QUICK START GUIDE: I/O Expansion Card

QUICK START GUIDE: I/O Expansion Card
QUICK START GUIDE: I/O Expansion Card
What Ships in the Box
Important Safety Instructions
• I/O card.
!
@
#
$
%
• Card bracket.
• 2 black 4-40 Phillips head screws.
• 3 stainless steel 4-40 Phillips head screws.
• 2 or 4 detachable three position 3.81 mm
terminal block connectors.
Note: Terminal block connectors are not included
with the 2 Line Analog Telephone Interface Card
and/or 2 Line VoIP Interface Card.
• This Quick Start Guide.
What You Need to Provide
^
&
• Radius 12x8 EX, Radius AEC, or Edge.
• Anti-static work station.
Composer, the Windows software that
configures Symetrix Dante Network Audio
hardware, includes a help file which acts as
a complete User’s Guide for both hardware
and software. If you have questions beyond
the scope of this Quick Start Guide, contact
our Customer Support Group in the following
ways:
Heed all warnings.
Do not use this apparatus near water. This
apparatus shall not be exposed to dripping
or splashing and no objects filled with
liquids, such as vases, shall be placed on
the apparatus.
No user serviceable parts inside. Refer servicing to qualified service personnel.
Il ne se trouve a l’interieur aucune piece pourvant entre reparée l’usager.
S’adresser a un reparateur compétent.
G
The lightning flash with arrowhead
symbol within an equilateral triangle is
intended to alert the user of the presence
of uninsulated “dangerous voltage” within
the product’s enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons. The exclamation
point within an equilateral triangle is
intended to alert the user of the presence
of important operating and maintenance
(servicing) instructions in the literature
accompanying the product (i.e. this Quick
Start Guide).
G
CAUTION: To prevent electric shock, do
not use the polarized plug supplied with the
device with any extension cord, receptacle,
or other outlet unless the prongs can be
fully inserted.
G
Power Source: This Symetrix hardware
uses a universal input supply that
automatically adjusts to the applied
voltage. Ensure that your AC mains voltage
is somewhere between 100-240 VAC,
50-60 Hz. Use only the power cord and
connector specified for the product and
your operating locale. A protective ground
connection, by way of the grounding
conductor in the power cord, is essential
for safe operation. The appliance inlet and
coupler shall remain readily operable once
the apparatus has been installed.
G
User Serviceable Parts: There are no
user serviceable parts inside this Symetrix
product. In case of failure, customers
inside the U.S. should refer all servicing to
the Symetrix factory. Customers outside
the U.S. should refer all servicing to an
authorized Symetrix distributor. Distributor
contact information is available online at:
http://www.symetrix.co.
Do not block any ventilation openings.
Install only in accordance with the
manufacturer’s instructions.
(
This apparatus shall be connected to
a mains socket outlet with a protective
earthing connection. Do not defeat
the safety purpose of the polarized or
grounding-type plug. A polarized plug has
two blades with one wider than the other.
A grounding type plug has two blades and
a third grounding prong. The wide blade
or the third prong are provided for your
safety. If the provided plug does not fit
into your outlet, consult an electrician for
replacement of the obsolete outlet.
7:00 am to 5:00 pm
Monday through Friday,
Pacific Time
Web:
http://www.symetrix.co
BL
Email:
Chat:
support@symetrix.co
http://symetrix.casengo.com/vip/
Ensure proper ESD control and grounding
when handling exposed I/O terminals.
BM
Protect the power cord from being walked
on or pinched particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
BN
Only use attachments/accessories
specified by the manufacturer.
BO
Use only with the cart, stand, tripod,
bracket, or table specified
by the manufacturer,
or sold with the
apparatus. When a cart is
used, use caution when
moving the cart/apparatus
combination to avoid injury from tip-over.
www.symetrix.co | +1.425.778.7728
DE CHOC ELECTRIQUE
AVIS: RISQUE
NE PAS OUVRIR
SEE OWNERS MANUAL. VOIR CAHIER D’INSTRUCTIONS.
Clean only with dry cloth.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Modifications not expressly approved by the manufacturer could void the
user’s authority to operate the equipment under FCC rules.
Cet appariel numerique de la classe B respecte toutes les Exigences du
Reglement sur le materiel brouilleur du Canada.
The 2-line analog telephone interface card device is in compliance
with the Federal Communications Commission’s (FCC) Rules and
Regulations 47 CFR Part 68, and the Administrative Council on Terminal
Attachments (ACTA) – adopted technical criteria, TIA-968-B – Telephone
Terminal Equipment, Technical Requirements For Connection of Terminal
Equipment To The Telephone Network, August 2009 and TIA-1096.
The 2-line analog telephone interface card device meets the Industry
Canada technical specifications CS-03 Part I for terminal equipment and
related access arrangements intended for direct connection to analogue
wireline facilities and DC-01(E) for the declaration of conformity and
registration of terminal equipment. The Ringer Equivalence Number
(REN) is an indication of the maximum number of devices allowed to be
connected to a telephone interface. The REN for the Analog Telephone
Interface (ATI) card is two. The termination of an interface may consist of
any combination of devices subject only to the requirement that the sum
of the REN’s not exceed two per ATI card. Multiple ATI Cards may be
installed to increase the REN for a system.
TO REDUCE THE RISK OF FIRE OR
SHOCK DO NOT EXPOSE
WARNING: ELECTRIC
THIS EQUIPMENT TO RAIN OR MOISTURE
Follow all instructions.
Do not install near any heat sources such
as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that
produce heat.
Tel:+1.425.778.7728
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Keep these instructions.
*
Getting Help
CAUTION
Read these instructions.
BP
Unplug this apparatus during lightning
storms or when unused for long periods of
time.
BQ
Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug cord
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or has
been dropped.
1 of 4
QUICK START GUIDE: I/O Expansion Card
ESD Warning
The following precautions must be taken:
an even downward pressure until you feel the card seat into
the 50-pin socket. You will likely need to carefully move the
board side to side to align the 50-pin connector. Use one
of the stainless steel screws provided and mount the board
to the standoff. Do not over tighten this screw. The 50-pin
connector on the Symetrix I/O cards should not be under
any tension when properly installed.
• Do not open the protective conductive packaging until you have read the following, and are at an approved anti-
static work station.
Now, install and tighten the 2 remaining stainless steel
screws that mount the bracket to the card. This should
ALWAYS be the last step before replacing the lid.
• Use a conductive wrist strap attached to a good earth ground.
Finally, replace the lid.
This product can be damaged by electrostatic discharge
(ESD). When handling, care must be taken so that the
devices are not damaged. Damage due to inappropriate
handling is not covered by the warranty.
• Always discharge yourself by touching a grounded bare metal surface or approved anti-static mat before picking up an ESD-sensitive electronic component.
• Use an approved anti-static mat to cover your work surface.
The IN, OUT, AEC and DIGI LEDs on the front of the Radius 12x8
EX, Radius AEC, or Edge frame will illuminate in combination to
indicate the card type installed. For example, an IN illuminates
to indicate an analog mic/line input card, whereas IN and DIGI
illuminate to indicate a digital input card. The IN and OUT LED’s
illuminate to indicate a analog telephone interface card. If the
card is installed properly, the card type LED(s) will illuminate.
Card Set-up and Configuration
Remove Installed Card
Once you are properly grounded, follow this sequence of
steps to properly set-up and configure Symetrix I/O cards in
your Radius 12x8 EX, Radius AEC, or Edge hardware.
1
2
3
4
First, make sure the unit is powered down. Next, you must
remove the lid. To do this, 3 Phillips head screws need to be
removed from the top of the frame. Slide the lid back and
then up when removing. There is a lip that holds the front
down to the chassis.
If your Radius 12x8 EX, Radius AEC, or Edge unit has blank
filler panels in the card slots, unscrew and remove them by
removing the two black screws located on the outside of the
frame.
To remove an installed card, first remove the 2 stainless
steel screws that mount the card bracket to the card. These
screws are located on the inside.
Next remove the stainless steel Phillips head screw from the
top of the card. Gently pull the card up to disconnect the 50pin connector. The card is no longer attached to the frame.
Carefully remove the card from the chassis.
Install New Card
1
2
3
4
Remove the bracket for the I/O card by removing the two
black screws located on the outside of the frame. Unused
I/O card bays must have a blank filler panel installed when
operating a Radius 12x8 EX, Radius AEC, or Edge unit.
To install a new card, mount the bracket for the new I/O card
to the frame chassis using the two black screws provided.
Next, align and feed the connectors on the I/O card through
the opening in the bracket and align the single screw hole in
the card with the standoff on the motherboard. Look through
this hole and align with the standoff and then, carefully, apply
www.symetrix.co | +1.425.778.7728
2 of 4
QUICK START GUIDE: I/O Expansion Card
4 Channel Analog Input Card
4 Channel AEC Input Card
Connections:
Connections:
Using standard mic/line cables terminated on one end with
terminal block connectors and appropriate connectors for
your mic/line sources on the other end, connect the terminal
block ends into the Analog Mic/Line Inputs on the card and
the opposite ends into your source devices’ outputs. Refer
to the help module included in all Symetrix software for more
information on the 4 Channel Analog Input Card and audio
wiring.
Using standard mic/line cables terminated on one end with
terminal block connectors and appropriate connectors
for your mic/line sources on the other end, connect the
terminal block ends into the AEC Inputs on the card and the
opposite ends into your source devices’ outputs. Refer to
the help module included in all Symetrix software for more
information on the 4 Channel AEC Input Card and audio
wiring.
4 Channel Analog Output Card
Connections:
2 Line Analog Telephone Interface Card
Using standard mic/line cables terminated on one end with
terminal block connectors and appropriate connectors for
your destination devices on the other end, connect the
terminal block ends into the Analog Line Outputs on the
card and the opposite ends into your destination devices’
inputs. These outputs are +4 dBu balanced line level outputs
by default. If you need an unbalanced output, or more
information on the 4 Channel Analog Output Card, refer to
the analog audio wiring diagrams located in the help module
included in all Symetrix software.
Connections:
4 Channel Digital Input Card
Connections:
Using 100-Ohm (balanced, AES) or 75-Ohm (unbalanced
S/PDIF) cables terminated on one end with terminal block
connectors and appropriate connectors for your digital
sources on the other end, connect the terminal block ends
into the Digital Inputs on the card and the opposite ends
into your source devices’ outputs. These inputs have a
nominal sample rate of 48 kHz. They will accept any input
ranging from 12 to 96 kHz and sample rate convert to the
nominal rate of 48 kHz. Refer to the help module included in
all Symetrix software for more information on the 4 Channel
Digital Input Card and audio wiring.
Using a standard telephone cord terminated with RJ11
(6P6C) connectors, connect one end to the Line port on the
Analog Telephone Interface card and opposite end to the
telephone network (wall jack). Optionally, connect a standard
analog telephone, dialer, audible and/or visual ringing device
to the Set port of the Analog Telephone Interface Card using
another telephone cord.
Note: At this time, the Symetrix 2 Line Analog Telephone
Interface Card is only certified for use with US and Candian
Public Switched Telephone Networks.
2 Line VoIP Interface Card
Connections:
Using a standard CAT5/6 cable terminated with RJ45
connectors, connect one end to the port on the 2 Line VoIP
Interface card and opposite end to the VoIP network. Refer
to the help module included in all Symetrix software for more
information on the 2 Line VoIP Interface Card.
ATTENTION: Upgrade the hosting SymNet DSP unit’s
ATTENTION:
Upgrade
hosting
firmware
using SymNet
Composerthe
version
2.5 or later
BEFORE
installing
2 Linefirmware
VoIP Interface
Card.
Symetrix
DSPthe
unit’s
using
Composer version 2.5 or later BEFORE
installing the 2 Line VoIP Interface card.
4 Channel Digital Output Card
Connections:
Using 100-Ohm (balanced, AES) or 75-Ohm (unbalanced,
S/PDIF) cables terminated on one end with terminal block
connectors and appropriate connectors for your destination
devices on the other end, connect the terminal block ends
into the Digital Outputs on the card and the opposite ends
into your destination devices’ inputs. These outputs use
a sample rate of 48 kHz by default. If you need a different
sample rate, connect an appropriate Word Clock, AES-3/11
clock or S/PDIF clock source to the corresponding Clock
Input(s) on the card. Refer to the help module included in
all Symetrix software for more information on the 4 Channel
Digital Output Card and audio wiring.
www.symetrix.co | +1.425.778.7728
3 of 4
QUICK START GUIDE: I/O Expansion Card
The Symetrix Limited Warranty
Buyer Responsibilities:
By using Symetrix products, the Buyer agrees to be bound by the terms of
this Symetrix Limited Warranty. Buyers should not use Symetrix products
until the terms of this warranty have been read.
Symetrix recommends the Buyer make backup copies of site files before
having a unit serviced. During service it is possible that the site file will be
erased. In such an event, Symetrix is not responsible for the loss or the time
it takes to reprogram the site file.
What is Covered by this Warranty:
Symetrix, Inc. expressly warrants that the product will be free from defects
in material and workmanship for three (3) years from the date the product is
shipped from the Symetrix factory. Symetrix’ obligations under this warranty
will be limited to repairing or replacing, at Symetrix’ option, the part or parts
of the product which prove defective in material or workmanship within the
warranty period provided that the Buyer gives Symetrix prompt notice of any
defect or failure and satisfactory proof thereof. Symetrix may, at its option,
require proof of the original date of purchase (copy of original authorized
Symetrix Dealer’s or Distributors invoice). Final determination of warranty
coverage lies solely with Symetrix. This Symetrix product is designed and
manufactured for use in professional audio systems and is not intended for
other usage. With respect to products purchased by consumers for personal,
family, or household use, Symetrix expressly disclaims all implied
warranties, including, but not limited to, warranties of merchantability
and fitness for a particular purpose. This limited warranty, with all terms,
conditions and disclaimers set forth herein, shall extend to the original
purchaser and anyone who ‑‑purchases the product within the specified
warranty period from an authorized Symetrix Dealer or Distributor. This limited
warranty gives the Buyer certain rights. The Buyer may have additional rights
provided by applicable law.
What is not Covered by this Warranty:
Legal Disclaimers and Exclusion of other
Warranties:
The foregoing warranties are in lieu of all other warranties, whether oral,
written, express, implied or statutory. Symetrix, Inc. expressly disclaims
any IMPLIED warranties, including fitness for a particular purpose or
merchantability. Symetrix’ warranty obligation and Buyer’s remedies
hereunder are SOLELY and exclusively as stated herein.
Limitation of Liability:
The total liability of Symetrix on any claim, whether in contract, tort
(including negligence) or otherwise arising out of, connected with, or
resulting from the manufacture, sale, delivery, resale, repair, replacement
or use of any product will not exceed the retail price of the product or
any part thereof which gives rise to the claim. In no event will Symetrix
be liable for any incidental or consequential damages including but not
limited to damage for loss of revenue, cost of capital, claims of Buyers for
service interruptions or failure to supply, and costs and expenses incurred
in connection with labor, overhead, transportation, installation or removal
of products, substitute facilities or supply houses.
Servicing a Symetrix Product:
This warranty does not apply to any non-Symetrix branded hardware
products or any software even if packaged or sold with Symetrix Products.
Symetrix does not authorize any third party, including any dealer or sales
representative, to assume any liability or make any additional warranties or
representation regarding this product information on behalf of Symetrix.
The remedies set forth herein shall be the Buyer’s sole and exclusive
remedies with respect to any defective product. No repair or replacement
of any product or part thereof will extend the applicable warranty period
for the entire product. The specific warranty for any repair will extend for
a period of 90 days following the repair or the remainder of the warranty
period for the product, whichever is longer.
This warranty also does not apply to the following:
1. Damage caused by improper use, care, or maintenance or failure to follow the instructions contained in the Quick Start Guide or Help File.
2. Symetrix product that has been modified. Symetrix will not perform repairs on modified units.
3. Symetrix software. Some Symetrix products contain embedded software or apps and may also be accompanied by control software intended to be run on a personal computer.
4. Damage caused by accident, abuse, misuse, exposure to liquids, fire, earthquake, acts of God, or other external causes.
5. Damage caused by service (including upgrades and expansions) performed by any person not authorized by Symetrix.
6. Cosmetic damage, including but not limited to scratches and dents, unless failure has occurred due to a defect in materials or workmanship within the warranty period.
Residents of the United States may contact the Symetrix Technical
Support Department for a Return Authorization (RA) number and
additional in-warranty or out-of-warranty repair information.
If a Symetrix product requires repair services outside of the United States
please contact the local Symetrix dealer or distributor for instructions on
how to obtain service.
Products may be returned by Buyer only after a Return Authorization
number (RA) has been obtained from Symetrix. Buyer will prepay
all freight charges to return the product to the Symetrix factory. Symetrix
reserves the right to inspect any products which may be the subject of
any warranty claim before repair or replacement is carried out. Products
repaired under warranty will be returned freight prepaid via commercial
carrier by Symetrix, to any location within the continental United States.
Outside the continental United States, products will be returned freight
collect.
7. Conditions caused by normal wear and tear or otherwise due to the normal aging of Symetrix products.
8. Damage caused by use with another product.
9. Product on which any serial number has been removed, altered or defaced.
10. Product that isn’t sold by an authorized Symetrix Dealer or Distributor.
www.symetrix.co | +1.425.778.7728
4 of 4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising