NUSP instruction.qxd

NUSP instruction.qxd
Installation Instructions
NUSP
****URGENT: READ PRIOR TO ATTEMPTING INSTALLATION***
DIRECT WIRE MODULE INSTALLATION INSTRUCTIONS
For use with NORA NULS Series Fluorescent Under Cabinet Fixtures
This Direct Wire Module is to be used only with NULS Series Under Cabinet Luminaires. This Module is
designed to be wired using Non-Metallic Cable (NM), or Armored Cable (BX). When using Romex, proper
grounding of the electrical connector must be maintained.
NOTE: ELECTRICAL CONNECTOR FOR YOUR WIRING TYPE MUST BE PURCHASED SEPARATELY.
IMPORTANT SAFETY INSTRUCTIONS
1. Read all instructions before beginning installation.
Safely store these instructions for future reference.
2. TO BE INSTALLED BY QUALIFIED ELECTRICIANS ONLY, THE
d. ALL OPEN ELECTRICAL PORTS ON MODULE AND
CONNECTORS HAVE BEEN COVERED WITH ELECTRICAL
PORT COVERS.
INSTALLATION MUST BE MADE IN ACCORDANCE WITH THE
8. WARNING: TO PREVENT OVERHEATING, DO NOT INSTALL
CURRENT EDITION OF THE NATIONAL ELECTRIC CODE AND
IN SMALL ENCLOSED SPACES. TO PREVENT ELECTRICAL
ALL APPLICABLE STATE AND LOCAL BUILDING CODES.
SHOCK, DO NOT INSTALL IN WET ENVIRONMENTS.
3. This module is only for use with NULS Series luminaires and
accessories. Do not use this module, jumper cord or
connector to provide power to other products.
4. WARNING: WHEN MULTIPLE FIXTURES ARE CONNECTED
9. DO NOT USE DIMMERS with NULS Series Fluorescent
Under Cabinet fixtures.
10. Always disconnect electrical power from this product before
cleaning or putting on or taking off parts.
TOGETHER, BE SURE THEY ARE CONNECTED TO BRANCH
11. Do not operate product if jumper cord has been damaged.
CIRCUIT AT ONLY ONE FEED POINT.
12. Keep jumper cord away from sources of heat and heated surfaces.
5. CAUTION: Do not exceed 7 AMPS maximum load.
6. For use with 120V 60Hz power supply only. For interior use only.
13. Do not operate this product in environments where aerosol
sprays are being used or where oxygen is being administered.
7. WARNING: DO NOT ELECTRIFY THE MODULE UNTIL THE
FOLLOWING CONDITIONS HAVE BEEN MET:
a. MOUNTING AND WIRING OF MODULE IS COMPLETE.
b. THE MODULE COVER HAS BEEN REPLACED AND SCREWS
SECURELY FASTENED.
c. ALL FIXTURES CONNECTED TO MODULE HAVE BEEN
MOUNTED AND THEIR DIFFUSERS / LENSES HAVE BEEN
PROPERLY RE-INSTALLED.
SAVE THESE INSTRUCTIONS
6505 Gayhart St., Commerce, CA 90040
www.NoraLighting.com
Installation Instructions
NUSP
****URGENT: READ PRIOR TO ATTEMPTING INSTALLATION***
DIRECT WIRE MODULE INSTALLATION INSTRUCTIONS
For use with NORA NULS Series Fluorescent Under Cabinet Fixtures
NUSP DIRECT WIRE MODULE INSTALLATION
DIRECT WIRE MODULE
Electrical Port Cover
NOTE: ELECTRICAL CONNECTOR FOR YOUR WIRING
TYPE MUST BE PURCHASED SEPARATELY.
1. Turn off power for appropriate electrical circuit at electrical
service panel.
2. Remove module cover screws and remove cover.
3. Depending on your particular application you may affix electrical
connector fitting first to electrical supply (NM or BX) or affix
fitting first to large hole in rear of module. In either case there
should be approximately 2-1/2" of wires available for electrical
connection. The end of these should be stripped 1/2". Shorten or
lengthen the wire leads and strip the ends as needed.
4. For Non-Metallic Cable (NM) installations, the grounding
ring must be used. The ring should be positioned inside the
module and be underneath the locknut of the electrical connector
fitting. Locknut must be tightened securely.
5. Pushed stripped ends of wires into hole in wire trap connectors
(see WIRING DIAGRAM). Note that black supply wire goes into
connector with black wire and white wire goes into connector
with white wire. If grounding ring is used (as in the case with NM
supply wires) twist together the bare ground wire from the NM
and the ground wire from the grounding ring.
6. Tighten locknut and clamping screw(s) on electrical connector
fitting securely.
7. Push excess electrical supply wire back into the wall and locate
wiring module on mounting surface.
8. Affix module to underside of cabinet with screws provided.
Be careful not to drive screws all the way through the cabinet
bottom. If necessary, use shorter screws.
9. Replace and secure wiring module cover with supplied screws.
10. Follow installation instructions provided with under cabinet
luminaires. Mount luminaires, remove electrical port cover
and insert jumper cord (supplied with module) into electrical port.
11. Make sure all luminaires connected to the module have their
diffusers/lenses properly installed and that all open electrical
ports on the module and luminaires are safely covered with
electrical port covers.
12. Restore circuit power at electrical service panel. Turn on switches
on each individual luminaire.
Electrical Port
Module Cover
Mounting Screws
Grounding Ring
and Wire Nut
Used for Romex
(NM) Applications
Jumper Cord
Self -Adhesive Cable Clips
Use to organize/secure Jumper Cord
WIRING DIAGRAM
Electrical Connector
(purchased separately)
Armored Cable
Supply Wire (BX)
Non Metallic
Supply Wire (NM)
Requires use of
Grounding Ring
Wire Trap Connectors
6505 Gayhart St., Commerce, CA 90040
www.NoraLighting.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising