carmel 48” ceiling fan
CARMEL 48” CEILING FAN
MODELS #50196, 50197
Español p. 21
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-877-361-3883, Monday - Thursday, 8 am - 6 pm, EST and Friday,
8 am - 5 pm, EST.
WELCOME
TABLE OF CONTENTS
PREPARATION
Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . 2
Before beginning the assembly of this product, ensure
that all parts are present. Compare all parts with the
package contents list and hardware contents list. If
any part is missing or damaged, do not attempt to
assemble the product.
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Mounting Options . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
After opening the top of the carton, remove the
mounting hardware package from the foam inserts,
then remove the motor from the packaging and
place it on a soft surface, such as a carpet, to avoid
damage to the finish.
Mounting Bracket Installation . . . . . . . . . . . . . . . . . . 6
Standard or Angle Mounting Instructions . . . . . . .7
Closemount Instructions . . . . . . . . . . . . . . . . . . . . . 10
Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Estimated Assembly Time: Under 60 minutes
Canopy Installation . . . . . . . . . . . . . . . . . . . . . . . . . 12
Tools Required for Assembly (not included): Electrical
Tape, Phillips Screwdriver, Pliers, Safety Glasses,
Step Ladder, and Wire Strippers
Blade Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Light Kit Installation . . . . . . . . . . . . . . . . . . . . . . . . . 14
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . 16
Helpful Tools (not included): AC Tester Light, Tape
Measure, Wiring Handbook, and Wire Cutters
Replacement Parts List . . . . . . . . . . . . . . . . . . . . . . 18
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
CARE AND MAINTENANCE
Limited Lifetime Warranty . . . . . . . . . . . . . . . . . . . . 20
At least twice each year, lower the canopy to check
the downrod assembly, and then tighten all screws
on the fan. Clean the motor housing with only a soft
brush or lint-free cloth to avoid scratching the finish.
Clean the blades with a lint-free cloth. You may
occasionally apply a light coat of furniture polish to
wood blades for added protection.
ATTACH YOUR RECEIPT HERE
Important: Shut off the main power supply before you
begin any maintenance tasks. Do not use water or a
damp cloth to clean the ceiling fan.
FAN WEIGHT
Serial Number
The net weight of this fan is: 17.6 lbs. (8,0 kg).
Purchase Date
2
PACKAGE CONTENTS
Unpack your fan and check the contents. You
should have the following items:
2
1
10
5
3
1.Canopy
2.Mounting Bracket
3.Canopy Cover
4.Blades (5)
5.Downrod
6.Blade Arm (5)
7. Bulb (3)
8. Receiver
9. Remote Control
10.Yoke Cover
11. Motor Assembly
12.Light Kit
13. Glass Globe
14. Switch Housing
15.Switch Housing Cover
16. Loose parts bags containing (not shown):
Mounting hardware, blade attachment
hardware, electrical hardware and wire
connectors, etc.
11
6
12
7
13
4
8
9
14
15
3
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate, or install the product.
• Before you begin installing the fan, disconnect the power by removing fuses or turning off the
circuit breakers.
• Make sure that all electrical connections comply with local codes, ordinances, the National Electrical
Code, and ANSI/NFPA 70-199. Hire a qualified electrician or consult a do-it-yourself wiring handbook if
you are unfamiliar with installing electrical wiring.
• Make sure the installation site you choose allows a minimum clearance of 7 ft. from the blades to the
floor and at least 30 in. from the end of the blades to any obstruction.
!
DANGER
!
! WARNING !
When using an existing outlet box, make sure
the outlet box is securely attached to the building
structure and can support the full weight of
the fan. Failure to do this can result in serious
injury or death. The stability of the outlet box is
essential in minimizing wobble and noise in the
fan after installation is complete.
To reduce the risk of fire, electric shock, or personal
injury, mount the fan to an outlet box marked
“ACCEPTABLE FOR FAN SUPPORT” and use the
mounting screws provided with the outlet box. Most
outlet boxes commonly used for the support of
lighting fixtures are not acceptable for fan support
and may need to be replaced. Consult a qualified
electrician if in doubt. Secure the outlet box directly
to the building structure. The outlet box and its
support must be able to support the moving weight
of the fan (at least 35 lbs.). Do NOT use a plastic
outlet box.
! WARNING !
To reduce the risk of fire or electric shock, do not
use the fan with any solid-state speed-control
device or control the fan speed with a full-range
dimmer switch.
! WARNING !
!
CAUTION
!
CAUTION
!
Be sure the outlet box is properly grounded or
that a ground (green or bare) wire is present.
To reduce the risk of fire, electric shock, or
personal injury, do not bend the blade arms
when installing them, balancing the blades, or
cleaning the fan. Do not insert objects between
the rotating fan blades.
!
Read all instructions and safety information
before installing your new fan. Review the
accompanying assembly diagrams.
4
MOUNTING OPTIONS
!
DANGER
Fig. 1
!
Turn off the circuit breakers and the wall switch to
the fan supply line leads. Failure to disconnect
the power supply prior to installation may result in
serious injury or death.
1. Your fan has 3 mounting options:
• Standard (Fig. 1)
• Angled (Fig. 2)
• Closemount (Fig. 3)
Note: The fans in figures 1 through 3 are not the actual
fan in your package, they are representation of the
3 different mounting options.
Fig. 2
Important: If using the angle mount, check to ensure
the ceiling angle is not steeper than 10°.
Helpful Hint: Standard mounting is best suited for
ceilings 8 ft. or higher. For taller ceilings you may
want to use a longer downrod (sold separately).
Angled mounting is best suited for angled or
vaulted ceilings. A longer downrod is sometimes
necessary to ensure proper blade clearance.
Closemount-style mounting is more suitable for
ceilings lower than 8 ft. (2,44 m) high.
2. Ensure that the blades of the fan are 30 in. (76 cm)
from any obstruction.
Fig. 3
3. Check the downrod length to ensure the blades will
be at least 7 ft. (2,14 m) above your floor.
5
MOUNTING BRACKET INSTALLATION
4. Remove the two mounting bracket screws and
washers from the round holes in the canopy and
loosen the other two screws. Set aside for later
use. Detach mounting bracket from canopy (Fig. 4).
Mounting Bracket
Screw
Fig. 4
Mounting
Bracket
Screws
Washer
Washer
Canopy
5. Secure the mounting bracket to the outlet box using
screws and washers provided with the outlet box
(not included) (Fig. 5).
Fig. 5
Note: It is very important that you use proper hardware
when installing the mounting bracket as it supports
the fan.
Important: If using the angle mount, ensure that the
open end of the mounting bracket is installed facing
the peak of the ceiling.
6
Mounting
Bracket
STANDARD OR ANGLE MOUNTING INSTRUCTIONS
6. Partially loosen the motor housing set screws in the
yoke at the top of the motor housing (Fig. 6).
Fig. 6
Set Screw
7. Remove the downrod pin and downrod clip from
the downrod (Fig. 7).
Fig. 7
Downrod
Clip
Downrod Pin
Downrod
Pin
Downrod Clip
Fig. 8
8. Thread the wires from the motor assembly through
the yoke cover, canopy and out the top of the
downrod (Fig. 8).
Downrod
Canopy
Yoke
Cover
7
Motor
Assembly
STANDARD OR ANGLE MOUNTING INSTRUCTIONS
9. Slide the downrod into the yoke of the motor
assembly, align the holes, and re-install the
downrod pin and downrod clip. Then re-tighten the
set screws (Fig. 9).
Fig. 9
Downrod
Pin
Downrod Pin
Set Screw
Downrod Clip
10. Depending on the length of downrod you use, you
may need to cut the lead wires back to simplify the
wiring. If you decide to cut back the lead wires,
it is suggested that you do so in the following
manner: Take the lead wires and make sure that
you have pulled them all the way through the top
of the downrod and measure 8 in. of lead wire, and
then cut the excess wire off with wire cutters (not
included) (Fig. 10).
Fig. 10
11. If you cut back the lead wire in Step 10, strip 1/2
in. of insulation from the end of each wire. Twist
the stripped ends of each strand of wire within the
insulation with pliers (not included) (Fig. 11).
Fig. 11
Cut Wires
Stripped
Wires
Note: If you did not cut back the lead wires in Step 10,
Step 11 is not necessary and you may proceed to
Step 12 instead.
8
Downrod
Downrod
Clip
STANDARD OR ANGLE MOUNTING INSTRUCTIONS
12. Install the ball end of the downrod into the
mounting bracket opening. Align the slot in the
ball with the tab in the mounting bracket. The rod
should not rotate if installed correctly (Fig. 12).
Fig. 12
Mounting
Bracket
Downrod
Ball
13. Insert the receiver into the mounting bracket with
the flat side toward the ceiling (Fig. 13).
Fig. 13
Receiver
Mounting
Bracket
9
CLOSEMOUNT INSTRUCTIONS
14. Remove the canopy cover from the bottom of the
canopy (Fig. 14).
Fig. 14
Helpful Hint: Closemount mounting is more suitable
for ceilings lower than 8 ft. (2,44 m) high. The
downrod, hanging ball, and canopy cover are not
used in this type of installation.
Canopy
Cover
15. Align the canopy with the closemount screw
holes in the top of the motor assembly. Secure
the canopy to the top of the motor assembly by
installing three closemount screws and spring
washers into the top of the motor housing (Fig. 15).
Closemount Screw
Fig. 15
Canopy
Closemount
Screws
Spring
Washer
Spring Washer
Fig. 16
16. Raise the fan and place the canopy on the
mounting bracket hook for wiring. Insert the
receiver into the mounting bracket with the flat side
facing the ceiling (Fig. 16).
Ceiling
Hook
Canopy
Receiver
10
WIRING
!
CAUTION
Fig. 17
!
Be sure outlet box is properly grounded or that a
ground (green or bare) wire is present.
White (neutral)
Bare/Green (ground)
White
Red
If house wires are different colors than referred to in
the following step, stop immediately. A professional
electrician is recommended to determine wiring.
Incorrect wire connection can damage the receiver
and could cause fire or injury.
Green
!
Antenna
Blue
17. Connect supply, receiver, and fan wires according
to the diagram (Fig. 17) and these steps:
ck
Bla lue
B
White
• Connect the Green wires from the fan and
mounting bracket to the Bare/Green (ground)
supply wire.
Receiver
te
hi
W
• Connect the Blue wire from the receiver to the Blue
fan wire.
• Connect the Black wire from the receiver to the
Black fan wire.
• Connect the Red wire from the receiver to the
Black (hot/power) supply wire.
• Connect the White wire with the red label from the
receiver to the White (neutral) supply wire.
• Connect the White wire with the white label from
the receiver to the White fan wire.
Secure all wiring connections together with wire
connectors and push all connected wires back into
the outlet box.
Important: The black fan wire is power for fan. The blue
fan wire is power for the light. The white wire from
the fan is common/neutral. The green wires from the
fan and mounting bracket are ground wires.
Wire Connector
11
Gre
en
!
a
WARNING
Black (hot/power)
CANOPY INSTALLATION
18. Lift the canopy up so the partially installed mounting
bracket screws are situated in the L-slots on each
side of the canopy. Rotate the canopy clockwise
and install the remaining mounting bracket screws
and washers removed in Step 4 (Fig. 18).
Fig. 18
Canopy
Mounting Bracket
Screw
Washer
12
Mounting
Bracket
Mounting
Bracket
Screw and
Washer
BLADE INSTALLATION
20. Partially insert three blade screws along with three
blade washers through one blade and into one
blade arm. Tighten each blade screw with a Phillips
screwdriver, starting with the one in the middle.
Repeat this step for the remaining blades and
blade arms (Fig. 20).
Blade Screw
Fig. 19
Blade Screw
Washer
Blade
Blade Arm
Washer
20. Insert blade arm through slots in the side of the
motor assembly. Align the holes of one blade arm
with two motor screw holes in underside of the motor
assembly. Secure with two motor screws. Repeat
this step for the remaining blade arms (Fig. 20).
Fig. 20
Blade Arm
Motor Screw
Blade
Motor Screw
13
LIGHT KIT INSTALLATION
21. Remove two of the four fitter plate screws
located on the underside of the motor assembly
and loosen the other two screws. Align the two
key slots of the light kit with the loosened fitter
plate screws. Rotate the light kit clockwise until
the screw heads engage the key slots. Replace
previously removed fitter plate screws, then tighten
all screws (Fig. 21).
Fig. 21
Fitter Plate
Screw
Light Kit
22. Remove the four switch housing cover screws
preassembled to the switch housing. Set aside for
later (Fig. 22).
Fig. 22
Fitter Plate
Screws
Switch Housing
Switch Housing
Cover Screw
Switch Housing
Cover Screws
23. Remove the four switch housing screws
preassembled to the light kit. Secure the switch
housing to the light kit by re-installing the switch
housing screws (Fig. 23).
Fig. 23
Note: The switch housing should be oriented so its
notch covers the wiring from the light kit.
Notch
Light
Kit
Switch
Housing
Switch Housing
Screw
14
Switch
Housing
Screw
LIGHT KIT INSTALLATION
24. Connect the two 4-pin connectors and two 9-pin
connectors from the switch housing. Insert the
connectors into the switch housing. Then, install
the switch housing cover to the switch housing
using the switch housing cover screws that were
previously removed (Fig. 24).
Fig. 24
Switch Housing
Cover Screw
Switch
Housing
Cover
Switch Housing
Cover Screw
25. Install bulbs (Fig. 25).
Fig. 25
Important: When replacing the bulb, allow bulb and
light kit to cool before touching.
Bulb
26. Lift the glass globe up to the light kit and twist tightly
in a clockwise direction until it is secure (Fig. 26).
Fig. 26
Glass Globe
15
OPERATING INSTRUCTIONS
27. Use the fan reverse switch, located on the side
of the light kit, to optimize your fan for seasonal
performance (Fig. 27).
Fig. 27
Using a ceiling fan will allow you to raise your
thermostat in the summer and lower your
thermostat in the winter without sacrificing comfort.
Important: Wait for the fan to stop before moving the
reverse switch. The reverse switch must be set
either completely left or right in order for the fan to
function correctly. If the reverse switch is set in the
middle position, the fan will not operate.
Reverse Switch
28. In warmer weather, push the reverse switch left,
which will result in downward airflow creating a
wind chill effect (Fig. 28).
Fig. 28
Note: Energy savings are possible by turning on the
ceiling fan and setting the thermostat a few degrees
warmer. To maximize savings, turn ceiling fan off
when no one is in the room.
29. In cooler weather, push the reverse switch right
and the fan to low, which will result in upward airflow
that can help move stagnant, hot air off the ceiling
area. By mixing the air, the heat may not have to run
as often and may yield energy savings (Fig. 29).
Fig. 29
16
OPERATING INSTRUCTIONS
30. Remove the battery cover from the back of the
remote (Fig. 30). After removing the protective
plastic, insert the battery. Replace the battery cover.
Fig. 30
D/CFL Switch: Located inside the battery
compartment of the remote, this switch should
be moved to either “D” for dimmer or “CFL” for
compact fluorescent bulbs depending on which
type of bulbs you’ve installed in the fan.
Note: The switch is pre-set to “CFL”. Move the switch
to “D” to correspond with the included incandescent
bulbs which will enable the dimming function.
Important: The dimmer function does not work with
CFL bulbs.
Remote
D/CFL Switch
Battery
Battery
Compartment
31. To operate the fan using the remote, press and
release the following buttons (Fig 31):
Fig. 31
1
2
3
4
1 - High fan speed
2 - Medium fan speed
3 - Low fan speed
4 - Power - Turns the fan off.
Light Delay Off mode - Press and hold the power
button (4) for five seconds, which will turn off light
after one minute. The LED indicator on the remote
will flash four times to confirm mode setting.
5
Remote
Control
5 - Light Control - Press button to turn lights off and
on (all bulbs). Press and hold light control to dim or
brighten the lights (incandescent bulbs only).
17
Battery Cover
REPLACEMENT PARTS LIST
For replacement parts, call the customer service department at 1-877-361-3883, 8 a.m. - 6 p.m., EST, Monday Thursday, 8 a.m. - 5 p.m., EST, Friday.
PIECE
DESCRIPTION
MODEL 50196 MODEL 50197
PART #
PART #
50196-A
50197-A
50196-B
50197-B
50196-C
50197-C
A
B
C
Glass Globe
Blade Arm
Blade
D
Loose parts bags containing
(not shown): Mounting
hardware, blade attachment
hardware, electrical hardware
and wire connectors, etc.
50196-D
50197-D
Remote Control Pack
50196-E
50197-E
E
A
B
C
E
18
TROUBLESHOOTING
At least twice each year, lower the canopy to check the downrod assembly, and then tighten all screws
on the fan. Clean the motor housing with only a soft brush or lint-free cloth to avoid scratching the finish.
Clean the blades with a lint-free cloth. You may occasionally apply a light coat of furniture polish to wood
blades for added protection.
Important: Shut off the main power supply before you begin any maintenance tasks. Do not use water or
a damp cloth to clean the ceiling fan.
Problem: The fan does not move
1. Turn the power on or check the fuse.
2. Turn the power off. Loosen the canopy and check all connections.
3. Check that the connectors from the light kit fitter and fan are connected properly.
4. Disable the power supply to the fan motor and re-start the motor.
5. The blade is overweight. Do not install the unapproved blades.
Problem: The fan is noisy.
1. Check and tighten all screws that hold the fan blades to the blade arms and the motor.
2. Replace the cracked blade.
Problem: There is excessive wobbling
1. Check and tighten all screws that hold the fan blades to the blade arms and the blade arms to the motor.
2. Switch one blade with a blade from the opposite side or balance the fan using a balancing kit.
3. Turn off the power. Loosen the canopy and verify that the mounting bracket is secure to the
electrical outlet box.
4. The bracket must be flush without movement against the outlet box.
Problem: The fan operates correctly, but the lights are not working (if applicable).
1. Re-install the bulb(s).
2. Ensure that the male and female plugs in the light kit fitter are connected properly.
3. Turn the power off and check all connections at the ceiling outlet box.
4. Check to see if the light is over than 190W, since a limiter included.
Problem: The remote control doesn’t work.
1. Replace the remote battery with a 23A, 12-volt battery.
2. To re-sync remote to fan - Press and hold the high and low speed buttons on the remote control at the
same time for 5 seconds. The LED indicator will flash 3 times. When syncing is complete, the fan will start
on the low speed with the light (if applicable) off.
19
LIMITED LIFETIME WARRANTY
Subject to the limitations set forth below, Hong Kong China Electric appliance Company (HKC) warrants the fan
motor for this ceiling fan to be free from defects in workmanship and material for the life of the product. Also,
subject to the limitations below, HKC warrants all ceiling fan parts (“ceiling fan parts” excludes the motor and parts
made in whole or in part with glass) to be free from defects in workmanship and material for a period of one year
after the date of purchase by the original purchaser at retail.
All claims must be made by the original purchaser, whether such purchaser purchased the product through a store
or contractor. Ceiling fan part defects must be reported within the first year from the date of purchase. Parts made in
whole or in part with glass and the finishes of metal and other surfaces are not warranted.
Purchasers are responsible for all costs of removing and reinstalling the product. Any damage to any part caused
by ordinary wear and tear, accident, misuse, or improper installation, is not covered by this warranty. HKC
assumes no responsibility whatsoever for fan installation. Any service performed by a non-licensed electrician will
render the warranty invalid.
HKC’s sole responsibility shall be to repair or replace the motor, parts, or product within the terms stated above.
HKC SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL
OR CONSEQUENTIAL DAMAGES RESULTING DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF
WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. SOME STATES DO
NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THIS
LIMITATION MAY NOT APPLY TO YOU. IF THE ORIGINAL PURCHASER CEASES TO OWN THE FAN, THIS
WARRANTY IS VOIDED.
Should the purchaser encounter a problem with your fan related to defects in workmanship or materials within the
warranty period associated with the defective part, HKC agrees to replace the defective part without charge, or at
its option, to replace the ceiling fan with a comparable or superior model.
HKC’S WARRANTIES ARE LIMITED TO THE WRITTEN WARRANTIES SET OUT IN THIS HKC CEILING
FAN LIMITED LIFETIME WARRANTY. ALL OTHER EXPRESS AND IMPLIED WARRANTIES, INCLUDING,
WITHOUT LIMITATION, THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND THE
IMPLIED WARRANTY OF MERCHANTABILITY ARE DISCLAIMED. SOME STATES DO NOT ALLOW THE
DISCLAIMER OF IMPLIED WARRANTIES, SO THIS DISCLAIMER MAY NOT APPLY TO YOU.
To obtain warranty service, please write down your model number and call Customer Service at
1-877-361-3883 Monday - Thursday, 8 am - 6 pm, EST and Friday, 8 am - 5 pm, EST. Please have a copy of the
receipt as proof of purchase.
The Honeywell Trademark is used under license from Honeywell International
Inc. Honeywell International Inc. makes no representations or warranties with
respect to this product. This product is manufactured for:
9076-EN
Hong Kong China Electric Appliance Manufacture Co., Ltd.
3059 Forest Hill Irene Rd, Suite 103
Germantown, TN 38138
1-877-361-3883
20
r060414
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising