Elo Touchcomputer User Guide for 15D1 15" LCD Multifunction

Elo Touchcomputer User Guide for 15D1 15" LCD Multifunction
15D1 Touchcomputer User Guide
15D1 15-inch LCD Multifunction Touchcomputer
[Model 15D1]
Elo TouchSystems
15D1 Touchcomputer User Guide
15-inch LCD Multifunction Touchcomputer
15D1
Revision A
P/N E674343
Elo TouchSystems
1-800-ELOTOUCH (1-800-356-8682)
www.elotouch.com
Copyright ©2008 Tyco Electronics. All Rights Reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical,
chemical, manual, or otherwise without prior written permission of Elo TouchSystems.
Disclaimer
The information in this document is subject to change without notice. Elo TouchSystems makes no representations or
warranties with respect to the contents hereof, and specifically disclaims any implied warranties of merchantability or fitness
for a particular purpose. References in this publication to Elo TouchSystems products or services do not imply that Elo
TouchSystems intends to make them available in all countries in which Elo TouchSystems operates. Elo TouchSystems
reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation
of Elo TouchSystems to notify any person of such revisions or changes.
Trademark Acknowledgments
Elo TouchSystems, IntelliTouch, SecureTouch, AccuTouch, MonitorMouse, TE logo, and Tyco Electronics are trademarks.
Other product names mentioned herein may be trademarks or registered trademarks of their respective companies. Tyco
Electronics claims no interest in trademarks other than its own.
iii
Table of Contents
Chapter 1:
Setup
1
Unpacking Your Touchcomputer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Adjusting the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Setting Up the Operating System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Selecting the Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Selecting the Time Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Testing Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Calibrating the Touchscreen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Securing the Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Advertising Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Chapter 2:
Operation
9
On-Screen Display (OSD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
OSD Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
OSD and Power Button Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
LED Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Base Power Status LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Head Power Status LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Touch Power Status LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
HDD Activity LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Using the I/O Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Chapter 3:
Options and Upgrades
16
Adding Optional Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Magnetic Stripe Reader (MSR). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Customer Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Fingerprint Reader (FPR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Barcode Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Wireless Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Third-Party Peripherals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Printer Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Cash Drawer Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Additional Hard Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Elo POS Demo Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Chapter 4:
Safety and Maintenance
27
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
TOUCHCOMPUTER 15D1 USER GUIDE
iv
Care and Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Warning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
WEEE Directive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Recovering the Operating System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Chapter 5:
Technical Specifications
30
Touchcomputer Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Connector Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Cash Drawer Port Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Display Screen Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Environmental Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Chapter 6:
Technical Support
37
Technical Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Using the Touchcomputer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Using the Web. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Using the Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Regulatory Information
39
Warranty
42
Index
44
TOUCHCOMPUTER 15D1 USER GUIDE
v
CHAPTER
1
Setup
This chapter discusses how to set up and test your touchcomputer. For information on
peripheral options, refer to Chapter 3, “Options and Upgrades.”
Unpacking Your Touchcomputer
Check that the following items are present and in good condition:
← AND →
Power cable US/Canada
Power cable Europe
Touchcomputer
Recovery DVD and
Quick Install Guide
TOUCHCOMPUTER 15D1 USER GUIDE
Ad clips
Optional
security screw
1
ADJUSTING THE DISPLAY
Adjusting the Display
The display screen can be adjusted from 0 to 60 degrees, as shown below.
60°
CAUTION: To protect the LCD, be sure to hold the base when adjusting the display, and
take care to not touch the screen.
Setting Up the Operating System
The initial setup of the operating system takes approximately 5-10 minutes. Additional
time might be needed depending on touchcomputer hardware configuration and
connected devices.
To set up the Windows OS for the touchcomputer, turn on the touchcomputer and follow
the instructions on the screen.
Selecting the Language
Windows uses English as the default language in menus and dialog boxes. You can
change this language to suit your preferences. Follow these steps.
1. In the Control Panel, select Regional and Language Options.
TOUCHCOMPUTER 15D1 USER GUIDE
2
SETTING UP THE OPERATING SYSTEM
2. Click Customize. The Regional and Language Options window appears. Select the
Languages tab.
3. If required, check the boxes for “Install files for complex script and right-to-left
languages” and “Install files for East Asian languages.”
4. Select the Regional Options tab.
5. Select your preferred language from the drop-down list in the Standards and formats
pane.
TOUCHCOMPUTER 15D1 USER GUIDE
3
SETTING UP THE OPERATING SYSTEM
6. Click Apply.
7. Select your location from the drop-down list in the Locations pane.
8. Click OK.
TOUCHCOMPUTER 15D1 USER GUIDE
4
TESTING PERIPHERALS
Selecting the Time Zone
When the following window appears, you can change the time zone, date, and time of
the touchcomputer.
After making any changes, click Next to finish. Windows Setup completes the
installation of the touchcomputer.
Testing Peripherals
The touchcomputer can be configured with several different optional peripherals, such
as a MSR or cash drawer. To test an optional peripheral that is installed on the
touchcomputer, refer to the instructions in Chapter 3, “Options and Upgrades.”
NOTE: Testing icons are located on the desktop. Testing a particular peripheral can only
be done after the device is properly installed.
Calibrating the Touchscreen
The touchscreen is pre-calibrated for accurate touch response.
If for any reason the touchscreen needs to be recalibrated, right-click the Elo icon in the
Task bar and then click “Properties.” The following window opens.
NOTE: Calibration not applicable to APR models.
TOUCHCOMPUTER 15D1 USER GUIDE
5
CALIBRATING THE TOUCHSCREEN
Click the Align button. This launches the calibration program. The window shown
below opens. Follow the instructions to calibrate the touchscreen.
TOUCHCOMPUTER 15D1 USER GUIDE
6
SECURING THE BASE
Securing the Base
There are two mounting options for the 15D1 touchcomputer. In both cases, the base
must be mounted on a horizontal surface.
Option 1: Secure from below. Use the four pretapped holes to secure the four m6
screws from below the mounting surface.
◆ Option 2: Secure from top. Use the two through holes to secure the base to the
surface.
◆
NOTE: Mounting screws are not provided with the shipment.
Refer to the figure below for the location of the holes. All dimensions are in millimeters.
Option 2 through holes
Option 1 Pretapped holes
Advertising Brackets
Advertising brackets are provided to allow the user to display ads on the back of the
15D1 touchcomputer. These brackets are included separately in the accessory box. The
maximum size of the advertising material is 220mm X 320mm (8.6” X 12.6”).
To install these brackets, simply push them onto the back door of the 15D1
touchcomputer, as shown in the figure below.
TOUCHCOMPUTER 15D1 USER GUIDE
7
ADVERTISING BRACKETS
Then insert the advertising material as shown below.
TOUCHCOMPUTER 15D1 USER GUIDE
8
CHAPTER
2
Operation
This chapter describes how to control the On-Screen Display (OSD), power buttons, and
I/O panel.
All adjustments made to the OSD and power controls are automatically saved. User
settings remain unchanged after powering off/on or in the case of a power failure.
34 5 6 7 8 9
1
2
TOUCHCOMPUTER 15D1 USER GUIDE
1. HDD status LED
2. Computer power LED
3. Head power LED
4. Touch power LED
5. Menu button
6. Left button
7. Right button
8. Select button
9. Power ON/OFF button
9
ON-SCREEN DISPLAY (OSD)
On-Screen Display (OSD)
OSD Menu
1. To display the OSD Menu, press the Menu button.
Press the RIGHT button or LEFT button to toggle and the SELECT button to select
from the different OSD sub-menus and functions.
2. When the function you want to change is shown, press the SELECT button.
To adjust the value of the function:
1. Pressing the RIGHT button increases the value of the selected OSD control option.
2. Pressing the LEFT button decreases the value of the selected OSD control option.
The OSD provides the following settings.
Feature
Description
Auto adjust
Automatically adjusts system clock.
Brightness
Adjust brightness and contrast.
Image setting
‹
Brightness: Adjusts the backlight of the monitor.
‹
Contrast: Adjusts the maximum luminance level of the monitor.
Adjusts H position, V position, clock, and phase.
‹
H position: Moves the screen horizontally right and left (1 pixel
pitch increment).
‹
V position: Moves the screen vertically up and down (1 line
increment).
‹
Clock: Adjusts the ratio of dividing frequency of the dot clock.
‹
Phase: Adjusts the phase of the dot clock.
Color
Sets color temperature (9300K, 7500K, 6500K, 5500K, or User
Preset).
OSD
Adjusts H position, V position, and OSD timeout.
‹
H position: Adjusts the OSD menu screen position left or right.
‹
V position: Adjusts the OSD menu screen position up or down.
‹
Timeout: Adjusts the amount of time that the OSD menu is
displayed.
Language
Changes language to English, French, Italian, German, Spanish,
Japanese, Simplified Chinese, or Traditional Chinese.
Recall
Sets color recall and recall defaults. Restores original factory
settings.
TOUCHCOMPUTER 15D1 USER GUIDE
10
LED FUNCTIONALITY
Feature
Description
Miscellaneous
Adjusts sharpness, enables/disables DDCCI function.
‹
Exit
Sharpness: Adjusts sharpness of video.
Exits the OSD.
OSD and Power Button Control
The OSD menu and power button are enabled by default.
To enable or disable the OSD function:
1. Simultaneously press Menu/Exit and the Left (<-) key for two seconds. A window
appears displaying OSD ENABLE or OSD DISABLE.
2. When the OSD is disabled, the OSD menu is not visible.
To enable or disable the power button lock function:
1. Simultaneously press Menu/Exit and the Right (->) key for two seconds. A window
appears displaying PWR ENABLE or PWR DISABLE.
2. When the power button lock feature is activated, the power button is disabled.
LED Functionality
Base Power Status LED
The 15D1 base has two LEDs that indicate the power status and hard drive status. See
the figure on page 9, item 1 for the location of this LED. The light can be green, flashing
green, red, or off. The table below shows LED state and corresponding color.
LED Color to Observer
State
Off
No input power — Off mode
Red
Input power present, power switch off — Off mode
Flashes green
Input power present — Sleep mode
Green
Input power present — On mode
Head Power Status LED
The head power status is indicated by a different LED, which is located at the lower edge
of the head (#3 in figure on page 9).
TOUCHCOMPUTER 15D1 USER GUIDE
11
LED FUNCTIONALITY
LED Color to Observer
State
Off
No input power to head — Off mode
Red
Input power present, power switch off — Off mode
Amber
Input power present — Sleep mode
Green
Input power present — On mode
Touch Power Status LED
The touch power status is indicated by a separate LED located at the lower edge of the
head and to the right of the Head Power Status LED (#4 in figure on page 9). This
feature is available for AT and APR 7010.
LED Color to Observer
State
Off
No input power — Off mode
Red
Input power present, power switch off — Off mode
Amber
Input power present — Sleep mode
Green
Input power present — On mode
HDD Activity LED
Hard disk drive activity is indicated by a flashing LED on the base, just under the
computer power LED (#2 in the figure on page 9). Reading from and writing to the disk
causes the LED to flash.
LED Color to Observer
State
Off
No activity
Flashes green
Activity
TOUCHCOMPUTER 15D1 USER GUIDE
12
USING THE I/O PANEL
Using the I/O Panel
To access the I/O ports, open the cable cover door on the left side of the unit, as shown
below.
Optional security
screw
Opening for
cables
The touchcomputer provides a number of I/O interfaces for connecting a wide variety
of compliant devices as shown in the following figure.
TOUCHCOMPUTER 15D1 USER GUIDE
13
USING THE I/O PANEL
1
2
8
9
3
10
11
4
12
13
5
14
6
7
TOUCHCOMPUTER 15D1 USER GUIDE
15
14
USING THE I/O PANEL
Number Port
Description
1
Audio in (left), out (center), mic (right)
Audio
‹
Audio In
‹
Audio Out: One 3.5mm stereo audio output jack for
connecting headphones or external powered
speakers
‹
Microphone Input: One 3.5mm microphone input jack
for connecting an external microphone
2
Ethernet
One RJ45 Ethernet port providing LAN capabilities
3, 8, 9
USB
Seven USB 2.0 type A ports
4
VGA
One D-SUB VGA output port for connecting the display
head
5
Parallel
Standard 25-pin connector port
6
Serial
Three standard serial ports
7
PS/2 universal
Mouse (left) and keyboard (right)
8
Customer display Customer display / USB 2.0; the max loading on this port
is 5VDC @ 1.5A
10
Printer power
One 24V DC printer power port
11
Compact flash
Standard CF port
12
Speaker power
Power switch for internal speakers
13
Cash drawer
RJ11, 6 position (12V/24V default)
14
Powered serial
Two powered serial ports, 5V default/12V
15
Main power
AC power
NOTE: The Customer display, fingerprint reader and barcode scanner are designed to
connect to the USB 2.0 ports on the I/O panel. If all three peripherals were
connected, there would be four USB 2.0 ports remaining.
TOUCHCOMPUTER 15D1 USER GUIDE
15
CHAPTER
3
Options and Upgrades
Adding Optional Peripherals
When adding a peripheral, complete installation and setup instructions are provided
with the field-installable kits. The following peripherals are available in field-installable
kits:
◆
◆
◆
◆
◆
◆
◆
Magnetic stripe reader (MSR)
Customer display
Fingerprint reader (FPR)
Barcode scanner (1-D or omni-directional/2-D)
Wireless miniPCI kit
Hard disk drive
Printer power cable
NOTE: The peripherals described are all options that are purchased separately.
NOTE: Testing software is available in the folder 15D1 Test Applications, which is
located on the Desktop.
TOUCHCOMPUTER 15D1 USER GUIDE
16
ADDING OPTIONAL PERIPHERALS
Barcode
scanner
Magnetic stripe
reader (MSR)
Fingerprint
reader (FPR)
Magnetic Stripe Reader (MSR)
You can add a magnetic stripe reader (MSR) to the 15D1 touchcomputer using a USB
port located on the display head.
The MSR is a USB 2.0 device that reads all three data stripes on standard credit cards
or driver’s licenses conforming to ISO/ANSI standards. The MSR has foreign language
capability. The credit card is read by sliding the credit card forward or backward through
the MSR, stripe side toward the display. The MSR is powered from the USB port; no
external power is needed. The MSR features are:
◆
◆
◆
◆
◆
◆
◆
◆
◆
◆
Reads up to 3 tracks of information
Bidirectional swipe reading
Superior reading of high jitter, scratched, and worn MagStripe cards
Reliable for over 1,000,000 card swipes
Reads ISO7811, AAMVA, and most other card data formats
PC software makes configuration changes easy
Swipe speeds from 3 to 60 inches per second
Interfaces: USB-KB and USB-HID
Fully supports USB 2.0
Elo part number E145919
TOUCHCOMPUTER 15D1 USER GUIDE
17
ADDING OPTIONAL PERIPHERALS
Testing the MSR
Testing in USB MSR Keyboard (KB) Emulation Mode
1. Open Notepad.
2. Slide the card through the MSR and verify that the data is displayed in the application
window.
Testing in USB MSR Human Interface Device (HID) Mode
1. Double-click the MagSwipe HID Demo icon to start the test application.
2. Slide a card through the MSR and verify that the data is displayed in the application
window.
3. If the card ID appears in the Reader Output window, the reader is functioning.
TOUCHCOMPUTER 15D1 USER GUIDE
18
ADDING OPTIONAL PERIPHERALS
Customer Display
You can optionally add a customer display to the 15D1 touchcomputer. Each display has
two lines of 20 characters (2x20 VFD).
The customer display can be adjusted to a 30 degree range up and down and swivels 30
degrees side to side.
Customer
display
Display rotates 30° up
and down, and swivels
30° left to right
Feature
Description
Display type
Vacuum fluorescent display
Display color
Red
Display pattern
5 x 7 dot matrix
Brightness
350-600 cd/m2
Characters available
95 alphanumeric & 32 international characters
Dot size (X x Y)
0.86 x 1.2 mm
Font size
5.5(W) x 10.5(H)
Character number
20 characters by 2 lines, for a 5 x 7 dot matrix font
Interface
USB
Part number
E326629
TOUCHCOMPUTER 15D1 USER GUIDE
19
ADDING OPTIONAL PERIPHERALS
Testing the Customer Display
To test the customer display, follow these steps:
1. Double-click the VFD Test icon.
2. Select the correct COM port (refer to Device Manager).
3. Enter a line of text into the Text: field.
4. Click Initialize.
5. Verify that the device shows the line of text entered.
Fingerprint Reader (FPR)
The fingerprint reader is powered by the USB bus. The reader optically scans the
fingerprint when the user touches the glowing window. Optical technology gives the
highest quality fingerprint scans and reliability.
Partial fingerprint reader specifications are shown in the table below.
Feature
Specification
Fingerprint reader
DigitalPersona U.are.U 4000B
Power supply
5.0VDC +/- 0.25V
Current draw – scanning mode
190 mA (typical)
Current draw – idle mode
140 mA (typical)
Current draw – suspend mode
1.5 mA (typical)
Image resolution
512 dpi
Image color
8-bit gray level
Scan capture size
14.6mm (nominal width) x 18.1mm (nominal length)
Image capture speed
100 ms
TOUCHCOMPUTER 15D1 USER GUIDE
20
ADDING OPTIONAL PERIPHERALS
Feature
Specification
USB type
1.0, 1.1, or 2.0
Operating temperature
0 to 40°C
Electrostatic discharge (ESD)
Up to 15kV mounted in case
Part number
E373639
Testing the FPR
1. Double-click the Fingerprint Reader Test icon to start the test application.
2. Place your finger on the fingerprint reader sensor and verify that the image of your
fingerprint is displayed on the application window.
Barcode Scanner
There are two optional USB barcode scanners (1-D or omni-directional). The barcode
scanner is only an option if the speaker bar is present.
When a scanner is chosen, a USB-SSI (Simple Serial Interface) converter board is
included. Both barcode scanners are powered with the USB interface.
◆
One-dimensional scanner (Elo P/N E946856) specifications:
- Ability to generate 1-D scanning pattern
- Low-cost solution
- USB powered
TOUCHCOMPUTER 15D1 USER GUIDE
21
ADDING OPTIONAL PERIPHERALS
- Easy communication between host and scanner
- Visible laser diode operating at 650nm
- 100+ scans/sec.
- RoHS-compliant
◆ Omni-directional scanner (Elo P/N E449881) specifications:
- Ability to generate omni-directional scanning pattern
- Maximum performance
- 2-D scanning ability (PDF417, MicroPDF)
- USB powered
- Easy communication between host and scanner
- Visible laser diode operating at 650nm
- 600+ scans/sec.
- RoHS compliant
◆ USB-SSI converter board (Elo P/N E580321) specifications:
- Ability to convert from serial interface to USB interface and vice versa.
- Compact size
- Input voltage: 5V
- BuzzerWireless card
Enabling 2-D Scanning
The scanner default settings do not enable 2-D barcode reading ability. To enable this
option, follow these steps:
1. Scan the barcodes below to enable PDF417 and MicroPDF417. These are both types
of 2-D barcodes.
2. Now scan the barcode below to change the scanning pattern. Using this scanning
pattern allows you to read 2-D barcodes (you can still read 1-D barcodes).
TOUCHCOMPUTER 15D1 USER GUIDE
22
ADDING OPTIONAL PERIPHERALS
Testing the Barcode Scanner
1. Determine which port the barcode scanner is using:
a. In the Windows Control Panel, start the Computer Management application.
b. In Computer Management, select Device Manager. In the right pane, look under
the Ports section, and note the COM value of the USB-Serial Port object.
2. Double-click the Barcode Scanner Test icon to start the following application:
3. Change the port value to match the value you retrieved from the Device Manager.
4. Click Connect. You should see the text connected in the Messages field.
5. In the box labeled Param Number, enter the value 238.
6. In the box labeled New Value enter the value 1.
7. Check the box labeled Permanent Param Change.
8. Scan a barcode (sample given below). The scanned data should appear in the
“Messages” section of SSIContainer.
TOUCHCOMPUTER 15D1 USER GUIDE
23
ADDING OPTIONAL PERIPHERALS
The barcode scanner also has the ability to run in USB-KB emulation mode. To enable
this option, please install the required drivers. To find the drivers:
1. Click the 15D1 Setup Files folder on the Desktop.
2. Then click the Barcode Scanner folder.
3. Finally, click the Keyboard Emulation Setup Files folder, where you can find setup
instructions to complete the installation process.
Wireless Card
A wireless card can be installed as an option in the 15D1 touchcomputer to provide
wireless LAN capabilities using a miniPCI slot. A PCI to miniPCI converter board is
provided in the wireless kit.
Typical specifications for the wireless card are:
◆
◆
◆
◆
◆
◆
◆
MiniPCI interface
Compliant to MiniPCI industry-standard sizing
802.11b/g compliant
Two UFL connectors
Support for Windows 2000, Windows XP, and Windows Vista 32
RoHS compliant
Elo P/N E238795
Testing the Wireless Card
To test the wireless card:
1. From the desktop, click Start > Control Panel > Network Connections.
2. Double-click the Wireless Network Connections icon to display available
networks and verify that the wireless network is detected.
NOTE: If a wireless network needs to be initialized, please see your system
administrator.
TOUCHCOMPUTER 15D1 USER GUIDE
24
THIRD-PARTY PERIPHERALS
Third-Party Peripherals
The 15D1 touchcomputer includes two pre-configured ports for a printer and cash
drawer. These peripherals are not available from Elo TouchSystems.
Printer Port
A 24VDC printer power port to connect a compatible receipt printer is provided. The
24VDC printer power cable is Elo P/N E337867. This port has been tested with Epson
TM-T88IV Series printers.
Cash Drawer Port
We provide a standard RJ11 port to attach a cash drawer. The touchcomputer is
compatible with the following APG models:
◆
◆
MultiPro 320 with CD-005A cable
MultiPro 420 with CD-039A cable
Testing the Cash Drawer Port
1. Connect the cash drawer to the touchcomputer using a cable with the correct wiring
definition.
2. Click the FD2XX Test icon to start the test program.
The screen displays “Display is open.”
3. Turn off the test equipment.
The screen displays “Display is closed.”
TOUCHCOMPUTER 15D1 USER GUIDE
25
THIRD-PARTY PERIPHERALS
4. Click Send 200ms.
The software automatically turns on the cash drawer.
For additional information, see “Cash Drawer Port Specifications” on page 34.
Additional Hard Drives
The 15D1 touchcomputer comes with one standard 80GB hard disk drive. You can add
an optional second SATA hard disk drive (Elo P/N E828965).
Elo POS Demo Software
POS demo software created by Elo TouchSystems is located on the Desktop. The
software can be found in the folder Elo POS Demo Software.
TOUCHCOMPUTER 15D1 USER GUIDE
26
CHAPTER
4
Safety and Maintenance
Safety
Here is some important information on the proper setup and maintenance of your
touchcomputer.
◆
◆
◆
◆
◆
To reduce the risk of electric shock, follow all safety notices and never open the
touchcomputer case.
Turn off the product before cleaning (refer to “Care and Handling” on page 28 for
proper cleaning methods).
Your touchcomputer is equipped with a 3-wire, grounding power cord. The power
cord plug only fits into a grounded outlet. Do not attempt to fit the plug into an outlet
that has not been configured for this purpose. Do not use a damaged power cord.
Only use the power cord that comes with your Elo TouchSystems touchcomputer.
Use of an unauthorized power cord might invalidate your warranty.
The slots located on the sides and top of the touchcomputer case are for ventilation.
Do not block or insert anything inside the ventilation slots.
It is important that your touchcomputer remains dry. Do not pour liquid into or onto
your touchcomputer. If your touchcomputer becomes wet, do not attempt to repair it
yourself.
TOUCHCOMPUTER 15D1 USER GUIDE
27
CARE AND HANDLING
Care and Handling
The following tips help keep your touchcomputer functioning at the optimal level.
◆
◆
◆
◆
◆
◆
To avoid risk of electric shock, do not disassemble the power adapter or display unit
cabinet. The unit is not user serviceable. Remember to unplug the display unit from
the power outlet before cleaning.
Do not use alcohol (methyl, ethyl, or isopropyl) or any strong solvent. Do not use
thinner or benzene, abrasive cleaners, or compressed air.
To clean the display unit cabinet, use a cloth lightly dampened with a mild detergent.
Avoid getting liquids inside your touchcomputer. If liquid does get inside, have a
qualified service technician check it before you power it on again.
Do not wipe the screen with a cloth or sponge that could scratch the surface.
To clean the touchscreen, use window or glass cleaner. Put the cleaner on the rag and
wipe the touchscreen. Never apply the cleaner directly on the touchscreen.
Warning
This product consists of devices that might contain mercury, which must be recycled or
disposed of in accordance with local, state, or federal laws. (Within this system, the
backlight lamps in the monitor display contain mercury.)
WEEE Directive
In the European Union, the Waste Electrical and Electronic Equipment (WEEE)
directive label shown to the left indicates that this product should not be disposed of
with household waste. It should be deposited at an appropriate facility to enable
recovery and recycling.
TOUCHCOMPUTER 15D1 USER GUIDE
28
RECOVERING THE OPERATING SYSTEM
Recovering the Operating System
If for any reason the touchcomputer’s operating system and software need to be
recovered, insert the included recovery disk into an external DVD-ROM drive and
reboot the touchcomputer. Follow the on-screen instructions to complete recovery.
NOTE: All data is deleted during the recovery process. The user must back up files when
necessary. Elo TouchSystems does not accept liability for lost data or software.
NOTE: The end-user must adhere to Microsoft's Licensing Agreement.
TOUCHCOMPUTER 15D1 USER GUIDE
29
CHAPTER
5
Technical Specifications
Touchcomputer Specifications
NOTE: Not all operating systems or options are supported in all regions. Please contact
your local Elo TouchSystems representative for details.
Feature
Description
Processor
Intel Celeron 430M 1.8GHz CPU 512K L2 cache, w/800MHz
front-side bus, LGA775 Pkg
RAM
512MB 667MHz DDR2 standard on one slot
Two slots are available. Recommended vendor is Transcend.
Expandable up to 4GB max—DDR2-667(PC2-5400) or
DDR2-800(PC2-6400)
Dual channel
Northbridge
Intel G31
Southbridge
Intel ICH7
Audio
Azalia ALC883 Codec, 6 audio channels
Video
Intel GMA 3100 (Vista Aero compatible)
TOUCHCOMPUTER 15D1 USER GUIDE
30
TOUCHCOMPUTER SPECIFICATIONS
Feature
Description
Operating system
Microsoft Windows XP Professional SP3
Microsoft Windows Embedded for Point of Service (WEPOS)
Microsoft Windows Vista Business
Ports
7 x USB 2.0 ports
1 x 12V/24V default cash drawer port (jumper selectable)
3 x RS232 serial ports
2 x 5V default/12V powered RS232 serial ports (jumper
selectable)
2 x PS/2 (keyboard and mouse)
Audio ports
1 x 3.5mm mic-in
1 x 3.5mm audio-in
1 x 3.5mm audio-out
Networking
1 x 10/100BASE-T Ethernet port (LAN RJ45)
BIOS
AMI
Real-time clock
Replaceable lithium-ion battery for clock
Storage
1 x 2.5-inch 80GB SATA HDD (minimum, optional second
drive)
1 Compact Flash type I (tested with Transcend, Apacer,
Kingston, and SanDisk)
Power supply
Internal 12VDC universal-type power supply brick
AC input voltage: 100-240V AC
Input frequency: 50-60Hz
Input current: 2.5-5A
Max output power: 270W
DC output:
+3.3V / 5.0A
+5V / 16.0A
+12V / 12.0A
+24V / 2.3A
+5Vsb / 3A
-12V / 0.4A
TOUCHCOMPUTER 15D1 USER GUIDE
31
TOUCHCOMPUTER SPECIFICATIONS
Feature
Description
Max. power rating
15D1 touchcomputer (without peripherals, receipt printer,
cash drawer, or power serial ports connected: 169.95 W
Cash drawer: 2.4 W max.
Receipt printer; 45.6 W max.
Powered serial ports: 24 W max
Total power drawn with all possible peripherals: 252.45 W
Touch technologies
Acoustic Pulse Recognition (APR)
AccuTouch (AT)
IntelliTouch (IT)
Touchcomputer
dimensions (max.)
Width: 345 mm
Height: 288 mm
Depth: 212 mm
Dimensions vary with tilt angle and options selected
Shipping box
dimensions
Width: 450mm
Height: 475mm
Depth: 340mm
Weight with no options Actual: 10.03kg (22.1 lb.)
Shipping: 12.16kg (26.8 lb.)
Display
15-inch diagonal
4x3 aspect ratio
Active matrix TFT LCD
Optimal (native)
resolution
1024 x 768
Backlight lamp life
Minimum 50,000 hours to half brightness
Agency approvals
UL/cUL, CE, BSMI, NOM, AR, CCC, EK, KCC, GOST-R,
RCM, C-Tick, VCCI
Speakers (internal)
Two 2-Watt/channel speakers
User controls
Power and user controls with lockout function for public use
TOUCHCOMPUTER 15D1 USER GUIDE
32
CONNECTOR SPECIFICATIONS
Feature
Description
Other features
User-accessible hard drive
Touchscreen sealed to bezel and LCD
Security lock receptacle, Kensington
Peripheral options and Magnetic stripe reader, 3 tracks
upgrades
Customer display 2 x 20 VFD
Biometric fingerprint reader
Barcode scanner (1-D or omni/2-D)
Second 80GB hard drive
Wireless card
Printer power cable
Connector Specifications
Serial Ports
Pin #
Standard Ports Signal Name
Powered Ports Signal Name
1
SER DCD
SER DCD
2
SER RXD
SER RXD
3
SER TXD
SER TXD
4
SER DTR
SER DTR
5
SER GND
SER GND
6
SER DSR
SER DSR
7
SER RTS
SER RTS
8
SER CTS
SER CTS
9
SER RI
5V(default)/ 12V
Printer Power Input Pin Definition
Pin #
Signal Name
1
+24V
2
NC
3
Ground
4
Flat
TOUCHCOMPUTER 15D1 USER GUIDE
33
CONNECTOR SPECIFICATIONS
Serial Port Power Selection
J2/J3
Setting
Function
All pins open
No power
Pins 1-2 short/closed
5V (default)
Pins 2-3 short/closed
12V
Cash Drawer Port Specifications
The cash drawer port is 12/24V compatible.
Cash Drawer Port Signal Definition
Pin #
Signal Name
1
Frame ground
2
CD 1 drawer kick-out drive signal 1
3
SW ( + ) connected on the side of the open/closed detection
switch on the drawer
4
L ( + ) +12V/24V (default) for drawer kick-out supplied
5
CD 2-drawer kick-out drive signal 2
6
( - ) Ground
Cash Drawer Port Power Selection
J1
TOUCHCOMPUTER 15D1 USER GUIDE
Setting
Function
Pins 1-2 short/closed
12V
Pins 2-3 short/closed
24V (default)
34
DISPLAY SCREEN SPECIFICATIONS
Display Screen Specifications
Feature
Specification
LCD display
15.0-inch diagonal TFT active matrix LCD
Video input signal
Analog RGB (0.7Vp-p)
Data display channel (DDC) DDC1, 2B compliant (EDID data only)
function (plug & play)
Display size (useful screen
area)
304.128mm (H) x 228.096mm (V)
Maximum touchcomputer
dimensions
288mm (H) x 345mm (W) x 212mm (D)
Pixel pitch
0.297mm (H) x 0.297mm (V)
Display mode
VGA 640 x 350 (70Hz)
* Dimensions vary with tilt angle and options selected
VGA 720 x 400 (70Hz)
VGA 640 x 480 (60Hz)
MAC 640 x 480 (66Hz)
VESA 640 x 480 (72 / 75Hz)
VESA 800 x 600 (56 / 60 / 72 / 75Hz)
MAC 832 x 624 (75Hz)
VESA 1024 x 768 (60 / 70 / 75Hz)
SUN 1024 x 768 (65Hz)
NOTE: If input fH>60kHz, or fV>75Hz, then OSD
displays an out of range warning
Brightness (typical)
No touch
225 cd/m2 (typical); 170 cd/m2 (min.)
AccuTouch
200 cd/m2 (typical); 150 cd/m2 (min.)
IntelliTouch
225 cd/m2 (typical); 170 cd/m2 (min.)
APR (7000 and 7010)
225 cd/m2 (typical); 170 cd/m2 (min.)
Response time
Trise: 2.3 ms (typical)
Tfall: 6 ms (typical)
Display color
16.7 million colors
Vertical viewing angle
(up/down)
60° looking up typical at a CR=10
TOUCHCOMPUTER 15D1 USER GUIDE
65° looking down typical at a CR=10
35
ENVIRONMENTAL SPECIFICATIONS
Feature
Specification
Horizontal viewing angle
(left/right)
70° looking left typical at a CR=10
Contrast ratio
700:1 (typical)
Optional touchscreens
AccuTouch, IntelliTouch, Acoustic Pulse Recognition
7000 and 7010
70° looking right typical at a CR=10
Environmental Specifications
Feature
Specification
Temperature Ranges
Operating (independent of altitude)
0 to 35°C
Non-operating (independent of altitude)
-20 to 60°C
Humidity
Operating (noncondensing)
20 to 80%
Non-operating (38.7°C maximum wet bulb 5 to 95%
temperature)
Altitude
Operating
0 to + 12,000 feet [3,658m]
Equivalent to 14.7 to 10.1 psia
Non-operating
0 to + 40,000 feet [12,192m]
Equivalent to 14.7 to 4.4 psia
TOUCHCOMPUTER 15D1 USER GUIDE
36
CHAPTER
6
Technical Support
Technical Assistance
There are three methods to obtain contact information for technical assistance on the
touchcomputer:
The touchcomputer
◆ The web
◆ The phone
◆
Using the Touchcomputer
You can access support information in System Properties by clicking the Support
Information button. You can get to System Properties by either of the following
methods:
Right click My Computer and choose Properties.
or
◆ Click the Start button, select Control Panel, and double-click the System icon.
◆
TOUCHCOMPUTER 15D1 USER GUIDE
37
TECHNICAL ASSISTANCE
Using the Web
For online self-help, go to www.elotouch.com/go/websupport.
For technical support, go to www.elotouch.com/go/contactsupport.
For current Elo news, product updates, and announcements, or to register to receive our
Touchcomputer newsletter, go to www.elotouch.com/go/news.
Using the Phone
Call toll-free 1-800-ELO-TOUCH (1-800-356-8682).
TOUCHCOMPUTER 15D1 USER GUIDE
38
Regulatory Information
I.
Electrical Safety Information
A. Compliance is required with respect to the voltage, frequency, and current
requirements indicated on the manufacturer’s label. Connection to a different
power source than those specified herein may result in improper operation,
damage to the equipment, invalidation of warranty, or a fire hazard if the
requirements are not followed.
B. There are no operator-serviceable parts inside this equipment. There are
hazardous voltages generated by this equipment which constitute a safety
hazard. Service should be provided only by a qualified service technician.
C. This equipment is provided with a detachable power cord which has an integral
safety ground wire intended for connection to a grounded safety outlet.
1. Do not substitute the cord with other than the provided approved type.
Under no circumstances use an adapter plug to connect to a 2-wire outlet as
this defeats the continuity of the grounding wire.
2. The equipment requires the use of the ground wire as a part of the safety
certification. Modification or misuse can provide a shock hazard that can
result in serious injury or death.
3. Contact a qualified electrician or the manufacturer if there are questions
about the installation prior to connecting the equipment to main power.
II. Emissions and Immunity Information
A. Notice to Users in the United States: This equipment has been tested and found
to comply with the limits for a Class A digital device, pursuant to Part 15 of
FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential or commercial installation. This equipment
generates, uses, and can radiate radio frequency energy, and if not installed and
used in accordance with the instructions, may cause harmful interference to
radio communications.
B. Notice to Users in Canada: This equipment complies with the Class A limits for
radio noise emissions from digital apparatus as established by the Radio
Interference Regulations of Industry Canada.
C. Notice to Users in the European Union: Use only the provided power cords and
interconnecting cabling provided with the equipment. Substitution of provided
cords and cabling may compromise electrical safety or CE Mark Certification
for emissions or immunity as required by the following standards: This
Information Technology Equipment (ITE) is required to have a CE Mark on the
manufacturer’s label which means that the equipment has been tested to the
following Directives and Standards:
TOUCHCOMPUTER 15D1 USER GUIDE
39
This equipment has been tested to the requirements for the CE Mark as required
by EMC Directive 89/336/EEC indicated in European Standard EN 55022
Class A and the Low Voltage Directive 73/23/EEC as indicated in European
Standard EN 60950.
D. General Information to all Users: This equipment generates, uses, and can
radiate radio frequency energy. If not installed and used according to this
manual, the equipment may cause interference with radio and television
communications. There is, however, no guarantee that interference will not
occur in any particular installation due to site-specific factors.
1. In order to meet emission and immunity requirements, the user must
observe the following:
a. Use only the provided I/O cables to connect this digital device with any
computer.
b. To ensure compliance, use only the provided manufacturer’s approved
power cord.
c. The user is cautioned that changes or modifications to the equipment
not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
2. If this equipment appears to cause interference with radio or television
reception, or any other device:
a. Verify as an emission source by turning the equipment off and on.
b. If you determine that this equipment is causing the interference, try to
correct the interference by using one or more of the following
measures:
i.
Move the digital device away from the affected receiver.
ii. Reposition (turn) the digital device with respect to the affected
receiver.
iii. Reorient the affected receiver’s antenna.
iv. Plug the digital device into a different AC outlet so the digital
device and the receiver are on different branch circuits.
v. Disconnect and remove any I/O cables that the digital device does
not use. (Unterminated I/O cables are a potential source of high RF
emission levels.)
vi. Plug the digital device into only a grounded outlet receptacle. Do
not use AC adapter plugs. (Removing or cutting the line cord
ground may increase RF emission levels and may also present a
lethal shock hazard to the user.)
vii. If you need additional help, consult your dealer, manufacturer, or
an experienced radio or television technician.
TOUCHCOMPUTER 15D1 USER GUIDE
40
III. Agency Certifications
The following certifications have been issued for the monitor:
◆
Argentina S-Mark
◆
FCC
◆
Russia PCT
◆
Australia C-Tick
◆
IMERC
◆
Taiwan BSMI
◆
CE
◆
Japan VCCI
◆
UL
◆
China CCC
◆
Korea EK/KCC
◆
cUL
◆
China RoHS
◆
Mexico NOM
◆
WEEE
TOUCHCOMPUTER 15D1 USER GUIDE
41
Warranty
Except as otherwise stated herein or in an order acknowledgment delivered to Buyer,
Seller warrants to Buyer that the Product shall be free of defects in materials and
workmanship. With the exception of the negotiated warranty periods; the warranty for
the touchcomputer and components of the product is 3 years.
Seller makes no warranty regarding the model life of components. Seller’s suppliers
may at any time and from time to time make changes in the components delivered as
Products or components. Buyer shall notify Seller in writing promptly (and in no case
later than thirty (30) days after discovery) of the failure of any Product to conform to the
warranty set forth above; shall describe in commercially reasonable detail in such notice
the symptoms associated with such failure; and shall provide to Seller the opportunity
to inspect such Products as installed, if possible. The notice must be received by Seller
during the Warranty Period for such product, unless otherwise directed in writing by the
Seller. Within thirty (30) days after submitting such notice, Buyer shall package the
allegedly defective Product in its original shipping carton(s) or a functional equivalent
and shall ship to Seller at Buyer’s expense and risk.
Within a reasonable time after receipt of the allegedly defective Product and verification
by Seller that the Product fails to meet the warranty set forth above, Seller shall correct
such failure by, at Seller’s options, either (i) modifying or repairing the Product or (ii)
replacing the Product. Such modification, repair, or replacement and the return shipment
of the Product with minimum insurance to Buyer shall be at Seller’s expense. Buyer
shall bear the risk of loss or damage in transit, and may insure the Product. Buyer shall
reimburse Seller for transportation cost incurred for Product returned but not found by
Seller to be defective. Modification or repair, of Products may, at Seller’s option, take
place either at Seller’s facilities or at Buyer’s premises. If Seller is unable to modify,
repair, or replace a Product to conform to the warranty set forth above, then Seller shall,
at Seller’s option, either refund to Buyer or credit to Buyer’s account the purchase price
of the Product less depreciation calculated on a straight-line basis over Seller’s stated
Warranty Period.
THESE REMEDIES SHALL BE THE BUYER’S EXCLUSIVE REMEDIES FOR
BREACH OF WARRANTY. EXCEPT FOR THE EXPRESS WARRANTY SET
FORTH ABOVE, SELLER GRANTS NO OTHER WARRANTIES, EXPRESS OR
IMPLIED BY STATUTE OR OTHERWISE, REGARDING THE PRODUCTS,
THEIR FITNESS FOR ANY PURPOSE, THEIR QUALITY, THEIR
MERCHANTABILITY, THEIR NONINFRINGEMENT, OR OTHERWISE. NO
EMPLOYEE OF SELLER OR ANY OTHER PARTY IS AUTHORIZED TO MAKE
ANY WARRANTY FOR THE GOODS OTHER THAN THE WARRANTY SET
FORTH HEREIN. SELLER’S LIABILITY UNDER THE WARRANTY SHALL BE
LIMITED TO A REFUND OF THE PURCHASE PRICE OF THE PRODUCT. IN NO
EVENT SHALL SELLER BE LIABLE FOR THE COST OF PROCUREMENT OR
INSTALLATION OF SUBSTITUTE GOODS BY BUYER OR FOR ANY SPECIAL,
CONSEQUENTIAL, INDIRECT, OR INCIDENTAL DAMAGES.
TOUCHCOMPUTER 15D1 USER GUIDE
42
Buyer assumes the risk and agrees to indemnify Seller against and hold Seller harmless
from all liability relating to (i) assessing the suitability for Buyer’s intended use of the
Products and of any system design or drawing and (ii) determining the compliance of
Buyer’s use of the Products with applicable laws, regulations, codes, and standards.
Buyer retains and accepts full responsibility for all warranty and other claims relating to
or arising from Buyer’s products, which include or incorporate Products or components
manufactured or supplied by Seller. Buyer is solely responsible for any and all
representations and warranties regarding the Products made or authorized by Buyer.
Buyer will indemnify Seller and hold Seller harmless from any liability, claims, loss,
cost, or expenses (including reasonable attorney’s fees) attributable to Buyer’s products
or representations or warranties concerning same.
TOUCHCOMPUTER 15D1 USER GUIDE
43
Index
A
F
address, Elo TouchSystems 46
audio ports, description 15
fingerprint reader (FPR)
overview 20
specifications 20
testing 21
B
barcode scanner
enabling 2-D scanning 22
overview 21
specifications 21
testing 23
base power status 11
base, securing 7
box contents 1
C
cables
included 1
printer power 25
calibration 5
cash drawer port
overview 25
port description 15
specifications 34
testing 25
certifications 41
contact information 37
controls, location diagram 9
customer display
overview 19
customer support 37
H
head power status 12
I
I/O panel
accessing 13
illustration 13
L
language selection 2
LCD
adjusting 2
specifications 35
LEDs
base 11
hard drives 12
head 12
location diagram 9
touch 12
touchpad 12
M
display screen
adjusting 2
specifications 35
magnetic stripe reader (MSR)
overview 17
testing 18
maintenance 28
care and handling 27
software 29
mounting options 7
E
O
D
email, Elo TouchSystems 46
enabling or disabling power 11
environmental specifications 36
Ethernet port 15
TOUCHCOMPUTER 15D1 USER GUIDE
on-screen display (OSD)
enabling or disabling menu 11
menu settings 10
operating system
recovering 29
44
setting up 2
operation 9
options, adding 16
P
parallel ports 15
peripherals
adding 16
third-party 25
phone number, Elo TouchSystems 38, 46
ports
accessing 13
audio 15
cash drawer 15
Ethernet 15
illustration 13
parallel 15
printer 15
PS/2 Universal 15
serial 15
USB 15
VGA 15
power
base 11
enabling or disabling button lock 11
printer power port
about 25
cables 25
description 15
specifications 33
PS/2 Universal port 15
R
receipt printer specifications 25
regulatory information 39
S
safety 27
serial ports
description 15
specifications 34
setup
display screen 2
language 2
mounting options 7
operating system 2
time zone 5
touchscreen calibration 5
unpacking 1
TOUCHCOMPUTER 15D1 USER GUIDE
software recovery 29
specifications
barcode scanner 21
cash drawer port 34
display screen 35
environmental 36
FPR 20
hardware 30
printer power port 33
receipt printer 25
serial ports 33, 34
technical 30 to 36
T
technical specifications 30 to 36
technical support 37
third-party peripherals 25
time zone selection 5
touch power status 12
touchpad power status 12
touchscreen
calibrating 5
care and handling 28
2-D scanning, enabling 22
U
upgrades, adding 16
USB ports 15
V
VGA port description 15
W
warranty 42
website, Elo TouchSystems 38, 46
WEEE directive 28
wireless card
overview 24
testing 24
45
Check out Elo’s Website!
www.elotouch.com
Get the latest...
◆
Product information
◆
Specifications
◆
News on upcoming events
◆
Press release
◆
Software drivers
◆
TouchMonitor Newsletter
Getting in Touch with Elo
To find out more about Elo’s extensive range of touch solutions, visit our website at
www.elotouch.com or simply call the office nearest you:
Germany
Belgium
Asia-Pacific
Elo TouchSystems
301 Constitution Drive
Menlo Park, CA 94025
USA
Tyco Electronics Raychem GmbH
(Elo TouchSystems Division)
Finsinger Feld 1
D-85521 Ottobrunn
Germany
Tyco Electronics Raychem N.V.
(Elo TouchSystems Division)
Diestsesteenweg 692
B-3010 Kessel-Lo
Belgium
Sun Hamada Bldg. 2F
1-19-20 ShinYokohama
Kanagawa 222-0033
Japan
(800) ELO-TOUCH
(800) 356-8682
Tel 650-361-4800
Fax 650-361-4722
customerservice@elotouch.com
Tel +49 (0)(89) 60822-0
Fax +49(0)(89) 60822-180
elosales@elotouch.com
Tel +32(0)(16)35 21 00
Fax +32(0)(16)35 21 01
elosales@elotouch.com
Tel +81(45)478-2161
Fax +81(45)478-2180
www.tps.co.jp
©2008 Tyco Electronics Printed in USA
North America
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising