Copper Bathtub
Copper Bathtub
INSTALLATION INSTRUCTIONS
P50011
1008450_2_A
1 of 8
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX 1-888-272-3094.
Copper Bathtub
INSTALLATION INSTRUCTIONS
Thank You For Choosing KALLISTA
We appreciate your commitment to KALLISTA quality products. Please take a moment to review this manual
before you install your KALLISTA product. If you encounter any installation or performance problems, please do
not hesitate to contact us at the phone number listed at the bottom of the page.
Before You Begin
‰‰ Inspect the bath for damage before you begin installation.
‰‰ You must install this bath to an adequately supported, level floor.
‰‰ Please read these instructions carefully to familiarize yourself with the required tools, material, and
installation sequences.
‰‰ Confirm adequate mounting and connection space for the faucet specified for your installation.
‰‰ Refer to the KALLISTA website for care and cleaning information.
‰‰ KALLISTA reserves the right to make revisions in the design of products without notice, as specified in the
Price Book.
Tools and Materials
Plus
1008450_2_A
2 of 8
Pencil
Tape
Measure
Drill
Pipe
Wrench
hacksaw
Clear 100% Silicone
Sealant or Caulk
●● Fasteners appropriate for mounting
support brackets to finished floor.
●● Drill bits and hole saws appropriate for
finished floor material.
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX 1-888-272-3094.
Copper Bathtub
INSTALLATION INSTRUCTIONS
rough-in information
Hot & Cold
Supply Holes
Waste & Overflow Hole
16-3/4”
(42.5 cm)
31-1/2”
(80 cm)
14-3/4”
(37.5 cm)
15-3/4”
(40.1 cm)
32-1/2”
(82.5 cm)
64-15/16”
(165 cm)
30-3/16”
(76.6 cm)
23-1/4”
(59 cm)
52-3/8”
(133 cm)
PRODUCT INFORMATION
Fixture*:
Top Area
64-15/16” (165 cm)
Bathing Well
x 31-1/2” (80 cm)
To Overflow
Inside Area
Weight
48-5/8” (123.5 cm)
x 19-1/2” (49.5 cm)
275 lbs.
(124.7 kg)
Water Depth
Capacity
16” (41 cm)
75 gal. (283.9 L)
*Approximate Measurements For Comparison Only
1008450_2_A
3 of 8
roughing-in notes
Floor support under bath must provide for a minimum of
115 lbs/square foot (561.5 kg/square meter) loading.
Hot water supply should be 70% of capacity or greater.
Installations will vary.
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX 1-888-272-3094.
Copper Bathtub
INSTALLATION INSTRUCTIONS
1. Opening the crate & Unpacking the bath
‰‰ Remove the lid and sides of the crate by removing the screws.
‰‰ Remove the screws from the strap cleats and remove the straps from the tub.
‰‰ Lift the bath off the base to remove it from crate.
2. Prepare the site
14-3/4” (37.5 cm)
16-3/4” (42.5 cm)
CL
CL
CL
CL
‰‰ Refer to the rough-in information to determine the location for the tub, supplies, and drain.
‰‰ Mark the location and drill the holes for the hot and cold supplies and the drain (waste) on the finished floor.
‰‰ Install the faucet risers according the manufacturer’s instructions.
1008450_2_A
4 of 8
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX 1-888-272-3094.
Copper Bathtub
INSTALLATION INSTRUCTIONS
3. Attach the drain to the tub
Screw
Strainer Basket
with Seal
Apply silicone caulk.
Drain Pipe
Drain Assembly
Apply silicone caulk.
‰‰ Remove the drain assembly and drain pipe from the tee.
‰‰ Remove the strainer basket and seal from the drain assembly.
‰‰ Feed the drain pipe through the hole in the tub base.
‰‰ Apply a bead of silicone caulk to the top of the drain assembly.
‰‰ Apply a bead of silicone caulk to the underside of the strainer basket flange.
‰‰ Place the drain assembly over the drain hole in the underside of the tub.
‰‰ Place the strainer basket and seal in the drain hole from inside the tub.
‰‰ Loosely but securely attach the drain to the tub by screwing through the strainer and strainer basket into
the drain assembly.
1008450_2_A
5 of 8
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX 1-888-272-3094.
Copper Bathtub
INSTALLATION INSTRUCTIONS
4. Attach the overflow to the tub
Overflow Assembly
Overflow Hood
o-o
-oo-o
-o-o-o
-o-o
o-o
o-oo-o-o-oo-o-o
o-o-o-o-o-o-o-o-o-o
o-o-o-o-o-o-o-o-o-o-o-o-o-o
-o-o-o-o-o
-o-o-o-o-o-o-o-o-o-o-o-o-o-o-o-o-o-o-o-o-o-o-o-o-o-o-o-o-o-o-o-o-o-o-o-o
Gasket
Starfish Finial with
Threaded Rod
Drain Plug Chain
oo-o
-oo-o
-o-o
-o-o
-o-oo-o-o-o
-o
‰‰ Remove the starfish finial, overflow hood and gaskets from overflow assembly.
‰‰ Place the gasket over the overflow flange.
‰‰ Place overflow flange over overflow hole on outside of tub.
‰‰ Feed threaded rod of finial through hole in overflow hood and screw it into overflow flange as far as it will
go.
‰‰ With overflow lightly against tub wall, measure distance between overflow hood and underside of starfish
finial. This is the distance the threaded rod will need to be shortened by.
‰‰ Disassemble the overflow from the tub.
‰‰ Mark and cut the threaded rod to size.
‰‰ Place ring for drain plug chain over threaded rod. Re-assemble overflow to tub.
1008450_2_A
6 of 8
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX 1-888-272-3094.
Copper Bathtub
INSTALLATION INSTRUCTIONS
5. Complete waste and overflow assembly
Seal
Nut
Overflow
Pipe
Nut
Seal
Tee
Seal
Nut
Tail Piece
Nut
Seal
Decorative
Box
‰‰ Place decorative box over drain pipe at base of tub.
‰‰ Assemble overflow pipe, tee, tailpiece, nuts and seals to drain pipe and overflow loosely, but securely.
‰‰ Slide the flange onto the tailpiece.
1008450_2_A
7 of 8
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX 1-888-272-3094.
Copper Bathtub
INSTALLATION INSTRUCTIONS
6. Complete installation
Vertical Support Channel
Screw
Support Bracket
Hole in Finished Floor
‰‰ Lift tub and position so that the tailpiece is in the hole in the floor and tub is in desired location.
‰‰ Make any adjustments required to waste and overflow and tighten all connections above the floor.
‰‰ Lift the tub slightly off the floor and place one of the four support brackets under the bottom rim of the tub
directly below one of the vertical support channels. Lift the tub again and mark the location of the hole in
the support bracket. Repeat with the remaining three support brackets.
‰‰ Carefully set tub aside.
‰‰ Attach support brackets to floor using method and fasteners appropriate for your floor material.
‰‰ If desired, the tailpiece can be removed and connected to waste plumbing at this time.
‰‰ Position the tub in desired location, making necessary drain connections.
‰‰ Verify the bottom rim of the tub is supported by all four support brackets.
‰‰ If desired, apply a bead of silicone around the perimeter of the bottom rim, where it meets the floor.
‰‰ Install the tub filler according to the manufacturer’s instructions.
1008450_2_A
8 of 8
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX 1-888-272-3094.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising