Adapters and adapter cables for SQuadriga II

Adapters and adapter cables for SQuadriga II
HEAD
DD
ata
Sheet
atenblatt
Ebertstraße 30a
52134 Herzogenrath
Tel.: +49 2407 577-0
Fax: +49 2407 577-99
eMail: info@head-acoustics.de
Web: www.head-acoustics.de
Adapters and adapter cables for
SQuadriga II
Overview
The functionality of SQuadriga II
can be significantly expanded via the
Aux 1 and Aux 2 interfaces. Different
adapters and cables are available to
record CAN, OBD-2 or GPS signals, to put out pulses and to record
artificial head signals. Furthermore, a
programmable equalizer PEQ V or a
binaural USB front-end BEQ II can be
connected and/or a SQuadriga II can
be integrated into a HEADlab system.
Beyond that it is possible to expand
SQuadriga II with a signal module
labV6/labVF6 or to form a system
with several SQuadriga II devices.
The adapters are equipped with active
electronics.
The use of the firmware 1.4 is recommended.
Aux 1 interface
CAN bus adapter
CLD VII.1 (Code 3351)
Pulse out adapter CLB VII.4 (Code 3354)
RS232 adapter CLD VII.8 (Code 3358)
The CAN bus adapter CLD VII.1 connects SQuadriga II with the secondary
CAN interface of a vehicle.
·· Acquisition of CAN bus data e.g.
speed, RPM, position of the driver’s
accelerator
·· Acquisition of OBD-2 sig­nals according to ISO 15765-4 via cable
CDO X.xx (Code 3786)
·· Electrical isolation
The two-channel pulse out adapter
CLB VII.4 is used for the output of
pulses.
·· Loop through of pulses recorded via
the pulse inputs
·· Output of pulses from the SD card
in stand-alone-mode
·· TTL compatible pulse outputs
·· Electrical isolation between the
ground of SQuadriga II and the
ground potential of the two pulse
outputs
The RS232 adapter CLB VII.8 allows
the configuration of an artificial head
(HMS III or HMS IV generation).
To perform an artificial head recording the AES/EBU adapter cable
CLX VII.2 is required.
07.2012 SQuadriga II adapters
Subject to change
·· Adjustment of the acquisition parameters
·· Electrical isolation
·· An RS232 cable CAB I.xx (Code
5475) is additionally required
·· Required for stand-alone mode
Aux 1 interface
Aux 2 interface
GPS-Adapter CLG VII (Code 3357)
HEADlab adapter CLD VII.6 (Code 3356)
ADAT adapter CLA VII.5 (Code 3355)
The GPS adapter CLG VII allows
recordings of GPS coordinates, speed
information etc. with SQuadriga II.
The information are stored in a channel.
The HEADlab adapter CLD VII.6 is
used to integrate SQuadriga II as a
signal module into a HEADlab system
or to expand SQuadriga II as a controller with a HEADlab module labV6
or labVF6.
·· For use in a HEADlab system the
cable CLL X.xx (Code 3780-xx) is
additionally required
·· For use with a signal module the
cable CLL X.xx (Code 3780-xx), a
power box labPWR I.1 (Code 3711)
and the cable CLL XI.xx (Code
3781-xx) are additionally required
The ADAT adapter CLA VII.5 connects SQuadriga II with a compatible
device such as the programmable
equalizer PEQ V, the binaural USB
front-end BEQ II (as of version C) or a
sound card.
Furthermore, ADAT adapters allow an
electrically isolated connection of two
SQuadriga II. Therefore two additional cables CLW II.xx (Code 9825)
are required.
AES/EBU adapter cable CLX VII.1 (Code 3352-1)
SQuadriga II adapter cable CLL VII.1 (Code 3353-1)
The AES/EBU adapter cable CLX VII.1
allows recordings with a HMS III or a
HMS IV artificial head.
Furthermore, with AES/EBU adapter
cables more than two SQuadriga II
can be connected to a system.
·· Synchronization of several SQuadriga II
·· Electrical isolation of the AES/EBU
inputs and outputs
The SQuadriga II adapter cable
CLL VII.1 allows the connection of two
SQua­driga II devices to a system.
·· Synchronized recordings with up to
eight additional analog channels of
the second SQuadriga II (slave)
·· Different sampling rates for the analog channels of the second SQuadriga II adjustable when writing to
the SD card in stand-alone mode
The adapter has a magnetic mount
on the bottom.
07.2012 SQuadriga II adapters
Subject to change
Technical Data
CAN bus adapter CLD VII.1
Connections:
9-pin DSUB ↔ Lemo 10-pin (Aux 1)
Power supply:
3.3 V (+/- 10%), the power is supplied by SQuadriga II
15 mA, typ.
Electrical isolation:
up to 1 Mbps
Cable length:
1 m (39.4“)
Dimensions, without cable: 90 mm (3.5“) x 60 mm (2.4“) x 23 mm (0.9) (W x D x H)
Weight, without cable: 130 g(0.29 Ib)
Temperature operating:-20°C - 50°C (-4°F - 122°F) (0 - 90% r.h., not condensing)
Temperature storage:-20°C - 70°C (-4°F - 158°F)
Degree of protection:IP43 according to EN60529
Protection class:
CAT III (according to EN61140)
Complies with the requirements of ISO 11898 and ISO 15765-4
Pulse out adapter CLB VII.4
Connections:
2 x BNC ↔ Lemo 10-pin (Aux 1)
Power supply: 3.3 V (+/- 10%), the power is supplied by SQuadriga II
15 mA typ., max. 40 mA
Pulse frequency, max.: 500 kHz
Output voltage: low level: <0.8 V, high level: >2.5 V
(for IOL= -1 mA; IOH=1 mA)
Max. output current:
+/- 4 mA (IOH; IOL)
Output impedance:
250 Ohm
Insulation resistance: min. 1 GOhm
Cable length:
1 m (39.4“)
Dimensions, without cable: 106 mm (4.2“) x 58 mm (2.3“) x 23 mm (0.9) (W x D x H)
Weight, without cable: 130 g(0.29 Ib)
Temperature operating:-20°C - 50°C (-4°F - 122°F) (0 - 90% r.h., not condensing)
Temperature storage:-20°C - 70°C (-4°F - 158°F)
Degree of protection: IP43 according to EN60529
Protection class: CAT III (according to EN61140)
RS232 adapter CLD VII.8
Connections:
DSUB 9-pin male ↔ Lemo 10-pin (Aux 1)
Power supply: 3.3 V (+/- 10%), the power is supplied by SQuadriga II
15 mA typ., max. 40 mA
Baud rate: 9600 Baud
Insulation resistance: min. 1 GOhm
Cable length: 1 m, typ. (39.4“)
Dimensions, without cable::
100 mm (3.9“) x 58 mm (2.3“) x 23 mm (0.9) (W x D x H)
Weight, without cable: 130 g(0.29 Ib)
Temperature operating:-20°C - 50°C (-4°F - 122°F) (0 - 90% r.h., not condensing)
Temperature storage:-20°C - 70°C (-4°F - 158°F)
Degree of protection: IP43 according to EN60529
Protection class: CAT III (according to EN61140)
GPS adapter CLG VII
Connections:
Power supply: Backup battery: Sensitivity: Protocol: 07.2012 SQuadriga II adapters
Lemo 10-pin ↔ Lemo 10-pin (Aux 1)
3.3 V (+/- 10%), the power is supplied by SQuadriga II
Max. 75 mA (45 mA, typ.)
Lithium, 3 V / 5.5 mAh
-159 dBm (operation); -147 dBm (acquisition)
NMEA0183
Subject to change
Acquisition: 45 sec. (cold start); 40 sec. (warm start)
Update rate: 1 sec.
Cable length: 180 cm (70.9“)
Dimensions, without cable: 47 mm (1.85“) x 39 mm (1.53“) x 16 mm (0.63“) (W x D x H)
Weight, without cable: 70 g (0.15 Ib)
Temperature operating:-20°C - 50°C (-4°F - 122°F) (0 - 90% r.h., not condensing)
Temperature storage:-20°C - 70°C (-4°F - 158°F)
Degree of protection: IP54 according to EN60529
Protection class: CAT III (according to EN61140)
HEADlab adapter CLD VII.6
Connections:
Power/HEADlink ↔ Lemo 10-pin (Aux 2)
Power supply:
24 V (15 V – 24 V DC), the power is supplied by labCTRL I.1 / PSH I.4 / labPWR I.1
by labPWR I.1: 24 V: ca. 0.75 A (18 W: 6 W for labV6/ labVF6 + 12 W for SQuadriga II)
by labCTRL I.1: 24 V: ca. 0.5 A (12 W)
Polarity protection power in: up to 30 V DC
Cable length:
30 cm (11.8“)
Dimensions, without cable: 90 mm (3.5“) x 60 mm (2.4“) x 23 mm (0.9) (W x D x H)
Weight, without cable: 130 g(0.29 Ib)
Temperature operating:-20°C - 50°C (-4°F - 122°F) (0 - 85% r.h., not condensing)
Temperature storage:-20°C - 70°C (-4°F - 158°F)
Derating: no derating up to 50°C (122°F)
Degree of protection:IP43 according to EN60529
Protection class: CAT III (according to EN61140)
ADAT adapter CLA VII.5
Connections:
ADAT ↔ Lemo 10-pin (Aux 2)
Power supply:
+3.3 V, the power is supplied by SQuadriga II
Power consumption:
85 mA
Data rate:
max. 15 Mbps, typ. 12.288 Mbps with SQuadriga II
Optical wavelength:
650 nm
Temperature operating:-20°C - 50°C (-4°F - 122°F) (0 - 90% r.h., not condensing)
Temperature storage:-20°C - 70°C (-4°F - 158°F)
Cable length:
30 cm (11.8“)
Dimensions, without cable: 90 mm (3.5“) x 60 mm (2.4“) x 23 mm (0.9) (W x D x H)
Weight, without cable: 130 g(0.29 Ib)
Degree of protection:IP43 according to EN60529
Protection class:
CAT III (according to EN61140)
AES/EBU adapter cable CLX VII.1
Connections:
2 x XLR3 ↔ Lemo 10-pin (Aux 2)
Electrical isolation:
yes
Cable length:
1 m (39.4“)
SQuadriga II adapter cable CLL VII.1
Connections:
Lemo 10-pin (Aux 2) ↔ Lemo 10-pin (Aux 2)
Cable length:
1 m (39.4“)
ADAT is a registered trademark of the Alesis Corporation; Toslink is a registered trademark of the Toshiba Corporation
07.2012 SQuadriga II adapters
Subject to change
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising