 2. Preparing for Installation
Verifying Your Hardware Requirements
Verifying Your Software Requirements
Checking Your Package . . . . .
Gathering Tools and Documentation .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Chapter 3. Installing the Device Driver Software .
Verify AIX Software Installation . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 5
. 6
Chapter 4. Installing the Gigabit Ethernet-SX
Installing the Adapter . . . . . . . . .
Verifying the Installation . . . . . . . .
Running Adapter Diagnostics . . . . . .
3
3
3
4
4
PCI-X Adapter . . . . . . . . 9
. . . . . . . . . . . . . 9
. . . . . . . . . . . . . 9
. . . . . . . . . . . . . 10
Chapter 5. Connecting to an Ethernet Network . . . . . . . . . . . . 11
Connecting the Network Cables and Adapter . . . . . . . . . . . . . . 11
Understanding the Adapter LED . . . . . . . . . . . . . . . . . . 12
Appendix A. Communications Statements . . . . . . . . . . . .
Federal Communications Commission (FCC) Statement . . . . . . . .
European Union (EU) Statement . . . . . . . . . . . . . . . .
International Electrotechnical Commission (IEC) Statement . . . . . . .
United Kingdom Telecommunications Safety Requirements . . . . . . .
Avis de conformité aux normes du ministère des Communications du Canada .
Canadian Department of Communications Compliance Statement . . . . .
VCCI Statement . . . . . . . . . . . . . . . . . . . . .
Electromagnetic Interference (EMI) Statement - Taiwan . . . . . . . .
Radio Protection for Germany . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Appendix B. Notices
.
. 17
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
13
13
13
14
14
14
14
14
15
15
iii
iv
Gigabit Ethernet-SX PCI-X Adapter Installation and Using Guide
Safety Information
DANGER
An electrical outlet that is not correctly wired could place hazardous voltage
on metal parts of the system or the devices that attach to the system. It is the
responsibility of the customer to ensure that the outlet is correctly wired and
grounded to prevent an electrical shock.
Before installing or removing signal cables, ensure that the power cables for
the system unit and all attached devices are unplugged.
When adding or removing any additional devices to or from the system,
ensure that the power cables for those devices are unplugged before the
signal cables are connected. If possible, disconnect all power cables from the
existing system before you add a device.
Use one hand, when possible, to connect or disconnect signal cables to
prevent a possible shock from touching two surfaces with different electrical
potentials.
During an electrical storm, do not connect cables for display stations, printers,
telephones, or station protectors for communication lines.
v
vi
Gigabit Ethernet-SX PCI-X Adapter Installation and Using Guide
Handling Static-Sensitive Devices
Attention: Static electricity can damage this device and your equipment. Leave the
Gigabit Ethernet-SX PCI-X Adapter in its anti-static protective bag until you are ready to
install it in your system unit
Electrostatic Discharge Protection
Take the following precautions whenever you handle the Gigabit Ethernet-SX PCI-X
Adapter or other static devices:
v If you have an anti-static wrist strap, use it while handling the adapter.
v Limit your movement. Movement can cause static electricity to build up around you.
v While the adapter is still in its anti-static package, touch it to an unpainted metal part
of the system unit, such as an expansion slot.
v Holding the adapter carefully by its edges. Avoid touching solder joints, pins, or other
printed circuitry.
v Do not leave the device where others can handle and possibly damage the device.
v Remove the adapter from its package and install it directly into the system unit. If it is
necessary to set the device down, place it back into its static-protective package.
Before you pick it up again, touch the bag and metal frame of the system unit at the
same time.
v Be careful when you hand the adapter during cold weather, as low humidity and
heating increase static electricity.
vii
viii
Gigabit Ethernet-SX PCI-X Adapter Installation and Using Guide
About This Book
This book provides information about the Gigabit Ethernet-SX PCI-X Adapter, how to
install and configure the adapter, and how to attach the adapter to a network. Use this
book together with your specific system unit and operating system documentation.
ISO 9000
ISO 9000 registered quality systems were used in the development and manufacturing
of this product.
Related Publications
The following publications contain related information:
v System unit documentation for information specific to your hardware configuration
v Operating system documentation for information specific to your software
configuration
v PCI Adapter Placement Reference Guide (for the latest version, you may need to
contact your marketing representative)
Trademarks
The following term is a trademark of International Business Machines Corporation in the
United States, other countries, or both:
v AIX
v AIX 5L
Other company, product, and service names may be trademarks or service marks of
others.
ix
x
Gigabit Ethernet-SX PCI-X Adapter Installation and Using Guide
Chapter 1. Overview
The Gigabit Ethernet-SX PCI-X Adapter is a high performance, highly integrated,
universal, Ethernet LAN adapter for PCI-X and PCI systems. The adapter provides
1000 Mbps throughput on a standard shortwave (850 nm) 50/62.5 micron multimode
optical cable and conforms to the IEEE 802.3z standards and supports distances of 260
meters for 62.5u MMF and 550 meters for 50.0u MMF.
The adapter runs in standard PCI-X V1.0a compliant systems with 32/64-bit PCI-X Bus
Master slots at 66/133 MHz, as well as PCI 2.2 compliant systems with 32/64-bit PCI
bus master slots at 33/66 MHz.
The Gigabit Ethernet-SX PCI-X Adapter provides the following features:
v Support for 64 bit Direct Bus Mastering on the PCI/PCI-X bus
v Uses a shared memory structure in host memory and copies data directly from and
to host memory
v Supports Boot ROM
v 1000 Mbps Full Duplex throughput on standard 50u or 62.5u MMF optical cable
v IEEE 802.3z 1000 Base-SX compliant
v Supports Dual address cycle for access to 64-bit addresses
v Supports 64-bit addressing for systems with greater than 4 GB of physical memory
v Supports PCI-X split transactions
v Surface mount technology (SMT)
v LC physical connector
1
ACT / LNK
2
Figure 1. Gigabit Ethernet-SX PCI-X Adapter
1. LED
2. Multimode Fiber LC Receptacle
1
2
Gigabit Ethernet-SX PCI-X Adapter Installation and Using Guide
Chapter 2. Preparing for Installation
This chapter helps you prepare to install your Gigabit Ethernet-SX PCI-X Adapter.
Preparing to install the adapter involves the following tasks:
v Verifying your hardware requirements
v Verifying your software requirements
v Making sure your package is complete
v Gathering tools and documentation
Note: If you are installing your operating system at this time, install the adapter before
you install the operating system (see “Installing the Adapter” on page 9 for
instructions).
If you are installing only the device driver for this adapter, install the device driver
before you install the adapter. (See Chapter 3, “Installing the Device Driver
Software” on page 5 for instructions.)
Verifying Your Hardware Requirements
The Gigabit Ethernet-SX PCI-X Adapter requires the following hardware:
__
A wrap plug for the multimode fiber connector, if you are running the total
diagnostics package
__
Shortwave (850 nm) 50/62.5 micron multimode fiber network attachment
The following table shows the minimum and maximum allowable cable lengths from the
adapter to the gigabit Ethernet switch, including patch cables:
Fiber Type
Modal bandwidth
(MHz-km)
Minimum range
(meters)
Maximum range
(meters)
62.5 µm MMF
160
2
220
62.5 µm MMF
200
2
275
50 µm MMF
400
2
500
50 µm MMF
500
2
500
Verifying Your Software Requirements
The Gigabit Ethernet-SX PCI-X Adapter is supported on AIX 5L for POWER version
5.1.35 with the 5100-03 Recommended Maintenance package (APAR IY32749) and
later. Ensure that your operating system supports this adapter before you install it.
Contact your support representative for assistance.
3
Checking Your Package
Check that the package contains the following items:
__
The Gigabit Ethernet-SX PCI-X Adapter
__
AIX device driver CD-ROM
__
Wrap plug
__
A registration card
Contact the place of purchase if an item is missing or damaged.
Note: Be sure to retain your proof of purchase as it might be required to receive
warranty service.
Gathering Tools and Documentation
To install the adapter, you need the following items:
4
__
A flat-blade screwdriver
__
Your system unit documentation, including any service manual
__
Your operating system documentation
Gigabit Ethernet-SX PCI-X Adapter Installation and Using Guide
Chapter 3. Installing the Device Driver Software
This chapter explains how to install the device driver for the Gigabit Ethernet-SX PCI-X
Adapter on an AIX system. The device driver is provided for the AIX operating system.
Be sure you have read Chapter 2, “Preparing for Installation” on page 3 to determine:
v If you should install your device driver software first, go to step 1 and continue with
this section.
v If you should install your adapter hardware first, go to Chapter 4, “Installing the
Gigabit Ethernet-SX PCI-X Adapter” on page 9. When you install AIX, your adapter
device driver automatically installs.
If your installed AIX operating system (AIX 5.1.35 and later) supports the Gigabit
Ethernet-SX PCI-X Adapter, the device driver is already installed and you can install the
adapter. Go to “Installing the Adapter” on page 9 for instructions.
To install the device driver software software, do the following:
1. Turn on the system unit power.
2. At the system prompt, log in as a root user.
3. Insert the media containing the device driver software into the appropriate media
device.
If your system does not have a CD-ROM drive, refer to your system
documentation for performing a NIM (Network Installation Management)
4. To start SMIT, type:
smitty devinst
Press Enter. The Install Additional Device Software panel displays. The INPUT
device/directory for software option is highlighted for selection.
5. Press F4 to display a list of input devices from which you can select. The cursor is
already positioned on the input entry field.
6. Either type the name of the input device in the entry field or select the appropriate
device, then press Enter. The Install Additional Device Software panel displays the
device you selected in the INPUT device/directory for software field. The
.SOFTWARE to install option is highlighted.
7. Press F4 to display a list of the device packages you can install.
8. To display a Find dialog box, type:
/
in the field where the cursor is positioned.
9. Type the following device package name:
devices.pci.14106802
Press Enter.
5
10. Press F7 to select the device package name, then press Enter. The Install
Additional Device Software panel displays the completed required fields.
11. Press Enter. The ARE YOU SURE list displays.
12. Press Enter. The COMMAND STATUS panel displays. The term RUNNING is
highlighted, indicating that the software is being installed.
13. When RUNNING changes to OK, scroll down to the bottom of the panel and locate
the Installation Summary. If the installation was successful, SUCCESS appears at the
bottom of the panel in the Result column of the Installation Summary.
14. Remove the device driver software media from the media device.
15. Press F10 to exit SMIT.
16. To shut down your system, type:
shutdown -F
Press Enter.
17. Go to “Installing the Adapter” on page 9.
Verify AIX Software Installation
To verify that the device driver for the Gigabit Ethernet-SX PCI-X Adapter is installed,
do the following:
1. If necessary, log in as root user.
2. At the command line, type:
lslpp -1 devices.pci.14106802.rte
3. Press Enter.
Possible results are as follows:
v If the Gigabit Ethernet-SX PCI-X Adapter device driver is installed, the following is
an example of the data that displays on your screen:
Fileset
Level
State
Description
----------------------------------------------------------------------Path: /usr/lib/objrepos
devices.pci.14106802.rte 5.1.35
COMMITTED
...Ethernet...
Adapter Software
Path: /etc/objrepos
5.1.35
devices.pci.14106802.rte
COMMITTED
...Ethernet...
Adapter Software
Verify that the filesets devices.pci.14106802.rte are installed at the AIX 5L for
POWER version 5.1.35 with the 5100-03 Recommended Maintenance package
(APAR IY32749) level or later.
If this information displays but you continue to have problems, go to Chapter 4,
“Installing the Gigabit Ethernet-SX PCI-X Adapter” on page 9.
v If no data displays on your screen, the Gigabit Ethernet-SX PCI-X Adapter device
driver did not install correctly. Return to Chapter 3, “Installing the Device Driver
Software” on page 5. Return to “Verifying the Installation” on page 9 and continue
with step 1 again.
6
Gigabit Ethernet-SX PCI-X Adapter Installation and Using Guide
If you continue to experience problems, it may be necessary to call your system
support organization. Refer to your operating system documentation for
instructions.
Chapter 3. Installing the Device Driver Software
7
8
Gigabit Ethernet-SX PCI-X Adapter Installation and Using Guide
Chapter 4. Installing the Gigabit Ethernet-SX PCI-X Adapter
After you install the device driver, you can install the Gigabit Ethernet-SX PCI-X
Adapter. This chapter takes you through the steps of installing your Gigabit Ethernet-SX
PCI-X Adapter which involves the following tasks:
v Installing the adapter in your system unit
v Verifying installation
v Running adapter diagnostics
Installing the Adapter
Before you begin, be sure to read the “Electrostatic Discharge Protection” on page vii
and Chapter 2, “Preparing for Installation” on page 3.
To install the adapter, do the following:
1. If your system supports hot-pluggable PCI adapters, refer to your system
documentation to install the adapter and return to “Verifying the Installation”. If your
system does not support hot plugging, continue with the next step.
2. Log in as a root user and type:
shutdown
at the system prompt and press Enter. When halt completed displays, turn off the
system unit power and unplug the power cord from the wall outlet.
Note: Refer to your system unit documentation for further shutdown information.
3. Remove the covers of your system unit. Follow the instructions provided in your
system unit documentation.
4. Install the adapter into an available PCI slot in your system unit. See the
instructions in your system unit documentation for installing PCI adapters. Refer to
your PCI Adapter Placement Reference guide for slot locations.
5. Follow the directions provided in your system unit documentation to reinstall the
covers of your system unit.
6. Plug the power cord back into the wall outlet.
7. Turn on the power to your system unit.
Note: It is recommended that you use a duplex cable with this adapter. If simplex
cables must be used, it is recommended that the two cables be clamped
together using a duplex clip, if available.
Verifying the Installation
See the instructions provided in your system unit documentation for verifying the
successful installation of the adapter. To verify, type:
lsdev -Cs pci
9
at the system prompt, then press Enter. A list of PCI devices displays. An Available
status indicates the the adapter is installed and ready to use.
Running Adapter Diagnostics
Diagnostics are provided with the device driver software. If you must run diagnostics,
refer to your system unit documentation for instructions.
10
Gigabit Ethernet-SX PCI-X Adapter Installation and Using Guide
Chapter 5. Connecting to an Ethernet Network
This chapter explains how to connect the adapter to the multimode fiber network.
Refer to your local procedures for information about connecting the Gigabit Ethernet-SX
PCI-X Adapter to your Ethernet network.
Note: Only one type of network can be attached to the adapter card at one time.
Connecting the Network Cables and Adapter
Before you begin connecting the adapter, make sure you have the hardware listed in
“Verifying Your Hardware Requirements” on page 3.
To connect the adapter to an multimode fiber network:
__ 1. Insert the male fiber LC connector of the fiber cable into the adapter LC
connector.
__ 2. Insert the male fiber LC connector of the other end of the cable into the network
switch.
Note: If your switch has an SC receptacle, you need an LC-SC convertor cable.
1
2
3
Figure 2. Connecting the Adapter to the Network
1. LC Fiber Optic Receptacle
2. LC Fiber Optic Plug
3. 62.5/50 MMF Cable
11
Understanding the Adapter LED
The LED on the Gigabit Ethernet-SX PCI-X Adapter provides information about the
card’s operation status. The LED is visible through the card’s mounting bracket and,
when lit, indicates the following conditions:
LED
Status
Off
On (Green)
Flashing (Green)
No Link/No Activity
Link, No Activity
Link, Activity
1
ACT / LNK
2
Figure 3. LED on the Gigabit Ethernet-SX PCI-X Adapter
1. LED
2. Multimode Fiber LC Receptacle
12
Gigabit Ethernet-SX PCI-X Adapter Installation and Using Guide
Appendix A. Communications Statements
The following statement applies to this product. The statement for other products
intended for use with this product appears in their accompanying documentation.
Federal Communications Commission (FCC) Statement
Note: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Properly shielded and grounded cables and connectors must be used in order to meet
FCC emission limits. Neither the provider nor the manufacturer is responsible for any
radio or television interference caused by using other than recommended cables and
connectors or by unauthorized changes or modifications to this equipment.
Unauthorized changes or modifications could void the user’s authority to operate the
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
European Union (EU) Statement
This product is in conformity with the protection requirements of EU Council Directive
89/336/EEC on the approximation of the laws of the Member States relating to
electromagnetic compatibility. The manufacturer cannot accept responsibility for any
failure to satisfy the protection requirements resulting from a non-recommended
modification of the product, including the fitting of option cards supplied by third parties.
Consult with your dealer or sales representative for details on your specific hardware.
This product has been tested and found to comply with the limits for Class A
Information Technology Equipment according to CISPR 22 / European Standard EN
55022. The limits for Class A equipment were derived for commercial and industrial
environments to provide reasonable protection against interference with licensed
communication equipment.
Attention: This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate
measures.
13
International Electrotechnical Commission (IEC) Statement
This product has been designed and built to comply with IEC Standard 950.
United Kingdom Telecommunications Safety Requirements
This equipment is manufactured to the International Safety Standard EN60950 and as
such is approved in the UK under the General Approval Number NS/G/1234/J/100003
for indirect connection to the public telecommunication network.
The network adapter interfaces housed within this equipment are approved separately,
each one having its own independent approval number. These interface adapters,
supplied by the manufacturer, do not use or contain excessive voltages. An excessive
voltage is one which exceeds 70.7 V peak ac or 120 V dc. They interface with this
equipment using Safe Extra Low Voltages only. In order to maintain the separate
(independent) approval of the manufacturer’s adapters, it is essential that other optional
cards, not supplied by the manufacturer, do not use main voltages or any other
excessive voltages. Seek advice from a competent engineer before installing other
adapters not supplied by the manufacturer.
Avis de conformité aux normes du ministère des Communications du Canada
Cet appareil numérique de la classe A respecte toutes les exigences du Réglement sur
le matériel brouilleur du Canada.
Canadian Department of Communications Compliance Statement
This Class A digital apparatus meets the requirements of the Canadian
Interference–Causing Equipment Regulations.
VCCI Statement
The following is a summary of the VCCI Japanese statement in the box above.
This is a Class A product based on the standard of the Voluntary Control Council for
Interference by Information Technology Equipment (VCCI). If this equipment is used in a
domestic environment, radio disturbance may arise. When such trouble occurs, the user
may be required to take corrective actions.
14
Gigabit Ethernet-SX PCI-X Adapter Installation and Using Guide
Electromagnetic Interference (EMI) Statement - Taiwan
The following is a summary of the EMI Taiwan statement above.
Warning: This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user will be required to take adequate measures.
Radio Protection for Germany
Dieses Gerät ist berechtigt in Übereinstimmung mit Dem deutschen EMVG vom
9.Nov.92 das EG–Konformitätszeichen zu führen.
Der Aussteller der Konformitätserklärung ist die IBM Germany.
Dieses Gerät erfüllt die Bedingungen der EN 55022 Klasse A. Für diese von Geräten
gilt folgende Bestimmung nach dem EMVG:
Geräte dürfen an Orten, für die sie nicht ausreichend entstört sind, nur mit besonderer
Genehmigung des Bundesministers für Post und Telekommunikation oder des
Bundesamtes für Post und Telekommunikation betrieben werden. Die Genehmigung
wird erteilt, wenn keine elektromagnetischen Störungen zu erwarten sind.
(Auszug aus dem EMVG vom 9.Nov.92, Para.3, Abs.4)
Hinweis
Dieses Genehmigungsverfahren ist von der Deutschen Bundespost noch nicht
veröffentlicht worden.
Appendix A. Preface
15
16
Gigabit Ethernet-SX PCI-X Adapter Installation and Using Guide
Appendix B. Notices
This information was developed for products and services offered in the U.S.A.
The manufacturer may not offer the products, services, or features discussed in this
document in other countries. Consult the manufacturer’s representative for information
on the products and services currently available in your area. Any reference to the
manufacturer’s product, program, or service is not intended to state or imply that only
that product, program, or service may be used. Any functionally equivalent product,
program, or service that does not infringe any intellectual property right of the
manufacturer may be used instead. However, it is the user’s responsibility to evaluate
and verify the operation of any product, program, or service.
The manufacturer may have patents or pending patent applications covering subject
matter described in this document. The furnishing of this document does not give you
any license to these patents. You can send license inquiries, in writing, to the
manufacturer.
The following paragraph does not apply to the United Kingdom or any country
where such provisions are inconsistent with local law: THIS MANUAL IS
PROVIDED ″AS IS″ WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. Some states do not allow disclaimer of express or implied warranties in
certain transactions; therefore, this statement may not apply to you.
This information could include technical inaccuracies or typographical errors. Changes
are periodically made to the information herein; these changes will be incorporated in
new editions of the publication. The manufacturer may make improvements and/or
changes in the product(s) and/or the program(s) described in this publication at any
time without notice.
Information concerning products made by other than the manufacturer was obtained
from the suppliers of those products, their published announcements, or other publicly
available sources. The manufacturer has not tested those products and cannot confirm
the accuracy of performance, compatibility or any other claims related to products made
by other than the manufacturer. Questions on the capabilities of products made by other
than the manufacturer should be addressed to the suppliers of those products.
17
18
Gigabit Ethernet-SX PCI-X Adapter Installation and Using Guide
Technical publication remarks form
Title :
ESCALA Gigabit Ethernet-SX PCI-X Adapter Installation and Using Guide
Reference Nº :
86 A1 18EG 00
Date:
November 2002
ERRORS IN PUBLICATION
SUGGESTIONS FOR IMPROVEMENT TO PUBLICATION
Your comments will be promptly investigated by qualified technical personnel and action will be taken as required.
If you require a written reply, please include your complete mailing address below.
NAME :
COMPANY :
ADDRESS :
Please give this technical publication remarks form to your BULL representative or mail to:
Bull - Documentation Dept.
1 Rue de Provence
BP 208
38432 ECHIROLLES CEDEX
FRANCE
info@frec.bull.fr
Date :
Technical publications ordering form
To order additional publications, please fill in a copy of this form and send it via mail to:
BULL CEDOC
357 AVENUE PATTON
B.P.20845
49008 ANGERS CEDEX 01
FRANCE
CEDOC Reference #
_ _
_ _
_ _ _ _
_
[ _ _ ]
_ _
_ _
_ _ _ _
_
[ _ _ ]
_ _
_ _
_ _ _ _
_
[ _ _ ]
_ _
_ _
_ _ _ _
_
[ _ _ ]
_ _
_ _
_ _ _ _
_
[ _ _ ]
_ _
_ _
_ _ _ _
_
[ _ _ ]
_ _
_ _
_ _ _ _
_
[ _ _ ]
_ _
_ _
_ _ _ _
_
[ _ _ ]
_ _
_ _
_ _ _ _
_
[ _ _ ]
_ _
_ _
_ _ _ _
_
[ _ _ ]
_ _
_ _
_ _ _ _
_
[ _ _ ]
_ _
_ _
_ _ _ _
_
[ _ _ ]
[ _ _ ]
Phone:
FAX:
E-Mail:
+33 (0) 2 41 73 72 66
+33 (0) 2 41 73 70 66
srv.Duplicopy@bull.net
Designation
Qty
: The latest revision will be provided if no revision number is given.
NAME:
Date:
COMPANY:
ADDRESS:
PHONE:
E-MAIL:
For Bull Subsidiaries:
Identification:
For Bull Affiliated Customers:
Customer Code:
For Bull Internal Customers:
Budgetary Section:
For Others: Please ask your Bull representative.
FAX:
BULL CEDOC
357 AVENUE PATTON
B.P.20845
49008 ANGERS CEDEX 01
FRANCE
REFERENCE
86 A1 18EG 00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising