MARTIN® TRAC-MOUNT ™ Impact Cradle

MARTIN® TRAC-MOUNT ™ Impact Cradle
MARTIN®
TRAC-MOUNT ™
Impact Cradle
Go to MARTIN® TRAC_MOUNT™ Impact Cradle web page
Operator’s Manual
M3220
Important
MARTIN ENGINEERING HEREBY DISCLAIMS ANY LIABILITY FOR: DAMAGE DUE TO
CONTAMINATION OF THE MATERIAL; USER’S FAILURE TO INSPECT, MAINTAIN AND TAKE
REASONABLE CARE OF THE EQUIPMENT; INJURIES OR DAMAGE RESULTING FROM USE OR
APPLICATION OF THIS PRODUCT CONTRARY TO INSTRUCTIONS AND SPECIFICATIONS
CONTAINED HEREIN. MARTIN ENGINEERING’S LIABILITY SHALL BE LIMITED TO REPAIR
OR REPLACEMENT OF EQUIPMENT SHOWN TO BE DEFECTIVE.
Observe all safety rules given herein along with owner and Government standards and regulations. Know
and understand lockout/tagout procedures as defined by American National Standards Institute (ANSI)
z244.1-1982, American National Standard for Personnel Protection - Lockout/Tagout of Energy Sources Minimum Safety Requirements and Occupational Safety and Health Administration (OSHA) Federal
Register, Part IV, 29 CFR Part 1910, Control of Hazardous Energy Source (Lockout/Tagout); Final Rule.
The following symbols may be used in this manual:
!
DANGER
Danger: Immediate hazards that will result in severe personal injury or death.
!
WARNING
Warning: Hazards or unsafe practices that could result in personal injury.
!
CAUTION
Caution: Hazards or unsafe practices that could result in product or property damages.
IMPORTANT
Important: Instructions that must be followed to ensure proper installation/operation of equipment.
NOTE
Note: General statements to assist the reader.
Section
Page
List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Impact Cradle materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Materials required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
1
1
Before Installing Impact Cradle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing Impact Cradle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Locating MARTIN® TRAC-MOUNT™ Impact Cradle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disassembling MARTIN® TRAC-MOUNT™ Impact Cradle . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing MARTIN® TRAC-MOUNT™ Impact Cradle under belt . . . . . . . . . . . . . . . . . . . . . .
After Installing Impact Cradle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Weekly Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting/Installation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Part Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
3
Martin Engineering M3220-10/11
i
3
4
5
6
7
8
9
MARTIN® TRAC-MOUNT™ Impact Cradle
Table of Contents
Table of Contents
List of Figures & Tables
List of Figures
Figure
1
2
3
4
5
Title
Page
®
Locating MARTIN TRAC-MOUNT™ Impact Cradle . . . . . . . . . . . . . . . . . . . 3
Installing MARTIN® TRAC-MOUNT™ Impact Cradle . . . . . . . . . . . . . . . . . . . 4
Installing Impact Bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
MARTIN® TRAC-MOUNT™ Impact Cradle Assembly,
P/N 30688-XXXXX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Conveyor Products Warning Label, P/N 23395 . . . . . . . . . . . . . . . . . . . . . . . . . . 13
List of Tables
Table
I
II
Title
Page
MARTIN® TRAC-MOUNT™
Impact Cradle Materials and Specifications . . . . 1
TRAC-MOUNT™ Impact Cradle Assembly
Part Numbers and Quantities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
MARTIN®
Martin Engineering M3220-10/11
ii
MARTIN® TRAC-MOUNT™ Impact Cradle
The MARTIN® TRAC-MOUNT™ Impact Cradle is a layered, shockabsorbing conveyor belt transfer point product engineered for use in bulk
solids handling industries.
General
The MARTIN® GUARDASEALTM Conveyor Belt Support System can be
installed downstream from the MARTIN® TRAC-MOUNT™ Impact Cradle
to provide maximum conveyor belt stability. See “Part Numbers” to order.
Materials and specifications for the MARTIN® TRAC-MOUNT™ Impact
Cradle are shown in Table I.
Impact Cradle
materials
Table I. MARTIN® TRAC-MOUNT™ Impact Cradle Materials and Specifications
Bar With UHMW Top
Coefficient of Friction
0.5
Service Temperature
-20 to 140°F (-29 to 60°C)
Bar
Construction
Characteristics
Bearing Layer
UHMW Polyethylene
Absorption Layer
50-Durometer SBR Rubber
T-Slot
Aluminum
Fasteners
0.5-in. dia. T-Bolts
References
The following documents are referenced in this manual:
• American National Standards Institute (ANSI) z244.1-1982, American
National Standard for Personnel Protection - Lockout/Tagout of Energy
Sources - Minimum Safety Requirements, American National Standards
Institute, Inc., 1430 Broadway, New York, NY 10018.
• Federal Register, Volume 54, Number 169, Part IV, 29 CFR Part 1910,
Control of Hazardous Energy Source (Lockout/Tagout); Final Rule,
Department of Labor, Occupational Safety and Health Administration
(OSHA), 32nd Floor, Room 3244, 230 South Dearborn Street,
Chicago, IL 60604.
Safety
All safety rules defined in the above documents and all owner/employer safety
rules must be strictly followed when working on this equipment.
Materials required
A hoist may be required to install and service this equipment. If a hoist is not
available, impact cradle must be disassembled for installation.
Martin Engineering M3220-10/11
1
MARTIN® TRAC-MOUNT™ Impact Cradle
Introduction
Introduction
Before Installation
Before Installing Impact Cradle
IMPORTANT
The delivery service is responsible for damage occurring in
transit. Martin Engineering CANNOT enter claims for
damages. Contact your transportation agent for more
information.
1. Inspect shipping container for damage. Report damage to delivery service
immediately and fill out delivery service’s claim form. Keep any damaged
goods subject to examination.
2. Remove impact cradle from shipping container. Equipment in container
should include the following:
• MARTIN® TRAC-MOUNT™ Impact Cradle Assembly.
• Two Conveyor Products Warning Labels, P/N 23395.
3. If anything is missing, contact Martin Engineering or a representative.
!
WARNING
Before installing equipment, turn off and lock out/tag out
energy source to conveyor and conveyor accessories.
4. Turn off and lock out/tag out energy source according to ANSI standards
(see “References”).
!
WARNING
If equipment will be installed in an enclosed area, gas level or
dust content must be tested before using a cutting torch or
welding. Using a cutting torch or welding in an area with gas
or dust may cause an explosion.
5. If using a cutting torch or welding, test atmosphere for gas level or dust
content. Cover conveyor belt with fire retardant cover.
6. If not already present, install an impact idler 1 in. (25 mm) ahead of and
1 in. (25 mm) behind impact cradle location.
7. Remove any unnecessary idlers. (The MARTIN® TRAC-MOUNT™
Impact Cradle can replace up to four impact idlers.)
Martin Engineering M3220-10/11
2
MARTIN® TRAC-MOUNT™ Impact Cradle
Installation
Installing Impact Cradle
Center 1.00 (25)
1.00 (25)
.75 (19)
.375 (9)
4
3
2
1
13.50 13.50 13.50
(343) (343) (343)
Figure 1. Locating MARTIN® TRAC-MOUNT™ Impact Cradle
Locating
MARTIN®
TRAC-MOUNT™
Impact Cradle
IMPORTANT
If you can install impact cradle in one piece, do not
disassemble it. Depending on the application, you may have to
lay down one or both wing sections, remove the wing sections,
or completely disassemble the impact cradle for installation.
1. Locate impact cradle on belt.
2. If you do not have a hoist and/or you cannot slide impact cradle under belt
in one piece, disassemble impact cradle.
!
WARNING
Impact cradle is very heavy. When installing in one piece, use
a hoist for lifting unit into place.
3. Install impact cradle under belt.
4. See Figure 1. Make sure chute walls and/or wear liners are correct
distance above belt as shown. If necessary, modify chute walls and/or
wear liners.
5. Locate impact cradle so second I-beam (if space allows) or first I-beam
from tail pulley aligns with center of loading point. Mark center of
loading point on stringer on both sides of belt.
6. Starting from center of loading point mark (second I-beam), make the
following measurements:
a. Measure 13-1/2 in. (343 mm) toward tail pulley and mark location on
stringer (center of first I-beam).
b. Measure 13-1/2 in. (343 mm) away from tail pulley and mark location
on stringer (center of third I-beam).
c. Measure 27 in. (686 mm) away from tail pulley and mark location on
stringer (center of fourth I-beam).
7. Repeat step 6 on other side of belt.
8. Install an idler 1 in. (25 mm) before and 1 in. (25 mm) after impact cradle.
Martin Engineering M3220-10/11
3
MARTIN® TRAC-MOUNT™ Impact Cradle
Installation
*1/2 in. (13mm)
K
F
B
J
A
C
D
A. Hex head cap screw
Flat washer
Compression washer
Hex nut
B. Support arm
C. Hex head cap screw (8)
Flat washer (8)
Compression washer (8)
Hex nut (8)
G
E
H
D. Wing sliding
H. Angle weldment
sleeve weldment
J. Hex head cap screw (16)
E. I-beam
Flat washer (16)
Compression washer (16)
F. Impact bar
Hex nut (16)
G. T-bolt (3)
K. Hex head cap screw (8)
Flat washer (3)
Flat washer (8)
Compression washer (3)
Compression washer (8)
Hex nut (3)
Hex nut (8)
*1/4” (6mm) for flat belts
Figure 2. Installing MARTIN® TRAC-MOUNT™ Impact Cradle (troughed belt shown)
IMPORTANT
Disassembling
MARTIN®
TRAC-MOUNT™
Impact Cradle
Installing
MARTIN®
TRAC-MOUNT™
Impact Cradle
under belt
Martin Engineering M3220-10/11
If you can install impact cradle in one piece, do not
disassemble it. Skip this section.
1. To lay down wing section of impact cradle, remove hex head cap screw,
flat washer, compression washer, and hex nut (A, Figure 2) from each
support arm (B).
2. To remove wing section of impact cradle, remove four hex head cap
screws, flat washers, compression washers, and hex nuts (C) from each
wing sliding sleeve weldment (D). Slide wing section off I-beams (E).
3. To remove center section of impact cradle, remove wing section (see
step 2), then slide angle weldments off I-beams.
1. Slide impact cradle under belt in pre-determined location, and align with
marks for I-beams on both sides of belt.
2. Make sure I-beams are perpendicular to belt, or bars will wear unevenly
and maintenance will be difficult. Make sure center bars are centered
below belt and are parallel to belt travel.
3. Make sure distance from top of center bar to bottom surface of belt
measures 1/2 in. (13 mm) maximum (see Figure 2). If distance is greater
than this, add shims under I-beams to raise impact cradle to height of
adjacent idlers. If distance is less than this, contact Martin Engineering
or a representative.
4
MARTIN® TRAC-MOUNT™ Impact Cradle
NOTE
Martin Engineering recommends bolting rather than welding
I-beams to stringers for easier accessibility and maintenance.
5. Bolt or weld I-beams to stringers as follows:
a. If bolting, drill or cut 9/16-in. holes in stringers through mounting
holes in feet of each I-beam. Install hex head cap screw, flat washer,
compression washer, and hex nut (J, Figure 2) in each hole to secure
I-beams to stringers.
b. If welding, clean stringer of rust and dirt. Then stitch weld I-beams to
stringer.
Belt Direction
Figure 3. Installing Impact Bars
6. If removed for installation, install impact bars and/or wing section(s).
Make sure tapered ends of impact bars are located as shown.
7. To adjust angle of wing section, remove hex head cap screw, flat washer,
compression washer, and hex nut (K) from support arm (B). Lower or
raise wing section to one of three positions. Secure with hex head cap
screw, washers, and hex nut.
Martin Engineering M3220-10/11
5
MARTIN® TRAC-MOUNT™ Impact Cradle
Installation
4. For troughed belts, make sure clearance between belt and wing section is
1/2 in. (13 mm) where wing section meets base, and tapers to no clearance
between belt and wing section at outside edge (as shown in Figure 2).
After Installation
After Installing Impact Cradle
1. Thoroughly wipe outside chute walls clean above impact cradle on both
sides of chute. Place a Conveyor Products Warning Label (P/N 23395) on
each chute wall visible to belt operator.
!
WARNING
Failure to remove tools from installation area and conveyor
belt before turning on energy source can cause serious injury
to personnel and damage to belt.
2. Remove all tools and fire retardant cover from installation area and
conveyor belt.
!
DANGER
Do not touch or go near conveyor belt or conveyor accessories
when conveyor belt is running. Body or clothing can get
caught and pull body into conveyor belt, causing severe injury
or death.
3. Turn on conveyor belt.
!
WARNING
Before adjusting impact cradle, turn off and lock out/tag out
energy source to conveyor belt and conveyor accessories.
4. After 1 hour of operation, turn off and lock out/tag out energy source
according to ANSI standards (see “References”).
5. Make sure all fasteners are tight. Tighten if necessary.
6. Inspect impact bars for wear. (A small amount of “break-in” wear may
be found. This will stop once bars wear to conveyor belt contour.)
7. If excessive wear, uneven wear, or some other problem exists, see
“Troubleshooting/ Installation Checklist.”
Martin Engineering M3220-10/11
6
MARTIN® TRAC-MOUNT™ Impact Cradle
!
WARNING
Before servicing impact cradle, turn off and lock out/tag out
energy source to conveyor belt and conveyor accessories.
1. Turn off and lock out/tag out energy source according to ANSI standards
(see “References”).
2. Make sure all fasteners are tight. Tighten if necessary.
3. Check bars for wear. If light-colored top covering on bars is worn through
to black rubber, replace bars as follows:
a. Remove eight hex head cap screws, flat washers, compression
washers, and hex nuts from wing sliding sleeve weldment.
b. Slide wing sliding sleeve weldment away from belt. Slide center angle
weldments out from under belt.
c. Remove three T-bolts, flat washers, compression washers, and hex
nuts (G, Figure 2) from underneath each impact bar (F).
d. Lift impact bars off angle weldment (H).
e. Install new impact bars, and secure with T-bolts, washers, and
hex nuts.
f. Slide center angle weldments back under belt. Slide wing sliding
sleeve weldment back toward belt, and secure with eight hex head cap
screws, flat washers, compression washers, and hex nuts.
4. Remove fines between impact bars with broom or high-pressure air
or water.
5. Inspect impact cradle for cracks or fatigue. Weld or strengthen structure
as necessary.
6. Remove equipment from service if there is any indication it is not
functioning properly. Call Martin Engineering or representative for
assistance. Do NOT return equipment to operation until the cause of the
problem has been identified and corrected.
7. Wipe warning labels clean. If labels are not readable, contact Martin
Engineering or a representative for replacements.
!
WARNING
Failure to remove tools from maintenance area and conveyor
belt before turning on energy source can cause serious injury
to personnel and damage to belt.
8. Remove all tools from maintenance area.
!
DANGER
Do not touch or go near conveyor belt or conveyor accessories
when conveyor belt is running. Body or clothing can get
caught and pull body into conveyor belt, causing severe injury
or death.
9. Start conveyor belt.
Martin Engineering M3220-10/11
7
MARTIN® TRAC-MOUNT™ Impact Cradle
Maintenance
Weekly Maintenance
Troubleshooting
Troubleshooting/Installation Checklist
Troubleshooting
If you are experiencing problems with impact cradle, see below:
Symptom
Corrective Action
High-impact bar wear rate.
Impact cradle is installed too close to belt.
Make sure impact cradle surface is 1/2 in.
(13 mm) below troughed belt and 1/4 in.
(6 mm) below flat belt.
Impact bars worn unevenly.
Belt is unevenly loaded, wear liners are
improperly installed, and/or impact bars are
not parallel to belt travel. Inspect loading area
and wear liners, and modify transfer point if
necessary.
Installation
checklist
If after taking corrective actions suggested under “Troubleshooting” you are
still experiencing problems, check for the following:
Installation Checklist
✓ Chute walls and/or wear liners are 3/8 in. above belt at tail, and 3/4 in. above belt at head.
✓ Second or first I-beam of impact cradle aligns with center of loading point.
✓ An idler is installed under belt 1 in. (25 mm) before and after impact cradle.
✓ I-beams are perpendicular to belt.
✓ Center impact bars are centered below belt and are parallel to belt travel.
✓ Wing sections are aligned with idlers.
✓ Distance from top of center impact bars to bottom of belt surface is 1/2 in. (13 mm) max. for
troughed belts and 1/4 in. (6 mm) for flat belts.
Martin Engineering M3220-10/11
8
MARTIN® TRAC-MOUNT™ Impact Cradle
This section provides product names and corresponding part numbers for
MARTIN® GUARDABELT™ Impact Cradles. Please reference part
numbers when ordering parts.
MARTIN®
TRAC-MOUNT™
Impact Cradles
MARTIN® TRAC-MOUNT™ Impact Cradle (with 48-in. UHMW bar):
P/N 30688-XXXXX. See Figure 4. First XX indicates belt width in inches;
second XX indicates belt’s trough angle; last X indicates standard cradle (S)
or wide base cradle (W).
MARTIN®
GUARDABELT™
Bars
55-in. UHMW Bar: P/N 32219.
60-in. UHMW Bar: P/N 33816.
MARTIN®
DURT TAMER™
Wear Liners
P/N WL-XXXXXXXXXXXX. First four Xs indicate height of wear liner in
inches; next four Xs indicate length of wear liner in inches; next three Xs
indicate thickness of wear liner in inches; last X indicates wear liner material.
MARTIN®
TRAC-MOUNT™
Support Cradles
MARTIN® TRAC-MOUNT™ Assembly: P/N 36700-XXX
First XX indicates belt width in inches; last X indicates standard cradle (S) or
wide base cradle (W).
Martin Engineering M3220-10/11
9
MARTIN® TRAC-MOUNT™ Impact Cradle
Part Numbers
Part Numbers
Part Numbers
8
7
3
5
6
2
1
19
10
18
4
13
14
16
17
15
12
13
14
11
12
13
14
Figure 4. MARTIN® TRAC-MOUNT™ Impact Cradle Assembly,
P/N 30688-XXXXX* (Sheet 1 of 2)
*First XX = belt width in inches; second XX = trough angle; fifth X = standard base (S) or wide base (W).
Martin Engineering M3220-10/11
10
MARTIN® TRAC-MOUNT™ Impact Cradle
Description
Part No.
Qty
30675-XXXX**
8
1
Wing Sliding Sleeve Weldment
2
Support Arm
Table II
16
3
Hex Head Cap Screw, 3/8”-16NC x 1-1/4” Lg.
12215
16
4
T-Bolt, 1/2”-13NC x 1-1/2” Lg.
31775
Table II
5
Compression Washer, 3/8”
11747
16
6
Hex Nut, 3/8”-16NC
11770
16
7
Impact Bar
31617
Table II
8
Bar Retainer
30683
8
Mount Hardware
31033
1
30654-XXX***
4
9 (NS)
10
I-Beam Weldment
11
Hex Head Cap Screw, 1/2”-13NC x 2” Lg.
14196
16
12
Flat Washer, 1/2”
31010
24
13
Compression Washer, 1/2”
11750
Table II
14
Hex Nut, 1/2”-13NC
11771
Table II
15
Hex Head Cap Screw, 1/2”-13NC x 1-1/2”
11763
8
16
Clevis Pin
30689
8
17
Cotter Pin
30690
8
18
Wing Slide Weldment
Table II
8
19
Angle Weldment
31787
Table II
NS
Label Kit
34042
1
NS
Operator’s Manual
M3220
1
Figure 4.
MARTIN®
TRAC-MOUNT™ Impact Cradle Assembly,
P/N 30688-XXXXX (Sheet 2 of 2)*
*First XX = belt width in inches; second XX = trough angle; fifth X = standard base (S) or
wide base (W).
**First XX = belt width in inches; second XX = trough angle.
***First XX = trough angle; last X = standard base (S) or wide base (W).
NS = Not Shown
Martin Engineering M3220-10/11
11
MARTIN® TRAC-MOUNT™ Impact Cradle
Part Numbers
Item
Part Numbers
Table II. MARTIN® TRAC-MOUNT™ Impact Cradle Assembly
Part Numbers and Quantities
Belt Width
in. (mm)
Assembly
Part No.
Item 2
Part No.
Item 18
Part No.
Items 13 & 14 Items 7 & 19
Qty
Qty
Item 4
Qty
24 (500-600)
30688-2420X
30665-2001
30669-24
42
6
18
30 (650-800)
30688-3020X
30665-2001
30669-24
42
6
18
36 (800-1000)
30688-3620X
30665-2001
30669-24
45
7
21
42 (1000-1200) 30688-4220X
30665-2002
30669-42
51
9
27
48 (1200-1400) 30688-4820X
30665-2002
30669-42
54
10
30
54 (1400-1600) 30688-5420X
30665-2002
30669-42
54
10
30
60 (1600-1800) 30688-6020X
30665-2003
30669-60
63
13
39
72 (1800-2000) 30688-7220X
30665-2003
30669-60
63
13
39
24 (500-600)
30688-2435X
30665-3501
30669-24
42
6
18
30 (650-800)
30688-3035X
30665-3501
30669-24
42
6
18
36 (800-1000)
30688-3635X
30665-3501
30669-24
45
7
21
42 (1000-1200) 30688-4235X
30665-3502
30669-42
51
9
27
48 (1200-1400) 30688-4835X
30665-3502
30669-42
54
10
30
54 (1400-1600) 30688-5435X
30665-3502
30669-42
54
10
30
60 (1600-1800) 30688-6035X
30665-3503
30669-60
63
13
39
72 (1800-2000) 30688-7235X
30665-3503
30669-60
63
13
39
24 (500-600)
30688-2445X
30665-4501
30669-24
42
6
18
30 (650-800)
30688-3045X
30665-4501
30669-24
42
6
18
36 (800-1000)
30688-3645X
30665-4501
30669-24
45
7
21
42 (1000-1200) 30688-4245X
30665-4502
30669-42
51
9
27
48 (1200-1400) 30688-4845X
30665-4502
30669-42
54
10
30
54 (1400-1600) 30688-5445X
30665-4502
30669-42
54
10
30
60 (1600-1800) 30688-6045X
30665-4503
30669-60
63
13
39
72 (1800-2000) 30688-7245X
30665-4503
30669-60
63
13
39
Martin Engineering M3220-10/11
12
MARTIN® TRAC-MOUNT™ Impact Cradle
ON
Lock out and/or tag out all energy sources to
conveyor system and loading system before
performing any work on conveyor or conveyor
accessories. Failure to do so could result in
severe injury or death.
Cierre y/o rotule todas las fuentes de energía al
sistema transportador y al sistema de carga antes
de realizar cualquier trabajo sobre el transportador
o sobre los accesorios del transportador. Si no
se procede asi, puede resultar en heridas serias
o muerte.
Label P/N 23395
Figure 5. Conveyor Products Warning Label, P/N 23395
Martin Engineering M3220-10/11
13
MARTIN® TRAC-MOUNT™ Impact Cradle
Part Numbers
MUCHO
CUIDADO
! WARNING
!
Notes
Any product, process, or technology described here may be the subject of intellectual property rights reserved by
Martin Engineering Company. Trademarks or service marks designated with the ® symbol are registered with the U.S.
Patent and Trademark Office and may be proprietary in one or more countries or regions. Other trademarks and
service marks belonging to Martin Engineering Company in the United States and/or other countries or regions may
be designated with the “TM” and “SM” symbols. Brands, trademarks, and names of other parties, who may or may
not be affiliated with, connected to, or endorsed by Martin Engineering Company, are identified wherever possible.
Additional information regarding Martin Engineering Company’s intellectual property can be obtained at
www.martin-eng.com/trademarks.
Martin Engineering USA
One Martin Place
Neponset, IL 61345-9766 USA
800 544 2947 or 309 852 2384
Fax 800 814 1553
www.martin-eng.com
Form No. M3220-10/11
Subject to change without prior notice.
Quality Management System Certified by DNV - ISO 9001
© Martin Engineering Company 1997, 2011
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising