VIVOTEK Mounting Accessories AM-312 Pole mount Mechanical Drawings II AM-312 Pole mount bracket Installation Guide Revision History: 70,05 84,9 55° 2 55° Rev. 1.0: Initial release Corresponding ordering part numbers: AM-312: 900034800G, AM-715: 100134700G AM-714: 100134800G AM-218: 100146100G 102 6 Compatible VIVOTEK Cameras The pole mount bracket is designed to accommodate a pole in a diameter ranging from 90 ~ 152mm (3.5 ~ 6 inches) 102 45 7 Compatible brackets Supported Cameras AM-714 IB836B-HF3/6B-EHF3, IB836B-HT/6B-EHT, IB9371-HT/71-EHT, IB8382-F3/82-EF3, IB8382-T/82-ET, IB9381-HT/81-EHT, IB9371-HRT, IB9381-HRT AM-715 IB8367/67-R, IB8367-T/67-RT, IB8338-H/38-HR 170 I 86 AM-218 (via AM-714) Please refer to AM-218 documents. 173,79 Directly attached Supported Cameras * IB836B-HF3/6B-EHF3, IB836B-HT/6B-EHT, IB9371-HT/71-EHT, IB8382-F3/82-EF3, IB8382-T/82-ET, IB9381-HT/81-EHT, IB9371-HRT, IB9381-HRT AM-312 Applications * The directly-attached configuration is less recommended for the lack of waterproof and cabling protection. If directly attached, you should properly wrap the rear-end cables and connectors with waterproof protection such as putties. AM-312 AM-714 AM-218 AM-714 - or - AM-312 AM-715 Package Contents Items Bullet camera 1. Pole mount bracket, 2. Stainless strap x2, 3. M6X20mm screws x4. 4. M5X20mm screws x4, 5. Hex L wrench 5mm x1, 6. Hex L wrench 4mm x1. AM-520 / AM-525, etc. M6X20 X4 M5X20 X4 5mm X1 4mm X1 Dome camera Stainless steeel strap X2 • • • III Installation Make sure you have purchased the adequate accessories to be combined for your installation. Please do not install an indoor camera in an outdoor environment! Doing so will void our warranty. This is determined by whether the camera housing is weather-proof. Direct sunlight can tremendously increase the temperature within the device. 4. Secure the AM-714 conduit box to bracket using the M5 screws, washers, and hex heads. A hex crescent wrench is required. Below is a general, sample procedure using a Pole mount bracket: 1. Pass the stainless steel straps through the bracket and around the pole. 2. Tighten the straps using a pincer plier and a flat blade screwdriver. Installation Torque: 35 lb-in(40kg-cm) M5 If you are installing a bullet camera directly to the bracket, use the M6 screws in the center. A hex crescent wrench is required. 3. The 4 screw holes in the center are used for directly mounting the IB series bullet cameras. The 4 screw holes at the edges are used for mounting the AM-714 conduit box. M5 For M6 socket screws - for IB series bullet cameras directly attached For M5 socket screws - for AM-714 conduit box 5. For the rest of the installation procedure, refer to the documentation that came with the AM-714, AM-715, AM218, and the other accessories. The 3/4" cable glands and conduts for protecting cables are user-supplied.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project