Standard models ST4000DM005
®
SATA Product Manual
Standard models
ST4000DM005
100804656, Rev. A
August 2016
Document Revision History
Revision
Date
Rev. A
08/31/2016
Description of Change
Initial release.
© 2016 Seagate Technology LLC. All rights reserved.
Publication number: 100804656, Rev. A August 2016
Seagate, Seagate Technology and the Spiral logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. BarraCuda and SeaTools are either
trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. All other trademarks or registered trademarks are the property of their respective owners.
No part of this publication may be reproduced in any form without written permission of Seagate Technology LLC.
Call 877-PUB-TEK1(877-782-8351) to request permission.
When referring to drive capacity, one gigabyte, or GB, equals one billion bytes and one terabyte, or TB, equals one trillion bytes. Your computer’s operating system may use a different
standard of measurement and report a lower capacity. In addition, some of the listed capacity is used for formatting and other functions, and thus will not be available for data storage.
Actual quantities will vary based on various factors, including file size, file format, features and application software. Actual data rates may vary depending on operating environment and
other factors. The export or re-export of hardware or software containing encryption may be regulated by the U.S. Department of Commerce, Bureau of Industry and Security (for more
information, visit www.bis.doc.gov), and controlled for import and use outside of the U.S. Seagate reserves the right to change, without notice, product offerings or specifications.
Contents
Seagate® Technology Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.0
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1
About the SATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.0
Drive Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1
Specification summary tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2
Formatted capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.2.1
LBA mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.3
Default logical geometry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.4
Recording and interface technology. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.5
Physical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.6
Seek time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.7
Start/stop times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.8
Power specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.8.1
Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.8.2
Conducted noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.8.3
Voltage tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.8.4
Power-management modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.9
Environmental specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.9.1
Ambient Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.9.2
Temperature gradient . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.9.3
Humidity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.9.4
Altitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.9.5
Shock and Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.10
Acoustics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.10.1
Test for Prominent Discrete Tones (PDTs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.11
Electromagnetic immunity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.12
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.12.1
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.13
Agency certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.13.1
Safety certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.13.2
Electromagnetic compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.13.3
FCC verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.14
Environmental protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.14.1
European Union Restriction of Hazardous Substances (RoHS) Directive. . . . . . . . . . . . . . 16
2.15
China Requirements — China RoHS 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.16
Corrosive environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.0
Configuring and Mounting the Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.1
Handling and static-discharge precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.2
Configuring the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.3
SATA cables and connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.4
Drive mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.0
SATA Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.1
Hot-Plug compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.2
SATA device plug connector pin definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.3
Supported ATA commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.3.1
Identify Device command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.3.2
Set Features command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4.3.3
S.M.A.R.T. commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Seagate BarraCuda Product Manual, Rev. A
2
Figures
Figure 1
Figure 2
Attaching SATA cabling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Mounting dimensions (4TB). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Seagate BarraCuda Product Manual, Rev. A
3
Seagate® Technology Support Services
For information regarding online support and services, visit: http://www.seagate.com/contacts/
For information regarding Warranty Support, visit: http://www.seagate.com/support/warranty-and-replacements/
For information regarding data recovery services, visit: http://www.seagate.com/services-software/data-recovery-services/
For Seagate OEM, Distribution partner and reseller portals, visit: http://www.seagate.com/partners/
Seagate BarraCuda Product Manual, Rev. A
4
1.0 Introduction
This manual describes the functional, mechanical and interface specifications for the following:
Seagate® BarraCuda® model drives:
ST4000DM005
These drives provide the following key features:
• Compliant with RoHS requirements in China and Europe.
• High instantaneous (burst) data-transfer rates (up to 600MB per second).
• Native Command Queuing with command ordering to increase performance in demanding applications.
• Quiet operation.
• SeaTools diagnostic software performs a drive self-test that eliminates unnecessary drive returns.
• State-of-the-art cache and on-the-fly error-correction algorithms.
• Support for S.M.A.R.T. drive monitoring and reporting.
• Supports latching SATA cables and connectors.
• TGMR recording technology provides the drives with increased areal density.
• Worldwide Name (WWN) capability uniquely identifies the drive.
1.1
About the SATA interface
The Serial ATA (SATA) interface provides several advantages over the traditional (parallel) ATA interface. The primary
advantages include:
• Easy installation and configuration with true plug-and-play connectivity. It is not necessary to set any jumpers or other
configuration options.
• Thinner and more flexible cabling for improved enclosure airflow and ease of installation.
• Scalability to higher performance levels.
In addition, SATA makes the transition from parallel ATA easy by providing legacy software support. SATA was designed to
allow users to install a SATA host adapter and SATA disk drive in the current system and expect all of the existing
applications to work as normal.
The SATA interface connects each disk drive in a point-to-point configuration with the SATA host adapter. There is no
master/slave relationship with SATA devices like there is with parallel ATA. If two drives are attached on one SATA host
adapter, the host operating system views the two devices as if they were both “masters” on two separate ports. This
essentially means both drives behave as if they are Device 0 (master) devices.
The SATA host adapter and drive share the function of emulating parallel ATA device behavior to provide backward
compatibility with existing host systems and software. The Command and Control Block registers, PIO and DMA data
transfers, resets, and interrupts are all emulated.
The SATA host adapter contains a set of registers that shadow the contents of the traditional device registers, referred to as
the Shadow Register Block. All SATA devices behave like Device 0 devices. For additional information about how SATA
emulates parallel ATA, refer to the “Serial ATA International Organization: Serial ATA Revision 3.0”. The specification can be
downloaded from www.sata-io.org.
Note
The host adapter may, optionally, emulate a master/slave environment to host software where two devices
on separate SATA ports are represented to host software as a Device 0 (master) and Device 1 (slave) accessed
at the same set of host bus addresses. A host adapter that emulates a master/slave environment manages
two sets of shadow registers. This is not a typical SATA environment.
Seagate BarraCuda Product Manual, Rev. A
5
www.seagate.com
Drive Specifications
2.0 Drive Specifications
Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For
convenience, the phrases the drive and this drive are used throughout this manual to indicate the following drive models:
ST4000DM005
2.1
Specification summary tables
The specifications listed in Table 1 are for quick reference. For details on specification measurement or definition, refer to
the appropriate section of this manual.
Table 1
Drive specifications summary for 4TB model
Drive Specification*
ST4000DM005
Formatted capacity (512 bytes/sector)**
4000GB (4TB)
Guaranteed sectors
7,814,037,168
Heads
Disks
Bytes per sector (4K physical emulated at 512-byte sectors)
6
3
4096
Default sectors per track
63
Default read/write heads
16
Default cylinders
Recording density (max)
16,383
2054kFCI
Track density (avg)
390ktracks/in
Areal density (avg)
811Gb/in2
Internal data transfer rate (max)
2111Mb/s
Average data rate, read/write (MB/s)
161MB/s
Maximum sustained data rate, OD read (MB/s)
190MB/s
ATA data-transfer modes supported
I/O data-transfer rate (max)
Cache buffer
PIO modes: 0 to 4
Multiword DMA modes: 0 to 2
Ultra DMA modes 0 to 6
600MB/s
64MB
Height (max)
26.1mm / 1.028 in
Width (max)
101.6mm /4.0 in (+ 0.010 in)
Length (max)
146.99mm / 5.787 in
Weight (typical)
635g / 1.400 lb
Average latency
5.1ms
Power-on to ready (max)
15.0s
Standby to ready (max)
15.0s
Average seek, read (typical)
Average seek, write (typical)
<12.0ms typical
<12.0ms typical
Startup current (typical) 12V
2.0A
Voltage tolerance (including noise)
5V ±5%
12V ±10%
Non-Operating (Ambient °C)
–40° to 70°
Operating ambient temperature (min °C)
Operating temperature (drive case max °C)
Temperature gradient
Seagate BarraCuda Product Manual, Rev. A
0°
60°†
20°C per hour max (operating)
30°C per hour max (non-operating)
6
Table 1
Drive specifications summary for 4TB model (continued)
Drive Specification*
ST4000DM005
5% to 90% (operating)
5% to 95% (non-operating)
Relative humidity
Relative humidity gradient (max)
30% per hour
26°C max (operating)
29°C max (non-operating)
Wet bulb temperature (max)
Altitude, operating
–304m to 3048m
(–1000 ft to 10,000 ft)
Altitude, non-operating
(below mean sea level, max)
–304m to12,192m
(–1000 ft to 40,000+ ft)
Operational shock (max)
80 Gs at 2ms
Non-operational shock (max)
300 Gs at 2ms
Vibration, operating
10Hz to 22Hz: 0.25 Gs, Limited displacement
22Hz to 350Hz: 0.50 Gs
350Hz to 500Hz: 0.25 Gs
5Hz to 22Hz: 3.0 Gs
22Hz to 350Hz: 3.0 Gs
350Hz to 500Hz: 3.0 Gs
Vibration, non-operating
Drive acoustics, sound power
Idle***
23 dBA (typical)
25 dBA (max)
Seek
24 dBA (typical)
25 dBA (max)
1 per 1014 bits read
Non-recoverable read errors
Rated workload
Average annualized workload rating: <55 TB/year.
The AFR specification for the product assumes the I/O workload does
not exceed the average annualized workload rate limit of 55 TB/year.
Workloads exceeding the annualized rate may degrade the product
AFR and impact reliability as experienced by the particular
application. The average annualized workload rate limit is in units of
TB per calendar year.
Warranty
To determine the warranty for a specific drive, use a web browser to
access the following web page:
http://www.seagate.com/support/warranty-and-replacements/
From this page, click on “Is my Drive under Warranty”. Users will be
asked to provide the drive serial number, model number (or part
number) and country of purchase. The system will display the
warranty information for the drive.
Load/unload cycles (25°C, 50% rel. humidity)
300,000
Supports hotplug operation per the
Serial ATA Revision 3.2 specification
*
Yes
All specifications above are based on native configurations.
** One GB equals one billion bytes and 1TB equals one trillion bytes when referring to hard drive capacity.
Accessible capacity may vary depending on operating environment and formatting.
*** During periods of drive idle, some offline activity may occur according to the S.M.A.R.T.
specification, which may increase acoustic and power to operational levels.
†
Seagate does not recommend operating at sustained case temperatures above 60°C.
Operating at higher temperatures will reduce useful life of the product.
Seagate BarraCuda Product Manual, Rev. A
7
www.seagate.com
2.2
Drive Specifications
Formatted capacity
Model
Formatted capacity*
Guaranteed sectors
4TB
4000GB
7,814,037,168
Bytes per sector
4096
*One GB equals one billion bytes and 1TB equals one trillion bytes when referring to hard drive capacity. Accessible capacity may vary depending on
operating environment and formatting.
2.2.1 LBA mode
When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the
number of guaranteed sectors as defined above.
See Section 4.3.1, "Identify Device command" (words 60-61 and 100-103) for additional information about 48-bit
addressing support of drives with capacities over 137GB.
2.3
Default logical geometry
• Cylinders: 16,383
• Read/write heads: 16
• Sectors per track: 63
LBA mode
When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the
number of guaranteed sectors as defined above.
2.4
Recording and interface technology
Interface
SATA
Recording method
TGMR
Recording density
2054kFCI
Track density (ktracks/inch avg)
390
Areal density (Gb/in2)
811
Internal data transfer rate (Mb/s max)
2111
Maximum sustained data transfer rate, OD read (MB/s)
190
Average data rate, read/write (MB/s)
161
I/O data-transfer rate (MB/s max)
600
2.5
Physical characteristics
Maximum height
26.1mm / 1.028 in
Maximum width
101.6mm / 4.0 in (± 0.010 in)
Maximum length
146.99mm / 5.787 in
Typical weight
635g / 1.400 lb
Cache buffer
64MB
Seagate BarraCuda Product Manual, Rev. A
8
www.seagate.com
2.6
Drive Specifications
Seek time
Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive
diagnostics. The specifications in the table below are defined as follows:
• Track-to-track seek time is an average of all possible single-track seeks in both directions.
• Average seek time is a true statistical random average of at least 5000 measurements of seeks between random tracks,
less overhead.
Typical seek times (ms)
Read
Write
Track-to-track
1.0
1.2
Average
12.0
12.0
Average latency
Note
2.7
5.1
These drives are designed to consistently meet the seek times represented in this
manual. Physical seeks, regardless of mode (such as track-to-track and average),
are expected to meet the noted values. However, due to the manner in which
these drives are formatted, benchmark tests that include command overhead or
measure logical seeks may produce results that vary from these specifications.
Start/stop times
The start/stop times listed below are for the 4TB models.
Power-on to ready
(in seconds)
13 (typical)
15 (max)
Standby to ready
(in seconds)
13 (typical)
15 (max)
Ready to spindle stop
(in seconds)
10 (typical)
11 (max)
Time-to-ready may be longer than normal if the drive power is removed without going through normal OS powerdown
procedures.
Seagate BarraCuda Product Manual, Rev. A
9
www.seagate.com
2.8
Drive Specifications
Power specifications
The drive receives DC power (+5V or +12V) through a native SATA power connector. Refer to Figure 1 on page 18.
2.8.1 Power consumption
Power requirements for the drives are listed in Table 2. Typical power measurements are based on an average of drives
tested, under nominal conditions, using 5.0V and 12.0V input voltage at 25°C ambient temperature.
• Spinup power
Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed.
• Read/write power and current
Read/write power is measured with the heads on track, based on a 16-sector write followed by a 32-ms delay, then a
16-sector read followed by a 32-ms delay.
• Operating power and current
Operating power is measured using 40 percent random seeks, 40 percent read/write mode (1 write for each 10 reads)
and 20 percent drive idle mode.
• Idle mode power
Idle mode power is measured with the drive up to speed, with servo electronics active and with the heads in a random
track location.
• Standby mode
During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/write electronics are in power-down mode.
Table 2
DC power requirements (4TB)
Power dissipation
(3-disk values shown)
Avg (watts 25° C)
Avg 5V typ amps
Avg 12V typ amps
Spinup
—
—
2.0
Idle1* †
3.20
0.07
0.238
Operating
5.50
0.20
0.33
Standby
0.25
0.04
0.004
Sleep
0.25
0.04
0.004
*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to
operational levels.
†5W IDLE with DIPLM Enabled
2.8.2 Conducted noise
Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on the +12 volt
line or an equivalent 15-ohm resistive load on the +5 volt line.
• Using 12-volt power, the drive is expected to operate with a maximum of 120 mV peak-to-peak square-wave injected
noise at up to 10MHz.
• Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave injected
noise at up to 10MHz.
Note
Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current.
Seagate BarraCuda Product Manual, Rev. A
10
www.seagate.com
Drive Specifications
2.8.3 Voltage tolerance
Voltage tolerance (including noise):
• 5V ±5%
• 12V ±10%
2.8.4 Power-management modes
The drive provides programmable power management to provide greater energy efficiency. In most systems, users can
control power management through the system setup program. The drive features the following power-management
modes:
Power modes
Heads
Spindle
Buffer
Active
Tracking
Rotating
Enabled
Idle
Tracking
Rotating
Enabled
Standby
Parked
Stopped
Enabled
Sleep
Parked
Stopped
Disabled
• Active mode
The drive is in Active mode during the read/write and seek operations.
• Idle mode
The buffer remains enabled, and the drive accepts all commands and returns to Active mode any time disk access is
necessary.
• Standby mode
The drive enters Standby mode when the host sends a Standby Immediate command. If the host has set the standby
timer, the drive can also enter Standby mode automatically after the drive has been inactive for a specifiable length of
time. The standby timer delay is established using a Standby or Idle command. In Standby mode, the drive buffer is
enabled, the heads are parked and the spindle is at rest. The drive accepts all commands and returns to Active mode
any time disk access is necessary.
• Sleep mode
The drive enters Sleep mode after receiving a Sleep command from the host. In Sleep mode, the drive buffer is disabled, the heads are parked and the spindle is at rest. The drive leaves Sleep mode after it receives a Hard Reset or Soft
Reset from the host. After receiving a reset, the drive exits Sleep mode and enters Standby mode with all current translation parameters intact.
• Idle and Standby timers
Each time the drive performs an Active function (read, write or seek), the standby timer is reinitialized and begins
counting down from its specified delay times to zero. If the standby timer reaches zero before any drive activity is
required, the drive makes a transition to Standby mode. In both Idle and Standby mode, the drive accepts all commands and returns to Active mode when disk access is necessary.
Seagate BarraCuda Product Manual, Rev. A
11
www.seagate.com
2.9
Drive Specifications
Environmental specifications
This section provides the temperature, humidity, shock, and vibration specifications for Desktop HDDs. Ambient
temperature is defined as the temperature of the environment immediately surrounding the drive. Above 1000ft. (305
meters), the maximum temperature is derated linearly by 1°C every 1000 ft. Refer to Section 3.4 on page 19 for base plate
measurement location.
2.9.1 Ambient Temperature
†
Non-operating (Ambient)
–40° to 70°C (–40° to 158°F)
Operating ambient (min °C)
0° (32°F)
Operating (Drive case max °C)
60° (140°F) †
Seagate does not recommend operating at sustained case temperatures above 60°C.
Operating at higher temperatures will reduce useful life of the product.
2.9.2 Temperature gradient
Operating
20°C per hour (36°F per hour max), without condensation
Non-operating
30°C per hour (54°F per hour max)
2.9.3 Humidity
2.9.3.1
Relative humidity
Operating
5% to 90% non-condensing (30% per hour max)
Non-operating
5% to 95% non-condensing (30% per hour max)
2.9.3.2
Wet bulb temperature
Operating
26°C / 78.8°F (rated)
Non-operating
29°C / 84.2°F (rated)
2.9.4 Altitude
Operating
–304m to 3048m (–1000 ft. to 10,000 ft.)
Non-operating
–304m to 12,192m (–1000 ft. to 40,000+ ft.)
Seagate BarraCuda Product Manual, Rev. A
12
www.seagate.com
Drive Specifications
2.9.5 Shock and Vibration
All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting
screws. Shock may be applied in the X, Y or Z axis.
2.9.5.1
Operating shock
These drives comply with the performance levels specified in this document when subjected to a maximum operating
shock of 80 Gs based on half-sine shock pulses of 2ms during read operations. Shocks should not be repeated more than
two times per second.
2.9.5.2
Non-operating shock
The non-operating shock level that the drive can experience without incurring physical damage or degradation in
performance when subsequently put into operation is 300 Gs based on a non-repetitive half-sine shock pulse of
2ms duration.
2.9.5.3
Operating vibration
The maximum vibration levels that the drive may experience while meeting the performance standards specified in this
document are specified below.
10Hz to 22Hz
0.25 Gs (Limited displacement)
22Hz to 350Hz
0.50 Gs
350Hz to 500Hz
0.25 Gs
All vibration specifications assume that the drive is mounted securely with the input vibration applied at the drive
mounting screws. Vibration may be applied in the X, Y or Z axis. Throughput may vary if improperly mounted.
2.9.5.4
Non-operating vibration
The maximum non-operating vibration levels that the drive may experience without incurring physical damage or
degradation in performance when subsequently put into operation are specified below.
5Hz to 22Hz
3.0 Gs (Limited displacement)
22Hz to 350Hz
3.0 Gs
350Hz to 500Hz
3.0 Gs
Seagate BarraCuda Product Manual, Rev. A
13
www.seagate.com
2.10
Drive Specifications
Acoustics
Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All measurements are
consistent with ISO document 7779. Sound power measurements are taken under essentially free-field conditions over a
reflecting plane. For all tests, the drive is oriented with the cover facing upward.
Note
For seek mode tests, the drive is placed in seek mode only.
The number of seeks per second is defined by the following equation:
(Number of seeks per second = 0.4 / (average latency + average access time
Table 3
Fluid Dynamic Bearing (FDB) motor acoustics
3-Disk
Idle*
Seek
23 dBA (typical)
25 dBA (max)
24 dBA (typical)
25 dBA (max)
*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to
operational levels.
2.10.1 Test for Prominent Discrete Tones (PDTs)
Seagate follows the ECMA-74 standards for measurement and identification of PDTs. An exception to this process is the
use of the absolute threshold of hearing. Seagate uses this threshold curve (originated in ISO 389-7) to discern tone
audibility and to compensate for the inaudible components of sound prior to computation of tone ratios according to
Annex D of the ECMA-74 standards.
2.11
Electromagnetic immunity
When properly installed in a representative host system, the drive operates without errors or degradation in performance
when subjected to the radio frequency (RF) environments defined in Table 4.
Table 4
Radio frequency environments
Test
Description
Performance
level
Reference
standard
Electrostatic discharge
Contact, HCP, VCP: ± 4 kV; Air: ± 8 kV
B
EN61000-4-2: 95
Radiated RF immunity
80MHz to 1,000MHz, 3 V/m,
80% AM with 1kHz sine
900MHz, 3 V/m, 50% pulse modulation @ 200Hz
A
EN61000-4-3: 96
ENV50204: 95
Electrical fast transient
± 1 kV on AC mains, ± 0.5 kV on external I/O
B
EN61000-4-4: 95
Surge immunity
± 1 kV differential, ± 2 kV common,
AC mains
B
EN61000-4-5: 95
Conducted RF immunity
150kHz to 80MHz, 3 Vrms, 80% AM with 1kHz sine
A
EN61000-4-6: 97
Voltage dips, interrupts
0% open, 5 seconds
0% short, 5 seconds
40%, 0.10 seconds
70%, 0.01 seconds
C
C
C
B
EN61000-4-11: 94
Seagate BarraCuda Product Manual, Rev. A
14
www.seagate.com
2.12
Drive Specifications
Warranty
To determine the warranty for a specific drive, use a web browser to access the following web page:
http://www.seagate.com/support/warranty-and-replacements/
From this page, click on “Is my Drive under Warranty”. Users will be asked to provide the drive serial number, model
number (or part number) and country of purchase. The system will display the warranty information for the drive.
2.12.1 Storage
Maximum storage periods are 180 days within original unopened Seagate shipping package or 60 days unpackaged
within the defined non-operating limits (refer to environmental section in this manual). Storage can be extended to 1 year
packaged or unpackaged under optimal environmental conditions (25°C, <40% relative humidity non-condensing, and
non-corrosive environment). During any storage period the drive non-operational temperature, humidity, wet bulb,
atmospheric conditions, shock, vibration, magnetic and electrical field specifications should be followed.
2.13
Agency certification
2.13.1 Safety certification
These products are certified to meet the requirements of UL60950-1, CSA60950-1 and EN60950 and so marked as to the
certify agency.
The following regulatory model number represent all features and configurations within the series:
Regulatory model Numbers: SKR001
2.13.2 Electromagnetic compatibility
Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Electromagnetic
Compatibility Directive 2014/30/EU. Testing is performed to the levels specified by the product standards for Information
Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and the immunity levels are defined by EN
55024.
Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply with the directives when
used in the test systems, we cannot guarantee that all systems will comply with the directives. The drive is designed for
operation inside a properly designed enclosure, with properly shielded I/O cable (if necessary) and terminators on all
unused I/O ports. Computer manufacturers and system integrators should confirm EMC compliance and provide CE
marking for their products.
Korean RRA
If these drives have the Korean Communications Commission (KCC) logo, they comply with paragraph 1 of Article 11 of the
Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Framework
requirements of the Radio Research Agency (RRA) Communications Commission, Republic of Korea.
These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibility (EMI/
EMS) for Class B products. Drives are tested in a representative, end-user system by a Korean-recognized lab.
Australian RCM Compliance Mark
If these models have the RCM marking, they comply with the Australia/New Zealand Standard AS/NZS CISPR22: 2009 and
meet the Electromagnetic Compatibility (EMC) Framework requirements of the Australian Communication and Media
Authority (ACMA).
Seagate BarraCuda Product Manual, Rev. A
15
www.seagate.com
Drive Specifications
2.13.3 FCC verification
These drives are intended to be contained solely within a personal computer or similar enclosure (not attached as an
external device). As such, each drive is considered to be a subassembly even when it is individually marketed to the
customer. As a subassembly, no Federal Communications Commission verification or certification of the device is required.
Seagate has tested this device in enclosures as described above to ensure that the total assembly (enclosure, disk drive,
motherboard, power supply, etc.) does comply with the limits for a Class B computing device, pursuant to Subpart J, Part
15 of the FCC rules. Operation with non-certified assemblies is likely to result in interference to radio and television
reception.
Radio and television interference. This equipment generates and uses radio frequency energy and if not installed and
used in strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception.
This equipment is designed to provide reasonable protection against such interference in a residential installation.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
interference to radio or television, which can be determined by turning the equipment on and off, users are encouraged to
try one or more of the following corrective measures:
• Reorient the receiving antenna.
• Move the device to one side or the other of the radio or TV.
• Move the device farther away from the radio or TV.
• Plug the computer into a different outlet so that the receiver and computer are on different branch outlets.
If necessary, users should consult the dealer or an experienced radio/television technician for additional suggestions.
Users may find helpful the following booklet prepared by the Federal Communications Commission: How to Identify and
Resolve Radio-Television Interference Problems. This booklet is available from the Superintendent of Documents,
U.S. Government Printing Office, Washington, DC 20402. Refer to publication number 004-000-00345-4.
2.14
Environmental protection
Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting
certain chemical substances.
2.14.1 European Union Restriction of Hazardous Substances (RoHS) Directive
The European Union Restriction of Hazardous Substances (RoHS) Directive, restricts the presence of chemical substances,
including Lead, Cadmium, Mercury, Hexavalent Chromium, PBB and PBDE, in electronic products, effective July 2006. This
drive is manufactured with components and materials that comply with the RoHS Directive.
Seagate BarraCuda Product Manual, Rev. A
16
www.seagate.com
2.15
Drive Specifications
China Requirements — China RoHS 2
China RoHS 2 refers to the Ministry of Industry and Information Technology Order No. 32, effective July 1, 2016, titled
Management Methods for the Restriction of the Use of Hazardous Substances in Electrical and Electronic Products. To
comply with China RoHS 2, we determined this product's Environmental Protection Use Period (EPUP) to be 20 years in
accordance with the Marking for the Restricted Use of Hazardous Substances in Electronic and Electrical Products, SJT 113642014.
中国电器电子产品有害物质限制使用管理办法
(Management Methods for the Restriction of the Use of Hazardous Substances in Electrical and
Electronic Products _ China RoHS)
20
产品中有害物质的名称及含量
(Name and Content of the Hazardous Substances in Product)
Table 5 Hazardous Substances
有害物质
部件名称
Part Name
印刷电路板组装
PCBA
机壳
Chassis
Hazardous Substances
铅
汞
镉
六价铬
多溴联苯
多溴二苯醚
Lead
(Pb)
Mercury
(Hg)
Cadmium
(Cd)
Hexavalent Chromium
(CF (VI))
Polybrominated
biphenyls (PBB)
Polybrominated
diphenyl ethers (PBDE)
X
O
O
O
O
O
X
O
O
O
O
O
本表格依据 SJ/T 11364 的规定编制。
This table is prepared in accordance with the provisions of SJ/T 11364-2014
O:表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量要求以下。
O: Indicates that the hazardous substance contained in all of the homogeneous materials for this part is below the limit
requirement of GB/T26572.
X:表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定的限量要求。
X: Indicates that the hazardous substance contained in at least one of the homogeneous materials used for this part is above the
limit requirement of GB/T26572.
2.16
Corrosive environment
Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to light industrial
environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM B845. However, this
accelerated testing cannot duplicate every potential application environment. Users should use caution exposing any
electronic components to uncontrolled chemical pollutants and corrosive chemicals as electronic drive component
reliability can be affected by the installation environment. The silver, copper, nickel and gold films used in Seagate
products are especially sensitive to the presence of sulfide, chloride, and nitrate contaminants. Sulfur is found to be the
most damaging. In addition, electronic components should never be exposed to condensing water on the surface of the
printed circuit board assembly (PCBA) or exposed to an ambient relative humidity greater than 95%. Materials used in
cabinet fabrication, such as vulcanized rubber, that can outgas corrosive compounds should be minimized or eliminated.
The useful life of any electronic equipment may be extended by replacing materials near circuitry with sulfide-free
alternatives.
Seagate BarraCuda Product Manual, Rev. A
17
www.seagate.com
Configuring and Mounting the Drive
3.0 Configuring and Mounting the Drive
This section contains the specifications and instructions for configuring and mounting the drive.
3.1
Handling and static-discharge precautions
After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD)
hazards. Observe the following standard handling and static-discharge precautions:
Caution
• Before handling the drive, put on a grounded wrist strap, or ground oneself frequently by touching the metal chassis of
a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire installation
procedure.
• Handle the drive by its edges or frame only.
• The drive is extremely fragile—handle it with care. Do not press down on the drive top cover.
• Always rest the drive on a padded, antistatic surface until users mount it in the computer.
• Do not touch the connector pins or the printed circuit board.
• Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids the warranty.
Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and
contamination.
3.2
Configuring the drive
Each drive on the SATA interface connects point-to-point with the SATA host adapter. There is no master/slave relationship
because each drive is considered a master in a point-to-point relationship. If two drives are attached on one SATA host
adapter, the host operating system views the two devices as if they were both “masters” on two separate ports. Both drives
behave as if they are Device 0 (master) devices.
SATA drives are designed for easy installation. It is usually not necessary to set any jumpers on the drive for proper
operation; however, if users connect the drive and receive a “drive not detected” error, the SATA-equipped motherboard or
host adapter may use a chipset that does not support SATA speed autonegotiation.
3.3
SATA cables and connectors
The SATA interface cable consists of four conductors in two differential pairs, plus three ground connections. The cable size
may be 30 to 26 AWG with a maximum length of one meter (39.37 inches). See Table 6 for connector pin definitions. Either
end of the SATA signal cable can be attached to the drive or host.
For direct backplane connection, the drive connectors are inserted directly into the host receptacle. The drive and the host
receptacle incorporate features that enable the direct connection to be hot pluggable and blind mateable.
For installations which require cables, users can connect the drive as illustrated in Figure 1.
Figure 1 Attaching SATA cabling
Each cable is keyed to ensure correct orientation. BarraCuda drives support latching SATA connectors.
Seagate BarraCuda Product Manual, Rev. A
18
3.4
Drive mounting
Users can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottommounting holes. Refer to Figure 2 for drive mounting dimensions. Follow these important mounting precautions when
mounting the drive:
• Allow a minimum clearance of 0.030 inches (0.76mm) around the entire perimeter of the drive for cooling.
• Use only 6-32 UNC mounting screws.
• The screws should be inserted no more than 0.120 inch (3.05mm) into the bottom or side mounting holes.
• Do not overtighten the mounting screws (maximum torque: 6 inch-lb).
Figure 2 Mounting dimensions (4TB)
0.12
0.12
Seagate BarraCuda Product Manual, Rev. A
19
www.seagate.com
SATA Interface
4.0 SATA Interface
These drives use the industry-standard Serial ATA (SATA) interface that supports FIS data transfers. It supports ATA
programmed input/output (PIO) modes 0 to 4; multiword DMA modes 0 to 2, and Ultra DMA modes 0 to 6.
For detailed information about the SATA interface, refer to the “Serial ATA: High Speed Serialized AT Attachment”
specification.
4.1
Hot-Plug compatibility
BarraCuda drives incorporate connectors which enable users to hot plug these drives in accordance with the SATA
Revision 3.2 specification. This specification can be downloaded from www.serialata.org.
4.2
SATA device plug connector pin definitions
Table 6 summarizes the signals on the SATA interface and power connectors.
Table 6 SATA connector pin definitions
Segment
Pin
Function
Signal
Definition
S1
Ground
2nd mate
S2
A+
Differential signal pair A from Phy
S3
A-
S4
Ground
2nd mate
S5
B-
Differential signal pair B from Phy
S6
B+
S7
Ground
2nd mate
Key and spacing separate signal and power segments
Power
P1
V33
3.3V power
P2
V33
3.3V power
P3
V33
3.3V power, pre-charge, 2nd mate
P4
Ground
1st mate
P5
Ground
2nd mate
P6
Ground
2nd mate
P7
V5
5V power, pre-charge, 2nd mate
P8
V5
5V power
P9
V5
5V power
P10
Ground
2nd mate
P11
Ground or LED signal
If grounded, drive does not use deferred spin
P12
Ground
1st mate.
P13
V12
12V power, pre-charge, 2nd mate
P14
V12
12V power
P15
V12
12V power
Notes
1.
All pins are in a single row, with a 1.27 mm (0.050 in) pitch.
2.
The comments on the mating sequence apply to the case of backplane blindmate connector only. In this case, the mating
sequences are:
• the ground pins P4 and P12.
• the pre-charge power pins and the other ground pins.
• the signal pins and the rest of the power pins.
3.
There are three power pins for each voltage. One pin from each voltage is used for pre-charge when installed in a blind-mate backplane configuration.
• All used voltage pins (Vx) must be terminated.
Seagate BarraCuda Product Manual, Rev. A
20
4.3
Supported ATA commands
The following table lists SATA standard commands that the drive supports.
For a detailed description of the ATA commands, refer to the Serial ATA International Organization:
Serial ATA Revision 3.0 (http://www.sata-io.org).
See “S.M.A.R.T. commands” on page 29 for details and subcommands used in the S.M.A.R.T. implementation.
Table 7 SATA standard commands
Command name
Command code (in hex)
Check Power Mode
E5H
Device Configuration Freeze Lock
B1H / C1H
Device Configuration Identify
B1H / C2H
Device Configuration Restore
B1H / C0H
Device Configuration Set
B1H / C3H
Device Reset
08H
Download Microcode
92H
Execute Device Diagnostics
90H
Flush Cache
E7H
Flush Cache Extended
EAH
Format Track
50H
Identify Device
ECH
Idle
E3H
Idle Immediate
E1H
Initialize Device Parameters
91H
Read Buffer
E4H
Read DMA
C8H
Read DMA Extended
25H
Read DMA Without Retries
C9H
Read Log Ext
2FH
Read Multiple
C4H
Read Multiple Extended
29H
Read Native Max Address
F8H
Read Native Max Address Extended
27H
Read Sectors
20H
Read Sectors Extended
24H
Read Sectors Without Retries
21H
Read Verify Sectors
40H
Read Verify Sectors Extended
42H
Read Verify Sectors Without Retries
41H
Recalibrate
10H
Security Disable Password
F6H
Security Erase Prepare
F3H
Security Erase Unit
F4H
Security Freeze
F5H
Security Set Password
F1H
Seagate BarraCuda Product Manual, Rev. A
21
www.seagate.com
Table 7 SATA standard commands (continued)
Command name
SATA Interface
Command code (in hex)
Security Unlock
F2H
Seek
70H
Set Features
EFH
Set Max Address
F9H
Note: Individual Set Max Address
commands are identified by the value
placed in the Set Max Features register as
defined to the right.
Address:
Password:
Lock:
Unlock:
Freeze Lock:
Set Max Address Extended
37H
Set Multiple Mode
C6H
Sleep
E6H
S.M.A.R.T. Disable Operations
B0H / D9H
S.M.A.R.T. Enable/Disable Autosave
B0H / D2H
S.M.A.R.T. Enable Operations
B0H / D8H
S.M.A.R.T. Execute Offline
B0H / D4H
S.M.A.R.T. Read Attribute Thresholds
B0H / D1H
S.M.A.R.T. Read Data
B0H / D0H
S.M.A.R.T. Read Log Sector
B0H / D5H
S.M.A.R.T. Return Status
B0H / DAH
S.M.A.R.T. Save Attribute Values
B0H / D3H
S.M.A.R.T. Write Log Sector
B0H / D6H
Standby
E2H
Standby Immediate
E0H
Write Buffer
E8H
Write DMA
CAH
Write DMA Extended
35H
Write DMA FUA Extended
3DH
Write DMA Without Retries
CBH
Write Log Extended
3FH
Write Multiple
C5H
Write Multiple Extended
39H
Write Multiple FUA Extended
CEH
Write Sectors
30H
Write Sectors Without Retries
31H
Write Sectors Extended
34H
Write Uncorrectable
45H
Seagate BarraCuda Product Manual, Rev. A
00H
01H
02H
03H
04H
22
www.seagate.com
SATA Interface
4.3.1 Identify Device command
The Identify Device command (command code ECH) transfers information about the drive to the host following power up.
The data is organized as a single 512-byte block of data, whose contents are shown in on page 21. All reserved bits or
words should be set to zero. Parameters listed with an “x” are drive-specific or vary with the state of the drive.
The following commands contain drive-specific features that may not be included in the SATA specification.
Table 8
Word
Identify Device commands
Description
Value
Configuration information:
0
1
• Bit 15: 0 = ATA; 1 = ATAPI
• Bit 7: removable media
• Bit 6: removable controller
• Bit 0: reserved
Number of logical cylinders
0C5AH
16,383
Specific configuration:
2
37C8h Device requires SET FEATURES subcommand to spin-up after power-up
and IDENTIFY DEVICE data is incomplete.
738Ch Device requires SET FEATURES subcommand to spin-up after power-up
and IDENTIFY DEVICE data is complete.
8C73h Device does not require SET FEATURES subcommand to spin-up after
power-up and IDENTIFY DEVICE data is incomplete.
C837h Device does not require SET FEATURES subcommand to spin-up after
power-up and IDENTIFY DEVICE data is complete.
C837H
3
Number of logical heads
16
4
Retired
0000H
5
Retired
0000H
6
Number of logical sectors per logical track: 63
003FH
7–9
Retired
0000H
10–19
Serial number: (20 ASCII characters, 0000H = none)
ASCII
20
Retired
0000H
21
Retired
0400H
22
Obsolete
0000H
23–26
Firmware revision
(8 ASCII character string, padded with blanks to end of string)
x.xx
27–46
Drive model number:
(40 ASCII characters, padded with blanks to end of string)
47
(Bits 7–0) Maximum sectors per interrupt on Read multiple and Write multiple (16)
8010H
Trusted Computing feature set options:
48
49
15 Shall be cleared to zero
14 Shall be set to one
13:1 Reserved for the Trusted Computing Group
0 Trusted Computing feature set is supported
Standard Standby timer, IORDY supported and may be disabled
Seagate BarraCuda Product Manual, Rev. A
4000H
2F00H
23
www.seagate.com
Table 8
Word
SATA Interface
Identify Device commands (continued)
Description
Value
Capabilities: (see 7.17.7.17)
50
15 Shall be cleared to zero
14 Shall be set to one
13:2 Reserved
1 Obsolete
0 Shall be set to one to indicate a vendor specific Standby timer value minimum
4000H
51
PIO data-transfer cycle timing mode
0200H
52
Retired (Obsolete)
0200H
53
15:8 Free-fall Control Sensitivity
7:3 Reserved
2 the fields reported in word 88 are valid
1 the fields reported in words (70:64) are valid
0 Obsolete
0007H
54
Number of current logical cylinders (Obsolete)
xxxxH
55
Number of current logical heads (Obsolete)
xxxxH
56
Number of current logical sectors per logical track (Obsolete)
xxxxH
57–58
Current capacity in sectors (Obsolete)
xxxxH
59
15 The BLOCK ERASE EXT command is supported
14 The OVERWRITE EXT command is supported
13 The CRYPTO SCRAMBLE EXT command is supported
12 The Sanitize feature set is supported
11:9 Reserved
8 Multiple logical sector setting is valid
7:0 Current setting for number of logical sectors that shall be transferred per DRQ
data block on READ/WRITE Multiple commands
5C10H
60–61
Total number of user-addressable LBA sectors available
(see Section 2.2 for related information)
*Note: The maximum value allowed in this field is: 0FFFFFFFh (268,435,455
sectors, 137GB). Drives with capacities over 137GB will have 0FFFFFFFh in this field
and the actual number of user-addressable LBAs specified in words 100-103. This
is required for drives that support the 48-bit addressing feature.
0FFFFFFFh*
62
Obsolete
0000H
63
Multiword DMA active and modes supported
(see note following this table)
xx07H
64
Advanced PIO modes supported (modes 3 and 4 supported)
0003H
65
Minimum multiword DMA transfer cycle time per word (120 nsec)
0078H
66
Recommended multiword DMA transfer cycle time per word (120 nsec)
0078H
67
Minimum PIO cycle time without IORDY flow control (240 nsec)
0078H
68
Minimum PIO cycle time with IORDY flow control (120 nsec)
0078H
Seagate BarraCuda Product Manual, Rev. A
24
www.seagate.com
Table 8
SATA Interface
Identify Device commands (continued)
Word
Description
Value
69
Additional Supported
15 CFast Specification Support
14 Deterministic data in trimmed LBA range(s) is supported
13 Long Physical Sector Alignment Error Reporting Control is supported
12 Obsolete
11 READ BUFFER DMA is supported
10 WRITE BUFFER DMA is supported
9 Obsolete
8 DOWNLOAD MICROCODE DMA is supported
7 Reserved for IEEE 1667
6 0 = Optional ATA device 28-bit commands supported
5 Trimmed LBA range(s) returning zeroed data is supported
4 Device Encrypts All User Data
3 Extended Number of User Addressable Sectors is supported
2 All write cache is non-volatile
1:0 Reserved
0000H
70–74
ATA-reserved
0000H
75
Queue depth
001FH
76
SATA capabilities
xxxxH
77
Reserved for future SATA definition
xxxxH
78
SATA features supported
xxxxH
79
SATA features enabled
xxxxH
80
Major version number
07F0H
81
Minor version number
006DH
82
Command sets supported
306BH
83
Command sets supported
7561H
84
Command sets support extension (see note following this table)
6173H
85
Command sets enabled
30xxH
86
Command sets enabled
B441H
87
Command sets enable extension
6173H
88
Ultra DMA support and current mode (see note following this table)
xx7FH
89
Security erase time
xxxxH
90
Enhanced security erase time
xxxxH
92
Master password revision code
FFFEH
93
Hardware reset value
xxxxH
94
Automatic acoustic management
D0D0H
95–99
ATA-reserved
0000H
100–103
Total number of user-addressable LBA sectors available (see Section 2.2 for related
information). These words are required for drives that support the 48-bit
addressing feature. Maximum value: 0000FFFFFFFFFFFFh.
ST4000DM005 = 7,814,037,168
104-105
ATA-reserved
0000H
106
Physical sector size / logical sector size
6003H
Seagate BarraCuda Product Manual, Rev. A
25
www.seagate.com
Table 8
SATA Interface
Identify Device commands (continued)
Word
Description
Value
107
ATA-reserved
0000H
108-111
The mandatory value of the world wide name (WWN) for the drive.
NOTE: This field is valid if word 84, bit 8 is set to 1 indicating 64-bit WWN support.
Each drive will have a unique value.
112-118
ATA-reserved
0000H
119
Commands and feature sets supported
41DEH
120
Commands and feature sets supported or enabled
409CH
121-127
ATA-reserved
0000H
128
Security status
0021H
129–159
Seagate-reserved
xxxxH
160–167
ATA-reserved
0000H
168
Device Nominal Form Factor
0002H
169-205
ATA-reserved
0000H
206
SCT Command Transport
10A5H
207-208
ATA-reserved
0000H
209
Alignment of logical blocks within a physical block
4000H
210-216
ATA-reserved
0000H
217
Nominal media rotation rate
175CH
218-221
ATA-reserved
0000H
222
Transport major version number
107FH
223-229
ATA-reserved
0000H
230-233
Extended Number of User Addressable Sectors
ST4000DM005 = 7,814,037,168
234–254
ATA-reserved
0000H
255
Integrity word
xxA5H
Note
Advanced Power Management (APM) and Automatic Acoustic
Management (AAM) features are not supported.
Note
See the bit descriptions below for words 63, 84, and 88 of the Identify Drive data.
Seagate BarraCuda Product Manual, Rev. A
26
www.seagate.com
SATA Interface
Description (if bit is set to 1)
Bit
Word 63
0
Multiword DMA mode 0 is supported.
1
Multiword DMA mode 1 is supported.
2
Multiword DMA mode 2 is supported.
8
Multiword DMA mode 0 is currently active.
9
Multiword DMA mode 1 is currently active.
10
Multiword DMA mode 2 is currently active.
Bit
Word 84
0
SMART error login is supported.
1
SMART self-test is supported.
2
Media serial number is supported.
3
Media Card Pass Through Command feature set is supported.
4
Streaming feature set is supported.
5
GPL feature set is supported.
6
WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT commands are supported.
7
WRITE DMA QUEUED FUA EXT command is supported.
8
64-bit World Wide Name is supported.
9-10
Obsolete.
11-12
Reserved for TLC.
13
IDLE IMMEDIATE command with IUNLOAD feature is supported.
14
Shall be set to 1.
15
Shall be cleared to 0.
Bit
Word 88
0
Ultra DMA mode 0 is supported.
1
Ultra DMA mode 1 is supported.
2
Ultra DMA mode 2 is supported.
3
Ultra DMA mode 3 is supported.
4
Ultra DMA mode 4 is supported.
5
Ultra DMA mode 5 is supported.
6
Ultra DMA mode 6 is supported.
8
Ultra DMA mode 0 is currently active.
9
Ultra DMA mode 1 is currently active.
10
Ultra DMA mode 2 is currently active.
11
Ultra DMA mode 3 is currently active.
12
Ultra DMA mode 4 is currently active.
13
Ultra DMA mode 5 is currently active.
14
Ultra DMA mode 6 is currently active.
Seagate BarraCuda Product Manual, Rev. A
27
www.seagate.com
SATA Interface
4.3.2 Set Features command
This command controls the implementation of various features that the drive supports. When the drive receives this
command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the
register does not represent a feature that the drive supports, the command is aborted. Power-on default has the read lookahead and write caching features enabled. The acceptable values for the Features register are defined as follows:
Table 9
Set Features command
02H
Enable write cache (default)
03H
Set transfer mode (based on value in Sector Count register)
Sector Count register values:
00H Set PIO mode to default (PIO mode 2)
01H Set PIO mode to default and disable IORDY (PIO mode 2)
08H PIO mode 0
09H PIO mode 1
0AH PIO mode 2
0BH PIO mode 3
0CH PIO mode 4 (default)
20H Multiword DMA mode 0
21H Multiword DMA mode 1
22H Multiword DMA mode 2
40H Ultra DMA mode 0
41H Ultra DMA mode 1
42H Ultra DMA mode 2
43H Ultra DMA mode 3
44H Ultra DMA mode 4
45H Ultra DMA mode 5
46H Ultra DMA mode 6
06H
Enable the PUIS feature set
07H
PUIS feature set device spin-up
10H
Enable use of SATA features
55H
Disable read look-ahead (read cache) feature
82H
Disable write cache
86H
Disable the PUIS feature set
90H
Disable use of SATA features
AAH
Enable read look-ahead (read cache) feature (default)
F1H
Report full capacity available
Note
At power-on, or after a hardware or software reset, the
default values of the features are as indicated above.
Seagate BarraCuda Product Manual, Rev. A
28
www.seagate.com
SATA Interface
4.3.3 S.M.A.R.T. commands
S.M.A.R.T. provides near-term failure prediction for disk drives. When S.M.A.R.T. is enabled, the drive monitors
predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines that a failure is
likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable. S.M.A.R.T. predictability is
limited to the attributes the drive can monitor. For more information on S.M.A.R.T. commands and implementation, see the
Draft ATA-5 Standard.
SeaTools diagnostic software activates a built-in drive self-test (DST S.M.A.R.T. command for D4 H ) that eliminates
unnecessary drive returns. The diagnostic software ships with all new drives and is also available at:
http://seatools.seagate.com.
This drive is shipped with S.M.A.R.T. features disabled. Users must have a recent BIOS or software package that supports
S.M.A.R.T. to enable this feature. The table below shows the S.M.A.R.T. command codes that the drive uses.
Table 10 S.M.A.R.T. commands
Code in features register
S.M.A.R.T. command
D0H
S.M.A.R.T. Read Data
D2H
S.M.A.R.T. Enable/Disable Attribute Autosave
D3H
S.M.A.R.T. Save Attribute Values
D4H
S.M.A.R.T. Execute Off-line Immediate (runs DST)
D5H
S.M.A.R.T. Read Log Sector
D6H
S.M.A.R.T. Write Log Sector
D8H
S.M.A.R.T. Enable Operations
D9H
S.M.A.R.T. Disable Operations
DAH
S.M.A.R.T. Return Status
Note
If an appropriate code is not written to the Features Register, the
command is aborted and 0x04 (abort) is written to the Error register.
Seagate BarraCuda Product Manual, Rev. A
29
Seagate Technology LLC
AMERICAS Seagate Technology LLC 10200 South De Anza Boulevard, Cupertino, California 95014, United States, 408-658-1000
ASIA/PACIFIC Seagate Singapore International Headquarters Pte. Ltd. 7000 Ang Mo Kio Avenue 5, Singapore 569877, 65-6485-3888
EUROPE, MIDDLE EAST AND AFRICA Seagate Technology SAS 16-18 rue du Dôme, 92100 Boulogne-Billancourt, France, 33 1-4186 10 00
Publication Number: 100804656, Rev. A
August 2016
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising