Jive Instructions
Contents
n Brief introduction…………...…………………………..…....1
n Before use……………………………………………………..1
1. Overview…………………………………………………...……1
2. Charging for headset..……………………………………………2
n Getting started……..…………………………………………3
1. Turning on/off the headset…………....……………………......3
2. Wearing the headset.......................................................................3
3. Pairing/connecting…….……..............................……………..….4
1) Pairing headset with Bluetooth cell phone via Bluetooth……..….4
2) Pairing headset with Bluetooth cell phone via NFC......................5
3) Pairing headset with multi devices via Bluetooth ….............…....6
4. Making a call with the headset………………………………...….6
5. Playing music………………………………………………..…...9
6. LED indicator………………………………………………....10
7. Factory Reset………………………………………………..….10
n Care and maintenance……………………………..………..11
n FAQs……………………………………...…………………..11
n Specification……………………………...………………..…12
Thank you for purchasing the K3 Jive Sport Bluetooth Stereo In-Ear
Headphones. Please read this user guide carefully before use.
n Brief introduction
The K3 Jive is a sport In-ear Bluetooth stereo headset; designed for ultimate
portability and functionality within today’s mobile world. IPX 4 certified,
water, moisture & sweat resistant for premium sport performance.
n Before use
1. Overview
1
Cover of charging jack
6
NFC area
2
Micro USB charging jack
7
LED indicator
3
+ :volume up/previous song
8
Microphone
4
: Multi-functions button
9
Optional Ear Tip (s)
5
—: volume down/next song
10
Stabilizer
11
CableManagement
(optional)
1
2. Charging for headset
The headset comes with a built-in rechargeable battery, prior to using it, it is
recommended to charge the battery completely prior to initial use. When the
headset is low power, the headset emits prompt tones every 5 minutes and
the red LED flashes. Please recharge the battery of the headset.
Using USB cable
1. Open the cover of charging jack, and plug the USB charging cable
2. Plug another side of cable to the USB port of PC
Red light on: Charging
Red light off: Charging is complete
3. It will takes about 2 hours to finish charging
Remarks:
1) The lithium battery is recyclable.
2) Batteries (battery pack or batteries installed) shall not be exposed to
excessive heat place, such as sunshine, fire or the like.
2
n Getting started
1. Turning on/off the headset
Functions
Operation
Prompt tone
Turning on
Press and hold
about 4
Four raise tone
seconds until blue LED flashes
Turning off
Press and hold
about 4
Four fall tone
seconds until red LED flashes
Remark: In order to save power, the headset will turn off automatically if
no devices can be connected after 5 minutes.
2. Wearing the headset
a. Put the stabilizer into the headset and rotate to the suitable position as
following shown:
3
b. Choose the suitable size ear tip (s) according to your ear and comfort as
following shown:
c. Set up the cable management clips (optional accessory) for optimum
in-use performance:
3. Pairing/connecting
1) Pairing headset with Bluetooth cell phone via Bluetooth
Prior to using the headset for the first time, you have to pair it with a
Bluetooth-enabled cell phone. The pairing procedures are subject to
different models of cell phones. Please refer to your cell phone user’s
manual for further information.
The general pairing procedures are as follows:
1) Keep your headset turned off and within 1 meter of phone ;
2) Press and hold
about 8 seconds until the red and blue LED flash
alternately, the headset enter into paring mode;
4
3) Activate your cell phone’s Bluetooth function and search for Bluetooth
devices within range, select “K3 JIVE” from the list of devices shown
(enter password “0000 ” if the headset prompt);
4) After successful connecting, blue LED of headset flashes twice every 4
seconds
Remarks:
u Pairing mode will last 2 minutes, the headset will back to standby mode
if the pairing failure.
u If the pairing is not successful, turn off the headset and repeat the steps as
above.
u Every time the headset is turned on, it will connect to last connected
device automatically. The headset can remember 8 paired devices, when
the number of paired devices exceeds 8, the first one will be replaced.
2) Pairing headset with a Bluetooth cell phone via NFC
K3 Jive supports NFC technology, it can quickly connect with Bluetooth
cell phone via NFC.
The general pairing procedures are as follows:
1) Please activate the Bluetooth and NFC function of cell phone;
2) Pairing and connecting with cell phone. Please refer to following
pictures:
5
Remarks:
l Please keep the NFC area of cell phone and headset within 1 centimeter
until the red and blue LED of headset flash alternately(First pairing time
maybe 3 seconds).
l The headset will disconnect when you make the NFC area of cell phone
and headset touch each other again.
3) Pairing headset with multi devices via Bluetooth
The headset can connect with two Bluetooth cell phones at the same time.
The general pairing procedures are as follows:
1) Pairing the headset with device one
2) Turn on the headset and make it enter pairing mode again, and pairing it
with device two
3) Operate device one to connect with headset. The headset has already
connected with two devices in this moment
Remarks:
l The multi-pair function is off in factory set, please turn on this function as
following:
Turn on: long press
and + button under standby mode(not connected
device), and release it until you hear four raise tone
Turn off: long press
and — button under standby mode(not
connected
device), and release it until you hear four raise tone
l To improve the stabilization of headset, we suggest you turn off the
multi-pair function when you only connect with one cell phone.
4. Making a call with the headset
1) Basic operation
Functions
Status of
headset
Cancel a call
Calling
Answer a call
Incoming
ringing
call
Operation
Short
press
once
Short press
once
Prompt tone
One
tone
Two
tone
short
raise
6
Reject a call
Incoming
ringing
End a call
During a call
Volume up
During a call
Volume
down
Transfer
conversation
to
mobile
phone
Transfer
conversation
to headset
Microphone
mute
Cancel mute
During a call
call
Long press
about 2 seconds
and release it
until listen a
tone
Short press
once
Short press +
button
Short press —
button
Long press
about 2 seconds
Two fall tone
During a call
During a call
During a call
During a call
(microphone
mute)
Voice dial
Standby mode
(connected
device)
Redial
the
Standby mode
last number
(connected
device)
Warning: Excessive pressure from
cause hearing loss.
One
tone
short
One
tone
short
Long press
about 2 seconds
One
tone
short
Long press “+”
about 2 seconds
Long press “+”
about 2 seconds
Two fall tone
Two
tone
raise
Short press
and“+” button
simultaneously
Double click
button
One
tone
short
One
tone
short
earphones and headphones can
7
Note:
u Not all mobile phones support all the functions listed above. Different
function and prompt tone according to different mobile phone. Please
refer to your mobile phone user’s manual.
u When the volume is adjusted to max or min, you will hear one prompt
tone.
u When the headset under microphone mute mode, you will hear two tone
continuously every 10 seconds.
u When pressing the answer button on some mobile phones, the call will be
transferred to the mobile phone. You can switch the call to the headset by
using the conversation switch button or through operating on the mobile
phone. Please refer to your mobile phone user manual for further
information.
2) Three-way call operation
Functions
Status of headsets
Answer new call and
There are second
end current call
incoming call
Answer new call and
There are second
retain current call
incoming call
Switch calls
Keep conversation
End current call and
switch retain call
Keep conversation
Operation
Short press
once
Double click
button
Double click
button
Short press
once
8
3) Connect with two cell phones
Functions
Status of headset
End phone call #1
During phone call #1,
and answer phone
phone 2 has incoming
call #2
call
Retain phone call #1
During phone call #1,
and answer phone
phone 2 has incoming
call #2
call
Switch call
During call, one of
phone call is retained
End current call,
During call, one of
back to retain phone
phone call is retained
call
5. Playing music
Functions
Status of the
headset
Volume up
Playing music
Volume
Playing music
down
Last song
Playing music
Next song
Playing music
Pause
Playing music
play
Pausing
Operation
Short press
Double
button
once
click
Double click
button
Short press
once
Operation
Short press “+”button
Short press “―”button
Long press “+”button
Long press “―”button
Short press
once
Short press
once
Notes:
u When the volume is adjusted to max or min., you will hear one prompt
tone.
u If you want to remote control last/next song, pause/play, it needs your
Bluetooth mobile phone or Bluetooth transmitter paired with the headset
to support AVRCP profile, please refer to the user’s manual of your
mobile phone or Bluetooth transmitter for further information.
6. LED indicator
LED indicator
Red and blue LED flashes
alternately
Blue LED flashes once every 2
seconds
Blue LED flashes twice every 4
seconds
Red LED flashes instead of blue
LED
9
Status of headset
Pairing mode
Not connected to device
Connected to device
Low battery
7. Factory Reset
In the status of charging, long press “+” button about 4 seconds and release
it until the red and blue LED flashes simultaneously, you will hear 4 prompt
tone.
Remarks:
After factory reset, the paired list of headset will be deleted. After turn it on
again, the headset will enter pairing mode automatically, and you need to
re-pair and connect with Bluetooth devices.
n Care and maintenance
Read the following recommendations carefully before using K3 Sport In Ear
Headphones. Following these you will be able to enjoy this product for
many years.
u Please note that the cord management clips are optional accessory for
better wearing.
u Keep the product away from direct sunlight or hot places. High
temperatures will shorten the life of electronic devices, destroy the
battery or distort certain plastic parts.
u Don’t expose the product to cold areas. It may damage the internal circuit
board.
u Don’t try to disassemble the product as it may get damaged if you are not
professional.
u Don’t let it fall down onto the floor or other hard surfaces. The internal
circuit might get damaged.
u Don’t use intensive chemical products or detergent to clean the product.
10
n FAQs
1.What does it mean when red LED flashes instead of blue LED?
Battery is low power, need to be recharged.
2.Why is the red LED off when charging?
a) Please make sure the charging device connect with headset well;
b) Please charge the battery for 30 minutes, and then the red LED will be
ON.
3.Why my mobile phone unable to search and find the headset?
Please make sure the headset is under the pairing mode and in the effective
working range, and then the headset can be paired and connected.
4. Why mobile phone unable to pair with headset via NFC?
a) Make sure activate NFC function of your mobile phone
b) Please keep the NFC chip of cell phone and headset within 1 centimeter
until the red and blue LED of headset flash alternately (First pairing
time maybe 3 seconds).
5. Why can’t I hear the sound on the headset?
c) Make sure the headset has been switched on;
d) Make sure the volume is not too low or muted;
e) Make sure the headset connects with the mobile phone correctly;
f) Make sure the distance between the headset and the cell phone is in the
available Bluetooth range.
6. Why can’t I hear the sound clearly on the headset?
a) Make sure the mobile phone is in the strong signal area;
b) Make sure the headset is in the available range of this product.
7. Who to contact if you are in need of support?
Please reach out directly to: Support@thek3company.com
8. Why the pause/play, last/next song not function when playing music?
Make sure your Bluetooth device supports AVRCP (Audio/Video Remote
Control profile)
11
n Specifications
Bluetooth version
Bluetooth profiles
Operating distance
Headset music time
Headset talk time
Standby time
Headset charging time
Dimension
Weight
NFC Technology
Bluetooth V4.0
Headset, Hands free, A2DP, AVRCP
10meters
About 5 hours
About 5.5 hours
About 200 hours
About 2 hours
Headset: 37x16.3x27.7 mm
Cable: about 500mm
About 13 g
Allows for close pairing/connect
Notes:
1. This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
K3 Sport In-Ear Headphones are designed for the active & outdoor
enthusiast.
Each K3 model protected against moisture, water &
perspiration by Liquipel, an award winning Water Safe ™ Technology.
“Work Hard & Play Hard with K3 Sport Products”
WWW.THEK3COMPANY.COM
12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising