Multifunctional counter tico 772/773/774 tico 772/773/774

Multifunctional counter tico 772/773/774 tico 772/773/774
tico 772/773/774
Multifunctional counter tico 772/773/774
niversally applicable as a tachometer, timer, shift counter, batch counter …
U
Easy to operate
Four different backlight colours
Intensity of backlighting can now be adjusted
Large, clearly readable 48 x 48 mm display
Input frequency up to 60 kHz
Easy installation via plug-in terminals
Three presets
TECHNICAL DATA
GENERAL
Display
LCD reflective,
Transflective positive: black figures on backlit background
Transmissive negative: white, red or green figures on backlit
ground, 2 lines, 6-digit counter readings & presets;
leading zero suppression, decimal point (up to 4 decimal places)
Digit height
1st line 9.3 mm; 2nd line 7.2 mm
Supply voltage
SELV: 12-30 VDC; reverse polarity protected
SELV: 24 VAC, 50/60 Hz ± 10%
115 VAC; 230 VAC, 50/60 Hz ± 10%
100-240 VAC 50/60 Hz ± 10% with switch-mode power supply
Current consumption 12-30 VDC <200 mA,
12-30 VDC <250 mA with backlight
24 VAC <250 mA; including sensor supply
115/230 VAC <50 mA; including sensor supply
90 VAC max. 80 mA; including sensor supply with switch-mode
power supply
Power consumption <5 W
<8 W with switch-mode power supply
Duty cycle
100%
Overload protection External fuse DC: 0.16 AT (IEC 127); DC: 0.2 AT (UL 198)
24 VAC: 315 mAT; 230 VAC: 32 mAT; 115 VAC: 63 mAT
Overload protection
Relay outputs
External fuse 230 V, 2.5 mAT
DC: 0.16 AT (IEC 127);
DC: 0.2 AT (UL 198)
24 VAC: 315 mAT
230 VAC: 32 mAT; 115 VAC: 63 mAT
Sensor supply
Transformer:
AC operation: 12-24 VDC (load dependent), max. 50 mA
Switch-mode power supply:
AC operation: 24 VDC/-5%, max. 115 mA
max. capacitive load = 470 µF
Data storage
Non-volatile memory >10 years
Electrical connection Plug-in screw-type connections/terminals
Wire cross-section
Data sheet tico 772/773/774
22/01/2014
1-1.5 mm² with wire-end sleeves
All rights reserved
Page 1 of 7
tico 772/773/774
Multifunctional counter tico 772/773/774
Amplitude threshold <2 V and >8 V or <1 V and >4 V at TTL level,
Amplitude max. 40 VDC
Active edge
Programmable positive for PNP input,
negative for NPN input
Input resistance
Approx. 10 kOhm
Count frequency
Max. 60 kHz; 30 Hz attenuated
max. 20 kHz; 30 Hz attenuated in TTL operation
Application input max. 6 kHz/30Hz attenuated
To prevent the maximum input frequency of 60 kHz being
exceeded, the following maximum input frequencies apply:
Phase discriminator, single evaluation: A and B, each 30 kHz (20 kHz) TTL
Phase discriminator, double evaluation: A and B, each 30 kHz (20 kHz) TTL
Phase discriminator, quad evaluation: A and B, each 15 kHz (15 kHz) TTL
Single-channel metering & directional input: input A 60 kHz (20 kHz) TTL
Differential metering, totalizing: input A + B 60 kHz (20 kHz) TTL
If the application input is also used as a metering input:
Single-channel metering & directional input: input A + app. input
60 kHz (20 kHz) TTL
Differential metering, totalizing: input A + B + app. input
60 kHz (20 kHz) TTL
->refer to graph on Page 5
Pulse wave shape
Any (at max. frequency, square 1:1)
Pulse duration min.
17 ms (30 Hz); 8 µs (60 kHz)
Prescaler0.0001-99.9999
Reset
Manual reset via keyboard, external static or dynamic reset,
min. pulse length 5 ms, automatic reset after reaching Preset 2.
No pulse losses at max. counter frequency due to automatic reset
function. Via programmable application input and programmable
power-on reset
Set function
Setting to Preset 0 (independent of reset)
Display and
preset range
-999,999 to +999,999
Alarm signal
Display flashes when preset 0, 1 or 2 is active
Signal times
0.01 s to 599.99 s or bistable programming; tolerance ± 10 ms;
active on or off
Relay
(Presets 1 and 2)
Change-over contact max.: 250 VAC/30 VDC/5 A
Change-over contact min.: 5 VAC/5 VDC/10 mA;
delay <10 ms
Transistor output
PNP output
(Presets 1 + 2)
12-30 VDC, max. 50 mA for DC supply
12-24 VDC, max. 30 mA for AC supply
24 VDC, max. 50 mA for AC supply with switchmode power supply
Application output PNP output
12-30 VDC, max. 20 mA for DC supply
12-24 VDC, max. 20 mA for AC supply
24 VDC, max. 20 mA for AC supply with switchmode power supply
AC transformer only Combined current load of outputs (sensor 12-24 VDC, Out1, Out2, app. output) must not exceed 65 mA.
Data sheet tico 772/773/774
22/01/2014
All rights reserved
Page 2 of 7
tico 772/773/774
Multifunctional counter tico 772/773/774
COUNTER
BATCH COUNTER
SHIFT COUNTER
TACHOMETER
TIMER
Counter mode
Input A,B
Unidirectional; adding or subtracting; directional input;
Differential operation, add/sub; totalizing add/add;
phase discriminator single, double or quadruple evaluation
Control input
Reset, gate
Preselect modes
Absolute or trailing, range signal/
limit values (signal 1 <P1, signal 2 >P 2)
Application
input/output
Output: prescaler out, preset 0 out, direction out
Input: additional counter input add/sub, reset, set, gate, keylock,
hold, teach in
Mode
Batch counter with preset or 2nd totalizer with preset
Counter mode
of operation
Differential counting add/sub, totalizing add/add
Measuring principle
Period (cycle) measurement (1/tau)
Time base
1/min or 1/s
Min. frequency
1 Hz or 0.1 Hz
Limit values
2 alarms with programmable startup suppression + 1 additional
upper limit value on the application output
Tachometer
mode of operation
Unidirectional add/sub; directional input
Differential add/sub; totalizing add/add;
Phase discriminator single, double or quadruple evaluation
A/B or (A-B)/A%
Application
input/output
Output: Preselect 0 out, direction out
Input: Additional counter input add/sub, keylock, hold, teach in
Accuracy of the
tachometer function
Time base:
Measuring principle:
Measuring time:
Measuring resolution:
Display resolution:
Overall tolerance
= displayed resolution + tolerance of timebase = 130 ppm
Measuring principle
Pulse-width or cycle duration measurement
Start input A + Stop input B; Start/Stop key
Time base
Programmable in sec, min, h or hh.mm.ss
Resolution
1; 0.1; 0.01; 0.001; 0.0001
Function
Single-pulse or cumulative measurement
Application Output: input/output
Input:
Data sheet tico 772/773/774
22/01/2014
All rights reserved
± 30 ppm
cycle duration measurement
min. 0.5s/max. 1s or 10s
0.4µs (<30 ppm)
4 decimal places, 1 digit = 100 ppm
preset 0 out,
additional run, stop, reset, set, keylock, hold,
teach in
Page 3 of 7
tico 772/773/774
Multifunctional counter tico 772/773/774
ENVIRONMENTAL REGULATIONS,
SAFETY PROVISIONS
Accuracy
of the timer
Time base:
± 30 ppm
Start/Stop-point in time: 16 µs/16 ms (not damped/damped)
Resolution:
100 µs = 100 ppm
Overall tolerance
= Displayed resolution + tolerance of timebase = 130 ppm
Safety provisions
EN 61 010-1/IEC 61010-1
Protection class
II; EN 61010-1/IEC 61010-1
Pollution degree
V 2, EN 50178
EMC interference
compatibility
EN 61326-1 industrial environment**
EMC emissions
EN 61326-1 Class B**
Ambient temperature 0°-50°C EN 60 068-2-1/2
Storage temperature -20° to +65°C EN 60 068-2-1/2
Climate
40°C/93% rel. humidy class 4K4H, EN 60 068-2-78
25-50°C/93% rel. humidity cyclical, EN 60 068-2-38
Ingress protection
IP 65 front; EN 60529
IP 20 terminals
Vibration resistance
10 m/s² (10 to 150 Hz); IEC 60 068-2-6
Shock resistance
100 m/s² (18 ms); IEC 60 068-2-27
Resistance
to chemicals
Front film to DIN 42 115-2
Approvals
UL, CSA (pending)
RoHSCompliant
PHYSICAL DATA
Installation
Front-panel installation with tenter (frame)
Front panel thickness max. 11 mm
Dimensions
In accordance with DIN 43700, 48 mm x 48 mm x 118 mm,
installation depth 110 mm
Front-panel cutout
45 mm x 45 mm + 0.3 mm
Weight
Approx. 200 g
** For cable lengths >30 m, connection to DC supply and input level TTL,
additional protective circuits will be necessary.
Data sheet tico 772/773/774
22/01/2014
All rights reserved
Page 4 of 7
COUNTING FREQUENCY AS A
FUNCTION OF SIGNAL VOLTAGE
80
Counting frequency [kHz]
70
60
PNP-H
50
NPN-H
40
30
20
10
0
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
Signal voltage [V]
The counting frequencies were determined using a signal generator with an output
resistance of 50 ohms.
DIMENSIONED DRAWINGS
Data sheet tico 772/773/774
22/01/2014
All rights reserved
Page 5 of 7
tico 772/773/774
Multifunctional counter tico 772/773/774
CONNECTION OPTIONS
Data sheet tico 772/773/774
VDC 2 relays/2 transistors
VDC 1 relay/2 transistors
VAC Transformer 2 relays/2 transistors
VAC Transformer 1 relay/2 transistors
VAC Switch-mode power supply
2 relays/2 transistors
VAC Switch-mode power supply
1 relay/2 transistors
USB interface on Tico 773
RS232 interface on Tico 774
22/01/2014
All rights reserved
Page 6 of 7
tico 772/773/774
Multifunctional counter tico 772/773/774
ORDER INFORMATION
Display
Relays
12-30 VDC
24 VAC
115 VAC
230 VAC
100-240 VAC
Tico 772
LCD reflective
1
0 772 101
0 772 111
0 772 121
0 772 131
0 772 141
LCD reflective
2
0 772 112
0 772 122
0 772 132
0 772 142
Transflective positive
Transflective positive
Transmissive negative
Transmissive negative
Transmissive red
Transmissive red
Transmissive green
Transmissive green
1
0 772 102
0 772 201
-
-
-
0 772 241
2
0 772 202
-
-
-
0 772 242
1
0 772 301
-
-
-
0 772 341
2
0 772 302
-
-
-
0 772 342
1
0 772 401
-
-
-
0 772 441
2
0 772 402
-
-
-
0 772 442
1
0 772 501
-
-
-
0 772 541
2
0 772 502
-
-
-
0 772 542
LCD reflective
1
0 773 101
-
-
-
0 773 141
LCD reflective
2
-
-
0 773 142
1
0 773 102
0 773 201
-
Transflective positive
Transflective positive
Transmissive negative
Transmissive negative
Transmissive red
Transmissive red
Transmissive green
Transmissive green
-
-
-
0 773 241
2
0 773 202
-
-
-
0 773 242
1
0 773 301
-
-
-
0 773 341
2
0 773 302
-
-
-
0 773 342
1
0 773 401
-
-
-
0 773 441
2
0 773 402
-
-
-
0 773 442
1
0 773 501
-
-
-
0 773 541
2
0 773 502
-
-
-
0 773 542
Tico 773 with USB port
Tico 774 with RS232 port
LCD reflective
1
0 774 101
-
-
-
0 774 141
LCD reflective
2
-
-
0 774 142
1
0 774 102
0 774 201
-
Transflective positive
Transflective positive
Transmissive negative
Transmissive negative
Transmissive red
Transmissive red
Transmissive green
Transmissive green
-
-
-
0 774 241
2
0 774 202
-
-
-
0 774 242
1
0 774 301
-
-
-
0 774 341
2
0 774 302
-
-
-
0 774 342
1
0 774 401
-
-
-
0 774 441
2
0 774 402
-
-
-
0 774 442
1
0 774 501
-
-
-
0 774 541
2
0 774 502
-
-
-
0 774 542
Transflective positive: black figures on a white background
Transmissive negative: white figures on a dark background
Transmissive red: red figures on a dark background
Transmissive green: green figures on a dark background
Data sheet tico 772/773/774
22/01/2014
All rights reserved
Page 7 of 7
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising