E1/T1/J1 PRI Card

E1/T1/J1 PRI Card
2nd Generation E1/T1 PRI Card Installation
E1/T1/J1 PRI Card
Second Generation
Quick Installation Guide
Version 1.0
2
Quick Installation Guide v1.0
www.cem-solution.net
2nd Generation E1/T1 PRI Card Installation
Table of Contents
Hardware Setup: ...................................................................................................... 4
Software Installation Steps: ..................................................................................... 5
Software Configurations: ......................................................................................... 7
3
Quick Installation Guide v1.0
www.cem-solution.net
2nd Generation E1/T1 PRI Card Installation
Hardware Setup
1) Customization of the Second gen PRI card to use in PCI / PCIe server slot.
2) Insert the Second Gen 4 port PRI (PCI/PCIe) card in the corresponding PCI/PCIe slot
of the Server.
3) Check if the installed PRI card is detected using the below command
# lspci
If the card has been recognized, it will be displayed in the output information.
Note: If the PRI card is not recognized by the system, you have to power off and
take out the card, and then insert it into another PCI-E slot.
4
Quick Installation Guide v1.0
www.cem-solution.net
2nd Generation E1/T1 PRI Card Installation
Software Installation Steps:
Test Environment
Libpri-1.4.14
dahdi-linux-complete-2.7.0
asterisk-11.4.0
centos 6.2 (kernel version: 2.6.32)
Installation of Pre requistic packages:
Install all of Asterisk’s dependencies that are required to compile asterisk.
Run the followings commands to install the required packages needed for compiling drivers
from source.
[root@localhost ~]# yum install bison bison-devel ncurses ncurses-devel zlib zlibdevel openssl openssl-devel gnutls-devel gcc gcc-c++ libxml2
Installation of Libpri package
Go to /usr/src directory and Download libpri by running the following command
[root@localhost src]# wget http://downloads.asterisk.org/pub/telephony/libpri/libpri1.4.14.tar.gz
After downloading LibPri extract the LibPri tar file by the command
[root@localhost src]# tar -xvzf libpri-1.4.14.tar.gz
Install the LibPri by following the commands
[root@localhost src]# cd libpri-1.4.14
# make clean
# make
#make install
Installation of Dahdi Driver
Download the DAHDI driver with tools, which are available at
http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete/
Download latest Dahdi Driver ( Dahdi 2.7.0) from the using the following command
#wget http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete/dahdi-linuxcomplete-2.7.0+2.7.0.tar.gz
Extract the downloaded file and enter into that directory
# tar -xvzf dahdi-linux-complete-2.7.0+2.7.0.tar.gz
5
Quick Installation Guide v1.0
www.cem-solution.net
2nd Generation E1/T1 PRI Card Installation
Use the following commands to install DAHDI drivers
# cd dahdi-linux-complete-2.7.0+2.7.0
#make
#make install
#make config
Successful Dahdi Driver installation shows the similar output & list the detected
Dahdi devices
Installation of Asterisk:
Download the latest version of asterisk. Asterisk is available for download from:
http://downloads.asterisk.org/pub/telephony/asterisk/
After downloading asterisk, extract the asterisk tar file by giving following command.
#wget http://downloads.asterisk.org/pub/telephony/asterisk/asterisk-11-current.tar.gz
Go to asterisk folder and compile the packages as shown in the screenshot
To install asterisk give the following commands:
[root@pbx1 asterisk-11.4.0]# ./configure
#make
# make install
# make config
6
Quick Installation Guide v1.0
www.cem-solution.net
2nd Generation E1/T1 PRI Card Installation
If this is your first Asterisk Install, you should install the sample configuration files, to
do this run:
# make samples
Software Configurations:
After compiling and installing DAHDI and Asterisk, load the Dahdi driver by running:
# /etc/init.d/dahdi start
# dahdi_genconf –vvv
If there is any error, please trace the cause. Until all errors are clear up, you should
execute "dahdi_genconf" again, and then go to the next step.
By running "dahdi_genconf", it will generate /etc/dahdi/system.conf and
etc/asterisk/dahdi-channels.conf automatically. Checking whether the generated files
information agrees with your hardware setup, if not, you should modify to your
specific requirements.
Do not forget to confirm dahdi-channels.conf is included in chan_dahdi.conf to
configure dahdi channels with asterisk, if not, run command:
# echo "#include dahdi-channels.conf" >> /etc/asterisk/chan_dahdi.conf
Execute the following command:
# dahdi_cfg –vvvvvv
This command is used for reading and loading parameters in the configuration file
system.conf and writing to the hardware.
Start the Asterisk by executing
# asterisk –gvvvvvvvvvc
Makesure that PRI spans are up and active, before making calls.Here is the
command to check the pri span status
CLI> pri show spans
7
Quick Installation Guide v1.0
www.cem-solution.net
2nd Generation E1/T1 PRI Card Installation
If you face any issues, please contact the reseller from whom you have
purchased the CEM product or submit a support ticket http://support.allo.com/
Thank You for choosing CEM Solutions!
8
Quick Installation Guide v1.0
www.cem-solution.net
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising