Maintenance Manual - Alpha SVM/SPM

Maintenance Manual - Alpha SVM/SPM
w
w
w
.g
ef
an
uc
-s
p
ar
Computer Numerical Control Products
ht
tp
://
Alpha Series Motors and Modular Drives
Maintenance Manual
GFZ-65165E/02
/
es
.co
m
GE Fanuc Automation
June 2000
GFL-001
Warning
es
.co
m
/
Warnings, Cautions, and Notes
as Used in this Publication
Warning notices are used in this publication to emphasize that hazardous voltages, currents,
temperatures, or other conditions that could cause personal injury exist in this equipment or may
be associated with its use.
-s
p
Caution
ar
In situations where inattention could cause either personal injury or damage to equipment, a
Warning notice is used.
uc
Caution notices are used where equipment might be damaged if care is not taken.
Note
ef
an
Notes merely call attention to information that is especially significant to understanding and
operating the equipment.
w
.g
This document is based on information available at the time of its publication. While efforts
have been made to be accurate, the information contained herein does not purport to cover all
details or variations in hardware or software, nor to provide for every possible contingency in
connection with installation, operation, or maintenance. Features may be described herein which
are not present in all hardware and software systems. GE Fanuc Automation assumes no
obligation of notice to holders of this document with respect to changes subsequently made.
ht
tp
://
w
w
GE Fanuc Automation makes no representation or warranty, expressed, implied, or statutory
with respect to, and assumes no responsibility for the accuracy, completeness, sufficiency, or
usefulness of the information contained herein. No warranties of merchantability or fitness for
purpose shall apply.
©Copyright 2000 GE Fanuc Automation North America, Inc.
All Rights Reserved.
SAFETY PRECAUTIONS
B-65165E/02
ar
es
.co
m
/
SAFETY PRECAUTIONS
uc
ht
tp
://
w
w
w
.g
ef
3
Contents
DEFINITION OF WARNING, CAUTION, AND NOTE ---FANUC SERVO MOTOR series ---------------------------------2.1 WARNING -------------------------------------------------------2.2 CAUTION --------------------------------------------------------2.3 NOTE--------------------------------------------------------------FANUC SERVO AMPLIFIER series----------------------------3.1 WARNINGS AND CAUTIONS RELATING
TO MOUNTING ------------------------------------------------3.1.1 WARNING -----------------------------------------------3.1.2 CAUTION ------------------------------------------------3.1.3 NOTE------------------------------------------------------3.2 WARNINGS AND CAUTIONS RELATING TO
A PILOT RUN---------------------------------------------------3.2.1 WARNING -----------------------------------------------3.2.2 CAUTION ------------------------------------------------3.3 WARNINGS AND CAUTIONS RELATING
TO MAINTENANCE ------------------------------------------3.3.1 WARNING -----------------------------------------------3.3.2 CAUTION ------------------------------------------------3.3.3 NOTE-------------------------------------------------------
an
1
2
-s
p
This "Safety Precautions" section describes the precautions which
must be observed to ensure safety when using FANUC servo motors
(including spindle motors) and servo amplifiers (including spindle
amplifiers). Users of any servo motor or amplifier model are requested
to read the "Safety Precautions" carefully before using the servo motor
or amplifier.
The users are also requested to read an applicable specification manual
carefully and understand each function of the motor or amplifier for
correct use.
The users are basically forbidden to do any behavior or action not
mentioned in the "Safety Precautions." They are invited to ask FANUC
previously about what behavior or action is prohibited.
s-1
s-2
s-3
s-4
s-7
s-8
s-11
s-12
s-12
s-14
s-16
s-17
s-17
s-18
s-19
s-19
s-21
s-22
B-65165E/02
DEFINITION OF WARNING, CAUTION, AND NOTE
ar
es
.co
m
1
SAFETY PRECAUTIONS
/
1. DEFINITION OF WARNING,
CAUTION, AND NOTE
This manual includes safety precautions for protecting the user and
preventing damage to the machine. Precautions are classified into
Warning and Caution according to their bearing on safety. Also,
supplementary information is described as a Note. Read the Warning,
Caution, and Note thoroughly before attempting to use the machine.
uc
-s
p
WARNING
Applied when there is a danger of the user being
injured or when there is a damage of both the user
being injured and the equipment being damaged if
the approved procedure is not observed.
ef
an
CAUTION
Applied when there is a danger of the equipment
being damaged, if the approved procedure is not
observed.
w
.g
NOTE
The Note is used to indicate supplementary
information other than Warning and Caution.
ht
tp
://
w
w
* Read this manual carefully, and store it in a safe place.
s-2
ar
es
.co
m
FANUC SERVO MOTOR series
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
2
2.FANUC SERVO MOTOR series
/
SAFETY PRECAUTIONS
B-65165E/02
s-3
2.FANUC SERVO MOTOR series
2.1
SAFETY PRECAUTIONS
B-65165E/02
WARNING
Be safely dressed when handling a motor.
Wear safety shoes or gloves when handling a motor as you may
get hurt on any edge or protrusion on it or electric shocks.
-
Use a crane or lift to move a motor from one place to another.
Motors are heavy. When moving them, use a crane or lift as
required. (For the weight of motors, refer to their respective
specification manuals.)
When moving a motor using a crane or lift, use a hanging bolt if
the motor has a corresponding tapped hole, or textile rope if it has
no tapped hole.
If a motor is attached with a machine or any other heavy stuff, do
not use a hanging bolt to move the motor as the hanging bolt
and/or motor may get broken.
When moving a motor, be careful not to apply excessive force to
its windings as the windings may break and/or their insulation
may deteriorate.
-
Do not touch a motor with a wet hand.
A failure to observe this caution is vary dangerous because you
may get electric shocks.
an
Before starting to connect a motor to electric wires, make
sure they are isolated from an electric power source.
A failure to observe this caution is vary dangerous because you
may get electric shocks.
ht
tp
://
w
w
w
.g
ef
-
uc
-s
p
ar
es
.co
m
/
-
-
Do not bring any dangerous stuff near a motor.
Motors are connected to a power line, and may get hot. If a
flammable is placed near a motor, it may be ignited, catch fire, or
explode.
-
Be sure to ground a motor frame.
To avoid electric shocks, be sure to connect the grounding
terminal in the terminal box to the grounding terminal of the
machine.
-
Do not ground a motor power wire terminal or short-circuit it
to another power wire terminal.
A failure to observe this caution may cause electric shocks or a
burned wiring.
(*) Some motors require a special connection such as a winding
changeover. Refer to their respective motor specification
manuals for details.
s-4
SAFETY PRECAUTIONS
2.FANUC SERVO MOTOR series
Connect power wires securely so that they will not get loose.
A failure to observe this caution may cause a wire to be
disconnected, resulting in a ground fault, short circuit, or electric
shock.
-
Do not supply the power to the motor while any terminal is
exposed.
A failure to observe this caution is very dangerous because you
may get electric shocks if your body or any conductive stuff
touches an exposed terminal.
-
Do not get close to a rotary section of a motor when it is
rotating.
A rotating part may catch your cloths or fingers. Before starting a
motor, ensure that there is no stuff that can fly away (such as a
key) on the motor.
-
Before touching a motor, shut off the power to it.
Even if a motor is not rotating, there may be a voltage across the
terminals of the motor.
Especially before touching a power supply connection, take
sufficient precautions.
Otherwise you may get electric shocks.
-s
p
ar
es
.co
m
/
-
Do not touch any terminal of a motor for a while (at least 5
minutes) after the power to the motor is shut off.
High voltage remains across power line terminals of a motor for a
while after the power to the motor is shut off. So, do not touch any
terminal or connect it to any other equipment. Otherwise, you
may get electric shocks or the motor and/or equipment may get
damaged.
-
To drive a motor, use a specified amplifier and parameters.
An incorrect combination of a motor, amplifier, and parameters
may cause the motor to behave unexpectedly. This is dangerous,
and the motor may get damaged.
-
Do not touch a motor when it is running or immediately after
it stops.
A motor may get hot when it is running. Do not touch the motor
before it gets cool enough. Otherwise, you may get burned.
-
Ensure that motors and related components are mounted
securely.
If a motor or its component slips out of place or comes off when
the motor is running, it is very dangerous.
ht
tp
://
w
w
w
.g
ef
-
an
uc
B-65165E/02
s-5
2.FANUC SERVO MOTOR series
B-65165E/02
Be careful not get your hair or cloths caught in a fan.
Be careful especially for a fan used to generate an inward air flow.
Be careful also for a fan even when the motor is stopped, because
it continues to rotate while the amplifier is turned on.
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
ar
es
.co
m
/
-
SAFETY PRECAUTIONS
s-6
SAFETY PRECAUTIONS
B-65165E/02
2.2
2.FANUC SERVO MOTOR series
CAUTION
FANUC motors are designed for use with machines. Do not
use them for any other purpose.
If a FANUC motor is used for an unintended purpose, it may
cause an unexpected symptom or trouble. If you want to use a
motor for an unintended purpose, previously consult with
FANUC.
-
Ensure that a base or frame on which a motor is mounted is
strong enough.
Motors are heavy. If a base or frame on which a motor is mounted
is not strong enough, it is impossible to achieve the required
precision.
-
Be sure to connect motor cables correctly.
An incorrect connection of a cable cause abnormal heat
generation, equipment malfunction, or failure. Always use a
cable with an appropriate current carrying capacity (or thickness).
For how to connect cables to motors, refer to their respective
specification manuals.
-
Ensure that motors are cooled if they are those that require
forcible cooling.
If a motor that requires forcible cooling is not cooled normally, it
may cause a failure or trouble. For a fan-cooled motor, ensure that
it is not clogged or blocked with dust and dirt. For a liquid-cooled
motor, ensure that the amount of the liquid is appropriate and that
the
liquid
piping
is
not
clogged.
For both types, perform regular cleaning and inspection.
-
When attaching a component having inertia, such as a pulley,
to a motor, ensure that any imbalance between the motor and
component is minimized.
If there is a large imbalance, the motor may vibrates abnormally,
resulting in the motor being broken.
-
Be sure to attach a key to a motor with a keyed shaft.
If a motor with a keyed shaft runs with no key attached, it may
impair torque transmission or cause imbalance, resulting in the
motor being broken.
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
ar
es
.co
m
/
-
s-7
2.FANUC SERVO MOTOR series
2.3
SAFETY PRECAUTIONS
B-65165E/02
NOTE
Do not step or sit on a motor.
If you step or sit on a motor, it may get deformed or broken. Do
not put a motor on another unless they are in packages.
-
When storing a motor, put it in a dry (non-condensing) place
at room temperature (0 to 40 5C).
If a motor is stored in a humid or hot place, its components may
get damaged or deteriorated. In addition, keep a motor in such a
position that its shaft is held horizontal and its terminal box is at
the top.
-
Do not remove a nameplate from a motor.
If a nameplate comes off, be careful not to lose it. If the nameplate
is lost, the motor becomes unidentifiable, resulting in
maintenance becoming impossible.
For a nameplate for a built-in spindle motor, keep the nameplate
with the spindle.
-
Do not apply shocks to a motor or cause scratches to it.
If a motor is subjected to shocks or is scratched, its components
may be adversely affected, resulting in normal operation being
impaired. Be very careful when handling plastic portions, sensors,
and windings, because they are very liable to break. Especially,
avoid lifting a motor by pulling its plastic portion, winding, or
power cable.
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
ar
es
.co
m
/
-
-
Do not conduct dielectric strength or insulation test for a
detector.
Such a test can damage elements in the detector.
-
When testing the winding or insulation resistance of a motor,
satisfy the conditions stipulated in IEC34.
Testing a motor under a condition severer than those specified in
IEC34 may damage the motor.
-
Do not disassemble a motor.
Disassembling a motor may cause a failure or trouble in it.
If disassembly is in need because of maintenance or repair, please
contact a service representative of FANUC.
-
Do not modify a motor.
Do not modify a motor unless directed by FANUC. Modifying a
motor may cause a failure or trouble in it.
s-8
SAFETY PRECAUTIONS
2.FANUC SERVO MOTOR series
-
Use a motor under an appropriate environmental condition.
Using a motor in an adverse environment may cause a failure or
trouble in it.
Refer to their respective specification manuals for details of the
operating and environmental conditions for motors.
-
Do not apply a commercial power source voltage directly to a
motor.
Applying a commercial power source voltage directly to a motor
may result in its windings being burned. Be sure to use a specified
amplifier for supplying voltage to the motor.
-
For a motor with a terminal box, make a conduit hole for the
terminal box in a specified position.
When making a conduit hole, be careful not to break or damage
unspecified portions.
Refer to an applicable specification manual.
-
Before using a motor, measure its winding and insulation
resistances, and make sure they are normal.
Especially for a motor that has been stored for a prolonged period
of time, conduct these checks. A motor may deteriorate
depending on the condition under which it is stored or the time
during which it is stored. For the winding resistances of motors,
refer to their respective specification manuals, or ask FANUC.
For insulation resistances, see the following table.
ef
an
uc
-s
p
ar
es
.co
m
/
B-65165E/02
To use a motor as long as possible, perform periodic
maintenance and inspection for it, and check its winding and
insulation resistances.
Note that extremely severe inspections (such as dielectric strength
tests) of a motor may damage its windings. For the winding
resistances of motors, refer to their respective specification
manuals, or ask FANUC. For insulation resistances, see the
following table.
ht
tp
://
w
w
w
.g
-
s-9
2.FANUC SERVO MOTOR series
SAFETY PRECAUTIONS
B-65165E/02
ar
es
.co
m
/
MOTOR INSULATION RESISTANCE MEASUREMENT
Measure an insulation resistance between each winding and
motor frame using an insulation resistance meter (500 VDC).
Judge the measurements according to the following table.
Insulation
resistance
Judgment
100MΩ or
higher
10 to 100 MΩ
Acceptable
The winding has begun deteriorating. There is no
problem with the performance at present. Be sure to
perform periodic inspection.
The winding has considerably deteriorated. Special
care is in need. Be sure to perform periodic
inspection.
Unacceptable. Replace the motor.
1 to 10 MΩ
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
Lower than 1
MΩ
s - 10
ar
es
.co
m
FANUC SERVO AMPLIFIER series
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
3
/
SAFETY PRECAUTIONS
B-65165E/02
3. FANUC SERVO AMPLIFIER
series
s - 11
3. FANUC SERVO AMPLIFIER
series
SAFETY PRECAUTIONS
B-65165E/02
WARNINGS AND CAUTIONS RELATING TO MOUNTING
3.1.1
WARNING
ar
es
.co
m
/
3.1
Check the specification code of the amplifier.
Check that the delivered amplifier is as originally ordered.
-
Mount a ground fault interrupter.
To guard against fire and electric shock, fit the factory power
supply or machine with a ground fault interrupter (designed for
use with an inverter).
-
Securely ground the amplifier.
Securely connect the ground terminal and metal frame of the
amplifier and motor to a common ground plate of the power
magnetics cabinet.
-
Be aware of the weight of the amplifier and other
components.
Control motor amplifiers and AC reactors are heavy. When
transporting them or mounting them in the cabinet, therefore, be
careful not to injured yourself or damage the equipment. Be
particularly carefull not to jam your fingers between the cabinet
and amplifier.
ef
an
uc
-s
p
-
Never ground or short-circuit either the power supply lines or
power lines.
Protect the lines from any stress such as bending. Handle the ends
appropriately.
-
Ensure that the power supply lines, power lines, and signal
lines are securely connected.
A loose screw, loose connection, or the like will cause a motor
malfunction or overheating, or a ground fault.
-
Insulate all exposed parts that are charged.
-
Never touch the regenerative discharge resistor or radiator
directly.
The surface of the radiator and regenerative discharge unit
become extremely hot. Never touch them directly. An
appropriate structure should also be considered.
-
Close the amplifier cover after completing the wiring.
Leaving the cover open presents a danger of electric shock.
-
Do not disassemble the amplifier.
ht
tp
://
w
w
w
.g
-
s - 12
SAFETY PRECAUTIONS
B-65165E/02
3. FANUC SERVO AMPLIFIER
series
Ensure that the cables used for the power supply lines and
power lines are of the appropriate diameter and temperature
ratings.
-
Do not apply an excessively large force to plastic parts.
If a plastic section breaks, it may cause internal damage, thus
interfering with normal operation. The edge of a broken section is
likely to be sharp and, therefore, presents a risk of injury.
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
ar
es
.co
m
/
-
s - 13
3. FANUC SERVO AMPLIFIER
series
B-65165E/02
CAUTION
Do not step or sit on the amplifier.
Also, do not stack unpacked amplifiers on top of each other.
-
Use the amplifier in an appropriate environment.
See the allowable ambient temperatures and other requirements,
given in the corresponding descriptions.
-
Protect the amplifier from corrosive or conductive mist or
drops of water.
Use a filter if necessary.
-
Protect the amplifier from impact.
Do not place anything on the amplifier.
-
Do not block the air inlet to the radiator.
A deposit of coolant, oil mist, or chips on the air inlet will result in
a reduction in the cooling efficiency. In some cases, the required
efficiency cannot be achieved. The deposit may also lead to a
reduction in the useful life of the semiconductors. Especially,
when outside air is drawn in, mount filters on both the air inlet and
outlet. These filters must be replaced regularly.
So, an easy-to-replace type of filter should be used.
-s
p
ar
es
.co
m
/
-
Before connecting the power supply wiring, check the supply
voltage.
Check that the supply voltage is within the range specified in this
manual, then connect the power supply lines.
-
Ensure that the combination of motor and amplifier is
appropriate.
-
Ensure that valid parameters are specified.
Specifying an invalid parameter for the combination of motor and
amplifier may not only prevent normal operation of the motor but
also result in damage to the amplifier.
-
Ensure that the amplifier and peripheral equipment are
securely connected.
Check that the magnetic contactor, circuit breaker, and other
devices mounted outside the amplifier are securely connected to
each other and that those devices are securely connected to the
amplifier.
-
Check that the amplifier is securely mounted in the power
magnetics cabinet.
If any clearance is left between the power magnetics cabinet and
the surface on which the amplifier is mounted, dust entering the
gap may build up and prevent the normal operation of the
amplifier.
ht
tp
://
w
w
w
.g
ef
-
an
uc
3.1.2
SAFETY PRECAUTIONS
s - 14
SAFETY PRECAUTIONS
B-65165E/02
Apply appropriate countermeasures against noise.
Adequate countermeasures against noise are required to maintain
normal operation of the amplifier. For example, signal lines must
be routed away from power supply lines and power lines.
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
ar
es
.co
m
/
-
3. FANUC SERVO AMPLIFIER
series
s - 15
3. FANUC SERVO AMPLIFIER
series
B-65165E/02
NOTE
Keep the nameplate clearly visible.
-
Keep the legend on the nameplate clearly visible.
-
After unpacking the amplifier, carefully check for any
damage.
-
Mount the amplifier in a location where it can be easily
accessed periodic inspection and daily maintenance.
-
Leave sufficient space around the machine to enable
maintenance to be performed easily.
Do not place any heavy objects such that they would interfere
with the opening of the doors.
-
Keep the parameter table and spare parts at hand.
Also, keep the specifications at hand. These items must be stored
in a location where they can be retrieved immediately.
-
Provide adequate shielding.
A cable to be shielded must be securely connected to the ground
plate, using a cable clamp or the like.
uc
-s
p
ar
es
.co
m
/
-
ht
tp
://
w
w
w
.g
ef
an
3.1.3
SAFETY PRECAUTIONS
s - 16
SAFETY PRECAUTIONS
B-65165E/02
3. FANUC SERVO AMPLIFIER
series
WARNINGS AND CAUTIONS RELATING TO A PILOT RUN
3.2.1
WARNING
ar
es
.co
m
/
3.2
Before turning on the power, check that the cables connected
to the power magnetics cabinet and amplifier, as well as the
power lines and power supply lines, are securely connected.
Also, check that no lines are slack.
-
Before turning on the power, ensure that the power magnetics
cabinet is securely grounded.
-
Before turning on the power, check that the door of the power
magnetics cabinet and all other doors are closed.
Ensure that the door of the power magnetics cabinet containing
the amplifier, and all other doors, are securely closed. During
operation, all doors must be closed and locked.
-
Apply extreme caution if the door of the power magnetics
cabinet or another door must be opened.
Only a person trained in the maintenance of the corresponding
machine or equipment should open the door, and only after
shutting off the power supply to the power magnetics cabinet (by
opening both the input circuit breaker of the power magnetics
cabinet and the factory switch used to supply power to the
cabinet). If the machine must be operated with the door open to
enable adjustment or for some other purpose, the operator must
keep his or her hands and tools well away from any dangerous
voltages. Such work must be done only by a person trained in the
maintenance of the machine or equipment.
w
.g
ef
an
uc
-s
p
-
When operating the machine for the first time, check that the
machine operates as instructed.
To check whether the machine operates as instructed, first specify
a small value for the motor, then increase the value gradually. If
the motor operates abnormally, perform an emergency stop
immediately.
-
After turning on the power, check the operation of the
emergency stop circuit.
Press the emergency stop button to check that the motor stops
immediately, and that the power being supplied to the amplifier is
shut off by the magnetic contactor.
-
Before opening a door or protective cover of a machine to
enable adjustment of the machine, first place the machine in
the emergency stop state and check that the motor has
stopped.
ht
tp
://
w
w
-
s - 17
3. FANUC SERVO AMPLIFIER
series
B-65165E/02
CAUTION
-
Note whether an alarm status relative to the amplifier is
displayed at power-up or during operation.
If an alarm is displayed, take appropriate action as explained in
the maintenance manual. If the work to be done requires that the
door of the power magnetics cabinet be left open, the work must
be carried out by a person trained in the maintenance of the
machine or equipment. Note that if some alarms are forcibly reset
to enable operation to continue, the amplifier may be damaged.
Take appropriate action according to the contents of the alarm.
-
Before operating the motor for the first time, mount and
adjust the position and speed detectors.
Following the instructions given in the maintenance manual,
adjust the position and speed detectors for the spindle so that an
appropriate waveform is obtained.
If the detectors are not properly adjusted, the motor may not rotate
normally or the spindle may fail to stop as desired.
-
If the motor makes any abnormal noise or vibration while
operating, stop it immediately.
Note that if operation is continued in spite of there being some
abnormal noise or vibration, the amplifier may be damaged. Take
appropriate corrective action, then resume operation.
ef
an
uc
-s
p
ar
es
.co
m
/
3.2.2
SAFETY PRECAUTIONS
Observe the ambient temperature and output rating
requirements.
The continuous output rating or continuous operation period of
some amplifiers may fall as the ambient temperature increases. If
the amplifier is used continuously with an excessive load applied,
the amplifier may be damaged.
ht
tp
://
w
w
w
.g
-
s - 18
SAFETY PRECAUTIONS
B-65165E/02
3. FANUC SERVO AMPLIFIER
series
WARNINGS AND CAUTIONS RELATING TO MAINTENANCE
3.3.1
WARNING
ar
es
.co
m
/
3.3
Read the maintenance manual carefully and ensure that you
are totally familiar with its contents.
The maintenance manual describes daily maintenance and the
procedures to be followed in the event of an alarm being issued.
The operator must be familiar with these descriptions.
-
Notes on replacing a fuse or PC board
1) Before starting the replacement work, ensure that the circuit
breaker protecting the power magnetics cabinet is open.
2) Check that the red LED that indicates that charging is in
progress is not lit.
The position of the charging LED on each model of amplifier
is given in this manual. While the LED is lit, hazardous
voltages are present inside the unit, and thus there is a danger
of electric shock.
3) Some PC board components become extremely hot. Be
careful not to touch these components.
4) Ensure that a fuse having an appropriate rating is used.
5) Check the specification code of a PC board to be replaced. If
a modification drawing number is indicated, contact FANUC
before replacing the PC board.
Also, before and after replacing a PC board, check its pin
settings.
6) After replacing the fuse, ensure that the screws are firmly
tightened. For a socket-type fuse, ensure that the fuse is
inserted correctly.
7) After replacing the PC board, ensure that it is securely
connected.
8) Ensure that all power lines, power supply lines, and
connectors are securely connected.
-
Take care not to lose any screws.
When removing the case or PC board, take care not to lose any
screws. If a screw is lost inside the nit and the power is turned on,
the machine may be damaged.
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
-
s - 19
3. FANUC SERVO AMPLIFIER
series
SAFETY PRECAUTIONS
B-65165E/02
Notes on replacing the battery of the absolute pulse coder
Replace the battery only while the power is on. If the battery is
replaced while the power is turned off, the stored absolute
positioning data will be lost. Some series servo amplifier
modules have batteries in their servo amplifiers. To replace the
battery of any of those models, observe the following procedure:
Open the door of the power magnetics cabinet; Leave the control
power of the power supply module on; Place the machine in the
emergency stop state so that the power being input to the amplifier
is shut off; Then, replace the battery. Replacement work should
be done only by a person who is trained in the related maintenance
and safety requirements. The power magnetics cabinet in which
the servo amplifier is mounted has a high-voltage section. This
section presents a severe risk of electric shock.
-
Check the number of any alarm.
If the machine stops upon an alarm being issued, check the alarm
number. Some alarms indicate that a component must be replaced.
If the power is reconnected without first replacing the failed
component, another component may be damaged, making it
difficult to locate the original cause of the alarm.
-
Before resetting an alarm, ensure that the original cause of
the alarm has been removed.
an
Contact FANUC whenever
maintenance arises.
ef
-
uc
-s
p
ar
es
.co
m
/
-
question
relating
to
Notes on removing the amplifier
Before removing the amplifier, first ensure that the power is shut
off. Be careful not to jam your fingers between the power
magnetics cabinet and amplifier.
ht
tp
://
w
w
w
.g
-
a
s - 20
SAFETY PRECAUTIONS
B-65165E/02
CAUTION
-
Ensure that all required components are mounted.
When replacing a component or PC board, check that all
components, including the snubber capacitor, are correctly
mounted. If the snubber capacitor is not mounted, for example,
the IPM will be damaged.
-
Tighten all screws firmly.
-
Check the specification code of the fuse, PC board, and other
components.
When replacing a fuse or PC board, first check the specification
code of the fuse or PC board, then mount it in the correct position.
The machine will not operate normally if a fuse or PC board
having other than the correct specification code is mounted, or if
a fuse or PC board is mounted in the wrong position.
-
Mount the correct cover.
The cover on the front of the amplifier carries a label indicating a
specification code. When mounting a previously removed front
cover, take care to mount it on the unit from which it was
removed.
Notes on cleaning the heat sink and fan
1) A dirty heat sink or fan results in reduced semiconductor
cooling efficiency, which degrades reliability. Periodic
cleaning is necessary.
2) Using compressed air for cleaning scatters the dust. A
deposit of conductive dust on the amplifier or peripheral
equipment will result in a failure.
3) To clean the heat sink, do so only after turning the power off
and ensuring that the heat sink has cooled to room
temperature. The heat sink becomes extremely hot, such that
touching it during operation or immediately after power-off
is likely to cause a burn. Be extremely careful when
touching the heat sink.
ht
tp
://
w
w
w
.g
ef
-
an
uc
-s
p
ar
es
.co
m
/
3.3.2
3. FANUC SERVO AMPLIFIER
series
s - 21
3. FANUC SERVO AMPLIFIER
series
B-65165E/02
NOTE
-
Ensure that the battery connector is correctly inserted.
If the power is shut off while the battery connector is not
connected correctly, the absolute position data for the machine
will be lost.
-
Store the manuals in a safe place.
The manuals should be stored in a location where they can be
accessed immediately it so required during maintenance work.
-
Notes on contacting FANUC
Inform FANUC of the details of an alarm and the specification
code of the amplifier so that any components required for
maintenance can be quickly secured, and any other necessary
action can be taken without delay.
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
ar
es
.co
m
/
3.3.3
SAFETY PRECAUTIONS
s - 22
PREFACE
B-65165E/02
PREFACE
/
Organization of Parts I and II
ar
es
.co
m
This manual describes information necessary to maintain FANUC
servo amplifier α series products, such as a power supply module,
servo amplifier module, and spindle amplifier module.
Part I explains the start-up procedure, and part II focuses on
troubleshooting.
The abbreviations listed below are used in this manual.
Abbreviations
FS0-TC
FS0-MC
FS15i, FS15
FS16i, FS16
FS18i, FS18
FS20
FS21i, FS21
PM-E
PM-D
PM-F
PSM
SVM
SPM
ef
an
uc
-s
p
Product name
FANUC Series 0-TC
FANUC Series 0-MC
FANUC Series 15i, 15
FANUC Series 16i, 16
FANUC Series 18i, 18
FANUC Series 20
FANUC Series 21i, 21
FANUC Power Mate-MODEL E
FANUC Power Mate-MODEL D
FANUC Power Mate-MODEL F
Power Supply Module
Servo Amplifier Module
Spindle Amplifier Module
w
w
Series 15i, 15
w
.g
* In this manual, the parameter numbers of servo parameters are
sometimes indicated without CNC product names as follows:
ht
tp
://
Series 16i, 18i, 21i,
16, 18, 20, 21 Power Mate MODEL D, F
Series 0C
1877
8x62
2062
1062
Servo parameter function name or bit
Overload protection coefficient (OVC1)
Power Mate MODEL E
* The manuals shown below provide information related to this
manual. This manual may refer you to these manuals.
1) FANUC SERVO AMPLIFIER α series Descriptions
B-65162E
2) FANUC AC SERVO MOTOR α series Parameter Manual
B-65150E
3) FANUC AC SPINDLE MOTOR α series Parameter Manual
B-65160E
p-1
Table of Contents
B-65165E/02
/
Table of Contents
ar
es
.co
m
SAFETY PRECAUTIONS.................................................................. s - 1
PREFACE ......................................................................................... p - 1
I. START-UP PROCEDURE
OVERVIEW...................................................................................................................3
2
CONFIGURATIONS......................................................................................................4
2.1
2.2
-s
p
1
CONFIGURATIONS......................................................................................................................... 5
MAJOR COMPONENTS.................................................................................................................. 7
uc
α
α
an
!
" !
#
ef
# "
# α
$
"
START-UP PROCEDURE ..........................................................................................23
3.1
START-UP PROCEDURE (OVERVIEW) ...................................................................................... 24
3.2
CONNECTING THE POWER........................................................................................................ 25
w
w
3
w
.g
" %$
&$'
# ()
' *+)
!$*
($$!,+)
# (
! *!
!
. /
## ! *+)
. %$!0 !
!
+)$!$!)
+)
1
$'$*
(
! /
SETTING THE PRINTED-CIRCUIT BOARD................................................................................. 27
://
3.3
ht
tp
## ### ### α
$
### α
$
#
#### α(
$
( #
3.4
4
## 2
INITIALIZING SERVO PARAMETERS .......................................................................................... 31
CONFIRMATION OF THE OPERATION ....................................................................32
4.1
POWER SUPPLY MODULE .......................................................................................................... 33
" ()
'+
$, +)
!
!&$ #"
Table of Contents
B-65165E/02
" 3 #"
" #" ()
' *+)
!$*
#-
/
"# ()
' *+)
!$!1
#/
ar
es
.co
m
"# 33$ #/
"# 4 #
"" +)
01156
,7 $!0, #2
"- ()
' *%8)$!9
+)
%&
*!)
, #
4.2
SERVO AMPLIFIER MODULE ...................................................................................................... 40
" ()
' &$ "
" ()
' *+)
++:6$ "/
"# 46;,%%$0 $!
!)
(7(
"
"" ()
'&$ "2
SPINDLE AMPLIFIER MODULE ................................................................................................... 49
-s
p
4.3
"# ++:6$ -
"# +<
)! *$!!$! -
"# +)
01156
$! -
uc
"# +)
++:$< ' *!)== -
"## +)
!
!! -
!<
<!$ -
an
"#" $
"#- 8)
!! * !
3!)
<$!
3$' * -#
"#/ )!) ! *-#
ef
"# (!! *
$'
$
$! >
$! -"
"## !$!50 $! % ! --
w
.g
"#" ()
' *+)
%
<$'* $8$
-2
"#" /
"#" ?$ &?
/
"#"# ?
α-/&2//&#
$! /
w
w
"#"" *)
! $* !
/#
"#- ()
'&$ /
"#- )
'<$
$! /
"#- ()
'<$
! /2
://
"#-# ()
'!
$!!* $ /
"#/ ,<
*6$!$: *!)
()
'&$ ht
tp
"#/ ,
"#/ $@)$$!
! "#/# ,<
$! !) "#/" *$!$!<
!
#
"#/- ! $ !$$
"
"#// ! $ !$$
( "#/ !!! *!)
!
$$!$!)
$ /
"#/2 6$!$ <
2
"#/ 5A$
! *$!$ 2#
Table of Contents
B-65165E/02
5
PERIODIC MAINTENANCE OF SERVO AMPLIFIER ................................................84
5.1
BATTERY FOR THE ABSOLUTE PULSE CODER....................................................................... 85
- 0 !$ *$
$1!)&$!!
!)
!) 2/
-# (
ar
es
.co
m
/
- : *$&$!!
($
/&/-9/
!) 2
! *$&$!!
!!
22
-" 4
$ *!)
&$!!
-- !!$) *$ 6
!$) *(
! II. TROUBLESHOOTING
1
OVERVIEW.................................................................................................................97
2
ALARM NUMBERS AND BRIEF DESCRIPTIONS ....................................................98
2.2
FOR SERIES 15i ......................................................................................................................... 102
2.3
FOR SERIES 16, 18, 20, 21 ........................................................................................................ 105
2.4
FOR SERIES 15 .......................................................................................................................... 108
2.5
FOR SERIES 0-C......................................................................................................................... 112
uc
-s
p
FOR SERIES 16i, 18i, 20i, 21i, AND Power Mate i....................................................................... 99
TROUBLESHOOTING AND ACTION.......................................................................115
3.1
an
3
2.1
POWER SUPPLY MODULE ........................................................................................................ 116
ef
# 3 /
# $
/
w
.g
# $
## $
# #" $
" 2
#- $
- 2
w
w
#/ $
/ 2
# $
# # $
://
# $
## $
# ht
tp
#" $
" #- $
- #/ $
/ # $
/ #2 $
/ # $
#/ # $
"/ # $
# $
#
## $
2 #
#
Table of Contents
B-65165E/02
#" $
2 #
#- $
"
#/ $
"
/
# $
"
ar
es
.co
m
## 4 -
## $
## $
" ### $
- /
##" $
/ /
##- $
/
##/ $
2 3.2
SERVO AMPLIFIER MODULE .................................................................................................... 128
# < $(
!$2333<3(33$ 5 !)
156$ 2
# 0$2333<3(33$ 5 !)
156$B !
!)
$
$
-s
p
!$ !)$
#
## ( !
: !$*
$ !)
156$ #
#" 6(1 ': !$*
$- !)
156$ #
uc
#- %$ !
$ !)
156$ #
#/ (
!( 5$ #
SERVO SOFTWARE ................................................................................................................... 133
an
3.3
## @!
!
##
## 6$* ###" %
<$'6
ef
### ,
$$!+)
$3,( #/
!
$ #
w
.g
##- ,
)
$!$ #2
##/ 0 $
$$
!
!! *$ #2
## $4
$!
!
(
$ $$!
$6
!
! #
##2 ,!)
$ "
SPINDLE AMPLIFIER MODULE ................................................................................................. 144
w
w
3.4
#" α
$ α
""
#" $
3!"3$ !)
AA
! *$ $<!$ <
""
#" $
"-
://
#"# $
"/
#"" $
# "
ht
tp
#"- $
" "
#"/ $
"2
#" $
"2
#"2 $
"
#" $
-
#" $
# -
#" $
- -
#" $
/ -
#"# $
$ -
#"" $
" -
"
Table of Contents
B-65165E/02
#"- $
- -
#"/ $
/ -#
#" $
--
/
#"2 $
2 -/
ar
es
.co
m
#" $
-
#" $
# -2
#" $
# -2
#" $
# -
#"# $
## -
#"" $
#" -
#"- $
#- /
#"/ $
#/ /
#" $
# /
#" $(
# /
-s
p
#" $
" /#
#" $
" /"
#"# $
" /-
uc
#"" $
"# /#"- $
"" /#"/ $
"/ /-
an
#" $
" //
#"2 $
" /
ef
#" $
- /
#" $
- /
w
.g
#" $
-$ -# /2
#" $
-" /2
#"# $
-- /2
#"" $
-/ /
#"- $
- /
w
w
#"/ $
-2 /
#" $
- #"# α(
#"# $
://
#"# $
#- ht
tp
3.5
4
POWER-FAILURE BACKUP MODULE....................................................................................... 173
#- $(
#
#- $(
#
#-# $(
# #
#-" $(
" "
#-- $(
- "
HOW TO REPLACE THE FUSES AND PRINTED CIRCUIT BOARDS ...................175
4.1
CASE DISASSEMBLY ................................................................................................................. 178
" />8!)
2
-
Table of Contents
B-65165E/02
" -8!)
!)!!)
(
"# -8!)
!)!)
(
!
2
"" #8
!)!!)
(
!
REPLACING FUSES ................................................................................................................... 196
ar
es
.co
m
4.2
!
2-
/
"- #8
!)!)
(
!
2
" /
" "# "" %$
&$'
4.3
OTHER COMPONENTS.............................................................................................................. 203
"# 4
$ *!)
*$4,$ #
RECEIVING AND KEEPING AC SERVO MOTORS ................................................................... 210
1.2
DAILY INSPECTION OF AC SERVO MOTORS ......................................................................... 211
1.3
PERIODIC INSPECTION OF AC SERVO MOTORS .................................................................. 213
1.4
REPLACING THE PULSE CODER ............................................................................................. 216
1.5
SPECIFICATION NUMBERS OF REPLACEMENT PARTS ....................................................... 225
an
uc
1.1
ef
SPINDLE MOTOR MAINTENANCE .........................................................................227
2.1
PREVENTIVE MAINTENANCE ................................................................................................... 228
2.2
MAINTENANCE PARTS .............................................................................................................. 232
2.3
PERMISSIBLE RADIAL LOAD..................................................................................................... 236
ht
tp
://
w
w
2
AC SERVO MOTOR MAINTENANCE ......................................................................209
w
.g
1
-s
p
III. MOTOR MAINTENANCE
/
://
tp
ht
w
w
w
.g
ar
es
.co
m
-s
p
uc
an
ef
I. START-UP PROCEDURE
/
/
OVERVIEW
ar
es
.co
m
1
1. OVERVIEW
START-UP PROCEDURE
B-65165E/02
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
This part describes the units and components of the FANUC servo
amplifier α series. It also explains the following information necessary
to start up the control motor amplifier:
• Connecting the power
• Setting the printed-circuit board
• Initializing the parameter
• Confirmation of the operation
-3-
/
CONFIGURATIONS
B-65165E/02
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
2
START-UP PROCEDURE
ar
es
.co
m
2. CONFIGURATIONS
-4-
2.1
2. CONFIGURATIONS
START-UP PROCEDURE
B-65165E/02
CONFIGURATIONS
ar
es
.co
m
/
The FANUC servo amplifier α series consists of the units and
components listed below:
(1) Power supply module (PSM)
(basic)
(2) Servo amplifier module (SVM)
(basic)
(3) Spindle amplifier module (SPM)
(basic)
(4) AC reactor
(basic)
(5) Connectors (for connecting cables)
(basic)
(6) Fuses
(basic)
(7) Power transformer
(option)
(8) Fan adaptor
(option)
uc
-s
p
The diagram below shows an example of a basic configuration of the
FANUC servo amplifier α series system. The basic configuration
consists of two two-axis servo amplifier modules and one spindle
amplifier module.
Power supply
module
Spindle amplifier Servo amplifier
module
module (2-axis)
Servo amplifier
module (2-axis)
(380VAC)
(415VAC)
(460VAC)
DC link (300 VDC)
PSM
SPM
SVM
SVM
UL VL WL PE
UM VM WM PE
UL VL WL PE
UM VM WM
AC input for
control power
supply
200R,
200S, PE
1
L1 L2 L3 PE
U V W PE
Circuit breaker 2
200 VAC
220 VAC
230 VAC
1
Magnetic
contactor
AC
reactor
Spindle
motor
Servo
motor
Servo
motor
Servo
motor
Servo
motor
Circuit
breaker
1
3
Fan
3
Power transformer
Circuit breaker 3
: Standard
: Optional
: Units prepared by the machine tool builder
ht
tp
://
w
w
w
.g
ef
an
P
N
-5-
2. CONFIGURATIONS
START-UP PROCEDURE
B-65165E/02
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
ar
es
.co
m
/
NOTE
1 Refer to the Servo Amplifier α series Descriptions
(B-65162E) for combinations of the power supply
module, servo amplifier module, and spindle
amplifier module.
2 Always use the circuit breakers, magnetic contactor,
and AC reactor.
3 Install a surge suppressor between the power lines
and between each power line and a ground at the
input of the power magnetics cabinet to protect the
system from lightning surge.
-6-
2. CONFIGURATIONS
START-UP PROCEDURE
MAJOR COMPONENTS
2.2.1
Power Supply Modules
2.2.1.1
α series power supply modules
/
2.2
ar
es
.co
m
B-65165E/02
(1) Power supply modules (PSM) (200 VAC input, power regeneration
type), CE-marked products
Order specification
PSM-5.5
Unit
specification
Printed circuit
board
specification
A16B-2202-0420
(Revision 05D or
later)
Wiring board
specification
A06B-6077C106
(Revision B or
A06B-6077-H106#BM later)
A06B-6077-H106
(Revision B or later)
an
A06B-6087C130
(Revision B or
A20B-1006-0472
A06B-6087-H130#BM later)
A16B-2202-0421
(Revision 05D or
later)
A06B-6087-H137
A06B-6087A06B-6087-H137#BM C137
A16B-2202-0421
A16B-2202-0424
A06B-6087-H130
(Revision B or later)
w
w
PSM-30
A20B-1006-0680
://
A06B-6087-H145
PSM-45
tp
A06B-6087-H145#BM
ht
PSM-55
A06B-6087-H155
A06B-6087C145
A20B-1007-0650
A20B-1006-0680
A20B-1007-0650
A06B-6087A06B-6087-H155#BM C155
A20B-1007-0650
A20B-29020390
A16B-2202-0424
A16B-2202-0421
(Revision 05D or
later)
w
.g
PSM-26
A16B-2202-0421
(Revision 05D or
later)
A06B-6087C126
A20B-1006-0471
(Revision B or
A06B-6087-H126#BM later)
A06B-6087-H126
(Revision B or later)
ef
PSM-15
PSM-37
A16B-2202-0423
A06B-6087C115
A20B-1006-0470
(Revision B or
A06B-6087-H115#BM later)
A06B-6087-H115
(Revision B or later)
A16B-2202-0420
(Revision 05D or
later)
uc
A06B-6077-H111
(Revision B or later)
PSM-11
Connector
board
specification
A16B-2202-0423
A16B-2202-0661
A06B-6077C111
(Revision B or
A06B-6077-H111#BM later)
Driver board
specification
-s
p
Model
A16B-2202-0424
A16B-2202-0424
A16B-2202-0421
A20B-20020080
A16B-2202-0424
A16B-2202-0421
A16B-2202-0424
* The PSM-45 has been replaced by the PSM-55 (as of August 1999).
-7-
2. CONFIGURATIONS
START-UP PROCEDURE
B-65165E/02
(2) Power supply modules (PSMR) (200 VAC input, resistance
discharge type), CE-marked products
PSMR-5.5
A06B-6081-H103
(Revision C or later)
A06B-6081-H106
(Revision C or later)
Unit specification
A06B-6081-C103
A06B-6081-C106
Wiring board
specification
A16B-2202-0542
(Revision 06B or later)
A16B-2202-0541
(Revision 06B or later)
Printed circuit board
specification
/
PSMR-3
Order specification
A16B-2001-0890
ar
es
.co
m
Model
A16B-2001-0890
(3) Power supply modules (PSM) (200 VAC input, power
regeneration type), CE-marked products
Order
specification
PSM-5.5
PSM-11
A06B-6077-H106
(Revision A)
A06B-6077-H111
(Revision A)
Unit
specification
Wiring board
specification
A06B-6077-C106 A16B-2202-0460
(Revision A)
A16B-2202-0461
A06B-6077-C111
A16B-2202-0461
(Revision A)
A06B-6077-H115 A06B-6071-C112 A20B-1005-0591
an
A06B-6087-H115 A06B-6087-C115
A20B-1006-0160
(Revision A)
(Revision A)
A06B-6077-H126 A06B-6071-C122 A20B-1005-0590
A06B-6087-H126 A06B-6087-C126
(Revision B or
A20B-1006-0161
(Revision B or
earlier)
earlier)
ef
PSM-26
w
.g
A06B-6077-H130 A06B-6071-C126 A20B-1005-0592
A06B-6087-H130 A06B-6087-C130
(Revision B or
A20B-1006-0162
(Revision B or
earlier)
earlier)
w
w
PSM-30
PSMR-3
A20B-20010011
A16B-2202-0421 A20B-2902(Revision 04C or 0280
earlier)
A20B-2001A16B-2202-0080
0011
A16B-2202-0421 A20B-2902(Revision 04C or 0280
earlier)
A20B-2001A16B-2202-0080
0011
A16B-2202-0421 A20B-2902(Revision 04C or 0280
earlier)
A16B-2202-0080
A20B-20010130
A20B-20010130
A20B-20010130
Wiring board
Printed circuit board
specification
specification
A06B-6081-H103
A06B-6081-C103
A16B-2202-0542
A16B-2300-0100
(Revision B or earlier) (Revision B or earlier) (Revision 05A or earlier)
A06B-6081-H106
A06B-6081-C106
A16B-2202-0541
A16B-2300-0100
(Revision B or earlier) (Revision B or earlier) (Revision 05A or earlier)
Order specification
Unit specification
ht
tp
PSMR-5.5
Connector
board
specification
(4) Power supply modules (PSMR) (200 VAC input, resistance
discharge type), CE-marked products
://
Model
Driver board
specification
A16B-2202-0420
(Revision 04C or
earlier)
uc
PSM-15
Printed circuit
board
specification
-s
p
Model
-8-
2.2.1.2
2. CONFIGURATIONS
START-UP PROCEDURE
B-65165E/02
α (HV) series power supply modules
Model
ar
es
.co
m
/
(1) Power supply modules (PSM-HV) (400 VAC input, power
regeneration type)
Wiring board
specification
Order specification Unit specification
PSM-18HV
A06B-6091-H118
A06B-6091-C118 A20B-1006-0611
PSM-30HV
PSM-45HV
A06B-6091-H130
A06B-6091-H145
PSM-75HV
A06B-6091-H175
A06B-6091-C130 A20B-1006-0610
A06B-6091-C145 A20B-1006-0612
A20B-1006-0681
A06B-6091-C175
A20B-1007-0651
Driver board
specification
A20B-2002-0080
Printed circuit
board
specification
A16B-2202-0422
(2) Capacitor modules (PSMC-HV) (for the PSM-HV series)
Order specification Unit specification
Capacitor specification
-s
p
Model
A06B-6083-C218 A42L-0001-0340
(× 2)
PSMC-30HV A06B-6083-H230
PSMC-45HV A06B-6083-H245
A06B-6083-C230 A42L-0001-0314
A06B-6083-C245 A42L-0001-0322
(× 2)
(× 2)
uc
PSMC-18HV A06B-6083-H218
Wiring board
specification
Order specification Unit specification
PSMV-11HV A06B-6098-H111
A06B-6098-C111 A20B-1007-0200
ef
Model
an
(3) Power supply module (PSMV-HV) (400 VAC input, 300 VDC
output, power regeneration type)
Driver board
specification
Printed circuit
board
specification
A20B-2002-0530
A16B-2203-0220
Order specification
Unit specification
AC reactor
A06B-6098-C001
A81L-0001-0144
ht
tp
://
w
w
A06B-6098-H001
w
.g
(4) AC reactor unit (PSMV-HV)
-9-
Fuse
A60L-0001-0362#100U
2. CONFIGURATIONS
START-UP PROCEDURE
Servo Amplifier Modules
2.2.2.1
200-V input series
ar
es
.co
m
/
2.2.2
B-65165E/02
(1) Single-axis servo amplifier modules (interface: Type A/B)
Order
specification
Model
A16B-2202-0742
SVM1-4
A06B-6079-H122
A16B-2202-0743
SVM1-12
A06B-6079-H101
A16B-2202-0740
SVM1-20
A06B-6079-H102
A16B-2202-0741
SVM1-40S
A06B-6079-H103
A16B-2203-0450 A20B-2001-0930
(A16B-2202-0760)
SVM1-40L
A06B-6079-H104
SVM1-80
A06B-6079-H105
SVM1-130
A06B-6079-H106
SVM1-240
A06B-6079-H107
A16B-2203-0451
(A16B-2202-0761)
A16B-2203-0452
(A16B-2202-0762)
A16B-2203-0454
A20B-2001-0932
(A16B-2202-0790)
A20B-1006-0485 A16B-2202-0990
SVM1-360
A06B-6079-H108
A20B-1006-0485
Enclosed in parentheses are the
drawing numbers of the old
specifications.
uc
-s
p
A06B-6079-H121
Remarks
an
SVM1-2
Printed circuit
board
specification
Wiring board
specification
A16B-2202-0991
Order
specification
Wiring board
specification
w
.g
Model
ef
(2) Two-axis servo amplifier modules (interface: Type A/B)
A06B-6079-H291
A16B-2202-0753
SVM2-12/12
A06B-6079-H201
A16B-2202-0750
SVM2-12/20
A06B-6079-H202
A16B-2202-0751
w
w
SVM2-3/3
Printed circuit
board
specification
A06B-6079-H203
A16B-2202-0752
SVM2-12/40
A06B-6079-H204
A16B-2203-0590 A20B-2001-0931
(A16B-2202-0770)
SVM2-20/40
A06B-6079-H205
SVM2-40/40
A06B-6079-H206
tp
://
SVM2-20/20
ht
SVM2-40/80
A06B-6079-H207
SVM2-80/80
A06B-6079-H208
SVM2-40L/40L
A06B-6079-H209
A16B-2203-0591
(A16B-2202-0771)
A16B-2203-0592
(A16B-2202-0772)
A16B-2203-0593
(A16B-2202-0773)
A16B-2203-0594
A20B-2001-0933
(A16B-2202-0774)
A16B-2203-0595
(A16B-2202-0775)
- 10 -
Remarks
Enclosed in parentheses are the
drawing numbers of the old
specifications.
START-UP PROCEDURE
B-65165E/02
2. CONFIGURATIONS
(3) Three-axis servo amplifier modules (interface: Type A)
Printed circuit
board
specification
SVM3-12/12/12
A06B-6079-H301
A16B-2202-0780
SVM3-12/12/20
A06B-6079-H302
A16B-2202-0781
SVM3-12/20/20
A06B-6079-H303
A16B-2202-0782
SVM3-20/20/20
A06B-6079-H304
A16B-2202-0783
SVM3-12/12/40
A06B-6079-H305
A16B-2202-0784
SVM3-12/20/40
A06B-6079-H306
A16B-2202-0785
SVM3-20/20/40
A06B-6079-H307
A16B-2202-0786
Remarks
/
Wiring board
specification
A20B-2001-0940
ar
es
.co
m
Order
specification
Model
(4) Three-axis servo amplifier modules (interface: Type B)
Printed circuit
board
specification
Wiring board
specification
A06B-6080-H301
A16B-2202-0780
SVM3-12/12/20
A06B-6080-H302
A16B-2202-0781
SVM3-12/20/20
A06B-6080-H303
A16B-2202-0782
SVM3-20/20/20
A06B-6080-H304
A16B-2202-0783
SVM3-12/12/40
A06B-6080-H305
A16B-2202-0784
SVM3-12/20/40
A06B-6080-H306
A16B-2202-0785
SVM3-20/20/40
A06B-6080-H307
A16B-2202-0786
uc
SVM3-12/12/12
Remarks
-s
p
Order
specification
Model
an
A20B-2001-0950
Order
specification
Wiring board
specification
w
.g
Model
ef
(5) Single-axis servo amplifier module (interface: FSSB)
A16B-2202-0742
SVM1-4
A06B-6096-H122
A16B-2202-0743
SVM1-12
A06B-6096-H101
A16B-2202-0740
SVM1-20
A06B-6096-H102
A16B-2202-0741
SVM1-40S
A06B-6096-H103
A16B-2203-0450
(A16B-2202-0760)
w
w
A06B-6096-H121
A06B-6096-H104
tp
A16B-2203-0451
A20B-2100-0540 When using HRV3, use the following
(A16B-2202-0761)
(A20B-2100-0250) boards together:
Wiring board: A16B-2203-045X
A16B-2203-0452
Printed circuit board:
(A16B-2202-0762)
A20B-2100-054X
A16B-2203-0453
SVM1-40L
SVM1-80
A06B-6096-H105
SVM1-130S
A06B-6096-H116
SVM1-130
A06B-6096-H106
A16B-2203-0454 A20B-2100-0542
(A16B-2202-0790) (A20B-2100-0252)
SVM1-240
A06B-6096-H107
A20B-1006-0485
A16B-2203-0300
SVM1-360
A06B-6096-H108
A20B-1006-0485
A16B-2203-0301
ht
Remarks
When using HRV3, use the following
boards together:
A20B-2100-0540
Wiring board: A16B-2202-074X
(A20B-2100-0250)
Printed circuit board:
A20B-2100-054X
SVM1-2
://
Printed circuit
board
specification
- 11 -
2. CONFIGURATIONS
START-UP PROCEDURE
B-65165E/02
(6) Two-axis servo amplifier modules (interface: FSSB)
Printed circuit
board
specification
A06B-6096-H291
A16B-2202-0753
SVM2-12/12
A06B-6096-H201
A16B-2202-0750
SVM2-12/20
A06B-6096-H202
A16B-2202-0751
SVM2-20/20
A06B-6096-H203
A16B-2202-0752
SVM2-12/40
A06B-6096-H204
SVM2-20/40
A06B-6096-H205
SVM2-40/40
A06B-6096-H206
SVM2-40/80
A06B-6096-H207
SVM2-80/80
A06B-6096-H208
SVM2-40L/40L
A06B-6096-H209
When using HRV3, use the following
boards together:
A20B-2100-0541
Wiring board: A16B-2202-075X
(A20B-2100-0251)
Printed circuit board:
A20B-2100-054X
A20B-2100-0541
(A20B-2100-0251)
When using HRV3, use the following
boards together:
Wiring board: A16B-2203-059X
Printed circuit board:
A20B-2100-054X
A20B-2100-0543
(A20B-2100-0253)
uc
A16B-2203-0590
(A16B-2202-0770)
A16B-2203-0591
(A16B-2202-0771)
A16B-2203-0592
(A16B-2202-0772)
A16B-2203-0593
(A16B-2202-0773)
A16B-2203-0594
(A16B-2202-0774)
A16B-2203-0595
(A16B-2202-0775)
ar
es
.co
m
SVM2-3/3
Remarks
/
Wiring board
specification
-s
p
Order
specification
Model
(7) Three-axis servo amplifier modules (interface: FSSB)
Printed circuit
board
specification
an
Order
specification
Model
Wiring board
specification
A06B-6096-H301
SVM3-12/12/20
A06B-6096-H302
A16B-2202-0780
SVM3-12/20/20
A06B-6096-H303
SVM3-20/20/20
A06B-6096-H304
A16B-2202-0783
SVM3-12/12/40
A06B-6096-H305
A16B-2202-0784
SVM3-12/20/40
A06B-6096-H306
A16B-2202-0785
SVM3-20/20/40
A06B-6096-H307
A16B-2202-0786
ef
SVM3-12/12/12
A16B-2202-0781
A20B-2100-0260
ht
tp
://
w
w
w
.g
A16B-2202-0782
- 12 -
Remarks
START-UP PROCEDURE
B-65165E/02
2.2.2.2
2. CONFIGURATIONS
400-V input series
Printed circuit
board
specification
Wiring board
specification
SVM1-20HV
A06B-6085-H102
A16B-2202-0800
SVM1-40HV
A06B-6085-H103
A16B-2202-0801
SVM1-60HV
A06B-6085-H104
A16B-2202-0802
A20B-2001-0932
Remarks
ar
es
.co
m
Order
specification
Model
(2) Two-axis servo amplifier modules (interface: Type A/B)
Printed circuit
board
specification
Wiring board
specification
A06B-6085-H201
A16B-2203-0210
SVM2-20/40HV
A06B-6085-H202
A16B-2203-0211
SVM2-20/60HV
A06B-6085-H203
A16B-2203-0212
SVM2-40/40HV
A06B-6085-H204
A16B-2203-0213
SVM2-40/60HV
A06B-6085-H205
A16B-2203-0214
SVM2-60/60HV
A06B-6085-H206
A16B-2203-0215
A20B-2001-0933
an
uc
SVM2-20/20HV
Remarks
-s
p
Order
specification
Model
(3) Single-axis servo amplifier modules (interface: FSSB)
A06B-6097-H102
SVM1-40HV
A06B-6097-H103
SVM1-60HV
A06B-6097-H104
A16B-2202-0802
A16B-2202-0803
A06B-6097-H107
A20B-1007-0592
://
w
w
A06B-6097-H105
SVM1-320HV
Order
specification
Wiring board
specification
A06B-6097-H201
A16B-2203-0210
SVM2-20/40HV
A06B-6097-H202
A16B-2203-0211
SVM2-20/60HV
A06B-6097-H203
A16B-2203-0212
tp
A20B-2100-0542 Enclosed in parentheses is the
(A20B-2100-0252) drawing number of the old
specification.
A16B-2203-0301
(4) Two-axis servo amplifier modules (interface: FSSB)
SVM2-20/20HV
ht
Remarks
A16B-2202-0801
SVM1-80HV
Model
Printed circuit
board
specification
A16B-2202-0800
w
.g
SVM1-20HV
Wiring board
specification
ef
Order
specification
Model
SVM2-40/40HV
A06B-6097-H204
A16B-2203-0213
SVM2-40/60HV
A06B-6097-H205
A16B-2203-0214
SVM2-60/60HV
A06B-6097-H206
A16B-2203-0215
Printed circuit
board
specification
Remarks
A20B-2100-0543 Enclosed in parentheses is the
(A20B-2100-0253) drawing number of the old
specification.
- 13 -
/
(1) Single-axis servo amplifier modules (interface: Type A/B)
2. CONFIGURATIONS
START-UP PROCEDURE
Spindle Amplifier Modules
2.2.3.1
α series spindle amplifier modules
ar
es
.co
m
/
2.2.3
B-65165E/02
The order specification varies according to the detector (function)
used.
(1) α series spindle amplifier modules (SPM) type 1 (standard
specification)
New specification (supporting spindle HRV control), CE-marked
products
Order specification
Wiring board
specification
Unit specification
Printed circuit
board
specification
A16B-2203-0500
ROM (series)
-s
p
Model
A16B-2203-0501
ht
tp
://
w
w
w
.g
ef
an
uc
SPM-2.2 A06B-6102-H202#H520 A06B-6102-H202 A16B-2202-0680
SPM-5.5 A06B-6102-H206#H520 A06B-6102-H206 A16B-2202-0681
SPM-11 A06B-6102-H211#H520 A06B-6102-H211 A16B-2202-0682
A20B-1006-0486
SPM-15 A06B-6102-H215#H520 A06B-6102-H215
A20B-2902-0390
A20B-1006-0487
SPM-22 A06B-6102-H222#H520 A06B-6102-H222
A20B-2902-0390
A20B-1006-0488
SPM-26 A06B-6102-H226#H520 A06B-6102-H226
A20B-2902-0390
A20B-1006-0489
SPM-30 A06B-6102-H230#H520 A06B-6102-H230
A20B-2902-0390
A20B-1007-0591
SPM-45 A06B-6102-H245#H520 A06B-6102-H245
A20B-2002-0080
A20B-1007-0590
SPM-55 A06B-6102-H255#H520 A06B-6102-H255
A20B-2002-0081
- 14 -
A06B-6102-H520
(9D20)
A16B-2203-0502
START-UP PROCEDURE
B-65165E/02
2. CONFIGURATIONS
CE-marked products
Unit specification
Wiring board
specification(*1)
SPM-2.2 A06B-6078-H202#H500 A06B-6078-H202 A16B-2202-0680
ROM (series)
A06B-6072-H500
(9D00, 9D0A)
A16B-2203-0332
(A16B-2202-0432)
an
Enclosed in parentheses are the drawing numbers of the old
specifications.
ht
tp
://
w
w
w
.g
ef
*1
uc
-s
p
SPM-5.5 A06B-6078-H206#H500 A06B-6078-H206 A16B-2202-0681
SPM-11 A06B-6078-H211#H500 A06B-6078-H211 A16B-2202-0682
A20B-1006-0486
SPM-15 A06B-6088-H215#H500 A06B-6088-H215 (A20B-1006-0480)
A20B-2902-0390
A20B-1006-0487
SPM-22 A06B-6088-H222#H500 A06B-6088-H222 (A20B-1006-0481)
A20B-2902-0390
A20B-1006-0488
SPM-26 A06B-6088-H226#H500 A06B-6088-H226 (A20B-1006-0482)
A20B-2902-0390
A20B-1006-0489
SPM-30 A06B-6088-H230#H500 A06B-6088-H230 (A20B-1006-0483)
A20B-2902-0390
A20B-1007-0591
SPM-45 A06B-6088-H245#H500 A06B-6088-H245 (A20B-1006-0690)
A20B-2002-0080
Printed circuit
board
specification(*1)
A16B-2203-0330
(A16B-2202-0430)
A16B-2203-0331
(A16B-2202-0431)
/
Order specification
ar
es
.co
m
Model
- 15 -
2. CONFIGURATIONS
START-UP PROCEDURE
B-65165E/02
Non-CE-marked products
Wiring board
specification
Unit specification
SPM-2.2 A06B-6078-H202#H500 A06B-6078-H202 A16B-2202-0470
SPM-5.5 A06B-6078-H206#H500 A06B-6078-H206 A16B-2202-0471
SPM-11 A06B-6078-H211#H500 A06B-6078-H211 A16B-2202-0472
A20B-1006-0170
SPM-15 A06B-6088-H215#H500 A06B-6088-H215
A20B-2902-0280
A20B-1006-0171
SPM-22 A06B-6088-H222#H500 A06B-6088-H222
A20B-2902-0280
A20B-1006-0172
SPM-26 A06B-6088-H226#H500 A06B-6088-H226
A20B-2902-0280
Printed circuit
board
specification(*1)
A16B-2203-0330
(A16B-2202-0430)
A16B-2203-0331
(A16B-2202-0431)
ROM (series)
/
Order specification
ar
es
.co
m
Model
A06B-6072-H500
(9D00, 9D0A)
A16B-2203-0332
(A16B-2202-0432)
Non-CE-marked products (old specifications)
Order specification
Wiring board
specification
Unit specification
A20B-1005-0572
A20B-2001-0010
A20B-1005-0571
A06B-6078-H222#H500 A06B-6078-H222
A20B-2001-0010
A20B-1005-0570
A06B-6078-H226#H500 A06B-6078-H226
A20B-2001-0010
A20B-1005-0575
A06B-6078-H230#H500 A06B-6078-H230
A20B-2001-0010
A06B-6078-H215#H500 A06B-6078-H215
uc
SPM-15
SPM-22
an
SPM-26
ROM (series)
A16B-2202-0070
A20B-2001-0150
A20B-2901-0851
A06B-6072-H500
(9D00, 9D0A)
ef
SPM-30
Printed circuit
board
specification
-s
p
Model
w
.g
Applicable detectors
<1> M sensor (pulse generator), position coder, magnetic sensor
<2> MZ sensor (sensor built into a motor)
Enclosed in parentheses are the drawing numbers of the old
specifications.
ht
tp
://
w
w
*1
- 16 -
START-UP PROCEDURE
B-65165E/02
2. CONFIGURATIONS
(2) α series spindle amplifier modules (SPM), type 2 (Cs contour
control/BZ sensor (separate built-in sensor) specification)
Order specification
Unit specification
Wiring board
specification(*1)
SPM-2.2 A06B-6078-H302#H500 A06B-6078-H302 A16B-2202-0680
-s
p
SPM-5.5 A06B-6078-H306#H500 A06B-6078-H306 A16B-2202-0681
SPM-11 A06B-6078-H311#H500 A06B-6078-H311 A16B-2202-0682
A20B-1006-0486
SPM-15 A06B-6088-H315#H500 A06B-6088-H315 (A20B-1006-0480)
A20B-2902-0390
A20B-1006-0487
SPM-22 A06B-6088-H322#H500 A06B-6088-H322 (A20B-1006-0481)
A20B-2902-0390
A20B-1006-0488
SPM-26 A06B-6088-H326#H500 A06B-6088-H326 (A20B-1006-0482)
A20B-2902-0390
A20B-1006-0489
SPM-30 A06B-6088-H330#H500 A06B-6088-H330 (A20B-1006-0483)
A20B-2902-0390
A20B-1007-0591
SPM-45 A06B-6088-H345#H500 A06B-6088-H345 (A20B-1006-0690)
A20B-2002-0080
Printed circuit
board
specification
A16B-2202-0433
A20B-2901-0851
A16B-2202-0434
A20B-2901-0851
ar
es
.co
m
Model
/
CE-marked products
ROM (series)
A06B-6072-H500
(9D00, 9D0A)
ef
an
uc
A16B-2202-0435
A20B-2901-0851
Non-CE-marked products
Order specification
Unit specification
w
.g
Model
Wiring board
specification
SPM-2.2 A06B-6078-H302#H500 A06B-6078-H302 A16B-2202-0470
ROM (series)
A06B-6072-H500
(9D00, 9D0A)
A16B-2202-0435
A20B-2901-0851
*1
Enclosed in parentheses are the drawing numbers of the old
specifications.
ht
tp
://
w
w
SPM-5.5 A06B-6078-H306#H500 A06B-6078-H306 A16B-2202-0471
SPM-11 A06B-6078-H311#H500 A06B-6078-H311 A16B-2202-0472
A20B-1006-0170
SPM-15 A06B-6088-H315#H500 A06B-6088-H315
A20B-2902-0280
A20B-1006-0171
SPM-22 A06B-6088-H322#H500 A06B-6088-H322
A20B-2902-0280
A20B-1006-0172
SPM-26 A06B-6088-H326#H500 A06B-6088-H326
A20B-2902-0280
Printed circuit
board
specification
A16B-2202-0433
A20B-2901-0851
A16B-2202-0434
A20B-2901-0851
- 17 -
2. CONFIGURATIONS
START-UP PROCEDURE
B-65165E/02
Non-CE-marked products (old specification)
Wiring board
specification
Unit specification
A20B-1005-0572
A20B-2001-0010
A20B-1005-0571
A06B-6078-H322#H500 A06B-6078-H322
A20B-2001-0010
A20B-1005-0570
A06B-6078-H326#H500 A06B-6078-H326
A20B-2001-0010
A20B-1005-0575
A06B-6078-H230#H500 A06B-6078-H330
A20B-2001-0010
SPM-15
A06B-6078-H315#H500 A06B-6078-H315
SPM-22
SPM-26
SPM-30
Printed circuit
board
specification
ROM (series)
/
Order specification
ar
es
.co
m
Model
A16B-2202-0160
A20B-2001-0140
A20B-2901-0851
A06B-6072-H500
(9D00, 9D0A)
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
Applicable detectors
<1> M sensor (pulse generator) + BZ sensor (separate built-in
sensor) (use of position coder signals only)
<2> High-resolution magnetic pulse coder (for motor only)
<3> High-resolution magnetic pulse coder (for motor and
spindle)
<4> High-resolution position coder + high-resolution magnetic
pulse coder (for motor only)
- 18 -
START-UP PROCEDURE
B-65165E/02
2. CONFIGURATIONS
(3) α series spindle amplifier modules (SPM), type 3 (spindle
switching control/differential speed control specification)
SPM-11
A06B-6088-H411#H500 A06B-6088-H411
SPM-15
A06B-6088-H415#H500 A06B-6088-H415
SPM-22
A06B-6088-H422#H500 A06B-6088-H422
A06B-6088-H426#H500 A06B-6088-H426
SPM-30
A06B-6088-H430#H500 A06B-6088-H430
SPM-45
A06B-6088-H445#H500 A06B-6088-H445
A20B-1006-0484
A20B-2902-0390
A20B-1006-0486
(A20B-1006-0480)
A20B-2902-0390
A20B-1006-0487
(A20B-1006-0481)
A20B-2902-0390
A20B-1006-0488
(A20B-1006-0482)
A20B-2902-0390
A20B-1006-0489
(A20B-1006-0483)
A20B-2902-0390
A20B-1007-0591
(A20B-1006-0690)
A20B-2002-0080
an
SPM-26
Wiring board
specification(*1)
Printed circuit
board
specification
ROM (series)
A16B-2202-0440
A20B-2001-0700
A20B-2901-0851
A06B-6072-H500
(9D00, 9D0A)
ar
es
.co
m
Unit specification
-s
p
Order specification
uc
Model
/
CE-marked products
Order specification
Unit specification
w
.g
Model
ef
Non-CE-marked products
A06B-6078-H411#H500 A06B-6078-H411
SPM-15
A06B-6078-H415#H500 A06B-6078-H415
SPM-22
A06B-6078-H422#H500 A06B-6078-H422
SPM-26
A06B-6078-H426#H500 A06B-6078-H426
A06B-6078-H430#H500 A06B-6078-H430
ht
tp
://
SPM-30
w
w
SPM-11
Wiring board
specification
A20B-1005-0574
A20B-2001-0010
A20B-1005-0572
A20B-2001-0010
A20B-1005-0571
A20B-2001-0010
A20B-1005-0570
A20B-2001-0010
A20B-1005-0575
A20B-2001-0010
Printed circuit
board
specification
ROM (series)
A16B-2202-0160
A20B-2001-0140
A20B-2901-0851
A06B-6072-H500
(9D00, 9D0A)
Applicable functions
<1> Spindle switching control (switching of speed only or
switching of speed and position)
<2> Spindle switching control (switching of MZ sensor (built-in
sensor))
<3> Differential speed control (position coder signal input
circuit)
*1
Enclosed in parentheses are the drawing numbers of the old
specifications.
- 19 -
2. CONFIGURATIONS
START-UP PROCEDURE
B-65165E/02
(4) α series spindle amplifier modules (SPM), type 4 (α sensor Cs
contour control)
Model
Order specification
Wiring board
specification
Unit specification
SPM-2.2 A06B-6102-H102#H520 A06B-6102-H102 A16B-2202-0680
Printed circuit
board
specification
A16B-2203-0503
A20B-2902-0620
A16B-2203-0504
A20B-2902-0620
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
SPM-5.5 A06B-6102-H106#H520 A06B-6102-H106 A16B-2202-0681
SPM-11 A06B-6102-H111#H520 A06B-6102-H111 A16B-2202-0682
A20B-1006-0486
SPM-15 A06B-6102-H115#H520 A06B-6102-H115
A20B-2902-0390
A20B-1006-0487
SPM-22 A06B-6102-H122#H520 A06B-6102-H122
A20B-2902-0390
A20B-1006-0488
SPM-26 A06B-6102-H126#H520 A06B-6102-H126
A20B-2902-0390
A20B-1006-0489
SPM-30 A06B-6102-H130#H520 A06B-6102-H130
A20B-2902-0390
A20B-1007-0591
SPM-45 A06B-6102-H145#H520 A06B-6102-H145
A20B-2002-0080
A20B-1007-0590
SPM-55 A06B-6102-H155#H520 A06B-6102-H155
A20B-2002-0081
ar
es
.co
m
/
New specification (supporting spindle HRV control), CE-marked
products
- 20 -
A16B-2203-0505
A20B-2902-0620
ROM (series)
A06B-6102-H520
(9D20)
START-UP PROCEDURE
B-65165E/02
2. CONFIGURATIONS
CE-marked products
Unit specification
Wiring board
specification(*1)
SPM-2.2 A06B-6078-H102#H500 A06B-6078-H102 A16B-2202-0680
SPM-5.5 A06B-6078-H106#H500 A06B-6078-H106 A16B-2202-0681
SPM-11
A06B-6078-H111#H500 A06B-6078-H111 A16B-2202-0682
A20B-1006-0486
A06B-6088-H115#H500 A06B-6088-H115 (A20B-1006-0480)
A20B-2902-0390
A20B-1006-0487
A06B-6088-H122#H500 A06B-6088-H122 (A20B-1006-0481)
A20B-2902-0390
A20B-1006-0488
A06B-6088-H126#H500 A06B-6088-H126 (A20B-1006-0482)
A20B-2902-0390
A20B-1006-0489
A06B-6088-H130#H500 A06B-6088-H130 (A20B-1006-0483)
A20B-2902-0390
A20B-1007-0591
A06B-6088-H145#H500 A06B-6088-H145 (A20B-1006-0690)
A20B-2002-0080
-s
p
SPM-15
Printed circuit
board
specification(*1)
A16B-2202-0433
Overall revision 16E
or later
A20B-2902-0620
(A20B-2902-0610)
A16B-2202-0434
Overall revision 16E
or later
A20B-2902-0620
(A20B-2902-0610)
SPM-22
uc
SPM-26
A06B-6072-H500
(9D00, 9D0A)
A16B-2202-0435
Overall revision 13C
or later
A20B-2902-0620
(A20B-2902-0610)
an
SPM-30
ROM (series)
/
Order specification
ar
es
.co
m
Model
ef
SPM-45
*1
Enclosed in parentheses are the drawing numbers of the old
specifications.
ht
tp
://
w
w
w
.g
Applicable detectors
<1> MZ sensor (sensor built into a motor)
<2> MZ sensor (sensor built into a motor) + BZ sensor (separate
built-in sensor)
- 21 -
2. CONFIGURATIONS
2.2.4
START-UP PROCEDURE
B-65165E/02
Power-Failure Backup Modules
Wiring board
specification
Printed circuit board
specification
Remarks
ar
es
.co
m
Order specification
/
(1) Power-failure backup modules
A06B-6077-H001
A16B-2203-0360
A20B-2002-0790
Without the control power supply backup function
A06B-6077-H002
A16B-2203-0510
A20B-2003-0020
With the control power supply backup function
(2) Sub-module C (auxiliary capacitor unit)
Order specification
A06B-6077-C010
Capacitor specification
A42L-0001-0375
(× 2)
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
A06B-6077-H010
Unit specification
- 22 -
ar
es
.co
m
START-UP PROCEDURE
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
3
3. START-UP PROCEDURE
/
START-UP PROCEDURE
B-65165E/02
- 23 -
3. START-UP PROCEDURE
3.1
START-UP PROCEDURE
B-65165E/02
START-UP PROCEDURE (OVERVIEW)
ar
es
.co
m
/
Make sure that the specifications of the CNC, servo motors, servo
amplifiers, and other units you received are exactly what you ordered,
and these units are connected correctly. Then, turn on the power.
(1) Before turning on the circuit breaker, check the power supply
voltage connected.
→ See Section 3.2.
(2) Some types of PSM, SVM, and SPM require settings before the
system can be used. So check whether you must make settings.
→ See Section 3.3.
-s
p
(3) Turn on the power, and set initial parameters on the CNC.
an
uc
For the initialization of servo parameters, refer to the following
manual:
FANUC AC SERVO MOTOR α series Parameter Manual
(B-65150E)
w
.g
ef
For the initialization of spindle parameters, refer to the following
manual:
FANUC AD SPINDLE MOTOR α series Parameter Manual
(B-65160E)
ht
tp
://
w
w
(4) For start-up adjustment and troubleshooting, see Chapter 4.
• Method of using optional wiring boards for adjustment of the
PSM, SVM, and SPM
• Spindle sensor adjustment values
- 24 -
3. START-UP PROCEDURE
CONNECTING THE POWER
3.2.1
Checking The Voltage And Capacity Of The Power
ar
es
.co
m
3.2
/
START-UP PROCEDURE
B-65165E/02
Before connecting the power, you should measure the AC power
voltage.
Table 3.2.1(1) Action for the AC power (200-V input type)
AC power
Nominal
voltage
voltage
170 to 220 V 200 V
210 to 253 V 230 V
Action
These power lines can be connected directly to
the system.
Note) If the voltage is below the rated value, the
rated output may not be obtained.
380 to 550 V This power line must be connected through an
insulation transformer to step down the voltage
to 200 V.
-s
p
254 V or
more
uc
Table 3.2.1(2) Action for the AC power (400-V input type)
AC power
Nominal
voltage
voltage
340 to 440 V 400 V
391 to 506 V 460 V
Action
ef
an
These power lines can be connected directly to
the system.
Note) If the voltage is below the rated value, the
rated output may not be obtained.
480 to 550 V This power line must be connected through an
insulation transformer to step down the voltage
to 400 V.
w
.g
507 V or
more
://
w
w
Table 3.2.1 (3) to (5) list the input power specification for the power
supply module. Use a power source with sufficient capacity so that the
system will not malfunction due to a voltage drop even at a time of peak
load. Make sure that the AC power voltage value including voltage
fluctuation at a time of peak load is within the range specified in the
above table.
tp
Model
Table 3.2.1 (3) AC power voltage specifications
PSMR
-3
PSMR
-5.5
PSM
-5.5
5
12
9
ht
Nominal voltage rating
Power source frequency
Power source capacity (for
the main circuit) [kVA]
Power source capacity (for
the control circuit) [kVA]
PSM
PSM
PSM
PSM
-11
-15
-26
-30
200/220/230 VAC -15%, +10%
50/60 Hz ±1 Hz
17
0.5
22
37
44
0.7
- 25 -
PSM
-37
PSM
-45
PSM
-55
53
64
79
3. START-UP PROCEDURE
START-UP PROCEDURE
B-65165E/02
Table 3.2.1 (4) AC power voltage specifications (for the main circuit)
PSM-18HV
PSM-30HV
PSM-45HV
400/460 VAC -15%, +10%
50/60 Hz ±1 Hz
31
26
44
64
PSM-75HV
107
/
PSMV-11HV
ar
es
.co
m
Model
Nominal voltage rating
Power source frequency
Power source capacity
[kVA]
Table 3.2.1 (5) AC power voltage specifications (for the control circuit)
3.2.2
PSMV-11HV
PSM-18HV
PSM-30HV
PSM-45HV
200/220/230 VAC -15%, +10%
50/60 Hz ±1 Hz
0.7
PSM-75HV
-s
p
Model
Nominal voltage rating
Power source frequency
Power source capacity
[kVA]
Connecting A Protective Ground
ef
Selecting The Ground Fault Interrupter That Matches The
Leakage Current
w
.g
3.2.3
an
uc
Refer to the items in Chapter 5, "Installation," in "FANUC SERVO
AMPLIFIER α series Descriptions" B-65162E, and check that the
protective ground line is connected correctly.
ht
tp
://
w
w
Refer to the items in Chapter 5, "Installation," in "FANUC SERVO
AMPLIFIER α series Descriptions" B-65162E, and check that a
correct ground fault interrupter is selected.
- 26 -
START-UP PROCEDURE
B-65165E/02
3.3
3. START-UP PROCEDURE
SETTING THE PRINTED-CIRCUIT BOARD
3.3.1
Power Supply Module
Checking the DIP switch setting
(1) CE-marked products
Model
PSM-5.5 to 11
DIP switch
S1
S2
S1
S2
S1
S2
PSM-15 to 55
Description
Do not change the setting of the
DIP switches because they were
already set at the factory.
This setting has been made in shipments after January, 2000. In
earlier products, this switch was factory-set to SHORT.
uc
*1
Position
SHORT
OPEN(*1)
SHORT
OPEN
SHORT
OPEN
-s
p
PSM-18HV to
75HV
ar
es
.co
m
/
Before supplying power, set the printed-circuit board as listed below.
(2) Non-CE-marked products
DIP switch
S1
S2
S1
S2
an
Model
PSM-5.5 to 11
ht
tp
://
w
w
w
.g
ef
PSM-15 to 30
- 27 -
Position
SHORT
OPEN
SHORT
OPEN
Description
Do not change the setting of the
DIP switches because they were
already set at the factory.
3. START-UP PROCEDURE
3.3.2
START-UP PROCEDURE
B-65165E/02
Servo Amplifier Module
S1
S2
an
uc
-s
p
FANUC
ar
es
.co
m
/
(1) Checking the jumper plug setting (for SVM1 and SVM2)
Set the servo amplifier module to either interface type A or B with
the jumper plugs.
Move the jumper plugs as required. If
you cannot pull out a jumper plug with
your thumb and finger, use long-nose
pliers or the like.
w
.g
ef
FUSE
ht
tp
://
w
w
Jumper plug
S1
S2
SHORT OPEN
OPEN
SHORT
Description
With this setting, the servo amplifier module can operate
with the CNC (such as FS0, FS15, FS16, FS18, or PMD) designed for operation with interface type A. In this
case the JV*B connector is used.
With this setting, the servo amplifier module can operate
with the CNC (such as FS20 or FS21-G) designed for
operation with interface type B. In this case the JS*B
and JF* connectors are used.
NOTE
There is no jumper plug or DIP switch on the threeaxis servo amplifier module. The specification of the
servo amplifier module determines the type (A or B)
of the interface with which it can operate.
(2) Mounting the batteries for the ABS pulse coder
See Sec. I.5.1.
- 28 -
START-UP PROCEDURE
B-65165E/02
3. START-UP PROCEDURE
Spindle Amplifier Module
3.3.3.1
α series spindle amplifier module (SPM)
ar
es
.co
m
/
3.3.3
This type of modules do not have a DIP switch except the modules of
which specification drawing numbers are A06B-6072-H***#00xx (D
series spindle amplifier modules) and A06B-6078-H***#H5xx (nonCE-marked α series spindle amplifier modules).
Location of the DIP switch
DIP switch
-s
p
S7
SW
ef
an
uc
S1
F2
5A
w
.g
DIP
switch
S1
S3
S4
S5
ht
tp
://
w
w
S2
S6
S7
Switch setting
(factory-set to the
Description
underlined position)
ON
If two SPMs are connected to one serial interface
cable, S1 is set to ON in one SPM, and to OFF in
OFF
the other.
ON
If an analog filter is used at the load meter output,
S2 is set to ON. If not, it is set to OFF.
OFF
ON
If an analog filter is used at the speedometer
output, S3 is set to ON. If not, it is set to OFF.
OFF
S4:ON, S5:OFF
Reference switch of
Reference switch
NPN type (pull up)
(external reference signal
receive function) setting
S4:OFF, S5:OFF
Reference switch of
for the main spindle
PNP type (pull down)
S4:OFF, S5:OFF
The external reference
signal receive function.
Reference switch
S6:ON, S7:OFF
Reference switch of
(external reference signal
NPN type (pull up)
receive function) setting
S6:OFF, S7:OFF
Reference switch of
for the sub-spindle
PNP type (pull down)
S6:OFF, S7:OFF
The external reference
signal receive function
is not used.
- 29 -
3. START-UP PROCEDURE
3.3.3.2
START-UP PROCEDURE
B-65165E/02
α (HV) series spindle amplifier module (SPM-HV)
αC series spindle amplifier module (SPMC)
ar
es
.co
m
3.3.3.3
/
This module does not have a DIP switch.
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
This module does not have a DIP switch.
- 30 -
3.4
3. START-UP PROCEDURE
START-UP PROCEDURE
B-65165E/02
INITIALIZING SERVO PARAMETERS
ar
es
.co
m
/
(1) Servo amplifier module
For the initialization of servo parameters, refer to the following
manual:
FANUC AC SERVO MOTOR α series Parameter Manual
(B-65150E)
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
(2) Spindle amplifier module
For the initialization of spindle parameters, refer to the following
manual:
FANUC AC SPINDLE MOTOR α series Parameter Manual
(B-65160E)
- 31 -
B-65165E/02
ar
es
.co
m
CONFIRMATION OF THE OPERATION
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
4
START-UP PROCEDURE
/
4. CONFIRMATION OF
THE OPERATION
- 32 -
START-UP PROCEDURE
B-65165E/02
4.1
4. CONFIRMATION OF
THE OPERATION
ar
es
.co
m
Check each item according to the procedure described below.
1. Supply control power (200 VAC) to the power supply module.
2. Check the STATUS LEDs. See Section 4.1.3.
OK
Alarm occurs.
See Section 3.1 of Part II.
-s
p
3. Release the system from emergency stop state.
uc
4. Make sure that the MCC is turned on.
an
OK
NG
See Subsec. 4.1.5.
ht
tp
://
w
w
w
.g
ef
5. Check the operation of the servo and spindle motors.
- 33 -
/
POWER SUPPLY MODULE
4. CONFIRMATION OF
THE OPERATION
START-UP PROCEDURE
B-65165E/02
Check Terminal On The Printed-circuit Board
4.1.1.1
PSM, PSM-HV
Location of the check terminal
uc
-s
p
IR
IS
+24V
+5V
0V
ar
es
.co
m
/
4.1.1
an
Table 4.1.1.1 Check terminal
w
.g
ef
Check
terminal
IR
Phase L1 (phase R)
current
Phase L2 (phase S)
current
ht
tp
://
w
w
IS
+24V
+5V
0V
Control power
- 34 -
Description
The current is positive when it is input to the
amplifier.
Model
Amount of current
PSM-5.5
37.5A/1V
PSM-11
37.5A/1V
PSM-15
50A/1V
PSM-26
75A/1V
PSM-30
100A/1V
PSM-37
100A/1V
PSM-45
150A/1V
PSM-55
150A/1V
PSM-18HV 37.5A/1V
PSM-30HV 50A/1V
PSM-45HV 75A/1V
PSM-75HV 100A/1V
START-UP PROCEDURE
B-65165E/02
4.1.1.2
4. CONFIRMATION OF
THE OPERATION
PSMV-HV
-s
p
IDC
VDC
+24V
+5V
0V
ar
es
.co
m
/
Location of check terminals
an
Check
terminal
uc
Table 4.1.1.2 Check terminals
DC link current
ef
IDC
w
w
w
.g
VDC
tp
ht
Model
Amount of current
PSMV-11HV
50 A/1 V
Model
PSMV-11HV
Amount of voltage
100 V/1 V
DC link voltage
Control power
Checking The Power Supply Voltages
://
4.1.2
+24V
+5V
0V
Description
Table 4.1.2 Checking the power supply voltages
Measurement item
AC power line
voltage
Control power
voltage
Check method
Check on L1, L2, and L3 at terminal board TB2.
See Section 3.2.1.
Check on the check terminals.
Check terminal
Rating
+24V - 0V
24 V ±5%
+5V - 0V
- 35 -
5 V ±5%
4. CONFIRMATION OF
THE OPERATION
START-UP PROCEDURE
4.1.3.1
PSM, PSM-HV, and PSMV-HV
/
Checking The Status Leds
Position of the STATUS LEDs
ar
es
.co
m
4.1.3
B-65165E/02
STATUS
PIL
-s
p
ALM
uc
STATUS LEDs
On
Off
an
No.
Description
ef
The LED that is on is
indicated in black.
1
PIL
w
.g
ALM
2
PSM not ready
The main circuit is not supplied with power
(MCC OFF).
Emergency stop state
ALM
3
tp
PSM ready
The main circuit is supplied with power
(MCC ON).
The PSM is operable.
PIL
://
w
w
PIL
ht
The PIL LED (power ON indicator) is off.
Control power has not been supplied.
The control power circuit is defective. See
Section 4.1.2.
ALM
4
Alarm state
The PSM is not operable.
See Section 3.1 of Part II.
PIL
ALM
Alarm code 01 or above is
indicated.
- 36 -
START-UP PROCEDURE
B-65165E/02
4.1.3.2
4. CONFIRMATION OF
THE OPERATION
PSMR
ar
es
.co
m
/
Position of the STATUS LEDs
-s
p
STATUS
STATUS LEDs
Description
The STATUS display LED is off.
Control power has not been supplied.
The control power circuit is defective. See
Section 4.1.2.
PSMR not ready
The main circuit is not supplied with power
(MCC OFF).
Emergency stop state
3
PSMR ready
The main circuit is supplied with power
(MCC ON).
The PSMR is operable.
4
Alarm state
The PSMR is not operable.
See Section 3.1.3 of Part II.
Alarm code 02 or above is
indicated.
ht
tp
://
w
w
w
.g
ef
2
an
uc
No.
1
- 37 -
4. CONFIRMATION OF
THE OPERATION
4.1.4
START-UP PROCEDURE
B-65165E/02
The PIL LED (power ON indicator) Is Off.
/
Table 4.1.4 Check method and action
-s
p
ht
tp
://
w
w
w
.g
ef
4
an
uc
3
Check method
Action
Check that power is
connected to connector
CX1A.
(1) If the AC power input
Check whether F1 or F2
for control is
has blown. (PSM, PSMconnected to
HV)
connector CX1B by
Check whether FU1 or FU2
mistake, F2 (FU2) may
has blown. (PSMV-HV)
blow. Connect the AC
For details on how to
power input to CX1A.
replace fuses, see Chapter
(2) Replace the fuse. If
4 of Part II.
the fuse blows again
after the replacement,
replace the printed
circuit board.
Incorrect wiring
Check whether the 24-V
power output is shortcircuited and whether a
load exceeding the rating is
connected.
The power-on LED indicator (1) Replace the PSM.
Faulty power
supply circuit on PIL operates on the +5-V (2) Replace the printed
circuit board, driver
the printed circuit power supply. See
board, or power
Subsection 4.1.2 to check
board
distribution board.
the control power voltage.
ar
es
.co
m
No. Cause of trouble
1 AC power for the
control circuit not
supplied
2 Blown fuse in the
control circuit
- 38 -
START-UP PROCEDURE
B-65165E/02
4.1.5
4. CONFIRMATION OF
THE OPERATION
Checking For What Keeps The Mcc From Being Switched On
ar
es
.co
m
/
(1) The system is still in an emergency stop status.
→ Check the connection to make sure that the emergency stop
signal connected to the PSM connector CX4 and the
emergency stop signal (such as *ESP) input to the CNC are
both released.
-s
p
(2) There is a connector problem.
(a) No terminating connector is attached.
→ Check whether a terminating connector is attached to
JX1B of the SVM or SPM at the end of the connection
chain.
(b) The interface cable between JX1B of the power supply
module and JX1A of the SVM or SPM is defective.
→ Check whether the interface cable is faulty.
an
uc
(3) The power for driving the magnetic contactor is not supplied.
→ Check the voltage across the both ends of the coil of the
magnetic contactor.
CX3-<1>
tp
ht
Make sure that the contact
MCC driving relay
://
w
w
w
.g
ef
(4) The relay for driving the magnetic contactor is defective.
→ Check that a circuit between pins <1> and <3> of connector
CX3 is closed and opened.
is closed and opened.
CX3-<3>
PSM, PSMR
PSM-HV
PSMV-HV
- 39 -
4. CONFIRMATION OF
THE OPERATION
4.2
START-UP PROCEDURE
B-65165E/02
ar
es
.co
m
Check each item according to the procedure described below.
/
SERVO AMPLIFIER MODULE
1. Check the connection, and supply control power (200 VAC) to the power
supply module.
2. Check the STATUS LEDs. See Section 4.2.2.
Alarm occurs.
See Section 3.2 of Part II.
-s
p
3. Check the CNC parameters (including servo parameters), and reset
emergency stop state.
Alarm occurs.
uc
See Section 3.2 of Part II.
ht
tp
://
w
w
w
.g
ef
an
4. Check the operation of the servo motor.
- 40 -
Abnormal operation
Refer to the FANUC AC SERVO MOTOR
α series Parameter Manual (B-65150E).
START-UP PROCEDURE
B-65165E/02
4.2.1
4. CONFIRMATION OF
THE OPERATION
Check Pin Board
(1) Specifications
Order specification
A06B-6071-K290
Component
Printed circuit board: A20B-1005-0340
Cable
: A660-2042-T031#L200R0
ar
es
.co
m
/
Use of the check pin board allows you to observe the signals inside the
servo amplifier.
Remarks
Printed circuit board with check pins
20-conductor cable with a one-to-one
correspondence. Length: 200 mm
Printed circuit board: A20B-1005-0340
A20B-1005-0340
• <4>
• <9>
• <14>
• <19>
• <2>
• <7>
• <12>
• <17>
• <1>
• <6>
• <11>
• <16>
34 mm
CN2
uc
CN1
• <3>
• <8>
• <13>
• <18>
-s
p
• <5>
• <10>
• <15>
• <20>
an
100 mm
Approx. 200 mm
CN1 and CN2 are wired with a one-to-one correspondence.
The connector pin numbers correspond to the check pin numbers.
(2) Connection
Attach the cable to connector JX5 that is located on the front of
the SVM.
SVM
A20B-1005-0340
JX5
CN2
CN1
ht
tp
://
w
w
w
.g
ef
Cable: A660-2042-T031#L200R0
- 41 -
4. CONFIRMATION OF
THE OPERATION
START-UP PROCEDURE
B-65165E/02
(3) Signal output
<1>
<2>
Signal name
SVM1 SVM2 SVM3
CLR
CLR
CLR
+3.3V +3.3V +3.3V
IRL
ISL
IRM
ISM
ar
es
.co
m
Pin No.
/
SVM designed for operation with the FSSB interface
Remarks
Clear signal of the control circuit(Note)
+3.3-V power (Variations in voltage level
within ±5% are regarded as normal.)
Phase R motor current for the L axis
Phase S motor current for the L axis
Phase R motor current for the M axis
Phase S motor current for the M axis
Reference voltage
Phase R motor current for the N axis
Reference voltage
Phase S motor current for the N axis
Reference voltage
<3>
<4>
<5>
<6>
<7>
IRL
ISL
0V
IRL
ISL
IRM
ISM
0V
<8>
0V
0V
<9>
<10>
<11>
<12>
<13>
<14>
<15>
<16>
<17>
<18>
<19>
0V
0V
+24V
+15V
-15V
+5V
ITL
+24V
+15V
-15V
+5V
ITL
+24V
+15V
-15V
+5V
ITL
+24-V power
+15-V power
-15-V power
+5-V power
Phase T motor current for the L axis
ITM
ITM
Phase T motor current for the M axis
ITN
Reference voltage
Phase T motor current for the N axis
IRN
ef
an
uc
-s
p
ISN
0V
0V
0V
NOTE
Do not touch the clear signal of the control circuit;
otherwise, the servo amplifier may malfunction.
ht
tp
://
w
w
w
.g
<20>
- 42 -
START-UP PROCEDURE
B-65165E/02
4. CONFIRMATION OF
THE OPERATION
SVM designed for operation with the type A/B interface
/
ITM
ITM
Phase T motor current for the M axis
an
<9>
<10>
<11>
<12>
<13>
<14>
<15>
<16>
<17>
<18>
<19>
Clear signal of the control circuit(Note 1)
Reference voltage
Phase R motor current for the L axis
Phase S motor current for the L axis
Phase R motor current for the M axis
Phase S motor current for the M axis
Reference voltage
Phase R motor current for the N axis
Reference voltage
Phase S motor current for the N axis
Reference voltage
Reference voltage
+24-V power
+15-V power
-15-V power
+5-V power
Phase T motor current for the L axis
ar
es
.co
m
<8>
Remarks
-s
p
<1>
<2>
<3>
<4>
<5>
<6>
<7>
Signal name
SVM1 SVM2 SVM3
CLR
CLR
CLR
0V
0V
0V
IRL
IRL
IRL
ISL
ISL
ISL
IRM
IRM
ISM
ISM
0V
0V
IRN
0V
0V
ISN
0V
0V
0V
0V
0V
0V
+24V
+24V
+24V
+15V
+15V
+15V
-15V
-15V
-15V
+5V
+5V
+5V
ITL
ITL
ITL
uc
Pin No.
ITN
Reference voltage
Phase T motor current for the N axis
0V
0V
ef
<20>
ht
tp
://
w
w
w
.g
NOTE
1 Do not touch the clear signal of the control circuit;
otherwise, the servo amplifier may malfunction.
2 Part of the signal may not be output depending on
the revision of the printed circuit board.
- 43 -
4. CONFIRMATION OF
THE OPERATION
START-UP PROCEDURE
B-65165E/02
ar
es
.co
m
/
(4) Observing the motor current
You can observe an instantaneous motor current value by
observing the voltage across a reference voltage (0 V) check pin
and a motor current check pin with an oscilloscope. Note that you
cannot use a device such as a multimeter to observe correct
values.
(Instantaneous motor current value) = (voltage at motor current
check pin) × (factor for calculating motor current)
-s
p
Calculation example:
When the voltage at a motor current check pin is 3.2 V, and
the factor for calculation is 3 A/V:
Actual motor current (A) = 3.2 V × 3 A/V = 9.6 A
ht
Factor for calculating motor
current [A/V](Note 2)
0.5
1
3
5
10
15
20
32.5
60
80
90
NOTE
1 Limit of instantaneous motor current value
Values in in servo amplifier names indicate the
limits of instantaneous motor current values.
Single-axis amplifier: SVM1Double-axis amplifier: SVM2M axis
L axis
Triple-axis amplifier: SVM3N axis
tp
://
w
w
w
.g
ef
an
uc
Limit of instantaneous motor
current value [A](Note 1)
2
4
12
20
40
60
80
130
240
320
360
M axis
L axis
2 The factor for calculating the motor current of an
SVM not listed in the above table can be obtained
from the model name of the servo amplifier as
follows:
Factor for calculating the motor current = (limit of
instantaneous motor current value) ÷ 4 V
- 44 -
4. CONFIRMATION OF
THE OPERATION
START-UP PROCEDURE
B-65165E/02
Nominal voltage
+3.3-V power
+24-V power
+15-V power
-15-V power
+5-V power
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
Check pin
+3.3V
+24V
+15V
-15V
+5V
ar
es
.co
m
/
(4) Checking the power supply voltage
You can measure the voltage across a reference voltage (0V)
check pin and a power check pin with a multimeter, oscilloscope,
or the like to observe the power supply voltage for the control
circuit inside the servo amplifier. If the measured voltage is
within ±5% relative to the nominal voltage, the measured voltage
can be considered to be acceptable.
- 45 -
4. CONFIRMATION OF
THE OPERATION
4.2.2
START-UP PROCEDURE
B-65165E/02
Checking The STATUS Display
ar
es
.co
m
/
The STATUS display (a 7-segment LED) on the front of the SVM
indicates the operation status.
uc
-s
p
STATUS
Description
• The STATUS display LED is not on.
<1> Power is not turned on.
<2> Poor cable connection
Check the cable.
<3> The servo amplifier is defective.
Replace the fuse (F1) or servo amplifier.
• The control power supply is waiting for a ready signal.
w
w
w
.g
ef
an
STATUS display
://
• The servo amplifier is ready to operate.
The servo motor is supplied with power.
ht
tp
• Alarm state
If an alarm is issued in the servo amplifier, a value other
than "0" and "-" is indicated on the STATUS display
LED. See Section 3.2 of Part II.
- 46 -
START-UP PROCEDURE
B-65165E/02
4.2.3
4. CONFIRMATION OF
THE OPERATION
VRDY-OFF Alarm Indicated on the CNC Screen
ar
es
.co
m
/
When the VRDY-OFF alarm is indicated on the CNC, check the items
listed below. In addition to these causes, there are other possible
causes of VRDY-OFF. If the problem still exists after the following
items are checked, contact your FANUC service representative.
(1) Interface between modules
(a) Is a terminating dummy connector for the interface between
modules (JX1A, JX1B) attached to JX1B of the module (an
SVM or SPM) at the end of the connection chain?
uc
-s
p
(2) Emergency stop signal (ESP)
(a) Has the emergency stop signal (connector: CX4) applied to
the PSM been released? Alternatively, is the signal
connected correctly?
(b) Is the emergency stop signal line (pin 3 of connectors CX2A
and CX2B) between the PSM and SVM or SPM connected
correctly?
ht
tp
://
w
w
w
.g
ef
an
(3) MCON signal
(a) Has the ready command signal MCON been sent from the
CNC to SVM?
• Check for poor contact in the command cable between the
CNC and SVM.
• Use the servo check pin board to check the signal level.
(b) For the multi-axis amplifier, is the MCON signal sent to all
axes?
(4) External MCC
(a) Is the external MCC connected correctly and is there any
problem in the external MCC itself?
(5) Timing of turning on the power to the CNC (200 VAC, single
phase) and the PSM control power (200 VAC, single phase)
(a) Was the power to the CNC turned on at the same time when,
or after, the power for PSM control was turned on?
(6) Is there an unused axis in a multi-axis amplifier?
(a) Is a dummy connector inserted in the amplifier?
(b) Are CNC parameters set correctly?
- 47 -
4. CONFIRMATION OF
THE OPERATION
4.2.4
START-UP PROCEDURE
B-65165E/02
Servo Check Board
ar
es
.co
m
/
The servo check board receives the digital value used for control inside
the digital servo as numerical data and converts it to an analog form.
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
For details on how to connect and use the servo check board, refer to
the following:
FANUC AC SERVO MOTOR α series Parameter Manual B65150E/04 or later editions
- 48 -
START-UP PROCEDURE
B-65165E/02
4.3
4. CONFIRMATION OF
THE OPERATION
ar
es
.co
m
Check each item according to the procedure described below.
1. Supply control power (200 VAC) to the PSM, and turn on the power
to the CNC.
2. Check the STATUS display. See Subsection 4.3.1.
OK
Alarm issued.
See Section 3.4 of Part II.
-s
p
3. Has the system been used with this connection status?
No
Yes
uc
4. Prepare and check a PMC ladder. (The descriptions manual is
required.)
an
5. Set and check spindle-related parameters. (The parameter manual
is required.)
ef
6. Check the waveform on the detector. See Subsection 4.3.4.
7. Release the system from the emergency stop state.
w
.g
8. Make sure that the magnetic contactor for PSM input is turned on.
See Section 4.1.
ht
tp
://
w
w
9. Check the operation in normal operation mode (S command).
- 49 -
/
SPINDLE AMPLIFIER MODULE
4. CONFIRMATION OF
THE OPERATION
B-65165E/02
STATUS Display
PIL
ALM
ERR
STATUS
Description
No
The PIL LED (power ON indicator) is off.
indication The control power supply has not been
switched on.
The power supply circuit is defective. See
Section 3.1.2.
2.
20
For about 1.0 s after the control power
supply is switched on, the lower two digits of
the ROM series No. are indicated.
Example) 20: ROM series No. 9D20
↓
3.
04
The ROM edition number is displayed for
about 1.0 s. 01, 02, 03, and so on
correspond to A, B, C, and so on,
respectively.
Example) 04: ROM edition D
4.
-The CNC has not been switched on.
Blinking The machine is waiting for serial
communication and parameter loading to
end.
5.
-Parameter loading has ended.
Lighting The motor is not supplied with power.
6.
00
The motor is supplied with power.
7. Lighting
01 or Alarm state
above is The SPM is not operable.
displayed. See Section 3.4 of Part II.
8.
Lighting 01 or Error state
above is Incorrect parameter setting or improper
displayed. sequence.
See Section 4.3.3 of Part II.
uc
ALM
ht
tp
://
w
w
w
.g
ef
an
No.
1.
-s
p
ERR
ar
es
.co
m
STATUS
/
4.3.1
START-UP PROCEDURE
The PIL lamp is always on while the control power is being supplied.
- 50 -
START-UP PROCEDURE
B-65165E/02
Troubleshooting at Startup
4.3.2.1
The PIL LED (power-on indicator) is off.
ar
es
.co
m
4.3.2
/
4. CONFIRMATION OF
THE OPERATION
(1) When the PIL LED on the spindle amplifier module does not
come on after the main circuit breaker is turned on
2
3
4
Check method
The PSM PIL lamp is off.
The PSM PIL lamp is on.
When all connectors except
connector CX2A/B are
detached, the PIL lamp is on.
Even when all cables except
the cable attached to
connector CX2A/B are
detached, the PIL lamp does
not come on.
Action
Check the cable attached to
CX1A of PSM.
Check the cabling.
Replace or repair the cable.
If the fuse blows, the printed
circuit board may be faulty.
Replace the SPM.
Replace the SPM.
4.3.2.2
an
uc
5
Cause of trouble
The 200-V control power is not
supplied.
The cable attached to
connector CX2A/B is
defective.
The power is externally
connected to 0 V, GND, or the
like.
There is a blown fuse on the
printed circuit board.
(A06B-6102-Hxxx, 6104-Hxxx)
The printed circuit board is
defective.
-s
p
No.
1
The STATUS display is blinking with "--."
w
.g
ef
(1) When no spindle communication alarm message is indicated on
the CNC
Check whether the CNC software option setting or bit setting is
correct.
(2) When a communication alarm message is indicated on the CNC
Cause of trouble
The SPM switch setting is
incorrect.
For A06B-6072-Hxxx, A06B6078-H215 to H230, and
A06B-6078-H315 to H330 only
2
The cable is incorrect.
3
The cable is defective.
4
The printed circuit board is
defective.
ht
tp
://
w
w
No.
1
Check method
When a second SPM is
connected, switch S1 is set to
ON.
When no other SPM is
connected, switch S1 is set to
OFF.
Note that the cable used for
connecting an electric/optical
adapter and the cable
connected directly to the CNC
differ in specifications.
Check whether the cable is
broken.
Check for short-circuit in the
connector.
Action
Correct the switch setting.
Replace the cable with a
correct cable.
Repair or replace the cable.
Replace the SPM.
- 51 -
4. CONFIRMATION OF
THE OPERATION
4.3.2.3
START-UP PROCEDURE
B-65165E/02
The motor does not turn.
FS0
G229
G230
FS15
G227
G226
FS16
#7
G070 MRDYA
G071
#6
#5
SFRA
ar
es
.co
m
/
(1) When "--" is indicated on the STATUS display of the SPM
Check whether spindle control signals are input. (An example for
the first spindle is given below.)
#4
SRVA
#3
#2
#1
#0
*ESPA
(2) When "00" is indicated on the STATUS display of the SPM
No spindle speed command is input.
Refer to "FANUC AC SPINDLE MOTOR α series
Parameter Manual," and check related parameters.
A specified speed cannot be obtained.
uc
4.3.2.4
-s
p
(3) When an alarm number is indicated on the SPM
See the description of the alarm number in Section 3.4 of Part II.
ef
an
(1) When the speed always differs from a specified speed
Check parameters.
Refer to "FANUC AC SPINDLE MOTOR α series
Parameter Manual," and check related parameters.
ht
tp
://
w
w
w
.g
(2) When an alarm number is indicated on the SPM
See the description of the alarm number in Section 3.4 of Part II.
- 52 -
START-UP PROCEDURE
B-65165E/02
When cutting is not performed, the spindle vibrates, making
noise.
/
4.3.2.5
4. CONFIRMATION OF
THE OPERATION
ar
es
.co
m
(1) The spindle vibrates only when the spindle speed has reached or is
at a particular speed level.
Check whether the spindle also vibrates when the motor is turning
by inertia. If noise is unchanged, investigate the source of
mechanical vibration. There are several methods to turn the
spindle by inertia as explained below. Because these methods
involve machine sequences, consult with the machine tool
builder.
Setting spindle control signal MPOF (FS16 for the first
spindle: G73#2, FS15 for the first spindle: G228#2) to 1
immediately causes the spindle to turn by inertia.
B.
Set ALSP (FS16: bit 2 of parameter No. 4009, FS15 for the
first spindle: bit 2 of parameter No. 3009) to 1. Then, when
the power to the CNC is turned off during spindle rotation,
the spindle turns by inertia. (On the spindle amplifier
module, alarm 24 is indicated.)
an
uc
-s
p
A.
(2) When noise is generated at the time the motor is stopped or at any
time
See Subsection 4.3.4 of this part, and check and adjust the
waveform of the spindle sensor.
w
w
w
.g
ef
A.
C.
Adjust the velocity loop gain and so forth.
For details, refer to "FANUC AC SPINDLE MOTOR α
series Parameter Manual."
Refer to "FANUC AC SPINDLE MOTOR α series Parameter
Manual," and adjust parameters.
ht
tp
Check that the motor part number matches its parameters.
For details, refer to "FANUC AC SPINDLE MOTOR α
series Parameter Manual."
An overshoot or hunting occurs.
://
4.3.2.6
B.
- 53 -
4. CONFIRMATION OF
THE OPERATION
B-65165E/02
Cutting power weakens or acceleration/deceleration slows
down.
A.
ar
es
.co
m
(1) When the load meter does not indicate the maximum output
/
4.3.2.7
START-UP PROCEDURE
A mechanical element such as a belt slip may occur.
(2) When the load meter indicates the maximum output
A.
FS16
G070
#7
#6
#5
#4
#3
#2
#1
#0
TLMHA TLMLA
B.
Check that the motor part number matches its parameters.
For details, refer to "FANUC AC SPINDLE MOTOR α
series Parameter Manual."
C.
Check whether the output limit pattern is set incorrectly.
For details, refer to "FANUC AC SPINDLE MOTOR α
series Parameter Manual."
-s
p
FS15
G227
ht
tp
://
w
w
w
.g
ef
an
uc
FS0
G229
Check whether the torque limit signal is input incorrectly.
(An example for the first spindle is given below.)
- 54 -
START-UP PROCEDURE
B-65165E/02
4.3.3
4. CONFIRMATION OF
THE OPERATION
Status Error Indication Function
status
The error LED
(yellow) lights.
ar
es
.co
m
/
When there is a sequence or parameter error, the error LED (yellow) in
the display section of the spindle amplifier module (SPM) goes on with
an error code displayed. This can ease troubleshooting at the time of
machine startup.
An error code is indicated. (from 01)
Description
Although neither *ESP (emergency
stop signal) (there are two types of
signals, a PMC signal and PSM contact
signal) nor MRDY (machine ready
signal) has been input, SFR (forward
rotation signal), SRV (reverse rotation
signal), or ORCM (orientation
command) is input.
When the spindle motor is equipped
with a high-resolution magnetic pulse
coder (Cs sensor) (FS16i: bits 6 and 5
of parameter No.4001 = 0, 1), 128 λ/rev
must be set for the speed detector
(FS16i: bits 2, 1, and 0 of parameter
No. 4011 = 0, 0, 1). However, other
than 128 λ/rev is set. In this case, the
motor is not activated.
Although the use of a high-resolution
magnetic pulse coder (FS16i: bit 5 of
parameter No. 4001 = 1) or the use of
the Cs contour control function by the α
sensor (FS16i: bit 4 of parameter No.
4018 = 1) is not specified, a Cs control
command is input. In this case, the
motor is not activated.
Although the parameter for using the
position coder signal (FS16i: bit 2 of
parameter No. 4001 = 1) is not set, a
command for servo mode (rigid tapping
or spindle positioning) or spindle
synchronization is input. In this case,
the motor is not activated.
Although no orientation option is set, an
orientation command (ORCM) is input.
03
04
ht
tp
://
w
w
w
.g
ef
02
an
uc
No.
01
-s
p
When the spindle amplifier module does not operate for a certain
function, check whether the status error is indicated. The status error
number does not appear on the CNC screen.
05
(Continued)
- 55 -
Action
Check the *ESP and MRDY
sequences. (For MRDY, pay
attention to the parameter that
specifies whether to use the
MRDY signal (FS16i: bit 0 of
parameter No. 4001).)
Check the speed detector
parameter of the spindle motor
(FS16i: bits 2, 1, and 0 of
parameter No. 4011).
Check the parameters of the
detector for Cs contour control
(FS16i: bit 5 of parameter No.
4001 and bit 4 of parameter No.
4018).
Check the parameter of the
position coder signal (FS16i: bit 2
of parameter No. 4001).
Check the software option for
orientation.
4. CONFIRMATION OF
THE OPERATION
START-UP PROCEDURE
09
10
11
ef
w
.g
13
15
16
ht
tp
://
w
w
14
17
/
Check the sequence (SPSYC,
SFR, and SRV).
Do not specify another operation
mode during execution of the Cs
contour control command. Before
entering another mode, cancel the
Cs contour control command.
In servo mode (rigid tapping or spindle Do not specify another operation
mode during execution of the
positioning), another operation mode
servo mode command. Before
(Cs contour control, spindle
entering another mode, cancel
synchronization, or orientation) is
servo mode.
specified.
Do not specify another operation
During spindle synchronization,
mode during execution of the
another operation mode (Cs contour
spindle synchronization
control, servo mode, or orientation) is
command. Before entering
specified.
another mode, cancel the spindle
synchronization command.
Do not specify another operation
When an orientation specification is
specified, another operation mode (Cs mode during execution of the
orientation command. Before
contour control, servo mode, or
entering another mode, cancel the
synchronization control) is specified.
orientation command.
The SFR signal and SRV signal are
Input one of the SFR and SRV
input at the same time.
signals.
Check the setting of the
Although the parameter to use the
differential mode function (FS16i: bit 5 parameter (FS16i: bit 5 of
parameter No. 4000) and the PMC
of parameter No. 4000 = 1) is set, Cs
signal (CON).
axis contour control is specified.
Although the parameter not to use the Check the setting of the
differential mode function (FS16i: bit 5 parameter (FS16i: bit 5 of
parameter No. 4000) and the PMC
of parameter No. 4000 = 0) is set, a
signal (DEFMD).
differential speed mode command
(DEFMD) is input.
Check the parameter settings
The parameter settings for the speed
(FS16i: bits 2, 1, and 0 of
detector (FS16i: bits 2, 1, and 0 of
parameter No. 4011).
parameter No. 4011) are invalid.
(There is no speed detector that
matches the settings.)
an
12
ar
es
.co
m
08
Action
Check the software option for
spindle output switching and the
power line status signal (RCH).
Check the sequence (CON, SFR,
and SRV).
Check the sequence (SFR and
SRV).
-s
p
07
Description
Although no output switching option is
set, low-speed winding is selected
(RCH = 1).
Although Cs contour control mode is
specified, neither SFR nor SRV is input.
Although servo mode (rigid tapping or
spindle positioning) is specified, neither
SFR nor SRV is input.
Although spindle synchronization mode
is specified, neither SFR nor SRV is
input.
In Cs contour control mode, another
operation mode (servo mode, spindle
synchronization, or orientation) is
specified.
uc
No.
06
B-65165E/02
- 56 -
4. CONFIRMATION OF
THE OPERATION
START-UP PROCEDURE
B-65165E/02
(Continued)
19
Do not specify another operation
mode during execution of the
orientation command. Before
entering another mode, cancel the
orientation command.
Check the parameter settings
When the use of the slave operation
(FS16i: bit 5 of parameter No.
mode function (FS16i: bit 5 of
parameter No. 4014 = 1) is set, the use 4001, bit 5 of parameter No. 4014,
and bit 4 of parameter No. 4018).
of a high-resolution magnetic pulse
coder (FS16i: bit 5 of parameter No.
4001 = 1) or the use of the Cs contour
control function by the α sensor (FS16i:
bit 4 of parameter No. 4018 = 1) is set.
These settings cannot be made at the
same time.
During position control (such as servo Input the slave operation mode
command (SLV) in normal
mode and orientation), a slave
operation mode.
operation mode command (SLV) is
input.
In slave operation mode (SLVS = 1), a Input the position control
command in normal operation
position control command (such as
mode.
servo mode and orientation) is input.
Although the parameter not to use the Check the parameter setting
slave operation mode function (FS16i: (FS16i: bit 5 of parameter No.
bit 5 of parameter No. 4014 = 0) is set, 4014) and the PMC signal (SLV).
the slave operation mode command
(SLV) is input.
Check the PMC signal (INCMD).
After orientation is performed in
incremental mode (INCMD = 1) first, an Perform an absolute position
absolute position command (INCMD = command orientation first.
0) is input next.
Check the spindle amplifier
Although the spindle amplifier is not
SPM type 4, the use of the Cs contour specification and parameter
control function by the α sensor (FS16i: setting (FS16i: bit 4 of parameter
bit 4 of parameter No. 4018 = 1) is set. No. 4018).
uc
ef
22
an
21
w
.g
23
25
ht
tp
://
w
w
24
/
Action
Check the parameter setting
(FS16i: bit 2 of parameter No.
4001) and the PMC signal
(ORCM).
-s
p
20
Description
Although the parameter not to use the
position coder signal (FS16i: bit 2 of
parameter No. 4001 = 0) is set, a
position coder orientation command
(ORCMA) is input.
During magnetic sensor orientation,
another operation mode is specified.
ar
es
.co
m
No.
18
- 57 -
4. CONFIRMATION OF
THE OPERATION
4.3.4
START-UP PROCEDURE
B-65165E/02
Checking The Feedback Signal Waveform
ar
es
.co
m
/
First, refer to Subsection 9.2.3 of "FANUC SERVO AMPLIFIER α
series Descriptions" (B-65162E), and make sure that the spindle
sensors and other detectors are connected at the correct points. Next,
see the table given below to find the corresponding check terminal
names on the check board from the sensor connector connection points.
Do not observe feedback signals before the parameters for the detectors
that are set. Phase A, B, and Z signals may not be output correctly until
the parameters are loaded from the CNC.
Signals input to the SPM and corresponding check terminals on the
check board
(1) SPM type 1, type 2, and type 4
JY3
pin 5, 6
pin 7, 8
PA4
PB4
PS1
EXTSC1
LSA1
MSA1
PAD
PBD
w
.g
JY4
pin 3, 4
pin 17, 19
pin 1, 2
PA2
PB2
Phase A:
Phase B:
Phase Z:
Phase Z:
PA3
PB3
PS2
PSD
pin 3, 4
pin 17, 19
pin 1, 2
pin 1, 2
ht
tp
PA3
PB3
PSD
Phase A: pin 5, 6
Phase B: pin 7, 8
://
JY5
w
w
Phase A: pin 3, 4
Phase B: pin 17, 19
Phase Z: pin 1, 2
-s
p
Main sensors
M, MZ, and BZ sensors
Low resolution side of the high-resolution
magnetic pulse coder (128 to 384 λ)
High resolution side of the high-resolution
magnetic pulse coder (1000 to 3000 λ)
MZ and BZ sensors (one-rotation signal)
Proximity switch (external one-rotation signal)
Magnetic sensor (LSA signal)
Magnetic sensor (MSA signal)
α position coder (1024 p)
Low resolution side of the high-resolution
position coder (1024 p)
High resolution side of the high-resolution
position coder (3000 λ)
α position coder (one-rotation signal)
High-resolution position coder (one-rotation
signal)
M, MZ, and BZ sensors
Low resolution side of a high-resolution
magnetic pulse coder (128 to 384 λ)
α position coder S (1024 λ)
High resolution side of a high-resolution
magnetic pulse coder (1000 to 3000 λ)
MZ and BZ sensors (one-rotation signal)
α position coder S (one-rotation signal)
High-resolution magnetic pulse coder (onerotation signal)
uc
Phase A:
Phase B:
Phase Z:
pin 18
pin 1, 3
pin 5, 14
Phase A:
Phase B:
Check
terminal name
PA1
PB1
an
Connector pin
signal
Phase A: pin 5, 6
Phase B: pin 7, 8
ef
SPM input
connector
JY2
*1
Remarks
For type 2 only
*1
Parameter setting
For type 2 only
Parameter setting
For types 2 and 4
only
For type 2 only
For type 4 only
Parameter setting
This check terminal is provided for A20B-1005-0740 only. With
A20B-2001-0830, MSA is observed on CH1 or CH2.
Only for SMPs of which the specification is A06B-6078-H315 to 330
JY6
Phase A: pin 5, 6
Phase B: pin 7, 8
PA2
PB2
M, MZ, and BZ sensors
- 58 -
For type 2 only
4. CONFIRMATION OF
THE OPERATION
START-UP PROCEDURE
B-65165E/02
(2) SPM type 3
Main side
MZ and BZ sensors (one-rotation signal)
M, MZ, and BZ sensors
Main side
Sub side
MZ and BZ sensors (one-rotation signal)
α position coder (1024 p)
Sub side
When the main side
is selected by
spindle switching
control, signals are
output on JY4.
When the sub side
is selected, signals
are output on JY8.
Parameters must be
set correctly.
When the main side
is selected by
spindle switching
control, signals are
output on JY4.
When the sub side
is selected, signals
are output on JY8.
Parameters must be
set correctly.
Main side
Main side
Main side(*1)
For A20B-10050740 only
Sub side
Sub side
Sub side(*1)
For A20B-10050740 only
α position coder (one-rotation signal)
pin 18
pin 1, 3
pin 5, 14
ef
JY7
Proximity switch (external one-rotation signal)
Magnetic sensor (LSA signal)
Magnetic sensor (MSA signal)
EXTSC2
LSA2
MSA2
Proximity switch (external one-rotation signal)
Magnetic sensor (LSA signal)
Magnetic sensor (MSA signal)
*1
With A20B-2001-0830, MSA is observed on CH1 or CH2.
ht
tp
://
EXTSC1
LSA1
MSA1
w
.g
pin 18
pin 1, 3
pin 5, 14
w
w
JY3
/
PSD
M, MZ, and BZ sensors
Remarks
ar
es
.co
m
Phase Z: pin 1, 2
and
Phase Z: pin 1, 2
Main sensors
an
JY4 or
JY8
Check
terminal name
PA1
PB1
PS1
PA2
PB2
PS2
PAD
PBD
-s
p
JY6
Connector pin
signal
Phase A: pin 5, 6
Phase B: pin 7, 8
Phase Z: pin 1, 2
Phase A: pin 5, 6
Phase B: pin 7, 8
Phase Z: pin 1, 2
Phase A: pin 5, 6
Phase B: pin 7, 8
and
Phase A: pin 5, 6
Phase B: pin 7, 8
uc
SPM input
connector
JY2
- 59 -
4. CONFIRMATION OF
THE OPERATION
B-65165E/02
M sensor
Measurement
condition
The speed must be
-1
1500 min or less.
Sample waveform
Waveforms of phase
A and phase B
For sub side
selected by spindle
switching:
Input on JY6 side
PA2, PB2
/
Measurement
location
Input on JY2 side
PA1, PB1
ar
es
.co
m
4.3.4.1
START-UP PROCEDURE
Vpp
PA1 (PA2)
Voffs
PB1 (PB2)
-s
p
0V
For the SPM type 4 or SPM of which the specification is A06B-6102-Hxxx#H520 or A06B-6104-Hxxx#H520
For SPMs other than the above
Measurement method
ef
Specification
0.64 to 0.90 Vp-p
2.5 V ±90 mV
Use the DC range of a digital
voltmeter.
Use the DC range of a digital
voltmeter.
ht
tp
://
w
w
w
.g
Measurement item
Vpp
Voffs
Measurement method
uc
Specification
0.36 to 0.50 Vp-p
2.5 V ±100 mV
an
Measurement item
Vpp
Voffs
- 60 -
Adjustment method
Adjustment is normally unnecessary.
Level check is possible, but
adjustment is not possible.
Adjustment method
Adjustment is normally unnecessary.
Level check is possible, but
adjustment is not possible.
START-UP PROCEDURE
B-65165E/02
MZ and BZ sensors
Measurement
condition
The speed must be
-1
1500 min or less.
For SPM type 4:
Input on JY5 side
PA2, PB2
Rotation direction: CW
Sample waveform
Waveforms of phase
A and phase B
Vpp
PA1 (PA2)
Detection gear
/
Measurement
location
Input on JY2 side
PA1, PB1
ar
es
.co
m
4.3.4.2
4. CONFIRMATION OF
THE OPERATION
Vphase
Voffs
PB1 (PB2)
Motor
For sub side
selected by spindle
switching:
Input on JY6 side
PA2, PB2
CW
0V
-s
p
Ripples of phase A and
phase B
PA1, PB1 (PA2, PB2)
uc
Vrip
Waveform of
phase Z
an
(Z - *Z)
w
.g
ef
Vpz
Voffz
0V
w
w
For the SPM type 4 or SPM of which the specification is A06B-6102-Hxxx#H520 or A06B-6104-Hxxx#H520
Specification
0.5 to 1.2 Vp-p
2.5 V ±100 mV
Vphase
Vrip
Vpz
90 ±3°
< 70 mV
> 1.0 V
tp
://
Measurement item
Vpp
Voffs, Voffz
Measurement method
Use the DC range of a digital
voltmeter.
Adjustment method
Normally, the MZ sensor need not be
adjusted. For Voffs and Voffz, only
level check is possible, but
adjustment is not possible.
For SPMs other than the above
Specification
0.66 to 0.93 Vp-p
2.5 V ±272 mV
Vphase
Vrip
Vpz
90 ±3°
< 70 mV
> 1.0 V
ht
Measurement item
Vpp
Voffs, Voffz
Measurement method
Use the DC range of a digital
voltmeter.
- 61 -
Adjustment method
Normally, the MZ sensor need not be
adjusted. For Voffs and Voffz, only
level check is possible, but
adjustment is not possible.
4. CONFIRMATION OF
THE OPERATION
B-65165E/02
MZ sensor for α 0.5 (A06B-0866-B390) (old specification)
Measurement
condition
The speed must be
-1
1500 min or less.
Sample waveform
Waveforms of phase
A and phase B
Vpp
PA1 (PA2)
For sub side
Rotation direction: CW
Detection gear
selected by spindle
switching:
Input on JY6 side
Motor
PA2, PB2
/
Measurement
location
Input on JY2 side
PA1, PB1
ar
es
.co
m
4.3.4.3
START-UP PROCEDURE
Vphase
Voffs
PB1 (PB2)
CW
-s
p
0V
Waveform of
phase Z
(Z - *Z)
uc
Vpz
0V
ef
an
Voffz
For the SPM type 4 or SPM of which the specification is A06B-6102-Hxxx#H520 or A06B-6104-Hxxx#H520
Measurement method
Use the DC range of a digital
voltmeter.
90 ±3°
> 1.0 V
w
w
Vphase
Vpz
Specification
0.5 to 1.2 Vp-p
2.5 V ±100 mV
w
.g
Measurement item
Vpp
Voffs,Voffz
Adjustment method
Normally, the MZ sensor need not be
adjusted. For Voffs and Voffz, only
level check is possible, but
adjustment is not possible.
For SPMs other than the above
Specification
0.50 to 1.45 Vp-p
2.5 V ±295 mV
Voffz
2.5 V ±500 mV
tp
://
Measurement item
Vpp
Voffs
ht
Vphase
Vpz
Measurement method
Use the DC range of a digital
voltmeter.
Use the DC range of a digital
voltmeter.
90 ±3°
> 2.0 V
- 62 -
Adjustment method
Normally, the MZ sensor need not be
adjusted. For Voffs and Voffz, only
level check is possible, but
adjustment is not possible.
START-UP PROCEDURE
B-65165E/02
4.3.4.4
4. CONFIRMATION OF
THE OPERATION
High-resolution magnetic pulse coder
ar
es
.co
m
/
After mounting a high-resolution magnetic pulse coder on the machine,
check waveforms. If a measurement value exceeds the specified range,
adjustment is required.
After mounting the sensor, you should check waveforms before
installing components such as a pulley, drawbar, and brake to make
adjustment easier.
(1) Adjusting check pins on the preamplifier
Signal on the low-resolution side 128 to 384 λ
Measurement
Measurement
location
condition
Check pins A3 and The speed must be 500
-1
min or less.
B3 on the
preamplifier
Rotation direction: CW
Sample waveform
Waveforms of phase
A and phase B
Vpp
-s
p
A3
Detection gear
uc
Voffs
Motor
CW
B3
an
0V
ef
Signal on the high-resolution side 1000 to 3000 λ
w
.g
Measurement
Measurement
location
condition
Check pins A1 and The speed must be 500
-1
min or less.
B1 on the
preamplifier
Rotation direction: CW
Waveforms of phase
A and phase B
w
w
Voffs2
B1
://
Motor
tp
ht
Vpp2
Vpp2
A1
Detection gear
Measurement item
Vpp
Sample waveform
CW
Specification
0.36 to 0.50 Vp-p
0V
Measurement method
0.80 to 1.0 Vp-p
Voffs
2.5 V ±50 mV
Voffs2
2.5 V ±10 mV
Use the DC range of a digital
voltmeter.
Use the DC range of a digital
voltmeter.
- 63 -
Adjustment method
Adjust potentiometers A3G and B3G
on the preamplifier.
Adjust potentiometers A1G and B1G
on the preamplifier.
Adjust potentiometers A3O and B3O
on the preamplifier.
Adjust potentiometers A1O and B1O
on the preamplifier.
4. CONFIRMATION OF
THE OPERATION
START-UP PROCEDURE
B-65165E/02
One-rotation signal
Measurement
Measurement
location
condition
Check pin Z on the The speed must be 500
-1
preamplifier
min or less.
Waveform of
phase Z
2.5 V (VRM)
Z
0V
Specification
Z1 > 60 mV
Z2 > 60 mV
Measurement method
uc
an
ef
w
.g
w
w
://
tp
ht
- 64 -
Z2
Z1
Adjustment method
Adjust potentiometer ZO on the
preamplifier so that the value of Z1
and that of Z2 are almost the same.
-s
p
Measurement item
Z1, Z2
ar
es
.co
m
/
Sample waveform
4. CONFIRMATION OF
THE OPERATION
START-UP PROCEDURE
B-65165E/02
ar
es
.co
m
/
(2) Adjusting check pins on the check board
For the high-resolution magnetic pulse coder built into the motor,
waveforms are factory-adjusted. If a waveform exceeds a
specified value, however, adjust potentiometers on the
preamplifier.
Signal on the low-resolution side 128 to 384 λ
Measurement
location
Input on JY2 side
PA1, PB1
Measurement
condition
The speed must be 500
-1
min or less.
Input on JY5 side
PA2, PB2
Rotation direction: CW
Sample waveform
Waveforms of phase
A and phase B
Vpp
PA2 (PA1)
Detection gear
Voffs
PB2 (PB1)
-s
p
Motor
CW
uc
0V
Measurement
condition
The speed must be 500
-1
min or less.
Input on JY5 side
PA3, PB3
Rotation direction: CW
Sample waveform
Waveforms of phase
A and phase B
Vpp2
w
.g
ef
Measurement
location
Input on JY2 side
PA4, PB4
an
Signal on the high-resolution side 1000 to 3000 λ
Detection gear
PA3 (PA4)
Voffs2
PB3 (PB4)
Motor
w
w
CW
0V
://
For the SPM type 4 or SPM of which the specification is A06B-6102-Hxxx#H520 or 6104-Hxxx#H520
tp
Measurement item
Vpp
Measurement method
0.80 to 1.0 Vp-p
ht
Vpp2
Specification
0.36 to 0.50 Vp-p
- 65 -
Adjustment method
Adjust potentiometers A3G and B3G
on the preamplifier.
Adjust potentiometers A1G and B1G
on the preamplifier.
4. CONFIRMATION OF
THE OPERATION
START-UP PROCEDURE
B-65165E/02
For the SPM type 2
Vpp2
1.20 to 1.51 Vp-p
Voffs
2.5 V ±24 mV
Voffs2
2.5 V ±15 mV
Measurement method
Adjustment method
Adjust potentiometers A3G and B3G
on the preamplifier.
Adjust potentiometers A1G and B1G
on the preamplifier.
Adjust potentiometers A3O and B3O
on the preamplifier.
Adjust potentiometers A1O and B1O
on the preamplifier.
/
Specification
0.86 to 1.20 Vp-p
Use the DC range of a digital
voltmeter.
Use the DC range of a digital
voltmeter.
ar
es
.co
m
Measurement item
Vpp
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
NOTE
Adjust the one-rotation signal while checking the
waveform on the preamplifier.
- 66 -
START-UP PROCEDURE
B-65165E/02
4.3.5
4. CONFIRMATION OF
THE OPERATION
Spindle Check Board
<2> Observe internal data.
4.3.5.1
Spindle check board specifications
ar
es
.co
m
<1> Observe signal waveforms.
/
When connecting the check board, you can:
-s
p
There are two types of spindle check boards: Check boards for the α
series and for the D series. These types of check boards are not
compatible. Select a spindle check board according to the drawing
number of the SPM used.
Items that vary depending on the type of check board are described
separately by indicating the printed circuit board drawing numbers of
check boards.
TYPE3
A06B-6088-H4**#H500
A06B-6072-H051
A20B-1005-0740
ht
tp
://
w
w
w
.g
ef
A06B-6078-H001
Drawing No. of
Applicable SPM
printed circuit board
A20B-2001-0830
α series (all series after CE-marked products, and part
of series before CE-marked products)
TYPE1, TYPE4
A06B-6078-H102#H500, -H106#H500, -H111#H500
A06B-6078-H202#H500, -H206#H500, -H211#H500
A06B-6088-H2**#H500, H1**#H500
A06B-6092-H2**#H500, H1**#H500
A06B-6102-H2**#H520, H1**#H520
A06B-6104-H2**#H520, H1**#H520
TYPE2
A06B-6078-H302#H500, -H306#H500, -H311#H500
A06B-6088-H3**#H500
A06B-6092-H3**#H500
an
Specification
uc
Table 4.3.5.1 Spindle check board specifications
- 67 -
αC series
A06B-6082-Hxxx#H510, 511, 512
α series (part of series before CE-marked products)
TYPE1
A06B-6078-H215#H500, -H222#H500, -H226#H500,
-H230#H500
TYPE2
A06B-6078-H315#H500, -H322#H500, -H326#H500,
-H330#H500
TYPE3
A06B-6078-H411#H500, -H415#H500, -H422#H500,
-H426#H500, -H430#H500
D series (all series)
4. CONFIRMATION OF
THE OPERATION
4.3.5.2
START-UP PROCEDURE
B-65165E/02
Check board connection
/
(1) A06B-6078-H001 (A20B-2001-0830)
SPMC
ar
es
.co
m
SPM
SPM-HV
JX4
JY1
JY1
Spindle check
board
JY1A JX4A
Spindle check
board
JY1A JX4A
A20B-2001-0830
A20B-2001-0830
JY1B JX4B
JY1B JX4B
Output equivalent to JX4
-s
p
Output equivalent to JY1
SPM
an
JX4
uc
(2) A06B-6072-H051 (A20B-1005-0740)
Spindle check
board
JY1A JX4A
A20B-1005-0740
w
.g
ef
JY1
JY1B
ht
tp
://
w
w
Output equivalent
to JY1
- 68 -
Output equivalent
to JY1
START-UP PROCEDURE
B-65165E/02
4.3.5.3
4. CONFIRMATION OF
THE OPERATION
Check terminal output signals
ar
es
.co
m
/
(1) A06B-6078-H001 (A20B-2001-0830) check terminal output
signals
Signal name
Phase A sine wave signal 1
Phase B sine wave signal 1
Phase Z sine wave signal 1
Phase A sine wave signal 2
Phase B sine wave signal 2
Phase Z sine wave signal 2
Phase A sine wave signal 3
Phase B sine wave signal 3
Phase A sine wave signal 4
Phase B sine wave signal 4
Analog override command
+15 VDC power check
+5 VDC power check
-15 VDC power check
0V
ef
an
uc
-s
p
Check terminal
Signal name
Check terminal
LM
Load meter signal
PA1
SM
Speed meter signal
PB1
PS1
CH1
Analog output for internal data
observation
(Phase U current: IU. See 4.3.6.8 (3).)
CH2
Analog output for internal data
PA2
observation
-1
(Motor speed TSA: 1638 min /V)
CH1D
Output for internal data bit observation
PB2
CH2D
Output for internal data bit observation
PS2
VRM
Sensor reference voltage
PA3
LSA1
Magnetic sensor output LSA signal
PB3
(main)
EXTSC1
External one-rotation signal (main)
PA4
LSA2
Magnetic sensor output LSA signal (sub)
PB4
EXTSC2
External one-rotation signal (sub)
OVR2
PAD
Phase A of position coder signal output
15V
PBD
Phase B of position coder signal output
5V
PSD
Phase Z of position coder signal output
-15V
GND
ht
tp
://
w
w
w
.g
Check terminal arrangement
PIL
LM
CH1
LSA2
Display
LSA1
SM
CH1D
EXTSC2
EXTSC1
PAD
CH2D
PBD
PA3
VRM
CH2
0V
0V
Operation
PA2
PSD
buttons
PA1
PB3
PB2
PB1
5V
MODE
15V
DATA
SET
UP
PA4
PS2
PS1
0V
-15V
- 69 -
DOWN
PB4
0V
OVR2
4. CONFIRMATION OF
THE OPERATION
START-UP PROCEDURE
B-65165E/02
LSA1
EXTSC1
MSA2
Signal name
Phase A sine wave signal 1
Phase B sine wave signal 1
Phase Z sine wave signal 1
Phase A sine wave signal 2
Phase B sine wave signal 2
Phase Z sine wave signal 2
Phase A sine wave signal 3
Phase B sine wave signal 3
Phase A sine wave signal 4
Phase B sine wave signal 4
Analog override command
+24 VDC power check
+15 VDC power check
5 VDC power check
0V
uc
-s
p
LSA2
EXTSC2
PAD
PBD
PSD
Signal name
Check terminal
Load meter signal
PA1
Speed meter signal
PB1
Phase U current(*1)
PS1
Phase V current(*1)
PA2
DC link voltage
PB2
Sensor reference voltage
PS2
Magnetic sensor output MSA signal
PA3
(main)
Magnetic sensor output LSA signal
PB3
(main)
External one-rotation signal (main)
PA4
Magnetic sensor output MSA signal
PB4
(sub)
Magnetic sensor output LSA signal (sub)
OVR2
External one-rotation signal (sub)
24V
Phase A of position coder signal output
15V
Phase B of position coder signal output
5V
Phase Z of position coder signal output
GND
ar
es
.co
m
Check terminal
LM
SM
IU
IV
VDC
VRM
MSA1
/
(2) A06B-6072-H051 (A20B-1005-0740) check terminal output
signals
an
Check terminal arrangement
ef
PIL
LM
IU
Display
w
.g
LSA2
SM
LSA1
IV
MSA2
MSA1
EXTSC2
EXTSC1
VRM
w
w
0V
PBA
PA2
PBB
VDC
0V
PA3
Operation
buttons
PA1
PB2
PSB
MODE
PB1
UP
://
0V
PS1
DOWN
15V
0V
24V
OVR2
ht
tp
PB4
DATA
SET
The value measured on the IU pin
corresponds to the actual current as follows:
5V
PS2
PA4
*1
PB3
- 70 -
Model
SPM-15
Conversion value (A/V)
50
SPM-22
66.7
SPM-26
100
SPM-30
133
START-UP PROCEDURE
B-65165E/02
4. CONFIRMATION OF
THE OPERATION
Observing Data Using the Spindle Check Board
4.3.6.1
Overview
ar
es
.co
m
/
4.3.6
By using the check board, you can convert digital signals used for
control in the spindle amplifier module to analog voltage, and observe
the conversion result with an oscilloscope. The internal data can be
indicated also with the five-digit display.
• A20B-2001-0830
This model has two analog output channels (CH1 and CH2) at
which the internal data (with output of -5 V to +5 V) can be
observed. It also has CH1D and CH2D at which specific bits such
as data bits can be observed.
Major characteristics
an
4.3.6.2
uc
-s
p
• A20B-1005-0740
This model outputs internal data (output of 0 to 11 V) at terminals
LM and SM using the analog output circuit for the load meter (LM)
and speedometer (SM).
ht
tp
://
w
w
w
.g
ef
Item
A20B-2001-0830
Measurement point CH1, CH2
CH1D, CH2D
Output voltage
-5 to +5 V
H: 2 Vmin
range
L: 0.8 Vmax
Resolution
About 39 mV
(10 V/256)
Output impedance 10 kΩmax
10 kΩmax
- 71 -
A20B-1005-0740
LM, SM
0 to 11 V
About 43 mV(11 V/256)
10 kΩmax
4. CONFIRMATION OF
THE OPERATION
4.3.6.3
START-UP PROCEDURE
B-65165E/02
Observation method
Measurement point
Channel 1
Check terminal
A20B-2001-0830
A20B-1005-0740
CH1
LM
CH1D, data bit 0
CH2
SM
CH2D, data bit 0
-s
p
Channel 2
ar
es
.co
m
/
By setting data using four DIP switches on the check board, you can
output internal data to the five-digit display, analog voltage output
circuit, channels 1 and 2 (LM and SM or CH1 and CH2).
Data on channels 1 and 2 is the one from an 8-bit D/A convertor.
The correspondence between channel 1/2 and the check terminal is
listed below.
an
uc
NOTE
When using printed-circuit board A20B-1005-0740,
set DIP switches S2 and S3 on the spindle amplifier
module front panel to OFF. After observation, set
them to ON.
This operation is not necessary when you use
printed-circuit board A20B-2001-0830.
ht
tp
://
w
w
w
.g
ef
DIP switch
S2, S3
- 72 -
ON position
Output voltage is
filtered out.
OFF position
Output voltage is not
filtered out.
START-UP PROCEDURE
B-65165E/02
4.3.6.4
4. CONFIRMATION OF
THE OPERATION
Specifying data to be monitored
ar
es
.co
m
/
<1> Press the four setting switches at the same time for at least a
second ."FFFFF" will be displayed on the indicator.
<2> Turn off the switches and press the "MODE" switch. "d-00" will
be displayed on the indicator and the system will enter the mode
for monitoring internal data.
In this mode, the motor can be operated normally.
<3> Press the "UP" or "DOWN" switch while holding down the
"MODE" switch. The indicator display will change in the range
of "d-00" to "d-12".
<6> Turn off the "MODE" switch. "d-xx" will disappear 0.5 second
later, and the data will be displayed for a second.
Change the set data using the "UP" or "DOWN" switch within the
second the data is displayed.
<7> When more than a second elapses without pressing the "UP" or
"DOWN" switch, data cannot be changed.
If the "MODE" switch is turned on or off, however, setting can be
started from the beginning of the step in item <6>.
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
<4> The following shows the correspondence between the
destinations of the internal data of the serial spindle and addresses
d-01 to d-12.
d-01 to d-04: Specifies the amount of data to be output to the
indicator, data shift, and output format (decimal
or hexadecimal).
d-05 to d-08: Specifies the amount of data to be output to the
LM terminal, data shift, and whether an offset is
provided.
d-09 to d-12: Specifies the amount of data to be output to the
SM terminal, data shift, and whether an offset is
provided.
<5> Select address d-xx in the procedure for setting data described in
<3>.
- 73 -
4. CONFIRMATION OF
THE OPERATION
4.3.6.5
START-UP PROCEDURE
B-65165E/02
Address descriptions and initial values (SPM)
[Output to the channel 1]
Description
Specifies a data number
d-06
Shift at data output
(0 to 31 bits)
Data shift direction
0: Data is shifted right
1: Data is shifted left
Offset
0: Not provided
1: Provided
an
uc
d-05
d-07
Initial value
A20B-2001-0830 A20B-1005-0740
(CH1)
(LM)
218
132
(U-phase current)
8
0
0
0
1
0
ef
d-08
0
-s
p
Address
Initial value
0
0
0
ar
es
.co
m
Address
Description
d-01
Specifies a data number.
d-02
Shift at data output (0 to 31 bits)
d-03
Data shift direction
0 : Data is shifted right.
1 : Data is shifted left.
d-04
Display format
0 : Decimal notation
1 : Hexadecimal notation(0 to F)
/
[Output to the indicator]
w
.g
[Output to the channel 2]
Description
d-09
Specifies a data number
d-10
Shift at data output
(0 to 31 bits)
Data shift direction
0: Data is shifted right
1: Data is shifted left
Offset
0: Not provided
1: Provided
d-11
d-12
ht
tp
://
w
w
Address
- 74 -
Initial value
A20B-2001-0830 A20B-1005-0740
(CH1)
(SM)
19
131
(Motor velocity)
18
0
0
0
1
0
START-UP PROCEDURE
B-65165E/02
4.3.6.6
4. CONFIRMATION OF
THE OPERATION
Address descriptions and initial values (SPMC)
[Output to the channel 1]
0
Initial value
A20B-2001-0830 (CH1)
54 (Spindle load level)
6
0
0
an
d-08
Specifies a data number
Shift at data output (0 to 31 bits)
Data shift direction
0: Data is shifted right
1: Data is shifted left
Offset
0: Not provided
1: Provided
uc
d-05
d-06
d-07
Description
-s
p
Address
Initial value
0
0
0
ar
es
.co
m
Address
Description
d-01
Specifies a data number.
d-02
Shift at data output (0 to 31 bits)
d-03
Data shift direction
0 : Data is shifted right.
1 : Data is shifted left.
d-04
Display format
0 : Decimal notation
1 : Hexadecimal notation(0 to F)
/
[Output to the indicator]
ef
[Output to the channel 2]
w
.g
Address
d-12
Specifies a data number
Shift at data output (0 to 31 bits)
Data shift direction
0: Data is shifted right
1: Data is shifted left
Offset
0: Not provided
1: Provided
ht
tp
://
w
w
d-09
d-10
d-11
Description
- 75 -
Initial value
A20B-2001-0830 (CH1)
34 (U-phase current)
8
0
1
4. CONFIRMATION OF
THE OPERATION
4.3.6.7
START-UP PROCEDURE
B-65165E/02
Principles in outputting the internal data of the serial spindle
ar
es
.co
m
/
The length of data is 32 bits (BIT31 TO BIT00) unless it is described as
16 bits.
……
BIT31
BIT03 BIT02 BIT01 BIT00
<1> Example of output to the indicator
Example1 Displaying data in decimal
When the number of digits to shift data (d-02)=0 and display format
(d-04)=0 (decimal notation): The last 16 bits of data (BIT15 to BIT00)
are converted into decimal (0 to 65535 max.) and displayed.
……
BIT01 BIT00
-s
p
BIT15
16 bits
Converted into decimal
data and displayed
X
X
X
X
uc
Indicator X
ef
an
Example2 Displaying data in hexadecimal
When the number of digits to shift data (d-02)=0 and display format
(d-04)=1 (hexadecimal notation): The last 16 bits of data (BIT15 to
BIT00) are converted into hexadecimal (0 to FFFFF max.) and
displayed.
ht
tp
://
w
w
w
.g
BIT15
……
BIT01 BIT00
16 bits
Converted into hexadecimal
data and displayed
Indicator
X
X
X
X (The fifth digit is blank.)
Example3 Shifting data left
When the number of digits to shift data (d-02)=3, the shift direction is
left (d-03=1), and display format (d-04)=1 (hexadecimal notation):
Data in BIT12 to BIT00 and the last three bits of data (=0) are
converted into hexadecimal (0 to FFFFF max.) and displayed.
BIT12
……
BIT01 BIT00
0
0
0
16 bits
Converted into hexadecimal
data and displayed
Indicator
X
- 76 -
X
X
X
(The fifth digit is blank.)
4. CONFIRMATION OF
THE OPERATION
START-UP PROCEDURE
B-65165E/02
……
BIT20
ar
es
.co
m
/
Example4 Shifting data right
When the number of digits to shift data (d-02)=5, shift direction is right
(d-03=0), and display format (d-04)=0 (decimal notation): Data in
BIT20 to BIT05 is converted into decimal (0 to 65535 max.) and
displayed.
BIT06 BIT05
16 bits
Converted into decimal
data and displayed
Indicator X
X
X
X
X
0
0
0
……
0 BIT15
uc
0
-s
p
Example5 Shifting data right when the data length is 16 bits
When the data length is 16 bits, data shift (d-02)=5, shift direction is
right (d-03=0), and display format is decimal notation (d-04=0): The
first five bits of data and data in BIT15 to BIT05 are converted into
decimal and displayed.
BIT05
16 bits
Converted into decimal
data and displayed
X
X
ht
tp
://
w
w
w
.g
ef
an
Indicator X
- 77 -
X
X
4. CONFIRMATION OF
THE OPERATION
START-UP PROCEDURE
B-65165E/02
Internal data in
binary (decimal)
Setting d-08
(whether there is
offset)
0
0
1
1
1
Output on channel 1
A20B-2001-0830 A20B-1005-0740
-5V
+4.96V
-5V
0V
+4.96V
-s
p
00000000( 0)
11111111( 255)
10000000(-128)
00000000( 0)
01111111( 127)
ar
es
.co
m
/
<2> Example of output to the channel 1
Internal data is output to channel 1 by setting it in an 8-bit D/A
convertor.
The output range of the D/A convertor varies from one printedcircuit board to another. The output ranges from -5 V to +5 V
(printed-circuit board A20B-2001-0830) or from 0 V to +11 V
(printed-circuit board A20B-1005-0740) according to the internal
data that is set. See the table below.
0V
+11V
0V
+5.5V
+11V
an
uc
Example1 Data set
When the number of digits to shift data (d-06)=0 and when no offset is
provided (d-08=0): The last eight bits of data (BIT07 to BIT00) is set
in the D/A converter of the LM terminal.
ef
BIT07 BIT06 BIT05 BIT04 BIT03 BIT02 BIT01 BIT00
Set in the D/A converter for channel 1 output
ht
tp
://
w
w
w
.g
Example2 Shifting data left
When the number of digits to shift data (d-06)=3, shift direction is right
(d-07=1), and no offset is provided (d-08=0): Data in BIT14 to BIT00
and the last three bits of data (=0) are set in the D/A converter.
BIT04 BIT03 BIT02 BIT01 BIT00
0
0
0
Set in the D/A converter for channel 1 output
Example3 Shifting data right
When the number of digits to shift data (d-06)=10, shift direction is
right (d-07=1), and no offset is provided (d-08=0): Data in BIT17 to
BIT10 is set in the D/A converter.
BIT17 BIT16 BIT15 BIT14 BIT13 BIT12 BIT11 BIT10
Set in the D/A converter for channel 1 output
- 78 -
4. CONFIRMATION OF
THE OPERATION
START-UP PROCEDURE
B-65165E/02
0
0
ar
es
.co
m
/
Example4 Shifting data right when the data length is 16 bits
When the data length is 16 bits, data shift (d-06)=10, shift direction is
right (d-07=0), and no offset is provided (d-08=0): The first two bits of
data (=0) and data in BIT15 to BIT10 are set in the D/A converter.
BIT15 BIT14 BIT13 BIT12 BIT11 BIT10
Set in the D/A converter for channel 1 output
Example5 If an offset is provided
When the number of digits to shift data (d-06)=10, shift direction is
right (d-07=0), and an offset is provided (d-08=1): Data in most
significant bit BIT17 (to which 1 is added) and data in BIT16 to BIT10
are set in the D/A converter.
BIT16 BIT15 BIT14 BIT13 BIT12 BIT11 BIT10
-s
p
BIT17 Data +1
Data bit observation
(for printed-circuit board A20B-2001-0830 only)
For data shift (d-06) = 0 with no offset (d-08 = 0), the lowest data bit
(BIT00) can be observed as a high/low level at check terminal CH1D.
an
Example6
uc
Set in the D/A converter for channel 1 output
Output to check terminal CH1D
<3> Example of output to the channel 2
Output to the channel 2 is the same as that to the channel 1.
However, the addresses for setting data (d-09 to d-12) are
different from those for output to the channel 1.
Setting velocity information in the channel 1 and the number of
errors in the channel 2 enables simultaneous monitoring of the
change in each data item using the two channels.
ht
tp
://
w
w
w
.g
ef
BIT07 BIT06 BIT05 BIT04 BIT03 BIT02 BIT01 BIT00
- 79 -
4. CONFIRMATION OF
THE OPERATION
4.3.6.8
START-UP PROCEDURE
B-65165E/02
Data numbers
Data
length
32
Motor speed
32
25
Motor speed deviation
32
4
Move command
32
9
Positioning error
32
Torque command
Speedometer data
Load meter data
Position error
16
16
16
32
uc
90
131
132
136
an
Data between the spindle and CNC
5 Speed command data
16
6 Spindle control signal 1
16
Load meter data
Motor speed data
Spindle status signal 1
16
16
16
Spindle control signal 2
16
ef
10
11
12
w
.g
66
tp
://
w
w
182 Spindle status signal 2
ht
The 12th bit (BIT12) indicates a units in
rpm.
The 12th bit (BIT12) indicates a units in
rpm.
(Speed command - motor speed) The
12th bit (BIT12) indicates a units in rpm.
Number of command pulses for ITP
(usually 8 ms)
Number of erroneous pulses (Spindle
synchronous control Cs contour control
Rigid mode)
0 to ±16384
SM terminal
LM terminal
Number of erroneous pulses (Position
coder orientation)
-s
p
19
Remarks
ar
es
.co
m
Data
Description
No.
Main data
16 Motor speed command
/
(1) SPM
Other data
218 Phase U current (A/D
conversion data)
219 Phase V current (A/D
conversion data)
121 Magnetic sensor signal
(MS signal on the main
side)
125 Magnetic sensor signal
(MS signal on the sub
side)
162 DC link voltage
16
16
±16384 for the maximum speed command
See the command signal from the PMC to
spindle in (4).
±16384 for maximum output
±16384 for maximum speed
See the status signal from the spindle to
PMC in (4).
See the command signal from the PMC to
spindle in (4).
See the status signal from the spindle to
PMC in (4).
10 V/FS by shifting 8 bits left(Note)
16
16
15.4 V/FS by shifting 8 bits left(Note)
16
16
1000 V/FS by shifting 8 bits left(Note)
NOTE
Printed-circuit board A20B-2001-0830 has no check
pin for IU, IV, VDC, MSA1 or MSA2. To observe
signals such as phase U current, output the
corresponding internal data to channels 1 and 2.
Shift the data to be observed by 8 bits left with an
offset. The table (3) lists the internal data
conversion.
- 80 -
4. CONFIRMATION OF
THE OPERATION
START-UP PROCEDURE
B-65165E/02
(2) SPMC
Data
length
Motor speed
32
13
Estimated motor speed
32
18
Spindle speed
32
7
Motor speed deviation
32
4
Move command
32
9
Position error
32
16
16
32
uc
90 Torque command
131 Load meter data
117 Position error
an
Data between the spindle and CNC
74 Speed command data
16
77 Spindle control signal 1
16
Load meter data
Motor speed data
Spindle status signal 1
ht
tp
://
w
w
w
.g
ef
54
55
61
The 12th bit (bit 12) indicates the unit of
-1
min .
The 12th bit (bit 12) indicates the unit of
-1
min (only when a position coder is used)
The 12th bit (bit 12) indicates the unit of
-1
min .
The 12th bit (bit 12) indicates the unit of
-1
min (only when a position coder is used)
(Speed command - motor speed). The
-1
12th bit (bit 12) indicates the unit of min .
Number of command pulses for ITP
(usually 8 ms)
Number of erroneous pulses (spindle
synchronization, Cs contour control, rigid
mode)
0 to ±16384
LM pin
Number of erroneous pulses (position
coder orientation)
-s
p
8
/
32
Remarks
ar
es
.co
m
Data
Description
No.
Main data
19 Motor speed command
16
16
16
78
Spindle control signal 2
16
62
Spindle status signal 2
16
Other data
34 Phase U current (A/D
conversion data)
35 Phase V current (A/D
conversion data)
39 DC link voltage
16
±16384 for the maximum speed command
See the command signal from the PMC to
spindle in (4).
±16384 for maximum output
±16384 for maximum speed
See the status signal from the spindle to
PMC in (4).
See the command signal from the PMC to
spindle in (4).
See the status signal from the spindle to
PMC in (4).
10 V/FS by shifting 8 bits left(Note)
16
16
1000 V/FS by shifting 8 bits left(Note)
NOTE
Internal data conversion is performed as shown in
the Table in (3).
- 81 -
4. CONFIRMATION OF
THE OPERATION
START-UP PROCEDURE
B-65165E/02
(3) Internal data conversion (A20B-2001-0830)
162
121
VDC
MSA1
125
MSA2
/
IV
ar
es
.co
m
219
Description (All are voltage values on check pins when
the shift amount is 8.)
Phase U current The current is positive when it is input to the
amplifier.
Phase V current
Model
Conversion result
SPM-2.2, 5.5
16.7 A/1 V
SPM-11HV
SPM-11, 15HV
33.3 A/1 V
SPM-15, 25HV
50.0 A/1 V
SPM-22, 45HV
66.7 A/1 V
SPM-26
100 A/1 V
SPM-30, 75HV
133 A/1 V
SPM-45
200 A/1 V
SPM-55
233 A/1 V
DC link voltage signal 100 V/1 V (200 V/1 V for SPM-HV)
Magnetic sensor output MSA signal 1 1.54 V/1 V
(Adjustment value on check board: Single amplitude 2.0 V
min, offset ±300 mV max)
Magnetic sensor output MSA signal 2 1.54 V/1 V
-s
p
Signal
name
IU
uc
Data
No.
218
(4) Spindle control signals (PMC signals)
an
Data
No.
6
BIT15
BIT14
BIT13
BIT12
BIT11
BIT10
BIT09
RCH
RSL
INTG
SOCN
MCFN
SPSL
*ESP
ARST
BIT07
BIT06
BIT05
BIT04
BIT03
BIT02
BIT01
BIT00
MRDY
ORCM
SFR
SRV
CTH1
CTH2
TLMH
TLML
Spindle control signal 1 (command signal from the PMC to spindle)
ef
w
.g
12
ht
tp
://
w
w
66
182
Description
BIT08
Spindle control signal 2 (control signal from the PMC to spindle)
BIT15
BIT14
BIT13
BIT12
BIT11
BIT10
BIT09
BIT08
*DOPN
DSCN
SORSL
MPOF
SLV
MORCM
BIT07
BIT06
BIT05
BIT04
BIT03
BIT02
BIT01
BIT00
RCHHG
MFNHG
INCMD
OVR
DEFMD
NRRO
ROTA
INDX
Spindle status signal 1 (status signal from the spindle to PMC)
BIT15
BIT14
BIT13
BIT12
BIT11
BIT10
BIT09
MOAR2
MOAR1
POAR2
SLVS
RCFN
RCHP
CFIN
BIT08
CHP
BIT07
BIT06
BIT05
BIT04
BIT03
BIT02
BIT01
BIT00
ORAR
TLM
LDT2
LDT1
SAR
SDT
SST
ALM
Spindle status signal 2 (status signal from the spindle to PMC)
BIT15
BIT14
BIT13
BIT07
BIT06
BIT05
- 82 -
BIT12
BIT11
BIT10
BIT09
BIT08
BIT04
BIT03
BIT02
BIT01
BIT00
EXOF
SOREN
MSOVR
INCST
PC1DT
START-UP PROCEDURE
B-65165E/02
4.3.6.9
4. CONFIRMATION OF
THE OPERATION
Example of monitoring data
Set Data
9
9
9
0
1
1
0
0
1
1
1
1
256p/FS 512p/FS 128p/FS
ar
es
.co
m
Address
Description
d-05
Data number
d-06
Data shift
d-07
Data shift direction
d-08
Offset
Data unit (NOTE)
/
<1> Example of monitoring a positioning error using the channel 1
9
2
1
1
64p/FS
-s
p
NOTE
Printed-circuit board A20B-2001-0830:
FS=10V (-5V to 5V)
Printed-circuit board A20B-1005-0740:
FS=11V (0V to 11V)
<2> Example of monitoring a motor speed using the channel 2
Set Data
19
19
12
13
0
0
0
0
-1
-1
256min /FS 512min /FS
an
uc
Address
Description
d-09
Data number
d-10
Data shift
d-11
Data shift direction
d-12
Offset
Data unit (NOTE)
19
11
0
0
128p/FS
<3> Observation of phase U current in the SPM-11
Setting of observation data
+5 V
Data No.
218
Shift amount
8
Shift direction
0 (shifted left)
Offset
1 (provided)
100 A
0V
33.3 A/1 V
tp
://
w
w
w
.g
ef
NOTE
Printed-circuit board A20B-2001-0830:
FS=10V (-5V to 5V)
Printed-circuit board A20B-1005-0740:
FS=11V (0V to 11V)
ht
-5 V
- 83 -
B-65165E/02
ar
es
.co
m
PERIODIC MAINTENANCE OF SERVO
AMPLIFIER
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
5
START-UP PROCEDURE
/
5. PERIODIC MAINTENANCE
OF SERVO AMPLIFIER
- 84 -
START-UP PROCEDURE
B-65165E/02
5.1
5. PERIODIC MAINTENANCE
OF SERVO AMPLIFIER
BATTERY FOR THE ABSOLUTE PULSE CODER
ar
es
.co
m
/
When the interface with the CNC is type B or FSSB, the battery for the
absolute pulse coder is required for absolute-position detection.
The battery for the absolute pulse coder is installed in the following
two methods:
-s
p
Method 1: Installing a special lithium battery in the SVM
• Use A06B-6073-K001.
Method 2: Using a battery case (A06B-6050-K060)
• Use A06B-6050-K061 or a commercially available
size-D battery.
• A connection cable (A06B-6093-K810) is required.
Use
Battery
Battery
Battery case
Cable for battery
connection
Connector for battery
connection
ht
tp
://
w
w
w
.g
ef
an
uc
Method 1
Method 2
Name
- 85 -
Order specification
drawing No.
A06B-6073-K001
A06B-6050-K061
A06B-6050-K060
A06B-6093-K810
A06B-6093-K303
Classification
Option
5. PERIODIC MAINTENANCE
OF SERVO AMPLIFIER
5.1.1
START-UP PROCEDURE
B-65165E/02
Installing a Special Lithium Battery in the SVM (Method 1)
ar
es
.co
m
/
A special lithium battery (A06B-6073-K001) can be installed in the
SVM (see the figure below).
[Installation procedure]
(1) Remove the battery cover from the SVM.
(2) Install the battery in the SVM as shown in the figure below.
(3) Install the battery cover.
(4) Attach the battery connector to CX5X or CX5Y of the SVM.
SVM
Inserting direction
Cable side
Connector
Black: 0 V
Battery
Battery cover
an
CX5X, CX5Y
uc
-s
p
Red: +6 V
+6 V
ef
0V
ht
tp
://
w
w
w
.g
WARNING
1 Install the battery with correct polarity. If the battery
is installed with incorrect polarity, it may overheat,
blow out, or catch fire.
2 When installing the battery with its connector
attached to connector CX5X or CX5Y, attach the
factory-installed protection socket to the unused
connector. When the +6-V and 0-V pins of CX5X or
CX5Y are short-circuited, the battery may overheat,
blow out, or catch fire.
CAUTION
1 You may attach the battery connector to either CX5X
or CX5Y.
2 When the battery is installed in the SVM from the
side from which the cable is drawn, the cable may be
stretched tight, which can lead to a poor contact
condition. Therefore, install the battery so that the
cable is not extended tightly.
- 86 -
START-UP PROCEDURE
B-65165E/02
5.1.2
5. PERIODIC MAINTENANCE
OF SERVO AMPLIFIER
Using a Battery Case (A06B-6050-K060) (Method 2)
Battery unit
ar
es
.co
m
/
Details of connection of the battery unit to the SVM
SVM
+6 V
CX5X, CX5Y (2)
0V
CX5X, CX5Y (1)
2
0.3 mm × 2
Housing
: 1L-L2S-S3L-B(N)
Contact
: 1L-C2-1-00001
Manufacturer: Japan Aviation Electronics
Industry, Ltd.
-s
p
Screw terminal: M3
Crimp terminal: 1.25-4
uc
Note) A special crimping tool is required to attach the contacts to a
cable. Contact the following:
Japan Aviation Electronics Industry, Ltd.
CAUTION
1 You may attach the battery connector to either CX5X
or CX5Y.
2 To an unused connector, attach the supplied
protection socket.
ht
tp
://
w
w
w
.g
ef
an
WARNING
1 Install the battery with correct polarity. If the battery
is installed with incorrect polarity, it may overheat,
blow out, or catch fire.
2 When installing the battery with its connector
attached to connector CX5X or CX5Y, attach the
factory-installed protection socket to the unused
connector. When the +6-V and 0-V pins of CX5X or
CX5Y are short-circuited, the battery may overheat,
blow out, or catch fire.
- 87 -
5. PERIODIC MAINTENANCE
OF SERVO AMPLIFIER
5.1.3
START-UP PROCEDURE
B-65165E/02
Connecting a Battery to Multiple SVMs
ar
es
.co
m
(1) Connecting a battery installed in one SVM to other SVMs
/
There are two methods for connecting a battery to more than one SVM.
(2) Connecting a separate battery unit to SVMs
The following connector kit is provided for preparing cables:
Drawing No.
A06B-6093-K303
Part number of
manufacturer
Japan Aviation
1L-L2S-S3L-B(N)
Electronics Industry, Ltd. 1L-C2-1-00001
Manufacturer
Product Quantity
Housing
Contact
2
4
an
uc
Inserting direction
-s
p
Note) A special crimping tool is required to attach contacts to a cable.
Contact the following:
Japan Aviation Electronics Industry, Ltd.
0V
Cable side
ef
1L-L2S-S3L-B(N)
+6 V
ht
tp
://
w
w
w
.g
WARNING
1 Install the battery with correct polarity. If the battery
is installed with incorrect polarity, it may overheat,
blow out, or catch fire.
2 When installing the battery with its connector
attached to connector CX5X or CX5Y, attach the
factory-installed protection socket to the unused
connector. When the +6-V and 0-V pins of CX5X or
CX5Y are short-circuited, the battery may overheat,
blow out, or catch fire.
CAUTION
Note that when a battery is shared among more than
one servo amplifier module (SVM), the battery life
will shorten. The following table shows general life
times of batteries.
Battery type
Lithium battery
Alkaline size D battery
- 88 -
General life time
One year for three axes
One year for six axes
START-UP PROCEDURE
B-65165E/02
5. PERIODIC MAINTENANCE
OF SERVO AMPLIFIER
(1) Connecting a battery installed in one SVM to other SVMs
SVM
CX5X
CX5Y
No battery
uc
Battery contained
CX5X
-s
p
CX5Y
ar
es
.co
m
/
SVM
(2) Connecting a separate battery unit to SVMs
SVM
w
.g
ef
an
SVM
://
w
w
Battery unit
A06B-6050-K060
CX5X
CX5Y
CX5Y
No battery
No battery
Cable between the battery and amplifier
A06B-6093-K810 (Only a 5-m cable is available.)
ht
tp
Battery contained
CX5X
- 89 -
5. PERIODIC MAINTENANCE
OF SERVO AMPLIFIER
START-UP PROCEDURE
B-65165E/02
Details of connection between SVMs
CX5X, CX5Y (2)
CX5X, CX5Y (1)
ar
es
.co
m
CX5X, CX5Y (2)
/
SVM
SVM
CX5X, CX5Y (1)
2
0.3 mm × 2
Housing
: 1L-L2S-S3L-B(N)
Contact
: 1L-C2-1-00001
Manufacturer: Japan Aviation
Electronics Industry, Ltd.
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
Housing
: 1L-L2S-S3L-B(N)
Contact
: 1L-C2-1-00001
Manufacturer: Japan Aviation
Electronics Industry, Ltd.
- 90 -
START-UP PROCEDURE
B-65165E/02
5.1.4
5. PERIODIC MAINTENANCE
OF SERVO AMPLIFIER
Replacing the Battery
ar
es
.co
m
/
To prevent absolute-position information of the absolute pulse coder
from being lost, replace the battery while the power for control is on.
Follow the procedure explained below.
Make sure that the power to the SVM is on (the 7-segment LED
on the front of the SVM is on).
2.
Make sure that the emergency stop button of the system has been
pressed.
3.
Make sure that the motor is not activated.
4.
Make sure that the DC link charge LED of the SVM is off.
5.
Remove the old battery, and install a new battery.
6.
This completes the replacement. You can turn off the power to
the system.
uc
-s
p
1.
ht
tp
://
w
w
w
.g
ef
an
WARNING
1 When replacing the battery, be careful not to touch
bare metal parts in the panel. In particular, be
careful not to touch any high-voltage circuits due to
the electric shock hazard.
2 Before replacing the battery, check that the DC link
charge confirmation LED on the front of the servo
amplifier is off. Neglecting this check creates an
electric shock hazard.
3 Install the battery with correct polarity. If the battery
is installed with incorrect polarity, it may overheat,
blow out, or catch fire.
4 When installing the battery with its connector
attached to connector CX5X or CX5Y, attach the
factory-installed protection socket to the unused
connector. When the +6-V and 0-V pins of CX5X or
CX5Y are short-circuited, the battery may overheat,
blow out, or catch fire.
- 91 -
5. PERIODIC MAINTENANCE
OF SERVO AMPLIFIER
5.1.5
START-UP PROCEDURE
B-65165E/02
Attaching and Detaching Connectors
<1>
ar
es
.co
m
/
(1) Attaching connectors
Check the attachment
position.
<2>
Plug the cable
connector while raising
it slightly.
-s
p
10 degrees or less
uc
<5>
Here, the angle of the
cable connector to the
horizontal must be 5
degrees or less.
w
.g
ef
<3>
an
5 degrees or less
ht
tp
://
w
w
<4>
After passing the lock
pin, insert the
connector straight.
The attachment of the
connector is
completed.
CAUTION
When attaching or detaching the battery connector,
be careful not to apply excessive torsion to the
connector. When the connector is attached or
detached, applying excessive stress to the connector
can lead to a poor contact condition or other
problems.
- 92 -
START-UP PROCEDURE
B-65165E/02
5. PERIODIC MAINTENANCE
OF SERVO AMPLIFIER
(2) Detaching the connector
Hold both the sides of
the cable insulator and
the cable, and pull them
horizontally.
ar
es
.co
m
/
<1>
-s
p
<2>
Pull out the cable side
while raising it slightly.
uc
10 degrees or less
an
<3>
ht
tp
://
w
w
w
.g
ef
5 degrees or less
- 93 -
Here, the angle of the
cable to the horizontal
must be 5 degrees or
less.
://
tp
ht
w
w
w
.g
ar
es
.co
m
-s
p
uc
an
ef
II. TROUBLESHOOTING
/
/
OVERVIEW
ar
es
.co
m
1
1.OVERVIEW
TROUBLESHOOTING
B-65165E/02
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
This part describes the troubleshooting procedure for each module.
Read the section related to your current trouble to locate it and take an
appropriate action.
First, check the alarm number and STATUS display indicated on your
module with each list (alarm numbers in the list are those for the CNC)
in Chapter 2 to find the corresponding detailed information in Chapter
3. Then take an appropriate action according to the detailed
information.
- 97 -
B-65165E/02
ar
es
.co
m
ALARM NUMBERS AND BRIEF
DESCRIPTIONS
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
2
TROUBLESHOOTING
/
2. ALARM NUMBERS AND
BRIEF DESCRIPTIONS
- 98 -
TROUBLESHOOTING
B-65165E/02
2.1
2. ALARM NUMBERS AND
BRIEF DESCRIPTIONS
FOR SERIES 16i, 18i, 20i, 21i, AND Power Mate i
Description
-s
p
Pulse coder checksum error (built-in)
Pulse coder phase error (built-in)
Clock error (built-in)
Soft phase alarm (built-in)
LED error (built-in)
Pulse error (built-in)
Count error (built-in)
Serial data error (built-in)
Data transfer error (built-in)
LED error (separate)
Pulse coder phase error (separate)
Count error (separate)
Pulse error (separate)
Soft phase alarm (separate)
Serial data error (separate)
Data transfer error (separate)
Invalid parameter
Excessive semi-full error
Servomotor overheat
Converter: main circuit overload
Converter: control undervoltage/open
phase
Converter: DC link undervoltage
Inverter: control power supply
undervoltage
Inverter: DC link undervoltage
Soft thermal (OVC)
Converter: input circuit overcurrent
Inverter: current alarm (L axis)
(M axis)
(N axis)
(L and M axes)
(M and N axes)
(L and N axes)
(L, M, and N axes)
Converter: DC link overvoltage
Converter excessive deceleration power
uc
ef
435
436
437
438
03
06
04
2
5
01
8
9
A
b
C
d
E
439
440
07
08
ht
tp
://
w
w
w
.g
433
434
ar
es
.co
m
SVM SPM PSM
an
Alarm
No.
360
361
363
364
365
366
367
368
369
380
381
382
383
384
385
386
417
421
430
431
432
/
Servo alarm
- 99 -
Remarks
3.3.7 (1)
3.3.7 (1)
3.3.7 (1)
3.3.7 (1)
3.3.7 (1)
3.3.7 (1)
3.3.7 (1)
3.3.7 (3)
3.3.7 (3)
3.3.7 (2)
3.3.7 (2)
3.3.7 (2)
3.3.7 (2)
3.3.7 (2)
3.3.7 (3)
3.3.7 (3)
3.3.6
3.3.8
3.3.5
3.1
3.1
3.1
3.2
3.2
3.3.3
3.1
3.2
3.1
3.1
TROUBLESHOOTING
447
448
449
Description
Current offset error
05 Converter: DC link charging/inverter DB
02 Converter: cooling fan stopped
Inverter: internal cooling fan stopped
Soft disconnection alarm
Hard disconnection alarm
Remarks
3.3.8
3.1
3.1
3.2
3.3.4
Not
issued
3.3.4
3.3.8
3.2
/
SVM SPM PSM
ar
es
.co
m
Alarm
No.
441
442
443
444
445
446
B-65165E/02
1
Hard disconnection alarm (separate)
Feedback mismatch alarm
Inverter: IPM alarm
(L axis)
(M axis)
(N axis)
(L and M axes)
(M and N axes)
(L and N axes)
(L, M, and N axes)
Soft disconnection alarm (α pulse coder) 3.3.4
8.
9.
A.
b.
C.
d.
E.
-s
p
2. ALARM NUMBERS AND
BRIEF DESCRIPTIONS
453
SVM SPM PSM
an
Alarm
No.
749
749
749
749
749
749
7n01
7n02
7n03
7n04
uc
Spindle alarm (n represents a spindle number. Example: n = 1 for the
first spindle)
ht
tp
://
w
w
w
.g
ef
A
A0
A1
A2
A3
A4
01
02
03
04
7n07
7n09
7n11
7n12
750
7n15
750
750
07
09
11
12
13
15
16
19
750
20
- 100 -
Description
Program ROM error
Program ROM error
Program RAM error
Program RAM error
SPM control circuit clock error
SRAM parity error
Motor overheat
Excessive speed deviation
DC link fuse blown
06 Input power supply open phase and power
supply failure
Excessive speed
Main circuit overload
07 DC link overvoltage
DC link overcurrent/IPM alarm
CPU internal data memory error
Output switching/spindle switching alarm
RAM error
Excessive offset of the phase U current
detection circuit
Excessive offset of the phase V current
detection circuit
Remarks
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
TROUBLESHOOTING
B-65165E/02
2. ALARM NUMBERS AND
BRIEF DESCRIPTIONS
(n represents a spindle number. Example: n = 1 for the first spindle)
24
25
26
Serial transfer data error
Setting data transfer stopped
Cs contour control speed detection signal
disconnected
Position coder signal disconnected
Cs contour control position detection
signal disconnected
Short-period overload
PSM main circuit overcurrent
Speed detection signal disconnected and
motor lock alarm
Serial communication LSI internal RAM
error
DC link precharge failure
Parameter data out of the specifiable
range
Too large of a gear ratio is specified.
Error counter overflow
Speed detector parameter error
Cs contour control one-rotation signal
detection error
Cs contour control one-rotation signal not
detected
Position coder one-rotation signal
detection error
Position coder one-rotation signal not
detected
Differential speed mode position coder
signal disconnected
A/D conversion error
Position coder one-rotation signal
detection error during thread cutting
Position coder signal error
Excessive differential speed conversion
result
Excessive speed command calculation
value during spindle synchronization
DC link undervoltage
ITP signal error I
ITP signal error II
Current overload alarm
Power line state error at spindle
switching/output switching
Control circuit cooling fan stopped
Excessive regenerated power
PSM main circuit overload
PSM cooling fan stopped
27
28
7n29
7n30
7n31
29
30
31
750
32
7n33
7n34
33
34
7n35
7n36
7n37
7n39
35
36
37
39
01
05
an
uc
7n27
7n28
40
7n41
41
ef
7n40
ht
tp
://
w
w
w
.g
7n42
42
7n43
43
7n44
7n46
44
46
7n47
7n48
47
49
7n50
50
7n51
7n52
7n53
7n54
7n55
51
52
53
54
55
7n56
7n56
7n58
7n59
56
57
58
59
- 101 -
04
08
03
02
Remarks
3.4
3.4
3.4
/
Description
ar
es
.co
m
SVM SPM PSM
-s
p
Alarm
No.
749
749
7n26
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
2. ALARM NUMBERS AND
BRIEF DESCRIPTIONS
2.2
TROUBLESHOOTING
B-65165E/02
FOR SERIES 15i
ar
es
.co
m
/
Servo alarm
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
Alarm
SVM SPM PSM
Description
No.
SV0027
Invalid digital servo parameter setting
SV0360
Pulse coder checksum error (built-in)
SV0361
Pulse coder phase error (built-in)
SV0363
Clock error (built-in)
SV0364
Soft phase alarm (built-in)
SV0365
LED error (built-in)
SV0366
Pulse error (built-in)
SV0367
Count error (built-in)
SV0368
Serial data error (built-in)
SV0369
Data transfer error (built-in)
SV0380
LED error (separate)
SV0381
Pulse coder phase error (separate)
SV0382
Count error (separate)
SV0383
Pulse error (separate)
SV0384
Soft phase alarm (separate)
SV0385
Serial data error (separate)
SV0386
Data transfer error (separate)
SV0421
Excessive semi-full error
SV0430
Servomotor overheat
SV0431
03 Converter: main circuit overload
SV0432
06 Converter: control undervoltage/open
phase
SV0433
04 Converter: DC link undervoltage
SV0434
2
Inverter: control power supply undervoltage
SV0435
5
Inverter: DC link undervoltage
SV0436
Soft thermal (OVC)
SV0437
01 Converter: input circuit overcurrent
Inverter: current alarm (L axis)
SV0438
8
(M axis)
9
(N axis)
A
(L and M axes)
b
(M and N axes)
C
(L and N axes)
d
(L, M, and N axes)
E
SV0439
07 Converter: DC link overvoltage
SV0440
08 Converter excessive deceleration power
SV0441
Current offset error
- 102 -
Remarks
3.3.6
3.3.7 (1)
3.3.7 (1)
3.3.7 (1)
3.3.7 (1)
3.3.7 (1)
3.3.7 (1)
3.3.7 (1)
3.3.7 (3)
3.3.7 (3)
3.3.7 (2)
3.3.7 (2)
3.3.7 (2)
3.3.7 (2)
3.3.7 (2)
3.3.7 (3)
3.3.7 (3)
3.3.8
3.3.5
3.1
3.1
3.1
3.2
3.2
3.3.3
3.1
3.2
3.1
3.1
3.3.8
Hard disconnection alarm (separate)
Feedback mismatch alarm
Inverter: IPM alarm
(L axis)
(M axis)
(N axis)
(L and M axes)
(M and N axes)
(L and N axes)
(L, M, and N axes)
8.
9.
A.
b.
C.
d.
E.
Spindle alarm
-s
p
SV0447
SV0448
SV0449
://
w
w
w
.g
ef
an
uc
Alarm
SVM SPM PSM
Description
No.
SP097x
A
Program ROM error
SP097x
A0
Program ROM error
SP097x
A1
Program RAM error
SP097x
A2
Program RAM error
SP097x
A3
SPM control circuit clock error
SP097x
A4
SRAM parity error
SP0001
01
Motor overheat
SP0002
02
Excessive speed deviation
SP0003
03
DC link fuse blown
SP0004
04
06 Power supply failure
SP0007
07
Excessive speed
SP0009
09
Main circuit overload
SP0011
11
07 DC link overvoltage
SP0012
12
DC link overcurrent/IPM alarm
SP098x
13
CPU internal data memory error
SP0015
15
Output switching/spindle switching alarm
SP098x
16
RAM error
19
Excessive offset of the phase U current
SP098x
detection circuit
20
Excessive offset of the phase V current
SP098x
detection circuit
SP022x
24
Serial transfer data error
SP022x
25
Serial data transfer stopped
ht
tp
Remarks
3.1
3.1
3.2
3.3.4
Not
issued
3.3.4
3.3.8
3.2
ar
es
.co
m
Alarm
SVM SPM PSM
Description
No.
SV0442
05 Converter: DC link charging/inverter DB
SV0443
02 Converter: cooling fan stopped
SV0444
1
Inverter: internal cooling fan stopped
SV0445
Soft disconnection alarm
SV0446
Hard disconnection alarm
/
TROUBLESHOOTING
B-65165E/02
2. ALARM NUMBERS AND
BRIEF DESCRIPTIONS
- 103 -
Remarks
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
TROUBLESHOOTING
B-65165E/02
Remarks
3.4
/
Alarm
SVM SPM PSM
Description
No.
SP0026
26
Cs contour control speed detection signal
error
SP0027
27
Position coder signal error
SP0028
28
Cs contour control position detection
signal error
SP0029
29
Short-period overload
SP0030
30
01 PSM main circuit overcurrent
SP0031
31
Speed detection signal disconnected and
motor lock alarm
SP098x
32
Serial communication LSI internal RAM
error
SP0033
33
05 DC link precharge failure
SP0034
34
Parameter data out of the specifiable
range
SP0035
35
Too large of a gear ratio is specified.
SP0036
36
Error counter overflow
SP0037
37
Speed detector parameter error
SP0039
39
Cs contour control one-rotation signal
detection error
SP0040
40
Cs contour control one-rotation signal not
detected
SP0041
41
Position coder one-rotation signal
detection error
SP0042
42
Position coder one-rotation signal not
detected
SP0043
43
Differential speed mode position coder
signal error
SP0044
44
A/D conversion error
SP0046
46
Position coder one-rotation signal
detection error during thread cutting
SP0047
47
Position coder signal error
SP0049
49
Excessive differential speed conversion
result
SP0050
50
Excessive speed command calculation
value during spindle synchronization
SP0051
51
04 DC link undervoltage
SP0052
52
ITP signal error I
SP0053
53
ITP signal error II
SP0054
54
Current overload alarm
SP0055
55
Power line state error at spindle
switching/output switching
SP0056
56
Control circuit cooling fan stopped
SP0056
57
08 Excessive regenerated power
SP0058
58
03 PSM main circuit overload
SP0059
59
02 PSM cooling fan stopped
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
ar
es
.co
m
2. ALARM NUMBERS AND
BRIEF DESCRIPTIONS
- 104 -
3.4
3.4
3.4
‘
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
TROUBLESHOOTING
B-65165E/02
2.3
2. ALARM NUMBERS AND
BRIEF DESCRIPTIONS
FOR SERIES 16, 18, 20, 21
Remarks
3.3.7
3.3.7
3.2
3.1
3.3.5
3.1
3.2
3.1
3.2
416
417
3.3.3
3.2
3.1
3.2
3.1
3.1
3.3.8
3.3.4
3.3.6
For the correspondence between the diagnosis screen
numbers and names, see the table below.
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
414
Diagnosis
SVM SPM PSM
Description
screen
Alarm 3
α pulse coder error alarm
Alarm 4
Pulse coder communication error alarm
Fan stopped alarm (SVM)
OVL
1
2 Fan stopped alarm (PSM)
3 Overheat alarm (PSM)
Overheat alarm (motor)
HVA
7 DC link overvoltage alarm
Abnormal current alarm (L axis)
HCA
8
(M axis)
9
(N axis)
A
(L, M axis)
b
(M, N axis)
C
(L, N axis)
d
(L, M, N axis)
E
1 (PSM overcurrent + IPM alarm)
IPM alarm
(L axis)
8.
(M axis)
9.
(N axis)
A.
(L, M axis)
b.
(M, N axis)
C.
(L, N axis)
d.
(L, M, N axis)
E.
OVC
Soft thermal (OVC)
LVA
2
Control power supply undervoltage
alarm
DC link undervoltage alarm (SVM)
5
4 DC link undervoltage alarm (PSM)
6 Power supply state alarm
FAN
1
Fan stopped alarm (Series 20 only)
2 Fan stopped alarm (Series 20 only)
MCC
5 MCC fused, precharge alarm
OFS
Current conversion error alarm
FBA
Feedback disconnected alarm
PRM
Invalid servo parameter setting alarm
ar
es
.co
m
Alarm
No.
350
351
400
/
Servo alarm
- 105 -
TROUBLESHOOTING
B-65165E/02
DGN No.
#7
#6
#5
#4
#3
#2
#1
#0
200
OVL
LVA
OVC
HCA
HVA
DCA
FBA
OFA
Alarm 2
201
ALD
Alarm 3
202
CSA
BLA
PHA
Alarm 4
203
CRC
STB
PRM
Alarm 5
204
OFS
MCC
LDM
EXP
DTE
Spindle alarm
RCA
BZA
CKA
SPH
PMS
FAN
DAL
ABF
ef
an
uc
-s
p
Alarm No. SVM SPM PSM
Description
749
A
Program ROM error
749
A0
Program ROM error
749
A1
Program RAM error
749
A2
Program RAM error
749
A3
SPM control circuit clock error
749
A4
SRAM parity error
751 (AL-01)
01
Motor overheat
751 (AL-02)
02
Excessive velocity error
751 (AL-03)
03
DC link fuse blown
751 (AL-04)
04
06 Input power supply open phase and
power supply failure
751 (AL-07)
07
Overspeed
751 (AL-09)
09
Main circuit overload
751 (AL-11)
11
07 DC link overvoltage
751 (AL-12)
12
DC link overcurrent/IPM alarm
750
13
CPU internal data memory failure
751 (AL-15)
15
Speed range switching and spindle
switching alarm
750
16
RAM error
750
19
Phase U current detector circuit
excessive offset
750
20
Phase V current detector circuit
excessive offset
749
24
Serial transfer data error
749
25
Serial data transfer stopped
751 (AL-26)
26
Cs contouring control velocity detection
signal disconnected
751 (AL-27)
27
Position coder signal disconnected
751 (AL-28)
28
Cs contouring control position detection
signal disconnected
751 (AL-29)
29
Short-period overload
751 (AL-30)
30
01 PSM main circuit overcurrent
751 (AL-31)
31
Speed detection signal disconnected
and motor lock alarm
750
32
Serial communication LSI internal RAM
error
w
.g
w
w
://
tp
ht
/
Alarm 1
ar
es
.co
m
2. ALARM NUMBERS AND
BRIEF DESCRIPTIONS
- 106 -
Remarks
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
Remarks
3.4
3.4
3.4
3.4
3.4
3.4
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
ar
es
.co
m
Alarm No. SVM SPM PSM
Description
751 (AL-33)
33
05 DC link precharge failure
751 (AL-34)
34
Parameter data out of specification
751 (AL-35)
35
Too large gear ratio specified
751 (AL-36)
36
Error counter overflow
751 (AL-37)
37
Speed detector parameter error
751 (AL-39)
39
Cs contouring control one-rotation
signal detection error
751 (AL-40)
40
Cs contouring control one-rotation
signal not detected
751 (AL-41)
41
Position coder one-rotation signal
detection error
751 (AL-42)
42
Position coder one-rotation signal not
detected
751 (AL-43)
43
Differential speed mode position coder
signal disconnected
751 (AL-44)
44
A/D conversion error
751 (AL-46)
46
Position coder one-rotation signal
detection error during thread cutting
751 (AL-47)
47
Position coder signal error
751 (AL-49)
49
Excessive differential speed conversion
result
751 (AL-50)
50
Excessive speed command computed
value during the synchronization control
of the spindle
751 (AL-51)
51
04 DC link undervoltage
751 (AL-52)
52
ITP signal error I
751 (AL-53)
53
ITP signal error II
751 (AL-54)
54
Overload current alarm
751 (AL-55)
55
Power line state error at spindle or
speed range switching
751 (AL-56)
56
Control circuit cooling fan stopped
751 (AL-57)
57
08 Excessive regenerated power
751 (AL-58)
58
03 PSM main circuit overload
751 (AL-59)
59
02 PSM cooling fan stopped
/
TROUBLESHOOTING
B-65165E/02
2. ALARM NUMBERS AND
BRIEF DESCRIPTIONS
- 107 -
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
2. ALARM NUMBERS AND
BRIEF DESCRIPTIONS
2.4
TROUBLESHOOTING
B-65165E/02
FOR SERIES 15
SVM SPM PSM
uc
an
7
5
2
5
w
.g
ef
SV006
4
6
5
1
2
3
SV027
SV110
SV114
SV115
SV116
SV117
SV124
SV129
ht
tp
://
w
w
SV015
SV023
(L axis)
(M axis)
(N axis)
(L, M axis)
(M, N axis)
(L, N axis)
(L, M, N axis)
(PSM overcurrent + IPM alarm)
IPM alarm
(L axis)
(M axis)
(N axis)
(L, M axis)
(M, N axis)
(L, N axis)
(L, M, N axis)
DC link overvoltage
Precharge alarm (Series 15-A)
(simultaneously with SV006)
Control power supply undervoltage alarm
DC link undervoltage alarm (SVM)
DC link undervoltage alarm (PSM)
Power supply state alarm
Precharge alarm (Series 15-A)
(simultaneously with SV005)
Feedback disconnected alarm
Fan stop alarm (SVM)
Fan stop alarm (PSM)
Overheat alarm (PSM)
Overheat alarm (motor)
Invalid servo parameter setting alarm
α pulse coder error alarm
Rotation speed data error alarm
Pulse coder communication error alarm
Precharge alarm (Series 15-B)
Current conversion error alarm
Excessive semi-full error alarm
Feedback mismatch alarm
Remarks
3.3.3
3.2
3.1
3.2
-s
p
1
SV004
SV005
Description
Soft thermal (OVC)
Abnormal current alarm
8
9
A
b
C
d
E
8.
9.
A.
b.
C.
d.
E.
ar
es
.co
m
Alarm
No.
SV001
SV003
/
Servo alarm
- 108 -
3.1
3.1
3.1
3.1
3.3.4
3.2
3.1
3.3.5
3.3.6
3.3.7
3.3.7
3.3.7
3.3.8
3.3.8
3.3.8
SVM SPM PSM
Description
Remarks
3.3.7
3.3.7
3.3.7(1)
3.3.7(1)
3.3.7(1)
3.3.7(1)
3.3.7(2)
3.3.7(2)
3.3.7(2)
3.3.7(2)
3.3.7(2)
3.3.7(3)
3.3.4
3.3.4
-s
p
ar
es
.co
m
Soft disconnection alarm
Hard disconnection alarm
Pulse coder error alarm (built-in)
Pulse coder error alarm (built-in)
Speed error (built-in)
Serial communication error (built-in)
Pulse coder error alarm (built-in)
Pulse coder error alarm (separate linear)
Pulse coder error alarm (separate rotary)
Speed error (separate rotary)
Separate detector alarm
Serial communication error (separate)
Hard disconnection alarm (separate)
Soft disconnection alarm (α pulse coder)
ht
tp
://
w
w
w
.g
ef
an
uc
Alarm
No.
SV323
SV324
SV325
SV326
SV327
SV330
SV331
SV333
SV334
SV335
SV338
SV339
SV340
SV351
/
TROUBLESHOOTING
B-65165E/02
2. ALARM NUMBERS AND
BRIEF DESCRIPTIONS
- 109 -
2. ALARM NUMBERS AND
BRIEF DESCRIPTIONS
TROUBLESHOOTING
B-65165E/02
Spindle alarm
16
19
07
20
24
25
26
OT327
OT328
27
28
OT329
OT330
OT331
29
30
31
OT300
32
OT333
OT334
OT335
OT336
OT399
OT399
33
34
35
36
37
39
ht
tp
://
w
w
w
.g
ef
OT300
OT300
OT326
- 110 -
01
05
Program ROM error
3.4
Program ROM error
3.4
Program RAM error
3.4
Program RAM error
3.4
SPM control circuit clock error
3.4
SRAM parity error
3.4
Motor overheat
3.4
Excessive velocity error
3.4
DC link fuse blown
3.4
Power supply failure
3.4
Overspeed
3.4
Main circuit overload
3.4
DC link overvoltage
3.4
DC link overcurrent/IPM alarm
3.4
CPU internal data memory failure
3.4
Speed range switching and spindle
3.4
switching alarm
RAM error
3.4
Phase U current detector circuit excessive 3.4
offset
Phase V current detector circuit excessive 3.4
offset
Serial transfer data error
3.4
Serial data transfer stopped
3.4
Cs contouring control velocity detection 3.4
signal disconnected
Position coder signal disconnected
3.4
Cs contouring control position detection 3.4
signal disconnected
Short-period overload
3.4
PSM main circuit overcurrent
3.4
Speed detection signal disconnected and 3.4
motor lock alarm
Serial communication LSI internal RAM 3.4
error
DC link precharge failure
3.4
Parameter data out of specification
3.4
Too large gear ratio specified
3.4
Error counter overflow
3.4
Speed detector parameter error
3.4
Cs contouring control one-rotation signal 3.4
detection error
/
Remarks
ar
es
.co
m
06
an
OT300
A
A0
A1
A2
A3
A4
01
02
03
04
07
09
11
12
13
15
Description
-s
p
OT300
OT300
SVM SPM PSM
uc
Alarm
No.
OT300
OT300
OT300
OT300
OT300
OT300
OT301
OT302
OT399
OT399
OT307
OT309
OT311
OT312
OT300
OT399
SVM SPM PSM
41
OT399
42
OT399
43
OT399
OT399
44
46
OT399
OT399
47
49
OT399
50
OT399
OT399
OT399
OT399
OT399
51
52
53
54
55
04
an
56
57
58
59
ht
tp
://
w
w
w
.g
ef
OT399
OT399
OT399
OT399
Cs contour controling one-rotation signal 3.4
not detected
Position coder one-rotation signal
3.4
detection error
Position coder one-rotation signal not
3.4
detected
Differential speed mode position coder
3.4
signal disconnected
A/D conversion error
3.4
Position coder one-rotation signal
3.4
detection error during thread cutting
Position coder signal error
3.4
Excessive differential speed conversion 3.4
result
3.4
Excessive speed command computed
value during the synchronization control of
the spindle
DC link undervoltage
3.4
ITP signal error I
3.4
ITP signal error II
3.4
Overload current alarm
3.4
Power line state error at spindle or speed 3.4
range switching
Control circuit cooling fan stopped
3.4
Excessive regenerated power
3.4
PSM main circuit overload
3.4
PSM cooling fan stopped
3.4
uc
OT399
- 111 -
Remarks
ar
es
.co
m
40
Description
-s
p
Alarm
No.
OT399
/
TROUBLESHOOTING
B-65165E/02
2. ALARM NUMBERS AND
BRIEF DESCRIPTIONS
08
03
02
2. ALARM NUMBERS AND
BRIEF DESCRIPTIONS
2.5
TROUBLESHOOTING
B-65165E/02
FOR SERIES 0-C
ar
es
.co
m
Alarm Diagnosis
SVM SPM PSM
Description
No.
screen
309
Alarm 3
α pulse coder error alarm
Alarm 4
Pulse coder communication error alarm
Fan stopped alarm (SVM)
400
OVL
1
2 Fan stopped alarm (PSM)
3 Overheat alarm (PSM)
Overheat alarm (motor)
414
HVA
7 DC link overvoltage alarm
DCA & LVA
5 Precharge alarm
Abnormal current alarm (L axis)
HCA
8
(M axis)
9
(N axis)
A
(L, M axis)
b
(M, N axis)
C
(L, N axis)
d
(L, M, N axis)
E
1 (PSM overcurrent + IPM alarm)
IPM alarm
(L axis)
8.
(M axis)
9.
(N axis)
A.
(L, M axis)
b.
(M, N axis)
C.
(L, N axis)
d.
(L, M, N axis)
E.
OVC
Soft thermal (OVC)
Control power supply undervoltage alarm
LVA
2
DC link undervoltage alarm (SVM)
5
4 DC link undervoltage alarm (PSM)
6 Power supply state alarm
416
FBA
Feedback disconnected alarm
417
PRM
Invalid servo parameter setting alarm
/
Servo alarm
Remarks
3.3.7
3.2
3.1
3.2
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
3.3.5
3.2
3.2
3.2
3.3.3
3.1
3.2
3.3.4
3.3.6
For the correspondence between the diagnosis screen
numbers and names, see the table below.
DGN No.
#7
#6
#5
#4
#3
#2
#1
#0
Alarm 1 720 to 723
OVL
LVA
OVC
HCA
HVA
DCA
FBA
OFA
Alarm 2 730 to 733
ALD
CSA
BLA
PHA
RCA
BZA
CKA
SPH
CRC
STB
PRM
Alarm 3 760 to 763
Alarm 4 770 to 773
DTE
- 112 -
EXP
TROUBLESHOOTING
B-65165E/02
2. ALARM NUMBERS AND
BRIEF DESCRIPTIONS
Spindle alarm
07
16
19
20
945
945
409
24
25
26
409
409
27
28
409
409
409
29
30
31
408
32
409
409
409
409
409
409
33
34
35
36
37
39
ht
tp
://
w
w
w
.g
ef
408
- 113 -
01
05
Program ROM error
3.4
Program ROM error
3.4
Program RAM error
3.4
Program RAM error
3.4
SPM control circuit clock error
3.4
SRAM parity error
3.4
Motor overheat
3.4
Excessive velocity error
3.4
DC link fuse blown
3.4
Input power supply open phase and power 3.4
supply failure
Overspeed
3.4
Main circuit overload
3.4
DC link overvoltage
3.4
DC link overcurrent/IPM alarm
3.4
CPU internal data memory failure
3.4
Speed range switching and spindle
3.4
switching alarm
RAM error
3.4
Phase U current detector circuit excessive 3.4
offset
Phase V current detector circuit excessive 3.4
offset
Serial transfer data error
3.4
Serial data transfer stopped
3.4
Cs contouring control velocity detection 3.4
signal disconnected
Position coder signal disconnected
3.4
Cs contouring control position detection 3.4
signal disconnected
Short-period overload
3.4
PSM main circuit overcurrent
3.4
Speed detection signal disconnected and 3.4
motor lock alarm
Serial communication LSI internal RAM 3.4
error
DC link precharge failure
3.4
Parameter data out of specification
3.4
Too large gear ratio specified
3.4
Error counter overflow
3.4
Speed detector parameter error
3.4
Cs contouring control one-rotation signal 3.4
detection error
/
Remarks
ar
es
.co
m
07
09
11
12
13
15
06
an
408
408
A
A0
A1
A2
A3
A4
01
02
03
04
Description
-s
p
409
409
409
409
408
409
SVM SPM PSM
uc
Alarm
No.
945
945
945
945
945
945
409
409
409
409
TROUBLESHOOTING
409
41
409
42
409
43
409
409
44
46
409
409
47
49
409
50
409
409
409
409
409
51
52
53
54
55
04
an
56
57
58
59
ht
tp
://
w
w
w
.g
ef
409
409
409
409
- 114 -
Remarks
Cs contouring control one-rotation signal 3.4
not detected
Position coder one-rotation signal
3.4
detection error
Position coder one-rotation signal not
3.4
detected
Differential speed mode position coder
3.4
signal disconnected
A/D conversion error
3.4
Position coder one-rotation signal
3.4
detection error during thread cutting
Position coder signal error
3.4
Excessive differential speed conversion 3.4
result
3.4
Excessive speed command computed
value during the synchronization control of
the spindle
DC link undervoltage
3.4
ITP signal error I
3.4
ITP signal error II
3.4
Overload current alarm
3.4
Power line state error at spindle or speed 3.4
range switching
Control circuit cooling fan stopped
3.4
Excessive regenerated power
3.4
PSM main circuit overload
3.4
PSM cooling fan stopped
3.4
ar
es
.co
m
40
Description
/
SVM SPM PSM
B-65165E/02
-s
p
Alarm
No.
409
uc
2. ALARM NUMBERS AND
BRIEF DESCRIPTIONS
08
03
02
ar
es
.co
m
TROUBLESHOOTING AND ACTION
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
3
/
TROUBLESHOOTING
B-65165E/02
3. TROUBLESHOOTING
AND ACTION
- 115 -
TROUBLESHOOTING
B-65165E/02
POWER SUPPLY MODULE
3.1.1
Power Supply Module (PSM, PSM-HV)
ar
es
.co
m
3.1
/
3. TROUBLESHOOTING
AND ACTION
If an alarm occurs, in the STATUS display, the ALM LED lights red,
and the two-digit 7-segment display indicates an alarm code.
status
PIL
ALM
Indicates an alarm code (01 or above).
Alarm code 01
uc
3.1.1.1
-s
p
The ALM LED lights red.
For the PSM-5.5 to PSM-11
ef
an
(1) Meaning
The main circuit power module (IPM) has detected an overload,
overcurrent, or control supply voltage decrease.
ht
tp
://
w
w
w
.g
(2) Cause and troubleshooting
(a) Cooling fan failure
Check whether the cooling fan rotates normally.
→ Replace the cooling fan.
(b) Dust buildup
→ Clean the cooling system with a vacuum cleaner or
compressed air.
(c) Overload
→ Examine the operating conditions.
(d) Input supply voltage imbalance
→ Check the input power supply specification.
(e) The specification of the AC reactor does not match the PSM
in use.
→ Check the PSM and the specification of the AC reactor.
(f) IPM failure, or control supply voltage decrease of the power
module (IPM)
→ Replace the unit or IPM.
- 116 -
TROUBLESHOOTING
B-65165E/02
3. TROUBLESHOOTING
AND ACTION
ar
es
.co
m
(1) Meaning
Overcurrent flowed into the input of the main circuit.
/
For PSM-15 to PSM-55, PSM-18HV to PSM-75HV
3.1.1.2
-s
p
(2) Cause and troubleshooting
(a) Input supply voltage imbalance
→ Check the input power supply specification.
(b) The specification of the AC reactor does not match the PSM
in use.
→ Check the PSM and the specification of the AC reactor.
(c) IGBT defective
→ Replace IGBT.
Alarm code 02
an
uc
(1) Meaning
(a) A cooling fan for the control circuit has stopped.
(b) The control supply voltage has dropped.
Alarm code 03
ht
tp
://
w
w
3.1.1.3
w
.g
ef
(2) Cause and troubleshooting
(a) Cooling fan broken
Check whether the cooling fan rotates normally.
→ Replace it.
(b) Input voltage decrease
→ Check the power supply.
(1) Meaning
The temperature of the main circuit heat sink has risen
abnormally.
(2) Cause and troubleshooting
(a) Cooling fan for the main circuit broken
Check whether the cooling fan for the main circuit rotates
normally.
→ Replace it.
(b) Dust accumulation
→ Clean the cooling system with a vacuum cleaner or the
factory air blower.
(c) Overload
→ Examine the operating conditions.
- 117 -
3. TROUBLESHOOTING
AND ACTION
B-65165E/02
Alarm code 04
ar
es
.co
m
(1) Meaning
In the main circuit, the DC voltage (DC link) has dropped.
/
3.1.1.4
TROUBLESHOOTING
3.1.1.5
-s
p
(2) Cause and troubleshooting
(a) A small power dip has occurred.
→ Check the power supply.
(b) Low input power supply voltage
→ Check the power supply specification.
(c) The main circuit power supply may have been switched off
with an emergency stop state released.
→ Check the sequence.
Alarm code 05
an
uc
(1) Meaning
(a) The input power supply is abnormal (open phase).
(b) The main circuit capacitor was not recharged within the
specified time.
w
w
w
.g
ef
(2) Cause and troubleshooting
(a) The input power supply has an open phase.
→ Check the connection.
(b) Too many SVM and/or SPM units are connected.
→ Check the specification of the PSM.
(c) The DC link is short-circuited.
→ Check the connection.
(d) The recharge current limiting resistor is defective.
→ Replace the unit.
Alarm code 06
ht
tp
://
3.1.1.6
(1) Meaning
The input power supply is abnormal (open phase).
(2) Cause and troubleshooting
(a) The input power supply has an open phase.
→ Check the connection.
- 118 -
TROUBLESHOOTING
B-65165E/02
3.1.1.7
3. TROUBLESHOOTING
AND ACTION
Alarm code 07
ar
es
.co
m
/
(1) Meaning
In the main circuit, the DC voltage at the DC link is abnormally
high.
Power Supply Module (PSMV)
ef
3.1.2
an
uc
-s
p
(2) Cause and troubleshooting
(a) Excessive regenerated power
Regeneration is impossible. The PSM does not have a
sufficient capacity.
→ Check the specification of the PSM.
(b) The output impedance of the AC power source is too high.
→ Check the power source output impedance.
(Normal if the voltage variation at maximum output time is
within 7%)
(c) Regeneration circuit failure
→ Replace the unit.
(d) The main circuit power supply may have been switched off
with an emergency stop state released.
→ Check the sequence.
w
.g
If an alarm occurs, in the STATUS display, the ALM LED lights red,
and the two-digit 7-segment display indicates an alarm code.
status
Indicates an alarm code (01 or above).
The ALM LED lights red.
ht
tp
://
w
w
PIL
ALM
- 119 -
3. TROUBLESHOOTING
AND ACTION
B-65165E/02
Alarm code 01
ar
es
.co
m
(1) Meaning
Overcurrent flowed into the DC link of the main circuit.
/
3.1.2.1
TROUBLESHOOTING
Alarm code 02
uc
3.1.2.2
-s
p
(2) Cause and troubleshooting
(a) Thyristor or IGBT failure
→ Replace the thyristor or IGBT.
(b) DC link short-circuit
→ Check the connection.
(c) The specification of the AC reactor does not match the
PSMV in use.
→ Check the PSMV and the specification of the AC
reactor.
an
(1) Meaning
A cooling fan for the control circuit has stopped.
Alarm code 03
ht
tp
://
w
w
3.1.2.3
w
.g
ef
(2) Cause and troubleshooting
(a) Cooling fan for the control circuit broken
Check whether the cooling fan for the control circuit rotates
normally.
→ Replace it.
(1) Meaning
The temperature of the main circuit heat sink has risen
abnormally.
(2) Cause and troubleshooting
(a) Cooling fan for the main circuit broken
Check whether the cooling fan for the main circuit rotates
normally.
→ Replace it.
(b) Dust accumulation
→ Clean the cooling system with a vacuum cleaner or the
factory air blower.
(c) Overload
→ Examine the operating conditions.
- 120 -
TROUBLESHOOTING
B-65165E/02
Alarm code 04
ar
es
.co
m
(1) Meaning
In the main circuit, the DC voltage (DC link) has dropped.
/
3.1.2.4
3. TROUBLESHOOTING
AND ACTION
(2) Cause and troubleshooting
(a) Low input power supply voltage
→ Check the power supply.
3.1.2.5
Alarm code 05
-s
p
(1) Meaning
The main circuit capacitor was not recharged within the specified
time.
Alarm code 06
an
3.1.2.6
uc
(2) Cause and troubleshooting
(a) Too many SVM and/or SPM units are connected.
→ Check the specification of the PSMV.
(2) Cause and troubleshooting
(a) The input supply voltage is not fed to the main circuit.
→ Check the connection.
(b) Two or more input fuses of the AC reactor unit have blown.
→ Replace the fuses.
://
w
w
w
.g
ef
(1) Meaning
(a) The main circuit supply voltage is not fed.
(b) Two or more input fuses of the AC reactor unit have blown.
Note) This alarm is also output when a momentary power failure
occurs.
ht
tp
3.1.2.7
Alarm code 16
(1) Meaning
(a) The main circuit power supply has an open phase.
(b) One input fuse of the AC reactor unit has blown.
(2) Cause and troubleshooting
(a) The main circuit power supply has an open phase.
→ Check the connection.
(b) One input fuse of the AC reactor unit has blown.
→ Replace the fuse.
- 121 -
3. TROUBLESHOOTING
AND ACTION
3.1.2.8
TROUBLESHOOTING
B-65165E/02
Alarm code 26
ar
es
.co
m
/
(1) Meaning
The frequency of the main circuit input power supply is abnormal.
(2) Cause and troubleshooting
(a) Input power supply frequency error
→ Check the input power supply specification (50/60 Hz
±1 Hz).
3.1.2.9
Alarm code 36
-s
p
(1) Meaning
The input power supply of the main circuit has an imbalance.
uc
(2) Cause and troubleshooting
(a) The input supply voltage has an imbalance of 5% or more.
→ Check the input power supply specification.
an
3.1.2.10 Alarm code 46
ef
(1) Meaning
When the magnetic contactor is turned on, the phase sequence of
the power supply cannot be determined.
w
.g
(2) Cause and troubleshooting
(a) Input power supply error
→ Check the input power supply specification.
ht
tp
://
w
w
3.1.2.11 Alarm code 07
(1) Meaning
In the main circuit, the DC voltage at the DC link is abnormally
high.
(2) Cause and troubleshooting
(a) Excessive regenerated power
The PSMV does not have a sufficient capacity.
→ Check the specification of the PSMV.
(b) The output impedance of the AC power source is too high.
→ Check the power source output impedance.
(Normal if the voltage variation at maximum output time is
within 7%)
(c) Regeneration circuit failure
→ Replace the unit.
- 122 -
TROUBLESHOOTING
B-65165E/02
3. TROUBLESHOOTING
AND ACTION
3.1.2.12 Alarm code 17
ar
es
.co
m
/
(1) Meaning
In the main circuit, the voltage at the DC link is abnormally high.
A fuse of the AC reactor unit may have blown.
(2) Cause and troubleshooting
(a) An input fuse of the AC reactor unit has blown.
→ Replace the fuse.
(b) Regeneration circuit failure
→ Replace the unit.
-s
p
3.1.2.13 Alarm code 08
uc
(1) Meaning
The offset of the current detection circuit of the main circuit DC
link is excessive.
w
.g
ef
an
(2) Cause and troubleshooting
(a) The current detection circuit of the main circuit DC link
malfunctions.
→ Replace the power printed wiring board.
(b) The control printed circuit board or A/D converter is faulty.
→ Replace the control printed circuit board.
(1) Meaning
An error occurred in internal parameter data transfer processing.
(2) Cause and troubleshooting
(a) The control printed circuit board is faulty.
→ Replace the control printed circuit board.
ht
tp
://
w
w
3.1.2.14 Alarm code 18
- 123 -
3. TROUBLESHOOTING
AND ACTION
TROUBLESHOOTING
B-65165E/02
ar
es
.co
m
(1) Meaning
(a) No ROM is installed.
(b) The ROM is faulty.
/
3.1.2.15 Alarm code A0
-s
p
(2) Cause and troubleshooting
(a) The ROM is not installed correctly, or no ROM is installed.
Check if the ROM is removed from the socket or if a bent
lead has caused a bad contact.
→ Install the ROM correctly.
(b) ROM specification error
Check the software version stamped on the ROM.
→ Install a specified ROM correctly.
(c) Control printed circuit board failure
→ Replace the control printed circuit board.
uc
3.1.2.16 Alarm code A1
an
(1) Meaning
The RAM is faulty.
w
.g
ef
(2) Cause and troubleshooting
(a) The control printed circuit board is faulty.
→ Replace the control printed circuit board.
(1) Meaning
A program is not operating normally.
(2) Cause and troubleshooting
(a) The control printed circuit board is faulty.
→ Replace the control printed circuit board.
ht
tp
://
w
w
3.1.2.17 Alarm code A2
- 124 -
TROUBLESHOOTING
B-65165E/02
3.1.3
3. TROUBLESHOOTING
AND ACTION
Power Supply Module (PSMR)
ar
es
.co
m
/
When an alarm is issued, the one-digit 7-segment LED indicates an
alarm code.
Indicates an alarm code (02 or above).
3.1.3.1
Alarm code 2
-s
p
(1) Meaning
A cooling fan for the control circuit has stopped.
Alarm code 4
ef
3.1.3.2
an
uc
(2) Cause and troubleshooting
(a) Cooling fan for the control circuit broken
Check whether the cooling fan for the control circuit rotates
normally.
→ Replace it.
(2) Cause and troubleshooting
(a) A small power dip has occurred.
→ Check the power supply.
(b) Low input power supply voltage
→ Check the power supply specification.
(c) The main circuit power supply may have been switched off
with an emergency stop state released.
→ Check the sequence.
ht
tp
://
w
w
w
.g
(1) Meaning
In the main circuit, the DC voltage (DC link) has dropped.
- 125 -
3. TROUBLESHOOTING
AND ACTION
3.1.3.3
TROUBLESHOOTING
B-65165E/02
Alarm code 5
ar
es
.co
m
/
(1) Meaning
(a) The input power supply is abnormal (open phase).
(b) The main circuit capacitor was not recharged within the
specified time.
uc
3.1.3.4
-s
p
(2) Cause and troubleshooting
(a) The input power supply has an open phase.
→ Check the connection.
(b) Too many SVM and/or SPM units are connected.
→ Check the specification of the PSM.
(c) The DC link is short-circuited.
→ Check the connection.
(d) The recharge current limiting resistor is defective.
→ Replace the unit.
Alarm code 6
an
(1) Meaning
The control supply voltage has dropped.
Alarm code 7
ht
tp
://
w
w
3.1.3.5
w
.g
ef
(2) Cause and troubleshooting
(a) Input voltage decrease
→ Check the power supply.
(1) Meaning
In the main circuit, the DC voltage at the DC link is abnormally
high.
(2) Cause and troubleshooting
(a) Excessive regenerated power
The PSMR does not have a sufficient capacity.
→ Check the specification of the PSMR.
(b) Regeneration circuit failure
→ Replace the unit.
- 126 -
TROUBLESHOOTING
B-65165E/02
Alarm code 8
ar
es
.co
m
(1) Meaning
(a) The regenerative discharge unit is heated.
(b) Regenerated power is excessive.
/
3.1.3.6
3. TROUBLESHOOTING
AND ACTION
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
(2) Cause and troubleshooting
(a) The regenerative resistance capacity is insufficient.
→ Check the specification of the regenerative resistance.
(b) Excessive regenerated power
→ Decrease the frequency of acceleration/deceleration
during operation.
(c) The cooling fan of the regenerative discharge unit is faulty.
→ Check the rotation state of the cooling fan.
- 127 -
TROUBLESHOOTING
B-65165E/02
SERVO AMPLIFIER MODULE
3.2.1
Abnormal Current Alarms (8, 9, A, b, C, d, and E in the LED
display)
ar
es
.co
m
3.2
/
3. TROUBLESHOOTING
AND ACTION
(1) Make sure that the following parameters are set to the standard
values. If they are not, abnormal current control is performed.
No. 1809
No. 2004 No. 8X04
No. 1884
No. 2006 No. 8X06
No. 1852
No. 2040 No. 8X40
No. 1853
No. 2041 No. 8X41
No. 1954(15-A),1955(15-B)
No. 2011
No. 8X10
No. 1967
No. 2074 No. 8X74
No. 1991
No. 2098 No. 8X98
uc
-s
p
(2) Remove the power line wires from the amplifier terminals, and
release an emergency stop state.
→ If an abnormal current alarm is issued, the servo amplifier
module needs to be replaced.
→ If not, go to (3).
ht
tp
://
w
w
w
.g
ef
an
(3) Check for insulation between PE and each of the removed power
wires U, V, and W. If insulation is perfect, go to (4). If not,
disconnect the power wires from the motor connector. Then
check for insulation between PE and each of the U, V, and W
terminals on the motor.
→ If there is a short-circuit between PE and U, V, or W of the
motor, replace the motor.
→ If insulation is perfect, replace the power wires.
(4) Connect the power wires. Attach the check board (A06B-6071K290) to connector JX5 to measure the waveform of the actual
current (IR and IS) in the servo amplifier module. Accelerate or
decelerate the motor, and measure the actual current (IR and IS) of
the amplifier.
→ If an abnormal current alarm occurs right after an emergency
stop state is released, go to (5).
Release an emergency stop state, and start the motor.
Check whether the waveform of the actual current (IR and IS) is a
normal sine wave.
→ If normal, go to (5).
→ If not, replace the amplifier.
(5) Check whether there is noise on the actual current (IR and IS)
waveform.
→ If there is no noise, replace the amplifier.
→ If there is noise, use a shielding wire, and ground the
shielding, or take other countermeasures as required.
- 128 -
TROUBLESHOOTING
B-65165E/02
3. TROUBLESHOOTING
AND ACTION
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
ar
es
.co
m
/
(6) If still there is noise, a probable cause is a defective command
cable or a hardware failure in the CNC.
- 129 -
3. TROUBLESHOOTING
AND ACTION
B-65165E/02
IPM Alarms (8., 9., A., b., C., d., and E in the LED display; note
these codes are displayed simultaneously with a period.)
/
3.2.2
TROUBLESHOOTING
ar
es
.co
m
(1) Wait for about 10 minutes. Then release the emergency stop state.
If an IPM alarm still occurs, go to (2).
If the cause is IPM overheat, the IPM alarm will not recur. IPM
overheat can occur if the ambient temperature is high or the motor
is overloaded. Check the operating condition.
(2) Remove the power wires from the amplifier terminals, and release
an emergency stop state.
If the IPM alarm does not recur, go to (3).
-s
p
If the IPM alarm recurs, the probable cause is the operation of the
IPM protective function (for overcurrent or power failure).
Replace the amplifier and see.
→ If the IPM does not recur, go to (3).
ef
an
uc
(3) Check for insulation between PE and each of the removed power
wires U, V, and W. If insulation is perfect, go to (4). If not,
disconnect the power wires from the motor connector. Then
check for insulation between PE and each of the U, V, and W
terminals on the motor.
→ If there is a short-circuit between PE and U, V, or W of the
motor, replace the motor.
→ If insulation is perfect, replace the power wires.
ht
tp
://
w
w
w
.g
(4) Connect the power wires. Attach the check board (A06B-6071K290) to connector JX5 to measure the waveform of the actual
current (IR and IS) in the servo amplifier module. Accelerate or
decelerate the motor, and measure the actual current (IR and IS) of
the amplifier.
If an overcurrent alarm occurs right after an emergency stop state
is released, go to (5).
Release an emergency stop state, and start the motor.
Check whether the waveform of the actual current (IR and IS) is a
normal sine wave.
→ If normal, go to (5).
→ If not, replace the amplifier.
(5) Check whether there is noise on the actual current (IR and IS)
waveform.
→ If there is no noise, replace the amplifier.
→ If there is noise, use a shielding wire, and ground the
shielding, or take other countermeasures as required.
(6) If still there is noise, a probable cause is a defective command
cable or a hardware failure in the CNC.
- 130 -
TROUBLESHOOTING
B-65165E/02
Control Power Supply Undervoltage Alarm (2 in the LED
display)
/
3.2.3
3. TROUBLESHOOTING
AND ACTION
ar
es
.co
m
(1) Check the three-phase input voltage to the amplifier.
→ If the voltage is below 0.85 times the rating, adjust it to the
rated value.
(2) Replace the servo amplifier.
3.2.4
DC Link Undervoltage Alarm (5 in the LED display)
-s
p
(1) Check the three-phase input voltage to the power supply module.
→ If the voltage is below 0.85 times the rating, adjust it to the
rated value.
Fan Stopped Alarm (1 in the LED display)
an
3.2.5
uc
(2) Replace the servo amplifier module.
ef
(1) Make sure that the fan is not clogged up.
Current Conversion Error Alarm
(1) Exchange the command cable with the cable for the axis on which
no alarm has occurred.
→ If the alarm occurs on the same axis, go to (3).
→ If the alarm occurs on the new axis, go to (2).
(2) The command cable is defective. Replace it.
ht
tp
://
w
w
3.2.6
w
.g
(2) Replace the servo amplifier module. Alternatively, replace the
cooling fan inside the servo amplifier module according to
Chapter 4.
- 131 -
3. TROUBLESHOOTING
AND ACTION
TROUBLESHOOTING
B-65165E/02
CNC
Alarmed axis
(L-axis)
ar
es
.co
m
Servo amplifier
L-axis
Normal axis
(M-axis)
M-axis
Command cable
-s
p
(4) The servo amplifier is defective.
ht
tp
://
w
w
w
.g
ef
an
uc
(5) The module for current conversion in the CNC is defective.
- 132 -
/
(3) Exchange the command cables according to the diagram here.
When switching the CNC on, do so in an emergency stop state.
→ If the alarm recurs on the same axis, go to (5).
→ If the alarm occurs on the other axis, go to (4).
TROUBLESHOOTING
B-65165E/02
3.3
3. TROUBLESHOOTING
AND ACTION
SERVO SOFTWARE
Servo Adjustment Screen
Series 0-C
Press the
PARAM
PAGE
PAGE
keys displays the servo screen.
uc
Pressing the
key several times to display the servo setting screen.
-s
p
3.3.1
ar
es
.co
m
/
If a servo alarm is issued, an alarm message is output, and details of the
alarm are also displayed on the servo adjustment screen or the
diagnosis screen. Using the alarm identification table given in this
section, determine the alarm, and take a proper action. With a CNC of
the i series, detailed alarm messages are displayed. So, from the
information in the alarm identification table, select a proper action.
an
If the servo setting screen does not appear, specify the following
parameter, then switch the CNC off and on again:
#7
#6
#5
#4
#3
#2
#1
0389
#0
SVS
w
.g
Series 15-A/B, 15i
ef
SVS (#0)=0 (to display the servo setting screen)
w
w
Press the SERVICE key several times to cause the servo setting screen to
appear. Then press the
key, and the servo adjustment screen will
appear.
SYSTEM
→ [SYSTEM] → [
] → [SV-PRM] → [SV-TUN]
If the servo setting screen does not appear, specify the following
parameter, then switch the CNC off and on again.
#7
#6
#5
#4
#3
3111
#2
#1
#0
SVS
SVS (#0)=1 (to display the servo setting screen)
ht
tp
://
Series 16, 18, 20, 21
- 133 -
3. TROUBLESHOOTING
AND ACTION
TROUBLESHOOTING
B-65165E/02
Alarm detail
information
ar
es
.co
m
/
<1>
<2>
<3>
<4>
<5>
Alarm detail
information
-s
p
Fig. 3.3.1(a) Servo adjustment screen
<1>
<7>
uc
<2>
<6>
<8>
<4>
<9>
an
<3>
ht
tp
://
w
w
w
.g
ef
<5>
Fig. 3.3.1(b) Series 15i servo alarm screen
The table below indicates the names of the alarm bits.
Table 3.3.1 List of alarm bit names
#7
#6
#5
#4
#3
#2
#1
#0
<1> Alarm 1
OVL
LVA
OVC
HCA
HVA
DCA
FBA
OFA
<2> Alarm 2
ALD
RCA
BZA
CKA
SPH
FAN
DAL
ABF
<3> Alarm 3
<4> Alarm 4
DTE
<5> Alarm 5
EXP
CSA
BLA
PHA
CRC
STB
PRM
OFS
MCC
LDM
PMS
CMA
BZA
PMA
SPH
SVE
IDW
NCE
IFE
<6> Alarm 6
SFA
<7> Alarm 7
OHA
LDA
BLA
PHA
<8> Alarm 8
DTE
CRC
STB
SPD
<9> Alarm 9
FSD
NOTE
The empty fields do not represent alarm codes.
- 134 -
TROUBLESHOOTING
B-65165E/02
3.3.2
3. TROUBLESHOOTING
AND ACTION
Diagnosis Screen
Correspondence between the servo adjustment screen and
diagnosis screen
Series 15-A, B, 15i Series 16, 18, 20, 21 PowerMate-E
No 2711
No 200
No 3014 + 20(X-1)
2710
201
3015 + 20(X-1)
2713
202
3016 + 20(X-1)
2712
203
3017 + 20(X-1)
2714
204





205


206




uc
Alarm No.
Series 0-C
<1> Alarm 1 No 720 to 723
730 to 733
<2> Alarm 2
760 to 763
<3> Alarm 3
770 to 773
<4> Alarm 4

<5> Alarm 5

<6> Alarm 6

<7> Alarm 7

<8> Alarm 8

<9> Alarm 9
-s
p
Table 3.3.2
ar
es
.co
m
/
The alarm items of the servo adjustment screen correspond to the
diagnosis screen numbers indicated in the table below.
<7>
<1>
<8>
an
<2>
<3>
ef
<4>
w
.g
<5>
ht
tp
://
w
w
Fig. 3.3.2 Series 16i diagnosis screen
- 135 -
3. TROUBLESHOOTING
AND ACTION
3.3.3
TROUBLESHOOTING
B-65165E/02
Overload Alarm (Soft Thermal, OVC)
#6
#5
OVL
LVA
OVC
(Action)
#4
#3
#2
#1
HCA
HVA
DCA
FBA
#0
ar
es
.co
m
<1> Alarm 1
#7
/
(Alarm identification method)
OFA
(1) Make sure that the motor is not vibrating.
⇒ If a motor vibrates, the current flowing in it becomes more
than necessary, resulting in an alarm.
-s
p
(2) Make sure that the power line to the motor is connected correctly.
⇒ If the connection is incorrect, an abnormal current flows in
the motor, resulting in an alarm.
an
uc
(3) Make sure that the following parameters are set correctly.
⇒ An overload alarm is issued based on the result of calculation
of these parameters. Be sure to set them to the standard values.
For details of the standard values, refer to the parameter
manual (B-65150E).
8x62
2062
1062
ef
1877
8x63
2063
1063
1893
8x65
2065
1065
ht
tp
://
w
w
w
.g
1878
Overload protection coefficient (OVC1)
Overload protection coefficient (OVC2)
Overload protection coefficient (OVCLMT)
(4) Attach the check board (A06B-6071-K290) to connector JX5 to
measure the waveform of the actual current (IR and IS) of the
servo amplifier module. Start the motor and measure the actual
current (IR and IS).
⇒ If the actual current exceeds 1.4 times the rated current, the
constant for the acceleration/deceleration duration is too
small, or the load on the machine is too heavy for the capacity
of the motor.
⇒ If the actual current exceeds 1.4 times the rated current during
normal operation, the load on the machine is too heavy for the
capacity of the motor.
- 136 -
TROUBLESHOOTING
B-65165E/02
3.3.4
3. TROUBLESHOOTING
AND ACTION
Feedback Disconnected Alarm
#6
#5
#4
<1> Alarm 1
OVL
LVA
OVC
<2> Alarm 2
ALD
#3
#2
#1
#0
ar
es
.co
m
#7
/
(Alarm identification method)
HCA
HVA
DCA
FBA
OFA
EXP
<6> Alarm 6
SFA
FBA
ALD
EXP
SFA
Alarm description
Action
1
1
1
0
Hard disconnection (separate phase A/B)
1
1
0
0
0
Soft disconnection (closed loop)
2
1
0
0
1
Soft disconnection (α pulse coder)
3
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
(Action)
Action 1: This alarm is issued when a separate phase A/B scale is
used. Check if the phase A/B detector is connected
correctly.
Action 2: This alarm is issued when the position feedback pulse
variation is small relative to the velocity feedback pulse
variation. This means that this alarm is not issued when a
semi-full is used. Check if the separate detector outputs
position feedback pulses correctly. If position feedback
pulses are output correctly, it is considered that the motor
alone is rotating in the reverse direction at the start of
machine operation because of a large backlash between the
motor position and scale position.
1808
8X03
2003
1003
TGAL (#1)
1892
8X64
2064
1064
Standard setting
#7
#6
#5
#4
#3
#2
#1
#0
TGAL
1: Uses the parameter for the soft disconnection alarm
detection level.
Soft disconnection alarm level
4: Alarm issued for a 1/8 rotation of the motor.
Increase this value.
Action 3: This alarm is issued when synchronization between the
absolute position data sent from the built-in pulse coder and
phase data is lost. Turn off the power to the CNC, then
detach the pulse coder cable then attach it again. If this
alarm is still issued, replace the pulse coder.
- 137 -
3. TROUBLESHOOTING
AND ACTION
3.3.5
TROUBLESHOOTING
B-65165E/02
Overheat Alarm
#6
#5
<1> Alarm 1
OVL
LVA
OVC
<2> Alarm 2
ALD
OVL
ALD
#4
#3
#2
#1
#0
ar
es
.co
m
#7
/
(Alarm identification method)
HCA
HVA
DCA
FBA
OFA
EXP
EXP
Alarm description
Action
1
1
0
Motor overheat
1
1
0
0
Amplifier overheat
1
Invalid Servo Parameter Setting Alarm
ef
3.3.6
an
uc
-s
p
(Action)
Action 1: If this alarm is issued after a long-time of continuous
operation, it is considered that the motor and amplifier are
overheated. Stop operation for a while, then make a check.
If this alarm is still issued after the power is off for about 10
minutes then is turned on again, the thermostat is
considered to be faulty. If this alarm is issued intermittently,
increase the time constant or increase stop time in the
program to suppress the rise in temperature.
ht
tp
://
w
w
w
.g
The invalid servo parameter setting alarm is issued when a setting out
of the specifiable range is specified, or an overflow has occurred in an
internal calculation. When an invalid parameter is detected on the
servo side, alarm 4 #4 (PRM) = 1 results.
(Alarm identification method)
<4> Alarm 4
#7
#6
#5
#4
DTE
CRC
STB
PRM
#3
#2
#1
#0
For details and action required when the invalid servo parameter setting
alarm is issued on the servo side, refer to the parameter manual (B65150E) edition 4 and up.
(Reference information)
Method of checking details of an invalid parameter detected on the
servo side
(For Series 15i)
A number is indicated in the item "Details of invalid parameter" on
the servo alarm screen (Fig. 3.3.1(b)).
(For Series 16i, 18i, 21i, and Power Mate i)
A number is indicated in No. 352 of the diagnosis screen.
- 138 -
TROUBLESHOOTING
B-65165E/02
3.3.7
3. TROUBLESHOOTING
AND ACTION
Alarms Related to Pulse Coder and Separate Serial Detector
#7
#6
#5
<1> Alarm 1
OVL
LVA
OVC
<2> Alarm 2
ALD
<3> Alarm 3
<4> Alarm 4
DTE
<5> Alarm 5
ar
es
.co
m
/
(Bits for alarm identification)
#4
#3
#2
#1
#0
HCA
HVA
DCA
FBA
OFA
RCA
BZA
CKA
SPH
PMS
FAN
DAL
ABF
CMA
BZA
PMA
SPH
SVE
IDW
NCE
IFE
EXP
CSA
BLA
CRC
STB
OFS
MCC
<6> Alarm 6
PHA
PRM
LDM
SFA
<7> Alarm 7
OHA
LDA
BLA
<8> Alarm 8
DTE
CRC
STB
FSD
-s
p
<9> Alarm 9
PHA
SPD
uc
(1) For a built-in pulse coder
An alarm is determined from the bits of alarms 1, 2, 3, and 5. The
table below indicates the meaning of each bit.
Alarm description
Action
Soft phase alarm
Clock alarm (serial A)
Zero battery voltage
Speed error (serial A)
Count error alarm (α pulse coder)
Phase alarm (serial A)
Battery voltage decrease (warning)
Checksum alarm (serial A)
Pulse error alarm (α pulse coder)
LED error alarm (α pulse coder)
2
NOTE
An alarm for which no action number is given is
considered to be caused by a pulse coder failure.
Replace the pulse coder.
ht
tp
://
w
w
w
.g
ef
an
Alarm 3
Alarm 5
1
Alarm 2
CSA BLA PHA RCA BZA CKA SPH LDM PMA FBA ALD EXP
1
1
1
1
0
0
0
1
1
1
0
1
1
1
1
1
- 139 -
1
2
2
1
3. TROUBLESHOOTING
AND ACTION
TROUBLESHOOTING
B-65165E/02
LDA
BLA
1
1
1
1
1
1
Alarm description
SPH
1 Soft phase alarm
Pulse error alarm
Zero battery voltage
Count error alarm
Phase alarm
Battery voltage decrease
(warning)
LED error alarm
Separate detector alarm
Action
2
1
2
2
1
-s
p
1
ar
es
.co
m
OHA
Alarm 7
PHA CMA BZA PMA
/
(2) For a separate serial detector
An alarm is determined from the bits of alarm 7. The table below
indicates the meaning of each bit.
uc
NOTE
An alarm for which no action number is given is
considered to be caused by a detector failure.
Replace the detector.
Action 2: Alarms that may be issued for noise
If an alarm is issued intermittently or after emergency stop
cancellation, noise is probably the cause. So, provide noise
protection. If the same alarm is still issued after noise
protection is provided, replace the detector.
ht
tp
://
w
w
w
.g
ef
an
(Action)
Action 1: Battery-related alarms
Check if a battery is connected. When the power is turned
on for the first time after a battery is connected, the zero
battery voltage alarm is issued. In such a case, turn off the
power, then turn on the power again. If the alarm is still
issued, check the battery voltage. If the battery voltage
decrease alarm is issued, check the voltage, and replace the
battery as required.
- 140 -
TROUBLESHOOTING
B-65165E/02
3. TROUBLESHOOTING
AND ACTION
Alarm 4
CRC STB
DTE
Alarm 8
CRC STB
1
Alarm description
ar
es
.co
m
DTE
1
/
(3) Alarms related to serial communication
An alarm is determined from the bits of alarms 4 and 8.
Serial pulse coder communication alarm
1
1
1
Separate serial pulse coder communication alarm
1
Serial communication is not performed correctly. Check if
the cable is connected correctly and is not broken. If CRC
or STB is issued, noise may be the cause. So, provide noise
protection. If CRC or STB is always issued after the power
is turned on, the pulse coder or amplifier control board (i
series) or the pulse module (i series) may be faulty.
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
Action:
- 141 -
3. TROUBLESHOOTING
AND ACTION
3.3.8
TROUBLESHOOTING
B-65165E/02
Other Alarms
#7
<5> Alarm 5
OFS
DAL
#6
#5
OFS
MCC
ABF
1
1
1
ar
es
.co
m
/
(Alarm identification method)
#4
#3
#2
#1
#0
LDM
PMS
FAN
DAL
ABF
Alarm description
Action
Feedback mismatch alarm
1
Excessive semi-full error alarm
2
Current offset error alarm
3
ef
an
uc
-s
p
(Action)
Action 1: This alarm is issued when the move direction of the position
detector is opposite to the move direction of the speed
detector. Check the rotation direction of the separate
detector. If the rotation direction of the separate detector is
opposite to the rotation direction of the motor, take the
following action:
For a phase A/B detector: Reverse the connections of A and
A.
For a serial detector: Reverse the setting of the signal
direction of the separate detector.
#7
-
2018
-
#5
#4
#3
#2
#1
#0
RVRSE
w
.g
1960
#6
ht
tp
://
w
w
RVRSE (#0) Reverses the signal direction of the separate detector.
0: Does not reverse the signal direction of the separate detector.
1: Reverses the signal direction of the separate detector.
If a large distortion exists between the motor and separate detector, this
alarm may be issued in the case of abrupt acceleration/ deceleration. In
such a case, modify the detection level.
#7
1741
-
2201
-
#6
#5
#4
#3
#2
#1
RNLV
RNLV (#1) Modifies the feedback mismatch alarm detection level.
1: Detected with 1000 min-1 or more
0: Detected with 600 min-1 or more
- 142 -
#0
TROUBLESHOOTING
B-65165E/02
3. TROUBLESHOOTING
AND ACTION
1971
-
2078
-
1972
-
2079
-
ar
es
.co
m
/
Action 2: This alarm is issued when the difference between the motor
position and separate detector position exceeds the
excessive semi-full error level. Check if the conversion
efficient for dual position feedback is set correctly. If the
conversion efficient is set correctly, increase the alarm level.
If this alarm is still issued after the level is modified, check
the connection direction of the scale.
Dual position feedback conversion coefficient (numerator)
Dual position feedback conversion coefficient (denominator)
-s
p
Number of feedback pulses per motor
revolution (detection unit)
1729
-
2118
-
1,000,000
uc
Conversion coefficient =
Dual position feedback semi-full error level
an
[Setting] Detection unit. When 0 is set, no detection is made.
ht
tp
://
w
w
w
.g
ef
Action 3: The current offset value of the current detector (equivalent
to the current value in the emergency stop state) is
abnormally high. If this alarm is still issued after the power
is turned off then back on, the current detector is faulty. For
the i series, replace the control board of the amplifier. For
series other than the i series, replace the servo-related
modules on the CNC.
- 143 -
3. TROUBLESHOOTING
AND ACTION
3.4
TROUBLESHOOTING
B-65165E/02
SPINDLE AMPLIFIER MODULE
FS0
6582
FS15i
3082
ar
es
.co
m
/
This section uses the following format for describing parameter
numbers:
FS16i/16, PM-D/F
Description
4082
Setting of acceleration/deceleration
time
The items of FS15i cover FS15. For a parameter number of FS15
different from FS15i, the item is described separately.
FS18i, 20i, 21i, PMi-D, 18, 20, and 21 are covered by the items of
FS16i/16.
α Series and α (HV) Series Spindle Amplifier Module
-s
p
3.4.1
uc
If an alarm occurs in the spindle amplifier module, the ALM LED
lights red in the STATUS display, and the two-digit 7-segment LEDs
indicate the alarm code.
status
w
.g
Alarm codes A, A0 to A4, and other Ax (x for representing an
arbitrary number)
ht
tp
://
w
w
3.4.1.1
Alarm code A0, A1, 01 or above is indicated.
ef
an
The ALM LED
lights red.
A, A0
: The SPM control program is not operating.
A1, A2, Ax : An error was detected in SPM control program
processing.
A3
: An error was detected in the clock of the SPM control
printed circuit board.
A4
: A parity error was detected in the SRAM on the SPM
control printed circuit board.
(1) If an alarm is issued when the power to the PSM is turned on
(a) The ROM is not installed correctly, no ROM is installed, or
the ROM specification is incorrect
If the ROM on the SPM control printed circuit board is once
replaced, check the following:
<1> Installation direction
<2> Occurrence of a bent lead and so forth
<3> Matching of the ROM series with the unit. Check
Subsection 2.2.3 of Part I.
(b) Printed circuit board failure
Replace the SPM or SPM control printed circuit board.
- 144 -
TROUBLESHOOTING
B-65165E/02
3. TROUBLESHOOTING
AND ACTION
3.4.1.2
ar
es
.co
m
/
(2) If an alarm is issued during motor activation
(a) Influence of noise
Referring to Chapter 5, "Installation," of "FANUC SERVO
AMPLIFIER α series Descriptions (B-65162E)," check the
GND-related wiring. If the signal cable of the spindle sensor
is bundled with the power line of the servo motor, separate
them from each other.
Alarm code 01
The inside temperature of the motor is higher than the specified
temperature.
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
(1) If this alarm is issued during cutting (the motor temperature is
high)
(a) Check the cooling state of the motor.
<1> If the cooling fan of the spindle motor is stopped, check
the power supply of the cooling fan. If the cooling fan
is still inoperative, replace it with a new one.
<2> When a liquid-cooled motor is used, check the cooling
system.
<3> When the ambient temperature of the spindle motor is
higher than the specified temperature, lower the
ambient temperature to satisfy the specification.
(b) If this alarm is issued even when the load meter fluctuates in
a limited range, check the short-period rating. If the
specified value is exceeded, reduce the load.
(2) If this alarm is issued under a light load (the motor temperature is
high)
(a) When the frequency of acceleration/deceleration is too high
Set such a use condition that the average including output at
acceleration/deceleration does not exceed the continuous
rating.
(b) The parameters specific to the motor are not set correctly.
Refer to "FANUC AC SPINDLE MOTOR α series
Parameter Manual (B-65160E)."
(3) If this alarm is issued when the motor temperature is low
(a) The spindle sensor feedback cable is faulty.
Replace the cable.
(b) The SPM control printed circuit board is faulty.
Replace the SPM control printed circuit board or SPM.
(c) The motor (internal thermostat) is faulty.
Replace the motor.
- 145 -
3. TROUBLESHOOTING
AND ACTION
3.4.1.3
TROUBLESHOOTING
B-65165E/02
Alarm code 02
ar
es
.co
m
/
The actual motor speed is largely deviated from the commanded speed.
(1) If this alarm is issued during motor acceleration
(a) The parameter setting of acceleration/deceleration time is
incorrect.
In the following parameter, set the value equivalent to the
spindle inertia plus some margin:
FS0
6582
FS15i
3082
FS16i/16, PM-D/F
Description
4082
Setting of acceleration/deceleration
time
-s
p
(b) The parameter for the speed detector is not set correctly.
Referring to "FANUC AC SPINDLE MOTOR α series
Parameter Manual (B-65160E)," set a correct value.
an
uc
(2) If this alarm is issued during cutting
(a) The cutting load has exceeded the motor output power.
Check the load meter indication, and review the use
condition.
(b) The parameters for output restriction are not set correctly.
Check that the settings of the following parameters satisfy
the machine and motor specifications:
FS15i
3028
3029
w
.g
ef
FS0
6528
6529
FS16i/16, PM-D/F
Description
4028
Output restriction pattern setting
4029
Output restriction value
ht
tp
://
w
w
(c) The parameters specific to the motor are not correctly.
Refer to "FANUC AC SPINDLE MOTOR α series
Parameter Manual (B-65160E)."
- 146 -
TROUBLESHOOTING
B-65165E/02
3.4.1.4
3. TROUBLESHOOTING
AND ACTION
Alarm code 03
ar
es
.co
m
/
The fuse of the DC link has blown. (The voltage at the DC link is
insufficient.) This alarm is checked when emergency stop is cancelled.
(1) If this alarm is issued during spindle operation (rotation)
The fuse of the DC link inside the SPM has probably blown. So,
replace the SPM. This alarm may be caused by the following:
<1> Power line short-circuited to ground
<2> Motor winding short-circuited to ground
<3> IGBT or IPM module failure
Alarm code 04
w
.g
3.4.1.5
ef
an
uc
-s
p
(2) If the PSM input magnetic contactor is once turned on and is
turned off with this alarm when emergency stop is cancelled or the
CNC is started (When two spindles are connected, the magnetic
contactor may not be turned off.)
(a) The DC link wire is not connected.
Check the DC link (TB1) wiring for errors.
(b) A cable is faulty.
Pin 9 of the interface cable (JX1B-JX1A) between the PSM
and SPM may be short-circuited to 0V. Replace the cable.
(c) The fuse of the DC link inside the SPM has blown.
Replace the SPM.
ht
tp
://
w
w
It is detected that the 3-phase input to the main circuit of the PSM has
an open phase.
(1) If the PSM indicates alarm code 6
Troubleshoot according to the description of alarm code 6
provided in Section 3.1 of Part II.
(2) If the PSM indicates no alarm
(a) A cable is faulty.
The connection cable between the PSM (JX1B) and SPM
(JX1A) is faulty. Replace the cable.
(b) The SPM is faulty.
Replace the SPM or SPM control printed circuit board.
- 147 -
3. TROUBLESHOOTING
AND ACTION
3.4.1.6
TROUBLESHOOTING
B-65165E/02
Alarm code 07
ar
es
.co
m
/
The motor rotates at a speed exceeding 115% (standard setting) of the
maximum allowable speed.
(1) If this alarm is issued during spindle synchronization
If the activation (SFR, SRV) of the motor on one side is turned off
then back on in the spindle synchronization mode, the spindle
motor is accelerated to correct a position error built up during the
period, thus causing this alarm. Modify the ladder so that SFR
and SRV are not turned off in the spindle synchronization mode.
Alarm code 09
ef
3.4.1.7
an
uc
-s
p
(2) If this alarm is issued while the motor is stopped
(a) The connection cable of the spindle sensor is faulty.
Check if the cable of the spindle sensor built into the motor
(BZ sensor when a built-in motor is used) is disconnected,
and replace the cable as required.
(b) The spindle sensor built into the motor is not adjusted
correctly.
Adjust the sensor according to Subsection 4.3.4 of Part I.
ht
tp
://
w
w
w
.g
The temperature of the heat sink of the SPM main circuit has risen to
the set value. This alarm is issued for SPM-15 and up or SPM-15HV
and later. With SPM-2.2 to SPM-11 and SPM-11HV, however, alarm
code 12 is issued for the same cause.
(1) If this alarm is issued during cutting (the heat sink temperature is
high)
(a) If this alarm is issued when the load meter reads a value
below the continuous rating of the amplifier, check the
cooling state of the heat sink.
<1> If the cooling fan is stopped, check the power supply
(connector CX1A/B). If the cooling fan is still
inoperative, replace the SPM with a new one.
<2> When the ambient temperature is higher than the
specified temperature, lower the ambient temperature
to satisfy the specification.
(b) When this alarm is issued because the load meter reads a
value above the continuous rating of the amplifier, improve
the use method.
- 148 -
TROUBLESHOOTING
B-65165E/02
3. TROUBLESHOOTING
AND ACTION
ar
es
.co
m
/
(c) When the heat sink on the back of the amplifier is too dirty,
clean the heat sink, for example, by blowing air. Consider
the use of a structure that prevents the heat sink from being
directly exposed to coolant.
-s
p
(2) If this alarm is issued under a light load (the heat sink temperature
is high)
(a) When the frequency of acceleration/deceleration is too high
Set such a use condition that the average including output at
acceleration/deceleration does not exceed the continuous
rating.
(b) The parameters specific to the motor are not set correctly.
Refer to "FANUC AC SPINDLE MOTOR α series
Parameter Manual (B-65160E)."
Alarm code 11
an
3.4.1.8
uc
(3) If this alarm is issued when the heat sink temperature is low
Replace the SPM.
The PSM detected that the DC link voltage was excessively high.
(2) If the PSM indicates no alarm
(a) A cable is faulty.
The connection cable between the PSM (JX1B) and SPM
(JX1A) is faulty. Replace the cable.
(b) The SPM is faulty.
Replace the SPM or SPM control printed circuit board.
ht
tp
://
w
w
w
.g
ef
(1) If the PSM indicates alarm code 7
Troubleshoot according to the description of alarm code 7
provided in Section 3.1 of Part II.
- 149 -
3. TROUBLESHOOTING
AND ACTION
3.4.1.9
TROUBLESHOOTING
B-65165E/02
Alarm code 12
ar
es
.co
m
/
An excessively large current flowed into the DC link of the main
circuit.
With SPM-2.2 to SPM-11 and SPM-11HV, this alarm indicates that the
power module (IPM) of the main circuit detected an error such as an
excessive load, overcurrent, or low control supply voltage.
(1) If this alarm is issued on SPM-2.2 to SPM-11 and SPM-11HV
Check alarm code 09 as well.
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
(2) If this alarm is issued immediately after a spindle rotation
command is specified
(a) The motor power line is faulty.
Check for a short circuit between motor power lines and
short-circuit to ground, and replace the power line as
required.
(b) The motor winding has an insulation failure.
If the motor is short-circuited to ground, replace the motor.
(c) The parameters specific to the motor are not set correctly.
Refer to "FANUC AC SPINDLE MOTOR α series
Parameter Manual (B-65160E)."
(d) The SPM is faulty.
A power element (IGBT, IPM) may be destroyed. Replace
the SPM.
(3) If this alarm is issued during spindle rotation
(a) A power element is destroyed.
A power element (IGBT, IPM) may be destroyed. Replace
the SPM.
If the amplifier setting condition is not satisfied, or cooling is
insufficient because the heat sink is dirty, the power
elements may be destroyed.
When the heat sink on the back of the amplifier is too dirty,
clean the heat sink, for example, by blowing air. Consider
the use of a structure that prevents the heat sink from being
directly exposed to coolant.
For the setting condition, refer to "FANUC SERVO
AMPLIFIER α series Descriptions (B-65162E)."
(b) The parameters specific to the motor are not set correctly.
Referring to "FANUC AC SPINDLE MOTOR α series
Parameter Manual (B-65160E)," check the parameters
specific to the motor.
(c) Speed sensor signal error
Check the spindle sensor signal waveform according to
Subsection 4.3.4 of Part I. If an error is found, make an
adjustment or replace the detector as required.
- 150 -
TROUBLESHOOTING
B-65165E/02
3. TROUBLESHOOTING
AND ACTION
3.4.1.10 Alarm code 13
ar
es
.co
m
/
The memory inside the CPU is faulty. A check is made when the power
is turned on.
If this alarm is issued, replace the SPM or SPM control printed circuit
board.
3.4.1.11 Alarm code 15
-s
p
In output switching control or spindle switching control, the switching
operation sequence was not executed correctly.
This alarm is issued if one second or more elapses from the transition of
a switch request signal (SPSL or RSL) until a power line state check
signal (MCFN, MFNHG, RCH, or RCHHG) makes a transition.
w
w
w
.g
ef
an
uc
Troubleshooting when this alarm is issued
(a) The magnetic contactor (switch unit) for power line
switching is faulty.
If the contact is inoperative, check the power supply of the
magnetic contactor. If the magnetic contactor is still
inoperative, replace the magnetic contactor.
(b) The I/O unit or wiring for checking the contact of the
magnetic contactor is faulty.
If a defect is found in the I/O unit or wiring, replace the I/O
unit or wiring.
(c) The sequence (ladder) is incorrect.
Modify the sequence so that switching is completed within 1
second. For details of the signals, refer to Chapter 10,
"Interface Signals," in "FANUC SERVO AMPLIFIER α series
Descriptions (B-65162E)."
ht
tp
://
3.4.1.12 Alarm code 16
The memory (RAM) is faulty. A check is made when the power is
turned on.
If this alarm is issued, replace the SPM or SPM control printed circuit
board.
- 151 -
3. TROUBLESHOOTING
AND ACTION
TROUBLESHOOTING
B-65165E/02
3.4.1.13 Alarm codes 19 and 20
ar
es
.co
m
/
The offset voltage of the phase U (alarm code 19) or phase V (alarm
code 20) current detection circuit is excessively high. A check is made
when the power is turned on.
If this alarm is issued, replace the SPM. If this alarm is issued
immediately after the SPM control printed circuit board is replaced,
check the plugging of the connectors (CN1, CN3, and CN4) between
the power unit and SPM control printed circuit board.
3.4.1.14 Alarm code 24
uc
-s
p
The power to the CNC is turned off. (This symptom does not represent
an error.) Serial communication data transferred between the CNC and
spindle amplifier module contains an error.
ht
tp
://
w
w
w
.g
ef
an
Troubleshooting when this alarm is issued
(a) Noise occurring between the CNC and spindle amplifier
module (connected via an electric cable) caused an error in
communication data.
Check the condition for maximum wiring length.
Referring to Chapter 9, "Connection," in "FANUC SERVO
AMPLIFIER α series Descriptions (B-65162E)," check the
condition of electric cable connection.
(b) Noise exercises an influence because a communication cable
is bundled with the power line.
If a communication cable is bundled with the power line for
the motor, separate them from each other.
(c) A cable is faulty.
Replace the cable.
If an optical I/O link adapter is used, the optical link adapter
or optical cable may be faulty.
(d) The SPM is faulty.
Replace the SPM or SPM control printed circuit board.
(e) The CNC is faulty.
Replace the board or module related to the serial spindle.
3.4.1.15 Alarm code 25
Serial communication between the CNC and spindle amplifier module
stopped.
Troubleshoot as in the case of alarm code 24.
- 152 -
TROUBLESHOOTING
B-65165E/02
3. TROUBLESHOOTING
AND ACTION
3.4.1.16 Alarm code 26
-s
p
ar
es
.co
m
/
The sensor signal (for speed control) for Cs contour control has an
error.
<1> When a high-resolution magnetic pulse coder is used with SPM
TYPE2 (using both of the JY2 and JY5 connectors), the amplitude
of the sensor signal on the high-resolution side (1000 λ) of the
high-resolution magnetic pulse coder built into the motor on the
JY2 side is excessively small.
<2> When a built-in motor is used with SPM TYPE2 (using only the
JY5 connector), the amplitude of the sensor signal on the highresolution side (1000 to 3000 λ) of the high-resolution magnetic
pulse coder is excessively small.
<3> When SPM TYPE4 is used, the amplitude of the spindle sensor
(MZ sensor) built into the motor connected to JY2 is excessively
small.
(2) If this alarm is issued when the cable is moved (as in the case
where the spindle moves)
(a) The connector has a bad contact, or the cable is
disconnected.
The conductor may be broken. Replace the cable. If coolant
has penetrated into the connector, clean the connector.
ht
tp
://
w
w
w
.g
ef
an
uc
(1) If this alarm is issued when the motor is deactivated
(a) The setting of a parameter is incorrect.
Referring to "FANUC AC SPINDLE MOTOR α series
Parameter Manual (B-65160E)," check the parameter for
sensor setting.
(b) The sensor is not adjusted correctly, or the cable is
disconnected.
Adjust the sensor signal according to Subsection 4.3.4 of
Part I of this manual. If the signal is not observed, replace
the cable and sensor.
(c) The printed circuit board is faulty.
Replace the SPM or SPM control printed circuit board.
- 153 -
Sensor
S
P
M
The cable is
connected to
pin 10 on the
SPM side.
(3) If this alarm is issued when the motor rotates
(a) The shielding of the cable between the preamplifier or MZ
sensor (for TYPE4) and the SPM is faulty.
Referring to Chapter 9, "Connection," in "FANUC SERVO
AMPLIFIER α series Descriptions (B-65162E)," check the
shielding of the cable.
(b) The signal cable is bundled with the servo motor power line.
If the cable between the preamplifier or MZ sensor (for
TYPE4) and the SPM is bundled with the servo motor power
line, separate them from each other.
(c) Improve the cable routing between the motor and
preamplifier.
If the cables (including those within a terminal box)
extending from the motor to the preamplifier are close to the
power line, separate the cables from the power line.
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
The cable is
connected to the
pin specified in the
specifications on
the sensor side.
B-65165E/02
/
Shielded cable
TROUBLESHOOTING
ar
es
.co
m
3. TROUBLESHOOTING
AND ACTION
- 154 -
TROUBLESHOOTING
B-65165E/02
3. TROUBLESHOOTING
AND ACTION
3.4.1.17 Alarm code 27
-s
p
ar
es
.co
m
/
The sensor signal (position coder signal) for position control is
abnormal.
<1> The signal of the α position coder is disconnected (for all types).
<2> When an MZ or BZ sensor is used with SPM TYPE1 (using the
JY2 connector), the amplitude of the sensor signal is excessively
small.
<3> When a separate built-in sensor is used with SPM TYPE2 (using
the JY2 and JY5 connectors), the amplitude of the spindle sensor
signal on the JY2 side is excessively small.
<4> When a high-resolution magnetic pulse coder is used with SPM
TYPE2 (using the JY2 and JY5 connectors), the amplitude of the
sensor signal on the low-resolution side (128 to 384 λ) on the JY5
side is excessively small.
<5> When SPM TYPE4 is used, the amplitude of the spindle sensor
signal connected to JY5 is excessively small.
an
uc
(1) If this alarm is issued when the motor is deactivated
(a) The setting of a parameter is incorrect.
Referring to Chapter 2 of "FANUC AC SPINDLE MOTOR
α series Parameter Manual (B-65160E)," check the
parameter for sensor setting.
(b) The cable connected to JY4 is disconnected. (α position
coder)
When the α position coder is used, adjustment is impossible.
Replace the cable.
(c) The sensor is not adjusted correctly.
Adjust the sensor signal according to Subsection 4.3.4 of
Part I of this manual. If the sensor signal cannot be adjusted
correctly, or the sensor signal is not observed, replace the
connection cable and sensor.
(d) The SPM is faulty.
Replace the SPM or SPM control printed circuit board.
ef
α position coder
w
.g
S
P
M
w
w
Sensor
Shielded cable
ht
tp
://
Connected to the frame
ground via a cable clamp.
(2) If this alarm is issued when the cable is moved (as in the case
where the spindle moves)
(a) The connector has a bad contact, or the cable is
disconnected.
The conductor may be broken. Replace the cable. If coolant
has penetrated into the connector, clean the connector.
- 155 -
3. TROUBLESHOOTING
AND ACTION
TROUBLESHOOTING
(3) If this alarm is issued when the motor rotates
(a) The shielding of the cable between the sensor and the SPM is
faulty.
Referring to Chapter 9, "Connection," in "FANUC SERVO
AMPLIFIER α series Descriptions (B-65162E)," check the
shielding of the cable.
(b) The signal cable is bundled with the servo motor power line.
If the cable between the sensor and the SPM is bundled with
the servo motor power line, separate them from each other.
Other sensors
Shielded cable
The cable is
connected to
pin 10 on the
SPM side.
ar
es
.co
m
/
S
P
M
Sensor
The cable is
connected to the
pin specified in the
specifications on
the sensor side.
B-65165E/02
3.4.1.18 Alarm code 28
ef
an
uc
-s
p
The sensor signal (for position control) for Cs contour control is
abnormal.
<1> When a high-resolution magnetic pulse coder is used with SPM
TYPE2 (using both of the JY2 and JY5 connectors), the amplitude
of the sensor signal on the high-resolution side (1000 to 3000 λ) of
the high-resolution magnetic pulse coder on the JY5 side is
excessively small.
<2> When SPM TYPE4 is used, the amplitude of the spindle sensor
(MZ sensor) built into the motor connected to JY5 is excessively
small.
ht
tp
://
w
w
w
.g
Troubleshoot as in the case of alarm code 26.
- 156 -
TROUBLESHOOTING
B-65165E/02
3. TROUBLESHOOTING
AND ACTION
3.4.1.19 Alarm code 29
ar
es
.co
m
/
An excessive load (standard setting: load meter reading of 9 V) has
been applied continuously for a certain period (standard setting: 30
seconds).
(1) If this alarm is issued during cutting
Check the load meter, and review the cutting condition.
-s
p
(2) If this alarm is issued during a stop
(a) The spindle is locked.
Check the sequence to see if the spindle is locked when a
command for very slow movement is specified or orientation
is specified for the spindle.
(4) If the spindle does not rotate as specified (the spindle does not
rotate at all) and this alarm is issued
(a) The power line is abnormal.
Check if the motor power line is connected normally. If
spindle switching or output switching is performed, check if
the magnetic contactor is on.
(b) The SPM is faulty.
Replace the SPM.
ht
tp
://
w
w
w
.g
ef
an
uc
(3) If the spindle does not rotate as specified (the spindle rotates at a
very low speed) and this alarm is issued
(a) The setting of a parameter is incorrect.
Referring to "FANUC AC SPINDLE MOTOR α series
Parameter Manual (B-65160E)," check the parameter for
sensor setting.
(b) The phase sequence of the motor power line is incorrect.
(c) The feedback cable of the motor has a problem.
Check if the phase A/B signals are connected correctly.
(d) The feedback cable of the motor is faulty.
Rotate the motor manually to see if a speed is indicated in the
item of motor speed on the CNC diagnosis screen or on the
spindle check board. If no speed indication is provided,
replace the cable or spindle sensor (or motor).
- 157 -
3. TROUBLESHOOTING
AND ACTION
TROUBLESHOOTING
B-65165E/02
3.4.1.20 Alarm code 30
ar
es
.co
m
/
An excessively large current is detected at the input of the 3-phase main
circuit of the PSM.
(1) If the PSM indicates alarm code 1
Troubleshoot according to the description of alarm code 1
provided in Section 3.1 of Part II.
-s
p
(2) If the PSM indicates no alarm
(a) A cable is faulty.
The connection cable between the PSM (JX1B) and SPM
(JX1A) is faulty. Replace the cable.
(b) The SPM is faulty.
Replace the SPM or SPM control printed circuit board.
uc
3.4.1.21 Alarm code 31
an
The motor failed to rotate as specified, and has stopped or is rotating at
a very low speed.
ht
tp
://
w
w
w
.g
ef
(1) If the motor rotates at a very low speed and this alarm is issued
(a) The setting of a parameter is incorrect.
Referring to "FANUC AC SPINDLE MOTOR α series
Parameter Manual (B-65160E)," check the parameter for
sensor setting.
(b) The motor phase sequence is incorrect.
Check if the motor phase sequence is correct.
(c) The feedback cable of the motor has a problem.
Check if the phase A/B signals are connected correctly.
(d) The feedback cable of the motor is faulty.
Rotate the motor manually to see if a speed is indicated in the
item of motor speed on the CNC diagnosis screen or on the
spindle check board. If no speed indication is provided,
replace the cable or spindle sensor (or motor).
(2) If the motor does not rotate at all and this alarm is issued
(a) The sequence for locking the spindle is incorrect.
Check the sequence to see if the spindle is locked.
(b) The power line is faulty.
Check if the power line is connected to the motor correctly.
If spindle switching or winding switching is performed,
check if the magnetic contactor is on.
(c) The SPM is faulty.
Replace the SPM.
- 158 -
TROUBLESHOOTING
B-65165E/02
3. TROUBLESHOOTING
AND ACTION
3.4.1.22 Alarm code 32
ar
es
.co
m
/
LSI memory for serial communication is abnormal. A check is made
when the power is turned on.
If this alarm is issued, replace the SPM or SPM control printed circuit
board.
3.4.1.23 Alarm code 33
The PSM could not be charged within a specified time.
PSM input has an open phase.
uc
-s
p
(1) If the PSM indicates alarm code 5
Troubleshoot according to the description of alarm code 5
provided in Section 3.1 of Part II.
w
.g
ef
an
(2) If the PSM indicates no alarm
(a) A cable is faulty.
The connection cable between the PSM (JX1B) and SPM
(JX1A) is faulty. Replace the cable.
(b) The SPM is faulty.
Replace the SPM or SPM control printed circuit board.
3.4.1.24 Alarm code 34
Troubleshooting when this alarm is issued
Connect the spindle check board.
The spindle check board displays "AL-34" and "F-xxx"
alternately. "F-xxx" indicates a parameter number outside the
specifiable range. For the correspondence between the CNC
parameter numbers and "F-xxx," refer to "FANUC AC SPINDLE
MOTOR α series Parameter Manual (B-65160E)."
ht
tp
://
w
w
Parameter data outside the specifiable range was set.
- 159 -
3. TROUBLESHOOTING
AND ACTION
TROUBLESHOOTING
B-65165E/02
3.4.1.25 Alarm code 35
ar
es
.co
m
/
The gear ratio set in a parameter exceeds the value range allowable for
internal processing. This alarm is issued with a parameter related to
orientation of magnetic sensor type.
Troubleshooting when this alarm is issued
(a) The gear ratio set in a parameter is incorrect.
Check if an excessively large gear ratio is set.
FS16i/16, PM-D/F
Description
4056
Gear ratio between the spindle and
to
motor
4059
4060
Position gain at orientation
to
4063
uc
3.4.1.26 Alarm code 36
FS15i
3056
to
3059
3060
to
3063
-s
p
FS0
6556
to
6559
6560
to
6563
an
The error counter overflowed.
ht
tp
://
w
w
w
.g
ef
(1) The setting of a parameter is incorrect.
(a) The gear ratio set in a parameter is incorrect.
Check if an excessively large gear ratio is set.
(b) The setting of a position gain is incorrect.
If the gear ratio data is correct, increase the position gain.
(c) The setting of a position detector mounting direction or the
setting of spindle and motor rotation directions is incorrect.
FS0
6556
to
6559
6565
to
6568
6569
to
6572
FS15i
3056
to
3059
3065
to
3068
3069
to
3072
FS16i/16, PM-D/F
4056
to
4059
4065
to
4068
4069
to
4072
Description
Gear ratio between the spindle and
motor
Position gain in the servo
mode/spindle synchronization
Position gain in Cs contour control
(2) Sequence error
(a) Check if the motor is deactivated (by turning off SFR/SRV)
in a position control mode (rigid tapping, Cs contour control,
or spindle synchronization).
- 160 -
TROUBLESHOOTING
B-65165E/02
3. TROUBLESHOOTING
AND ACTION
3.4.1.27 Alarm code 37
ar
es
.co
m
/
After emergency stop signal input, the motor is accelerated without
being decelerated. This alarm is issued also when the motor is not
deactivated (the motor is not decelerated completely) when the
acceleration/deceleration time (initial parameter setting: 10 seconds)
has elapsed after emergency stop signal input.
FS16i/16, PM-D/F
Description
4082
Acceleration/deceleration time
setting
uc
FS15i
3082
ht
tp
://
w
w
w
.g
ef
an
FS0
6582
-s
p
Troubleshooting when this alarm is issued
(a) The parameter setting of the speed detector is incorrect.
Referring to Chapter 1 in "FANUC AC SPINDLE MOTOR
α series Parameter Manual (B-65160E)," set a correct time.
(b) The parameter setting of an acceleration/deceleration time is
not proper.
Check the parameter-set value and actual acceleration/
deceleration time, then set an actual acceleration/
deceleration time plus some margin.
- 161 -
3. TROUBLESHOOTING
AND ACTION
3.4.2
TROUBLESHOOTING
B-65165E/02
Alarm Code 39
FS15i
3016#5
FS16i/16, PM-D/F
Description
4016#5
Whether the function for detecting
the one-rotation signal of the
detector for Cs contour control is
provided
1: The function is provided.
-s
p
FS0
6516#5
ar
es
.co
m
/
The position where the one-rotation signal for Cs contour control is
generated is incorrect. This alarm is not issued when the parameter
indicated below is not set.
<1> When SPM TYPE2 is used, phase A/B/Z on the high-resolution
(1000 to 3000 λ) side of the high-resolution magnetic pulse coder
on the spindle side has a problem.
<2> When SPM TYPE4 is used, the spindle sensor connected to JY5 is
faulty.
Troubleshoot as in the case of alarm code 41.
w
.g
ef
an
uc
Troubleshooting when this alarm is issued (at the time of reference
position return on the Cs axis)
(a) The setting of a parameter is incorrect.
Referring to Chapter 2 in "FANUC AC SPINDLE MOTOR
α series Parameter Manual (B-65160E)," check the
parameter for sensor setting.
(b) The sensor is not adjusted correctly.
Adjust the sensor according to Subsection 4.3.4 of Part I of
this manual. If the signal is not observed, replace the sensor.
(c) The shielding of the cable between the preamplifier and
SPM is faulty.
Referring to Chapter 9, "Connection," in "FANUC SERVO
AMPLIFIER α series Descriptions (B-65162E)," check the
shielding of the cable.
(d) The signal cable is bundled with the servo motor power line.
If the cable between the preamplifier and SPM is bundled
with the servo motor power line, separate them from each
other.
(e) Improve the cable routing between the motor and
preamplifier.
If the cables (including those within a terminal box)
extending from the motor to the preamplifier are close to the
power line, separate the cables from the power line.
(f) The SPM is faulty.
Replace the SPM or SPM control printed circuit board.
w
w
Shielded cable
Sensor
S
P
M
The cable is
connected to
pin 10 on the
SPM side.
ht
tp
://
The cable is
connected to the
pin specified in the
specifications on
the sensor side.
- 162 -
TROUBLESHOOTING
B-65165E/02
3.4.2.1
3. TROUBLESHOOTING
AND ACTION
Alarm code 40
ar
es
.co
m
/
The one-rotation signal for Cs contour control is not generated.
<1> When SPM TYPE2 is used, phase A/B/Z on the high-resolution
(1000 to 3000 λ) side of the high-resolution magnetic pulse coder
on the spindle side has a problem.
<2> When SPM TYPE4 is used, the spindle sensor connected to JY5 is
faulty.
Troubleshoot as in the case of alarm code 42.
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
Troubleshooting when this alarm is issued (at the time of reference
position return on the Cs axis)
(a) The setting of a parameter is incorrect.
Referring to Chapter 2 in "FANUC AC SPINDLE MOTOR
α series Parameter Manual (B-65160E)," check the
parameter for sensor setting.
(b) The sensor is not adjusted correctly.
Adjust the sensor according to Subsection 4.3.4 of Part I of
this manual. If the signal is not observed, replace the sensor.
(c) The cable is disconnected.
Check the check pin PSD on the check board. If the signal is
not observed per sensor rotation, replace the cable.
(d) The SPM is faulty.
Replace the SPM or SPM control printed circuit board.
- 163 -
3. TROUBLESHOOTING
AND ACTION
3.4.2.2
TROUBLESHOOTING
B-65165E/02
Alarm code 41
ar
es
.co
m
/
<1> The position where the one-rotation signal of the α position coder
is generated is incorrect.
<2> The position where the one-rotation signal of the MZ sensor or BZ
sensor is generated is incorrect.
<3> The position where the one-rotation signal of α position coder S is
generated is incorrect.
(1) If orientation based on the external one-rotation method is used
(a) The settings of parameters are incorrect.
Check that the gear ratio data matches the specification of
the machine.
FS15
3315
3317
3316
3318
FS15i
3171
3173
3172
3174
uc
an
(2) Troubleshooting in other cases
(a) The setting of a parameter is incorrect.
Referring to "FANUC AC SPINDLE MOTOR α series
Parameter Manual (B-65160E)," check the parameter for
sensor setting.
(b) A sensor (MZ sensor or BZ sensor) is not adjusted correctly.
Adjust the sensor according to Subsection 4.3.4 of Part I of
this manual. If the signal is not observed, replace the sensor.
(c) The α position coder is faulty.
Check the check pin PSD on the spindle check board. If the
signal is not generated per rotation, replace the position
coder.
(d) The shielding of the cable between the sensor and SPM is
faulty.
Referring to Chapter 9, "Connection," in "FANUC SERVO
AMPLIFIER α series Descriptions (B-65162E)," check the
shielding of the cable.
(e) The signal cable is bundled with the servo motor power line.
If the cable between the sensor and SPM is bundled with the
servo motor power line, separate them from each other.
(f) The SPM is faulty.
Replace the SPM or SPM control printed circuit board.
w
.g
Sensor
S
P
M
ef
Shielded cable
w
w
Connected to the frame
ground via a cable clamp.
MZ or BZ sensor
tp
Sensor
://
Shielded cable
ht
Description
Number of teeth on the spindle
side
Number of teeth on the position
detector side
(b) Slippage between the spindle and motor
Check that there is no slippage between the spindle and
motor. Orientation based on the external one-rotation
method is not applicable to V-belt connection.
α position coder
The cable is
connected to the
pin specified in
the specifications
on the sensor
side.
FS16i/16, PM-D/F
4171
4173
4172
4174
-s
p
FS0
6935
6937
6936
6938
S
P
M
The cable is
connected to
pin 10 on the
SPM side.
- 164 -
TROUBLESHOOTING
B-65165E/02
3.4.2.3
3. TROUBLESHOOTING
AND ACTION
Alarm code 42
ar
es
.co
m
/
<1> The one-rotation signal of the α position coder is not generated.
<2> The one-rotation signal of the MZ sensor or BZ sensor is not
generated.
<3> The one-rotation signal of α position coder S is not generated.
Alarm code 43
w
.g
3.4.2.4
ef
an
uc
-s
p
Troubleshooting when this alarm is issued
(a) The setting of a parameter is incorrect.
Referring to "FANUC AC SPINDLE MOTOR α series
Parameter Manual (B-65160E)," check the parameter for
sensor setting.
(b) The MZ sensor or BZ sensor is not adjusted correctly.
Adjust the sensor according to Subsection 4.3.4 of Part I of
this manual. If the sensor cannot be adjusted or the signal is
not observed, replace the connection cable and sensor.
(c) The α position coder is faulty.
Check the check pin PSD on the spindle check board. If the
signal is not generated per rotation, replace the connection
cable and position coder.
(d) The SPM is faulty.
Replace the SPM or SPM control printed circuit board.
The position coder signal of the spindle on the mater side used in the
differential speed mode is disconnected.
w
w
Troubleshoot as in the case of alarm code 27.
Alarm code 44
ht
tp
://
3.4.2.5
3.4.2.6
An error occurred in the A/D converter.
When this alarm is issued, replace the SPM or SPM control printed
circuit board.
Alarm code 46
The one-rotation signal of the position coder cannot be detected
normally during thread cutting.
Troubleshoot as in the case of alarm code 41.
- 165 -
3. TROUBLESHOOTING
AND ACTION
3.4.2.7
TROUBLESHOOTING
B-65165E/02
Alarm code 47
ar
es
.co
m
/
<1> The count value of α position coder signal pulses is abnormal.
<2> The pulse count value of the MZ sensor or BZ sensor is abnormal.
Phases A and B for the position coder have a feedback pulse count of
4096 p/rev per spindle rotation. The SPM checks the pulse counts of
phases A and B equivalent to the position coder each time a onerotation signal is generated. The alarm is issued when a pulse count
beyond the specified range is detected.
-s
p
(1) If this alarm is issued when the cable is moved (as in the case
where the spindle moves)
(a) The connector has a bad contact, or the cable is
disconnected.
The conductor may be broken. Replace the cable. If coolant
has penetrated into the connector, clean the connector.
Shielded cable
ef
Connected to the frame
ground via a cable clamp.
MZ or BZ sensor
w
.g
S
P
M
w
w
Sensor
Shielded cable
The cable is
connected to
pin 10 on the
SPM side.
ht
tp
://
The cable is
connected to the
pin specified in
the specifications
on the sensor
side.
(2) Troubleshooting in other cases
(a) The setting of a parameter is incorrect.
Referring to "FANUC AC SPINDLE MOTOR α series
Parameter Manual (B-65160E)," check the parameter for
sensor setting.
(b) A sensor (MZ sensor or BZ sensor) is not adjusted correctly.
Adjust the sensor according to Subsection 4.3.4 of Part I of
this manual.
(c) The shielding of the cable between the sensor and SPM is
faulty.
Referring to Chapter 9, "Connection," in "FANUC SERVO
AMPLIFIER α series Descriptions (B-65162E)," check the
shielding of the cable.
(d) The signal cable is bundled with the servo motor power line.
If the cable between the sensor and SPM is bundled with the
servo motor power line, separate them from each other.
(e) The SPM is faulty.
Replace the SPM or SPM control printed circuit board.
an
Sensor
S
P
M
uc
α position coder
- 166 -
TROUBLESHOOTING
B-65165E/02
3.4.2.8
3. TROUBLESHOOTING
AND ACTION
Alarm code 49
ar
es
.co
m
/
In the differential speed mode, the spindle speed on the master side
(remote) converted to a motor speed on the slave side (local) exceeded
the maximum allowable speed of the motor.
Troubleshooting when this alarm is issued
A differential speed is calculated by multiplying the speed on the
target speed by a gear ratio.
Ensure that the maximum allowable speed of the motor is not
exceeded.
Alarm code 50
-s
p
3.4.2.9
uc
A value obtained by internal calculation in spindle synchronization
exceeded the allowable range.
ef
an
Troubleshooting when this alarm is issued
(a) The setting of parameters for gear ratio setting is incorrect.
Check if an excessively large gear ratio is set.
(b) Position gain setting limit
If correct gear ratio data is set, increase the position gain
value in spindle synchronization.
FS15i
3056
to
3059
3065
to
3068
FS16i/16, PM-D/F
4056
to
4059
4065
to
4068
Description
Gear ratio between the spindle and
motor
Position gain in the servo
mode/spindle synchronization
w
w
w
.g
FS0
6556
to
6559
6565
to
6568
ht
tp
://
3.4.2.10 Alarm code 51
The PSM detected that the DC link voltage was excessively low.
(1) If the PSM indicates alarm code 4
Troubleshoot according to the description of alarm code 4
provided in Section 3.1 of Part II.
(2) If the PSM indicates no alarm
(a) A cable is faulty.
The connection cable between the PSM (JX1B) and SPM
(JX1A) is faulty. Replace the cable.
(b) The SPM is faulty.
Replace the SPM or SPM control printed circuit board.
- 167 -
3. TROUBLESHOOTING
AND ACTION
TROUBLESHOOTING
B-65165E/02
3.4.2.11 Alarm codes 52 and 53
ar
es
.co
m
/
The synchronization signal (ITP) in communication data transferred to
and from the CNC stopped.
Troubleshooting when this alarm is issued
(a) The SPM is faulty.
Replace the SPM or SPM control printed circuit board.
(b) The CNC is faulty.
Replace the board or module related to the serial spindle.
3.4.2.12 Alarm code 54
-s
p
A large current flowing in the motor for a long time was detected.
uc
Troubleshoot as in the case of alarm code 29.
an
3.4.2.13 Alarm code 55
ht
tp
://
w
w
w
.g
ef
In spindle switching control or output switching control, a mismatch
between the switching request signal (SPSL or RSL) and the power line
state check signal (MCFN, MFNHG, RCH, or RCHHG) continues
during motor activation.
Troubleshooting when this alarm is issued
(a) The magnetic contactor (switch unit) for power line
switching is faulty.
If the contact is inoperative, check the power supply of the
magnetic contactor. If the magnetic contactor is still
inoperative, replace the magnetic contactor.
(b) The I/O unit or wiring for checking the contact of the
magnetic contactor is faulty.
If a defect is found in the I/O unit or wiring, replace the I/O
unit or wiring.
(c) The sequence (ladder) is incorrect.
Modify the sequence so that switching is not performed
during activation. For details of the signals, refer to Chapter
10, "Interface Signals," in "FANUC SERVO AMPLIFIER α
series Descriptions (B-65162E)."
- 168 -
TROUBLESHOOTING
B-65165E/02
3. TROUBLESHOOTING
AND ACTION
3.4.2.14 Alarm code 56
ar
es
.co
m
/
The cooling fan of the control circuit stopped.
When this alarm is issued, replace the SPM or the internal cooling
fan of the SPM. When replacing the internal cooling fan, see
Chapter 4.
3.4.2.15 Alarm code 57
The temperature of the regenerative resistance of the PSM (resistance
regenerative type) is excessively high. The PSM is faulty.
uc
-s
p
(1) If the PSM indicates alarm code 8 or above
Troubleshoot according to the description of alarm code 8 (or the
pertinent code) provided in Section 3.1 of Part II.
w
.g
ef
an
(2) If the PSM indicates no alarm
(a) A cable is faulty.
The connection cable between the PSM (JX1B) and SPM
(JX1A) is faulty. Replace the cable.
(b) The SPM is faulty.
Replace the SPM or SPM control printed circuit board.
ht
tp
://
w
w
3.4.2.16 Alarm code 58
The temperature of the main circuit-cooling fan of the PSM is
abnormally high.
(1) If the PSM indicates alarm code 3
Troubleshoot according to the description of alarm code 3
provided in Section 3.1 of Part II.
(2) If the PSM indicates no alarm
(a) A cable is faulty.
The connection cable between the PSM (JX1B) and SPM
(JX1A) is faulty. Replace the cable.
(b) The SPM is faulty.
Replace the SPM or SPM control printed circuit board.
- 169 -
3. TROUBLESHOOTING
AND ACTION
TROUBLESHOOTING
B-65165E/02
3.4.2.17 Alarm code 59
ar
es
.co
m
/
The internal cooling fan of the PSM stopped.
(1) If the PSM indicates alarm code 2
Troubleshoot according to the description of alarm code 2
provided in Section 3.1 of Part II.
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
(2) If the PSM indicates no alarm
(a) A cable is faulty.
The connection cable between the PSM (JX1B) and SPM
(JX1A) is faulty. Replace the cable.
(b) The SPM is faulty.
Replace the SPM or SPM control printed circuit board.
- 170 -
TROUBLESHOOTING
B-65165E/02
3.4.3
3. TROUBLESHOOTING
AND ACTION
αC Series Spindle Amplifier Module
3.4.3.1
ar
es
.co
m
/
For the αC series, only those alarm codes that have the same number as
for the α series and require troubleshooting different from the α series
are described.
For an alarm code not covered by this subsection, see the description of
the alarm code for the α series spindle amplifier module.
Alarm code 12
-s
p
An excessively high motor current was detected.
An excessively high current flowed into the DC link of the main circuit.
uc
For SPMC-2.2 to SPMC-11
The power module (IPM) of the main circuit detected an excessive load,
excessively high current, or decrease in control supply voltage.
an
(1) If an SPMC from SPMC-2.2 to SPMC-11 indicates this alarm
Check alarm code 09 as well.
ht
tp
://
w
w
w
.g
ef
(2) If this alarm is issued immediately after a spindle move command
is specified
(a) The motor power line is faulty.
Check for a short circuit between motor power lines and
short-circuit to ground, and replace the power line as
required.
(b) The motor winding has an insulation failure.
If the motor is short-circuited to ground, replace the motor.
(c) The parameters specific to the motor are not set correctly.
Refer to "FANUC AC SPINDLE MOTOR α series
Parameter Manual (B-65160E)."
(d) The SPMC is faulty.
A power element (IGBT, IPM) may be destroyed. Replace
the SPMC.
(3) If this alarm is issued during spindle rotation
(a) Belt slippage
The belt between the spindle and motor may be slipping.
Clean the pulley and run the belt again.
(b) The parameters specific to the motor are not set correctly.
Referring to "FANUC AC SPINDLE MOTOR α series
Parameter Manual (B-65160E)," check the parameters
specific to the motor.
- 171 -
3. TROUBLESHOOTING
AND ACTION
TROUBLESHOOTING
B-65165E/02
Alarm code 35
-s
p
3.4.3.2
ar
es
.co
m
/
(c) A power element is destroyed.
A power element (IGBT, IPM) may be destroyed. Replace
the SPM.
If the amplifier setting condition is not satisfied, or cooling is
insufficient because the heat sink is dirty, the power
elements may be destroyed.
When the heat sink on the back of the amplifier is too dirty,
clean the heat sink, for example, by blowing air. Consider
the use of a structure that prevents the heat sink from being
directly exposed to coolant.
For the setting condition, refer to "FANUC SERVO
AMPLIFIER α series Descriptions (B-65162E)."
uc
The motor speed calculated from the position coder much differs from
the motor speed estimated in the SPMC.
ht
tp
://
w
w
w
.g
ef
an
(1) If this alarm is issued when a rotation command is specified
(a) The setting of parameters for position coder setting is
incorrect.
Set the bits related to the rotation directions of the position
coder and spindle and the rotation directions of the spindle
and motor. For details, refer to "FANUC AC SPINDLE
MOTOR α series Parameter Manual (B-65160E)."
(b) The setting of parameters for gear ratio setting is incorrect.
Check if incorrect gear ratio data is set. The gear ratio data is
used for conversion from the position coder to a motor speed.
So, be sure to set correct values.
FS0
6556
to
6559
FS15i
3056
to
3059
FS16i/16, PM-D/F
Description
4056
Gear ratio between the spindle and
to
motor
4059
(c) Slippage between the spindle and motor
Make an adjustment to prevent the belt from slipping.
(2) If this alarm is issued during cutting
The motor speed is decreased because of an overload. Review the
cutting condition.
- 172 -
TROUBLESHOOTING
B-65165E/02
3.5
3. TROUBLESHOOTING
AND ACTION
POWER-FAILURE BACKUP MODULE
ar
es
.co
m
/
When an alarm is issued, the one-digit 7-segment LED indicates an
alarm code.
Indicates an alarm code (01 or above).
3.5.1
Alarm Code 1
-s
p
(1) Meaning
Sub-module C cannot be charged.
Alarm Code 2
w
.g
3.5.2
ef
an
uc
(2) Cause and troubleshooting
(a) Sub-module C connection error
→ Check the connection.
(b) Charging circuit failure
→ Replace the power-failure backup module.
(2) Cause and troubleshooting
(a) Charging circuit failure
→ Replace the power-failure backup module.
://
w
w
(1) Meaning
After sub-module C was charged, the voltage decreased for a
cause.
ht
tp
3.5.3
Alarm Code 3
(1) Meaning
An abnormal current flowed in sub-module R.
(2) Cause and troubleshooting
(a) Excessive regenerated power
→ If the sum of maximum servo motor outputs exceeds 20
kW, use two sub-module R units.
(b) Regenerative circuit failure
→ Replace the power-failure backup module.
- 173 -
3. TROUBLESHOOTING
AND ACTION
B-65165E/02
Alarm Code 4
ar
es
.co
m
(1) Meaning
The regenerative resistance in sub-module R is overheated.
/
3.5.4
TROUBLESHOOTING
(2) Cause and troubleshooting
(a) Sub-module R is placed in conductive state at all times
because of a regenerative circuit failure.
→ Replace the power-failure backup module.
3.5.5
Alarm Code 5
-s
p
(1) Meaning
The supply voltage for driving the thyristor decreased.
ht
tp
://
w
w
w
.g
ef
an
uc
(2) Cause and troubleshooting
(a) The power supply circuit for driving the thyristor is
abnormal.
→ Replace the power-failure backup module.
- 174 -
TROUBLESHOOTING
B-65165E/02
/
HOW TO REPLACE THE FUSES AND
PRINTED CIRCUIT BOARDS
ar
es
.co
m
4
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
WARNING
Before replacing fuses or printed-circuit boards,
make sure that the recharge-under-way LED (red) is
off.
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
Before replacing fuses or printed circuit boards, see the table given
below to find which section or subsection in this manual provides
information about the related replacement procedure.
- 175 -
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
TROUBLESHOOTING
B-65165E/02
(1) Power supply module
Drawing No.
A06B-6077-H106 to 111
A06B-6087-H115 to 137
A06B-6077-H115 to 130
A06B-6071-H115 to 130
PSM-45, 55
A06B-6087-H145 to 155
PSM-15HV to 45HV A06B-6091-H115 to 145
PSM-75HV
A06B-6087-H175
PSMR-3, 5.5
A06B-6081-H103, H106
PSMV-11HV
A06B-6098-H111
(2) Servo amplifier module
Model
Drawing No.
SVM1-240, 360
an
uc
SVM2-12/12 to
80/80
SVM3-12/12/12 to
SVM3-20/20/40
A06B-6079-H101 to H106
A06B-6096-H101 to H106
A06B-6079-H107, H108
A06B-6096-H107, H108
A06B-6079-H201 to H209
A06B-6096-H201 to H209
A06B-6079-H301 to H307
A06B-6080-H301 to H307
A06B-6096-H301 to H307
A06B-6085-H102 to H104
A06B-6097-H102 to H104
A06B-6085-H201 to H206
A06B-6097-H201 to H206
-s
p
SVM1-12 to 130
ht
tp
://
w
w
w
.g
ef
SVM1-20HV to
60HV
SVM2-20/20HV to
SVM2-60/60HV
- 176 -
Fuse
replacement
4.2.1(1)
4.2.1(1), (3)
4.2.1(2), (3)
4.2.1(2), (3)
4.2.1(1)
4.2.1(1), (3)
4.2.1(1)
4.2.1(4), (5)
4.2.1(1), (6)
ar
es
.co
m
PSM-5.5 to 11
PSM-15 to 37
Case
disassembly
4.1.1
4.1.2
4.1.2
4.1.3
4.1.4
4.1.2
4.1.4
4.1.1
4.1.2
/
Model
Case
Fuse
disassembly replacement
4.1.1
4.2.2(1)
4.1.2
4.1.1
4.2.2(1),
4.2.3(2)
4.2.2(1)
4.1.1
4.2.2(1)
4.1.1
4.2.2(1)
4.1.1
4.2.2(1)
TROUBLESHOOTING
B-65165E/02
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
(3) Spindle amplifier module (In drawing numbers, # and the
subsequent part is omitted.)
A06B-6102-H202 to H211
A06B-6102-H102 to H111
A06B-6102-H215 to H230
A06B-6102-H115 to H130
A06B-6102-H245, H255
A06B-6102-H145, H155
A06B-6078-H102 to H211
A06B-6078-H302 to H311
4.2.3(1), (2)
4.3.1(1)
4.1.4
4.2.3(1)
4.3.1(1)
4.1.1
4.1.2
4.1.3
4.1.4
an
uc
A06B-6088-H411 to H430
A06B-6088-H245, H255
A06B-6088-H345, H355
A06B-6088-H145, H155
A06B-6088-H445
A06B-6078-H215 to H330
A06B-6078-H411
A06B-6082-H202 to H211
A06B-6082-H215 to H226
A06B-6104-H211
A06B-6104-H111
A06B-6104-H215 to H245
A06B-6104-H115 to H145
A06B-6104-H275
A06B-6104-H175
A06B-6092-H211
A06B-6092-H311
A06B-6092-H111
A06B-6092-H215 to H245
A06B-6092-H315 to H345
A06B-6092-H115 to H145
A06B-6092-H275
A06B-6092-H375
A06B-6092-H175
A06B-6092-H415 to H445
A06B-6092-H475
w
.g
w
w
://
tp
ht
4.1.2
4.3.1(2)
4.2.3(2)
-s
p
A06B-6088-H115 to H230
A06B-6088-H315 to H330
ef
SPM-2.2 to 11 TYPE1
TYPE4
SPM-15 to 30 TYPE1
TYPE4
SPM-45 to 55 TYPE1
TYPE4
SPM-2.2 to 11 TYPE1
TYPE2
TYPE4
SPM-15 to 30 TYPE1
TYPE2
TYPE4
SPM-11 to 30 TYPE3
SPM-45 to 55 TYPE1
TYPE2
TYPE4
SPM-45 TYPE3
Old SPM15 to 30
Old SPM11
SPMC2.2 to 11
SPMC15 to 26
SPM11HV TYPE1
TYPE4
SPM15HV to 45HV TYPE1
TYPE4
SPM75HV TYPE1
TYPE4
SPM11HV TYPE1
TYPE2
TYPE4
SPM15HV to 45HV TYPE1
TYPE2
TYPE4
SPM75HV TYPE1
TYPE2
TYPE4
SPM15HV to 45HV TYPE3
SPM75HV TYPE3
/
Drawing No.
ar
es
.co
m
Model
Replacement of
the program ROM
Case
Fuse
disassembly replacement and the spindle
sensor module
4.1.1
4.2.3(1)
4.3.1(1)
4.2.3(2)
4.2.3(2)
4.3.1(2)
4.3.1(3)
4.3.1(2)
4.1.5
4.1.3
4.1.3
4.1.1
4.1.2
4.1.1
4.2.3(2)
4.2.3(1)
4.3.1(3)
4.3.1(6), (7)
4.3.1(7)
4.3.1(4)
4.3.1(5)
4.3.1(1)
4.1.2
4.2.3(1), (2)
4.3.1(1)
4.1.4
4.2.3(1)
4.3.1(1)
4.2.3(2), (3)
4.2.3(2), (3)
4.1.1
4.1.2
4.3.1(2)
4.2.3(2)
4.1.4
4.1.4
4.1.5
4.3.1(2)
4.3.1(2)
4.2.3(2)
4.3.1(3)
4.3.1(3)
(4) Power-failure backup module
Drawing No.
A06B-6077-H001
A06B-6077-H002
- 177 -
Case disassembly Fuse replacement
4.1.1
4.2.4(1)
4.1.1
4.2.4(1)
TROUBLESHOOTING
CASE DISASSEMBLY
4.1.1
60/90 mm Width Modules
/
4.1
B-65165E/02
ar
es
.co
m
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
Make sure that the recharge-under-way LED (red) is off.
uc
-s
p
Recharge-under-way
LED
an
Remove the face plate.
Remove the cases.
ht
tp
://
w
w
w
.g
ef
Remove the face plate
by inserting the tip of a
flat-blade screwdriver
at the hooks (four) on
the face plate.
- 178 -
Face plate
TROUBLESHOOTING
B-65165E/02
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
Case 2
(cover)
ar
es
.co
m
/
Case 1
(chassis)
Remove the screws fastening the case
and the screws (5 × M4) holding down
the terminal board.
Remove the printed-circuit board.
• Cases for the SVM
Control circuit board
Wiring board
-s
p
Control circuit
printed-circuit
board
Remove the screws (2 × M3) fastening the
printed-circuit board.
an
uc
• Cases for the PSM and SPM
Control circuit board
ef
Remove the screws (4 × M3) fastening the
printed-circuit board.
w
.g
Remove the IPM.
IPM
<1> Remove the screws (5 × M5) fastening the IPM.
Wiring board
Then remove the wiring board.
w
w
<2> Remove the IPM.
Note)
There is a snubber capacitor between the IPM
and wiring board. When re-assembling, do not
ht
tp
://
forget to mount it.
- 179 -
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
4.1.2
TROUBLESHOOTING
B-65165E/02
150 mm Width Module (without the Connector Module)
ar
es
.co
m
/
Make sure that the recharge-under-way LED (red) is off.
The recharge-under-way LED (red) is at the center of terminal board
TB1. Open the cover at the top of the module, and check the LED.
Recharge-under-way
LED
Terminal
board
Face plate
w
.g
ef
an
uc
Remove the face plate
by inserting the tip of a
flat-blade screwdriver
at the hooks (six) on
the face plate.
-s
p
Remove the face plate.
Remove the case.
8×ネジ
Screws (eight)
ファン
Fan
w
w
ケースを取り付けて
放
熱
Heat
器
ht
tp
://
sink
- 180 -
ケース
Case
Remove
the screws
いるネジ(8ヶ所)
(eight)
fastening the
を外し、ケースをフ
cases,
and remove
ランジ面から手前に
the
case by pulling it
引いて外します。
off the flange
surface.
TROUBLESHOOTING
B-65165E/02
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
Remove the printed-circuit board.
PCB supports (two)
Wiring
board
Heat
sink
Printed-circuit
board
ar
es
.co
m
/
Fan
Printed-circuit
board
PCB support
Hook
Remove the IGBT.
uc
TB1
-s
p
While spreading the PCB support hooks, pull the printed-circuit
board off the flange surface to remove it.
an
<1> Remove terminal board TB1 (for SPM
only).
<2> Remove the electrolytic capacitor
board.
ef
<3> Remove the wiring board.
<4> Remove the IGBT.
w
.g
Capacitor board
? ? ?
IGBT
ht
tp
://
w
w
Wiring
board
- 181 -
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
4.1.3
TROUBLESHOOTING
B-65165E/02
150 mm Width Module (with the Connector Module)
ar
es
.co
m
/
Make sure that the recharge-under-way LED (red) is off.
The recharge-under-way LED (red) is at the center of terminal board
TB1. Open the cover at the top of the module, and check the LED.
Recharge-under-way
LED
Terminal
board
Face plate
w
.g
ef
an
uc
Remove the face
plate by inserting
the tip of a flat-blade
screwdriver at the
hooks (six) on the
face plate.
-s
p
Remove the face plate.
Remove connector PCB.
w
w
Remove the self-tapping screws holding down
connector PCB, and shift it in the direction
indicated with an arrow (left) to remove the
printed-circuit board.
ht
tp
://
Connector PCB
- 182 -
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
TROUBLESHOOTING
B-65165E/02
Remove the case.
8×ネジ
Screws
(eight)
/
ファン
Fan
ケース
Case
-s
p
熱
Heat
器
sink
ar
es
.co
m
放
ケースを取り付けて
Remove the screws
いるネジ(8ヶ所)
(eight) fastening the
を外し、ケースをフ
cases, and remove
ランジ面から手前に
the case by pulling it
off the flange
引いて外します。
surface.
Remove the printed-circuit board.
uc
PCB supports (two)
Wiring
board
Printed-circuit
board
Printed-circuit
board
w
.g
ef
Heat
sink
an
Fan
PCB support
w
w
Hook
ht
tp
://
While spreading the PCB support hooks, pull the printed-circuit
board off the flange surface to remove it.
- 183 -
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
TROUBLESHOOTING
B-65165E/02
Remove the IGBT.
/
TB1
ar
es
.co
m
<1> Remove terminal board TB1
(for SPM only).
<2> Remove the electrolytic
capacitor board.
<3> Remove the wiring board.
<4> Remove the IGBT.
Capacitor board
an
uc
-s
p
Wiring
board
ht
tp
://
w
w
w
.g
ef
IGBT
- 184 -
Wiring
board
TROUBLESHOOTING
B-65165E/02
4.1.4
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
300-mm Wide Module (without the Connector Module)
ar
es
.co
m
/
Make sure that the recharge-under-way LED (red) is off. View the
recharge-under-way LED (red) from the upper part of the DC link
cover.
LED
uc
-s
p
Cover
Remove the DC link cover and motor power line cover.
Remove the self-tapping
screws (8 × M4) from
the DC link cover and
motor power line cover.
w
.g
ef
an
DC link
cover
Remove the face plate.
://
w
w
Motor power
line cover
ht
tp
Remove the screws
(5 × M4) from the
face plate.
Screw (× 5)
- 185 -
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
TROUBLESHOOTING
B-65165E/02
ar
es
.co
m
/
Remove the right side plate.
Remove the
screws (7 × M4)
from the right side
plate.
Right side plate
Heat sink
-s
p
Screw (7 × M4)
uc
Remove the control printed circuit board.
Control printed circuit
board
ef
Heat sink
an
Bottom plate
w
.g
PCB support
Control printed circuit
board
Hook
PCB support
Wiring board
ht
tp
://
w
w
Insert the tip of a screwdriver into the opening on the bottom
plate, and while spreading the hook of the PCB support, pull
the printed circuit board off the flange surface toward you.
- 186 -
TROUBLESHOOTING
B-65165E/02
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
Remove the LED board for the recharge indicator.
LED board for the recharge indicator
ar
es
.co
m
/
Remove the
screws (2 × M4)
from the LED
board, and remove
the board.
Heat sink
Screw (× 2)
-s
p
Remove the top plate.
w
w
uc
w
.g
ef
an
Screw (2 × M5)
Top plate
Screw (5 × M4)
<1> From the two connectors,
detach the cables of the current
sensor.
<2> Remove the screws (3 × M4)
from the driver printed circuit
board.
<3> Pull up the driver printed circuit
board to remove it.
Screw × 3
://
tp
Heat sink
Remove the driver printed circuit board.
Driver printed circuit board
ht
<1> Remove the screws (2 × M5)
from the DC link jumper.
<2> Remove the screws (5 × M4)
from the top plate.
<3> Remove the top plate. (The top
plate comes off together with
the terminal block TB1.)
Connector × 2
- 187 -
Carefully insert the tip of a screwdriver
and pull out the cable. (Be careful not
to force the screwdriver into the
connector; otherwise, the claw may
break.)
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
TROUBLESHOOTING
B-65165E/02
Remove the left side and bottom plates.
Screw (2 × M5)
Electrolytic
capacitor
<1> Locate the jumpers that connect the
terminal block TB2 and the wiring
board. Remove the screws (3 ×
M6) holding the jumpers to the
wiring board.
<2> Remove the screws (2 × M5) that
connect the capacitor and jumpers.
<3> Remove the screws (6 × M4) from
the left side and bottom plates.
<4> Remove the left side and bottom
plates. (These plates come off
together with the electrolytic
capacitor and terminal block TB2.)
-s
p
Screw (3 × M6)
ar
es
.co
m
/
Wiring board
Bottom plate
an
uc
Left side plate
ht
tp
://
w
w
w
.g
ef
Screw (6 × M4)
- 188 -
TROUBLESHOOTING
B-65165E/02
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
ar
es
.co
m
<1> Remove the screws that connect the IGBT
and wiring board (9 × M6, 12 × M4).
<2> Remove the screws of the thermostat TH1
(2 × M4).
<3> Remove the screws that connect the wiring
board and heat sink (2 × M4, 1 × M5).
<4> Remove the wiring board.
/
Remove the power printed circuit board.
TH1
uc
-s
p
Wiring board
an
FG
://
w
w
w
.g
ef
Remove the IGBT.
ht
tp
IGBT
- 189 -
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
4.1.5
TROUBLESHOOTING
B-65165E/02
300-mm Wide Module (with the Connector Module)
ar
es
.co
m
/
Make sure that the recharge-under-way LED (red) is off. View the
recharge-under-way LED (red) from the upper part of the DC link
cover.
LED
uc
-s
p
Cover
Remove the DC link cover and motor power line cover.
Remove the self-tapping
screws (8 × M4) from
the DC link cover and
motor power line cover.
w
.g
ef
an
DC link
cover
Remove the face plate.
://
w
w
Motor power
line cover
ht
tp
Remove the screws (5 × M4)
from the face plate.
Screw (× 5)
- 190 -
TROUBLESHOOTING
B-65165E/02
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
Plate
ar
es
.co
m
/
Remove the right side plate.
Heat sink
Remove the
screws (7 × M4)
from the right side
plate.
-s
p
Screw (7 × M4)
Remove the connector module and plate.
<1>
uc
Plate
<2>
<3>
Remove the screws (3 × M3) from the
connector module.
Pull the connector module out of the
control printed circuit board.
Remove the screws (4 × M4) from the
plate, and remove the plate.
Screw (4 × M4)
Connector module
w
.g
ef
an
Control printed
circuit board
ht
tp
://
w
w
Screw (3 × M3)
- 191 -
Upper side plate
Bottom plate
Heat sink
Heat sink
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
TROUBLESHOOTING
B-65165E/02
Bottom plate
ar
es
.co
m
Control printed
circuit board
/
Remove the control printed circuit board.
Control printed circuit
board
Heat sink
Hook
PCB support
PCB support
Wiring board
-s
p
Insert the tip of a screwdriver into the opening on the bottom
plate, and while spreading the hook of the PCB support, pull the
printed circuit board off the flange surface toward you.
uc
Remove the LED board for the recharge indicator.
LED board for the recharge indicator
ef
an
Remove the
screws (2 × M4)
from the LED
board, and remove
the board.
ht
tp
://
w
w
w
.g
Screw (x 2)
- 192 -
Heat sink
TROUBLESHOOTING
B-65165E/02
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
Screw (2 × M5)
Heat sink
Top plate
<1> Remove the screws (2 × M5)
from the DC link jumper.
<2> Remove the screws (5 × M4)
from the top plate.
<3> Remove the top plate. (The top
plate comes off together with
the terminal block TB1.)
-s
p
Screw (5 × M4)
ar
es
.co
m
/
Remove the top plate.
Screw × 3
ef
an
Driver printed circuit board
uc
Remove the driver printed circuit board.
ht
tp
://
w
w
w
.g
Connector × 2
- 193 -
<1> From the two connectors,
detach the cables of the current
sensor.
<2> Remove the screws (3 × M4)
from the driver printed circuit
board.
<3> Pull up the driver printed circuit
board to remove it.
Carefully insert the tip of a screwdriver
and pull out the cable. (Be careful not
to force the screwdriver into the
connector; otherwise, the claw may
break.)
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
TROUBLESHOOTING
B-65165E/02
Remove the left side and bottom plates.
Screw (2 × M5)
Electrolytic
capacitor
<1> Locate the jumpers that connect the
terminal block TB2 and the wiring
board. Remove the screws (3 × M6)
holding the jumpers to the wiring
board.
<2> Remove the screws (2 × M5) that
connect the capacitor and jumpers.
<3> Remove the screws (6 × M4) from
the left and bottom plates.
<4> Remove the left and bottom plates.
(These plates come off together with
the electrolytic capacitor and
terminal block TB2.)
-s
p
Screw (3 × M6)
ar
es
.co
m
/
Wiring board
Bottom plate
an
uc
Left side plate
ht
tp
://
w
w
w
.g
ef
Screw (6 × M4)
- 194 -
TROUBLESHOOTING
B-65165E/02
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
Remove the power printed circuit board.
ar
es
.co
m
/
<1> Remove the screws that connect the IGBT
and wiring board (9 × M6, 12 × M4).
<2> Remove the screws of the thermostat TH1
(2 × M4).
<3> Remove the screws that connect the wiring
board and heat sink (2 × M4, 1 × M5).
<4> Remove the wiring board.
TH1
uc
-s
p
Wiring board
an
FG
://
w
w
w
.g
ef
Remove the IGBT.
ht
tp
IGBT
- 195 -
TROUBLESHOOTING
REPLACING FUSES
4.2.1
Power Supply Module
/
4.2
B-65165E/02
ar
es
.co
m
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
(1) Replacing fuses on the control printed circuit board
a) F1 for 200 V for the control power
b) F2 for 200 V for CX1B external cooling fan
For A16B-2202-0423 to 0424 only.
Specification drawing No.
F1 (FU1)
F2 (FU2)
A60L-0001-0359
A60L-0001-0175#2.0A
F1 (FU1)
250V F5.0A DAITO HM50
250V F2.0A DAITO HM20
Control printed circuit board
(A16B-2202-0420 to 0424)
(A16B-2203-0220)
ef
an
uc
F2 (FU2)
Remarks
-s
p
Fuse
w
.g
(2) Replacing a fuse on the control printed circuit board
a) F1 for 200 V for the control power
Fuse
A60L-0001-0245#GP75
Remarks
250V F7.5A DAITO GP75
F1
tp
://
w
w
F1
Specification drawing No.
Control printed circuit board
ht
(A16B-2202-0080)
- 196 -
TROUBLESHOOTING
B-65165E/02
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
Specification drawing No.
F1
A60L-0001-0175#0.5A
F1
Remarks
ar
es
.co
m
Fuse
250V F0.5A DAITO HM05
Power printed circuit board
-s
p
(A20B-1005-0590 to 0592)
an
uc
(4) Replacing a fuse on the control printed circuit board
a) F1 for 200 V for the control power
Fuse
Specification drawing No.
A60L-0001-0175#5.0A
Remarks
250V F5.0A DAITO HM50
F1
Control printed circuit board
w
w
w
.g
ef
F1
ht
tp
://
(A16B-2201-0890)
- 197 -
/
(3) Replacing a fuse on the power printed circuit board
a) F1 for the external cooling fan
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
TROUBLESHOOTING
B-65165E/02
F1
Specification drawing No.
A60L-0001-0359
Remarks
250V F5.0A DAITO HM50
F1
ar
es
.co
m
Fuse
Control printed circuit board
-s
p
(A16B-2300-0100)
an
uc
(6) Replacing fuses on the AC reactor
a) F1 to F3 for main circuit protection
Fuse
Specification drawing No.
Remarks
A60L-0001-0362#100U
CR6L-100/UL
F1
ef
F2
L11
F1
400R
L21
F2
400S
L31
F3
400T
AC reactor (A81L-0001-0144)
ht
tp
://
w
w
w
.g
F3
- 198 -
/
(5) Replacing a fuse on the power printed circuit board
a) F1 for 200 V for the external cooling fan
TROUBLESHOOTING
B-65165E/02
Servo Amplifier Module
ar
es
.co
m
(1) Replacing a fuse on the unit (control printed circuit board)
a) F1 for the 24-V control power
Fuse
Specification drawing No.
Remarks
F1
A60L-0001-0290#LM32C
48V F3.2A DAITO LM32C
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
F1
- 199 -
/
4.2.2
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
B-65165E/02
Spindle Amplifier Module
ar
es
.co
m
(1) Replacing a fuse on the control printed circuit board
a) F1 for the 24-V control power
Fuse
Specification drawing No.
Remarks
F2
A60L-0001-0290#LM32C
48V F3.2A DAITO LM32C
F1
Control printed circuit board
uc
-s
p
(A16B-2203-050x)
an
(2) Replacing a fuse on the power printed circuit board
a) F2 for 200 V for the external cooling fan
Specification drawing No.
Remarks
F2
A60L-0001-0175#0.5A
250V F5.0A DAITO HM50
w
.g
ef
Fuse
w
w
F2
Wiring board
(A20B-1005-057x,
ht
tp
://
A20B-1006-048x, -055x, -0890)
- 200 -
/
4.2.3
TROUBLESHOOTING
TROUBLESHOOTING
B-65165E/02
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
Specification drawing No.
F2
A60L-0001-0290#LM50C
50V F5.0A DAITO LM50C
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
F2
Remarks
ar
es
.co
m
Fuse
- 201 -
/
(3) Replacing a fuse on the unit (control printed circuit board)
a) F2 for the 24-V control power
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
4.2.4
TROUBLESHOOTING
B-65165E/02
Power-Failure Backup Module
Fuse
Specification drawing No.
FU1
A60L-0001-0396#10A
FU2
A60L-0001-0290#LM32C
FU1
216-010 (ECX)
48V F3.2A DAITO LM32
uc
FU2
Remarks
-s
p
FU3
ar
es
.co
m
/
(1) Replacing fuses on the unit (control printed circuit board)
a) FU1 for 200 V for the control power
b) FU2 for 200 V for the control power
Fuses a) and b) above are provided for A16B-2203-0020
only.
c) FU3 for the 24-V control power
ht
tp
://
w
w
w
.g
ef
an
FU3
- 202 -
Control printed circuit board
(A16B-2002-0790, A16B-2003-0020)
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
TROUBLESHOOTING
B-65165E/02
OTHER COMPONENTS
4.3.1
Replacing the SPM Program ROM and Spindle Sensor Module
(1) SPM type 1 and type 4
Name
ROM
ar
es
.co
m
/
4.3
Spindle sensor module
D4
Specification drawing No.
Remarks
A06B-6102-H520
9D20 series
A20B-2902-0620
For type 4 only
ROM (Note that the notch is upward.)
Spindle sensor module: For A16B-2203-0503-0505 only
-s
p
AM1
an
uc
Control printed circuit board (A16B-2203-0500-0505)
NOTE
For SPM type 4, the revision of the control printed
circuit board must be the following:
A16B-2202-0433, 0434: 16E or later
A16B-2202-0435: 13C or later
ht
tp
://
w
w
w
.g
ef
(2) SPM types 1 to 4
The drawing number of the spindle sensor module differs
depending on the SPM type as follows:
SPM type 2: A20B-2901-0851
Mounting location = MD4, MD5, MD6
SPM type 4: A20B-2902-0620 (old specification A20B-29020610 also allowed)
Mounting location = MD4, MD6
- 203 -
TROUBLESHOOTING
B-65165E/02
Name
Specification drawing No.
Remarks
ROM
A06B-6072-H500
9D0A series
Spindle sensor module
See the above table.
MD4, 5, 6
/
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
ar
es
.co
m
MD4
MD6
Spindle sensor module × 3
MD5
ROM
MG11
Control printed circuit board
Name
Specification drawing No.
Remarks
ROM
A06B-6072-H500
9D0A series
Spindle sensor module
A20B-2901-0851
uc
(3) SPM type 3
-s
p
(A16B-2202-0430 to 0435, A16B-2203-0330 to 0332)
ef
an
MD4
Spindle sensor module
ROM
Control printed circuit board (A06B-2202-0440)
(4) SPMC-2.2 to 11
Name
Specification drawing No.
Remarks
ROM
A06B-6082-H512
9D12 series
ROM
A06B-6082-H511
9D11 series
ROM
A06B-6082-H510
9D10 series
ht
tp
://
w
w
w
.g
MG11
Control printed circuit board (A20B-2001-0780, 0781)
MC8
ROM
- 204 -
4. HOW TO REPLACE THE FUSES
AND PRINTED CIRCUIT BOARDS
TROUBLESHOOTING
B-65165E/02
(5) SPMC-15 to 26
Specification drawing No.
Remarks
ROM
A06B-6082-H512
9D12 series
ROM
D8
ROM
ar
es
.co
m
ROM
/
Name
A06B-6082-H511
9D11 series
A06B-6082-H511
9D10 series
Control printed circuit board (A06B-2202-0840)
-s
p
(6) SPM type 1 of old specification
w
w
A20B-2901-0851
Control printed circuit board (A06B-2202-0070)
(7) SPM types 2 and 3 of old specification
MF4
Name
Specification drawing No.
Remarks
ROM
A06B-6072-H500
9D0A series
Spindle sensor module
A20B-2901-0851
ROM
tp
://
9D0A series
Spindle sensor module × 1
w
.g
ef
MD3
ht
Remarks
A06B-6072-H500
Spindle sensor module
an
ROM
Specification drawing No.
ROM
uc
MF4
Name
MD6
MD3
Spindle sensor module × 4
Control printed circuit board (A06B-2202-0160)
- 205 -
://
tp
ht
w
w
w
.g
ar
es
.co
m
-s
p
uc
an
ef
III. MOTOR MAINTENANCE
/
AC SERVO MOTOR MAINTENANCE
ar
es
.co
m
1
/
MOTOR MAINTENANCE
B-65165E/02
1. AC SERVO MOTOR
MAINTENANCE
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
Generally, AC servo motors have no parts that wear off or that must be
replaced periodically, unlike DC servo motors, which have brushes that
must be replaced periodically.
However, you should perform periodic maintenance for servo motors
so as to keep their initial performance as long as possible and to prevent
breakdowns. AC servo motors have precision detectors. Their
incorrect use or damage caused during transportation or assembling can
result in breakdowns or accidents. We recommend that you inspect the
servo motors periodically according to the descriptions given below.
- 209 -
1. AC SERVO MOTOR
MAINTENANCE
1.1
TROUBLESHOOTING
B-65165E/02
ar
es
.co
m
When you receive an AC servo motor, make sure that:
/
RECEIVING AND KEEPING AC SERVO MOTORS
• The motor is exactly the one you ordered, in terms of model, shaft,
and detector specifications.
• No damage has been caused on the motor.
-s
p
Because FANUC inspects servo motors strictly before shipment, you
do not, in principle, have to inspect them when you receive them.
However, you should check the specifications (wiring, current, and
voltage) of the motor and detector carefully, as required.
The servo motors should be kept indoors as a rule. The storage
temperature range is -20 to +60°C. Do not place or install AC servo
motors in the place where:
• It is extremely humid and dew is prone to form,
uc
• There is a steep change in temperature,
an
• There is constant vibration, which may cause damage to the shaft
bearings, or
ht
tp
://
w
w
w
.g
ef
• There is lots of dust and trash.
- 210 -
MOTOR MAINTENANCE
B-65165E/02
1.2
1. AC SERVO MOTOR
MAINTENANCE
DAILY INSPECTION OF AC SERVO MOTORS
ar
es
.co
m
/
Before starting operation, or periodically (once a week or month), you
should inspect the AC servo motors in terms of the following:
(1) Vibration and noise
Check the motor for abnormal vibration (by the hand) and noise
(by the ear) when the motor is:
• Not rotating
• Rotating at low speed
ef
an
uc
-s
p
• Accelerating or decelerating
If you find anything unusual, contact your FANUC service staff.
ht
tp
://
w
w
w
.g
(2) Damage on the outside
Check the motor cover (red plastic) for crevices and the motor
surface (black coating) for scratches and cracks.
If you find a crevice in the motor cover, you should replace it as
quickly as possible. For how to replace, see the description about
the pulse coder in Section 1.4. If you are not sure about
replacement, contact you FANUC service staff.
If there is a scratch or crack on the motor surface, the user should
repair it by himself as required. If coating has come off, dry the
portion of interest (or the entire surface) and coat it with paint for
machines such as urethane paint.
Replace a motor cover with a crevice or crack
as quickly as possible.
- 211 -
1. AC SERVO MOTOR
MAINTENANCE
TROUBLESHOOTING
B-65165E/02
ar
es
.co
m
/
(3) Stains and smudges
Check the motor surface and bolt holes for oil or cutting fluid.
Wipe off oil and cutting fluid on the motor surface periodically.
Oil or cutting fluid can damage the coating by chemical reaction,
possibly leading to a failure.
Also check how such a liquid leaks onto the motor, and repair if
needed.
an
uc
-s
p
Wipe off oil and cutting fluid on the motor
surface periodically.
Attach a thermolabel and
check it visually.
ht
tp
://
w
w
w
.g
ef
(4) Overheating
Check to see if the motor is too hot during normal operation.
Attach a thermolabel on the motor surface and check it visually to
see if the motor becomes too hot during normal operation.
Note) Temperature on the motor surface can exceed 80°C
under some conditions. Never touch it by the hand.
- 212 -
MOTOR MAINTENANCE
B-65165E/02
1.3
1. AC SERVO MOTOR
MAINTENANCE
PERIODIC INSPECTION OF AC SERVO MOTORS
ar
es
.co
m
/
We recommend that you inspect the AC servo motors for the following
items at least once a year.
-s
p
(1) Observation of torque command (TCMD) and speed command
(VCMD) waveforms
Observe normal voltage waveforms with an oscilloscope, and
keep notes of them. During periodic inspection, check the current
waveforms with the records.
The waveforms vary according to the operating conditions such as
load and cutting speed. Note that you should make comparisons
under the same condition (for example, during fast traverse to the
reference position or low-speed cutting).
See descriptions on the check boards in I-4.2.5 for detailed
inspection procedures.
uc
(2) Diagnosis by waveforms
Check the measured waveforms to see whether:
ht
tp
://
w
w
w
.g
ef
an
<1> The peak current is within the limit to the current in the
amplifier.
The limit to the amplifier current is listed below.
Limit to the amplifier
current
Measured waveform
0
⇒
The motor used to accelerate/decelerate with the amplifier
current within the limit (the acceleration/deceleration torque
used to be sufficient), but something is wrong now. If this is
the case, the probable causes are:
• The load conditions in the machine have changed because
of changed friction or reduced machine efficiency after
long period of use.
• Motor failure
- 213 -
1. AC SERVO MOTOR
MAINTENANCE
TROUBLESHOOTING
B-65165E/02
ar
es
.co
m
/
Increased friction
Reduced efficiency
[Table 1]
Models
ef
an
uc
-s
p
α1/3000, α2/2000, α2/3000
αM2/3000, αM2.5/3000, αC3/2000, αC6/2000, αC12/2000,
α3/3000HV, α6/3000HV
α3/3000, α6/2000, α12/2000, α22/1500, αC22/1500,
α12/3000HV, αM6/3000HV, αM9/3000HV
α22/3000HV, α30/3000HV, αM22/3000HV, αM30/3000HV
α6/3000, α12/3000, α22/2000, α30/1200, αM6/3000, αM9/3000,
αL6/3000, αL9/3000
α22/3000, α30/2000, α30/3000, α40/2000, α40/2000 (with fan),
αM22/3000, αM30/3000, αM40/3000, αL25/3000, αL50/2000
α65/2000
αM40/3000 (with fan), α100/2000, α150/2000
α300/2000, α400/2000
Current
value
12Ap
20Ap
40Ap
60Ap
80Ap
130Ap
240Ap
360Ap
360Ap × 2
w
.g
<2> The waveform has ripple during constant-speed feeding.
w
w
Ripple
tp
://
Measured waveform
ht
0
- 214 -
1. AC SERVO MOTOR
MAINTENANCE
MOTOR MAINTENANCE
B-65165E/02
<3> The current waveform has ripple or jumps when the motor is
not rotating.
ar
es
.co
m
/
Ripple
-s
p
Measured waveform
0
ht
tp
://
w
w
w
.g
ef
an
uc
If you find anything unusual in relation to the above items, contact
your FANUC service staff.
- 215 -
1. AC SERVO MOTOR
MAINTENANCE
1.4
TROUBLESHOOTING
B-65165E/02
REPLACING THE PULSE CODER
ar
es
.co
m
/
This section explains how to replace the pulse coder and motor cover,
assuming that the pulse coder has broken down and is in need of
immediate replacement.
When replacing the pulse coder and motor cover, be careful not to give
a shock to the pulse coder or motor, because they are precision devices
prone to a breakdown. Also keep them from dust and cutting chips.
-s
p
(1) Models α1, α2, αM2, αM2.5
<1> Remove the four M4 hexagonal socket head bolts that fasten
the pulse coder. Do not loosen the M3 bolts near each M4
bolt. (Removing the M3 bolts will impair airtightness.)
uc
Pulse coder cver fastening bolts M3
Pulse coder fastening bolts M4 × 16
PULSECODER
FASTENING SCREWS M4 × 16
w
.g
ef
an
PULSECODER COVER
FASTENING SCREWS M3
://
w
w
<2> Remove the pulse coder and Oldham’s coupling.
Pulse coder
tp
Pulse coder fastening bolts
ht
M4 × 16(4)
- 216 -
1. AC SERVO MOTOR
MAINTENANCE
MOTOR MAINTENANCE
B-65165E/02
-s
p
Oldham’s coupling
ar
es
.co
m
/
<3> Set a new pulse coder and a new Oldham’s coupling in the
motor. Place the Oldham’s coupling with the correct
orientation, and engage the teeth.
uc
Mate coupling of the
Oldham’s coupling
w
w
w
.g
ef
an
<4> Fasten the pulse coder with the four M4 hexagonal socket
head bolts. When tightening the bolts, be careful not to catch
the O-ring mounted on the pulse coder.
ht
tp
://
O-ring
- 217 -
1. AC SERVO MOTOR
MAINTENANCE
TROUBLESHOOTING
B-65165E/02
uc
-s
p
ar
es
.co
m
/
(2) Models α3 to α40, αM6 to αM40, αL, αC, α3HV to α30HV,
αM6HV to αM30HV
<1> Loosen the bolts that retain the red motor cover to remove
the cover. Check whether the pulse coder is of the cable
separation type (the pulse coder cable can be detached from
the red cover of the pulse coder) or of the cable nonseparation type (the cable cannot be detached from the
cover). For the replacement of a cable separation type pulse
coder, see Item <2>-1. For the replacement of a cable nonseparation type pulse coder, see Item <2>-2.
Motor cover
Connector
Cable separation
type pulse coder
ht
tp
://
w
w
w
.g
ef
an
Motor
Packing
- 218 -
Cable non-separation
type pulse coder
MOTOR MAINTENANCE
B-65165E/02
1. AC SERVO MOTOR
MAINTENANCE
<2>
ar
es
.co
m
<1>
/
<2>-1 (Cable separation type)
(a) Remove the cable of the pulse coder by using a screwdriver.
Cover
<3>
-s
p
Cover
M4 × 10
Do not loosen
these bolts.
ht
tp
://
w
w
w
.g
ef
an
uc
(b) Remove the four M4 hexagonal socket head bolts that retain
the pulse coder. Do not loosen the M3 bolts that retain the
pulse coder cover.
Oldham’s
coupling
(c) Remove the pulse coder and Oldham’s coupling.
(d) Set a new pulse coder and new Oldham’s coupling in the
motor. Although the mounting orientation is not specified in
particular, it is recommended that the pulse coder be set with
the same orientation as before the replacement. This is
because of the convenience of cabling. Place the Oldham’s
coupling with the correct orientation, and engage the teeth.
(e) Fasten the pulse coder with the four M4 hexagonal socket
head bolts.
- 219 -
1. AC SERVO MOTOR
MAINTENANCE
TROUBLESHOOTING
B-65165E/02
Replace the packing on the motor cover mounting surface.
Reusing old packing cannot provide sufficient sealing
performance. Whenever taking off the motor cover, be sure
to replace the packing.
(g) Connect the cable of the pulse coder.
(h) Install the motor cover. Be careful not to catch the lead wires
of the pulse coder. After installing the motor cover, fasten
the cover using the M4 hexagonal socket head bolts.
ar
es
.co
m
/
(f)
w
.g
ef
an
uc
-s
p
<2>-2 (Cable non-separation type)
(a) Detach the cannon connector of the pulse coder from the red
motor cover.
(a)-1 Remove the M3 screw that retains the connector.
(a)-2 Shift the rubber packing, and remove the C-ring that
retains the insulator on the rear side (connection side)
of the connector to separate the connector housing
from the terminal section. Replace the rubber
packing with a new one.
(a)-3 Remove the connector terminal section from the
motor cover.
(a)-4 Set the housing in the removed pulse coder (the pulse
coder to be replaced with a new one) in place, and
hold the housing with the C-ring.
(b) Cut the lead wires of the thermal switch. The wires should
be cut at the root of the crimp terminals where possible.
(c) Remove the four M4 hexagonal socket head bolts that retain
the pulse coder. Do not loosen the M3 bolts that retain the
pulse coder cover.
w
w
M4 × 10
ht
tp
://
Do not loosen
these bolts.
Oldham’s
coupling
(d) Remove the pulse coder and Oldham’s coupling.
- 220 -
MOTOR MAINTENANCE
B-65165E/02
1. AC SERVO MOTOR
MAINTENANCE
Cannon connector
Thermal wire
Cut the wire at the root of
the crimp terminal.
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
ar
es
.co
m
/
(e) Set a new pulse coder and new Oldham’s coupling in the
motor. Although the mounting orientation is not specified in
particular, it is recommended that the pulse coder be set with
the same orientation as before the replacement. This is
because of the convenience of cabling. Place the Oldham’s
coupling with the correct orientation, and engage the teeth.
(f) Fasten the pulse coder with the four M4 hexagonal socket
head bolts.
(g) Replace the packing on the motor cover mounting surface.
Reusing old packing cannot provide sufficient sealing
performance. Whenever taking off the motor cover, be sure
to replace the packing.
(h) Install the connector in the cover in the reverse order of step
(a). Keying is provided for the connector insulator (the
insulating material around the terminals). So, perform
keying (phase) alignment when installing the connector.
(i) Connect the lead wires of the thermal switch. Peel off about
1 cm of the jacket from the cut end of each motor lead wire,
and tie the wire to the terminal of the pulse coder. Use of a
crimp terminal is recommended for connection. (In case of
an emergency, insulate both connection portions with
insulating tape.)
(j) Install the motor cover. Be careful not to catch the lead wires
of the pulse coder. After installing the motor cover, bolt the
cover.
- 221 -
1. AC SERVO MOTOR
MAINTENANCE
TROUBLESHOOTING
B-65165E/02
-s
p
ar
es
.co
m
/
(3) Models α65 to α150
<1> Loosen the bolts that retain the red motor cover to remove
the cover. Check whether the pulse coder is of the cable
separation type (the pulse coder cable can be detached from
the red cover of the pulse coder) or of the cable nonseparation type (the cable cannot be detached from the
cover). For the replacement of a cable separation type pulse
coder, see Item <2>-1. For the replacement of a cable nonseparation type pulse coder, see Item <2>-2.
uc
Connector
Cable non-separation
type pulse coder
an
Cable separation
type pulse coder
w
.g
ef
<2>-1 (Cable separation type)
(a) Remove the cable of the pulse coder by using a screwdriver.
<1>
<2>
w
w
Cover
://
<3>
ht
tp
Cover
(b) Remove the four M4 hexagonal socket head bolts that retain
the pulse coder. Do not loosen the M3 bolts that retain the
pulse coder cover.
(c) Remove the pulse coder and Oldham’s coupling.
- 222 -
MOTOR MAINTENANCE
B-65165E/02
1. AC SERVO MOTOR
MAINTENANCE
-s
p
ar
es
.co
m
/
(d) Set a new pulse coder and new Oldham’s coupling in the
motor. Although the mounting orientation is not specified in
particular, it is recommended that the pulse coder be set with
the same orientation as before the replacement. This is
because of the convenience of cabling. Place the Oldham’s
coupling with the correct orientation, and engage the teeth.
(e) Fasten the pulse coder with the four M4 hexagonal socket
head bolts.
(f) Replace the packing on the motor cover mounting surface.
Reusing old packing cannot provide sufficient sealing
performance. Whenever taking off the motor cover, be sure
to replace the packing.
(g) Connect the cable of the pulse coder.
(h) Install the motor cover. Be careful not to catch the lead wires
of the pulse coder. After installing the motor cover, bolt the
cover.
ht
tp
://
w
w
w
.g
ef
an
uc
<2>-2 (Cable non-separation type)
(a) Remove the cannon connector of the pulse coder from the
motor terminal box.
(a)-1 Remove the M3 screw that retains the connector.
(a)-2 Shift the rubber packing, and remove the C-ring that
retains the insulator on the rear side (connection side)
of the connector to separate the connector housing
from the terminal section. Replace the rubber packing
with a new one.
(a)-3 Pull out the connector terminal section from the
terminal box toward the pulse coder.
(a)-4 Set the housing in the removed pulse coder (the pulse
coder to be replaced with a new one) in place, and hold
the housing with the C-ring.
(b) Cut the lead wires of the thermal switch. The wires should
be cut at the root of the crimp terminals where possible.
(c) Remove the four M4 hexagonal socket head bolts that retain
the pulse coder. Do not loosen the M3 bolts that retain the
pulse coder cover.
(d) Remove the pulse coder and Oldham’s coupling.
(e) Set a new pulse coder and new Oldham’s coupling in the
motor. Although the mounting orientation is not specified in
particular, it is recommended that the pulse coder be set with
the same orientation as before the replacement. This is
because of the convenience of cabling. Place the Oldham’s
coupling with the correct orientation, and engage the teeth.
(f) Fasten the pulse coder with the four M4 hexagonal socket
head bolts.
- 223 -
1. AC SERVO MOTOR
MAINTENANCE
TROUBLESHOOTING
B-65165E/02
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
ar
es
.co
m
/
(g) Replace the packing on the motor cover mounting surface.
Reusing old packing cannot provide sufficient sealing
performance. Whenever taking off the motor cover, be sure
to replace the packing.
(h) Install the connector in the cover in the reverse order of step
(a). Keying is provided for the connector insulator (the
insulating material around the terminals). So, perform
keying (phase) alignment when installing the connector.
(i) Connect the lead wires of the thermal switch. Peel off about
1 cm of the jacket from the cut end of each motor lead wire,
and tie the wire to the terminal of the pulse coder. Use of a
crimp terminal is recommended for connection. (In case of
an emergency, insulate both connection portions with
insulating tape.)
(j) Install the motor cover. Be careful to keep the lead wires of
the pulse coder clear of the motor cover. After installing the
motor cover, bolt the cover.
- 224 -
MOTOR MAINTENANCE
B-65165E/02
1.5
1. AC SERVO MOTOR
MAINTENANCE
SPECIFICATION NUMBERS OF REPLACEMENT PARTS
ar
es
.co
m
/
The following lists the ordering specification numbers for
maintenance:
(1) Ordering specifications of pulse coders
<1> Ordering specifications of pulse coders with no motor cover
Models α1 to α2, αM2 to αM2.5
A290-0371-T575 : αA64 (with Oldham’s coupling)
A290-0371-T577 : αI64 (with Oldham’s coupling)
A290-0371-T588 : αA1000 (with Oldham’s coupling)
Models α3 to α400, αM6 to αM40, αL, αC, α3HV to
α30HV, and αM6HV to αM30HV
an
uc
-s
p
• Cable separation type
A860-0360-V501: αA64
A860-0365-V501: αI64
A860-0370-V502: αA1000
A860-0360-V906: Cable assembly (common to αA64,
αI64, and αA1000)
A290-0501-V535: Oldham’s coupling (to be replaced
together with the pulse coder at a
time)
ht
tp
://
w
w
w
.g
ef
• Cable non-separation type (reference)
A860-0360-T201 : αA64
A860-0365-T101 : αI64
A860-0370-T201 : αA1000
A290-0501-V535: Oldham’s coupling (to be replaced
together with the pulse coder at a
time)
<2> Ordering specifications of pulse coders with a motor cover
Models α3 to α6, αM6 to αM9, αL6 to αL9, αC3 to αC6,
α3HV to α6HV, and αM6HV to αM9HV
A290-0121-T575 : αA64
A290-0121-T577 : αI64
A290-0121-T588 : αA1000
Models α12 to α40, αM22 to αM40, αL25 to αL50, αC12 to
αC22, α12HV to α30HV, and αM22HV to αM30HV
A290-0141-T575 : αA64
A290-0141-T577 : αI64
A290-0141-T588 : αA1000
- 225 -
1. AC SERVO MOTOR
MAINTENANCE
TROUBLESHOOTING
B-65165E/02
(3) Oldham’s coupling
A290-0501-V535
ar
es
.co
m
/
(2) Ordering specifications of motor covers
A290-0121-X035 : α3 to α6, αM6 to αM9, αL6 to αL9, αC3 to
αC6, α3HV to α6HV, αM6HV to αM9HV
A290-0141-X035 : α12 to α40, αM22 to αM40, αL25 to αL50,
αC12 to αC22, α12HV to α30HV, αM22HV
to αM30HV
-s
p
(4) Packing
A290-0511-X043 : α3 to α6, αM6 to αM9, αL6 to αL9, αC3 to
αC6, α3HV to α6HV, αM6HV to αM9HV
A290-0501-X043 : α12 to α40, αM22 to αM40, αL25 to αL50,
αC12 to αC22, α12HV to α30HV, αM22HV
to αM30HV
A290-0301-X008 : α65 to α150
ht
tp
://
w
w
w
.g
ef
an
uc
(5) Rubber packing and nylon band
A290-0651-X034 : Rubber packing
A6-NYB-T1
: Nylon band
- 226 -
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
ar
es
.co
m
SPINDLE MOTOR MAINTENANCE
/
MOTOR MAINTENANCE
B-65165E/02
2
2. SPINDLE MOTOR
MAINTENANCE
- 227 -
2. SPINDLE MOTOR
MAINTENANCE
2.1
TROUBLESHOOTING
B-65165E/02
PREVENTIVE MAINTENANCE
(1) Visual inspection
ar
es
.co
m
/
To maintain the original performance and reliability of the spindle
motor for a long time, it is necessary to inspect them as described
below.
The cooling air path is
clogged with dust.
Cutting fluid on the
motor surface.
Not rotating.
w
w
Fan motor
://
Unusual sound
Unusual sound from
the motor shaft bearing
Internal condition
of the terminal box
Cutting fluid in the
terminal box
tp
Motor shaft
bearing
ht
• Clean the motor surface.
• If the motor is splashed excessively with coolant, place a cover or take a
similar action.
If the fan motor can be rotated by the
Replace the fan motor.
hand,
If the fan motor cannot be rotated by the Remove foreign materials, if
hand,
any. Adjust its mounting
position by loosening the bolts
and tightening them again.
If unusual noise still remains,
replace the fan motor.
Remove foreign materials, if any. Adjust its mounting position by loosening
the bolts and tightening them again.
If unusual noise still remains, replace the fan motor.
Replace the shaft bearing, and check the shaft for centering accuracy. Also
check on the radial load. Before replacing the shaft bearing, contact your
FANUC service staff.
Check the terminal box lid and conduit packing.
If there is lot of fluid on the terminal box surface, protect the terminal box by
installing a shelter over it.
• Tighten the screw.
• Check whether there is abnormal vibration during motor rotation.
w
.g
Motor surface
uc
Cooling air path
Action
Check the following and take necessary actions:
• Base and installation
• Centering accuracy of directly coupled section
• Abnormal sound from motor shaft bearings (See "Motor shaft bearing"
below.)
• Vibration of or noise from the reducer or belts
• Amplifier failure
• Fan motor failure (See "Fan motor" below.)
Clean the stator vents and fan motor on a regular basis.
an
Symptom
There is unusual noise
or vibration.
The vibration
acceleration of the
motor exceeds 0.5 G at
the maximum speed.
ef
Inspection item
Noise or abnormal
vibration
-s
p
WARNING
Be careful not to be struck by electric shocks or
caught in gears or other mechanisms during
inspection. When taking corrective actions, keep the
entire machine switched off.
Loosen screw in the
terminal block
- 228 -
2. SPINDLE MOTOR
MAINTENANCE
MOTOR MAINTENANCE
B-65165E/02
ar
es
.co
m
/
(2) Checking the insulation between the winding and frame
Use a megohmmeter to measure the insulation resistance on 500
VDC. From the measurement result, determine whether the
insulation is acceptable or not according to the following criteria:
• More than 100 MΩ: Acceptable
• 10 to 100 MΩ: Deterioration has started. Although there is no
performance problem, periodic check is required.
• 1 to 10 MΩ: Deterioration is in an advanced state. Special
care must be taken. Periodic check is required.
• Less than 1 MΩ: Unacceptable. Replace the motor.
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
CAUTION
1 Before measuring insulation resistance, disconnect
the connection to the spindle amplifier module. If
insulation resistance is measured with the spindle
amplifier module connected, the spindle amplifier
module may be damaged.
2 During the measurement of insulation resistance,
applying voltage to the motor for a long time may
further deteriorate the insulation of the motor.
Therefore, the measurement of insulation resistance
should be performed in a minimum amount of time
where possible.
- 229 -
2. SPINDLE MOTOR
MAINTENANCE
TROUBLESHOOTING
B-65165E/02
an
uc
-s
p
ar
es
.co
m
/
(3) Check items for the coolant through spindle motor αT series and
αL series
<1> Check whether coolant is always leaking out from the drains
or notch of the rotary joint support housing. (See Fig. 2.)
<2> Check whether the vibration acceleration of the motor
turning at the maximum speed exceeds 0.5 G. (See Fig. 3.)
<3> Check whether coolant leaks out from the coolant joint of the
coupling. (See Fig. 4.)
<4> Check for backlash in the coupling.
ef
Coupling
Rotary joint support housing
ht
tp
://
w
w
w
.g
Fig. 1 Example of using the coolant through spindle motor
- 230 -
2. SPINDLE MOTOR
MAINTENANCE
MOTOR MAINTENANCE
B-65165E/02
Motor body
ar
es
.co
m
/
Rotary joint support housing
Pickup
Drain
Notch
Vibrometer
Spare drain
Fig. 2 Rotary joint support housing
d
φ
w
.g
φ
Concave type
ef
Convex type
an
uc
-s
p
Fig. 3 Measuring vibration acceleration
Coolant joint
ht
tp
://
w
w
Fig. 4 Example of a coolant joint
- 231 -
2. SPINDLE MOTOR
MAINTENANCE
2.2
TROUBLESHOOTING
B-65165E/02
ar
es
.co
m
(1) Parts of the terminal box (α, αP, αC, and αHV series)
/
MAINTENANCE PARTS
Terminal box assembly
Lid of terminal box
A290-0853-V410
A290-0853-T401
A290-0853-V410
A290-0854-T400
A290-0854-T401
A290-0854-V410
A290-0731-T420
A290-0731-T455
A290-0833-T400
A290-0860-T403
A290-0731-T421
A290-0731-V410
A290-0860-T401
A290-1040-X402
A290-0731-T456
A290-0833-T401
A290-0860-T404
A290-0731-V410
A290-1040-X402
A290-1040-X402
uc
A290-0860-T400
-s
p
A290-0853-T400
NOTE
1 For example, drawing number A06B-0856-B100
ends with B0, and A06B-0856-B130 ends with
B3.
2 The above table may not apply to motors of which
motor drawing number ends with B9. Contact
your FANUC service representative.
3 The above table may not apply to maintenance parts
of high-speed models.
w
.g
ht
tp
://
w
w
When the motor drawing No.
ends with B 3 (Note 1)
A290-0850-T400
ef
α1, α1.5,
αC1, αC1.5
α2, α3,
αC2, αC3
α6 to α15
αP8 to αP22
α6HV to α15HV
αC6 to αC15
α18, α22
α18HV, α22HV
αC18, αC22
α30, α40
α30HV, α40HV
αP30 to αP50
αP60
α60HV
When the motor drawing No. ends
with B 0 or B 9 (Note 1)
an
Model
- 232 -
2. SPINDLE MOTOR
MAINTENANCE
MOTOR MAINTENANCE
B-65165E/02
(2) Terminal box drawing numbers (αT series)
Terminal box assembly
Lid of terminal box
/
Motor drawing No.(Note 4)
A06B-0871-B927
A06B-0869-B927
A06B-0853-B927
A06B-0854-B927
A06B-0855-B927
A06B-0857-B927, B928
A06B-0859-B927, B928
A290-0853-T408
A290-0853-V410
A290-0854-T408
A290-0854-V410
A290-0731-T457
A290-0731-V410
ar
es
.co
m
Model name
αT1.5/15000
αT2/15000
αT3/12000
αT6/12000
αT8/12000
αT15/10000
αT22/10000
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
NOTE
4 The above table may not apply to the motors other
than the drawing numbers listed in the above table.
Contact your FANUC service representative.
- 233 -
2. SPINDLE MOTOR
MAINTENANCE
TROUBLESHOOTING
B-65165E/02
(3) Fan motor parts (α, αP, αC, and αHV series)
αP50, αP60
A290-0853-X501
A290-0854-X501
A290-0856-X501
A290-0731-T510(Note 5)
A290-0731-T511(Note 5)
A290-0832-T500(Note 5)
A290-0832-T501(Note 5)
Backward
A90L-0001-0444/FS
Forward
A90L-0001-0444/R
A90L-0001-0444/F
A90L-0001-0318/R
A90L-0001-0318/F
A90L-0001-0319/R
A90L-0001-0319/F
A90L-0001-0457/R
A90L-0001-0457/F
A90L-0001-0458/RS
A90L-0001-0458/FS
A90L-0001-0458/R
A90L-0001-0458/F
A90L-0001-0399/R
A90L-0001-0399/F
A90L-0001-0400/R
A90L-0001-0400/F
Backward
Forward
Backward
Forward
Backward
Forward
Backward
Forward
Backward
Forward
Backward
Forward
Backward
Forward
Backward
Forward
α12HV, α15HV
A290-0856-X501
α18HV, α22HV
A290-0856-X501
α30HV, α40HV
A290-0780-T510(Note 4)
A290-0780-T511(Note 4)
A290-0883-T500(Note 4)
A290-0883-T501(Note 4)
an
ef
w
.g
/
A90L-0001-0444/RS
uc
A290-0854-X501
NOTE
5 These drawing numbers include fan motors.
6 The above table may not apply to motors of which
motor drawing number ends with B9. Contact
your FANUC service representative.
7 The above table may not apply to maintenance parts
of high-speed models.
ht
tp
://
w
w
Air flow direction
Backward
Forward
Backward
Forward
Backward
Forward
A290-0856-X501
α6HV, α8HV
α60HV
Fan motor
A90L-0001-0491/R
A90L-0001-0491/F
A90L-0001-0442/R
A90L-0001-0442/F
A90L-0001-0443/R
A90L-0001-0443/F
ar
es
.co
m
Fan cover
A290-0850-T500(Note 5)
A290-0850-T501(Note 5)
-s
p
Model
α1, α1.5
αC1, αC1.5
α2, α3
αC2, αC3
α6, α8, αP8
αC6, αC8
α12, α15, αP12,
αP15
αC12, αC15,
αP18, αP22
α18, α22
αC18, αC22
α30, α40
αP30, αP40
- 234 -
2. SPINDLE MOTOR
MAINTENANCE
MOTOR MAINTENANCE
B-65165E/02
(4) Fan motor parts (αT series)
Fan cover
Fan motor
Fan base
A290-0850-T504(Note 8)
A90L-0001-0491/RL
A290-0853-X501
A90L-0001-0442/RL
A290-0853-X507
A290-0854-X501
A90L-0001-0443/RL
A290-0854-X507
A290-0856-X501
A90L-0001-0444/RL
A290-0856-X504
/
αT1.5/15000
αT2/15000
αT3/12000
αT6/12000
αT8/12000
αT15/10000
αT22/10000
Motor drawing
No.(Note 9)
A06B-0871-B927
A06B-0869-B927
A06B-0853-B927
A06B-0854-B927
A06B-0855-B927
A06B-0857-B927, B928
A06B-0859-B927, B928
ar
es
.co
m
Model name
ht
tp
://
w
w
w
.g
ef
an
uc
-s
p
NOTE
8 These drawing numbers include fan motors.
9 The above table may not apply to the motors other
than the drawing numbers listed in the above table.
Contact your FANUC service representative.
- 235 -
2. SPINDLE MOTOR
MAINTENANCE
2.3
TROUBLESHOOTING
B-65165E/02
PERMISSIBLE RADIAL LOAD
ar
es
.co
m
/
Use motor output axes under the permissible radial load listed below or
less:
Permissible radial load
Center of output
Output axis end
axis
294 N (30 kgf)
323 N (33 kgf)
392 N (40 kgf)
441 N (45 kgf)
882 N (90 kgf)
980 N (100 kgf)
882 N (90 kgf)
999 N (102 kgf)
1470 N (150 kgf)
1607 N (164 kgf)
1960 N (200 kgf)
2205 N (225 kgf)
2940 N (300 kgf)
3371 N (344 kgf)
2940 N (300 kgf)
3410 N (348 kgf)
4410 N (450 kgf)
4988 N (509 kgf)
5390 N (550 kgf)
6134 N (626 kgf)
10780 N (1100 kgf)
392 N (40 kgf)
490 N (50 kgf)
980 N (100 kgf)
1470 N (150 kgf)
1960 N (200 kgf)
12299 N (1255 kgf)
19600 N (2000 kgf)
441 N (45 kgf)
558 N (57 kgf)
1068 N (109 kgf)
1656 N (169 kgf)
2244 N (229 kgf)
2450 N (250 kgf)
2842 N (290 kgf)
2940 N (300 kgf)
3332 N (340 kgf)
5390 N (550 kgf)
6134 N (626 kgf)
NOTE
1 When using a belt, adjust the tension of the belt so
that the permissible value listed above is not
exceeded.
2 When the belt tension center is positioned beyond
the end of an output axis, the permissible load
becomes smaller than that at the end of the output
axis.
ht
tp
://
w
w
w
.g
ef
an
uc
〈0.5
α1, αC1
α1.5, αC1.5
α2, αC2
α3, αC3
α6, α6HV, αC6
α8, αP8, α8HV, αC8
α12, α15, αP12, αP15
α12HV, α15HV, αC12, αC15
α18, α22, αP18, αP22
α18HV, α22HV, αC18, αC22
α30, α40, αP30, αP40
α30HV, α40HV
αP50
αP60, α60HV
α1/15000
α2/15000
α3/12000
α6/12000
α8/8000, αP8/8000
α12/8000, α15/8000
αP12/8000, αP15/8000
α18/8000, α22/8000
αP18/8000, αP22/8000
α30/8000, αP30/8000, αP40/8000
-s
p
Model
- 236 -
INDEX
B-65165E/02
Alarm code 12 150, 171
α (HV) series spindle amplifier module (SPM-HV) 30
Alarm code 13 151
α Series and α (HV) Series Spindle Amplifier Module 144
Alarm code 15 151
α series power supply modules 7
Alarm code 16 121, 151
α series spindle amplifier module (SPM) 29
Alarm code 17 123
α series spindle amplifier modules 14
Alarm code 18 123
αC series spindle amplifier module (SPMC) 30
Alarm Code 2 173
αC Series Spindle Amplifier Module 171
Alarm code 2 125
150 mm Width Module (with the Connector Module) 182
Alarm code 24 152
150 mm Width Module (without the Connector Module) 180
Alarm code 25 152
200-V input series 10
Alarm code 26 122, 153
300-mm Wide Module (with the Connector Module) 190
Alarm code 27 155
-s
p
uc
300-mm Wide Module (without the Connector Module) 185
ar
es
.co
m
α (HV) series power supply modules 9
Alarm code 28 156
Alarm code 29 157
an
400-V input series 13
Alarm Code 3 173
60/90 mm Width Modules 178
w
.g
A specified speed cannot be obtained. 52
ef
Alarm code 30 158
[A]
/
INDEX
Alarm code 31 158
Alarm code 32 159
Alarm code 33 159
display) 128
Alarm code 34 159
Alarm code 35 160, 172
Address descriptions and initial values (SPM) 74
Alarm code 36 122, 160
Address descriptions and initial values (SPMC) 75
Alarm code 37 161
Alarm code 01 116, 120, 145
Alarm Code 39 162
Alarm code 02 117, 120, 146
Alarm Code 4 174
Alarm code 03 117, 120, 147
Alarm code 4 125
Alarm code 04 118, 121, 147
Alarm code 40 163
Alarm code 05 118, 121
Alarm code 41 164
Alarm code 06 118, 121
Alarm code 42 165
Alarm code 07 119, 122, 148
Alarm code 43 165
Alarm code 08 123
Alarm code 44 165
Alarm code 09 148
Alarm code 46 122, 165
Alarm Code 1 173
Alarm code 47 166
Alarm code 11 149
Alarm code 49 167
ht
tp
w
w
AC SERVO MOTOR MAINTENANCE 209
://
Abnormal Current Alarms (8, 9, A, b, C, d, and E in the LED
INDEX
B-65165E/02
Checking The Feedback Signal Waveform 58
Alarm code 5 126
Checking The Power Supply Voltages 35
Alarm code 50 167
Checking The STATUS Display 46
Alarm code 51 167
Checking The Status Leds 36
Alarm code 54 168
Checking The Voltage And Capacity Of The Power 25
Alarm code 55 168
CONFIGURATIONS 4, 5
Alarm code 56 169
CONFIRMATION OF THE OPERATION 32
Alarm code 57 169
Connecting a Battery to Multiple SVMs 88
Alarm code 58 169
Connecting A Protective Ground 26
Alarm code 59 170
CONNECTING THE POWER 25
Alarm code 6 126
Control Power Supply Undervoltage Alarm (2 in the LED
Alarm code 7 126
display) 131
Alarm code 8 127
Current Conversion Error Alarm 131
Alarm code A0 124
Cutting power weakens or acceleration/deceleration slows
ar
es
.co
m
-s
p
down. 54
uc
Alarm code A1 124
Alarm code A2 124
[D]
Alarm codes 19 and 20 152
an
DAILY INSPECTION OF AC SERVO MOTORS 211
Alarm codes 52 and 53 168
Data numbers 80
Alarm codes A, A0 to A4, and other Ax (x for representing an
ef
arbitrary number) 144
w
.g
ALARM NUMBERS AND BRIEF DESCRIPTIONS 98
DC Link Undervoltage Alarm (5 in the LED display) 131
Diagnosis Screen 135
Alarms Related to Pulse Coder and Separate Serial Detector
139
[E]
An overshoot or hunting occurs. 53
Example of monitoring data 83
w
w
Attaching and Detaching Connectors 92
[F]
[B]
Fan Stopped Alarm (1 in the LED display) 131
BATTERY FOR THE ABSOLUTE PULSE CODER 85
://
Feedback Disconnected Alarm 137
FOR SERIES 0-C 112
[C]
tp
FOR SERIES 15 108
FOR SERIES 15i 102
Check board connection 68
FOR SERIES 16, 18, 20, 21 105
Check Pin Board 41
FOR SERIES 16i, 18i, 20i, 21i, AND Power Mate i 99
ht
CASE DISASSEMBLY 178
Check Terminal On The Printed-circuit Board 34
Check terminal output signals 69
[H]
Checking For What Keeps The Mcc From Being Switched On
High-resolution magnetic pulse coder 63
39
/
Alarm Code 5 174
INDEX
B-81224EN/01
HOW TO REPLACE THE FUSES AND PRINTED
Power Supply Module (PSMV) 119
CIRCUIT BOARDS 175
POWER-FAILURE BACKUP MODULE 173
[I]
ar
es
.co
m
PREVENTIVE MAINTENANCE 228
/
Power-Failure Backup Module 22, 202
INITIALIZING SERVO PARAMETERS 31
Principles in outputting the internal data of the serial spindle
Installing a Special Lithium Battery in the SVM (Method 1)
76
86
PSM, PSM-HV 34
Invalid Servo Parameter Setting Alarm 138
PSM, PSM-HV, and PSMV-HV 36
IPM Alarms (8., 9., A., b., C., d., and E in the LED display;
PSMR 37
note these codes are displayed simultaneously with a period.)
PSMV-HV 35
130
[R]
-s
p
[M]
RECEIVING AND KEEPING AC SERVO MOTORS 210
M sensor 60
REPLACING FUSES 196
MAINTENANCE PARTS 232
Replacing the Battery 91
uc
Major characteristics 71
REPLACING THE PULSE CODER 216
MAJOR COMPONENTS 7
Replacing the SPM Program ROM and Spindle Sensor
MZ and BZ sensors 61
an
Module 203
ef
MZ sensor for α 0.5 (A06B-0866-B390) (old specification) 62
Observation method 72
w
.g
[O]
[S]
Selecting The Ground Fault Interrupter That Matches The
Leakage Current 26
Observing Data Using the Spindle Check Board 71
Servo Adjustment Screen 133
Other Alarms 142
SERVO AMPLIFIER MODULE 40, 128
OTHER COMPONENTS 203
w
w
Servo Amplifier Module 28, 199
Servo Amplifier Modules 10
Overload Alarm (Soft Thermal, OVC) 136
Servo Check Board 48
OVERVIEW 3, 97
SERVO SOFTWARE 133
Overview 71
SETTING THE PRINTED-CIRCUIT BOARD 27
://
Overheat Alarm 138
tp
SPECIFICATION NUMBERS OF REPLACEMENT PARTS
225
[P]
Specifying data to be monitored 73
ht
PERIODIC INSPECTION OF AC SERVO MOTORS 213
PERIODIC MAINTENANCE OF SERVO AMPLIFIER 84
SPINDLE AMPLIFIER MODULE 49, 144
PERMISSIBLE RADIAL LOAD 236
Spindle Amplifier Module 29, 200
POWER SUPPLY MODULE 33, 116
Spindle Amplifier Modules 14
Power Supply Module 7, 27, 196
Spindle Check Board 67
Power Supply Module (PSM, PSM-HV) 116
Spindle check board specifications 67
Power Supply Module (PSMR) 125
SPINDLE MOTOR MAINTENANCE 227
INDEX
B-65165E/02
START-UP PROCEDURE 23
START-UP PROCEDURE (OVERVIEW) 24
/
STATUS Display 50
ar
es
.co
m
Status Error Indication Function 55
[T]
The motor does not turn. 52
The PIL LED (power ON indicator) Is Off. 38
The PIL LED (power-on indicator) is off. 51
The STATUS display is blinking with "--." 51
TROUBLESHOOTING AND ACTION 115
-s
p
Troubleshooting at Startup 51
Using a Battery Case (A06B-6050-K060) (Method 2) 87
an
[V]
uc
[U]
ef
VRDY-OFF Alarm Indicated on the CNC Screen 47
[W]
w
.g
When cutting is not performed, the spindle vibrates, making
ht
tp
://
w
w
noise. 53
Jun., 2000
Apr., 1994
Date
02
01
Edition
://
Revision Record
Total Revision
w
.g
Contents
w
w
Edition
Date
/
Contents
ar
es
.co
m
-s
p
uc
an
ef
FANUC SERVO MOTOR α series MAINTENANCE MANUAL (B-65165E)
tp
ht
m
/
es
.c o
ar
No part of this manual may be
reproduced in any form.
·
All specifications and designs
are subject to change without
notice.
ht
tp
://
w
w
w
.g
ef
a
nu
csp
·
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising