advertisement
IDT CAMERA SPECIFICATIONS
Users Manual
IDT Cameras
Specification Manual
1
IDT Camera Specifications
Document Revision
January 2017
Products Information www.idtvision.com
North America
1202 E Park Ave
TALLAHASSE FL 32301
United States of America
P: (+1) (850) 222-5939
F: (+1) (850) 222-4591 [email protected]
Europe via Pennella, 94
I-38057 - Pergine Valsugana (TN)
Italy
P: (+39) 0461- 532112
F: (+39) 0461- 532104 [email protected]
Eekhoornstraat, 22
B-3920 - Lommel
Belgium
P: (+32) 11- 551065
F: (+32) 11- 554766 [email protected]
Copyright © Integrated Design Tools, Inc.
The information in this manual is for information purposes only and is subject to change without notice. Integrated Design Tools, Inc. makes no warranty of any kind with regards to the information contained in this manual, including but not limited to implied warranties of merchantability and fitness for a particular purpose. Integrated Design Tools, Inc. shall not be liable for errors contained herein nor for incidental or consequential damages from the furnishing of this information. No part of this manual may be copied, reproduced, recorded, transmitted or translated without the express written permission of Integrated Design Tools,
Inc.
2 Users Manual
IDT Camera Specifications
Table of Contents
1. TERMS AND CONDITIONS..........................................................................6
2.3. Disconnect power prior to plugging or unplugging any cables........................12
3. INTRODUCTION TO THE CAMERAS........................................................13
4. PRODUCT SPECIFICATIONS....................................................................32
Users Manual 3
IDT Camera Specifications
4.6. Mechanical and hole mounts (OS V3 and CC series) ....................................76
4.7. Mechanical and hole mounts (Os V1 series)...................................................83
4.10. Mechanical and hole mounts (NX-Air series)................................................98
4.11. Mechanical and hole mounts (NX-Air with Wi-Fi module)..........................103
4.12. Mechanical and hole mounts (M series)......................................................108
4.13. Mechanical and hole mounts (XStream).....................................................115
4 Users Manual
IDT Camera Specifications
4.14. Mechanical and hole mounts (NR series)...................................................120
4.15. Mechanical and hole mounts (N series)......................................................131
4.16. Mechanical and hole mounts (X series)......................................................136
Users Manual 5
IDT Camera Specifications
1.
Terms and Conditions
1.1.
Terms and Conditions
1. TERMS - These terms govern the sale of goods between Integrated Design Tools, Inc.
(“IDT”) and the Buyer (“Buyer”). This document acknowledges receipt of the Buyer’s order by
IDT, and confirms the sale of product evidenced by the invoice as expressly conditioned on the Buyer’s acceptance of the terms and conditions set forth herein.
2. PRICES – All published prices are subject to change without notice. Written quotations shall expire thirty (30) calendar days from the date of quotation unless withdrawn in writing sooner. Verbal quotations are provided for budgetary guidance only. Unless otherwise specifically stated, prices are in U.S. Dollars.
3. TERMS OF PAYMENT:
3a. Deposits – Buyer must make a deposit equal to the amount specified by IDT at the time of the order, typically 10% of the total order value (excluding any sales tax, freight, duties, import tax and delivery charges). Camera reservation numbers and delivery estimates are provided at the sole discretion of IDT.
3b. Method of Payment – Credit card payment via VISA, MASTERCARD, AMERICAN
EXPRESS or DISCOVER is provided as a convenience with valid credit card authorizations. Please contact the IDT Customer Service Department for Remit To information when transferring bank to bank payments or visit IDT’s website for bank information. All orders are payable in U.S. dollars (USD).
3c. Standard Payment Terms – All orders must be paid in full prior to shipment via wire transfer, cash equivalent (such as money order, cashier’s check, or personal check drawn from a United States bank), or credit card. IDT has the right to refuse any order, even after accepting payment or partial payment for such order. IDT will credit/refund any such payment made by the Buyer, if IDT rejects the order.
3d. Deposit Payments – Deposit payments may be remitted via credit card payments, wire transfer or cash equivalent (such as money order, cashier’s check, or personal check drawn from a United States bank). No more than two separate credit cards may be used for payment. IDT reserves the right to reject any order. IDT will credit or refund any payments made if IDT rejects the order.
3e. Immediate Order Payments – Immediate payments may be remitted via credit card payments, wire transfer or cash equivalent (such as money order, cashier’s check, or personal check drawn from a United States bank). No more than two separate credit cards may be used per payment. IDT reserves the right to reject any order. IDT will credit or refund any payments made if IDT rejects the order.
3f. Balance Payments – Buyer must pay the full remaining balance of the invoice before the order will be processed for shipment. Balance payments may be remitted via credit card payments, wire transfer or cash equivalent (such as money order, cashier’s check, or personal check drawn from a United States bank). No more than two separate credit cards may be used per payment. IDT reserves the right to reject any order. IDT will credit or refund any payments made if IDT rejects the order.
3g. Rentals/Leasing – IDT does offer rental/leasing options for various IDT products. IDT does not affiliate, authorize, or support any other entities offering leasing options for IDT
6 Users Manual
IDT Camera Specifications product. IDT assumes no liability for services or product offered by unauthorized thirdparty entities offering IDT product or services.
4. DELIVERY AND ACCEPTANCE – All product shipments shall be made from the IDT facility at Pasadena, California, at which time title and risk of loss shall pass to the Buyer.
Buyer shall be the importer of record for all purchased products, if applicable. Licensing requirements for importation to non-U.S. countries is the sole obligation of the Buyer. In the absence of specific shipping instructions from the Buyer, IDT will ship by the method it deems, in its sole discretion, most advantageous. Transportation charges will be collected prior to shipment. Unless otherwise indicated, Buyer is obligated to obtain insurance against damage to the product being shipped. Unless otherwise specified, products will be shipped in standard commercial packaging. When special packaging or export instructions are requested by the Buyer, any additional costs will be the responsibility of the Buyer. IDT reserves the right to reject certain shipping or packing methods.
IDT shall use reasonable efforts to notify Buyer of any anticipated delays in delivery. IDT will not be liable for any loss, damages or penalty resulting from delay in delivery.
Acceptance of the product by the Buyer shall occur no later than fifteen (15) days after shipment. Product not rejected during this fifteen-day period shall be deemed accepted, and all returns shall be handled in accordance the Returns section below. Product cannot be rejected by Buyer based on criteria that were unknown to IDT or based on test procedures that IDT does not conduct.
5. RESTRICTIONS ON USE – Buyer will not cause or permit the modification or reverse engineering of file formats, tools, or image processing of IDT products without express written consent from IDT. Buyer will not develop tools from IDT products or use non- IDT approved tools, products, or software with IDT products without express written consent from IDT.
Buyer will not cause or permit any reverse engineering of IDT products.
6. WARRANTY – IDT warrants all products will be of good quality and workmanship and free from material defects. Upon the expiration of the time periods identified below, all liabilities of IDT will terminate. In no event shall IDT be liable for consequential damages.
LIMITED WARRANTY – IDT hereby warrants that IDT’s products will be free from defects in material and workmanship under normal use according to the provisions and limitations, herein set forth. All parts, specifically EXCLUDING expendable ‘wear’ parts, that become unserviceable, due to defective material or workmanship, with two (2) years, parts and labor from date of the original retail purchase, shall at IDT’s option, be repaired or replaced.
LIMITATIONS – The obligations of IDT for breach of warranty shall be limited to products manufactured by IDT; (1) that are installed, operated, and maintained according to IDT’s instruction furnished and/or available to the purchaser upon request; (2) that are installed according to all other applicable Federal, State, and local codes or regulations; and (3) that the purchaser substantiates were defective in material and workmanship notwithstanding that they were properly installed and correctly maintained as set forth and were not abused or misused. The obligation of IDT shall be limited to replacing or repairing the detective product, at the option of IDT. IDT shall not be responsible for any labor or cost of removal or repairing or reinstallation of its products and shall not be liable for transportation costs to and from its operations in Pasadena, CA. Use of parts for modification or repair of the product or any component part thereof not authorized or manufactured by IDT specifically for such product shall void this warranty. This warranty shall not apply to any damage to or defect in the IDT’s products that is directly or indirectly caused by; (1) FORCE MAJEURE, act of GOD, or other accident not related to an inherent product defect; or (2) abuse, misuse, or neglect of the such product, including any damage caused by improper assembly, installation, adjustment, or faulty instruction of the purchaser. OTHER THAN AS EXPRESSLY SET FORTH HEREIN
ABOVE, IDT MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, WITH RESPECT
TO ANY OF IDT’S PRODUCTS, INCLUDED BUT NOT LIMITED TO ANY MERCHANT-
ABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL IDT BE
RESPONSIBLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY
NATURE SUFFERED BY IDT’S PRODUCTS. Any person or entity to whom this warranty
Users Manual 7
IDT Camera Specifications extends and who claims breach of warranty against IDT must bring suit thereon within one year from the date of occurrence of such breach of warranty or be forever barred from any and all legal or other remedies for such breach of warranty. IDT is not responsible for and hereby disclaims any undertaking, representation, or warranty made by any dealer, distributor, or other person that is inconsistent with or in any way more expensive than the provisions of this limited warranty. This warranty grants specific legal rights and shall be read in conformity with applicable state law. In some jurisdictions, the applicable law mandates warranty provisions that provide greater rights than those provided for herein. In such case, this limited warranty shall be read to include such mandates provisions; and any provision herein that is prohibited or unenforceable in any such jurisdiction shall, as to such jurisdiction, be ineffective to the extent of such prohibition or unenforceable without invalidating the remaining provisions and without affecting the validity or enforceability of such provisions in any other jurisdiction.
6a. Standard Warranty – A standard Warranty is granted to the original purchases by IDT for a period of two (2) years, parts and labor, for the camera and camera accessories excluding Standard Warranty for Digital Media is thirty (30) days. Standard Warranty for
Batteries is ninety (90) days or change cycles of less than 400, whichever comes first.
The Standard Warranty covers parts and labor charges for products that have been returned pre-paid shipment to an Authorized Service Center. All warranty returns shall be done in accordance with IDT’s warranty Return Merchandise Authorization (“RMA”) policy, a copy of which is set forth in the Returns section and is posted on IDT’s website.
Any repaired or replaced product shall be warranted as set forth in this section for a period the greater of (i) the balance of the applicable warranty period relating to such product or (ii) ninety (90) days after it is received by Buyer. Only the components that were repaired or replaced will be eligible for the 90-day period as set forth above.
IDT’s warranty does not include products that have defects or failures resulting from; (a) alterations, modifications or repairs by Buyer or unauthorized third parties or (b) accident, disaster, neglect, abuse, misuse, improper handling or storage by the Buyer. This includes, but is not limited to: water damage, mold in the lenses from improper storage, droppage, modification to the camera, opening the camera body, use of non- IDT cables, or third party accessories, etc. Removal or modification of camera lens mount voids any and all warranties except when the lens mount is replaced by the Buyer with an IDT approved lens mount. Breaking the seal on the camera body is prohibited and voids any and all warranties. Any parts replaced by IDT during warranty repair are the property of
IDT and will not be returned to Buyer.
IDT products are compatible with IDT software, IDT parts, and IDT products only. Use of any software, parts, or products other than IDT or IDT approved software, parts, and products voids any and all warranties.
EXCEPT AS SPECIFICALLY SET FORTH ABOVE, IDT AND ITS LICENSORS MAKES
NO WARRANTIES, CONDITIONS, REPRESENTATION OR TERMS, EXPRESS OR
IMPLIED, WHETHER BY STATUE, COMMON LAW, CUSTOM, USAGE OR
OTHERWISE AS TO THE IDT PRODUCT OR ANY COMPONENT THEREOF,
INCLUDING BUT NOT LIMITED TO NON-INFRINGEMENT OF THIRD PARTY RIGHTS,
INTEGRATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR
ANY PARTICULAR PURPOSE. IDT AND ITS LICENSORS DOES NOT WARRANT THE
PERFORMANCE OR RESULT OF THE IDT PRODUCT.
6b. Third-Party Warranty – IDT does not honor warranty agreements extended by third parties. Only warranty agreements granted by IDT will be honored by IDT.
THE SOLE REMEDY UNDER THIS WARRANTY SHALL BE THE REPAIR,
REPLACEMENT, OR CREDIT FOR DEFECTIVE PARTS AS STATED ABOVE. THIS
WARRANTY IS THE SOLE WARRANTY GIVEN BY IDT AND IS IN LIEU OF ANY
OTHER WARRANTIES EITHER EXPRESS OR IMPLIED. THIS WARRANTY EXTENDS
TO THE BUYER AND IS NON-TRANSFERABLE TO OTHER THIRD PARTIES.
6c. IDT Re-Certified Product Warranty – All Electronic Products that are not possessed by the original Buyer may be sent to an Authorized IDT Service Center for an evaluation fee
8 Users Manual
IDT Camera Specifications of $500. IDT will provide a quotation for the re-certification of the product to existing IDT product specifications at time of repair. The Customer is responsible for all costs associated with such re-certification, such as troubleshooting, diagnosis, repair, test, calibration, and shipping costs. The evaluation fee will be applied to the cost of the recertification if the cost of the re-certification is greater than the evaluation fee. Upon completion of re-certification, customer may be offered an IDT Re-Certified Product
Warranty for an additional cost determined at that time.
“Customer” is defined as an entity who obtained an IDT product by other means than directly from IDT. Product re-certification is only available to a Customer and is limited to a one re-certification per Customer upon a change of ownership. As part of the process,
IDT will register the Product to the new Customer.
An IDT Re-Certified Product Warranty is valid for a period of ninety (90) days for the camera and camera accessories after the warranty is accepted by the Customer. IDT
Re-Certified Product Warranty is not available for Digital Media and Batteries.
6d. Non-Warranty Repair – Product that no longer qualifies for Warranty Repair may be sent to an Authorized IDT Service Center for an evaluation fee of $250. IDT will provide a quotation for the repair of the product. The Customer is responsible for all costs associated with such refurbishment, such as troubleshooting, diagnosis, repair, test, calibration, and shipping costs. The evaluation fee will be applied to the cost of the refurbishment if the cost of the refurbishment is greater than the evaluation fee. Any repaired or replaced product shall be warranted for ninety (90) days after it is received by
Customer. Only the components that were repaired or replaced will be eligible for the 90day period. Any parts replaced by IDT during non-warranty repair are the property of IDT and will not be returned to Customer.
7. RETURNS – Buyers must obtain a Return Merchandise Authorization (RMA) prior to the return of any product. Cameras may only be returned for refund within seven (7) days of original delivery by IDT at shipping address specified by Buyer and with less than 10 hours of run time and pass IDT Inbound Quality Control (IQC). Accessories, except Digital Media and
Batteries, may be returned for refund within seven (7) days of original delivery by IDT at shipping address specified by Buyer and pass IDT IQC.
7a. Factory Seal – If the factory seal on the product has been broken, a return will not be accepted, unless IDT gives specific approval for such a return after evaluation (subject to
$500 evaluation fee) and the returned product is subject to a 25% restocking fee. All equipment must be shipped in as new condition and in the original shipping materials.
Refunds are subject to an evaluation of the merchandise upon receipt at IDT as defined above, in addition to other tests to ascertain condition of returned goods. A refund less the restocking fee will be provided within forty-five (45) days of completion of evaluation of goods at IDT.
7b. Shipping – Buyer is responsible for shipping costs to return product to IDT. For Buyer’s protection, IDT recommends that the Buyer uses a traceable and insurable form of mail for shipment.
7c. Buyer has seven (7) days from the date the RMA is issued to deliver the product to IDT.
All product received seven (7) days after the RMA was issued will not be considered eligible as a return for credit. IDT will return product to Buyer and Buyer will assume all shipping costs.
7d. Dangerous Goods Requirements – Buyer acknowledges that Buyer has been advised of the Dangerous Goods shipping requirements relating to lithium ion batteries. If Buyer’s return includes a lithium ion battery, Buyer agrees to have the battery shipped by a certified shipper of Dangerous Goods. Buyer further agrees not to attempt to ship any lithium ion battery that has been physically damaged. Buyer agrees to indemnify and hold IDT and its employees harmless from any and all liability arising from Buyer’s failure to comply with this provision.
Users Manual 9
IDT Camera Specifications
8. CUSTOMER SOURCE INSPECTION – a fee of $500 will be charged for any order requiring customer source inspection or receipt of goods, at the IDT facility.
No-Trouble Found Inspection Fee – Any product sent to IDT for inspection or evaluation where IDT finds no defects or problems with IDT product will be subject to a No-Trouble
Found Inspection Fee of $500. The No-Trouble Found Inspection policy is in place to encourage the Customer to exhaust all technical support resources before shipping product to
IDT.
9. LIMITATION OF LIABILITY – IN NO EVENT SHALL IDT OR ITS LICENSORS BE
LIABLE TO BUYER FOR ANY INDIRECT, CONSEQUENTIAL, PUNITIVE, INCIDENTAL, OR
SPECIAL DAMAGES, OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF
USE, DATA OR PROFITS (HOWEVER CAUSED AN UNDER ANY THEORY OF LIABILITY),
EVEN IF IDT OR ITS LICENSORS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. IN NO EVENT SHALL IDT’S OR ITS LICENSORS’ LIABILITY FOR A
PRODUCT (WHETHER ASSERTED AS A TORT CLAIM, A CONTRACT CLAIM OR
OTHERWISE) EXCEED THE AMOUNTS PAID TO IDT FOR SUCH PRODUCT. IN
ADDITION, IN NO EVENT SHALL IDT’S LIABILITY FOR ALL CLAIMS ARISING OUT OF OR
RELATING TO THIS ORDER EXCEED $25,000 (TWENTY-FIVE THOUSAND U.S.
DOLLARS). IN NO EVENT WILL IDT OR ITS LICENSORS BE LIABLE FOR COSTS OF
PROCUREMENT OF SUBSTITUTE GOODS BY BUYER. IN NO EVENT SHALL IDT OR ITS
LICENSORS BE LIABLE FOR DAMAGES ARISING OUT OF ANY LATE DELIVERY. THE
LIMITATIONS SET FORTH HEREIN SHALL APPLY TO ALL LIABILITIES THAT MAY ARISE
OUT OF THIRD-PARTY CLAIMS AGAINST BUYER. THESE LIMITATIONS SHALL APPLY
NOTWITHSTANDING ANY FAILURE OF ESSENTIAL PURPOSE OF ANY LIMITED
REMEDY. THE LIMITATION SET FORTH IN THIS SECTION SHALL APPLY WHERE THE
DAMAGES ARISE OUT OF OR RELATED TO THIS AGREEMENT.
10. INDEMNIFICATION – Buyer shall indemnify, defend, and hold IDT and IDT’s officers, agents, other representatives and licensors harmless from all demands, claims, actions, causes of actions, proceedings, suits, assessments, losses, damages, liabilities, settlements, judgments, fines, penalties, interest, costs and expenses incurred (including fees and disbursements of legal counsel) of every kind (i) based upon personal injury or death or injury to property to the extent any of the foregoing is proximately caused Buyer’s misuse of the product or by the negligent or willful acts or omissions by the Buyer, or (ii) based on any breach of this agreement by the Buyer.
11. PROPRIETARY INFORMATION – IDT retains for itself and its licensors all proprietary rights, including without limitation all patent, trademark, trade secret, copyright and other intellectual property rights in and to all IDT designs, manufacturing processes, engineering details, and other data pertaining to any product sold except where the rights have been assigned to pursuant to a written agreement signed by a corporate officer of IDT. The products are offered for sale and sold by IDT on the condition that such sale does not convey any right, express or implied, stated or otherwise, under any intellectual property or manufacturing process. IDT and its licensors expressly reserves all intellectual property rights in the product. Without limited the foregoing, all software included in the products
(including any updates to such software provided to Buyer, if applicable) is licensed to Buyer, not sold, and Buyer shall not transfer any such software apart from the product, or modify, decompile, disassemble or reverse engineer or otherwise attempt to derive the source code of such software.
12. NON-WAIVER – Failure of IDT to insist upon strict performance of any terms and conditions herein shall not be deemed a waiver of any subsequent default of terms and conditions thereof.
13. LAW GOVERNING AND EXCLUSIVE JURISDICTION – This Agreement is to be interpreted in accordance with the laws of the State of Florida, United States of America. The sale of any IDT product to Buyer is considered to have taken place in Leon County, Florida and shall be governed by this Agreement. This Agreement will not be governed by the conflict of law rules or the United Nations Convention on Contracts for the International Sale of Goods, the application of which is expressly excluded. Exclusive jurisdiction for any
10 Users Manual
IDT Camera Specifications dispute arising from the terms and conditions of this Agreement shall be Leon County, Florida and both Buyer and IDT waive all rights to have a dispute brought elsewhere.
14. SEVERABILITY – If any of the terms and conditions of this Agreement is held to be invalid under any applicable statute or rule of law, they are, to that extent, deemed omitted.
15. COMPLETE AGREEMENT - The terms and conditions set forth herein comprise the entire agreement between IDT and the Buyer.
1.2.
Return address
Please contact your local dealer within 7 days to obtain an RMA. Included in the original shipping container is a return shipping label. Product must be returned in its original packaging and shipping container and must be in good working order.
Return address:
Integrated Design Tools, Inc.
1 W Mountain Street, Suite 3
PASADENA CA 91103-3070
United States of America
Attn.: Service Department
T: (+1) 626 794-4649
F: (+1) 626 794-4651
Users Manual 11
IDT Camera Specifications
2.
Precautions
2.1.
Cleaning the sensor
Clean the optical surfaces with filtered, compressed air and glass cleaner or distilled water. Use a cotton swab or lens paper. Do not use alcohol or other solvents as these may damage the optical coating and cements.
2.2.
Laser
Do not focus a laser beam on the sensor directly or by reflection, it can cause permanent damage to the sensor. Any laser powerful enough to produce localized heating at the surface of the sensor will cause damage, even if the camera power is off. Laser-
damaged sensors are NOT covered by the warranty.
2.3.
Disconnect power prior to plugging or unplugging any
We use high-performance connectors on all our products to assure operational integrity and durability: these connectors provide many benefits but are not “hot-swappable”
(cannot be unplugged while powered). Unplugging any connectors while powered has a high likelihood of damaging cameras, lights and related accessories.
12 Users Manual
IDT Camera Specifications
3.
Introduction to the cameras
3.1.
M-series
M3 records continuously at an impressive 520 fps with a full resolution of 1280 x 1024 directly to hard drive. Examples of useful applications of the M3 system include automated industrial uses, such as assembly line malfunction prevention and detection, and scientific uses including sustained observation of microscopic or quick-moving subjects.
With the available accessories, a full M5 system definitely offers the ideal solution for any situation where image sharpness and contrast are imperative, and is specially suited for industrial and scientific scanning.
Users Manual 13
IDT Camera Specifications
3.2.
iN-series
The iNdustrial is a small size, shock and vibration proof, lightweight camera system. The iN8 configuration produces stunning 1600 x 1200 pixel images. It is offered in two speed grades: S1 and S2 to deliver up to 500 fps and 1,000 fps in full resolution respectively.
The camera also features advanced thermal management that does not require the use of fans, and benefits from a sealed (IP68) mechanical package allowing under water operation down to a depth of 1 meter.
14 Users Manual
IDT Camera Specifications
3.3.
Os-series
The Os-series is a new digital high-speed camera designed to operate in the most demanding environments. The salient design feature of the Os are its compact size combined with a wide data bus, making it capable of achieving very high frame rates including transfer speeds to high-capacity solid-state (non-volatile) memory.
Users Manual 15
IDT Camera Specifications
3.4.
Nx-series
16
With 6000 ISO Mono 2000 ISO Color sensitivity, 30-bit pixel depth (color), and High G resistance to shock, the NX-Series is well suited for on-board crash testing, where space is at a premium.
NX4: three speed grades allow customized camera performance. Crash-testing, especially in vehicle, is the quintessential NX4 application. The cameras' compact design allows for use in tight environments or when attached to a bore-scope.
NX5: optimally designed for resolution, the 7 micron array of 2336 x 1728 pixels, powers the 730 fps. This sensor array benefits from improved quantum efficiency from its predecessor to reduce noise without sacrificing light sensitivity or bit depth. This makes the camera well-suited for situations requiring light weight and superb resolving power, such as component testing and microscope imaging. Special opportunities for the NX5 exist in broadcast and cinema, when the small size combined with the 4.0 megapixel resolution provides high definition imaging formats. Two cameras can be used as a compact stereoscopic assembly for 3D applications.
NX8: with a maximum resolution of 1600 x 1200, the NX8 can record up to 4,000 fps.
Combine this with its extremely compact size and High G resistance to shock, it is wellsuited for on-board crash testing, where space is at a premium.
Users Manual
IDT Camera Specifications
3.5.
NX-Air series
With 6000 ISO Mono 2000 ISO Color sensitivity, 30-bit pixel depth (color), High G resistance to shock, and internal battery, the NX-Air series are well suited for on-board crash testing, where space is at a premium.
Users Manual 17
IDT Camera Specifications
3.6.
Y Series
18
With extremely low noise levels and high light sensitivity, Y3 models perform well for those whose needs encompass both detail and speed, such as product testing automobiles and engines.
The Y4 is the most versatile camera system, useful in production and research and development environments. This camera system can be operated in an extended dynamic range (EDR) mode to produce either 11-bit or 12-bit images.
The Y5 surpasses high definition with a 4.0 megapixel sensor capable of 730 fps at full resolution. Variable lens mounts support cinema lenses, as well as those built for Nikon and Canon SLRs. The HDMI output ensures that the image can be monitored at the full resolution before, during and after recording.
New to the Y Series, the Y7 PIV model introduces a universal integrated timing interface.
This allows for synchronization of any illumination sources such as lasers or LEDs.
Together with our standard 200-nanosecond inter-frame time, the camera is perfectly suited for PIV researchers as it decreases PIV system size and cost.
Y8 is our latest breakthrough in Y Series development. Utilizing the next generation of sensor technology, the Y8 provides a maximum resolution of 1600 x 1200 and comes in three speed grades with the capability of recording up to 9,300 fps offering uncompromised speed and performance.
Users Manual
IDT Camera Specifications
3.7.
CC Series
IDT's CrashCam™ with integrated storage: 8GB DDR and optional solid-state non-volatile memory of up to 0.5TB. The CrashCam™ is a rugged, sealed, high G and vibration rated camera product designed for use (not exclusively) in harsh, Automotive testing environments. Latest CMOS sensor technology produces extremely low-noise images with up to 12-bit mono or 36-bit color. Support for several sensor platforms to deliver various resolutions and frame rates. Power supply and break-out cable for easy out-ofthe-box operation are included.
Users Manual 19
IDT Camera Specifications
3.8.
Airborne
IDT Os-Series Version 3 Airborne Camera with integrated storage: 8GB of DDR and optional solid-state non-volatile memory of up to 0.5TB. Latest CMOS sensor technology produces extremely low-noise images with up to 12-bit mono or 36-bit color. Support for several sensor platforms to deliver various resolutions and frame rates. Power supply and break-out cable for easy out-of-the-box operation are included.
20 Users Manual
IDT Camera Specifications
3.9.
XStream PCIe series
The XStream™ is a compact camera designed for use with a computer system. It is an image-streaming camera supported by Linux, MAC OS and Windows operating systems.
It is supplied with an end-user software package as well as the SDK.
The main features are:
streaming.
high-resolution and frame rate.
high sensitivity.
low noise.
Users Manual 21
IDT Camera Specifications
3.10.
Legacy series
The X-Series is the first high-speed camera featuring a CMOS sensor that can support a
double-exposure mode. This mode advance allows two consecutive exposures within a
100-nanosecond interval, a revolution for capturing the motion of objects at ultra-high speeds, as in “Particle Image Velocimetry”. High framing rates are achieved using the partial windowing capability. The X-Series cameras are designed for use in industrial and scientific applications that include machine vision, microscopy, and flow and spray analysis.
The camera is supplied in one basic memory configuration: 4 GB.
The cameras feature a USB 2.0 digital interface and Giga-Ethernet (1000 Mbps) that provides true and easy plug-and-play installation and capabilities at a high-speed rate of transfer to a desktop or laptop computer with a single cable. Also, the readily accessible sync input and output signals quickly integrate the camera with illumination sources, such as laser or strobe light. A video output signal (PAL/NTSC) and IRIG-B are also available.
22 Users Manual
IDT Camera Specifications
HG systems are rugged cameras that can withstand violent forces up to 100 G. They come equipped with an internal battery for memory backup, and feature a synchronization scheme via a hub that has become the standard among many automotive manufacturers.
HG camera designs are ideal for Range, Aerospace, and Ballistics applications due to their rugged build, and their ability to perform in a wide range of environments. Accurate phase synchronization between cameras is easy using GPS signals, even when the cameras are miles apart.
The unique ability to process images via look-up tables (LUT) on the fly allows the system to acquire and download 10 bit dynamic range images at the same fast rate as downloading 8 bit images. Custom look-up tables can also be created for the specific needs of any application.
Current HG models supported by Motion Studio and the SDK are:
Legacy Redlake cameras (HG-2000, CR-2000, HG-TX).
HG-100K, HG-LE, HG-TH.
New HG-XR, HG-XL and HG-CH.
Users Manual 23
IDT Camera Specifications
3.11.
System components
The systems components are listed below.
Camera: IDT cameras are the first high-speed cameras featuring a CMOS sensor capable of supporting double-exposure operation mode. The camera body accepts standard C-mount lenses.
MotionPro X/Y: The USB 2.0 (480 Mbps) cable or Giga-Ethernet (1000 Mbps) provide data and control signals to and from the camera as well as connecting the camera to any USB 2.0 or Ethernet port on a desktop or laptop. The CC, OS, NX, NR
and N series cameras provide only Giga-Ethernet data and control signals and do not have a USB interface.
MotionScope M Digital Interface: This camera interfaces to a computer system via a Full Camera Link™ frame grabber. Currently supported frame grabbers are the
Bitflow Karbon, Dalsa-Coreco X64 Xcelera-CL PX4 and the National Instruments
PCIe-1429.
Xstream: this camera is interfaced with a PCI express version 2.0 (X4) board. An adapter allow the communication through Thunderbolt.
Power Source: The power source provides external power to the camera.
Trigger and Synchronization Connectors: The camera has three BNC connectors for input and output of synchronization signals and triggering. These signals are
CMOS level, and provide a means to synchronize the camera with an external clock or trigger it in relation to a given event. The synchronization signals are generated for every image frame produced.
Software and SDK: operates in Windows 2000, XP, Vista, 7, 8, 10 and MAC OS X environment.
Optical Interface: The standard interface is C-mount. C-to-F and Canon mount converters are available upon request.
3.12.
System accessories
MotionPro Timing Hub: USB 2.0 digital interface, integrated control software with 8 outputs and 2 inputs.
MotionPro Data Acquisition (DAS): USB 2.0 digital interface, integrated control software with 16 analog inputs, 4 analog outputs and 16 digital I/O channels.
3.13.
Package contents
Before beginning the installation process, check that the following items are present in the package. If you are missing any of the items listed below, please contact Integrated
Design Tools, Inc. or your sales representative.
Camera.
I/O USB 2.0 Cable or Ethernet cable.
USB key of Motion Studio software suite and documentation.
Power supply.
Cross-platform Quick Start Guide.
24 Users Manual
IDT Camera Specifications
3.14.
Minimum computer requirements
Operating system: Windows XP, Vista, 7, 8, 8.1 or 10. MAC OS X with Intel processor.
Processor: Intel
RAM: 4 GB.
Hard Disk: 200 GB or greater.
Network: 1000 Mbps Ethernet adapter.
USB: USB 2.0 or 3.0
Frame grabbers for M series: Teledyne-Dalsa Coreco Xcelera-CL PX4, National
Instruments PCIe-1429, EPIX PIXCI E4, Bitflow Karbon.
PCIe card for Xstream camera.
Users Manual 25
IDT Camera Specifications
3.15.
IRIG Support
X cameras support IRIG B-120. The signal should be connected to the Trigger In connector.
Y cameras support the IRIG modes listed below.
Modulated IRIG: A, B, D, E, G, H
Level Shift IRIG: B simple and B differential.
The IRIG signal is detected by an external box docked to the camera and connected to the “Control” 8-pin control LEMO connector. The input IRIG signals come from an external IRIG generator connected to the box.
The module has three LED:
Red: power.
Yellow: IRIG signal is locked
Green: 1 PPS reference signal sent to the camera.
26
LEMO connector for control signals
Input from external IRIG generator
Users Manual
IDT Camera Specifications
3.16.
IRIG-Flash Device
Input from external IRIG generator
LEMO connectors for control signals
The IRIG flash device is an external box that can be connected to the Y cameras via the external 8-pin and 4-pin control LEMO connectors. The device can be easily hooked to the camera. It is provided with a connector for the IRIG generator and it is fully compatible with the Motion Studio software.
Also, it is provided with a smart card slot that can contain a 16 GB SD card (SD-HC), for a direct download of the acquired images.
SD-HC card slot
WARNING: DO NOT CONNECT the control cables between the module and the camera when the camera is powering up. Connect the cables BEFORE powering up the camera or AFTER the power up cycle is completed and the back “Status” light is turned into green.
Users Manual 27
IDT Camera Specifications
3.17.
Camera lens adapter
The cameras are supplied with a standard C-mount. Alternatively, a C to F mount adapter is available to interface with F-mount (Nikon type) lenses. Use Nikon lenses with a tilt/shift capability when imaging at an angle. As an option, mounting hardware for tilt/shift lenses by Canon is also available. Contact your Integrated Design
Tools Inc. sales representative for ordering information.
28 Users Manual
IDT Camera Specifications
3.18.
NX-Air with Wi-Fi Adapter
The NX-Air camera may be shipped with a Wi-Fi adapter and a NETGEAR™ router.
The adapter mounted on the camera has two settings.
1. Client: the camera is connected to the Wi-Fi network through the NETGEAR router.
2. AP: the adapter acts as an access point.
To switch between the two settings, follow the instruction below.
Turn off the NX-Air and disconnect the wireless module.
Remove the Wi-Fi adapter from NX-Air by removing the top four screws.
On the bottom of the Wi-Fi adapter there is a switch. Move it to “AP” for Access Point setting or to “Client” to for the Client settings.
Users Manual 29
IDT Camera Specifications
3.18.1.
Instructions for Client configuration
Make sure the switch underneath the Wi-Fi Adapter is in the middle position labeled client.
Connect the router to your computer via Gigabit Ethernet (Make sure not to plug
Ethernet cable into yellow Internet port on router).
Turn on both the router and camera.
Make sure that jumbo packets on both the camera and computer are disabled.
Once these steps are complete, you should be able to locate your camera in the cameras enumerator list.
30 Users Manual
IDT Camera Specifications
3.18.2.
Instructions for Access Point configuration
Make sure the switch underneath the Wi-Fi Adapter is in the position for AP.
Turn on camera and wireless device.
The Camera will create its own wireless network with a SSID of NXA followed by four digits (example: NXA0001).
Connect to this new network (no password)
Once these steps are complete, you should be able to locate your camera in the cameras enumerator list.
Users Manual 31
IDT Camera Specifications
4.
Product Specifications
4.1.
Camera specifications
4.1.1. M Series
M3 M5
Sensor Type
CFA Pattern
Sensor Size
Array Size
Pixel Size
Aspect ratio
Pixel Depth
Internal clock
Triggers
Sync Input
Sync Output
IRIG
GPS Time Code
HDMI/SDI
Communication
Power requirement
Operating temperature
Size
Approx weight
Shock
Vibration
Battery
Lens Mount
Max fps @ max resolution
Minimum exposure time
Sensitivity ISO (mono)
Sensitivity ISO (color)
Memory/DRAM
520 fps @ 1280x1024
1 µs
3000
1000
PC RAM – 2 GB (Win32), 16 GB
(x64), direct write to disk
CMOS-proprietary
BGGR
15.4 x 12.3 mm
1.3 Megapixels
12x12 µm
5:4
10-bit
72.00 MHz
170 fps @ 2320x1728
1 µs
3000
1000
PC RAM – 2 GB (Win32), 16 GB
(x64), direct write to disk
CMOS- proprietary
GRBG
16.4 x 12.1 mm
4 Megapixels
7 x 7 µm
4:3
10-bit
40.00 MHz
TTL / switch closure
Phase-lock TTL
Frame Sync / Strobe
N/A
N/A
N/A
Full Camera-Link (10 taps 8 bit each)
12 V, 2 A
0-50º C, 32-122º F
See mechanical
0.32 kg / 0.71 lbs
100G
40 G, all axes
N/A
C-mount standard, F optional
32 Users Manual
IDT Camera Specifications
4.1.2. Y series
4.1.2.1. Common specifications
Power requirement
Operating temperature
Memory/DRAM
Sensor type
Pixel Depth
Triggers
Sync Input
Sync Output
IRIG
GPS Time Code
HDMI/SDI
WiFi module
Communication
Approx size
Approx weight
Shock Rating
Vibration Rating
Battery powered operation time
Lens Mount
All models
12V, 6.3 A
-40 º to +50º C (-40 to +122º F)
Internal 8-16-32-64 GB
CMOS-proprietary
10-bit
TTL / switch closure
Phase-lock TTL
Frame Sync / Strobe
Optional
Optional
HDMI 30/60 fps
Optional
Ethernet (100-1000 BaseT) – USB 2.0
See mechanical
3.4 kg / 7.5 lbs
100G – all axes
40G – all axes
Operation and backup up to 1 hour
C-mount standard, F/PL optional
Users Manual 33
IDT Camera Specifications
4.1.2.2. Y3
Max fps @ max res
Minimum exposure time
CFA Pattern
Sensor Size
Array Size
Pixel Size
Aspect ratio
Pixel Depth
4.1.2.3. Y4
Y3-S1
3750 @ 1280x1024
1 µs
GBRG
13.9 x 11.2 mm
1.3 Megapixel
10.85 x 10.85 µm
5:4
10-bit
Max fps @ max res
Minimum exposure time
CFA Pattern
Sensor Size
Array Size
Pixel Size
Aspect ratio
Pixel Depth
Y4-S1
3000 @ 1024x1024
1 µs
GBRG
13.9 x 13.9 mm
1 Megapixels
13.68 x 13.68 µm
1:1
10-bit
Y4-S2
5100 @ 1024x1024
1 µs
GBRG
13.9 x 13.9 mm
1 Megapixel
13.68 x 13.68 µm
1:1
10-bit
Y3-S2
6030 @ 1280x1024
1 µs
GBRG
13.9 x 11.2 mm
1.3 megapixel
10.85 x 10.85 µm
5:4
10-bit
Y4-S3
7000 @ 1024x1024
1 µs
GBRG
13.9 x 13.9 mm
1 megapixel
13.68 x 13.68 µm
1:1
10-bit
4.1.2.4. Y5
Max fps @ max resolution
Minimum exposure time
CFA Pattern
Sensor Size
Array Size
Pixel Size
Aspect ratio
Pixel Depth
Y5
730 fps @ 2560x1920
1 µs
GRBG
16.4 x 12.1 mm
5 Megapixels
7 x 7 µm
4:3
10-bit
34 Users Manual
IDT Camera Specifications
4.1.2.5. Y6
Maximum fps @ max resolution
Minimum exposure time
CFA Pattern
Sensor Size
Array Size
Pixel Size
Aspect ratio
Y6
1150 fps @ 1504x1128
1 µs
GBRG
24.0 x 18.0 mm
1.7 megapixel
16 x 16 µm
4:3
4.1.2.6. Y7
Max fps @ max res
Minimum exposure time
CFA Pattern
Sensor Size
Array Size
Pixel Size
Aspect ratio
Y7-S1
5300 @ 1920x1080
1 µs
GBRG
13.9 x 7.8 mm
2 Megapixels
7.24 x 7.24 µm
16:9
Y7-S2
9000 @ 1920x1080
1 µs
GBRG
13.9 x 7.8 mm
2 Megapixel
7.24 x 7.24 µm
16:9
Y7-S3
12300 @ 1920x1080
1 µs
GBRG
13.9 x 7.8 mm
2 megapixel
7.24 x 7.24 µm
16:9
Users Manual 35
IDT Camera Specifications
4.1.2.7. Y8
Max fps @ max res
Minimum exposure time
CFA Pattern
Sensor Size
Array Size
Pixel Size
Aspect ratio
Y8-S1
4000 @ 1600x1200
1 µs
GBRG
13.9 x 10.4 mm
2 Megapixels
8.68 x 8.68 µm
4:3
Y8-S2
6800 @ 1600x1200
1 µs
GBRG
13.9 x 10.4 mm
2 Megapixel
8.68 x 8.68 µm
4:3
Y8-S3
9300 @ 1600x1200
1 µs
GBRG
13.9 x 10.4 mm
2 megapixel
8.68 x 8.68 µm
4:3
36 Users Manual
IDT Camera Specifications
4.1.3. Os-series
4.1.3.1. Common specifications
Power requirement
Operating temperature
Memory/DRAM
Internal SSD
Sensor type
Pixel Depth
Minimum exposure time
Triggers
Sync Input
Sync Output
IRIG
GPS Time Code
HDMI/SDI
WiFi module
Communication
Approximate size
Approximate weight
Shock Rating
Vibration Rating
Battery powered operation time
Lens Mount
All models
18-36 VDC
-40 º to +50º C (-40 to +122º F)
Internal (8 GB)
256 GB / 512 GB
CMOS-proprietary
12-bit
1 µs (100 ns optional)
TTL/switch closure
Phase-lock TTL
Frame sync/Strobe
Optional
Optional
N/A
N/A
Ethernet (1000 BaseT)
See mechanical
0.69 kg or 1.52 lbs
200G
40G - All axes
Optional
C-mount standard
Users Manual 37
IDT Camera Specifications
4.1.3.2. Os3
Max fps @ max res
CFA Pattern
Sensor Size
Array Size
Pixel Size
Aspect ratio
4.1.3.3. Os4
Os3-S1
3000 @ 1280x1024
GBRG
13.9 x 11.1 mm
1.3 Megapixels
10.85 x 10.85 µm
5:4
Os3-S2
5000 @ 1280x1024
GBRG
13.9 x 11.1 mm
1.3 Megapixels
10.85 x 10.85 µm
5:4
Os3-S3
7000 @ 1280x1024
GBRG
13.9 x 11.1 mm
1.3 Megapixels
10.85 x 10.85 µm
5:4
Max fps @ max res
CFA Pattern
Sensor Size
Array Size
Pixel Size
Aspect ratio
4.1.3.4. Os7
Os4-S1
3000 @ 1024x1024
GBRG
14 x 14 mm
1 Megapixels
13.68 x 13.68 µm
1:1
Os4-S2
4500 @ 1024x1024
GBRG
14 x 14 mm
1 Megapixels
13.68 x 13.68 µm
1:1
Os4-S3
6000 @ 1024x1024
GBRG
14 x 14 mm
1 Megapixels
13.68 x 13.68 µm
1:1
Max fps @ max res
CFA Pattern
Sensor Size
Array Size
Pixel Size
Aspect ratio
Os7-S1 Os7-S2 Os7-S3
1350 @ 1920x1280
GBRG
17.5 x 11.7 mm
2 Megapixels
9.13 x 9.13 µm
3:2
2700 @ 1920x1280
GBRG
17.5 x 11.7 mm
2 Megapixels
9.13 x 9.13 µm
3:2
4200 @ 1920x1280
GBRG
17.5 x 11.7 mm
2 Megapixels
9.13 x 9.13 µm
3:2
38 Users Manual
IDT Camera Specifications
4.1.3.5. Os8
Max fps @ max res
CFA Pattern
Sensor Size
Array Size
Pixel Size
Aspect ratio
4.1.3.6. Os9
Max fps @ max res
CFA Pattern
Sensor Size
Array Size
Pixel Size
Aspect ratio
4.1.3.7. Os10-4K
Max fps @ max res
CFA Pattern
Sensor Size
Array Size
Pixel Size
Aspect ratio
Os8-S1 Os8-S2 Os8-S3
2000 @ 1600x1200
GBRG
13.9 x 10.4 mm
2 Megapixels
8.68 x 8.68 µm
4:3
4000 @ 1600x1200
GBRG
13.9 x 10.4 mm
2 Megapixels
8.68 x 8.68 µm
4:3
8000 @ 1600x1200
GBRG
13.9 x 10.4 mm
2 Megapixels
8.68 x 8.68 µm
4:3
Os9
2500 @ 2560x1440
GRBG
19.2 x 10.8 mm
8 Megapixels
7.5 x 7.5 µm
15:9
Os10-4K
1000 @ 3840x2400
GRBG
17.9 x 11.2 mm
8 Megapixels
4.67 x 4.67 µm
8:5
Users Manual 39
IDT Camera Specifications
4.1.3.8. Os Airborne
Max fps @ max res
CFA Pattern
Sensor Size
Array Size
Pixel Size
Aspect ratio
Os4A
1200 @ 1024x1024
GBRG
14 x 14 mm
1 Megapixels
13.68 x 13.68 µm
1:1
Os7A
1350 @ 1920x1280
GBRG
17.5 x 11.7 mm
2 Megapixels
9.13 x 9.13 µm
3:2
Os8A-S1
1500 @ 1600x1200
GBRG
13.9 x 10.4 mm
2 Megapixels
8.68 x 8.68 µm
4:3
40 Users Manual
IDT Camera Specifications
4.1.4. CC series
4.1.4.1. Common specifications
Power requirement
Operating temperature
Memory/DRAM
Internal SSD
Sensor type
Pixel Depth
Minimum exposure time
Triggers
Sync Input
Sync Output
IRIG
GPS Time Code
HDMI/SDI
WiFi module
Communication
Approximate size
Approximate weight
Shock Rating
Vibration Rating
Battery powered operation time
Lens Mount
All models
18-36 VDC
-40 º to +50º C (-40 to +122º F)
Internal (8 GB)
256 GB / 512 GB
CMOS-proprietary
12-bit
1 µs (100 ns optional)
TTL/switch closure
Phase-lock TTL
Frame sync/Strobe
Optional
Optional
SDI 30/60 fps
Optional
Ethernet (1000 BaseT)
See mechanical
0.69 kg or 1.52 lbs
200G
40G - All axes optional
C-mount standard
Users Manual 41
IDT Camera Specifications
4.1.4.2. CC 1060
Max fps @ max res
CFA Pattern
Sensor Size
Array Size
Pixel Size
Aspect ratio
4.1.4.3. CC 1520 / 1540
Max fps @ max res
CFA Pattern
Sensor Size
Array Size
Pixel Size
Aspect ratio
CC 1060
6000 @ 1024x1024
GBRG
14 x 14 mm
1 Megapixels
13.68 x 13.68 µm
1:1
CC 1520
2000 @ 1440x1024
GBRG
16.7 x 11.9 mm
2 Megapixels
11.60 x 11.60 µm
3:2
CC 1540
4000 @ 1440x1024
GBRG
16.7 x 11.9 mm
2 Megapixels
11.60 x 11.60 µm
3:2
42 Users Manual
IDT Camera Specifications
4.1.4.4. CC 2020
Max fps @ max res
CFA Pattern
Sensor Size
Array Size
Pixel Size
Aspect ratio
4.1.4.5. CC 4010
Max fps @ max res
CFA Pattern
Sensor Size
Array Size
Pixel Size
Aspect ratio
CC2020
2000 @ 1920x1080
GRBG
19.2 x 10.8 mm
2 Megapixels
10 x 10 µm
15:9
CC4010
1000 @ 2560x1600
GRBG
17.9 x 11.2 mm
8 Megapixels
7 x 7 µm
8:5
Users Manual 43
IDT Camera Specifications
4.1.5. NX / NX-Air series
4.1.5.1. Common specifications
Power requirement
Operating temperature
Memory/DRAM
Sensor type
Pixel depth
Triggers
Sync Input
Sync Output
IRIG
GPS Time Code
HDMI/SDI
WiFi module
Communication
Approximate size
Approximate weight
Shock Rating
Vibration Rating
Battery powered operation time
Lens Mount
All models
12 VDC (N, NR, NX)
18-48 VDC (NXA)
-40 º to +50º C (-40 to +122º F)
Internal (1.25, 3, 4, 5 GB)
CMOS-proprietary
10 bit
TTL/switch closure
Phase-lock TTL
Frame sync/Strobe
Optional
Optional
N/A
Optional
Ethernet (100-1000 BaseT)
See mechanical
0.2 kg / 0.5 lbs (NX-NXT)
0.6 kg / 1.5 lbs (NXA)
200G – all axes
40G – all axes
Operation and backup up to 2 hours
C-mount standard, F/PL optional
44 Users Manual
IDT Camera Specifications
4.1.5.2. NX3 (NR3, N3 except weight, size and memory)
NX3-S1 NX3-S2 NX3-S3
Max fps @ max res
Minimum exposure time
CFA Pattern
Sensor Size
Array Size
Pixel Size
Aspect ratio
NX3-S4
500 @
1280x1024
1 µs
1030 @
1280x1024
1 µs
BGGR BGGR
15.4 x 12.3 mm 15.4 x 12.3 mm
1.3 Megapixels 1.3 Megapixels
12x12 µm
5:4
12x12 µm
5:4
2550 fps @
1280x1024
1 µs
3800 fps @
1280x1024
1 µs
GBRG
13.9 x 11.2 mm
1.3 Megapixel
GBRG
13.9 x 11.2 mm
1.3 Megapixel
10.85 x 10.85 µm 10.85 x 10.85 µm
5:4 5:4
4.1.5.3. NX4 (NR4, N4 except weight, size and memory)
NX4-S1 NX4-S2
Max fps @ max res
Minimum exposure time
CFA Pattern
Sensor Size
Array Size
Pixel Size
Aspect ratio
1000 @ 1024x1024
1 µs
GBRG
13.9 x 13.9 mm
1 Megapixels
13.68 x 13.68 µm
1:1
2000 @ 1024x1024
1 µs
GBRG
13.9 x 13.9 mm
1 Megapixel
13.68 x 13.68 µm
1:1
NX4-S3
3000 @ 1024x1024
1 µs
GBRG
13.9 x 13.9 mm
1 megapixel
13.68 x 13.68 µm
1:1
Users Manual 45
IDT Camera Specifications
4.1.5.4. NX5 (NR5, N5 except weight, size and memory)
NX5-S1
Max fps @ max res
Minimum exposure time
CFA Pattern
Sensor Size
Array Size
Pixel Size
Aspect ratio
325 fps @ 2336x1728
1 µs
GRBG
16.4 x 12.1 mm
4 Megapixels
7 x 7 µm
4:3
NX5-S2
730 fps @ 2336x1728
1 µs
GRBG
16.4 x 12.1 mm
4 Megapixels
7 x 7 µm
4:3
4.1.5.5. NX7
Max fps @ max res
Minimum exposure time
CFA Pattern
Sensor Size
Array Size
Pixel Size
Aspect ratio
NX7-S1
2500 @ 1920x1080
1 µs
GBRG
13.9 x 7.8 mm
1 Megapixels
7.24 x 7.24 µm
16:9
NX7-S2
5000 @ 1920x1080
1 µs
GBRG
13.9 x 7.8 mm
1 Megapixel
7.24 x 7.24 µm
16:9
46 Users Manual
IDT Camera Specifications
4.1.5.6. NX8
Max fps @ max res
Minimum exposure time
CFA Pattern
Sensor Size
Array Size
Pixel Size
Aspect ratio
NX8-S1
2000 @ 1600x1200
1 µs
GBRG
13.9 x 10.4 mm
1 Megapixels
8.68 x 8.68 µm
4:3
NX8-S2
4000 @ 1600x1200
1 µs
GBRG
13.9 x 10.4 mm
1 Megapixel
8.68 x 8.68 µm
4:3
Users Manual 47
IDT Camera Specifications
4.1.6. iN series
4.1.6.1. Common specifications
Power requirement
Operating temperature
Memory/DRAM
Sensor type
Pixel depth
Triggers
Sync Input
Sync Output
IRIG
GPS Time Code
HDMI
WiFi module
Communication
Approximate size
Approximate weight
Shock Rating
Vibration Rating
Battery powered operation time
Lens Mount
4.1.6.2. iN8
Max fps @ max res
Minimum exposure time
CFA Pattern
Sensor Size
Array Size
Pixel Size
Aspect ratio
All models
12 VDC
-40 º to +50º C (-40 to +122º F)
Internal (1.25, 3, 4, 5 GB)
CMOS-proprietary
10 bit
TTL/switch closure
Phase-lock TTL
Frame sync/Strobe
Optional
Optional
N/A
Optional
Ethernet (100-1000 BaseT)
See mechanical
0.2 kg / 0.5 lbs (NX-NXT)
0.6 kg / 1.5 lbs (NXA)
200G – all axes
40G – all axes
Operation and backup up to 2 hours
C-mount standard, F/PL optional iN8-S1
500 @ 1600x1200
1 µs
GBRG
13.9 x 10.4 mm
1 Megapixels
8.68 x 8.68 µm
4:3 iN8-S2
1000 @ 1600x1200
1 µs
GBRG
13.9 x 10.4 mm
1 Megapixels
8.68 x 8.68 µm
4:3
48 Users Manual
IDT Camera Specifications
4.1.7. XStream series
Max fps @ max resolution
Minimum exposure time
Memory/DRAM
Sensor Type
CFA Pattern
Sensor Size
Array Size
Pixel Size
Aspect ratio
Pixel Depth
Triggers
Sync Input
Sync Output
IRIG
GPS Time Code
HDMI
Communication
Power requirement
Operating temperature
Size
Approx weight
Battery
Lens Mount
720p 1440p
1700 fps @ 1280x720
1 µs
PC RAM, direct write to disk
450 fps @ 2560x1440
1 µs
PC RAM, direct write to disk
CMOS-proprietary
GRBG
15.4 x 12.3 mm
1.3 Megapixels
12x12 µm
16:9
10-bit
CMOS- proprietary
GRBG
16.1 x 12.1 mm
5 Megapixels
7 x 7 µm
16:9
10-bit
TTL / switch closure
Phase-lock TTL
Frame Sync / Strobe
N/A
N/A
N/A
PCIe Gen 2.0 x4, Thunderbolt 1 and 2
7-12 V, 1 A
Active cooling -40º to +60º C, -40 to +122º F
See mechanical
0.24 kg or 0.53 lbs
N/A
C-mount standard, F optional
Users Manual 49
IDT Camera Specifications
4.2.
Camera back panel
4.2.1. Y series
Two versions of the back panel are available (with SMA or BNC)
SMA Version
The MotionPro Y-series camera back panel is shown below.
GPS (antenna) Trigger In Sync In Sync Out 5 VDC Output
Control
Gigabit Ethernet connector
Power
(12/14 VCD, 10 A)
HDMI output
USB 2.0 connector
50 Users Manual
IDT Camera Specifications
BNC version (older)
The MotionPro Y-series camera back panel is shown below.
Trigger In
And LED
Sync In
And LED
Synch Out
And LED
Control
Gigabit Ethernet connector
Power
(13.5 VCD, 10 A)
HDMI output
USB 2.0 connector
Users Manual 51
IDT Camera Specifications
4-pins Control connector
The Sync/Trigger signals are available through the pins of the Control LEMO Connector.
The connector is located in the central part of the back panel. The signals mapping is listed in the table below:
PIN #
1
2
3
4
Position
Upper-Left
Lower-Left
Type
INPUT
INPUT
Lower-Right OUTPUT
Upper-Right -
8-pins Control connector (cameras with BNC connectors)
The 8 PIN size 1 LEMO connector pin-out is listed below:
PIN 1: upper position close to the red dot.
PIN 2 to 7: counter clockwise from PIN1.
PIN 8: central position.
6
7
4
5
8
PIN #
1
2
3
Signal
+12 VDC
GND
Trigger
Sync In
Sync Out
RX
TX
GPS
Signal
Trigger In
Sync In
Sync Out
Ground
RX and TX are “receive” and “transmit” signals of the internal serial interface.
52 Users Manual
IDT Camera Specifications
8-pins Control connector (cameras with SMA connectors)
6
7
4
5
8
PIN #
1
2
3
Single-ended (5V TTL)
+ 12 VDC
GND
Trigger
Sync In
Sync Out
IRIG
TX
GPS
Differential (RS422/485)
+Trig In
- Trig In
+ Sync In
- Sync In
+ Sync Out
- Sync Out
+ IRIG
- IRIG
Users Manual 53
IDT Camera Specifications
4.2.2. Os series / Airborne / CC series
The back panel of the CC series is shown below.
Video Output (HDSDI)
Camera control Trigger
The back panel of Os series is the same with the only difference being the HDSDI connector.
54 Users Manual
IDT Camera Specifications
4.2.3. NX series
16 pin LEMO B-series Size 2
(Power and signals)
Users Manual 55
IDT Camera Specifications
4.2.4. NX-Air series
GPS Antenna (SMA) Trigger (SMA)
19 pin LEMO M-series
(Camera Interface)
DC Power Jack
(18-48 V, 2 A)
Power switch
On/OFF
56 Users Manual
IDT Camera Specifications
4.2.5. iN series
Integrated LED Output
Camera control
Users Manual 57
IDT Camera Specifications
4.2.6. M series
The MotionScope M-series camera back panel is shown below.
Power LED Power Connector (12 VCD, 1 A)
Camera
Link
Trigger In Sync In Sync Out
58 Users Manual
IDT Camera Specifications
4.2.7. X series
The MotionPro X USB 2.0/Gigabit-Ethernet camera back panel is shown below.
Gigabit Ethernet connector USB-2 connector
Trigger In
And LED
Sync In
And LED
Synch Out
And LED
IRIG B Live Video Output (PAL/NTSC) Power Connector (24 VCD, 1.6 A)
Users Manual 59
IDT Camera Specifications
4.3.
Camera Spectral Response Curves
1.1
1
0.9
0.8
0.7
0.6
3 Series Color
Normalized Spectral Response (Y) versus Wavelength in nm (X)
0.5
0.4
0.3
0.2
0.1
0
375 400 425 450 475 500 525 550 575 600 625 650 675 700 725
1.1
1
0.9
0.8
0.7
0.6
0.5
3 Series Monochrome
Normalized Spectral Response (Y) versus Wavelength in nm (X)
0.4
0.3
0.2
0.1
0
375 400 425 450 475 500 525 550 575 600 625 650 675 700 725 750 775 800 825 850 875 900 925
60 Users Manual
IDT Camera Specifications
1.1
1
0.9
4 Series Color
Normalized Spectral Response (Y) versus Wavelength in nm (X)
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
375 400 425 450 475 500 525 550 575 600 625 650 675 700 725
1.1
1
0.9
0.8
0.7
4 Series Monochrome
Normalized Spectral Response (Y) versus Wavelength in nm (X)
0.6
0.5
0.4
0.3
0.2
0.1
0
375 400 425 450 475 500 525 550 575 600 625 650 675 700 725 750 775 800 825 850 875 900 925
Users Manual 61
IDT Camera Specifications
1.1
1
0.9
0.8
0.7
0.6
0.5
5 Series Color
Normalized Spectral Response (Y) versus Wavelength in nm (X)
0.4
0.3
0.2
0.1
0
375 400 425 450 475 500 525 550 575 600 625 650 675 700 725
1.1
1
0.9
0.8
0.7
0.6
0.5
5 Series Monochrome
Normalized Spectral Response (Y) versus Wavelength in nm (X)
0.4
0.3
0.2
0.1
0
375 400 425 450 475 500 525 550 575 600 625 650 675 700 725 750 775 800 825 850 875 900 925
62 Users Manual
IDT Camera Specifications
4.4.
Intensified X cameras
In the table below, you may find the optical specifications at 20 C and nominal operating conditions.
Parameter
Input diameter
Input window
Cathode sensitivity for white light at 800 nm at 850 nm
Phosphor
Output window
Luminance gain
E.B.I.
Shading
Resolution
Gate-able
Iris delay
Value
17.5 mm min
Glass (AVG)
500 µA/lm min
43 mA/lm min
33 mA/lm min
P46
Fiber-optic
1590 cd/m²/lx min
0.25 µlx max
45 % max
36 lp/mm min
Yes (down to 50 ns)
16.6 ns max
Users Manual 63
IDT Camera Specifications
4.5.
Mechanical and hole mounts (Y series)
4.5.1. Front view
64 Users Manual
IDT Camera Specifications
4.5.2. Back view
Users Manual 65
IDT Camera Specifications
4.5.3. Side view
66 Users Manual
IDT Camera Specifications
4.5.4. Top View
Users Manual 67
IDT Camera Specifications
4.5.5. Bottom view
68 Users Manual
IDT Camera Specifications
4.5.6. Mounting plate
Front View
Side view
Users Manual 69
IDT Camera Specifications
70 Users Manual
IDT Camera Specifications
4.5.7. Top mounting plate
Front view
Users Manual 71
IDT Camera Specifications
Side view
72 Users Manual
IDT Camera Specifications
4.5.8. First revision camera front view
Users Manual 73
IDT Camera Specifications
4.5.9. First Revision camera top view
74 Users Manual
IDT Camera Specifications
4.5.10.
First revision camera side view
Users Manual 75
IDT Camera Specifications
4.6.
Mechanical and hole mounts (OS V3 and CC series)
4.6.1. Front View
76 Users Manual
IDT Camera Specifications
4.6.2. Back view
Users Manual 77
IDT Camera Specifications
4.6.3. Side views
78 Users Manual
IDT Camera Specifications
4.6.4. Top View
Users Manual 79
IDT Camera Specifications
4.6.5. Bottom View
80 Users Manual
IDT Camera Specifications
4.6.6. Front view with fans and battery
Users Manual 81
IDT Camera Specifications
4.6.7. Side view with fans and battery
82 Users Manual
IDT Camera Specifications
4.7.
Mechanical and hole mounts (Os V1 series)
4.7.1. Front View
Users Manual 83
IDT Camera Specifications
4.7.2. Back View
84 Users Manual
IDT Camera Specifications
4.7.3. Side View
Users Manual 85
IDT Camera Specifications
4.7.4. Top View
86 Users Manual
IDT Camera Specifications
4.7.5. Bottom View
Users Manual 87
IDT Camera Specifications
4.8.
Mechanical and hole mounts (NX series)
4.8.1. Front View
88 Users Manual
IDT Camera Specifications
4.8.2. Back View
Users Manual 89
IDT Camera Specifications
4.8.3. Side View
90 Users Manual
IDT Camera Specifications
4.8.4. Top View
Users Manual 91
IDT Camera Specifications
4.8.5. Bottom View
92 Users Manual
IDT Camera Specifications
4.9.
Mechanical and hole mounts (iN series)
4.9.1. Front View
Users Manual 93
IDT Camera Specifications
4.9.2. Back View
94 Users Manual
IDT Camera Specifications
4.9.3. Side View
Users Manual 95
IDT Camera Specifications
4.9.4. Top View
96 Users Manual
IDT Camera Specifications
4.9.5. Bottom View
Users Manual 97
IDT Camera Specifications
4.10.
Mechanical and hole mounts (NX-Air series)
4.10.1.
Front View
98 Users Manual
IDT Camera Specifications
4.10.2.
Back View
Users Manual 99
IDT Camera Specifications
4.10.3.
Side View
100 Users Manual
IDT Camera Specifications
4.10.4.
Top View
Users Manual 101
IDT Camera Specifications
4.10.5.
Bottom View
102 Users Manual
IDT Camera Specifications
4.11.
Mechanical and hole mounts (NX-Air with Wi-Fi module)
4.11.1.
Front View
Users Manual 103
IDT Camera Specifications
4.11.2.
Back View
104 Users Manual
IDT Camera Specifications
4.11.3.
Side View
Users Manual 105
IDT Camera Specifications
4.11.4.
Top View
106 Users Manual
IDT Camera Specifications
4.11.5.
Bottom View
Users Manual 107
IDT Camera Specifications
4.12.
Mechanical and hole mounts (M series)
4.12.1.
Front View
108 Users Manual
IDT Camera Specifications
4.12.2.
Back View
Users Manual 109
IDT Camera Specifications
4.12.3.
Side View
110 Users Manual
IDT Camera Specifications
4.12.4.
Side View with mount
Users Manual 111
IDT Camera Specifications
4.12.5.
Top View
112 Users Manual
IDT Camera Specifications
4.12.6.
Bottom View
Users Manual 113
IDT Camera Specifications
4.12.7.
Bottom View with Mount
114 Users Manual
IDT Camera Specifications
4.13.
Mechanical and hole mounts (XStream)
4.13.1.
Front view
Users Manual 115
IDT Camera Specifications
4.13.2.
Back view
116 Users Manual
IDT Camera Specifications
4.13.3.
Side views
Users Manual 117
IDT Camera Specifications
4.13.4.
Top view
118 Users Manual
IDT Camera Specifications
4.13.5.
Bottom view
Users Manual 119
IDT Camera Specifications
4.14.
Mechanical and hole mounts (NR series)
4.14.1.
Front View (all memory configurations)
120 Users Manual
IDT Camera Specifications
4.14.2.
Back View (all memory configurations)
Users Manual 121
IDT Camera Specifications
4.14.3.
Side View (1.25 GB)
122 Users Manual
IDT Camera Specifications
4.14.4.
Top View (1.25 GB)
Users Manual 123
IDT Camera Specifications
4.14.5.
Bottom View (1.25 GB)
124 Users Manual
IDT Camera Specifications
4.14.6.
Side View (2.5 GB)
Users Manual 125
IDT Camera Specifications
4.14.7.
Top View (2.5 GB)
126 Users Manual
IDT Camera Specifications
4.14.8.
Bottom View (2.5 GB)
Users Manual 127
IDT Camera Specifications
4.14.9.
Side View (5.0 GB)
128 Users Manual
IDT Camera Specifications
4.14.10. Top View (5.0 GB)
Users Manual 129
IDT Camera Specifications
4.14.11. Bottom View (5.0 GB)
130 Users Manual
IDT Camera Specifications
4.15.
Mechanical and hole mounts (N series)
4.15.1.
Front View
Users Manual 131
IDT Camera Specifications
4.15.2.
Back Views
132 Users Manual
IDT Camera Specifications
4.15.3.
Side View
Users Manual 133
IDT Camera Specifications
4.15.4.
Top View
134 Users Manual
IDT Camera Specifications
4.15.5.
Bottom View
Users Manual 135
IDT Camera Specifications
4.16.
Mechanical and hole mounts (X series)
4.16.1.
Top view
136 Users Manual
IDT Camera Specifications
4.16.2.
Bottom view
Users Manual 137
IDT Camera Specifications
4.16.3.
Side view
138 Users Manual
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement