User Manual (1)

User Manual (1)
Precautions………………………………………………………………………………………….
Safety Tips…………………………………………………………………………………………….
•
•
•
•
•
•
•
•
•
Please read this manual carefully before using the camera.
Avoid damage from stress, violent vibration or liquid intrusion during
transportation, storage or installation.
Take care of the camera during installation to prevent damage to the
camera case, ports, lens or PTZ mechanism.
Do not apply excessive voltage. (Use only the specified voltage.)
Otherwise, you may experience electrical shock.
Keep the camera away from strong electromagnetic sources.
Do not aim the camera at bright light sources (e.g. bright lights, the sun,
etc.) for extended periods of time.
Do not clean the camera with any active chemicals or corrosive detergents.
Do not disassemble the camera or any of the camera's components. If
problems arise, please contact your authorized dealer.
After long term operation, moving components can wear down. Contact
your authorized dealer for repair.
Supplied Accessories…………………………………………………………………………….
•
•
•
•
•
HD Color Video Camera (1)
12V/2.0A DC Power Adapter (1)
Installation Bracket (1)
Installation Screw (1)
USB 3.0 Data Lines (3m), Serial Control Line, RS-232C to RS-485 Cable
Ver 1.1 6/26/14
•
•
IR Remote Controller (1)
User Manual (1)
Rear Board Connectors…………………………………………………………………………
High Definition Interface:
USB 3.0
Control Signal Interface:
Mini DIN-8 (VISCA IN, VISCA OUT/RS485)
Control Signal Configuration:
Dip-Switch Pin 7/TTL Signal; Baud Rate: 9600bps
Power Supply Interface:
DC 12V Socket
Electrical……….…………………………………………………………………………………….
Power Supply Adapter:
12V DC/2A
Input Voltage:
12V DC (10.5-14V DC)
Input Power:
24W (MAX)
Structure……………………………………………………………………………………………….
Material:
Aluminum, Plastic
Dimensions (W x H x D):
9.84 in. (250mm) x 5.51 in. (140mm)
x 6.06 in. (154mm)
Mass:
2.84 lbs. (1.29 kg.)
Working Environment:
Indoor
Operating Temperature:
32ºF to 113ºF
Storage Temperature:
-14ºF to 140ºF
Color:
Silver Gray
Ver 1.1 6/26/14
Rear Board & Function………………………………………………………………………..
1. Front View…………………………………………………………………………………..
1. Lens
20x Optical Zoom.
2. IR Receiver
To receive IR remote controller signal.
3. Power LED
Blue LED blinks when unit is powered.
4. Stand by LED
Orange LED blinks for Stand-By status, Blue LED for Working Status.
5. IR Receiver
To receive IR remote controller signal.
Ver 1.1 6/26/14
2. Rear View………………………………………………………………………………………….
6. Power Switch
Power On/Off button.
7. DC IN 12V Socket
Only use the Power Adapter supplied with this camera.
8. IR Receiver
To receive IR remote controller signals.
9. IR Selective Switch
When using only one remote to control more than one camera, this switch will
assign a unique ID to each camera.
10. VISCA IN Port
For hard wired remote control from a 3rd party PC, joystick, etc...
11. VISCA Out Port/RS485
Ver 1.1 6/26/14
Used for daisy chaining multiple cameras for RS-232 RS-485 control.
12. USB 3.0 Interface
For connection to PC.
2. Bottom View………………………………………………………………………………….
1. Tripod
Will accept 1/4-20 bolt from 3rd party tripod, wall or ceiling mount.
2. Dip-Switch
Used for selecting baud rate and the remote signal output switch.
Ver 1.1 6/26/14
4. Dip-Switch Settings…………………………………………………………………………..
Dip-Switch 1 - (To set communication baud rate).
Dip-Switch 2 - (To set control protocol).
Dip-Switch 3 - (Set only for firmware upgrading).
Dip Switch 4 & 5 - (To set camera’s RS232/RS485 ID number – for daisy chain wired
control).
Ver 1.1 6/26/14
Cable Connection Info…………………………………………………………………………
VISCA RS-232C - IN Reference………………………………………………………………
VISCA RS-232C - Out Reference……………………………………………………………
Ver 1.1 6/26/14
OSD MENU……………………………………………………………………………………………..
On Screen Display Menu - Use the OSD menu to access and change the
camera’s settings.
Note: You cannot manually move the camera (pan/tilt) when the OSD menu is
visible on the screen.
The Dome OSD Menu is as follows:
•
•
•
•
•
•
•
•
Pan Speed
Default Value: 20
Set speed of Pan motor - Range = 1 - 63
Tilt Speed
Default Value: 20
Set speed of Pan motor - Range = 1 – 63
Scan Speed (Auto Pan Mode)
Default Value: 6
Set speed of boundary scan - Range = 1 – 63
Tour Path (uses presets)
Default Value: 1
Select desired tour path - Range = 1 – 4
Tour Dwell
Default Value: 5
Set duration to dwell on each preset - Range = 1 – 60
Proportion
Default Value: On
Set Proportion - Range = On – Off
Auto Rev
Default Value: P
Set camera mounting orientation – N for inverted ceiling mount
Frame
Default Value: 60Hz
Set Refresh Rate - Range = 50Hz or 60 Hz
Ver 1.1 6/26/14
The Lens OSD Menu is as follows:
•
•
•
•
WDR
Wide Dynamic Range = On or Off
Default Value: Off
BACKLIGHT
ON/OFF
Default Value: OFF
NR (Noise Reduction)
Adjustable Value: 0-5
Default Value: 3
WB (White Balance)
Default Value: Auto
Auto/Manual/Outdoor/Indoor/One Push/ATW
(Manual Settings):
◦ R GAIN (Red Gain)
Default Value: 64
◦ B GAIN (Blue Gain)
Default Value: 84
Adjustable Scope: 0-255
Adjustable Scope: 0-255
•
AE (Auto Exposure)
Auto/Manual
(Manual Settings):
◦
◦
◦
Default Value: Auto
SHUTTER
Default Value: 1/1
Shutter Speed Range: 1/1-1/10000
IRIS
Close/F1.4-f22
Default Value: Close
BRIGHT
Set Brightness 0 - 31
Default Value: 0
Ver 1.1 6/26/14
IR Remote Controller (Note: Some buttons do not operate for all
camera models)
1.
2.
3.
4.
5.
Reset:
Restarts the camera and restores it
to Factory Default settings.
(Note: Will delete all memory).
Camera Selection
Select Camera ID: 1, 2 or 3
Preset Positions
1-9: Preset Positions
Set: Setting Preset Position
Clear: Clear Preset Position
Call: Call Preset Position
Note: If you want to set (or call) the first
preset position to 1, you should press
number key “1”, then press
“Set” (or “Call”) to set (call) the position.
Fast Zoom in/out Control Zone
+: Zoom in quickly
-: Zoom out quickly
Pan/Tilt Controller
Move Up
Move Down
Move Left
Move Right
6.
7.
8.
9.
10.
Auto Pan
Additional Function Zone
Freeze: Image Freeze
BL: Back-light Compensation
WB: White Balance
AE: Auto Exposure
D Zoom: Digital Zoom
HDMI: Swap to HDMI video output
DVI: Swap to DVI video output
Format: Swap between different formats
Power Supply Switch
Switch for turning camera on
(i.e. Stand-By mode vs. Working mode)
OSD Menu Zone
Dome OSD: Enter Pan Tilt Zoom OSD menu
Lens OSD: Enter lens OSD menu
Slow Zoom In/Out Zone
+: Zoom in slowly
-: Zoom out slowly
Focus Control Zone
Auto: Turn on auto focus
Manual: Turn on manual focus
Far: Set focus at farther distance
Near: Set focus at nearer distance
Ver 1.1 6/26/14
11.
Pan/Tilt Function Zone
L-Limit: Set left boundary limit scanning position
Scan: Enable Boundary Scanning (Auto Panning)
R-Limit: Set right boundary limit scanning position
Home: Go to camera’s Home position
Tour: Enable automatic patrol tour of presets
Rev: Enable image flip for ceiling mounting
Connection Instructions………………………………………………………………………
1.
2.
3.
4.
Connect included Power Supply to the camera.
Wait for camera to come to Home Position.
Connect included USB 3.0 cable to camera and USB 3.0 port of PC.
Select and configure camera in your software of choice.
NOTE: Failure to follow this sequence may result in no connection to PC.
Care Of The Unit………………………………………………………………………………….
Remove dust or dirt on the surface of the lens with a blower (commercially
available).
Ver 1.1 6/26/14
Installation Instructions………………………………………………………………………
Desktop Installation………………………………………………………………………………
When using the HuddleCam on a desk, Make sure that it will stand level. If you
want to use the camera on an incline, make sure the angle is less than 15
degrees to ensure that the camera’s pan and tilt mechanism operates normally.
Tripod Installation…………………………………………………………………………………
When using the HuddleCamwith a tripod, screw the tripod to the bottom of the
camera. The tripod screw must fit below specifications:
Note: Tripod must stand on a level surface.
Ver 1.1 6/26/14
Ceiling Mount…………………………………………………………………………………………
Ver 1.1 6/26/14
Troubleshooting………….…………………………………………………………………………
Problem
There is no power to the
camera.
Cause
Power adapter is
disconnected from mains
or from camera.
Power switch is set to OFF.
Camera will not connect to USB cable is bad.
the PC via USB.
Camera connects
sometimes.
Camera unable to pan,
tilt, and/or zoom.
Remote control not
working.
Camera cannot be
controlled via VISCA.
The Camera is not working
at all.
Ver 1.1 6/26/14
Menu is currently
displayed on the screen.
Pan, tilt or zoom range
limit was reached.
The “camera select”
button on the remote
control is not set to match
the “IR select” switch
number set on the camera.
The connection between
the PC and camera is
incorrect.
Commands being sent are
incorrect.
No response or image from
camera.
Resolution
Check the connections
between the camera,
power adapter and mains.
If anything is
disconnected, reconnect
it.
Set the power switch to
ON.
Try new USB Cable
Connect USB only after
camera has completely
booted.
Retry after exiting the
menu.
Try to pan/tilt/zoom in
the other direction.
Choose the correct “IR
select” number to match
camera settings.
Refer to Cable Connection
Info section of this
manual.
Refer to VISCA manual.
Disconnect power, and
wait a few minutes, then
connect the power again.
Retry.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising