Jeppesen Mobile FliteDeck User Guide

Jeppesen Mobile FliteDeck User Guide
Jeppesen Mobile FliteDeck User Guide
Jeppesen
55 Inverness Drive East
Englewood, Colorado 80112-5498
This document supports version 2.6.1 of Jeppesen Mobile FliteDeck.
Minimum operating system requirement for Jeppesen Mobile FliteDeck 2.6.1 is
iOS 7.0.
Copyright © 2014 Jeppesen. All rights reserved.
October 2014
Revision 1.0
Copyright © 2014 Jeppesen. All rights reserved.
Except as otherwise provided and authorized in a written agreement between both Jeppesen and your company, Jeppesen's
copyrighted information and materials may not be processed, reformatted, reproduced, stored in a retrieval system, or
transmitted in whole or in part, in any form or by any means, whether electrical, mechanical, photocopying, recording or
otherwise, without prior written permission of Jeppesen.
iPad is either a registered trademarks or trademark of Apple in the United States and/or other countries.
Product or brand names may be trademarks or registered trademarks of their respective owners.
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
About This Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Additional References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Release Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Release Identification Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hardware Supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connectivity Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Upgrade and Deployment Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
2
2
3
3
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Basic iPad Gestures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Global Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Sleep Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Flight Info - Allow Flight Sharing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Enroute View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Terminal Charts View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Weather . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Account Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Support Information and Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Setting Up Your Flight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
The Flight Info Drawer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
The Active Flight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
The Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Create a New Flight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Enter Airports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Enter Route Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Contents
Add SIDs and STARs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Editing Your Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Edit Your Route in the Flight Info Drawer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Edit Your Route by Interacting with the Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Edit Your Route with Rubber-Band Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Name and Save a User Waypoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Delete a User Waypoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Add a Radial DME Point to Your Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18
18
19
19
Working with Saved Flights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Save the Active Flight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
View Saved Flights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Load a Saved Flight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sort Saved Flights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Duplicate a Saved Flight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Delete Saved Flights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20
20
21
21
22
22
Sharing Flight Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Share Flight Info – Device to Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
What is Shared – Device to Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Share a Route – App to App . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Import a Route from a Flight-Planning System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sharing a Route with Aspen Avionics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loading a Route from Aspen Avionics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23
25
25
26
26
27
Viewing Enroute Map Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
View High and Low IFR Enroute Themes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Search for Enroute Map Objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
About Search Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Refine Enroute Search Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
View Map Object Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Navaids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Airspace Fixes - Intersection Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Airport Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FIR and UIR Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Distances Between VORs, Changeover Points, and Signal Gaps . . . . . . . . . . . . . . . . . .
CTA DME Step Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
30
30
31
32
33
33
SID and STAR Transition Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
View Ownship on the Enroute Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
View Present Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
View North Up or Track Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Show and Hide Enroute Map Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
34
34
34
35
35
Hide the Legend for Terrain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
View Distance Calculations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Determine Distance with the Offset Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
View Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
View Enroute Weather . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
About Enroute Weather Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
Contents
Surface Observations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Icing, Turbulence, and Winds Aloft Forecasts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
RADAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Accessing Terminal Chart Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Terminal Charts View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Access Terminal Charts for the Active Flight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
About Terminal Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Select Terminal Charts for the Active Flight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Navigate Between Selected Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Highlight a Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Rotate a Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Display Ownship on Approach Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Viewing the Off-Map Indicator on Approach Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Display Ownship on the Airport Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic Display of the Taxi Diagram Upon Landing . . . . . . . . . . . . . . . . . . . . .
View Terminal Weather . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Print a Terminal Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Access Charts for Airports Not Associated with the Active Flight . . . . . . . . . . . . .
Toolbar Common Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mobile FliteDeck Toolbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
45
46
46
47
47
48
48
View Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
View Change Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjust Brightness and Night Theme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Identify GPS Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lock the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
48
49
50
51
51
Data Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Perform an Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
About Data Currency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Switch Between Two Available Enroute Database Versions . . . . . . . . . . . . . . . . . . . . . 54
Switch Between Two Available Terminal Chart Versions . . . . . . . . . . . . . . . . . . . . . . . . 54
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
Introduction
This document provides detailed instructions for using Jeppesen
Mobile FliteDeck version 2.6.1.
About This Document
Intended Audience
The intended audiences for the Jeppesen Mobile FliteDeck User
Guide are pilots and support specialists who may be new to the
application.
Additional References
In addition to this User Guide, Jeppesen provides detailed, taskoriented user training and documentation for Mobile FliteDeck on the
web at the Jeppesen Mobile FliteDeck Training and Documentation
page.
Additional support materials include:
• Jeppesen Mobile FliteDeck Release Notes
• Jeppesen Mobile FliteDeck Online Lesson
• Jeppesen Mobile FliteDeck In-app Help (accessed from
within the Mobile FliteDeck application)
Introduction
Technical Support
Technical Support
Jeppesen provides technical support 24 hours a day, 7 days a
week at:
• United States Toll Free: 800-978-9186
• United States Direct: 303-328-6175
• International: +49-6102-508290
• Email: techsupport@jeppesen.com
• Web: ww1.jeppesen.com/support/technical-support.jsp
Release Summary
Jeppesen iOS applications are continually modified to be fully
compatible with the latest Apple iOS operating system and iOS
devices.
Release Identification Information
This User Guide supports Jeppesen Mobile FliteDeck version
2.6.1.
Operating System Requirements
The minimum operating system requirement is iOS 7.0. This
release has been tested with, and conforms to, iOS 8.1.
Hardware Supported
Jeppesen Mobile FliteDeck is supported on all iPads except the
first generation iPad.
Jeppesen has tested Mobile FliteDeck for compatibility with the
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
2
Introduction
Release Summary
following iOS devices:
Table 1-1
Model
Operating System
iPad 2(Wi-Fi and 3G)
7.1.2, 8.1
iPad 3 (Wi-Fi and 3G)
7.1.2, 8.1
iPad 4
7.1.2, 8.1
iPad Mini
7.1.2, 8.1
iPad Air
7.1.2, 8.1
Connectivity Considerations
Mobile FliteDeck requires a reliable Wi-Fi or cellular Internet
connection to download data updates. The time necessary to
download and perform updates depends on the speed of the
Internet connection and the size of the data coverage area.
Upgrade and Deployment Considerations
Jeppesen Mobile FliteDeck is released through available Apple
distribution models. Only one version of the app can be
downloaded to the iPad at one time.
When you update the Mobile FliteDeck app from one version to
another, the following information is preserved:
• Customized global settings under user control, including
registration and account info
• Saved flights
• User waypoints that are part of a route
NOTE There are special considerations associated with
updating from Jeppesen Mobile FliteDeck 2.1.
October 2014
Jeppesen Mobile FliteDeck User Guide
Copyright © 2014 Jeppesen. All rights reserved.
3
Introduction
Release Summary
When you update from Mobile FliteDeck version 2.1:
• New cultural, terrain, and enroute datasets download. The
size of this download is approximately 500MB.
• Ensure that you have the necessary time and bandwidth to
perform the complete update before commencing the
update.
To prevent Jeppesen Mobile FliteDeck from automatically
downloading in the background and forcing an update at an
inopportune time, disable background updates at the device level.
To disable this function:
1. Tap iPad Settings from the iPad home screen.
2. Tap iTunes & App Store.
3. Under Automatic Downloads, switch Apps to OFF.
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
4
Introduction
Basic iPad Gestures
Getting Started
Mobile FliteDeck enables you to enhance situational awareness
using basic iPad gestures.
Basic iPad Gestures
Pinch to Zoom
Zoom in and out of the display by moving your thumb and finger
in a pinching gesture.
Touch, Hold, then Release
When interacting with the enroute map, you can touch, hold, and
then release any object on the map to add it to your route, delete it
from your route, or view more information about it.
Double-tap to Zoom Out
Double-tap one finger to zoom out to the full extent of your route
(in Enroute view) or to the full extent of the chart (in Terminal
Charts view).
Two-finger Swipe to Navigate
Swipe two fingers to flip through your selected terminal charts,
like flipping through pages in a book.
Four-finger Swipe Between Open Apps
Swipe four fingers to move back and forth between one open app
and another. For example, you can do this gesture to navigate
back and forth between an open PDF reader and Jeppesen Mobile
FliteDeck.
October 2014
Jeppesen Mobile FliteDeck User Guide
Copyright © 2014 Jeppesen. All rights reserved.
5
Introduction
Global Settings
Four- finger Swipe Up and Down
Swipe four fingers up and down to show and hide the iPad
taskbar. This gesture is helpful when you want to go back and
forth between global settings and Jeppesen Mobile FliteDeck.
Global Settings
To adjust Jeppesen Mobile FliteDeck global settings:
• Tap Settings on your iPad Home screen.
• From the list of application settings, tap JeppFD.
Sleep Mode
Switch Sleep Mode to OFF to ensure that the iPad stays powered
on during flight. The setting is ON by default.
NOTE Switching Sleep Mode to OFF reduces the iPad
battery life.
Flight Info - Allow Flight Sharing
To share flight information between two iPads actively running
Jeppesen Mobile FliteDeck, ensure that Allow Flight Sharing is
set to ON. The setting is ON by default.
To share flight information, ensure that both iPads:
• Are actively running Jeppesen Mobile FliteDeck.
• Have Allow Flight Sharing set to ON.
• Have established a connection via Wi-Fi or Bluetooth.
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
6
Introduction
Global Settings
Enroute View
These settings control the display of the Enroute view. Both
Enroute View settings are set to ON by default.
• To be able to track your aircraft, recenter the enroute map
over your aircraft location, and view the enroute map in a
track up orientation, ensure that Enable Moving Map is set
to ON.
• To display ownship position on the enroute map, ensure
that Display Ownship on Enroute is set to ON.
NOTE The minimum GPS accuracy requirement to display
ownship on an enroute map is 200 meters.
Centering the map over aircraft location and displaying the
ownship position on the enroute map are both designed to
improve situational awareness during enroute flight. This
function is not to be used as the basis for navigation.
October 2014
Jeppesen Mobile FliteDeck User Guide
Copyright © 2014 Jeppesen. All rights reserved.
7
Introduction
Global Settings
Terminal Charts View
These settings control the display of the Terminal Charts view.
Both Terminal Charts View settings are set to ON by default.
• To display ownship position on approach charts, ensure that
Display Ownship on Approach is set to ON. This setting
also enables the display of the off-map indicator on
approach charts.
NOTE The minimum GPS accuracy requirement to display
ownship on an approach chart is 50 meters.
• To display ownship position on airport diagrams, ensure
Display Ownship on Airport Diagram is set to ON.
NOTE The minimum GPS accuracy requirement to display
ownship on a taxi diagram is 17 meters.
• The Default Chart Zoom Level is the zoom level
preference for viewing terminal charts. Values are Fit Full
Chart and Fit to Width. Fit Full Chart is the default
value.
• Arpt Diagram (10-9) Speed Threshold is the speed at
which, if enabled, the automatic switch to a taxi diagram
occurs. It is also the speed threshold at which the ownship
appears on the airport diagram. To optimize this setting for
your aircraft, adjust the threshold speed. Values range from
30 to 80 knots.The setting is 40 knots by default.
Note that a GPS signal is required for the automatic switch
to a taxi diagram.
NOTE Displaying the ownship position symbol on the airport
diagram is designed to assist flight crews in orienting
themselves on the airport surface and improving pilot positional
awareness during taxi operations. This function is not to be
used as the basis for ground maneuvering and is limited to
ground operations.
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
8
Introduction
Global Settings
Weather
These settings control your view of weather information.
Weather data is provided by Jeppesen weather services and is
obtained from either the National Weather Service or the UK
Meteorological Office.
• To view weather data overlaid on the enroute map, switch
Display Enroute Wx to ON. This setting is OFF by
default.
• To view terminal weather from the Terminal Charts view,
or from an Airport popover accessed from the enroute map,
ensure that Display METAR/TAF weather is set to ON.
This setting is ON by default.
• Temperature Unit options are Fahrenheit (default) or
Celsius.
• Default METAR/TAF Format options are Raw (default)
and Decoded.
October 2014
Jeppesen Mobile FliteDeck User Guide
Copyright © 2014 Jeppesen. All rights reserved.
9
Introduction
Global Settings
Account Info
Account Info includes the version and build number and available
services for the Jeppesen Mobile FliteDeck application in use.
• Terminal Charts Coverage Code displays your terminal
charts coverage code and is used as a reference for technical
support.
• Site Key displays the site key for the Mobile FliteDeck
application in use.
• Registration displays the serial number for the Mobile
FliteDeck application in use.
• Services includes options to enter credentials so that you
can import flight plans, access company-uploaded
documents, and share routes with Aspen Avionics.
• Flight Plans: Enter the user name, password and URL for
the flight-planning system from which you receive flight
plans.
• Company Manuals: Enter account information so that you
can access company-uploaded documents.
• Switch Allow Aspen Avionics Connection to ON to share
flight information with Aspen Avionics.
Support Information and Settings
These settings provide access to support and application settings.
• Jeppesen Support displays contact information for
technical support. United Sates toll free, direct, and
international numbers are provided, as are email and
Internet addresses. In addition, there is a Send log files via
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
10
Setting Up Your Flight
Global Settings
Email option. This option enables you to email log files
from your iPad to Jeppesen to assist in providing technical
support.
• Terms & Conditions displays links to both the current
Application and Data Terms and Conditions.
• Reset User Settings enables you to restore all Jeppesen
Mobile FliteDeck settings to their default values. This
action does not release the Site Key. To reset user settings:
1. Switch Reset User Settings to ON.
2. Launch Jeppesen Mobile FliteDeck.
3. Tap Proceed to confirm.
• Deactivate enables you to remove all Jeppesen data and
clear the activation information from the iPad. This action
releases the Site Key. To deactivate Jeppesen Mobile
FliteDeck
1. Switch Deactivate to ON.
2. Launch Jeppesen Mobile FliteDeck.
3. Tap Proceed to confirm.
Setting Up Your Flight
The Mobile FliteDeck interface makes it easy to access the
functions and information that you use most.
October 2014
Jeppesen Mobile FliteDeck User Guide
Copyright © 2014 Jeppesen. All rights reserved.
11
Setting Up Your Flight
Overview
Overview
The Flight Info Drawer
The Flight Info drawer is where you create, load, view, and save
the active flight from either the Terminal Charts view or the
Enroute view.
To open and close the expandable Flight Info drawer, tap the
drawer tab.
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
12
Setting Up Your Flight
Create a New Flight
The Active Flight
The active flight is the displayed flight. It includes origin,
destination, any alternate airports, and the route description. The
active flight also includes any selected terminal charts associated
with the flight. The name of the active flight appears on the Flight
Info drawer tab.
The Views
To view the active flight with respect to either the enroute or
terminal air structures:
• Tap the Enroute view button
to access the enroute map.
• Tap the Terminal Charts view button
to access terminal charts.
Create a New Flight
Enter Airports
To create a new flight:
1. Open the Flight Info drawer.
2. Tap the New Flight button.
3. Tap in each field and enter the origin, destination, and any
alternate airports for the new flight.
• Identify airports by using either their city names or airport
ICAO or IATA identifiers.
• Separate alternate airports with a space.
October 2014
Jeppesen Mobile FliteDeck User Guide
Copyright © 2014 Jeppesen. All rights reserved.
13
Setting Up Your Flight
Create a New Flight
Enter Route Points
To add navaids, waypoints, and airways to your route:
1. Tap in the route description box and enter route points.
• Use either the keyboard or copy and paste to enter routes.
• Airports that are entered as points in the route description
are automatically included in the route airports list.
2. Tap Done on the keyboard when you finish entering flight
information.
3. Tap the Flight Info drawer tab to close the drawer.
Both plain language and dot-notation formats are supported in the
route description. For example:
• N37 56.6 W122 21.4 SAC V23 RBL (plain language)
• N37.56.6.W122.21.4.SAC.V23.RBL (dot-notation)
NOTE Dot-notation uses two dots to indicate direct-to points;
and one dot between via routings.
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
14
Setting Up Your Flight
Create a New Flight
About Latitude and Longitude Coordinate Formats
The following latitude and longitude coordinate formats are
supported in the route description:
• NxxWxxx (N37W122)
• Nxx.x Wxxx.x (N37.5 W122.2)
• Nxx xx.x Wxxx xx.x (N37 56.6 W122 21.4)
• Nxx xx.xx Wxxx xx.xx (N37 56.60 W122 21.40)
• NxxxWxxxx (N375W1222)
• N xx xx W xxx xx (N 37 56 W 122 40)
• XXXXN (5275N)
• XXNXX (75N70)
• XXNXXXW(37N122W)
Add SIDs and STARs
After you enter origin and destination airports, you can enter a
SID or a STAR (or both) in the route description.
To render SID or STAR transition points on the enroute map use
this format:
• For a SID, enter: rwy.SID.transition
• For a STAR, enter: transition.STAR.rwy
For example, to enter the LBSTA Three RNAV departure out of
KBOS, departing on Runway 22L, via the LBSTA enroute
transition, you would enter: 22L.LBSTA3.LBSTA
October 2014
Jeppesen Mobile FliteDeck User Guide
Copyright © 2014 Jeppesen. All rights reserved.
15
Setting Up Your Flight
Create a New Flight
When the runway is a part of the route description, transition
points are depicted on the enroute map by a dashed line and a
label that identifies the procedure appears along the dashed line.
In addition, Mobile FliteDeck adjusts the flight distance that
appears in the Flight Info drawer.
NOTE The depiction of SID and STAR transition points on the
enroute map is provided to support situational awareness only.
Always brief the SID or STAR terminal procedure.
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
16
Setting Up Your Flight
Edit Your Route in the Flight Info Drawer
Editing Your Route
There are several ways you can edit your route. You can edit a
route from inside the Flight Info drawer or by simply interacting
with the enroute map itself.
Edit Your Route in the Flight Info Drawer
You can edit your route from within the Flight Info drawer in
either the Enroute view or Terminal Charts view.
To edit your route:
1. Open the Flight Info drawer.
• Tap in the origin, destination, and any alternate airport
fields to add or delete airports.
• Tap in the route description box to add or delete any
navaids, waypoints, or airways.
2. Tap Done on the keyboard.
3. Tap the Flight Info drawer tab to close the drawer.
Edit Your Route by Interacting with the Map
To edit your route by interacting with the enroute map:
1. Touch, hold, and release an airport, navaid, or waypoint
along your intended route.
Mobile FliteDeck displays additional information for that
object.
2. Depending on the type of object, you can review additional
information, or select the object to add it to, or remove it
from, your route.
NOTE The Direct To option is available when the Enable
Moving Map setting in JeppFD global settings is enabled and
the minimum GPS accuracy requirement is met.
October 2014
Jeppesen Mobile FliteDeck User Guide
Copyright © 2014 Jeppesen. All rights reserved.
17
Setting Up Your Flight
Edit Your Route by Interacting with the Map
Edit Your Route with Rubber-Band Routing
To edit your route by using rubber-band routing:
1. Touch a point along the existing route line and drag your
finger to the point that you want to add to the route.
2. After you release your finger, select the action that you
want to perform.
Name and Save a User Waypoint
You can name, add comments to, save and search for user
waypoints. To create and name a user waypoint:
1. Touch, hold, and release the enroute map in the area where
you want to insert a waypoint.
Mobile FliteDeck places a waypoint on the map and
displays the New Waypoint popover.
2. Tap Save Waypoint.
• Tap in the Name field and enter a name for the waypoint.
NOTE Waypoint names can include spaces, but cannot
include any special characters. For example, do not use any of
these characters:
: ] [ ? / < ~ # ` ! @ $ % ^ & * ( ) + = } | : " ; ' , > {.
• To enter comments, tap in the Comments field and enter
any comments that you want to associate with the waypoint.
3. Tap the Done button at the top of the popover when you
finish.
4. Tap Add to Route or, if available, Direct To.
NOTE User waypoints that are part of a route can be shared
between devices and are available in all enroute themes and
zoom scales.
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
18
Setting Up Your Flight
Edit Your Route by Interacting with the Map
Delete a User Waypoint
To delete a user waypoint:
1. Touch, hold, and release the user waypoint that you want to
delete.
Jeppesen Mobile FliteDeck displays the user waypoint
popover.
2. Tap the delete (Trashcan) button at the top of the popover.
3. Tap Delete Waypoint.
Add a Radial DME Point to Your Route
To add a radial DME point to the active flight:
1. Open the Flight Info drawer and enter the radial DME point
to fly to in the route description.
For example, assume that ATC has instructed you to fly
"direct to 26 DME on 156 radial off of falcon VOR.”
In this example, you enter: FQF156/26.
2. Tap Done on the keyboard.
3. Tap the Flight Info drawer tab to close the drawer.
NOTE Touch, hold, and release the newly added radial DME
point to display the popover and, if available, tap Direct To.
Flying Direct To will remove all route points between the
current aircraft position and the DME point.
October 2014
Jeppesen Mobile FliteDeck User Guide
Copyright © 2014 Jeppesen. All rights reserved.
19
Setting Up Your Flight
Edit Your Route by Interacting with the Map
Working with Saved Flights
A saved flight includes origin, destination, alternate airports, and
the route description, including any user waypoints that are a part
of the route. It also includes any selected terminal charts that are
associated with the flight.
Save the Active Flight
To save the active flight:
1. Open the Flight Info drawer.
2. Tap the Save button at the top of the Flight Info drawer.
Each time that you save a flight, it is added to the Saved Flights
list.
View Saved Flights
To view saved flights:
1. Open the Flight Info drawer.
2. Tap the Saved Flights button at the bottom of the drawer.
3. Tap a saved flight from the list of saved flights to expand its
view.
Mobile FliteDeck indicates any selected charts associated
with the flight, as well as the date that the flight was last
updated.
4. Tap the saved flight again to collapse the view.
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
20
Setting Up Your Flight
Edit Your Route by Interacting with the Map
Load a Saved Flight
To load a saved flight:
1. Open the Flight Info drawer.
2. Tap the Saved Flights button at the bottom of the drawer.
3. Tap a saved flight from the list of saved flights to expand its
view.
4. Tap the Load button.
Mobile FliteDeck loads the flight information and the flight
becomes the active flight.
5. Tap the Flight Info drawer tab to close the drawer.
Sort Saved Flights
To sort saved flights:
1. Open the Flight Info drawer.
2. Tap the Saved Flights button at the bottom of the drawer.
3. Tap either Sort by Date or Sort by Name to select a sorting
option.
October 2014
Jeppesen Mobile FliteDeck User Guide
Copyright © 2014 Jeppesen. All rights reserved.
21
Setting Up Your Flight
Edit Your Route by Interacting with the Map
Duplicate a Saved Flight
There may be a situation in which you would want to consider or
plan for two different scenarios for the same airport pair. To do
so, first create the flight, select your charts, and save the flight.
Then, duplicate the saved flight and make any changes to the
duplicated flight.
To duplicate a saved flight:
1. Open the Flight Info drawer.
2. Tap the Saved Flights button at the bottom of the drawer.
3. Tap the Edit button, and then tap the check mark circle next
to the flight that you want to duplicate.
4. Tap the Duplicate (plus sign) button.
Delete Saved Flights
To delete a saved flight:
1. Open the Flight Info drawer.
1. Tap the Saved Flights button at the bottom of the drawer.
2. Tap the Edit button, and then tap the check mark circle next
to the flight that you want to delete.
3. Tap the delete (Trashcan) button.
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
22
Setting Up Your Flight
Edit Your Route by Interacting with the Map
Sharing Flight Information
Sharing flight information enables a more efficient collaboration
between crew members.
Share Flight Info – Device to Device
NOTE To share flight information between two iPads actively
running Mobile FliteDeck, first ensure that the Allow Flight
Sharing setting in JeppFD global settings for both iPads is set
to ON. In addition, ensure that either a Wi-Fi or Bluetooth
connection has been established for both iPads.
To share an active flight:
1. Open the Flight Info drawer.
2. Tap the Share button at the top of the drawer.
3. From the list of nearby iPads, select the iPad with which
you want to share.
To share a saved flight (without loading it):
1. Open the Flight Info drawer.
2. Tap the Saved Flights button at the bottom of the drawer.
3. Tap a saved flight to expand its view.
4. Tap the Share button for the selected flight.
5. From the list of nearby iPads, select the iPad with which
you want to share.
October 2014
Jeppesen Mobile FliteDeck User Guide
Copyright © 2014 Jeppesen. All rights reserved.
23
Setting Up Your Flight
Edit Your Route by Interacting with the Map
Jeppesen Mobile FliteDeck displays a notification on the
receiving iPad that you would like to share flight information.
The recipient chooses to Load, Save, or Decline.
The sending iPad then displays Shared or Declined, depending on
the action the recipient chooses.
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
24
Setting Up Your Flight
Edit Your Route by Interacting with the Map
What is Shared – Device to Device
When you share flight information from one iPad to another iPad
running Jeppesen Mobile FliteDeck, the following is shared:
• Origin, destination, and any alternate airports
• Navaids, waypoints, (including user waypoints), and
airways entered into the route description
• Selected terminal charts for the flight
NOTE Both devices must include the terminal chart coverage
area of the selected terminal chart to successfully share the
selected chart.
When you share flight information from one iPad to another iPad
running Jeppesen Mobile FliteDeck, the following is NOT
shared:
• Highlights on terminal charts
• Rotated view of terminal charts
• Comments that are associated with a user waypoint
Share a Route – App to App
To share a route from a flight-planning app on your iPad that is
configured to share with Jeppesen Mobile FliteDeck:
1. Load the route in the flight-planning app.
2. Select the option to share with Jeppesen Mobile FliteDeck.
Jeppesen Mobile FliteDeck opens and displays a
notification that an app would like to share a flight and
displays these options: Load, Save, or Decline.
3. Tapping Load loads the route as the active flight.
4. Tapping Save adds the route to the list of Mobile FliteDeck
saved flights.
October 2014
Jeppesen Mobile FliteDeck User Guide
Copyright © 2014 Jeppesen. All rights reserved.
25
Setting Up Your Flight
Edit Your Route by Interacting with the Map
Import a Route from a Flight-Planning
System
NOTE To import a route from a flight-planning system that is
configured to deliver flight plans to Jeppesen Mobile FliteDeck,
first enter your flight-planning system credentials in JeppFD
global settings > Services > Flight Plans.
Once your flight-planning system credentials are entered:
1. Open the Flight Info drawer.
2. Tap the Flight Plans button to expand the view.
The most recently retrieved flight plans appear.
•
If any updates have become available since the last time
that you accessed the flight plans, FliteDeck displays
the New Updates Available button.
•
Tap the New Updates Available button to update the
list of flight plans.
3. Tap a flight plan to select it.
4. Tap either the Load button or the Save button for the
selected flight.
Sharing a Route with Aspen Avionics
To share a loaded flight from Jeppesen Mobile FliteDeck to
Aspen Avionics, first ensure that the iPad is connected to the
AspenCG100 Wi-Fi and that Allow Aspen Avionics
Connection in JeppFD global settings is set to ON.
Once a connection has been established:
1. Open the Flight Info drawer.
2. Tap the Aspen button at the top of the drawer.
3. Tap Share Route.
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
26
Viewing Enroute Map Information
View High and Low IFR Enroute Themes
After the route is successfully shared, go to the Aspen MFD
Gateway window and select GPS1. The shared route moves to
the Garmin GPS device. The Aspen Avionics device accepts all
valid route points.
Loading a Route from Aspen Avionics
To share a route that is activated in Aspen Avionics to Jeppesen
Mobile FliteDeck, first ensure that the iPad is connected to the
AspenCG100 Wi-Fi and that Allow Aspen Avionics
Connection in JeppFD global settings is set to ON.
Once a connection has been established:
1. Open the Flight Info drawer.
2. Tap the Aspen button at the top of the drawer.
3. Tap Load Route.
Viewing Enroute Map Information
Jeppesen Mobile FliteDeck helps you increase situational
awareness by viewing your flight with respect to the enroute and
terminal air structures. This section describes available enroute
map information.
View High and Low IFR Enroute Themes
To switch between High IFR and Low IFR enroute themes:
1. Tap the Enroute Theme button.
2. Select your preferred enroute theme.
October 2014
Jeppesen Mobile FliteDeck User Guide
Copyright © 2014 Jeppesen. All rights reserved.
27
Viewing Enroute Map Information
Search for Enroute Map Objects
Search for Enroute Map Objects
To search for an enroute map object:
1. From the Enroute view, tap the Search button on the
toolbar.
NOTE To clear a search query, tap the X in the top right of the
search field.
2. Enter the city name, object name, or airport ICAO or IATA
identifier in the search field.
Jeppesen Mobile FliteDeck searches include searches for
named user waypoints and searches across multiple words,
that is, searches include not just the first word in the name.
3. Tap the Search Results button or tap Done on the keyboard
to display the search results.
• The number of search results appears on the Search
Results button.
• Search results appear in the viewable area on the enroute
map and in the list of results available from the Search
Results button.
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
28
Viewing Enroute Map Information
Search for Enroute Map Objects
4. Select a search result to view the details popover.
5. You can review more information about the object by
tapping any flyout ( > ), or you can add the object to your
route.
About Search Results
Mobile FliteDeck searches across multiple words, not just the
first word in the name.
Search results are:
• Not limited by the map view. You can pan the map or zoom
out to see search results outside the current map view.
• Displayed in the search results list and ordered by distance
either from the map center or from your aircraft position.
You can scroll the list to see the name and distance of
objects that are farther away.
• Returned across enroute themes (High IFR and Low IFR).
• Not limited to filtered objects.
October 2014
Jeppesen Mobile FliteDeck User Guide
Copyright © 2014 Jeppesen. All rights reserved.
29
Viewing Enroute Map Information
View Map Object Details
Refine Enroute Search Results
To refine enroute search results, tap the APT or FIX button at the
top of the search results list. For example, to view only airports in
the search results, tap APT. To view only fixes in the search
results, tap FIX.
View Map Object Details
Navaids
To view enroute map details, including navaids:
1. Touch, hold, and release the object on the map.
The selected object is highlighted and an object detail
popover appears.
2. Depending on the type of object and its position on the map,
you can review additional information for it, or choose from
a list of additional objects.
3. Tap away from the popover to dismiss it.
Airspace Fixes - Intersection Info
Intersection information is available when an enroute fix is
included in the route description or when the Waypoints filter is
set to show on the enroute map.
To display intersection information:
1. Touch, hold, and release an enroute fix. The Enroute Fix
popover appears.
2. Tap Usage for usage information.
3. Tap Intersection Info for a detailed view of the intersection
formation.
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
30
Viewing Enroute Map Information
View Map Object Details
Airport Information
In addition to general airport information, the Airport popover
includes runway, communication, and access to weather
information.
To view airport information from the enroute map:
1. Touch, hold, and release the airport to display the airport
popover.
• Tap Runways to view the size and surface of runways at
the airport. Reciprocal airport runways are grouped together
with information organized by chart. Tap a specific runway
to view more information, such as displaced threshold,
lighting, and TDZ elevation.
• Tap Communication to view airport communication
information grouped by type. When more than two of a
given type are available, the first two are provided. To
display more frequencies, tap the More button.
• Tap Wx to view METAR/TAF information at that airport.
2. Tap away from the popover to dismiss it.
Note that airports are filtered by runway length in the Enroute
view and are automatically based on zoom scale. For example:
In High IFR theme:
• 160nm/in - IFR airports with Runways >10000 feet
• 80nm/in - IFR airports with Runways >8000 feet
• 40nm/in - IFR airports with Runways >5000 feet
• 5nm/in - All IFR airports
In Low IFR theme:
• 80nm/in - IFR airports with Runways >8000 feet
• 40nm/in - IFR airports with Runways >5000 feet
• 5nm/in - All IFR airports
• 2.5nm/in - All IFR and VFR airports
October 2014
Jeppesen Mobile FliteDeck User Guide
Copyright © 2014 Jeppesen. All rights reserved.
31
Viewing Enroute Map Information
View Map Object Details
FIR and UIR Information
To view FIR or UIR information from the Enroute view:
1. Touch, hold and release a FIR or UIR boundary.
In addition to upper and lower limits, the FIR and UIR
popover includes communication information, cruise
information, and notes, as applicable
• Tap Communication to view communication frequencies
grouped by type. When more than two of a given type are
available, the first two are provided. To display more
frequencies, tap the More button.
• Tap Cruise to view the cruise tables.
• Tap Notes, indicated visually on the enroute map by blue
"i" icons, to review operational notes associated with the
boundary.
2. Tap away from the popover to dismiss it.
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
32
Viewing Enroute Map Information
View Map Object Details
Distances Between VORs, Changeover
Points, and Signal Gaps
Distances between VORs, changeover points, and signal gaps
appear on the enroute map when an airway is part of the route
description or when the Airways filter is set to show airways on
the enroute map.
.
CTA DME Step Values
CTA DME step values appear around airports in Australia and
New Zealand when Airspace is set to show on the enroute map.
To view CTA information, touch, hold, and release the CTA
boundary. From the CTA popover, you may need to select a
specific CTA to review its information.
October 2014
Jeppesen Mobile FliteDeck User Guide
Copyright © 2014 Jeppesen. All rights reserved.
33
Viewing Enroute Map Information
SID and STAR Transition Points
SID and STAR Transition Points
When the runway is a part of the route description, a dashed line
depicts the transition points of the SID and/or STAR on the
enroute map. A label that identifies the procedure appears along
the dashed line. In addition, Mobile FliteDeck adjusts the flight
distance that appears in the Flight Info drawer.
To render SID or STAR transition points on the enroute map use
this format:
• For a SID, enter: rwy.SID.transition
• For a STAR, enter: transition.STAR.rwy
View Ownship on the Enroute Map
The current aircraft position is available on the enroute map
when:
• Enable Moving Map and Display Ownship on Enroute in
JeppFD global settings are set to ON.
• The minimum GPS accuracy requirement is met.
NOTE The minimum required GPS accuracy to display
ownship on the enroute map is 200 meters.
View Present Position
To recenter the map over your aircraft position after you have
panned away, tap the Present Position button.
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
34
Viewing Enroute Map Information
View North Up or Track Up
The Present Position button is available in the Enroute view
when:
• Enable Moving Map in JeppFD global settings is set to
ON.
• The minimum required GPS accuracy to display ownship
on the enroute map is met.
NOTE The minimum required GPS accuracy to display
ownship on the enroute map is 200 meters.
View North Up or Track Up
To change the enroute map orientation, tap the North Up or
Track Up button.
NOTE To change the orientation to Track Up, Enable Moving
Map in JeppFD global settings must be set to ON.
Show and Hide Enroute Map Features
To toggle between showing (ON) and hiding (OFF) airports,
airways, waypoints, navaids, airspace, and terrain on the enroute
map, tap any of the filter buttons on the right side of the Enroute
view.
Depending on the zoom level, certain enroute map features are
automatically filtered to declutter the map.
Hide the Legend for Terrain
To hide the terrain legend that appears on the enroute map when
Terrain is showing, tap the Settings button on the Jeppesen
Mobile FliteDeck toolbar, and then switch Terrain Legend to
OFF.
October 2014
Jeppesen Mobile FliteDeck User Guide
Copyright © 2014 Jeppesen. All rights reserved.
35
Viewing Enroute Map Information
View Notes
View Distance Calculations
Mobile FliteDeck displays a set of range rings or arcs that provide
awareness of your distance to objects on the map at a glance.
To show and hide the range rings, tap the Range Rings button.
As you zoom in or out, the range rings change with the map
scale.The center-most ring includes a compass rose that indicates
true north, south, east, and west.
Determine Distance with the Offset
Indicator
To determine the distance and direction from your aircraft to any
other object on the map:
1. Tap the Range Rings button to show the range rings.
2. Pan the map so that the map object in question is in the
center of the inner range ring.
A magenta offset indicator appears, showing distance and
direction to your aircraft position.
NOTE Enabling Moving Map in JeppFD global settings must
be set to ON to determine distance and direction from your
aircraft. Also, if you toggle range rings OFF, the offset indicator
no longer appears.
View Notes
To access notes along your route:
1. Tap the Notes button.
2. Select the type of note that you want to view.
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
36
Viewing Enroute Map Information
View Enroute Weather
3. Tap the desired note.
Mobile FliteDeck highlights the object on the map to which
the note applies.
NOTE Notes are based on your current view, and the zoom
level must be 100 NM or less to access them.
All of the notes provided on pre-composed paper charts are
available:
• Operational: Tactically important information regarding
specific navigation elements. These notes are equivalent to
Ball Flag notes on paper charts and are indicated visually on
the enroute map by blue "i" icons. You can also access
operational notes directly from the enroute map by tapping,
holding, and then releasing the associated blue “i” icons.
• Regional: Procedures, conditions, or requirements for a
specific geographical region. These notes are equivalent to
Floating notes on paper charts.
• Reference: Aeronautical reference information for large
charted areas. These notes are equivalent to End Panel notes
on paper charts.
View Enroute Weather
Weather data is provided by Jeppesen weather services and is
obtained from either the National Weather Service or the UK
Meteorological Office.
NOTE To receive enroute weather, Display Enroute Wx in
JeppFD global settings must be set to ON and an Internet
connection must be established.
To view enroute weather:
1. Tap the Wx button from the Enroute view.
2. Switch Weather to ON.
3. Tap the weather type that you want to view.
October 2014
Jeppesen Mobile FliteDeck User Guide
Copyright © 2014 Jeppesen. All rights reserved.
37
Viewing Enroute Map Information
View Enroute Weather
Enroute weather includes surface observations, RADAR
(NEXRAD, echo tops, and lightning), and icing, turbulence, and
winds aloft forecasts.
About Enroute Weather Updates
After you establish an Internet connection and switch Weather to
ON, Mobile FliteDeck checks the selected weather type for
updates. Mobile FliteDeck downloads weather data within the
radius of your route or scales data to your coverage ages.
An enroute weather selection boundary displays to indicate the
extent of the weather coverage area.
• If your enroute data coverage is not worldwide, Jeppesen
Mobile FliteDeck downloads weather data only within the
boundaries of your enroute data coverage.
• If your enroute data coverage is worldwide, and a route is
entered, Jeppesen Mobile FliteDeck downloads weather
data only for an area that extends 1,000 NM around your
route (including the beginning and ending points of the
route).
• If your enroute data coverage is worldwide, but no route is
entered, Jeppesen Mobile FliteDeck downloads weather
data for the selected weather type for the entire worldwide
coverage.
Weather information for the selected weather type is
automatically checked every six minutes. At this interval, only
weather that has been updated on the Jeppesen Weather server is
updated on your iPad.
You can also manually update a selected weather type by tapping
the Reload button at the bottom of the Weather popover.
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
38
Viewing Enroute Map Information
View Enroute Weather
Surface Observations
To view surface observations:
1. Tap the Weather button.
2. Switch Weather to ON.
3. Tap the Surface Observations button.
4. Tap away from the Weather popover to dismiss it and view
the weather overlaid on the map.
Icing, Turbulence, and Winds Aloft
Forecasts
To view icing, turbulence, or winds aloft forecasts:
1. Tap the Weather button.
2. Switch Weather to ON, tap the Icing, Turbulence, or
Winds Aloft button.
3. Tap the altitude at which you want to view the forecast
weather.
4. Tap away from the Weather popover to dismiss it and view
the weather overlaid on the map.
You can display up to four weather forecast images.
To change to a different forecast period after you select the
weather type, tap the Forecast button and then select a different
forecast time.
RADAR
To view NEXRAD, echo tops, or lightning:
1. Tap the Weather button.
2. Switch Weather to ON, tap the RADAR button.
3. Tap the type of RADAR weather that you want to view.
October 2014
Jeppesen Mobile FliteDeck User Guide
Copyright © 2014 Jeppesen. All rights reserved.
39
Accessing Terminal Chart Information
View Enroute Weather
4. Tap away from the Weather popover to dismiss it and view
the weather overlaid on the map.
5. Tap the Play button to cycle through the series of multiple
images.
NOTE After you tap Play, the animation continues to cycle
through the images until you either tap the Pause button or
deselect the weather type to stop viewing it.
Accessing Terminal Chart Information
You can select multiple charts and navigate between them,
highlight and rotate them all for easy access during critical phases
of flight.
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
40
Accessing Terminal Chart Information
Terminal Charts View
Terminal Charts View
Access Terminal Charts for the Active Flight
By default, the first time that you tap the Terminal Charts view
button from an active flight, the airport diagram for the origin
airport displays.
To view other charts associated with the active flight's origin
airport:
1. Tap a chart type button.
2. Scroll through the list of charts.
To view terminal charts for other airports associated with the
active flight (including alternate airports):
October 2014
Jeppesen Mobile FliteDeck User Guide
Copyright © 2014 Jeppesen. All rights reserved.
41
Accessing Terminal Chart Information
Access Terminal Charts for the Active Flight
1. Tap the Airport button.
2. Select the desired airport from the list of airports in the
active flight.
About Terminal Charts
Terminal charts are organized by chart types. The chart types are:
• REF (Reference): Nonprocedural charts, sorted
alphabetically by title.
• CO (Company): Your company tailored charts. (This chart
type is available only if your company subscribes to
Jeppesen tailored charting services).
• STAR (Standard Terminal Arrival): Arrival charts, sorted
alphabetically by title.
• APP (Approach): Approach charts, grouped by runway and
sorted by index number.
• TAXI: Taxi charts, sorted by index number.
• SID (Standard Instrument Departure): Departure charts,
sorted alphabetically by title.
Select Terminal Charts for the Active Flight
To preview and select charts for the active flight:
1. Tap the Terminal Charts view button.
2. Tap a chart type button and scroll through the list of charts.
3. Tap the desired chart to preview it.
4. Tap the check mark circle next to the chart to select it and
add it to the selected charts bar that appears under the chart
display window.
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
42
Accessing Terminal Chart Information
Highlight a Chart
After you select a chart, whenever you tap that chart type button,
the last viewed, selected chart from that chart type appears. If no
charts are selected within a chart type, the chart list opens.
Navigate Between Selected Charts
Each selected chart is represented by a pagination dot on the
selected charts bar at the bottom of the chart display window. The
chart type label also appear above the dots.
The highlighted dot identifies the chart that is currently displayed
in the series of selected charts.
To navigate between the selected charts, you can:
• Use a two-finger swipe, as though you are turning the pages
of a book.
• Tap outside on the left or right side of the selected charts
bar to move to the previous or next chart.
• Tap the chart type button to jump across multiple selected
charts.
Highlight a Chart
To highlight information on a terminal chart, tap the Highlight
button. In highlight mode, your finger acts as a highlighter on the
chart.
Tap the Highlight button again to exit highlight mode or tap one
of the following buttons:
• Undo button to remove the last highlight.
• Clear All button to clear all highlights.
NOTE Highlights persist on the chart until you remove the
highlights or update the chart.
Highlights do not accompany charts that are shared between
devices.
October 2014
Jeppesen Mobile FliteDeck User Guide
Copyright © 2014 Jeppesen. All rights reserved.
43
Accessing Terminal Chart Information
Rotate a Chart
Rotate a Chart
To rotate a chart, tap the Rotate button. Each time that you tap
the Rotate button, the chart turns 90 degrees clockwise.
NOTE The rotated view does not accompany a chart that is
shared between devices.
Display Ownship on Approach Charts
Mobile FliteDeck displays ownship position on approach charts
when:
• Display Ownship on Approach in JeppFD global settings
is set to ON.
• The minimum required GPS accuracy to display ownship
on approach charts is met.
NOTE The minimum required GPS accuracy to display
ownship on approach charts is 50 meters.
There may be situations when you want to temporarily disable the
ownship from appearing on the approach chart. To do so, tap the
GPS Status button while viewing the approach chart, and switch
Ownship on Approach to OFF.
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
44
Accessing Terminal Chart Information
Display Ownship on the Airport Diagram
Viewing the Off-Map Indicator on Approach
Charts
Mobile FliteDeck provides an off-map indicator as a visual cue as
to the direction from which your aircraft is approaching when:
• Display Ownship on Approach in JeppFD global settings
is set to ON.
• Your aircraft is within 10NM of the approach chart
boundary.
• The minimum required GPS accuracy to display ownship
on approach charts is met.
NOTE The minimum required GPS accuracy to display
ownship on approach charts is 50 meters.
Display Ownship on the Airport Diagram
Mobile FliteDeck displays ownship on the airport diagram when:
• Display Ownship on Airport Diagram is set to ON in
JeppFD global settings.
• Your aircraft is moving no faster than the speed specified in
the Arpt Diagram (10-9) Speed Threshold in JeppFD
global settings. The speed threshold is 40 knots by default.
• The minimum required GPS accuracy to display ownship
on taxi diagrams is met.
NOTE The minimum required GPS accuracy to display
ownship on a Taxi diagram is 17 meters.
October 2014
Jeppesen Mobile FliteDeck User Guide
Copyright © 2014 Jeppesen. All rights reserved.
45
Accessing Terminal Chart Information
Automatic Display of the Taxi Diagram Upon Landing
Automatic Display of the Taxi Diagram Upon Landing
The taxi diagram for the airport at which you are landing
automatically displays in Mobile FliteDeck when:
• Show Taxi On Landing is set to ON from the Settings
button on the Mobile FliteDeck toolbar.
• The minimum required GPS accuracy to display ownship
on taxi diagrams is met.
NOTE The automatic display of a taxi diagram is based on the
speed threshold that is specified for in the Arpt Diagram (10-9)
Speed Threshold in JeppFD global settings. The speed
threshold is 40 knots by default.
View Terminal Weather
Weather data is provided by Jeppesen weather services and is
obtained from either the National Weather Service or the UK
Meteorological Office.
NOTE To receive terminal weather, Display METAR/TAF in
JeppFD global settings must be set to ON and an Internet
connection must be established.
To view METAR or TAF weather data:
• From Terminal Charts view, tap the Wx button.
A Weather popover for the selected airport displays.
If the weather data is expired, a weather warning appears in red in
the same location as the weather age. METAR and TAF updates
occur separately.
To manually update the weather data:
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
46
Accessing Terminal Chart Information
Print a Terminal Chart
• Tap the Reload button at the bottom of the Weather
popover.
• Tap away from the popover to dismiss it.
Print a Terminal Chart
To print the displayed chart to an AirPrint-enabled printer:
1. Tap the Settings button on the Mobile FliteDeck toolbar.
2. Tap Print.
3. Select the printer and the number of copies.
4. Tap the Print button.
NOTE Charts print out one per page and cannot be reformatted.
Access Charts for Airports Not Associated with the
Active Flight
To access terminal charts for an airport not associated with the
active flight:
1. Tap the Airport button.
2. Tap the All Airports button at the bottom of the Airports
popover.
3. Tap in the Search field and enter the city name or airport
ICAO or IATA identifier.
4. Tap the airport name from the results list to select it.
5. Tap a chart type button and scroll through the list of charts
for that airport's chart type.
October 2014
Jeppesen Mobile FliteDeck User Guide
Copyright © 2014 Jeppesen. All rights reserved.
47
Toolbar Common Tasks
Mobile FliteDeck Toolbar
Toolbar Common Tasks
The Mobile FliteDeck toolbar is available to you from all views
and display orientations so that you can easily perform common
tasks.
Mobile FliteDeck Toolbar
View Manuals
NOTE You must have a PDF reader app installed on your
iPad to view manuals.
To view a manual:
1. Tap the Manuals button on the Mobile FliteDeck toolbar.
2. Select the manual that you want to view.
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
48
Toolbar Common Tasks
Mobile FliteDeck Toolbar
3. Select the PDF reader app of your choice.
You can use a four-finger swipe to move between the PDF reader
app and the Jeppesen Mobile FliteDeck app.
NOTE If your company subscribes to Jeppesen Document
Management Services, in addition to the Jeppesen Standard
Airway Manuals, your company documents might also be
available from the Manuals button on the FliteDeck toolbar.
View Change Notices
Change notices are available based on your current view. For
example, in Enroute view, change notices are displayed by
region. In Terminal Charts view, change notices are displayed for
the selected airport.
To view change notices, tap the Manuals button on the Mobile
FliteDeck toolbar, and then tap the Notices button at the bottom
of the Manuals popover.
• From the Terminal Charts view, any available notices for
the selected airport appear in a popover.
• From the Enroute view, select the region for which you
want to view change notices, and then select the PDF reader
app of your choice to view the notices.
NOTE You can access the most recent change notices by
tapping the jeppesen.com link at the bottom of the Change
Notices popover.
On Demand Access to More Recent Change
Notices
You can access more recent change notices by tapping the
jeppesen.com web link at the bottom of the Change Notices
popover. These change notices are updated on a daily basis.
October 2014
Jeppesen Mobile FliteDeck User Guide
Copyright © 2014 Jeppesen. All rights reserved.
49
Toolbar Common Tasks
Mobile FliteDeck Toolbar
To access more recent change notices:
1. Tap the Manuals button.
2. Tap the Notices button at the bottom of the popover.
3. Tap View More Recent Change Notices at jeppesen.com
at the bottom of the popover.
A browser window opens.
• Select your desired output format (Jeppesen or ICAO).
• Select Airports or FIRs.
• Tap in the Search field and enter the airport or FIR
boundary name.
• Tap the Search button.
You can use a four-finger swipe to navigate between the browser
and theJeppesen Mobile FliteDeck app.
NOTE Check NOTAMs and all other pertinent information
prior to flight.
Adjust Brightness and Night Theme
To adjust the display brightness, tap the Brightness button on the
FliteDeck toolbar, and then slide the brightness control to
decrease or increase the display brightness.
To adjust for optimal viewing in low-light conditions, switch the
Night Theme to ON.
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
50
Toolbar Common Tasks
Mobile FliteDeck Toolbar
Identify GPS Status
The GPS Status button appears on the Jeppesen Mobile
FliteDeck toolbar when Enable Moving Map or either one of the
two Display Ownship settings in JeppFD global settings is set to
ON.
Tap the GPS Status button to view the current ground speed,
GPS altitude, last position received, and accuracy status.
A badge appears over the GPS Status button if the GPS signal
does not meet the minimum accuracy requirement. The minimum
required GPS accuracy to display ownship position is:
• 200 meters for the enroute map.
• 50 meters for approach charts.
• 17 meters for an airport diagram.
Lock the Display
To lock and unlock the Jeppesen Mobile FliteDeck display, tap
the Display Lock button on the toolbar.
Locking the display prevents you from accidentally panning or
zooming away from the current display.
When the display is locked, the Display Lock button is
highlighted and you cannot access any other FliteDeck button.
October 2014
Jeppesen Mobile FliteDeck User Guide
Copyright © 2014 Jeppesen. All rights reserved.
51
Toolbar Common Tasks
Perform an Update
Data Updates
Jeppesen Mobile FliteDeck provides a simple and quick way to
verify the status of your enroute, terminal charts, and manuals
data; and if required, perform updates.
Perform an Update
Whenever data updates are available, a badge appears on the
Settings button on the Jeppesen Mobile FliteDeck toolbar. The
badge indicates the number of updates available.
• The badge is amber when data is current, and an update is
available.
• The badge is red when data is not current.
To perform updates:
1. Tap the Settings button.
2. Tap Updates.
3. Tap the Update button.
Download time depends on the quality of your connection to the
Internet and the size of the required updates.
At any time during an update, you can pause the download by
tapping the Pause button at the top of the update status line.
If more than one update is available, Jeppesen Mobile FliteDeck
automatically begins to download the next available update. To
resume downloading after pausing an update, tap the Resume
button at the top of the update status line.
To cancel all updates and exit Updates, tap the X at the top of the
Updates screen. To resume updates after having canceled, tap the
Settings button, tap Updates, and then tap the Resume button.
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
52
Toolbar Common Tasks
About Data Currency
About Data Currency
To view the status of your Enroute, Terminal Chart, and Manual
data, tap the Settings button and then tap Updates on the Mobile
FliteDeck toolbar.
Data is identified as Current or Not Current.
Mobile FliteDeck further displays a bar chart for each of the three
data update cycles. Each bar chart displays the current date for
reference, and current and not current dates for the data.
Update Bar Chart Color Codes
The bar chart color codes are:
• Green, which indicates that current data is in use.
• Amber, which indicates that current data is in use with an
update available.
• Red, which indicates that data is not current.
Update Bar Chart Color Codes When Two
Data Sets Are Available
When two data sets are available, the bar chart color codes are:
• Light green, which indicates that current data is in use.
• Dark green, which indicates that data is available but not in
use.
• Light red, which indicates that data is not current.
• Dark red, which indicates that the next update has not been
downloaded.
October 2014
Jeppesen Mobile FliteDeck User Guide
Copyright © 2014 Jeppesen. All rights reserved.
53
Toolbar Common Tasks
About Data Currency
Switch Between Two Available Enroute
Database Versions
When two enroute databases are available, the effective date of
the database in use appears in the amber tag on the map. To
manually change enroute database versions when more than one
version is available:
1. Tap the Settings button
2. Tap the Updates button.
3. Tap the Switch Back to Data Expiring [date] to view that
database.
4. To return to the current database, tap Switch to Data
Effective [date].
Switch Between Two Available Terminal
Chart Versions
When a terminal chart is revised mid-cycle, the revision date
appears along with an amber tag next to the chart title on the chart
list. To change terminal chart versions when more than one
version is available:
1. Tap the amber tag from the chart list to display the Revision
popover.
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
54
Toolbar Common Tasks
About Data Currency
2. Tap the chart title to view a different version of the chart.
NOTE When a chart does not have an effective date on it, it is
considered effective (usable) upon receipt and Jeppesen
Mobile FliteDeck displays it as soon as you update.
If a chart has an effective date, Jeppesen Mobile FliteDeck
continues to show the current version until 24 hours before its
effective date. Then Jeppesen Mobile FliteDeck enables you to
select either the original version or the newer version. At 24
hours after the effective date, the app shows only the new
version of the chart.
If an approach chart is revised mid-cycle and the runway is
changed, the chart will be listed under a General chart type
category in the Terminal Charts view list.
October 2014
Jeppesen Mobile FliteDeck User Guide
Copyright © 2014 Jeppesen. All rights reserved.
55
Toolbar Common Tasks
About Data Currency
Jeppesen Mobile FliteDeck User Guide
October 2014
Copyright © 2014 Jeppesen. All rights reserved.
56
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising