Milesight-Troubleshooting P2P on Mobile APP

Milesight-Troubleshooting P2P on Mobile APP
Milesight-Troubleshooting
P2P on Mobile APP
M-VMS Version
V3.0.0.12(IOS)、V3.0.0.4(Android)
M-Sight Version
V2.1.0.19(IOS)、V2.1.0.20(Android)
Update
2017.4.18
1. P2P
A peer-to-peer (P2P) network is a type of decentralized and distributed network
architecture in which individual nodes in the network (called "peers") act as both suppliers
and consumers of resources, in contrast to centralized client – server model where client
nodes request access to resources provided by central servers. Networks in which all
computers have equal status are called peer-to-peer or P2P networks.
In a peer-to-peer network, tasks (such as searching for files or streaming audio/video)
are shared amongst multiple interconnected peers which each make a portion of their
resources (such as processing power, disk storage or network bandwidth) directly available
to other network participants, with no need for centralized coordination by servers.
A peer-to-peer (P2P) network
A network based on the client-server model
With the P2P enabled on NVR and Network Camera, you can add the NVR and Network
Camera to APP and view the live video over WLAN remotely without doing any port
forwarding on the router.
Guide for P2P activation with MAC address:
1
2. How to Use P2P on M-VMS
You can use P2P freely on Milesight NVR after the following settings:
2.1 Activate the NVR
If your NVR is:
MS-Nxxxx-UH/UPH and the firmware version is 71.7.0.5-r13 or above;
MS-Nxxxx-UT/UPT and the firmware version is 72.7.0.5-r13 or above;
You need to provide the MAC address to Milesight to activate the NVR first. If not, just
skip this step to 2.2.2.
MAC on the back of NVR:
2
Figure 2-1
MAC on the monitor:
Right click on the live view and choose“Menu”->“Status”->“Network Status”, you
will see the image as below, then you can find the MAC of the LAN1:
Figure 2-2
Note:
The MAC address you provide to Milesight must be the LAN1 MAC .
MAC on the web:
Enter the web page of NVR ->“Status”->“System”->“Network Status”, you will see the
image as below, then you can find the MAC address:
3
Figure 2-3
2.2 Settings on NVR
2.2.1 Firmware version is 7X.7.0.5-r18 or above:
Way 1: Enable on the monitor
Right click on the live view and choose“Menu”->“System”->“Network”->“P2P”,
you will see the image as below; Then choose “Enable” and click “Apply” to enable P2P.
Figure 2-4
If failed to apply this setting, please check these tips:
Marked Words
Description
Network Error.
Check the network condition.
Register failed.
MAC address doesn’t register the P2P.
Unknown Error.
Need to contact with Milesight Support.
Way 2: Enable on the web
Enter the web page of NVR ->“Settings”->“System”->“Network Settings”->“P2P”.
4
Details are the same as on the monitor.
Figure 2-5
If failed to save, please check these tips:
Marked Words
Description
Network Error.
Check the network condition.
Register failed.
MAC address doesn’t register the P2P.
Unknown Error.
Need to contact with Milesight Support.
Note:
P2P is a WLAN-required function, so you need to make sure that the network of Default
Gateway and Preferred DNS Server are available.
2.2.2: Firmware version is between 7X.7.0.5-r13 and 7X.7.0.5-r17
Way 1: Enable on the monitor
Right click on the live view and choose“Menu”->“System”->“Network”->“P2P”,
you will see the image as below;
Figure 2-6
5
1. Choose“Enable”from the drop-down list of“P2P”;
2. Fill in your Company Name or your Individual Name in the“Company Name”;
3. Fill in your Email address in the“Email”for activation;
4. Apply the settings.
Way 2: Enable on the web
Enter the web page of NVR ->“Settings”->“System”->“Network Settings”->“P2P”.
Details are the same as on the monitor.
Figure 2-7
Note:
P2P is a WLAN-required function, so you need to make sure that the network of Default
Gateway and Preferred DNS Server are available.
2.3 Settings on M-VMS
Step 1: Open the M-VMS, and click on these icons to add device:
->
;
Step 2: Choose “IP/Server” as “Register Type”;
Figure 2-8
6
->
Figure 2-9
Step 3: Add S/N or MAC
The S/N is on the back of NVR;
Figure 2-10
There are two ways to add the S/N or MAC;
Figure 2-11
Figure 2-12
Way 1: Input manually after touching area ①;
7
Figure 2-13
Way 2: Automatically input by scanning bar code/ QR code after touching icon ②;
Figure 2-14
Step 4: Input the NVR name, the user name and the password to finish adding the device.
8
Figure 2-15
Note:
Only V3.0.0.10(IOS)/V3.0.0.2(Android) or above of M-VMS support to add NVR via MAC.
2.4 Device management
After adding the NVR by P2P, you can manage the NVR by touching ”Device Manager”. If
you want to view the live image of your NVR, touch the“Device Name”; If you want to edit
the NVR, touch the ”Information” icon;
Figure 2-16
If you want to delete the NVR, you can slide left on the“Device Name”column and then
select“Delete”.
Figure 2-17
9
Note:
NVR P2P function can be only supported when the version is higher than XX.X.X.52
(included), if your NVR version is below 52, please upgrade first.
3. How to Use P2P on M-Sight
You can use P2P freely on Milesight network Camera after the following settings:
3.1 Activate the Network Camera
Provide the MAC address to Milesight to activate the network Camera first.
MAC on the housing of network Camera
Figure 3-1
MAC on the web:
Enter the web page of Network Camera ->“Configuration”->“System”, you will see the
image as below, then you can find the MAC address:
Figure 3-2
Note:
Once activated, the Network Camera must be restarted before using the P2P function.
If the firmware version of network camera is XX.6.0.54 or above, there is a QR code
10
showing up in the “System” page after restarting device. You can add the camera on APP
by scanning this QR code.
Figure 3-3
3.2 Settings on M-Sight
Step 1: Open the M-Sight, and click on these icons to add device:
->
->
;
Step 2: Choose “P2P” as “Type”:
Figure 3-3
Step 3: Add MAC
There are two ways to add MAC:
11
->
Figure 3-4
Way 1: Input manually after touching area ①;
Figure 3-5
Way 2: Automatically input by scanning bar code/ QR code after touching icon ②;
Figure 3-6
Step 4: Input the network Camera name, the user name and the password to finish adding
device.
12
3.3 Device management
After adding the network Camera via P2P, you can manage the Network Camera by
touching ”Device Manager”. If you want to edit the network Camera, touch the area ①;
Figure 3-7
If you want to view the live video of your network Camera, touch the “Play” ;
Figure 3-8
If you want to delete the network Camera, you can slide left on the“Device Name”
column and then select“Delete”.
13
Figure 3-9
-END-
14
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising