PDF Manual - Swamp Industries
1
CONTENT
14
Important Safety Instructions
15
Safety Precautions
16
Brief Introduction / What’s in the box?
17
Performance Marks
18
Features Rear Panel / Front Panel
19
Performance Marks Turbo Subwoofer
20
Setting up your System
22
Installation Advices
23
Warranty Terms
24
Technical Specifications
25
Wiring Guide
26
Service & Contact
27
This Product is QC checked and shipped in a safe working condition. Maintaining this conditions and to
ensure safe operation the user have to follow the security advises and warning notices: Damages caused by
ignoring this manual will cancel the warranty. The manufacturer is also not responsible for further damages
caused by ignoring this manual.
1. Transportation damages: Please check the device before operating on visible damages caused by
transportation. If you detect any damage on the housing don‘t operate the device, please contact your
dealer.
2. Keep these instructions.
3. Read these instructions.
4. Heed all warnings.
5. Follow all instructions.
6. Never use this apparatus near water.
7. Clean it only carefully outside and this only with a dry cloth.
8. Do not block any ventilation openings. This could cause an overheat of the apparatus.
9. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus that
produce heat. Be sure to place the device always at a safe distance from heat sources.
10. Do not defeat the safety purpose of the polarized or grounding plug. A polarized plug has two blades
with one wider than the other. A grounding plug has two blades and a third grounding pin. The wide
blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket or table specified by the manufacturer or sold with the
apparatus. When a cart or rack is used, use with caution when moving the cart/apparatus combination
to avoid injury from tip-over.
13. Unplug the apparatus during lightning storms or when unused for long period of time.
14. Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged
in any way, such as power supply cord or plug is damaged, liquid has been spilled or have been
exposed to rain or moisture, has been dropped, objects have been fallen into the apparatus or it does
not operate normally.
15. Please keep the unit in a good ventilation environment. Do not install this equipment in a confined
space such as a book case or similar unit. The ventilation should not be impeded that the apparatus
will not overheat.
16. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The
apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as
vases, shall not be placed on/over or beside the apparatus.
17. Intended Use: Use the device exclusively for the intended use
18. Fire Hazard! The materials used in this device are normally flammable. If you need the fire protection
class B1 at your location the unit should be treated periodically by the operator with suitable flame
retardants.
19. Speakers can slip through Bass shock and vibration. Furthermore provide by accidental impacts from
present people in the room are an additional risk. Therefore, the unit must always be protected against
slipping or the area must be cordoned off.
20. Keep away from children and amateurs and people with mental retardation of this unit!
ENGLISH
IMPORTANT
SAFETY INSTRUCTIONS
15
SAFETY
PRECAUTIONS
Be careful when handling mains voltages, they are dangerous! Inside the device there are no
parts that require maintenance.
Never open the device!
Disconnect the device immediately and contact our service department if you detect abnormal
operation (for ex. Fume, overheating)
Make sure that the voltage selector switch is at the correct voltage which is provided in your
country before you switch on the device.
An Operating sound system can cause irreparable hearing damage!
Avoid hearing damages by turning the volume always from “min.” to the demanded level.
DANGER TO LIFE! Dropping loudspeaker boxes cause deathly accidents.
CAUTION
16
BRIEF INTRODUCTION
Thank you for choosing speakers from Monkey Banana.
In these pages, you’ll find a detailed description of the features of the speakers, step-by-step instructions for
its setup and use and full specifications.
Please register your product on www.Monkey-Banana.de to receive technical support and the latest news from
Monkey Banana.
With proper care and adequate air circulation, your speakers will operate trouble-free for many years.
Monkey Banana speaker systems are designed and tested by veteran audio engineers in Germany to meet
your needs in studio monitoring environment. It focuses on the functional goal of delivering pure, original
sound without any additional coloration. The Monkey Banana speakers are self-powered, directly accepting a
line signal from a variety of sources.
ENGLISH
The loudspeakers are designed to overcome all the limitations of conventional studio reference monitors within the audio environment. This system delivers a wide-range frequency response by employing two
extraordinary drivers and unique crossover technology. It boasts a stable and balanced low-mid frequency
response along with a defined mid and high-frequency response as well. Both drivers are magnetically
shielded.
WHAT’S IN THE BOX?
• 1X TURBO SPEAKER
• 1X DETACHABLE POWER CORD
• 1X USER MANUAL
17
PERFORMANCE MARKS TURBO
Applications
According to their structural design the main purposes of this speaker system are near field applications,
for example Mastering Studios, broadcast stations, home studios, professional recording studios, cutting
workspace in TV studios for motion and picture as well for audiophile Hifi users.
2
14
1
3
8
4
5
6
9
10
7
11
12
13
18
FEATURES REAR PANEL
1.
Vent Port
2. Volume Knob: This knob adjusts the gain level. When operating the unit for the first time, start with the volume control set all the way off. Slowly raise the volume control to reach a comfortable listening level.
3. HF Knob:10KHz +/-6dB adjustable.
4. LF Knob:100Hz +/-6dB adjustable
5. Channel Select: Left or Right (Digital input mode only)
6. Input Mode Select: analog or digital
7. Inputs: XLR/TRS - Neutrik® Combo-jack, RCA input, S/PDIF - RCA input for digital signal
8. RCA Input (-10dBv):The RCA input accepts unbalanced signals used to connect signals from unbalanced -10dB devices.
9. S/PDIF Input: S / PDIF - RCA jack for digital signal
10. S/PDIF Thru: S / PDIF - RCA jack for digital signal thru
ENGLISH
11. AC Select (Turbo 5/6/8): Ensure the voltage switch is in the right postition to deliver the voltage used in your country
12. Power Switch: This Switch powers on and off.
13. AC Inlet: This socket accepts a standart IEC-type power cable.
FEATURES FRONT PANEL
14. LED Logo: The Monkey Banana Logo will be lighted as soon as signal source is playing.
After 12 min without (no signal is playing) the speaker turns into Standby Mode, the Logo will be dimmed; the speaker is in “Jungle Protect” - according to [European Directive 2005/32/EG].
As soon as signal is played again the speaker turns on immediately, the Logo will be relighted
19
PERFORMANCE MARKS
TURBO SUBWOOFER
6
6
3
2
4
5
15
8
8
7
1
10
10
15
16
14
16
15
1
9
12
13
20
FEATURES REAR PANEL
1.
Vent Port
3. Xover Frequency – Knob: With this knob you are able to adjust the Crossover frequency between 40Hz and 120Hz.
4. Phase reverse switch: 0°/180°
5. Standby-mode switch: 3 choosable modes ON/AUTO (incomming signal)/OFF
6. XLR Inputs(+4dBu):This inputs accepts XLR type connectors. Connect your audio interface, mixer, or other line-level audio source to this inputs.
7. 6,3 mmTRS Inputs(+4dBu): This inputs accepts TRS 6,3mm type connectors. Connect your audio interface, mixer, or other line-level audio source to this inputs.
8. RCA Inputs (-10dBv): The RCA inputs accepts unbalanced signals used to connect signals from unbalanced -10dB devices.
9. S/PDIF Input: S/PDIF - coaxial digital input
ENGLISH
2. Volume Knob: This knob adjusts the gain level. When operating the unit for the first time, start with the volume control set all the way off. Slowly raise the volume control to reach a comfortable listening level.
10. XLR – Out: Connect these outputs with the input of your studio monitor or any other compatible devices.
12. Power Switch: This Switch powers on and off.
13. AC Inlet: This socket accepts a standart IEC-type power cable.
14. Sub Bypass: Here you can connect your subwoofer with an optional footswitch to mute the subwoofer. ATTENTION! Please do not connect audio signals with this input!
15. TRS Out: Connect these outputs with the input of your studio monitor or any other compatible devices.
16. RCA Out: Connect these outputs with the input of your studio monitor or any other compatible devices.
FEATURES FRONT PANEL
15. LED Logo : The Monkey Banana Logo will be lighted as soon as signal source is playing.
After 12 min without ( no signal is playing) the speaker turns into Standby Mode, the Logo will be dimmed; the speaker is in “Jungle Protect” - according to [European Directive 2005/32/EG].
As soon as signal is played again the speaker turns on immediately, the Logo will be relighted
21
SETTING UP YOUR SYSTEM
1.
For optimal performance of the Turbo series, please read the following thoroughly and carefully prior to
installation.
2.
Unpacking: Please do not touch the speaker cones. The Turbo set is packaged in the box tightly, so your
attention is required when taking the monitors out of the boxes. To avoid possible damage to the speaker
units, hold both sides of the monitor in order to pull it out of the box. The speaker cones should not be
touched in order to avoid damage even after they are out of the box.
3.
Placement: Placing the speakers is one of the most important procedures in order to monitor sound accurately. To monitor with the Turbo performing to their maximum capability, an appropriate listening environment and correct placement are required. Please refer to the following for correct Turbo placement.
XLR/6,3mm Jack
DAW
Digital
coaxial
Powered
speaker
XLR/6,3mm Jack
Audiointerface
XLR/6,3mm Jack
Mixing Console
Foot Switch
(optional)
DIGITAL CONNECTION
ALTERNATIVE CONNECTION
22
INSTALLATION ADVICES
1.
The two units and the listener should basically align to form a regular triangle.
2.
Position the speakers so that the top of the woofers are level with your ears in a
normal listening environment.
3.
Place the speakers vertically with the woofer at the bottom. Placing horizontally
is not recommended.
4.
Setting up a 2.1 - System (with additional Subwoofer). The Turbo Series allows
you to add a Subwoofer (e.g. Turbo10s). In two channels with Subwoofer applications, the common listening distance is generally 1 to 1.5 meters from the left
and right speakers. The speakers should be placed on the position of the listener
and the two speakers form an equilateral triangle refer to the diagram. Left 30
degree to listening position – Subwoofer centered - Right 30 degree to listening
position. Connect the single outputs of your audio interface or your surround
encoder with the speakers.
5.
In 5.1 Surround Sound production, the listening distance for all speakers from
any speaker is typically 1.5 to 2 meters. The placement of the left and right
speakers should form an equilateral triangle with the mix position. The center
speaker should be placed half way between the left and right speakers at
exactly the same distance from the mix position. The left surround and right
surround speakers should be placed the same distance as the left, center and
right speakers, and positioned 110 degrees to 150 degrees relative to the center
speaker. The distance and position of the subwoofer can be adjusted to produce
best bass response in the room. Refer to the following diagram. When installing
the subwoofer, make sure that standing waves are reduced as much as possible
by the characteristic resonances of the listening room (room modes). Move the
subwoofer in the room back and forth and seek a position where the Sound not
blaring or undefined sounds. If they work in the studio, a set-up has proven to be
on the same axis as the studio monitors as a good solution. Move the subwoofer
also for these inventories on the axis back and forth until the sound defined and
appear powerful. In some cases, when it comes to cancellations it is necessary
to operate the Phase reverse switch on the back. If you note a significantly more
pressure and directness result, the position of the phase reverse switch is correct.
ENGLISH
FOR OPTIMAL PERFORMANCE OF THE SPEAKERS, PLEASE READ
THE FOLLOWING ADVISES PRIOR TO INSTALLATION THOROUGHLY
AND CAREFULLY.
REMARKS:
Do not place any obstacles that may block the flow of air in front or between the speakers.
Also remove reflective materials such as glass, mirrors or metal from the listening environment. Place those materials
away from the path of the sound from the Monkey Banana speakers. To eliminate or reduce electrical interference noises
make sure signal and power lines are preferably not installed parallel to each other.
For optimal performance we suggest to use always shielded high quality audio cables.
23
WARRANTY TERMS
IMPORTANT! IGNORING THE FOLLOWING WARRANTY TERMS MAY BE THE WARRANTY
LIMITED OR DECLINED. THE MANUFACTURER IS NOT RESPONSIBLE FOR DAMAGE
CAUSED BY.
a) Monkey Banana reserves the right to decide the method of shipment to determine the service. Delivery only
within Germany, no Express. Special rules for international mail need a special agreement.
b) Monkey Banana reserves the right to decide whether and which parts of the product would to be changed or
if the product is replaced.
c) If you want to return products to Monkey Banana, please contact us before you ship it back.
d) Packaging: Please make sure that the product will be shipped well packaged - preferably in its original
packaging. This minimizes the risk of damage during transit.
e) In case of dispute regarding the warranty is governed by German law.
f) Monkey Banana is not liable for loss of earnings and breaches of duty, which are related to a defect of our
product.
g) Monkey Banana reserves the right to store the data of the buyer for internal purposes.
h) Monkey Banana reserves the right to make changes to the product line without prior notice.
i) Warranty Limitations:
1. Defects were products / components that have been repaired by a third party already, modified or replaced.
This is reserved exclusively for authorized service technicians of Monkey Banana.
2. Improper use (negligence, misuse, improper use, incorrectly applied voltage / overvoltage, use in conjunction with non-compliant products)
3. Damaged speaker enclosure due to scratches, use of non-approved cleaning materials/methods, dirt,
deformed speaker frame, broken connections, holes in the membrane, dust cap, burned voice coil, due not to
follow the manual consciously
4. Other defects caused by dropping, misuse, neglect, fire, moisture, abrasion, rust, fading of the case by
massive solar radiation, lightning strikes and other force majeure.
5. Scorch marks on the boards, which was caused by mishandling.
6. Damage to the product due to inadequate packaging that do not meet the standard requirements for
products of this kind.
7. Damages which are not on the product itself.
8. Altered the original series number label or completely without series number
9. Any accessories are not in the context of the services of this warranty.
IMPORTANT NOTE:
Please never send any products back to us without having contacted us in advance!
Please enclose a detailed description of the fault and the sales invoice!
24
Turbo6
50Hz - 30kHz
>90dB/95dB
>88dB/92dB
0.06%/0.03%
S/N Ratio (A weighted)HF/LF
THD+N @Rated Power HF/LF
Left or Right (Digital input Mode)
Channel Select
L365 x W322 x H449 mm
L14.37 x W12.67 x H17.67 in
L320 x W287 x H389 mm
L12.60 x W11.30 x H15.31 in
L287 x W255 x H346 mm
L11.29 x W10.03 x H13.62 in
Dimension
ENGLISH
9.1 kg/20 lb
7.6 kg/16.7 lb
7.5 kg/16.5 lb
6 kg/13.2 lb
Gross Weight
+4dBu(Balanced), -10dBv(Unbalanced)
5.9 kg/12.9 lb
4.5 kg/9.9 lb
Input Sensitivity
Net Weight
20K ohms balanced, 10K ohms unbalanced
Input Impedance
L425 x W385 x H522 mm
L16.73 x W15.15 x H20.55 in
15 kg/33 lb
12.2 kg/26.8 lb
Positive signal at + input produce outward LF cone displacement
Analog or Digital
Input Mode Select
Polarity
S/PDIF Thru Connector for digital signal
Output Connectors
0.04%/0.02%
>94dB/100dB
30W
80W
45Hz - 30kHz
XLR/TRS Combo Connectors, RCA Connectors, S/PDIF Connectors for digital signal
0.05%/0.02%
>92dB/98dB
30W
Turbo8
8 Inches Magnetically Shielded
Polypropylene ceramic cone
Input Connectors
0.05%/0.02%
30W
20W
HF Amplifier Power
60W
3kHz
30W
LF Amplifier Power
50W
-6 dB ~ +6 dB Variable @ 100 Hz
-6 dB ~ +6 dB Variable @ 10 kHz
55Hz - 30kHz
6 1/2 Inches Magnetically Shielded
Polypropylene ceramic cone
1 inch silk dome
5 1/4 Inches Magnetically Shielded
Polypropylene ceramic cone
Active near field studio monitor with digital input
Turbo5
LF Level
60Hz - 30kHz
4 Inches Magnetically Shielded
Polypropylene ceramic cone
Turbo4
Crossover Frequency
HF Level
Frequency Response
HF Driver
LF Driver
Type
Model
Turbo10s
L500 x W500 x H523 mm
L19.68 x W19.68 x H20.59 in
22.4 kg/49.2 lb
18.7 kg/41.1 lb
XLR&TRS Connector, RCA Connectors
S/PDIF Thru Connector for digital signal
0.08%
>90dB
300W
40Hz -120Hz adjustable
20Hz to 120Hz
10 inches paper cone
Digital active Subwoofer
TECHNICAL
SPECIFICATION
25
WIRING GUIDE
26
Service & contact
Future Beat Industries GmbH | Gutedelstr. 13
D – 79418 Schliengen
Tel: +49-(0)76 35 – 4 296 03-0
Fax: +49-(0)76 35 – 42 94 76
ENGLISH
eMail: info@monkey-banana.de
The name and the logo „Monkey Banana“ is a registered trademark of Future Beat Industries GmbH
All rights reserved and based on our general business terms
27
28
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising