SUO IM 990-5268 MN01 EN.fm
Installation Guide Smart-UPS™On-Line
SRT2200/SRT3000 Tower/Rack-Mount 2U
Important Safety Messages
Read the instructions carefully to become familiar with the equipment before attempting to install, operate, service or
maintain the UPS. The following special messages may appear throughout this manual or on the equipment to warn of
potential hazards or to call attention to information that clarifies or simplifies a procedure.
The addition of this symbol to a Danger or Warning product safety label indicates that an electrical hazard
exists which will result in personal injury if the instructions are not followed.
The addition of this symbol to a Warning or Caution product safety label indicates that a hazard exists that
can result in injury and product damage if the instructions are not followed.
WARNING
WARNING indicates a potentially hazardous situation which, if not avoided, can result in death or serious injury.
Informatio n
CAUTION
CAUTION indicates a potentially hazardous situation which, if not avoided, can result in minor or moderate injury.
NOTICE
NOTICE used to address practices not related to physical injury. The safety alert symbol is not used with this signal word.
Safety and General Information
•
•
•
•
•
•
•
•
•
•
•
•
•
Adhere to all national and local electrical codes.
All wiring must be performed by a qualified electrician.
Changes and modifications to this unit not expressly approved by APC could void the warranty.
This UPS is intended for indoor use only.
Do not operate this UPS in direct sunlight, in contact with fluids, or where there is excessive dust or humidity.
Be sure the air vents on the UPS are not blocked. Allow adequate space for proper ventilation.
For a UPS with a factory installed power cord, connect the UPS power cable directly to a wall outlet. Do not use surge
protectors or extension cords.
The battery typically lasts for two to five years. Environmental factors impact battery life. Elevated ambient
temperatures, poor quality mains power, and frequent short duration discharges will shorten battery life.
The equipment is heavy. Always practice safe lifting techniques adequate for the weight of the equipment.
The batteries are heavy. Remove the batteries before installing the UPS and external battery packs (XLBPs), in a rack.
Always install XLBPs at the bottom in rack-mount configurations. The UPS must be installed above the XLBPs.
Always install peripheral equipment above the UPS in rack-mount configurations.
Additional safety information can be found in the Safety Guide supplied with this unit.
Deenergizing safety
The UPS contains internal batteries and may present a shock hazard even when disconnected from the branch circuit (mains).
Before installing or servicing the equipment verify the following:
• Mains circuit breaker is in the OFF position. The UPS is disconnected from mains or wall outlet.
• Internal UPS batteries are removed
• XLBP battery modules are disconnected
Electrical safety
• For models with a hardwired input, the connection to the branch circuit (mains) must be performed by a qualified
electrician.
• 230 V models only: In order to maintain compliance with the EMC directive for products sold in Europe, output cords
attached to the UPS must not exceed 10 meters in length.
• The protective earth conductor for the UPS carries the leakage current from the load devices (computer equipment).
An insulated ground conductor is to be installed as part of the branch circuit that supplies the UPS. The conductor
must have the same size and insulation material as the grounded and ungrounded branch circuit supply conductors.
The conductor will typically be green and with or without a yellow stripe.
Battery safety
• Before installing or replacing the batteries, remove jewelry such as wristwatches and rings.
High short circuit current through conductive materials could cause severe burns.
• Do not dispose of batteries by burning them. The batteries may explode.
• Do not open or mutilate batteries. Released electrolyte is harmful to the skin and eyes, and may be toxic.
General information
• The UPS will recognize as many as 10 external battery packs connected to the UPS. However there is no limit to the
number of XLBPs that can be used with the UPS.
Note: For each XLBP added, increased recharge time will be required.
• The model and serial numbers are located on a small, rear panel label. For some models, an additional label is located
on the chassis under the front bezel.
• Always recycle used batteries.
• Recycle the package materials or save them for reuse.
FCC Class A radio frequency warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are intended to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
2
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
Package Contents
Inspect the contents upon receipt. Notify the carrier and dealer if the unit is damaged.
Included with all models
Front bezel
RJ45 to DB9 cable
EPO Terminal block
User Documentation CD.
User Documentation
USB cable
Network Management Utility CD
Included with Tower models only
• 2 pairs stabilizer brackets
• 4 flat head screws to secure tower stabilizer brackets to the UPS
x4
Included with XLI/XLW-IEC models only
3 input power cords
1 output IEC jumper cable
Included with Rack-Mount models only
Rail Kit with instructions and hardware • 1 pair rack-mount brackets
for installing rails in a rack.
• 6 flat head screws to secure rack-mount brackets to the UPS
• 4 ornamental screws to secure rack-mount brackets to the rails
su0434a
x6
x4
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
3
Specifications
For additional specifications refer to the APC by Schneider Electric web site, www.apc.com.
Environmental
Temperature
Elevation
Operating
0º to 40º C (32º to 104º F)
Storage
-15º to 45º C (5º to 113º F)
Operating
0 - 3,000 m (0 - 10,000 ft)
Storage
0 - 15,000 m (50,000 ft)
Humidity
0% to 95% relative humidity, non-condensing
Protection Class
IP 20 rating
Note: Charge the battery modules every six months during storage.
Environmental factors impact battery life. Elevated ambient temperatures, high humidity, poor quality mains power, and
frequent short duration discharges will shorten battery life.
Physical
SRT2200XLI/SRT2200RMXLI model
The UPS is heavy. Follow all lifting guidelines.
Lifting guidelines
18 - 32 kg (40 - 70 lb)
32 - 55 kg (70 - 120 lb)
Unit weight batteries included, without packaging
25 kg (55 lb)
Unit weight batteries included, with packaging
Rack-Mount models: 34 kg (75 lb)
Tower models: 31 kg (68 lb)
Unit dimensions without packaging
Height x Width x Depth
85 (2U) mm x 432 mm x 585 mm
3.35 (2U) in x 17 in x 23 in
Unit dimensions with packaging
Height x Width x Depth
245 mm x 600 mm x 810 mm
9.7 in x 23.6 in x 31.9 in
The model and serial numbers are on a small label located on the rear panel.
SRT3000XLI/SRT3000RMXLI/SRT3000XLT/SRT3000RMXLT/SRT3000XLW-IEC/
SRT3000RMXLW-IEC model
The UPS is heavy. Follow all lifting guidelines.
Lifting guidelines
18 - 32 kg (40 - 70 lb)
32 - 55 kg (70 - 120 lb)
Unit weight batteries included, without packaging
31 kg (69 lb)
Unit weight batteries included, with packaging
Rack-Mount models: 40 kg (88 lb)
Tower models: 37 kg (81 lb)
Unit dimensions without packaging
Height x Width x Depth
85 (2U) mm x 432 mm x 636 mm
3.35 (2U) in x 17 in x 25 in
Unit dimensions with packaging
Height x Width x Depth
245 mm x 600 mm x 870 mm
9.7 in x 23.6 in x 34.3 in
The model and serial numbers are on a small label located on the rear panel.
4
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
Battery
SRT2200 models
Battery type
Replacement battery module
SRT3000 models
Maintenance free, leak proof, sealed, lead acid
APCRBC141
APCRBC152
This UPS has swappable battery modules.
Refer to the appropriate replacement battery user manual for
installation instructions.
Contact your dealer or go the APC by Schneider Electric web site,
www.apc.com for information on replacement batteries.
Number of battery modules
1 battery module
Voltage for each battery module
72 VDC
96 VDC
Total voltage for the UPS
72 VDC
96 VDC
Ah rating
5.1 Ah per battery module
XLBP cable length
500 mm (19.7 in)
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
5
Electrical
2200 VA / 1980 W
Building Circuit Breaker
(CB) Current Rating
16 A
3000 VA / 2700 W
20 A
Models
SRT2200XLI
Rating
SRT2200RMXLI
SRT3000XLI
SRT3000RMXLI
SRT3000XLT
20 A* / 2 pole
SRT3000RMXLT
SRT3000XLW-IEC
20 A IEC; 20 A UL* / 2 pole
SRT3000RMXLW-IEC
CAUTION
RISK OF FIRE, RISK OF DAMAGE TO EQUIPMENT OR PERSONNEL
* Connect the UPS models only to a circuit provided with 20 A maximum branch circuit overcurrent protection in
accordance with the National Electrical Code, ANSI/NFPA 70 and the Canadian Electrical Code, Part I, C22.1.
Failure to follow these instructions can result in fire, equipment damage and minor or moderate injury.
Output
Output Frequency
50 Hz / 60 Hz
Nominal Output Voltage
SRT2200XLI/SRT2200RMXLI/SRT3000XLI/SRT3000RMXLI: 220 V, 230 V, 240 V
SRT3000XLT/SRT3000RMXLT: 208 V, 240 V
SRT3000XLW-IEC/SRT3000RMXLW-IEC: 208V, 220V, 230V, 240V
Input
Input Frequency
40 Hz - 70 Hz
Nominal Input Voltage
SRT2200XLI/SRT2200RMXLI/SRT3000XLI/SRT3000RMXLI: 220 V, 230 V, 240 V
SRT3000XLT/SRT3000RMXLT: 208 V, 240 V
SRT3000XLW-IEC/SRT3000RMXLW-IEC: 208V, 220V, 230V, 240V
Input current rating
SRT2200 models: 13 A
SRT3000 models: 16 A
6
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
Remove Battery Module
CAUTION
DAMAGE TO EQUIPMENT OR PERSONNEL
• The equipment is heavy. Each APCRBC152 battery module weighs 16.4 kg (36.2 lb) and each APCRBC141 battery module
weighs 12.5 kg (27.6lb).
• Always practice safe lifting techniques adequate for the weight of the equipment.
• Remove the battery modules before installing the UPS.
• Use the battery module handle to slide the battery modules in or out of the UPS.
• Do not use the battery module handle to lift or carry the battery module.
Failure to follow these instructions can result in equipment damage and minor or moderate injury.
Use the battery module handle to lift and slide the battery module out of the UPS.


s uo 0
849b
s uo 0
850c
X3

SRT2200 models
s uo 0
858c
SRT3000 models
s uo0
85 1b
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
7
Rack-Mount Installation
Refer to the Rail Kit Installation Guide for instructions on rail installation.
CAUTION
DAMAGE TO EQUIPMENT OR PERSONNEL
• The equipment is heavy. Always practice safe lifting techniques adequate for the weight of the equipment.
• Always use the recommended number of screws to secure brackets to the UPS.
• Always use the recommended number of screws to secure the UPS to the rack.
• Always install the UPS at the bottom of the rack.
• Always install the XLBP below the UPS in the rack.
Failure to follow these instructions can result in equipment damage and minor or moderate injury


x3
s uo08
66c
x3
suo 0

867 b

x4
su o08
8
65b
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
su o08
68b


x3
69b
su o08

70b
su o08

x4
59a
su08
su o10
61a
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
9
Tower Installation
CAUTION
DAMAGE TO EQUIPMENT OR PERSONNEL
• The equipment is heavy. Each APCRBC152 battery module weighs 16.4 kg (36.2 lb) and each APCRBC141 battery module
weighs 12.5 kg (27.6lb).
• Always practice safe lifting techniques adequate for the weight of the equipment.
• Remove the battery modules before installing the UPS.
• Use the battery module handle to slide the battery modules in or out of the UPS.
• Do not use the battery module handle to lift or carry the battery module.
Failure to follow these instructions can result in equipment damage and minor or moderate injury

su 08
45 c

71c
suo 08

suo0873c
suo0872c

x3


10
suo1062a
suo0874c
x4
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
suo0875c

Rear Panel Features
Note: Refer to the table “Key to identify rear panel features” on page 12, that provides a key to the callout numbers for
the rear panel graphics depicted in this manual.
GROUP 1
10 AMP MAX
SRT2200XLI/SRT2200RMXLI/SRT3000XLI/SRT3000RMXLI
suo0882a
SRT3000XLT/SRT3000RMXLT
suo0883a
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
11
O VER LOA D
PR OTEC TO R
GROUP 1 MAX: 10 AMP IEC; 15 AMP UL
GROUP 2 MAX: 16 AMP IEC; 20 AMP UL
SRT3000XLW-IEC/SRT3000RMXLW-IEC
suo0884a
Key to identify rear panel features

SmartSlot
The SmartSlot can be used to connect optional management accessories.

AC input
power cable or
hardwire input box
SRT3000XLT, SRT3000RMXLT models have factory installed input power cables.

External battery
power and
communication
connector
Use the external battery cable on the XLBP to connect the UPS and XLBP.
XLBPs provide extended runtime during power outages. The UPS will automatically
recognize up to 10 external battery packs.

Controllable
outlet group 1
Connect electronic devices to these outlets.

Chassis ground screws The UPS and XLBPs have ground screws for connecting the ground leads. Prior to connecting
a ground lead, disconnect the UPS from mains power.

Controllable
outlet group 2
Connect electronic devices to these outlets.

EPO terminal
The Emergency Power Off (EPO) terminal allows the user to connect the UPS to a central
EPO system.

Serial Com
The Serial Com port is used to communicate with the UPS.
Use only interface kits supplied or approved by APC by Schneider Electric. Any other
serial interface cable will be incompatible with the UPS connector.

USB port
The USB port is used to connect either a server for native operating system communications,
or for software to communicate with the UPS.
Note: Serial and USB communication should not be used simultaneously. Use either the Serial
Com or the USB port.
12
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
UPS Configuration
Connect Emergency Power Off feature
For instructions on how to connect the Emergency Power Off (EPO) switch, refer to the Operation and Maintenance
manual on the User Documentation CD (supplied).
Configure controllable outlet groups
The outlets on the UPS are grouped. To configure the controlled outlet features, use the Advanced menus on the
display interface and navigate to: Main Menu > Configuration > Outlets > Outlet Group.
UPS Display Interface
 POWER ON/OFF button
Button illumination indications:
-No illumination, the UPS and the output
power are off
-White illumination, the UPS and the
output power are on
-Red illumination, the UPS is on and the
output power is off
 Load icon
Disable/mute audible alarm icon
LOAD
Output 230.0 v
On-Line
1
2
 UPS status information
 Operation mode icons
 ESCAPE button
 OK button
su0870b
 UP/DOWN buttons
 Controllable outlet group status icons
 Battery status icons
Display interface operation
Use the UP/DOWN buttons to scroll through the options. Press the OK button to accept the selected option. Press the
ESC button to return to the previous menu.
The icons on the LCD display interface screen may vary depending on the installed firmware version.
LOAD
Load icon: The approximate load capacity percentage is indicated by the number of load bar
sections illuminated. Each bar represents 16% of the load capacity.
Mute icon: Indicates the audible alarm is disabled/mute.
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
13
UPS Status Information
The status information field provides key information on the status of the UPS.
The Standard menu will allow the user to select one of the five screens listed below. Use the UP/DOWN buttons to scroll
through the screens.
The Advanced menu will scroll through the five screens automatically.
• Input Voltage
• Output Voltage
• Output Frequency
• Load
• Runtime
In the case of a UPS event, status updates will be displayed defining the event or condition that has occurred.
The display screen illuminates yellow to indicate a Message and red to indicate an Alert depending on the severity of the event
or condition.
Operation Mode Icons
On-Line mode: The UPS is supplying conditioned mains power to connected equipment.
Bypass mode: The UPS is in Bypass mode and the connected equipment will receive mains
power as long as the input voltage and frequency are within the configured limits.
Green mode: When in Green mode mains power is sent directly to the load.
In the event of a mains power outage, there will be an interruption in power to the load of up to
8 ms while the UPS switches to On-Line or Battery mode.
When enabling Green mode consideration should be given to devices that may be sensitive to
power fluctuations.
Indicates a UPS alert that requires attention.
UPS Status Icon
Battery mode: The UPS is supplying battery power to connected equipment.
The UPS has detected an internal fault with the battery. Follow the instructions on the screen.
X
The UPS has detected a critical fault with the battery. The battery is at the end of its life and has
to be replaced.
Controllable Outlet Group Icons
Controllable Outlet Group Power Available: The number next to the icon identifies the
specific outlet groups that have available power.
Controllable Outlet Group Power Not Available: The number next to the icon identifies
specific outlet groups that do not have available power.
14
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
Battery Status Icons
Battery Charge Status: Indicates the battery charge status.
Battery Charge In Progress: Indicates the battery is charging.
Menu overview
The display interface has Standard and Advanced menu screens. The preference for Standard or Advanced menu
selections is made during initial installation and can be changed at any time through the Configuration menu.
The Standard menus include the most commonly used options.
The Advanced menus provide additional options.
Note: Actual menu screens may differ by model and firmware version.
Refer to the UPS Operation Manual for menu configuration details.
Smart-UPS On-Line SRT2200/SRT3000 Tower/Rack-Mount 2U
15
LCD display interface angle adjustment
The angle of the LCD display interface can be adjusted for ease in viewing the displayed messages.
1. Remove the front bezel.
2. Locate the button on the bottom of the display interface panel.
3. Press the button and slide the bottom of the LCD display interface screen out. An audible click will be heard
when the screen reaches the maximum angle.
su
09
26
a
Select models are ENERGY STAR® qualified.
For more information go to www.apc.com/company/us/en/sustainability/energy-efficiency/
Customer support and warranty information are available on the APC by Schneider Electric web site,
www.apc.com.
© 2015 APC by Schneider Electric. APC, the APC logo, and Smart-UPS are owned by Schneider
Electric Industries S.A.S. or their affiliated companies. All other trademarks are property of their
respective owners.
EN 990-5268
4/2015
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising