TOU232-Kit, 307614, - Fibre Optic LNB, SAT-IF + DTT/DAB - K-DIGI

TOU232-Kit, 307614, - Fibre Optic LNB, SAT-IF + DTT/DAB - K-DIGI
TOU232-Kit, 307614, - Fibre Optic LNB, SAT-IF + DTT/DAB
Universal Single LNB with FC/PC Fibre Optic output. For external PSU.
Key points:
♦ All 4 Ku-Band polarities are transmitted over one single Fibre Optic cable.
♦ Uses 1310/1550nm optical technology with very low cable loss (<0.3dBm/km).
♦ Allows very large distribution networks to be built with practically no
distance limitation compared to traditional coax cabling.
♦ SAT-IF signals (950 – 2150 MHz each polarity)
♦ TER/DAB digital signals (no analogue signals possible)
♦ Uses 2 meter N-toN connector High Quality RF cable
♦ Power supply from ODU unit (PSU included in kit)
Use this LNB when:
♦ …You need to have a very large cable distribution in your satellite distribution network
♦ …You need to build larger multi switch systems than normally possible using coax.
♦ …You need to hide your dish away out of sight far from the building with the
distribution network.
♦ …You need digital DTT signals and/or DAB signals in addition to SAT-IF
♦ …You need more than the 32 ways splitting provided by the TOL32 System.
♦ …You have no space for bulky coax cabling
♦ …You need to be able to expand your distribution network easily at a later time
♦ …You want to have a state of the art technology and installation
♦ …one, any combination or all of the above are true.
To be aware of:
♦ The TOU232-Kit is for Ku-Band reception ONLY (4 polarities).
♦ The TOU232-Kit provides SAT-IF signals and DTT/DAB. Only digital TER signals are allowed.
Any analogue signal must be suppressed >28dB.
♦ A maximum of 2 x 32 way splits possible (Optical Link budget approx. 20-22dBm)
♦ 2 times 32 way splitting means that each of the two outputs provide a maximum of
32 way splitting (this is NOT the same as 1 x 64 way splitting in terms of cabling!).
Other products that work well with the TOU232-Kit:
307622: TVC04, Virtual Optical QUAD Converter, SAT-IF only, no DTT/DAB
307624: TVQ04, Virtual Optical QUATTRO Converter, SAT-IF only, no DTT/DAB
307626: TVC05, Virtual Optical QUAD Converter, SAT-IF and DTT/DAB output
307628, TLQ05, Virtual Optical QUATTRO Converter, SAT-IF and DTT/DAB output
All FC/PC pre-connected Triax Fibre Optical Cables, Splitters and other accessories
Rev. 1.0, 10-2011, JNY
TOU232-Kit, Fibre Optical LNB, 307614
Page 1
Typical components of a TOU232-Kit installation:
Input for digital DDT/DAB signal.
NOTE: there must be NO analogue
signals present here. ANY analogue
signal must be suppressed min. 28dB!
Universal Single
Ku-Band LNB
‘Sidecar unit’
TWL01 LNB
TOU232-SA
Fixed 2 meter
High Quality, High
Frequency cable
w/ N-connectors
TUC001
Indoor
Outdoor
Sidecar has two identical fibre optical
outputs, each providing same laser
power budget as TOL32 = splitting
possible into 32 ways.
Two wavelengths used (1310/1550nm)
Rest of second distribution
network not shown here
(but can be identical to
below example)
Switch Mode Power Supply
(included with TOU232-Kit)
100-240VAC, 50/60Hz
Please NOTE:
Many combinations of
optical spiltters can be
used, as long as each
branch is only split into a
maximum of 32 ways counted top to bottom
(here it is 2 x 4 x 4 = 32).
Other split combinations
per branch can be:
2 x 2 x 2 x 2 x 2, or
2 x 4 x 2 x 2, or
2 x 2 x 4 x 2, or
4 x 4 x 2, or
4x2x2x2
(the two last 4x examples
would not work in this
drawing, as the first 2x
splitter counts into every
branch)
NOTE:
Using the TOU232-Kit and
the Sidecar unit you will
always have 2 optical
outputs, and you need to
treat them as 2 x 32 way
splitting networks.
2x
2 Way Optical Splitter
w/ built-in connectors
4 Way Optical Splitters
w/ pigtail connectors
Both types of Splitters (pigtail and built-in
connectors) can be used anywhere in the
system. Let the mounting position decide
what suits best.
NOTE: Splitters MUST be dual-window type!
(Both 1310 and 1550nm)
4x
Counted from the Sidecar unit and to every
individual Virtual TVC/TVQ Converter a
maximum of 32 way splits can be performed
(The 4 outputs shown below are split to the
maximum: 2x4x4 = 32 ways)
4x
Switch Mode Power Supply
(included with TVQ units)
TVQ04
QUATTRO
To different parts of the fibre optic
distribution network for a total
maximum of 32 Virtual Converters.
(Not shown in this drawing)
1 to n
SetTop
boxes
Multi
switch
TVC04
QUAD
NOTE: TVC/TVQ04 units does
NOT provide a TER output!
TVC units are powered from STB
You CANNOT use it as a
1 x 64 way splitting
distribution!
1 to 4
SetTop
boxes
Switch Mode Power Supply
(included with TVQ units)
TLQ05
QUATTRO
TER
Legend:
= FC/PC optical connector
= Coax F-connector
= FC/PC-to-FC/PC optical assembly connector
= FC/PC Pre-connected
3.0 mm armored fibre optical cable,
Singlemode type, G657.A, LSZH
(Available in 1, 3, 5, 10, 15, 20, 30, 40, 50,
75, 100, 200 and 500 meter length)
Rev. 1.0, 10-2011, JNY
1 to n
SetTop
Boxes +
TER
Multi
switch
TLC05
QUAD
TVC units are powered from STB
1 to 4
SetTop
boxes
TOU232-Kit, Fibre Optical LNB, 307614
TER
Any one of the TLC/TLQ Virtual Converters
can be used at any fibre end-point
Page 2
Ku-Band Universal Single LNB
SAT-IF plus DTT/DAB inputs and Fibre Optic output.
For external power supply.
TOU232-Kit
TOU232-Kit
P/N: 307614
The Kit comprises:
1 x TWL01 LNB
P/N: 307612
1 x TOU232SA/ODU32 ’Sidecar’
P/N: 307615
1 x TUC001 RF cable
P/N: 307617
1 x PSU
P/N: 307xxx
1 x Optical Terminator
P/N: 307xxx
1 x Boot gel tightener
P/N: 307xxx
General description:
A Triax TOU232-Kit is everything needed outdoor to realize a Universal Single Ku-Band LNB with a Fibre Optic
1310/1550nm output providing both a SAT-IF and a DTT/DAB signal.
The LNB constantly receives all 4 Ku-Band polarities, and uses a frequency stacking technique to put all four
SAT-IF polarities into one large broadband frequency range of 950 to 5450 MHz.
This signal is transmitted via a 2 meter High Quality RF-cable to a second unit (called a Sidecar) where a
1310nm laser puts all 4 polarities on two standard singlemode fibre optical cable outputs. The Sidecar
furthermore provides one input for a digital DTT/DAB signal that is transmitted via a 1550nm laser over the
same optical outputs, and a PSU input to power both Sidecar electronics and LNB. All units are for outdoor
use, mounting brackets are provided in kit.
Used together with Virtual Converters (TVC/TVQ or TLC/TLQ) at the other end of the fibre optic distribution
network, the converters (Receiver Nodes) transform terrestrial DTT/DAB signals and the four SAT-IF polarities
back into the traditional 4 polarities: Vertical and Horisontal both in Low and High Band frequencies.
NOTE: only TLC05/TLQ05 type Converter units can provide a DTT/DAB output.
Providing an optical power link budget of approximately 20-22dBm, this means that each passive singlemode
fibre network cable output can be spilt into a maximum of 32 ways each feeding one Virtual Converter.
The Virtual Converters comes in two versions:
TVC, which is a QUAD type unit with 4 outputs each for direct connection to a SetTop box, and the
TVQ which is a QUATTRO type unit. This allows further distribution via a multi switch system.
Rev. 1.0, 10-2011, JNY
TOU232-Kit, Fibre Optical LNB, 307614
Page 3
Technical Specifications:
Specifications:
Input frequency
LNB Output frequency
Sidecar input
Laser output
Laser power
Hor. and Vert.
Broadband SAT
TER/DAB
TER/DTT
Wavelength SAT
Wavelength TER
Optical Power
Noise Figure
Gain
Gain flatness
Gain Ripple
Phase Noise
(±2dB)
Per Band
per 26 MHz band
LO stability
(-40ºC to +60ºC)
10 Year Life
Image rejection
Cross Polarization
Spurious output
Output connectors
Supply voltage
Current consumption
Neck mounting diameter
Temperature
In band
DC input
Optical output
Max.
TOU232-Kit, P/N: 307614
10.7 – 12,75
950 - 5450
213-230
470 - 854
1310
1550
7 nominal at 25ºC,
±2dBm over full temp. range
Typ. @25ºC
Max. @25ºC
0,5
1,1
Max. Gain
Min. Gain
72
62
5
<±0,5
Offset freq.
Max. limit
Unit
GHz
MHz
MHz
MHz
nm
nm
dBm
dB
dB
dB
dB
1 kHz
10kHz
100kHz
-55
-80
-100
dBc/Hz
dBc/Hz
dBc/Hz
1 MHz
Condition
Init. Setting
Temp drift
Aging
-110
Max. var.
±1
±2
±4
dBc/Hz
40, min.
Typ. 30, Min. 25
-25
Female F-connector
Female FC/PC
12
<450
40ø
Condition
Limits
Ambient
-30 to +60
Storage
-40 to +70
MHz
MHz
MHz
dB
dB
dBc
VDC
mA
mm
ºC
ºC
Also available :
Rev. 1.0, 10-2011, JNY
TOU232-Kit, Fibre Optical LNB, 307614
Page 4
TWL01 LNB
TWL01 LNB
not available as single item.
P/N: 307612
Included in the TOU232-Kit:
P/N 307614
General description:
The TWL01 LNB, a part of the TOU232-Kit, constantly receives all 4 Ku-Band polarities, and uses a frequency
stacking technique to put all four SAT-IF polarities into one large broadband frequency range of 950 to 5450
MHz. This signal is transmitted via a 2 meter High Quality RF-cable to a second unit (called a Sidecar)
It is possible to split the signal out of the TWL01 into 2, 3 or 4 ways (using the TAS04 – Active Splitter unit –
see separate datasheet) before reaching the High Frequency input of a TOU232 Sidecar unit.
Using the TAS04 it is possible to expand from a single 2 x 32 = 64 optical output system to a total of 128, 192
or a 256 optical output system. Note that the 256 optical outputs are 2 x 32 x 4.
This is physically 8 fibre optical outputs out of the 4 x Sidecars, which means that from the LNB-end your fibre
optical cabling start with an 8 way distribution network, each with a total of 32 way split distribution.
Rev. 1.0, 10-2011, JNY
TOU232-Kit, Fibre Optical LNB, 307614
Page 5
For specifications: see TOU232-Kit.
Rev. 1.0, 10-2011, JNY
TOU232-Kit, Fibre Optical LNB, 307614
Page 6
Sidecar
Outdoor fibre optical unit
TOU232-SA
TOU232SA (stand alone)
To be purchased as a single item if
used in a larger system (128, 192 or 256 outputs)
P/N: 307615
1 x Included in the TOU232-Kit:
P/N 307614
General description:
The TOU232-SA is a stand alone ‘Sidecar’ unit for installations where the signal from one TWL01 LNB is
combined with a DTT signal and converted into a 1310/1550nm Fibre Optical signal.
Several TOU232-SA standalone units can be combined via an active splitter (TAS04) for more than 2x32 fibre
outputs. To realize such a system you need to use 1 x TOU232-Kit (including the TWL01 LNB) for the first full
installation, 1 x TAS04 Active Splitter and 1 x TOU232SA for every additional output out of the TAS04 you
want to use. This gives you a possible total of 128, 192 or 256 optical outputs.
NOTE: the 2 meter High Frequency RF-cable, TUC001, to connect the TAS04 splitter with the Sidecar, is NOT
included in this part number. It must also be purchased as a separate item for every additional SideCar unit
used.
Rev. 1.0, 10-2011, JNY
TOU232-Kit, Fibre Optical LNB, 307614
Page 7
For specifications, see TOU232-Kit
Rev. 1.0, 10-2011, JNY
TOU232-Kit, Fibre Optical LNB, 307614
Page 8
High Frequency, Hich Quality RF cable
w/ pre-fitted N-connectors
TUC Series
TUC001
2 meters, P/N: 307617
TUC004
4 meters, P/N: 3076xx
General description:
The TUC001, included as a single item in the TOU232-Kit, can also be purchased separately. This is
needed in the event a larger system is built using a TAS04 Active Splitter, to extend the number of
optical outputs from 2 x 32 to at total of 128, 192 or 256.
The TUC001 High Quality, High Frequency RF cable comes with pre-fitted N-connectors and must not
be changed in length. This is because the cable must accurately match the high frequency loss
involved in the frequency stacked broadband output of a TWL01 LNB as compensated in the Sidecar
unit. For this reason NEVER use a home-made cable for this use – you’ll get a bad frequency
response in case you do!
Normally the TUC001 included in the TOU232-Kit is used to connect the TWL01 LNB to the Sidecar. If
you want to extend the system with an Active Splitter you need to purchase 1 x TAS04 Active Splitter
and as many TUC01 cables you need, to connect to the number of outputs out of the TAS04 you
want to use (you also need to buy 1, 2 or 3 extra TOU232-SA Sidecars)
Rev. 1.0, 10-2011, JNY
TOU232-Kit, Fibre Optical LNB, 307614
Page 9
For specifications, see TOU232-Kit
Rev. 1.0, 10-2011, JNY
TOU232-Kit, Fibre Optical LNB, 307614
Page 10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising