Inserting Memory Card Locate the Micro SD Card port

Inserting Memory Card Locate the Micro SD Card port
Inserting Memory Card
Locate the Micro SD Card port and insert a new memory card. San Disk 8GB or 16GB cards are recommended. If a used card
is used, it may have to be formatted before use.
Installing / Removing Battery
Use fingernail to press button toward arrow while simultaneously using other hand to pry open battery cover. To remove
battery, pull tab of battery to take it out. To insert new battery, look inside battery storage area for connection terminal and
make sure battery will align correctly. Then use fingernail to press button toward arrow while simultaneously using other hand
to replace battery door cover.
Charging
Charging the battery can either be done internally or externally. To charge battery internally, connect the micro USB cord to
the camera and the wall charger power supply, then connect to a wall outlet. Connect micro USB cord to the camera and a
vehicle charger plug, then to vehicle’s cigarette lighter power outlet. Connect micro USB cord to camera and then connect to
computer’s USB. To charge battery externally, use a GhostPro Quick Charger. Remove battery from camera and insert into the
charger, then plug charger into wall outlet.
Powering Camera On / Off
Press and hold MODE button on front of camera for about 5 seconds to turn on or to turn off.
Mode
To change between filming video, taking photos, playback, or camera menu, press MODE button.
Video Recording Mode
Make sure that a new San Disk micro SD card is inserted into the camera. Turn camera on. Press OK button to record video.
A blinking red light on the LED screen will indicate that the camera is recording video.
Photo Mode
To take still photos, turn camera on. Press MODE button to go into still image mode. Press OK button to take a photo.
Playback Mode
To review footage, turn camera on. Press MODE button to go into the playback mode. Press OK button to take a photo.
Menu
To use menu, press MODE button until you get into the gray setup screen.
Menu -> Resolution
To change camera’s resolution, press OK when “Resolution” is highlighted. Use up and down arrows to go to disired resolution
and when highlighted, press OK. 1080P FHD at 30FPS, 720P HD at 60FPS, 720P HD at 30FPS, and WVGA resolutions are
available.
Menu -> Cyclic Record
To change the length and the size of the individual video file, select between 3 minutes, 5 minutes, and 10 minutes segments.
Or choose “Off” for camera to record one large file. Choose minute segments to prevent loss of footage in case battery is
depleted.
Menu -> Audio
Select “On” for camera to record audio. Choose “Off” for camera to not record audio.
Menu -> Date Stamp
Video date stamp.
Menu -> Image Size
Use to select 12MP, 10MP, 8MP, and 5MP.
Menu -> Quality
Use to select size and quality of image.
Menu -> Sharpness
Sharpness settings.
Menu -> White Balance
White balance settings.
Menu -> Color
Color settings.
Menu -> ISO
ISO settings.
Menu -> Exposure
Exposure settings.
Menu -> Anti-Shaking
Stabilization mode.
Menu -> Quick Review
Quick review mode.
Menu -> Date Stamp
Image date stamp.
Menu -> Language
Language settings.
Menu-> Date/Time
Change camera’s date and time for timestamp.
Menu->Auto Power Off
Auto power off setting.
Menu-> Beep Sound
Use to turn on or off beep sound.
Menu-> TV Mode
TV Mode setting.
Menu-> Screensaver
Length of time LCD will stay on. Turn to “Off” for LCD screen to stay on continuously.
Menu-> Frequency
Frequency setting.
Menu-> Rotate
Use to rotate screen.
Menu-> Car Mode
Dash cam mode.
Menu-> OSD Mode
Onscreen display.
Menu-> Format
Use to format used SD card so it will work for camera.
Menu-> Default Setting
Use to restore camera to default settings.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising