LABELVIEW 2015 Administrator`s Guide

LABELVIEW 2015 Administrator`s Guide
Administrator’s Guide
LV2015-AG-EN-090915
The information in this manual is not binding and may be
modified without prior notice.
Supply of the software described in this manual is
subject to a user license. The software may not be used,
copied or reproduced on any medium whatsoever, except in
accordance with this license.
No portion of this manual may be copied, reproduced or
transmitted by any means whatsoever, for purposes other
than the personal use of the buyer, unless written
permission is obtained from Teklynx Newco SAS.
©2015 Teklynx Newco SAS,
All rights reserved.
Table of Contents
Chapter 1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Welcome. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
What is this guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Who should read this guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1
1-1
1-1
1-2
1-2
Chapter 2: Installing the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Functional description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Installation procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Network Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Installing the Network License Manager . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Starting the License Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Installing the software on the workstations . . . . . . . . . . . . . . . . . . . . . . 2-7
License protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Hardware Key connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Error messages when launching the software . . . . . . . . . . . . . . . . . . . 2-10
Installing the driver key manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Software key protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
To activate the software key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
Chapter 3: Network Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
Managing users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum number of users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Managing shared resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shared document files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shared data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shared printing logfile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-15
3-15
3-18
3-19
3-19
3-19
3-19
ii
Administrator’s guide
Shared file timeout period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20
Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20
Notes for the network administrator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21
About this manual
Typographical This manual distinguishes between different types of
information using the following conventions:
conventions
• Terms taken from the interface itself, such as commands,
appear in bold.
• Keys appear in small caps, for example: Press the
key.
SHIFT
• Numbered lists indicate that there is a procedure to follow.
• When the conjunction -or- appears next to a paragraph, it
means there is the option of a different procedure for
carrying out a given task.
• When a menu command contains submenus, the menu
name, followed by the command to select, appears in bold.
Thus, “Go to File > Open” means go to the File menu, then
the Open command.
This symbol highlights important information on
how a particular command or procedure works.
Following this symbol, you will find hints and tips
for optimizing tasks, speeding up commands, and
other helpful information.
iv
Administrator’s Guide
CHAPTER
1
Introduction
Welcome!
TEKLYNX label design and integration software provides
an easy-to-use, user-friendly solution for printing bar code
labels and tags to meet compliance standards in any
industry.
What is this guide?
This guide provides information to help you understand
how to manage your labeling software in the context of an
enterprise environment.
Who should read this guide?
This Administrator’s Guide is for IT personnel (system
and network administrators) who are responsible for
managing the deployment of software applications,
specifically on the Microsoft Windows platform.
Chapter 1 - 2
Administrator’s Guide
Product description
Your product includes the following components:
• A DVD for the installation
• Complete documentation
• A license agreement and registration card
• A protection key, either electronic (software key) or hard
key (dongle)
System requirements
The configuration required for the software to run properly is
the same as most applications running on Windows:
• One of the 32- or 64-bit Windows® operating Windows:
Vista SP2, 7 SP1, 8, 8.1, 10, Server 2008 SP2, 2008 R2
SP1 or Server 2012.
• Computer with 2GB of free RAM (depending on the
system).
• A hard drive with at least 1.5 GB free disk space
(depending on the installation options).
• CPU: 2 Ghz minimum.
• Video card : DirectX 9 minimum.
• Administrator rights to the computer during the
installation procedure.
• System must have access to the Internet or have a
dedicated USB port.
Note
The ReleaseUS.html file contains the latest
information on the software. This information
supersedes the information contained in this
manual.
CHAPTER
2
Installing the Software
Functional description
The network (multi-user) packages allow you to control
access to the labeling software licenses over the network.
Using this utility, you can have multiple users accessing the
label design software at the same time, from anywhere on
the network.
To use the network/multi-user version of your labeling
software, you must install the Network License Manager
on the server or on a station that will serve as a server, then
install the labeling software on each workstation.
Installation of the Network License Manager
Workstation
Server
Workstation
Figure 1 Network Configuration Installation.
Chapter 2 - 4
Administrator’s Guide
Installation procedure
Before you start
Before you can install the software, the network
administrator must first define the structure of the network
for the group of users, specifically:
• Define the license server on which the Network License
Manager and the dongle will be installed.
• Define the client workstations that will use the labeling
software.
Network
Manager
The Network License Manager let you define the network
configuration of your labeling software. It includes:
• The Network License Manager (License Service)
• Network Settings Wizard, which helps you define the
network configuration.
• User Manager: The User Manager is installed with the
Network License Manager so you can define access
rights to the labeling software in a network setting.which
helps you define the network configuration.
Installing the
Network
License
Manager
Before installing the labeling software on all the workstations
that will use it, you must first install the License Service utility
on the server to configure the network.
To install the Network License Manager on the server:
1 Insert the DVD in the appropriate drive.
The Installation window is displayed.
If the DVD does not run automatically, go to Windows
explorer and expand the letter of the DVD drive. Double
click index.hta.
2 Select Network License Manager, which includes
License Service and User Manager. Then, click the Install
button.
3 Follow the instructions on the screen.
4 If you want to define settings for your network
Installing the Software
Chapter 2 - 5
Share the TKDongle folder with full control, using
TKDongle as the share name. The default access path
for this folder is
For XP:C:\DocumentsandSettings\AllUsers\
ApplicationData\ TKI\ LicenseManager\TKDongle
For Vista, 7, 8, 8.1, 10, Server 2008 and Server 2012:
C:\ProgramData\TKI\LicenseManager\ TKDongle)
RIGHT CLICK > Properties > Sharing tab and
Permissions button.
configuration, start the Network Settings Wizard on the
server. If you do not modify the configuration, each
workstation will have its own settings.
For administrators:
Users wanting Write Access to the Network
license must be given the rights by:
1. Sharing the TKDongle folder and authorizing
the user:
For XP:C:\DocumentsandSettings\AllUsers\
ApplicationData\ TKI\ LicenseManager\
TKDongle
For Vista, 7, 8, 8.1, Server 2008 and Server
2012:
C:\ProgramData\TKI\LicenseManager\
TKDongle)
Right-click > Properties > Sharing tab and
Permissions button.
2. Give Write Access to the user on the Security
tab of the TKDongle properties.
Configuration
All the necessary tools to configure the network version are
available from the Network toolbar, which can be accessed
Chapter 2 - 6
Administrator’s Guide
from:
For Windows versions older than Windows 8: Start >
Programs > Teklynx Network License Manager and
selecting Network Toolbar.
For Windows 8 and 8.1 users: Access the search tool. To
access and use the search tool, open the Charms menu by
pressing Win [Windows key] + C on your keyboard or by
swiping in the top-right or bottom-right corner. Once the
Charms menu pops open, click/tap the Search button. Type
Teklynx Network License Manager.
The Network Settings Wizard helps you define the settings
for your network version.
1 Start the Network Settings Wizard.
2 Select a settings mode: Generic, By user or By station.
• Generic: All users will use the same settings on
all workstations. (user.ini).
• By user: Each user can access his or her own settings
on any workstation. (user name.ini).
• By station: Each workstation has its own settings
(station.ini).
3 Specify the location in which you want to store these
settings. If you want to share these settings between various
workstations, specify a network path accessible to all
workstations. (for example TKDongle).
4 Specify the location in which you want to store the shared
data (variables, lists, printing logfile, etc.). Be sure all users
have appropriate access on these folders.
To configure the User Manager
If you want to define network access rights for all users of
the labeling software, you must do so in the User Manager
(for more information, consult the User Manager help
system).
Click the User Manager icon
on the Network toolbar.
Installing the Software
Starting the
License Service
Chapter 2 - 7
Before installing the labeling software on all workstations,
you must be sure the License Service is started.
The License Service was installed as a service called
SLicense. You do not need to manually start it. In fact,
SLicense starts when the workstation is turned on and runs
as a background task as long as the workstation is on.
If you installed the Service License as software key
protected, you must activate the license before it will
start automatically.
To start the Service Controller
• Click the
icon on the Network toolbar
-orDouble-click the SLICENSECTRL.EXE file.
Installing the
software on the
workstations
The labeling software must be installed on all the
workstations on which it will be used.
To install the software on a workstation
1 Insert the DVD for the installation in the appropriate drive.
The Installation window is displayed.
If the DVD does not run automatically, Go to Windows
explorer and expand the letter of the DVD drive. Double
click on index.hta.
2 Select the product to be installed, click the Install button,
and follow the instructions on the screen.
3 Start the labeling software. The License Manager is
displayed. Click Try to launch the software. A message is
displayed to inform you that no dongle has been found. Click
Yes to start the software.
4 From the Tools menu, choose Network Administration.
5 Enable Use Network License.
6 Click Modify to select the server on which the License
Chapter 2 - 8
Administrator’s Guide
Manager and dongle are installed.
- or Click Browse to automatically search for the server on
which the License Service is installed.
If the network settings have already been configured, a
message asking if you want to use the current network
configuration is displayed.
7 If you want to modify or configure the network settings,
click the Network Settings Wizard button
.
8 Click OK.
9 Restart the program.
If the server is changed, you will have to update all
of the workstations. In this case, start the labeling
software and choose Tools > Network
Administration. Disable and re-enable the Use
Network License option.
License protection
Your software can be protected using a software key (an
electronic code) or a hardware key (a dongle).
Without a protection key, the program will run in “evaluation”
mode. You will not be able to save and print your labels.
• The dongle is a small electronic device that you plug into
your PC’s parallel or USB port before launching the
software.
• The software key is an electronic code that is requested
by the License Manager when you launch the software for
the first time or as long as you have not activated the
software.
You must first install the software and then activate or
connect the protection key to your computer.
Installing the Software
Hardware Key
protection
Chapter 2 - 9
The protection key must be installed on the computer on
which the License Service is installed. A single protection
key, pre-programmed with the number of licenses
purchased, is included with the network version of your
software.
The dongle must be installed before the License Service
can be started.
If you have purchased a software with a dongle, you can
choose between a USB or parallel port dongle.
Connecting the parallel key
Figure 2 Connecting the dongle to the parallel port on your PC
If you need to use a printer on the same parallel
port, simply plug it into the software protection key.
In this case, it might be necessary to turn the
printer on in order for the software protection key
to be recognized.
Connecting the USB key
Figure 3 Connecting the dongle to the USB port of your PC
When you use a USB key and have multiple USB ports, it
does not matter which port you use. If you do not have an
Chapter 2 - 10
Administrator’s Guide
available USB port, you can use a USB expander hub. USB
devices are hot-swappable, meaning you can plug and
unplug them at any time without restarting the PC.
Note
Drivers can be installed while the application is running.
However, you must restart your labeling software for
the changes to take effect.
Error messages
when launching
the software
If you receive an error message when launching the
software, please check the following items:
• Administrative rights. You must have local administrative
rights on your PC for the key installation to work
properly. If you do not have these access rights, you will
see an error message when launching the software, and
you will have to manually install the drivers.
• Driver installation. If you had trouble during installation or
if you receive an error message when launching the
software, you will have to manually install the drivers.
• The key. If you receive an error message when launching
the software, check that the connected key works with
your software.
• Driver update. If you receive an error message when
launching the software, your driver may not be updated.
To update your driver, download the new version from
http://www.aladdin.com/support/hasp/enduser.aspx
Installing the
driver key
manually
To manually install the key driver:
1 Go to Windows explorer.
2 For Windows XP and Server 2003:
Enter C:\Program Files\TKI\[software
version]\Common\Tools\Dongle\ then type the following
command: \HaspDinst.exe -i
For Windows 7, 8 , 8.1 Server 2008 and Server 2012, 64bit machines:
Enter C:\Program Files (x86)\Common Files\TKI\Dongle\
then type the following command: \HaspDinst.exe -i
Installing the Software
Chapter 2 - 11
For 32-bit machines:
Enter C:\Program Files \Common Files\TKI\Dongle\ then
type the following command: \HaspDinst.exe -i
Note
It is recommended that you close your labeling software
and other applications before installing your driver.
Software key
protection
Once you have installed the labeling software, the License
Manager will be launched, taking you step-by-step through
the software key protection process.
To activate the software key
1 In the License Manager, select Activate.
There are four possible activation methods: Online
activation, Using a USB key, Using a smartphone and
Using our website.
Note
If you have an Internet connection on the computer
where the software is installed, online activation is
automatically selected.
Online activation
Some enterprise networks are protected by a proxy server.
In this case, there is an extra step which allows you to enter
the IP address and connect to the Internet.
1 Enter the Serial number and the password provided with
the product and click Next.
2 Enter or edit your information in the User Registration
form. Click Next.
3 Click Finish.
Note
If you do not have an Internet connection on the
Chapter 2 - 12
Administrator’s Guide
computer where the software is installed but you have
access to another computer with an Internet
connection, you can activate the product using a USB
key.
Using a USB key
1. Enter the Serial number and the password provided
with the product and click Next.
2. Select Using a USB key.
3. Select the media to be used for activation (USB key or
external hard disk or network drives) and click Next. Files
for activation will be copied onto the selected media.
4. USB devices only: Unplug the removable media and plug
it into the computer connected to Internet.
5. On the computer connected to the Internet, double-click
USBWizard.exe (which can be found on the root of the
media). This will start the License Manager.
6. Select the license(s) to activate and click Next.
7. Enter or edit your information in the User Registration
form. Click Next.
A message will inform you that the activation information
for the selected license(s) has been successfully
retrieved.
8. USB devices only: Unplug the removable media from
this computer and plug it back into the computer where
the software is installed.
9. On the computer where the software is installed, doubleclick USBWizard.exe again (the file can be found on the
root of the media).
The wizard will display the license that can be activated on
the computer where the software is installed.
10. Click Next.11.
Installing the Software
Chapter 2 - 13
Click Finish.
If any problems were encountered, a message will inform
you that the activation has failed and an error will be
displayed.
Note
If you do not have access to a computer with an Internet
connection, you can activate the product using a
smartphone.
Using a smartphone
A barcode scanner application is required to read the
barcode which allows you to activate your software using a
smartphone. You can download this from your application
store / market. This activation mode uses an Internet
connection on your smartphone.
1 Enter the Serial number and Password provided with the
software and click Next.
2 .Select Using a smartphone.
3 Input your information in the User Registration form. Click
on Next.
4 A barcode appears. Move the cursor over the barcode to
zoom in.
5 Open your barcode scanner application on
your smartphone.
6 Scan the barcode with your smartphone.
7 Click Continue or open the browser on the phone.
8 The Software Activation website is displayed. This allows
you to register and activate your software. All fields must
be filled in.
9 Click Submit.
Chapter 2 - 14
Administrator’s Guide
The Validation code and Installation code are
displayed at the bottom of the Software Activation website
page. Please scroll down if necessary.
10 Enter the Validation code and Installation code in the
wizard (using uppercase characters).
11 Click Next.
12 Click Finish.
Using our website
1. Enter the Serial number and Password provided with
the software and click Next.
2. Select Using our website.
3. The link provided on this screen (http://www.teklynx.eu/
nsp/) can be reached from a different computer with
Internet access. You or someone else with an Internet
connection can connect to our website to complete the
activation. The Serial Number and Password (provided
with the product) and the User Code (displayed in the
wizard) will be required in order to use this service.
4. Enter the license user's information in the User
Registration form displayed on our website. Click Next.
5. Click Submit.
6. The Validation code and Installation code are
displayed on our website. Enter these in the wizard (using
uppercase characters) and click Next.
7. Click Finish.
CHAPTER
3
Network Use
Managing users
License
Service
Controller
The License Service is installed as a service. This service,
referred to as SLicense, is enabled automatically when the
server is turned on.
The
License Service Controller module, named
SLicenseCtrl.exe, is used to control how the service
functions and to change the standard behavior of the
License Service. You can, for example:
• Start or stop the service
• Display the list of users connected to the labeling
software
Description of the License Service Controller window
• To start License Service Controller, click on the icon on the
Network toolbar.
Once started and the window is enabled, the License
Service Controller window is displayed as follows:
Chapter 3 - 14
Administrator’s Guide
Figure 1
Main Service Control window
The License Service Controller window displays the list of
users. This list permanently displays the login name of those
currently using the labeling software.
Network Use
Chapter 3 - 15
The License Server Controller window toolbar contains the
following buttons:
Button
Function
Stops the service.
Starts the service.
Refreshes the display: The list of users may not
be updated in certain cases, such as if a
workstation crashes. To reset a workstation,
press CTRL+ALT+DEL.
Accesses the Service Control Settings window.
This button is only available when the service is
stopped.
Displays the About window. This window
displays the version number of the program.
The Indicator Panel
The Indicator panel displays the current status of the
service.
Indicator = Red: The
service is stopped.
Indicator = Orange:
The service is starting
up.
Indicator = Green: The
service is enabled.
Chapter 3 - 16
Administrator’s Guide
The Settings dialog box
To access the Settings window:
• Click
.
The Settings window is displayed.
Figure 2 Settings window
To change the settings
If SLicense.exe was not installed in the [DONGLE] folder, you
must specify the access path to the license file.
1 Enter the new access path to the license file, or click the
Browse button.
2 If you want to allow the service to be stopped while users
are still logged on, select the Enable stopping while users
are connected option.
3 If you want to change the display language of the License
Service Controller, select the desired language from the
Language list.
4 If you want to change the tolerance period in case of
Network Use
Chapter 3 - 17
network disconnection, enter the desiderated value in
minutes (max. 480 minutes).
By default there is no tolerance (0 minute). If the network is
disconnected, the labeling software stops working.
Note: The tolerance period begins after about 6 minutes of
connection to the server.
However, you can modify this tolerance. You can define
another value, in minutes (Max. 480 minutes), that will allow
you to continue using your labeling software even if the
network is disconnected.
Note: The user token will be locked during that period of
tolerance.
5 Click OK to update the changes.
Changing the behavior of the service
By default, the service is started automatically when
workstation is turned on. However, you can change
behavior of the service in the Services window in
Windows Control Panel. For more information, refer to
documentation supplied by Microsoft.
the
the
the
the
Changing the service startup type
1 Select SLicense from the list of services.
2 Click Startup.
3 Enable the desired startup type. SLicense is configured to
start automatically by default.
Selecting a user account
1 Select the user account in the Log on as field.
2 Type and confirm the password and click OK in
the Service window.
Chapter 3 - 18
Maximum
number of users
Administrator’s Guide
In case you installed the License Service on a Windows®
workstation your network version is limited to a maximum
number of users. This means that a 10-user license allows
you to start 10 sessions of the labeling software
simultaneously. If an eleventh user tries to log on, an error
message is displayed indicating that the maximum number
of users has been reached. He or she must wait until one of
the connected users logs off.
To increase the simultaneous connections, you have to
install the License Service on a Windows® Server.
Troubleshooting
Two types of error messages can be displayed. The table
below lists possible problems and describes the
troubleshooting procedure.
Message
Solution
Protection key
not found
- The key is not connected.
- The dongle is connected to the wrong
port (serial port, for example).
- A printer is connected to the dongle
and is switched off.
- The product has not been activated.
License Service
cannot create
the license file
The license file could not be created in
the [TKDongle] folder. This may mean
that a user on the station on which
License Service was started does not
have the access rights required to write
to this folder. The network administrator
must assign the required access rights
(read, write, delete, and modify, if
applicable).
Network Use
Chapter 3 - 19
Managing shared resources
Shared
document files
A document can only be opened by one user in read/write
mode. If the same document is opened by other users, it is
opened in read-only mode. This means that only the first
user can modify and save the document.
Note: The document can be printed from read-only
mode.
To provide security for the work of the group, the opening
mode for documents can be defined in the Tools >
Configuration > Document tab, by selecting the Open
documents as «read only» mode by default option.
Shared data
The Network Settings Wizard is used to configure data
sharing for variables, lists of values, and the printing logfile.
To share data, you must specify a path and folder on the
network in step 3 of the wizard.
Shared printing
logfile
If you selected the generic settings mode in the
Network Settings Wizard, the printing logfile (which is very
useful for tracking all print jobs) can be configured in the
printing logfile window.
To share the printing logfile with all workstations, you must
first generate the log file on one of the workstations.
To generate a printing logfile
1 Go to Tools > Logfile.
2 Enter the access path to the folder in which shared data
is saved and a file name for the printing logfile, then select a
text editor.
3
Enable your options on the Options tab. For more
Chapter 3 - 20
Administrator’s Guide
information on the printing logfile, refer to the online Help
system.
Note
As with shared variables, if multiple users are working on the
same file, only one printing logfile is created and it tracks all
print jobs for each user. However, a user can generate a
personal file.
Shared file
timeout period
When a shared file, such as a file of shared variables, is
opened by a user, it cannot be accessed by other users.
Others users must wait until it becomes available before
editing it. After a timeout period (defined by you), a message
is displayed asking the user if he or she wants to continue
waiting or cancel the request.
To define the timeout period:
1 Go to Tools > Configuration.
2 Click the Others tab.
3 Type a value in the Shared files access timeout (ms) field.
Printing
A flashing colored indicator indicates the status of the
current print job in the Print Status windows. This status is
only displayed if you display the Print window in the labeling
software.
• Green: The data is being printed.
• Orange: A user is currently using a shared resource
(printer or variable).
• Red: Error.
To display the print dialog box:
1 Go to Tools > Configuration and click the Printing tab.
2 Disable the Hide Cancel Print dialog box option.
Network Use
Chapter 3 - 21
Notes for the network administrator
This section describes folders on the server and
workstations, and the required access rights.
Folders on the server
During installation, the [TKDONGLE] folder is created. It is
important for each user to have read/write access to the
shared TKDONGLE folder.
Note
Users must be given, at minimum, read/write access to all
available folders in the default folders list (Tools >
Configuration> Default folders).
France
33-562-601-080
Germany
49-2103-2526-0
Singapore
65-6908-0960
United States
1-414-837-4800
Copyright 2015 Teklynx Newco SAS. All rights reserved. TEKLYNX and LABELVIEW are trademarks or registered trademarks
of Teklynx Newco SAS or its affiliated companies. All other brands and product names are trademarks and/or copyrights of
their respective owners.
www.teklynx.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising