User manual
Always there to help you
Register your product and get support at
www.philips.com/support
Question?
Contact
Philips
User manual
AZ127
The difference between V1.0/V2.0 version and V3.0 version user manual is as
following:
V1.0/V2.0: Fixed power cord
V3.0: Detachable power cord
Contents
1Important
2
2 Your CD Soundmachine
3
Introduction3
What's in the box
3
Overview of the main unit
4
3 Get started
6
6
7
7
4Play
8
8
8
8
9
Connect power
Turn on
Turn off
Play a CD
Play from an external device
Play tape
Tune to FM radio stations
5 Play options
Control play
Program tracks
Adjust sound
10
10
10
10
6 Product information
11
Specifications
11
Maintenance11
7Troubleshooting
13
8Notice
14
EN
1
1Important
•
•
•
•
•
•
•
•
•
•
•
2
Read these instructions.
Follow all instructions.
Do not block any ventilation openings.
Install in accordance with the
manufacturer's instructions.
Do not install near any heat sources such
as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that
produce heat.
Protect the power cord from being
walked on or pinched, particularly at plugs,
convenience receptacles, and the point
where they exit from the unit.
Only use attachments/accessories specified
by the manufacturer.
Unplug this unit during lightning storms or
when unused for long periods of time.
Recording is permissible insofar as
copyright or other rights of third parties
are not infringed upon.
Refer all servicing to qualified service
personnel. Servicing is required when the
unit has been damaged in any way, such
as power-supply cord or plug is damaged,
liquid has been spilled or objects have
fallen into the apparatus, the unit has been
exposed to rain or moisture, does not
operate normally, or has been dropped.
Battery usage CAUTION – To prevent
battery leakage which may result in bodily
injury, property damage, or damage to the
unit:
• Install all batteries correctly, + and - as
marked on the unit.
• Do not mix batteries (old and new or
carbon and alkaline, etc.).
• Remove batteries when the unit is not
used for a long time.
Batteries (battery pack or batteries
installed) shall not be exposed to excessive
heat such as sunshine, fire or the like.
EN
•
•
•
•
•
CAUTION: Danger of explosion if battery
is incorrectly replaced. Replace only with
the same or equivalent type.
The unit shall not be exposed to dripping
or splashing.
Do not place any sources of danger on
the unit (e.g. liquid filled objects, lighted
candles).
Where the MAINS plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
The CD Soundmachine can be used in
tropical climate zone.
Warning
•• Never remove the casing of this apparatus.
•• Never place this apparatus on other electrical
equipment.
•• Never look into the laser beam inside this apparatus.
Caution
•• Use of controls or adjustments or performance of
procedures other than herein may result in hazardous
radiation exposure or other unsafe operation.
2 Your CD
Soundmachine
Introduction
With this CD Soundmachine, you can:
• listen to FM radio;
• enjoy audio from discs, tapes, and other
external audio devices;
• program the play sequence of tracks.
The unit offers you Dynamic Bass Boost (DBB)
to enrich sound.
What's in the box
Check and identify the contents of the package:
• CD sound machine
• Power plug
• Short User Manual
• Safety sheet
EN
3
Overview of the main unit
e
a
f
g
b
h
c
i
d
j
k
m
l
n
o
p
a DBB
• Turn dynamic bass boost on/off.
e OPEN•CLOSE
• Open or close the disc compartment.
b REPEAT
• Play a track or all tracks repeatedly.
f Tape controls
•
Start tape play.
•
/
Fast rewind or fast forward the tape.
Stop the tape play or open the tape
door.
•
Pause tape play or pause recording.
c
d
4
/
• Start or pause play.
• Turn on/off the unit.
• Press to wake up the unit from
standby mode.
EN
g SHUFFLE
• Play tracks randomly.
h PROG
• Program the play sequence of tracks.
i
/
• Skip to the previous or next track.
• Search within a track.
j Display panel
• Display current status.
k FM antenna
• Improve FM reception.
l TUNING +/• Tune to FM radio stations.
m VOL +/• Adjust volume
n Source selector
• Select a source.
o AUDIO-IN
• Connect an external audio device.
p AC MAINS ~
EN
5
3 Get started
Caution
•• Use of controls or adjustments or performance of
procedures other than herein may result in hazardous
radiation exposure or other unsafe operation.
Always follow the instructions in this chapter in
sequence.
If you contact Philips, you will be asked for the
model and serial number of your apparatus. The
model number and serial number are on the
bottom of your apparatus. Write the numbers
here:
Model No. __________________________
Serial No. ___________________________
Connect power
The unit can be powered by either AC power
or batteries.
Option 1: AC power
Warning
•• Risk of product damage! Make sure that the power
supply voltage corresponds to the voltage printed on
the back or the underside of the unit.
•• Risk of electric shock! When you disconnect the AC
power, always pull the plug from the socket. Never pull
the cord.
Connect the AC power cord too:
• the wall socket
• the AC MAINS ~ socket of the CD sound
machine
Tip
•• To save energy, turn the unit off after use.
6
EN
AC~MAINS
Option 2: Battery power
Caution
•• Batteries contain chemical substances, so they should
be disposed of properly.
Note
•• Batteries are not supplied with the accessories.
1
2
3
Open the battery compartment.
Insert 6 batteries (type: 1.5V R14/UM2/C
CELL) with correct polarity (+/-) as
indicated.
Close the battery compartment.
Turn on
Press .
»» When the source selector is in
the AUDIO-IN/CD position, is
displayed.
Switch to standby mode
• The unit switches to standby mode
automatically when there is no audio
detected for over 15 minutes.
• In CD/FM/AUDIO IN mode, press to
wake up the unit from standby mode.
Turn off
Press
again.
EN
7
4Play
Play from an external device
You can also listen to an external audio device
through this unit.
1
Play a CD
2
Note
•• You cannot play CDs encoded with copyright
protection technologies.
You can play commercially available audio CDs:
• CD-Recordables (CD-R)
• CD-Rewritables (CD-RW)
1
2
3
4
Switch the source selector to AUDIO-IN/
CD.
Open the CD compartment.
3
Connect an audio cable (3.5mm, not
supplied) to:
• the AUDIO-IN socket on the unit.
• the headphone socket on an external
device.
Play the external device (see the device's
user manual).
Note
•• The AUDIO-IN socket is not for headphones.
•• The display panel lights off when the unit plays from the
external device.
Insert a CD with the printed side facing up
and close the CD lid gently.
»» The total number of tracks displays.
Press
»» [
Switch the source selector to AUDIO-IN/
CD.
to start play.
] displays.
•
•
To select a track,press
To pause CD play, press
»» [ ] flashes.
•
•
To resume CD play, press
To stop CD play, press .
/
.
.
Audio-in
again.
Play tape
Note
•• The unit will turns off automatically after an elapsed
time of inactivity at tape mode.
1
2
8
EN
Slide the source selector to TAPE.
»» The unit turns on automatically.
Press
door.
on main unit to open the tape
3
4
Load the tape with the open side upward
and the full spool to the right.
Press on main unit to start play.
• To pause/resume play, press on main
unit .
• To rewind or fast-forward, press
/
on main unit .
• To stop play, press
.
»» The unit turns off automatically.
Note
•• In playback mode, cassette will be stopped
automatically when playback reaches the end.
Tune to FM radio stations
Note
•• For optimal reception, fully extend and adjust the
position of the FM antenna.
1
2
3
Switch the source selector to FM.
Rotate TUNING to select a station.
Repeat step 2 to tune to more stations.
EN
9
5 Play options
Program tracks
In CD mode, you can program a maximum of
20 tracks.
Control play
In CD mode, you can control play through the
following operations.
/
PROG
+VOLUMEREPEAT
SHUFFLE
Press:skip to the previous/next
track
Hold:search within play, then
release to resume play.
Start or pause play.
Stop play.
Program tracks.
Adjust volume.
[ ]: Play the current track
repeatedly.
[
]: Play all tracks
repeatedly.
[
]: Repeat all tracks
randomly.
To return to normal play, press
REPEAT repeatedly until the
repeat icons disappear.
[
]: Play tracks randomly.
To return to normal play, press
SHUFFLE repeatedly until the
shuffle icon disappear.
Tip
•• Only [
]] and [
] can be selected when you
play the programmed tracks.
10
EN
1
2
3
4
5
Press
to stop playback.
Press PROG to activate the program
mode.
»» [PROG] (program) begin to blink.
Press
/
to select a track number,
then press PROG to confirm.
Repeat steps 3 to program more tracks.
Press
to play the programmed tracks.
»» During play, [PROG] (program) is
displayed.
• To erase the program, press twice.
• To review the program, when playback
is stopped,press and hold PROG for 2
seconds.
Adjust sound
During play, you can adjust volume and select
the sound effects.
Key
+VOLUMEDBB
Function
Increase or decrease volume.
Turn dynamic bass
enhancement on or off.
6Product
information
Note
Tape deck
Frequency response
- Normal tape (type I)
Signal-to-noise ratio
- Normal tape (type I)
Wow and flutter
125 - 8000 Hz
(8 dB)
35 dBA
≤ 0.4% DIN
•• Product information is subject to change without prior
notice.
General
Specifications
Amplifier
Rated Output Power
Frequency Response
Signal to Noise Ratio
Total Harmonic Distortion
Audio-in Input
2 W RMS
125 -16000 Hz,
-3dB
>55 dBA
<1 %
650 mV RMS
220-240V~, 50/60 Hz;
9 V, 6 x 1.5 V type:
R14/UM2/C CELL
10 W
<0.5 W
300 x 134 x 240 mm
1.5 kg
Maintenance
Disc
Laser Type
Disc Diameter
Support Disc
Audio DAC
Total Harmonic
Distortion
Frequency Response
S/N Ratio
Power supply
- AC Power
- Battery
Operation Power
Consumption
Standby Power
Consumption
Dimensions
- Main Unit (W x H
x D)
Weight (Main Unit)
Semiconductor
12cm/8cm
CD-DA, CD-R, CD-RW
24Bits / 44.1kHz
<1%
125 -16000 Hz, -3dB
>55 dBA
Clean the cabinet
• Use a soft cloth slightly moistened with
a mild detergent solution. Do not use a
solution containing alcohol, spirits, ammonia
or abrasives.
Clean discs
• When a disc becomes dirty, clean it with
a cleaning cloth. Wipe the disc from the
centre out.
Tuner
Tuning Range
Total Harmonic Distortion
Signal to Noise Ratio
87.5 - 108MHz
<3%
>50 dBA
•
Do not use solvents such as benzene,
thinner, commercially available cleaners,
or antistatic spray intended for analogue
records.
EN
11
Clean the disc lens
• After prolonged use, dirt or dust may
accumulate at the disc lens. To ensure good
play quality, clean the disc lens with Philips
CD lens cleaner or any commercially
available cleaner. Follow the instructions
supplied with cleaner.
Clean the heads and the tape paths
• To ensure good recording and play quality,
clean the heads A, the capstan(s) B, and
pressure roller(s) C after every 50 hours
of tape operation.
• Use a cotton swab slightly moistened with
cleaning fluid or alcohol.
•
You can also clean the heads by playing a
cleaning tape once.
Demagnetise the heads
• Use a demagnetising tape available at your
dealer.
12
EN
7Troubleshooting
Warning
Poor radio reception
•• Increase the distance between the unit and
your TV or VCR.
•• Fully extend the FM antenna.
•• Never remove the casing of this device.
To keep the warranty valid, never try to repair
the system yourself.
If you encounter problems when using this
device, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips Web page (www.
philips.com/support). When you contact Philips,
make sure that the device is nearby and the
model number and serial number are available.
No power
• Ensure that the Mains cord is connected
securely.
• Ensure that there is power at the AC
Mains.
• Ensure that the batteries are inserted
correctly.
No sound or poor sound
•• Adjust the volume.
No response from the unit
•• Disconnect and reconnect the AC power
plug, then turn on the system again.
•• As a power-saving feature, the unit
switches off automatically 15 minutes after
track play reaches the end and no control
is operated.
Poor cassette sound quality
• Ensure that heads in the cassette holder
are clean.
• Ensure that a NORMAL (IECI) cassette
tape is used for record.
Cassette does not work for record
• Ensure that cassette tabs are not broken.
No disc detected
•• Insert a disc.
•• Check if the disc is inserted upside down.
•• Wait until the moisture condensation at
the lens has cleared.
•• Replace or clean the disc.
•• Use a finalized CD or correct format disc.
EN
13
8Notice
This apparatus includes these labels:
This product complies with the radio
interference requirements of the European
Community.
Any changes or modifications made to this
device that are not expressly approved by
WOOX Innovations may void the user’s
authority to operate the equipment.
Disposal of your old product
Class II equipment symbol
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
The making of unauthorized copies of copyprotected material, including computer
programs, files, broadcasts and sound
recordings, may be an infringement of
copyrights and constitute a criminal offence.
This equipment should not be used for such
purposes.
This symbol on a product means that the
product is covered by European Directive
2012/19/EU. Inform yourself about the local
separate collection system for electrical and
electronic products. Follow local rules and never
dispose of the product with normal household
waste. Correct disposal of old products
helps prevent negative consequences for the
environment and human health.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
paper pulp (buffer) and polyethylene (bags,
protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
14
EN
This symbol indicates that the apparatus has a
double insulation system.
Note
•• The type plate is located on the bottom of the
apparatus.
Specifications are subject to change without notice
2014 © WOOX Innovations Limited. All rights reserved.
Philips and the Philips’ Shield Emblem are registered trademarks of Koninklijke Philips N.V.
and are used by WOOX Innovations Limited under license from Koninklijke Philips N.V.
AZ127_12_UM_V3.0
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising