canter 3c15 canter euro 5

canter 3c15 canter euro 5
CANTER 3C15
Mass/Dimensions
Model
DIMENSIONS mm
Wheelbase
Overall length
Cabin length
Overall width
Cabin width
Overall height, approx.
Tread
CANTER EURO 5
Vehicle type
Cab type
Mark
Model code
Crew
3C15
Standard, Single
467.672.11
FB83SB4SLEA2
2500
4900
467.677.11
FB83SG4SLEA2
3350
5970
3850
6690
712
711
2825
4365
4735
3325
5085
5535
2950
5570
1613
1995
1995
2180
1640
1500
Front
Rear
713
712
170
1975
3295
3375
2425
3965
4095
750
1140
1480
625
100
1260
1990
Front * / Rear *
1505
1700
2015
485
1520
2035
495
1535
2050
500
1535
515
3500
Front / Rear
Max. GCW
Chassis Payload
CALCULATED PERFORMANCE
Max. speed
Max. gradeability
Min. turning radius (m)
467.675.11
FB83SE4SLEA2
3
Frame height (back of chassis) approx.
Ground clearance, approx.
Cab to rear axle
Cab to frame end
Max. body length
Frame width
Front overhang
Rear overhang (to frame end)
Front axle to beginning of body
Recommended cab to body gap
WEIGHTS kg
Curb weight (kg) *
Max. GVW
467.674.11
FB83SD4SLEA2
1950
2700
7000
1510
km/h
(tan q)%
Curb to curb
wall to wall
1485
1465
1450
12
13,4
13,6
15
136 (final 4,111)
50 (final 4,111)
10,2
10,6
10,8
12,2
* including coolant, oils, 90% fuel, tire fit, tools and 75 kg driver ** calculated maximum value. Should be checked based on installed body and application *** Without speed limiter device (SLD)
Technical specifications
ENGINE
Model
Type
No. of cylinders
Piston displacement
Max. output (EEC)
Max. torque (EEC)
Air cleaner
Alternator
Exhaust gas recirculation (EGR)
Aftertreatment
DRIVE LINE
Clutch
Transmission
Propeller shaft
Final reduction gear
CHASSIS
Front axle
Rear axle
4P10-0AT3
4 stroke, turbo-charged water cooled direct injection diesel engine with intercooler
4 in line
2,998 cm3
107kW (145PS) / 3,500rpm
370Nm / 1,600rpm
Dry type with paper element with snorkel
A.C. 12 Volt, 110 Amp (Opt. A.C.12 Volt, 140 Amp)
Cooled (tube type)
Ceramic Diesel Particulate Filter (DPF)
Model
Type
Facing material
Facing outside dia.
Model
Type
Gear ratio
Model
Type
Model
Type
Ratio
Model
Type
Rating
Model
Type
Rating
Tyre
Wheel
Steering
Brake
Suspension
Service
Front
Rear
Parking
Auxiliary
Type
Front
Rear
Shock absorbers
Frame
Type
Max. section
Fuel tank capacity
Electrical system - batteries
CAB
Construction
Remark: Above information given is based on homologation data November 2008
C3W28
Hydraulic control, Single dry plate
Woven (Asbest free)
275mm
M037S6 (6S420)
6 forward and 1 reverse speed, synchromesh on all gears
5.152 - 3.022 - 1.956 - 1.360 - 1.000 - 0.799, Rev. 4.636
P3
Tubular, forged steal ends
D1H
Single reduction, hypoid gear
4,111
(Opt. 4.444 / 4.875)
F100TM
Reverse Elliot "I" beam
1,950kg
R015T
Full floating type
2,700kg
195/75 R16C 107/105
Single front, dual rear
16 x 5JK - 110 - 6 stud
Left hand drive
Ball nut type with integral type hydraulic power booster, tilt and telescopic column with steering lock
Hydraulic with vacuum servo assistance, dual circuit with Load Sensing proporting Valve at rear wheels
TBC
TBC
Mechanical internal expanding type on drive shaft at rear of transmission
Exaust brake
Semi-elliptic laminated leaf spring with stabilizer on front and rear axle
(Span mm x width mm x thickness mm - No. of leaves)
1200 x 70 x 16 - 2
1250 x 70 x 10 - 3, 18 - 1
Hydraulic double acting telescopic type on front and rear axles
Parallel tapered channel section with reinforcements and crossmembers
190mm x 55mm x 4.5mm ( depth x upper frange x thickness)
80 lts (Opt. FB83SD4SL/E4SL/G4SL :100 lts)
12 Volts, regulated control (100AH-760A(EN))
Tilt type with torsion bar
All steel welded construction
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising